Electrolux Icon Professional Ice Maker Free Delivery
Contents
1. EXHAUST Figure 6 INTAKE Water Supply Connection 13 CONNECTING THE WATER SUPPLY When connecting the water supply follow these guidelines e Review the local plumbing codes before you install the unit e The water pressure should be between 20 and 120 psi A CAUTION If you are using a filter system you will need to have at least 20 psi for 3 minutes every 15 minutes e certain a SHUT OFF VALVE is installed in the 1 4 inch water supply line e Connect sufficient tubing to the unit to allow the unit to be moved for cleaning and servicing However make certain that the WATER tubing is not pinched or damaged during CONNECTION installation e Electrolux recommends the use of copper tubing for installation UL103_CO Figure 7 14 Water Supply Connection Figure 8 Figure 9 WATER LINE Figure 10 Locate the compression fitting and ferrule packed in the unit Slide the compression fitting and ferrule over the 1 4 inch water supply line Do not use thread sealing compound or tape Using two wrenches tighten the compression fitting on the supply line see Figure 8 Carefully bend the water supply line into position and connect the line to the solenoid valve see Figure 9 Avoid kinking the water supply line For recessed installations allow extra water supply line length to provide s2. Figure 19 CLRCOO08 18 Door Adjustment ADJUSTING THE DOOR Your door is aligned at the factory before shipment Occasional re adjustment may be necessary especially if an overlay panel is installed The following procedure will correct for up to 1 4 alignment The door should never be flush with the top of the cabinet Even when level the top edge of the door will be 1 8 below the top of the cabinet see Figure 21 To adjust Figure 21 1 Compare the top edge of the door opposite the hinges to the top edge of the cabinet and note the type up or down of adjustment needed Remove the top hinge pivot pin with a 7 64 hex wrench see Figure 22 and lift door off bottom hinge pin Be careful not to lose door closers see Figure 24 With door upside down loosen but do not remove the two hinge plate screws Figure 22 4 Door Adjustment 19 If door edge opposite the hinges needs to move up move plate toward outside of door If door edge needs to move down move plate toward inside of door see Figure 23 Repeat until top edge of door is parallel with top of cabinet and tighten screws securely After adjustment is complete remove the door closers from the bottom hinge clean thoroughly and apply petroleum jelly to the mating surfaces of the closers see Figure 24 Be sure that bosses on closers align with holes in hinge and hinge plate Mount door and install top hinge pivot pin
3. Figure 23 S SLOTTED MOUNTING HOLES NOTCH er RAISE gt LOWER OUTSIDE OUTSIDE DOOR EDGE DOOR EDGE CLRCOO01a Figure 24 4 Finding Information TABLE OF CONTENTS Finding Information sssscssseseeseeeseeeeeeeees 2 Built in Installation 20 Please Read And Save This Guide 2 Make A Record For Quick Reference 2 Start up ih nh nn hin ni i onc an cn a 21 Warranty Registration Normal Operation 22 QUESTIONS eee 3 Ice Cube 22 Table OF COMMS iia 4 Ice Dispsenser Operation and Care 23 Safety r 5 coecceeccsccccsecccseccoseccessocsecccsecessecceseceee 25 Important Safety Instructions 5 Special Considerations 25 Installation sss 7 Maintaining and 25 Installation Dimensions 7 Exterior Cleaning 25 Drain Installation vo 8 Stainless Steel Models 25 Interior Cleaning 26 Drain Pump 10 Condenser Cleaning 27 Self T 28 Site Prepara
4. N Use amp Care Guide lce Maker 4 Electrolux 5995421640 2 Finding Information PLEASE READ AND SAVE THIS GUIDE Thank you for choosing Electrolux the new premium brand in home appliances This Use amp Care Guide is part of our commitment to customer satisfaction and product quality throughout the service life of your new ice maker We view your purchase as the beginning of a relationship To ensure our ability to continue serving you please use this page to record key product information IMPORTANT PLEASE READ all instructions completely before attempting to install or operate the unit All ice makers require a connection to both a water supply and an electrical power source Improper hook up can result in substantial property damage Proper installation in accordance with the manufacturer s specifications and all local codes is the sole responsibility of the consumer The manufacturer is not responsible for any installation expenses or damages incurred due to improper installation If you are unsure of your ability to safely make electric power water supply and water drain connections to the unit consult licensed and insured professionals to perform all electrical and plumbing work Once you have your unit installed we suggest you keep this manual in a safe place for future reference Should any problems occur refer to the Troubleshooting section of this manual This information will help you
5. any given batch will vary choose cubes from the sample area for comparison when making adjustments see Figure 31 The factory setting is 0 Ice Cube Mold 4 Reinstall the front access cover SAMPLE AREA 5 Reconnect power to icemaker TS T Kr Figure 31 Maintenance 25 SPECIAL CONSIDERATIONS e For best performance keep the unit out of direct sunlight e Turn the unit OFF and dispose of any ice cubes if the unit will be used for 5 days or more Prop door open to allow for air circulation and prevent mold and mildew e ambient temperature is expected to drop below 45 F 7 C drain all water from the unit to prevent freezing damage not covered by the warranty e High ambient temperatures 110 F 43 or higher may reduce the units ability to reach low temperatures and may also reduce the ice production rate MAINTAINING AND CLEANING YOUR ICEMAKER Periodic cleaning and proper maintenance will ensure efficiency top performance and long life The maintenance intervals listed are based on normal conditions You may want to shorten the intervals if you have pets or other special considerations Exterior Cleaning As Required The door grille and cabinet may be cleaned with a mild detergent and warm water solution Do not use solvent based or abrasive cleaners Use a soft sponge and rinse with clean water Wipe with a soft clean towel to preve
6. in the U S and Canada 1 877 4ELECTROLUX 1 877 435 3287 For online support and Internet product information www electroluxusa com IMPORTANT SAFETY INSTRUCTIONS Safety Precautions Do not attempt to install or operate your unit until you have read the safety precautions in this manual Safety items throughout this manual are labeled with a Danger Warning or Caution based on the risk type Definitions This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death A DANGER DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury A WARNING WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury A CAUTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury product damage or property damage IMPORTANT Indicates installation operation or maintenance information which is important but not hazard related 6 Safety General Precautions A DANGER RISK OF CHILD ENTRAPMENT Before you throw away your old appliance take off the doors and leave shelves in place so that children may not easily climb inside A WARNING e Never attempt to repair or perform maintenance on the unit until the electricity has been dis
7. incomplete e Incorrect incoming water e Water pressure must be 20 120 psi pressure e Unitis not level See Leveling the Unit Water leaking from under the unit s Supply line leaking e Check to see that the water inlet line is attached to inlet valve properly See Connecting the Water Supply Fill tube leaking e Check connection at water valve outlet e Bin drain leaking e Check integrity of bin drain hose and clamp Ice storage bin full of water e Obstructed drain Check to see that storage bin drain opening is free from obstruction and debris IF SERVICE IS REQUIRED If the need for service arises contact the dealer from whom the unit was purchased State the Model Number and Serial Number and explain the problem The Model and Serial Number plate is located inside the unit at the upper right hand corner If you do not know the name of the selling dealer or local service company you can check online at www electroluxusa com or call 877 435 3287 Warranty Information 33 ICE MAKER WARRANTY Your ice maker is protected by this warranty WARRANTY THROUGH OUR AUTHORIZED SERVICERS THE CONSUMER WILL BE PERIOD WE WILL RESPONSIBLE FOR FULL ONE YEAR One year from Pay all costs for repairing or replacing any parts of this Costs of service calls that are listed under WARRANTY original purchase appliance which prove to be defective in materials or NORMAL RESPONSIBILITIES OF THE date workmanship CONSUME
8. not recommended 5 Reconnect inlet and outlet lines to the water valve Replace back panel Drain water from the water trough and drain line by removing the overflow tube see Figure 34 Clean the ice maker and storage bin before next use 9 Prop door open to allow for air circulation and prevent mold and mildew IMPORTANT It is possible that dirt or scale will dislodge in the water line Always throw away all ice cubes made during the first 24 hours of operation when the unit is returned to service Troubleshooting 31 BEFORE YOU CALL FOR SERVICE If the unit appears to be malfunctioning read through Normal Operation first If the problem persists check the Troubleshooting Guide Locate the problem in the guide and refer to the cause and its remedy before calling for service The problem could be something very simple which can be solved without a service call TROUBLESHOOTING GUIDE A DANGER ELECTROCUTION HAZARD NEVER attempt to repair or perform maintenance on the unit until the main electrical power has been disconnected Troubleshooting What to check when problems occur Problem Possible Cause Remedy Unit does not operate e No electrical power to the unit Make sure power cord is plugged in Check for blown fuse or tripped circuit breaker Cycle selector switch set e Make sure cycle selector switch is set to ICE ON improperly Surrounding air temperature must be at least e Low air temper
9. quickly identify a problem and get it remedied In the event you require assistance please contact the dealer where you purchased your unit MAKE A RECORD FOR QUICK REFERENCE Whenever you call to request information or service you will need to know your model number and serial number You can find this information on the serial plate located on the inside wall of your unit and on the product registration card 2004 Electrolux Home Products Inc Post Office Box 212378 Augusta Georgia 30917 USA All rights reserved Printed in the USA Finding Information 3 PRODUCT REGISTRATION CARD The package containing this manual also includes your product registration information Warranty coverage begins at the time your Electrolux ice maker was purchased NOTE Registering your product with Electrolux enhances our ability to serve you You can register online at the Internet address below or by dropping your Product Registration Card in the mail Complete and mail the Product Registration Card as soon as possible to validate the registration date Please record the purchase date of your Electrolux unit and your dealer s name address and telephone number Purchase Date Electrolux Model Number Electrolux Serial Number Dealer Name Dealer Address Dealer Telephone Keep this manual and the sales receipt together in a safe place for further reference QUESTIONS For toll free telephone support
10. R LIMITED 219 57H Second through fifth Repair or replace any parts in the cabinet liner or sealed Costs for pickup and delivery of the appliance YEAR WARRANTY years from original refrigeration system compressor condenser evaporator required because of service Costs for labor parts Cabinet Liner and purchase date dryer or tubing which prove to be defective in materials or and transportation other than with respect to the Sealed System workmanship cabinet liner or sealed refrigeration system LIMITED Time periods listed All of the provisions of the full warranties above and the Costs of the technician s travel to the home and any WARRANTY above exclusions listed below apply costs for pick up and delivery of the appliance Applicable to the required because of service State of Alaska In the U S A your appliance is warranted by Electrolux Home Products Inc We authorize no person to change or add to any of our obligations under this warranty Our obligations for service and parts under this warranty must be performed by us or an authorized Electrolux Home Products Inc servicer In Canada your appliance is warranted by Electrolux Canada Corp NORMAL This warranty applies only to products in ordinary household use and the consumer is responsible for the items RESPONSIBILITIES listed below OF THE CUSTOMER 1 Proper use of the appliance in accordance with instructions provided with the product 2 Proper instal
11. ature around unit 45 F 7 C Unit runs but no ice is produced e No water being supplied to the Check to see that water is connected and turned unit on to the unit Unit runs but produces very little ice e Dirty condenser coils e Clean the condenser See Maintenance e High air temperature around unit Surrounding air temperature of over 90 F 32 C Low ice production at high temperatures is normal s Scale and mineral buildup in unit s Clean unit See Maintenance Inadequate airflow at the front of e Remove items blocking airflow the unit Ice is slow to release or does not e Ice making system is dirty e Run unit through automatic clean cycle See release from the evaporator Maintenance e Unitis not level e See Leveling the Unit e Low air temperature around the unit e Surrounding air temperature must be at least 50 F 10 C 32 Troubleshooting Troubleshooting What to check when problems occur Problem Possible Cause Remedy Poor ice quality soft or unclear e Poor incoming water quality Consult a qualified plumber to test the water quality and recommend appropriate treatment e Ice making system is dirty Run unit through automatic clean cycle See Maintenance Unit produces shallow or e Low water level Check to see that overflow tube is fully seated incomplete cubes or the ice fill Hot incoming water Connect the unit to a cold water supply See pattem on the evaporator is Installation
12. connected e Altering cutting of power cord removal of power cord removal of power plug or direct wiring can cause serious injury fire and or loss of property and or life and will void the warranty e Do not lift unit by door handle A CAUTION Use care when moving the unit Some edges are sharp and may cause personal injury Wear gloves when moving or repositioning the unit Never install the unit behind closed doors Be sure front grille is free of obstruction Obstructing free air flow can cause the unit to malfunction and may void the warranty Allow unit temperature to stabilize for 24 hours before use Never use an ice pick or other sharp instrument to help speed up defrosting These instruments can puncture the inner lining or damage cooling unit Failure to clean the condenser every three months can cause the unit to malfunction This could void the warranty A CAUTION e Using a heater to speed up defrosting can cause personal injury and damage to the inner lining DO NOT use any type of heater to defrost Use only genuine Electrolux replacement parts Imitation parts can reduce ice rate cause water to overflow from ice maker mold damage the unit and may void the warranty Installation 7 INSTALLATION DIMENSIONS 14 15 16 Raa gt 5 12 7 WATER ANE EE a 21 314 OUTLET a a Figure 1 3 Drain Installation INSTALLING THE DRAIN A CAUTION PLEASE READ all instruc
13. e connect the water supply line to the water solenoid valve Tighten connector securely Open the water supply valve and check for leakage at the water connection Make sure the water supply line is not kinked 7 Reconnect power to the unit before re installing UL103_CO 8 sure the drain system is working properly and the drain hose is not pinched or kinked Pour one gallon of cool fresh water into the ice bin The water should drain freely If your ice maker is equipped with a drain pump the pump should drain the ice bin 30 Storage Vacation and Moving DRAINING FOR NON US If the unit is to be stored moved or not used for extended periods it will be necessary to drain the system of water A WARNING Electrical Shock Hazard Disconnect power before servicing Before operating replace all panels Failure to do so can result in death or electrical shock 1 Disconnect power from the unit 2 Remove ice from the storage bin 3 Shut off water supply at the main water source NOTE Back panel must be removed prior to disconnecting the water lines 4 Disconnect the inlet and outlet lines to the water valve and allow them to drain A CAUTION If the ambient temperature is expected to drop below 45 F 7 C drain all water from the unit to prevent freezing damage which is not covered by the warranty IMPORTANT The use of anti freeze or other products of this nature is not necessary and is
14. e evaporator Remove all ice from the storage bin Remove inside front cover see Figure 33 Figure 33 Maintenance 29 4 Remove the overflow tube by lifting it up while using a slight back and forth motion to loosen it from the drain hole see Figure 34 The water in the reservoir will flow down the drain 5 Replace the overflow tube after all of the water has drained from the reservoir Move the cycle selector switch to the CLN position 7 When water begins to flow over the evaporator approximately 3 minutes add one package of Electrolux Ice Machine Cleaner to the water reservoir Reinstall inside front cover UL209a 9 When the self cleaning process stops approximately 45 Figure 34 minutes it may be desirable to clean the storage bin at this time see Interior Cleaning 10 Move the cycle selector switch to the ICE ON position to resume ice production Inlet Screen Cleaning Every Year The solenoid valve inlet screen must be cleaned at least once each year as follows Shut off the water at the water supply valve Fi 95 igure 2 Pull the unit out to access the back panel see A Figure 35 WATER CONNECTION 3 Disconnect electrical power to the unit 4 Disconnect the entire hose connector from the water solenoid valve see Figure 35 5 Use a tooth brush to clean sediment from the inlet screen DO NOT remove the screen 6 R
15. e the Electrolux EIMP60 drain pump or a pump with the above listed specifications could result in substantial water leakage and pooling with severe and costly water damage and related consequential damages and harm Site Preparation 11 PREPARING THE SITE IMPORTANT It is extremely important that the unit is level If it is not level the ice mold will not fill evenly This can cause a reduction in ice rate uneven sized cubes or water spilling into the storage area which will cause the ice in the bin to melt pre maturely Remember that floors near drains have a tendency to slope towards the drain 1 Position the unit on a flat level surface capable of supporting the entire weight of the unit Remember that the unit will be significantly heavier once it is fully loaded 2 The surrounding air temperature must be at least 50 F 10 C but must not exceed 110 F 43 C 3 The unit must not be located near heat generating equipment or in direct sunlight A DANGER ELECTROCUTION HAZARD Electrical Grounding Required This appliance is equipped with a three prong grounding polarized plug for your protection against possible shock hazards NEVER remove the round grounding prong from the plug e NEVER use a two prong grounding adapter NEVER use an extension cord to connect power to the unit Where a two prong wall receptacle is encountered or a longer power cord is required contact a qualified electrician to have it replac
16. ed in accordance with applicable electrical codes 4 The unit must be located to allow clearance for water drain and electrical connections in the rear of the ice maker 5 Connect the unit to a grounded and polarized 115 VAC 60 Hz 15 A circuit normal household current 6 Avoid connecting the unit to a Ground Fault Interruptor GFI GFls are prone to nuisance tripping which will cause the unit to shut down GFIs are generally used on circuits which power equipment that must run unattended for long periods of time 7 The unit must be installed according to your local codes and ordinances 12 Site Preparation NOTE The door of the unit may be mounted on either side of the cabinet see REVERSING THE DOOR All units require zero clearance when installed flush with a cabinet or wall see Figure 4 Electrolux stainless steel models require a minimum 2 3 4 inch handle clearance when installed against a wall or cabinet that extends beyond the front edge of the unit see Figure 5 6 Install and connect the water supply line See Z Connecting the Water Supply for installation CABINET requirements C yf 7 Position the unit to allow free air flow through the 22 front grille see Figure 6 8 Wipe out inside of unit with a damp cloth CLEARANCE NEEDED UL124A Koad Figure 4 ste 1 gt lt 2 314 uoo CLEARANCE NEEDED 1 1 Figure 5
17. el of ice reaches the top of the storage bin the unit shuts off As the ice level in the bin drops the unit will automatically restart to keep the bin full Your unit s ice production rate may vary depending on many considerations Ambient air temperatures water temperatures condenser cleanliness and ice maker cleanliness are all contributing factors to how quickly the unit produces ice Certain sounds are normal during the unit s operation You may hear the compressor or fan motor the water valve the water circulation pump or ice dropping into the ice storage bin Ice Cube Thickness Your Electrolux ice maker uses advanced technology to make ice that is crystal clear This technology cascades a flow of water over a chilled ice mold that is mounted vertically so no water sits in it Because of this ice making technology clear ice cubes differ significantly from regular ice cubes Differences are illustrated in Figure 27 e Dimples Electrolux clear ice cubes have dimples on one side from the lt gt Figure 27 cascading water process e Cube Variations Cubes made from different batches or even cubes within the same batch may have 7 varying dimples thickness and or sizes due to the cascading water process ICE BRIDGE Cube slabbing Electrolux clear ice makers produce a slab of ice that falls from the vertical mold relying on gravity to break the ice bridges Depending on the control
18. er fins are SHARP The fins can also be easily damaged A CAUTION DO NOT use any type of cleaner on the condenser unit 3 Clean the condenser coil using a brush with a combing action or a vacuum cleaner Do not touch the condenser coil 4 Position the grille to align the screw holes with the cabinet 5 Insert the grille screws and tighten Do not over tighten 28 Maintenance Self Cleaning Every 6 Months To maintain operational efficiency clean the unit every six months depending on water conditions more or less frequent cleaning may be necessary If the ice maker requires more frequent cleaning consult a qualified plumber to test the water quality and recommend appropriate treatment A WARNING Wear rubber gloves and safety goggles and or face shield when handling Ice Machine Cleaner A CAUTION Use only Electrolux Ice Machine Cleaner part number EIM30046 It is a violation of Federal law to use this solution in a manner inconsistent with its labeling Use of any other cleaner can ruin the finish of the evaporator and will void the warranty Read and understand all labels printed on the package before use Ice machine cleaner is used to remove lime scale and other mineral deposits Refer to the following steps for mineral deposit removal A CAUTION Never use anything to force ice from the evaporator Damage may result 1 Set the cycle selector switch to OFF and allow the to melt off of th
19. lack for easy removal from the recessed area see Figure 10 This will also safeguard against kinking the line A CAUTION After completing the installation turn on the water and recheck water and drain connection for leaks Apply additional tightening if needed Do NOT use thread sealing com pound or tape Plug in the power cord Gently push the unit into position If desired the unit may be recessed into cabinet or wall Allow at least 1 1 2 inches clearance behind the unit for electrical water supply and drain connections Leveling 15 LEVELING THE UNIT IMPORTANT It is extremely important that the unit is level If it is not level the ice mold will not fill evenly This can cause a reduction in ice rate uneven sized cubes or water spilling into the storage area which will cause the ice in the bin to melt pre maturely Remember that floors near drains have a tendency to slope towards the drain 1 Use a level to check the levelness of the ice maker from front to back and from side to side see Figure 11 2 Ifthe ice maker is not level adjust the feet on the corners of the unit as necessary see Figure 12 3 Check the levelness after each adjustment and repeat the previous steps until the unit is level Figure 11 Figure 12 TURN FOOT TO ADJUST 16 Door Reversal REVERSING THE DOOR SOME MODELS Figure 13 Figure 15 All Electrolux units may be left
20. lation by a licensed and insured professional in accordance with instructions provided with the appliance and in accordance with all local plumbing electrical and or gas codes 3 Proper connection to a grounded power supply of sufficient voltage replacement of blown fuses repair of loose connections or defects in house wiring 4 Expenses for making the appliance accessible for servicing such as removal of trim cupboards shelves etc which are not a part of the appliance when it was shipped from the factory 5 Damages to finish after installation 6 Replacement of light bulbs and or fluorescent tubes on models with these features EXCLUSIONS This warranty does not cover the following 1 CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY Note Some states do not allow the exclusion or limitation of incidental or consequential damages so this limitation or exclusion may not apply to you 2 Service calls which do not involve malfunction or defects in workmanship or material or for appliances not in ordinary household use The consumer shall pay for such service calls 3 Damages caused by services performed by servicers other than Electrolux Home Products Inc Electrolux Canada Corp or its authorized servicers use of parts other than genuine Electrolux Home Products parts obtained from persons other than such servicers or external ca
21. n the door and remove any ice from the storage bin 3 Wipe down the interior and storage bin with a solution of non abrasive mild soap or detergent and warm water Rinse with clean water 4 Sanitize the bin with a solution of 1 tablespoon of bleach in 1 gallon of warm water Rinse thoroughly with clean water 5 Check that all drain connections are in place A CAUTION 6 DO NOT use solvent cleaning agents or abrasives the interior These cleansers may transmit taste to the ice cubes or damage or discolor the interior DO NOT use any cleaner on the evaporator plate other than Ice Machine Cleaner Other cleaners may affect ice quality or cause damage to the unit that is not covered under warranty See AUTOMATIC CLEAN CYCLE for more information Reconnect power to the unit Maintenance 27 Condenser Cleaning Every 3 Months To maintain operational efficiency clean the condenser every three months depending on environmental conditions more or less frequent cleaning may be necessary A WARNING Disconnect electric power to the ice maker before cleaning the condenser To remove and replace the grille for access to the condenser fins follow this procedure see Figure 32 1 Remove the screws at each end of the grille 7 CONDENSER 2 Remove the grille Figure 32 A WARNING DO NOT touch the condenser fins The condens
22. ns may have loosened during shipment A WARNING To prevent accidental electrocution make certain that the floor surfaces surrounding the unit are dry whenever power is removed from or applied to the unit Drain Installation 9 1 certain the unit is not plugged into an electrical outlet 2 Carefully push the power cord grommet through the hole in the back panel See Figure 2 Remove 12 screws and back panel 4 Check that the clamps and hose connections are tight at the following areas illustrated in Figure 3 e Discharge tube A e Drain tube e Vent tube GROMMET 5 Place a suitable container beneath the pump s discharge Figure 2 tube Container must be able to hold a minimum of one gallon of water BACK VIEW SIDE VIEW UL184 2 Figure 3 A WARNING Back panel serves as a guard DO NOT put your hands inside the ice maker cabinet or attempt to touch any components except the discharge tube during testing Failure to follow this warning could result in serious personal injury or death 6 Plug the ice maker power cord into a properly grounded polarized electrical outlet 7 Verify pump operation by pouring one gallon of water into the ice storage bin of the ice maker The pump should energize and pump the water into the container 8 Atthis time verify that all tube and clamp connections a
23. nt water spotting Stainless Steel Models e Stainless steel models may discolor when exposed to chlorine gas pool chemicals salt water or cleaners with bleach e Keep your stainless unit looking new by cleaning with a high quality all in one stainless steel cleaner polish on a monthly basis Frequent cleaning will remove surface contamination that could lead to rust Some installations will require cleaning on a weekly basis 26 Maintenance DO NOT CLEAN WITH STEEL WOOL PADS DO NOT USE CLEANERS THAT ARE NOT SPECIFICALLY INTENDED FOR STAINLESS STEEL this includes glass tile and counter cleansers If any surface discolors or rusting appears clean it quickly with Bon Ami or Barkeepers Friend Cleanser and a non abrasive cloth Always clean in the direction of the grain Always finish this process with a high quality all in one stainless steel cleaner polish to prevent further problems USE OF ABRASIVE PADS SUCH AS SCOTCHBRITE WILL CAUSE THE GRAINING IN THE STAINLESS TO BECOME BLURRED Rust that is allowed to linger can penetrate into the surface of the stainless steel and become impossible to remove A CAUTION Stainless steel models exposed to chlorine gas and moisture such as areas with spas or swimming pools may have some discoloration of the stainless steel Discoloration from chlorine gas is normal Follow exterior cleaning instructions Interior Cleaning As Required 1 Disconnect power to the ice maker 2 Ope
24. or right hand opening The door opening is easily reversed by moving the hinge hard ware to the opposite side see Figure 13 To reverse the door 1 Remove top hinge screw pin 7 64 Allen wrench from cabinet see Figure 14 Remove door by tilting forward and lifting off bottom hinge pin 2 Remove plastic screw plugs 3 top and 3 bottom from new hinge location see Figure 15 and remove hinge pin hole plug in top of door see Figure 16 Do not discard Figure 16 Door Reversal Remove top hinge 3 screws reinstall hinge screw pin and remount on opposite side BOTTOM see Figure 17 Remove the two door closer inserts from the existing bottom hinge and install as shown on the new bottom hinge see Figure 18 Remove existing bottom hinge 3 screws and remount on opposite side TOP Remove hinge screw pin With bottom of door facing up remove pivot plate 2 screws flip over and remount on opposite side of door see Figure 19 Holding door upright with top of door tilted forward place hole of door pivot plate on bottom hinge screw pin see Figure 20 Be sure that the bosses on the closers align with holes in hinge and hinge plate Tilt top of door into position in top hinge and install top hinge screw pin In empty hinge holes install plastic screw plugs 3 top and 3 bottom and door hole plug 1 door top removed in step 2 17 HINGE _ SCREW Figure 17 INSERTS
25. re tight and leak free Unplug unit power cord from electrical outlet 10 Reinstall back panel 11 Continue to the next step in the installation process Site Preparation UL184 1 10 Drain Pump Connection CONNECTING A DRAIN PUM If a gravity drain connection is not available and you have not purchased the E15IM60E with factory installed pump we strongly recommend the use of the Electrolux EIMP60 drain pump The Electrolux EIMP60 drain pump is available through your Dealer or direct from Electrolux with complete installation instructions If a pump other than the Electrolux EIMP60 drain pump is to be used it must meet the following specifications e It must be UL listed and have a UL listed 120 VAC 3 wire grounded power cord e It must have overall maximum outside dimensions of 8 3 4 wide x 5 3 4 deep x 7 3 4 high e It must have a minimum flow rate of 15 gallons per hour at 10 feet of lift e It must have a sealed sump which does not allow water leakage in the case of a power outage restricted drain or pump failure e It must have a check valve the discharge line to prevent waste water return to the pump e It must have an overflow protection control which will shut off power to the ice maker in the event of a pump failure e It must have an operating temperature range of 50 F to 110 F 10 C to 43 A CAUTION In the event of a power outage restricted drain or pump failure the failure to us
26. setting and the fullness of the ice bucket it maybe necessary to tap the ice slab with the ice scoop to break it apart Operation 23 ICE DISPENSER OPERATION amp CARE The ice cube thickness control is factory set for best overall performance The factory setting is designed to maintain an ice bridge of approximately 1 16 to 1 8 under normal conditions resulting in a ae uaa TOO THIN TOO THICK dimple of approximately 1 4 to 1 2 ICEBRIDGE 00 DEEP C NO DIMPLE in depth see Figure 28 A fuller cube with less of a dimple results in a thicker ice bridge As the ice bridge becomes thicker the tendency for the cubes to stay together as a slab increases A bridge thicker than 1 8 may cause cubes to over fill the ice bucket Figure 28 A WARNING Disconnect power to the ice maker before making any ice thickness adjustments To adjust Figure 29 1 Disconnect power to the unit 2 Remove the screws securing the front access panel see Figure 29 24 Operation 3 Locate the cube thickness adjustment dial on the control board see Figure 30 Turn the dial clockwise number or counterclockwise number to thin the ice bridge Figure 30 ICE CUBE THICKNESS ADJUSTMENT DIAL IMPORTANT Ice thickness adjustment dial can be rotated 1 4 to 1 2 turn on the number dial Allow the ice maker to stabilize for 24 hours before making further adjustments Since ice cubes in
27. tion 11 Inlet Screen 29 Water Supply Connection 13 Storage Vacation and 30 Leveling arsanet 15 Troubleshooting 31 Door Reversal 16 If Service Is Required err 32 Door Adjustment ssssssssssssessssssesessssssseessseens 18 Warranty Information 33 20 Built In Installation Figure 25 INSTALLING A BUILT IN Your Electrolux product has been designed for either free standing or built in installation When built in your ice maker does not require additional air space for top sides or rear However the front grille must NOT be obstructed A CAUTION Do not install unit behind closed doors Built in Cabinet Dimensions Unit Dimensions see Figure 25 E15IM60E 14 15 16 34 1 8 ease unit installation and removal the unit must be located to allow clearance for water drain and electrical connections in the rear of the ice maker Start up 21 INITIAL START UP Once installation and leveling is complete the unit is ready for initial start up and operation Your unit is shipped in the OFF position however you may turn it ON OFF using the cycle selector switch located in the access panel above the grille see Figure 26 1 Plug the appliance cord into a 115V polarized and Figure 26 gro
28. tions completely before attempting to install or operate the unit All ice makers require a connection to the water supply and improper hook up can result in substantial property damage All water and drain connections MUST BE made by a licensed qualified plumbing contractor Failure to follow recommendations and instructions may result in damage and or harm A CAUTION Plumbing installation must observe all state and local codes All water and drain connections MUST BE made by a licensed qualified plumbing contractor Failure to follow recommendations and instructions may result in damage and or harm Model E15IM60E can be installed using a gravity drain or can use a factory installed or equivalent drain pump Follow these guidelines when installing drain lines to prevent water from flowing back into the ice maker storage bin and or potentially flowing onto the floor causing water damage Gravity Drain e Drain lines must have a 5 8 inch inside diameter e Drain lines must have a 1 inch drop per 48 inches of run 1 4 inch per foot and must not create traps e The floor drain must be large enough to accommodate drainage from all drains e Insulate the bin drain line to prevent condensation Ice Makers With Factory Installed Drain Pump A CAUTION Before installing an icemaker with a factory installed pump it is extremely important to check and test all hose connections at the drain pump There is a possibility that hose connectio
29. unded electrical outlet Open the water supply valve in the main water source 3 Place the cycle selector switch in the ON position The water fill valve will energize and fill the water reservoir CYCLE The water fill valve shuts off after 180 seconds The compressor begins to operate and water flows over the evaporator assembly ice cube tray 4 initial start up water flow over the evaporator may be uneven This may cause uneven sized cubes or water spilling into the ice storage bin This is a normal situation and will correct itself within the first 24 hours of operation After the initial start up period the water will cascade evenly over the evaporator IMPORTANT It is possible that dirt or scale will dislodge in the water line Always throw away all ice cubes made during the first two to three hours of operation 22 Operation NORMAL OPERATION The ice maker is designed to make clear ice from most water sources on a consistent basis Water is constantly circulated over the evaporator assembly As the water freezes gravity causes any sediment to drop into the water trough and not become imbedded in the ice This gives a clearer ice cube with a low mineral content When the ice reaches the desired thickness it falls off the evaporator and into the storage bin The cycle is then repeated When the lev
30. uses such as abuse misuse inadequate power supply or acts of God 4 Products with original serial numbers that have been removed or altered and cannot be readily determined IF YOU NEED SERVICE Keep your bill of sale delivery slip or some other appropriate payment record The date on the bill establishes the warranty period should service be required If service is performed it is in your best interest to obtain and keep all receipts This written warranty gives you specific legal rights You may also have other rights that vary from state to state Service under this warranty must be obtained by contacting Electrolux Home Products Inc or Electrolux Canada Corp This warranty only applies in the 50 States of the U S A and Puerto Rico and Canada Product features or specifications as described or illustrated are subject to change without notice All warranties are made by Electrolux Home Products Inc In Canada your appliance is warranted by Electrolux Canada Corp USA Canada 877 435 3287 866 213 9397 Electrolux Home Products Inc Electrolux Canada Corp 6150 McLaughlin Road Mississauga Ontario L5R 462 P O Box 212378 Augusta GA 30917
Download Pdf Manuals
Related Search