Kobe CX1836GS Kitchen Hood
Contents
1. 20 PRODUCT REGIS RAIN 27 READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING ALL WIRING MUST BE DONF BY A P ACCORDANCE WITH NATIONAL AND 221547 Ver 032106 IMPORTANT SAFETY INSTRUCTIONS PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR PERSONAL INJURY OBSERVE THE FOLLOWING 1 Installation and electrical wiring must be done by qualified professionals and in accordance with applicable codes and standards including fire rated construction 2 When cutting or drilling into wall or ceiling be careful not to damage electrical wiring or other hidden utilities 3 Ducted hood must be vented to the outside a Before servicing or cleaning unit SWITCH POWER OFF AT SERVICE PANEL b Clean fan filter if any and grease laden surfaces frequently To reduce the risk of fire and properly disperse air make sure to vent air outside DO NOT vent exhaust air into wall spaces attics crawl spaces or garages NOTE This warranty is invalid without an authorized agents receipt or if unit is damaged due to misuse poor installation improper use mistreatment negligence or any other circumstances beyond the control of KOBE RANGE HOODS authorized agents Any repair carried out without the supervision of KOBE RANGE HOODS authorized agents will automatically void the warranty KOBE RANGE HOODS will not be held responsible for any damages to perso2. 16 MODEL NO CX1830GS 8 CX1836GS 8 CX1842GS 8 RECIRCULATING KIT OPTIONAL Model No RD 0183 8 CX1830GS 8 CX1836GS 8 CX1842GS CIRCUIT DIAGRAM MODEL ZH09 AOZL S MOIISA dy u io Noll A eG Uda 3102 Josueg lasued Processor Board INO enig enig Jeuuojsue1 uj pes 54677 18 DISCLAIMER 1 CAREFULLY INSPECT ALL ITEMS FOR DAMAGES BEFORE ACCEPTING DELIVERY NOTE ANY DAMAGES ON THE FREIGHT BILL OR EXPRESS RECEIPT REQUEST NAME AND SIGNATURE OF THE CARRIER S AGENT AND KEEP COPY TO SUPPORT YOUR CLAIM Upon acceptance of items owner assumes responsibility for its safe arrival Damages should be reported to carrier and a claim filed Failure to do this could result in the carrier refusing to honor your claim The carrier will furnish you with necessary forms for filing a claim DAMAGES CAUSED DURING TRANSIT ARE NOT COVERED UNDER OUR WARRANTY 2 PLEASE INSPECT CONTENTS OF PACKAGE S CAREFULLY UPON RECEIVING We must be notified in writing of any damages and or missing parts within the allocated days upon receipt of package s Contact your local KOBE dealer or distributor or call KOBE for the time limit CLAIMS WILL NOT BE ACCEPTED AFTER THE ALLOCATED DAYS NOTE ITEMS WERE THOROUGHLY TESTED AND CAREFULLY PACKED IN OUR FACTORY 3 Products mu
3. 15 VIEW FROM THE SIDE PLASTIC DAMPER PARTS LIST MODEL NO CX1830GS 8 CX1836GS 8 CX1842GS 8 NO DESCRIPTION MODEL SIZE PART NO 1 Oil Container Round 1 001 2 Stainless Steel Filter Screw FT S 1 3 Stainless Steel Filter 1 FBL A009 4 Stainless Steel Mesh Filter 1 HGF A100 5 Halogen Light Support 1 FAV J703 6 Halogen Light 12V 20W Max 1 FAV ZJ01 7 Bottom Casing 1 FAZ A001 8 Control Board 1 HDC G100 Control Button 1 FAZ J100 9 Control Box Screw FT S 2 10 Hood Casing 1 FAZ A100 11 Hood Mounting Bracket 1 FAZ M002 12 Plastic Damper 1 011 13 Transformer 1 HAN J101 14 Electrical Wire Box 1 FAV G001 15 Processor Board 1 FAX G100 16 Capacitor 1 HAN G001 17 Rubber Seal 1 005 18 Air Chamber 1 FAV F160 19 Motor 1 HAN F110 20 Blower 1 FAV F170 21 Locknut 1 FAA F205 22 Blower Cover 1 FAV F120 23 Duct Cover Mounting Bracket 1 020 24 Inner Duct Cover 1 HJS MO001 25 Chamber Cover 1 FAV A006 26 Outer Duct Cover 1 HJS A100 27 Glass Canopy Screw FT S 4 28 Glass Canopy 30 CX183 30G 36 CX183 36G 42 CX183 42G 29 LED Screen 1 FAZ A002 30 Control Panel Screw FI S 3 RECIRCULATING KIT Optional Model No RD 0183 NO DESCRIPTION MODEL SIZE PART NO 31 1 HGF M100 32 Carbon Filter Frame 1 HGF A100 39 Carbon Filter 1 HJT F101
4. 10505 Valley Blvd Suite 302 2 Monte CA 91731 U S A Tel 626 350 1355 Fax 626 350 1976 Email customerservice KOBERangeHoods com Website www KobeRangeHoods com 21 PRODUCT REGISTRATION Register Your Product Any covered failure occurring within two years of original purchase arising from defective workmanship or material in manufacture will be repaired or at our option the unit will be replaced free of charge by an authorized KOBE Range Hoods Agent or KOBE Range Hoods as applicable Keep proof of purchase original invoice handy for inspection If the range hood is sold by the original purchaser during the warranty period the new owner is protected until expiration of the original purchaser s warranty See warranty section for complete warranty coverage information This appliance has been manufactured tested and inspected to the standards required by KOBE Range Hoods PLEASE MAIL IN YOUR WARRANTY REGISTRATION CARD AND PROOF OF PURCHASE TO KOBE Range Hoods 10505 Valley Blvd Suite 302 El Monte CA 91731 RECORD THE FOLLOWING INFORMATION FOR YOUR RECORD Model No Serial No Purchased Date Purchased From IMPORTANT PLEASE KEEP A COPY OF YOUR SALE RECEIPT OR INVOICE HANDY WHEN REQUESTING SERVICE 22 KOBE Range Hoods 10505 Valley Blvd Suite 302 oan Gabriel CA 91731 USA http www KOBERangeHoods com KOBE hoods are made for use in the USA and CANADA only We do not recommend using the ho
5. 18 Power Control Press Power Control to turn On Off the hood Output Display Auto Control Press Auto Control to set the hood on auto sensor When smoke gas or fluctuating temperature is detected hood automatically turns on at prior speed setting Temperature Higher than normal room temperature Output Display 10 opeed Control Press once for High speed to start Output Display 0 Press twice for Low speed to start Output Display Light Control Press Light Control to turn on the two halogen lights Timer Control Press Timer Control to start timer When Timer Control is pressed fan will automatically shut off after set time Timer range from 1 min to 99 mins To clear the timer press Power Control OFF and then press Power Control ON again 11 MAINTENANCE CAUTION NEVER PUT YOUR HAND INTO THE AREA HOUSING THE FAN WHILE THE FAN IS OPERATING For optimal operation clean range hood surface stainless steel filter and oil container regularly To Clean Hood Surface CAUTION NEVER USE ABRASIVE CLEANERS PADS OR CLOTHS Regular care will help preserve its appearance 1 2 Use only mild soap or detergent solutions Dry surfaces using soft cloth If hood looks splotchy stainless steel hood use an orange base cleaner to clean the surface of the hood Avoid getting cleaner on the control switches Spread a light coating over the surface of the hood and leave on
6. KORE KOBE Brand Range Hood Model No CX1830GS 8 30 CX1836GS 8 36 CX1842GS 8 42 CX 183 SERIES 4 HEIGHT STAND ALONE GLASS CANOPY WITH LED SCREEN INSTALLATION INSTRUCTIONS AND OPERATION MANUAL READ AND SAVE THESE INSTRUCTIONS CONTENTS INSTRUC IONS uuu ua aa nuca ean eite ood ate 1 COMPONENTSIOR PACKAGE a ie 3 INSTALLATION P 5 Preparations amas a amawata 5 Hood uyu n 6 OO 8 Isccanc latihe Conyers coss a CU op TO dede 8 FEU OPK nahaon 9 Dict Cover 100 a 9 Final Assemb 9 u boa ect et ed en ac de tne en es emus e eren toes dx eene 10 12 SPECTEIC AT MIO T 14 MEASUREMENTS S DEAGRAMS des 15 EU 10 CTR CURT DIAGRAM 18 ES 19 WARRANTY s et E oer ad
7. OBE Range Hoods as applicable Keep proof of purchase or original invoice handy for inspection If the range hood is sold by the original purchaser during the warranty period the new owner is protected until expiration of the original purchaser s warranty CONDITIONS The following conditions apply only in relation to the warranty expressly given in this certificate 1 This warranty applies only a within U S A and Canada b to range hoods used for PRIVATE SINGLE FAMILY USE if used for COMMERCIAL or MULTIPLE FAMILY USE or other purposes warranty will be 2 Repair of any fault to be provided under this warranty shall not be provided a if the identification number attached to the range hood has been altered rendered illegible or removed b if notice of the defect has not been given within the period applicable forfailure of light bulbs d for physical damage e for surfaces damaged by use of improper chemical cleaning agents f if the appliance has been i subject to misuse abuse negligence accident incorrect installation or failure to follow the operating instructions ii connected to improper inadequate or faulty electricity service or exhaust ducts or flues or operated using incorrect or contaminated lubricants 11 installed maintained or operated otherwise than in accordance with the instructions furnished by KOBE Range Hoods including the improper use of detergents bleaches or cleaners
8. d to the ductwork above 20 Use duct tape to make all joints secure and air tight Make sure pipe is in the groove of the plastic damper Refer to Figure 14 Figure 14 Duct Cover Installation 21 SKIP STEP 22 and 23 IF USING THE RECIRCULATING CONVERSION KIT YOU WILL NOT NEED THE DUCT COVER MOUNTING BRACKET Using references in Table 1 and measurements on page 17 mark the leveling point for duct cover mounting bracket 22 Secure the duct cover mounting bracket to the wall with two screws not provided Refer to Figure 15 Make sure all screws are tightened 23 Hook the inner duct cover onto the duct cover mounting bracket and release the outer duct cover to fit onto the hood as shown in Figure 15 and 16 Figure 15 Figure 16 Final Assembly 24 Rotate the oil container clockwise to install it Shown in Figure 17 25 Turn power ON in control panel Check all lights and fan operation 26 Make sure to leave this manual for the homeowner Figure 17 OPERATING INSTRUCTION This KOBE hood is equipped with five electronic controls with LED screen one powerful centrifugal squirrel cage with stainless steel filter two bright 12 volt 20 watt halogen lights and one oil container The five control buttons are Power Control On Off Auto Control Speed Control Low amp High Speed Light Control and Timer Control Refer to Figure 18 Timer Control Speed Control Power Control Light Control Auto Control Figure
9. e it started c The fire department has been called d You can fight the fire with your back to an exit What to Do If You Smell Gas Extinguish any open flame not try to turn on the lights or any type of appliance Open all doors and windows to disperse the gas If you still smell gas call the Gas Company and Fire Department right away CAUTION 1 For general ventilation use only Do not use to exhaust hazardous or explosive materials and vapors 2 reduce the risk of fire use only metal ductwork Sufficient air is needed for proper combustion and exhausting of gases through the flue chimney of fuel burning equipment to prevent back drafting 3 Follow the heating equipment manufacturer s guideline and safety standards such as those 4 published by the National Fire Protection Association NFPA and the American Society for 5 Heating Refrigeration and Air Conditioning Engineers ASHRAE and code authorities 6 Two installers are recommended because of the large size and weight of this hood Activating any switch may cause ignition or an explosion WARNING ELECTRICAL SHOCK HAZARD Can result in serious injury or 9 death Disconnect appliance from electric power before servicing If equipped the fluorescent light bulb contains small amounts of mercury which must be recycled or disposed of according to Local State and Federal Codes COMPONENTS OF PACKAGE Must keep all materia
10. en to house wires 10 Connect according to color black to black white to white and green to green and cap with wire connectors 11 Test the operation of the hood before moving on to the next step Make sure power is supplied to the hood 12 If venting outside skip to Step 19 Ductwork Installation Hecirculating Conversion Requires Purchase of Recirculating Kit Model No RD 0183 13 For the recirculating installation replace the duct cover mounting bracket with the T Box Using references in Table 1 and Measurement amp Diagrams on page 15 to mark the leveling line for the T Box Secure the T Box with 3 screws not provided to the wall Use duct tape to seal joints from plastic damper to T Box Recirculating Duct Cover will hook onto T Box Refer to Figure 13 Figure 13 14 Measure the distance from the top of the plastic damper to the ceiling and prepare a 7 round metal duct pipe with 4 shorter than measured distance 15 Use the prepared 7 round metal duct pipe to connect the T Box to the plastic damper Use duct tape to make all joints secure and air tight Make sure pipe is in the groove of the plastic damper Refer to Figure 14 16 Remove stainless steel filters and install the carbon filters Refer to Figure 20 17 Re attach the stainless steel filters 18 Skip to Step 21 Duct Cover Installation Ductwork Installation 19 Use 7 round aluminum or steel pipe to connect the plastic damper on the hoo
11. eparations before Installation NOTE TO AVOID DAMAGE TO YOUR HOOD PREVENT DEBRIS FROM ENTERING THE VENT OPENING Decide the location of the venting pipe from the hood to the outside Refer to Figure 1 straight short venting run will allow the hood to perform more efficiently Try to avoid as many transitions elbows and long run as possible This may reduce the performance of the hood Use duct tape to seal the joints between pipe sections f necessary prepare back wall frame with cross framing lumber for secure installation Using references in Table 1 and measurements on page 15 decide the level of the lumber Refer to Figure 2 Important peel protective film off the duct cover and the hood if any 5 7 ROUND PIPE Figure 1 Hood Installation CAUTION If required to move the cooking range to install the hood turn off the power in an electric range at the main electrical box SHUT OFF THE GAS BEFORE MOVING GAS RANGE 1 Peel protective film off duct cover and hood if any Pull out duct cover inner and outer from range hood Shown in Figure 3 Figure 3 2 Align glass canopy to hood body Shown in Figure 4 Attach the glass canopy to body with four hexagon screws and four spacers provided Tighten with hexagon wrench provided Shown in Figure 5 Figure 4 Figure 5 3 Attach the LED screen and control panel with two hexagon screws and two spacers provided Tighten with hexag
12. for a few minutes do not leave on too long or this may cause damage to hood finish Use soft towel to wipe off the cleaning solution gently rub away stubborn spots Use a slightly damp towel to get rid of any cleaning solution Use dry soft towel to dry the hood To bring glow back into a stainless steel finish use a stainless steel cleaner DO NOT allow deposits to remain for long periods of time DO NOT use ordinary steel wool or steel brushes Small bits of steel may adhere to the surface causing rust DO NOT allow salt solutions disinfectants bleaches or cleaning compounds to remain in contact with stainless steel for extended periods Many of these compounds contain chemicals which may be harmful Rinse with water after exposure and wipe dry with a clean cloth To Clean Stainless Steel Filter Oil Container CAUTION DRAIN OIL CONTAINER BEFORE OIL CAN OVERFLOW The oil container attached underneath stainless steel filter can be removed by turning counter clockwise To clean the stainless steel filter remove the screws leave in a safe place and slide stainless steel filter out Both oil container and stainless steel filter should be washed with warm soapy water and dry thoroughly before returning in place Both are top rack dishwasher safe 12 To Clean Carbon Filter Optional Recirculating Kit 1 Turn oil container counter clockwise Shown in Figure 18 2 Use a Philips screwdriver to take out the screws 2 pcs S
13. g fordamage to range hood during transit delivery installation or removal h for damage by or resulting from attempted repairs conducted by anyone other than our Authorized Service Agent 20 3 he purchaser shall be responsible for any expenses involved in making the range hood readily accessible for servicing and where the range hood is installed outside the main sales territory of the retailer or service territory of the nearest approved KOBE Range Hoods Agent as applicable for any traveling expenses and any costs of transporting the range hood or parts thereof to and from the dealer or Service Agent 4 The purchaser must produce proof of purchase together with this warranty certificate when making the claim 5 Damages caused during shipment are not covered under our warranty CONSEQUENTIAL DAMAGE The warrantor is not responsible for any consequential damage SOME STATES DO NOT ALLOW THE EXCLUSION OF CONSEQUENTIAL DAMAGE SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU IMPLIED WARRANTIES STATE LAW Any implied warranties including the implied warranty of merchantability and fitness for purpose imposed on the sale by the laws of the state of sale are limited to two year from the date of original purchase Some states do not allow limitations on the duration of implied warranties This warranty gives you specific legal rights and may also have rights which vary from state to state SERVICE For service contact KOBE Range Hoods
14. hown in Figure 19 V Figure 18 Figure 19 3 Remove the carbon filter from the two stainless steel filters Shown in Figure 20 4 Place carbon filter into warm water with neutral detergent and clean thoroughly Dry and replace 5 Re install the carbon filter and the stainless steel filters Aw Figure 20 To Replace Light Bulb CAUTION HALOGEN LIGHT UNIT MAY BE HOT WAIT UNTIL UNIT IS COOL 1 Make sure all control switches are off and range hood is unplugged Use a flat head screwdriver to pop out protective covering as shown in Figure 21 Gently pull out the defective light bulb and discard Light bulbs should be 12V 20W maximum Refer to Figure 22 Push bulb securely into light socket Replace protective cover 5 Plugin range hood 2 3 HALOGEN LIGHT FLAT HEADED BULB 12V 20W SCREWDRIVER Figure 21 Figure 22 13 SPECIFICATIONS MODEL SIZE COLOR CONSUMPTION VOLTAGE NUMBER OF MOTOR DESIGN FAN TYPE EXHAUST CONTROLS HALOGEN LIGHTS HOOD DIMENSION W x D x H DUCT COVER BLOWER DIMENSION W x D x H OPTIONAL ACCESSORIES W x D x H Weight Ibs SPEED AIR CAPACITY CFM SONE In House Test Static Pressure 0 183065 8 30 CX1836GS 8 36 184265 8 42 304 Commercial Grade Stainless Steel 189 4W 1 57A Wattage Ampere 120V 60Hz 1 18 Gauge Centrifugal Squirrel Cage 7 Round w Damper Electronic Touch Button 5 bu
15. l for returns or refunds Box 1 Of 2 A LED Screen And Control Panel Glass Canopy At Box 2 Of 2 A KOBE Range Hood with Two Piece Duct Cover B Duct Cover Mounting Bracket C Hood Mounting Bracket D Warranty Registration Card E Instructions Manual F Plastic Damper G Screws Package H Rubber Seal I Glass Canopy Screws Set 1 Oil Container Inner 1C Duct Cover At Outer Duct Cover E RORE KOBE Brand Range Hood Moris Ho CK132855 E CX 1E3 SERIES 4 HEIGHT GLASS CANOPY WITH LEO SEREEBF Lu be RETE iB a HERE a HIRE BISTALLATICH INSTRUCTIONS AND OPERATION MANUAL Hexagon screws 6 pc Spacer 6 pc Hexagon wrench 1 pc Safety Bracket 1 pc INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation To calculate installation please refer to Table 1 All calculation in inches TABLE 1 A Height of Floor to Ceiling B Height of Floor to Counter Top Standard 36 C Preferred Height of Counter to Hood Bottom Recommended 27 to 30 D Height of Hood E Height of the Hood Installation A B C F Height of Duct Cover E D SAFETY WARNING HOOD MAY HAVE VERY SHARP EDGES PLEASE WEAR PROTECTIVE GLOVES IF REMOVING ANY PARTS FOR INSTALLING CLEANING OR SERVICING Pr
16. nal property or real estate or any bodily injuries whether caused directly or indirectly by the range hood WARNING TO REDUCE THE RISK OF PERSONAL INJURY IN THE EVENT OF A RANGE TOP GREASE FIRE Keepfan filter if any and grease laden surfaces clean e Always turn hood ON when cooking at high heat Use high settings on cooking range ONLY when necessary Heat the oil slowly on low to medium setting Do not leave cooking range unattended when cooking Always use cookware and utensils appropriate for the type and amount of food prepared Use this unit only in the manner intended by the manufacturer Before servicing switch power off at service panel and lock service panel if possible to prevent power from switching on accidentally Clean ventilating fans frequently Grease should not be allowed to accumulate on fan or filter What to Do In The Event Of a Range Top Grease Fire SMOTHER FLAMES with a close fitting lid cookie sheet or metal tray and then turn off the burner KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES If the flames do not go out immediately EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911 NEVER PICK UP A BURNING PAN You may get burned DO NOT USE WATER including wet dishcloths or towels a violent steam blast will result Use extinguisher ONLY if a You have a Class A B C extinguisher and know how to operate it b The fire is small and contained in the area wher
17. od overseas because the power supply may not be compatible and it may violate the electrical code of that country Using KOBE hood overseas is at your own risk and will void your warranty kv 070307 23
18. on wrench provided Shown in Figure 6 Figure 6 4 Place rubber seal on hood venting area make sure the openings on rubber seal are aligned with openings in vent area Shown in Figure 7 Align plastic damper on rubber seal and attach to hood using eight 4x20 mm screws provided Refer to Figure 8 Figure 7 Figure 8 5 f necessary remove the two rubber stands at the back of the hood For a more secure installation KOBE recommends not removing the rubber stands 6 Using references in Table 1 and Measurement amp Diagrams on 15 mark the leveling line for hood mounting bracket Secure hood mounting bracket to wall with screws not provided Refer to Figure 9 Figure 9 7 Align hood to the hood mounting bracket on the wall and hook hood into place as shown in Figure 10 amp 11 CAUTION MAKE SURE THE HOOD IS SECURE BEFORE RELEASING Figure 10 Figure 11 8 For safety purposes install the safety bracket provided with one screw not provided to the wall as shown in Figure 12 Figure 12 Wiring to Power Supply A SAFETY WARNING RISK OF ELECTRICAL SHOCK THIS RANGE HOOD MUST BE PROPERLY GROUNDED MAKE SURE THIS IS DONE BY SPECIALIZED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES BEFORE CONNECTING WIRES SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALL Y 9 Connect three wires black white and gre
19. st be returned in good working condition with ALL original parts and documentation packed in ALL original cartons fillers and shipping cartons A restocking fee of 2596 will be charged for all approved return s EXCHANGES OR RETURNS MAY NOT BE ACCEPTED IF ANY PACKAGING IS MISSING 4 MAKE SURE TO INSPECT THE HOOD FOR DAMAGES AND DEFECTS BEFORE INSTALLATION Appearance flaws of the hood found after installation and not affecting hood performance is not covered under our warranty for returns or exchanges Service visits not covered under warranty will carry a service charge A Before Installation Return for exchange or refund please see above for acceptable returns B After Installation NO exchange or refund 19 WARRANTY WARRANTY CERTIFICATE KOBE Range Hoods Inc warrants all products manufactured or supplied by it to be free from defects in workmanship and materials Its obligations pursuant to this warranty are limited to a period of two years from the date of purchase and to the repair or replacement at its option and subject to the terms and conditions stated below of any component part which its examination shall disclose to be so defective TWO YEAR WARRANTY SERVICE PERIOD Any covered failure occurring within two years of original purchase arising from defective workmanship or material in manufacture will be repaired or at our option the unit will be replaced free of charge by an authorized KOBE Range Hoods Agent or K
20. ttons Power Control Auto Control Speed Control Low amp High Speed Light Control amp Timer Control 12V 20W x2 Model No CX1830GS 8 Model No CX1836GS 8 Model No CX1842GS 8 Model No 183 85 29 1 2 x 19 3 4 x 3 35 1 2 x 19 3 4 x 4 1 2 41 7 8 x 19 3 4 x 6 1 2 14 7 8 x 13 x 15 3 4 37 1 21 Inner Duct Cover Extension Model No CX183 21DC 14 1 8 x 13 x 15 3 4 x 37 2 30 Stainless Steel Back Panel Model No SSP30 30 x 1 10 x 32 3 36 Stainless Steel Back Panel Model No SSP36 36 x 1 10 x 32 4 Recirculating Kit Model No RD 0183 NET GROSS CX1830GS 8 9 14 CX1836GS 8 14 18 CX1842GS 8 16 22 CX183 8S 35 46 LOW HIGH 400 600 1 3 28 Specifications subject to change without notice 14 35 1 8 890 MAX MEASUREMENTS amp DIAGRAMS Inch figures converted from millimeters measurements Inch measurements estimated Millimeter measurements in 13 a Taa VIEWING DOWN FROM THE 35 7 8 910 2 3 16 55 gt S a Na m C 7 ROUND PIPE 13 16 21 DUCT COVER MOUNTING BRACKET PLASTIC DAMPER UE ENSE 8 13 16 224 HOOD MOUNTING BRACKET 15 16 1 15 16 5 50 50 2 eo 14 3 16 360 uei s G 35 3 8 900
Download Pdf Manuals
Related Search