BlueTrek G2 Consumer Headset
Contents
1. maximize battery capacity it is recommended to recharge your headset to full capacity only when the battery is low since a battery has a lifetime of about 500 charging cycles e If you leave your headset battery empty for an extended period of time it could excessively discharge the battery In this case charge your headset for 10 hours or more until the battery recovers and recharges completely Only switch on the headset once the red indicator light turns off indicating the battery has fully recovered e Do not let the battery charger remain plugged in the headset for more than 24h e The use of any other charger will automatically suspend the warranty Pairing the BLUETREK G2 Before using the BLUETREK Gz2 headset you must pair it with your Bluetooth mobile phone Pairing is the process of linking 2 Bluetooth devices so that they can communicate To initiate pairing PAGE 3 6 1 Place the BLUETREK G 2 and your mobile phone within 0 3 meter 1 foot from each other 2 Switch on your phone and select its Bluetooth discover mode refer to the Bluetooth mobile phone user manual 3 When the BLUETREK G 2 is switched off press and hold the TALK button for about 7 seconds until the indicator light flashes red and blue alternatively And a sound can be heard in the speaker 4 Once the mobile phone detects the headset a BlueTrek G2 message will be displayed Follow the phone instructions to accept the pairing Th2. off your headset and your mobile phone and switch them on again To find out more please refer to the trouble shooting frequent asked questions in our website www bluetrek com Guidelines for safe use Read those guidelines before using your headset Donotdrop or try to alter the shape of your Headset Donot expose your headset to liquid or moisture Do not expose your headset to extreme temperatures Temperature range 0 40C Donot expose your headset to fire or open flames Do not try to disassemble your headset Service and Maintenance can only be performed by authorized BLUETREK dealers Keep your headset away from dust and dirt Do not let children play with your headset since it contains small parts that could become detached and create a choking hazard Check the regulation in your area if you plan to use your headset while driving Turn off your headset before boarding an airplane CAUTION Danger of explosion if battery is incorrectly replaced Dispose of batteries according to local regulations Do not dispose as household waste PAGE 6 6
3. BLUETREK G2 user guide Thank you for choosing the BLUETREK G2 we hope you will enjoy the convenience we are bringing to you The BLUETREK G2 offers many functions please read this manual before getting started EC Declaration of Conformity We Innovi Technologies Ltd of 31 F China Online Centre 333 Lockhart Road Wan Chai Hong Kong declare under our sole responsibility that our product BLUETREK G2 to which this declaration refers is in conformity with the appropriate standards EN300 328 02 EN301 489 17 EN301 489 01 EN50371 EN60950 Following the provisions of Radio and Telecommunications Terminal Equipment directive 1999 5 EC October 2005 Guillaume Ponticelli Director of Development FCC Statement PAGE 1 6 This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Caution Changes or modifications to this Bluetooth headset not expressly approved by the party responsible for compliance could void the user s authority to operate it Industry Canada notice to users and product statements To prevent radio interference with the licensed service this device is intended for operated indoors and away from windows to provide maximum shielding Equipment or its transmit antenna that is installed outd
4. e PIN code or passkey is 0000 then press yes or ok If pairing success the indicator light will switch to blue and flashes slowly If you haven t started the discovery mode within5 minutes the headset will switch off You must then switch on your headset and start the pairing again Wearing the BLUETREK G2 The headset can be used on both ears Rotate the ear clamp if you want to use it on the other ear The ear clamp is made of soft material which can be easily shaped to fit your ear Make sure the speaker is properly inserted into your ear Switching the BLUETREK G2 ON and OFF Switching BLUETREK G2 ON When your headset is off press and hold the TALK button for about 2 seconds until the blue indicator light is on A beep 2 tones can be heard in the speaker Release the TALK Button To check if your headset is ON press once on the TALK button If the indicator light flashes blue it means your headset is ON Switching BLUETREK G2 OFF When your headset is on press and hold the TALK button for about 5 seconds until the red indicator light is on after the quick blue flashes A beep 2 tones can be heard in the speaker then release the TALK Button Making a call Mobile phone with voice recognition Make sure the voice recognition function on your mobile is activated and your voice tags have been recorded with the phone To enter these please refer to your phone s manual When there is no incomi
5. ng or active call press once on the TALK button Wait for the audio signal sent by the mobile phone generally a short tone Speak the name of person you wish to call Mobile without voice recognition Make sure both the headset and the mobile phone are ON and in stand by mode Dial the number on the phone keypad after approximately 2 seconds the audio connection will be established This function may not be available on some phones please refer to the trouble shooting frequent asked questions in our website www bluetrek com to find out more PAGE 4 6 Answering a call When the headset rings press once on the TALK button to take the call Ending a call Press once on the TALK button to end an active call Adjusting the volume To increase the volume during an active cal press the VOL button on the headset To decrease the volume during an active call press the VOL button on the headset Muting the microphone To mute the microphone during an active call During an active call pressand hold the VOL button fo r approximately 2 seconds A periodic tone can be heard in the speaker when the microphone is muted To end the mute function When the microphone is muted quickly press the VOL button on the BLUETREK G2 The periodic tone will end Transferring a call from BLUETREK G2 to the mobile phone During an active call press the TALK button for about 2 seconds This function only works in the Hand
6. oors is subject to licensing In compliance with Industry Canada regulations technical specifications have been provided in a declaration of conformity This does not imply that Industry Canada approved the equipment Bluetooth is a trademark owned by Bluetooth SIG Inc and is used by the manufacturer under license BEFORE USING YOUR HEADSET FOR THE FIRST TIME PAGE 2 6 You must charge it continuously for about 8 hours until the red indicator light turns off Please refer to the Charging the BLUETREK G2 section of this manual Pair the headset with a mobile phone Please refer to the Pairing BLUETREK G2 section of this manual Introduction The BLUETREK G2 headset is a wireless headset based on the Bluetooth technology It complies with Bluetooth 1 2protocol supporting Headset and Hands free profile The BLUETREK G2 headset has 3 buttons e TALK button main button e 1 VOL button e 1 VOL button Charging the BLUETREK G2 Please connect the charger to the headset and to the mains During the charge the indicator light is red The indicator light will turn offwhen the charge is complete During subsequent charges the charging should take approximately 2 hour 40 minutes When you hear a light beep in your headset at regular intervals andthe indicator light flashes in red your headset needs to be recharged Important e The headset cannot be operated while charging To
7. s Free Profile In the Headset profile you can simply turn off your headset Transferring a call from the mobile phone to the BLUETREK G2 To transfer the call back to the headset use the menu option on your phone Call waiting When you hear a call waiting alert while you are on a call press once on the TALK button to accept the second call This function may not be available depending on your phone s functionality However you can always answer the second call from your phone keypad Multi Pairing BLUETREK G2 can be paired to two mobile phones For instance Your headset is already paired with mobile phone A You then perform a pairing with mobile phone B All incoming calls on mobile phone A or B can be answered by BLUETREK G2 as long as the headset is on standby However you can only use mobile phone B i e the lastly paired phone for outgoing calls PAGE 5 6 Note This function is not available on some phones Please refer to the trouble shooting frequent asked questions in our website www bluetrek com to find out more Additional features with some phones Rejecting a call When the headset rings press the TALK button for about 2 seconds Redial the last number When there is no incoming or active call press the TALK button for about 2 seconds until you hear a beep Troubleshooting guide The first thing you should do when encountering a problem that you cannot solve with this manual is to switch
Download Pdf Manuals
Related Search