Hoover U5347-900 Upright Vacuum
Contents
1. NS AK Remove tape and remove dirt cup from Slide handle onto cleaner body Push bolts into holes on back of handle cleaner body Switch A should be in OFF position Continued 3 Place nuts in recessed areas on Place bottom of cup into cleaner Position cord on back of cleaner as front of handle Hold each nut in Pivot cup and snap in place shown and press cord into clip place while tightening each bolt securely with a Phillips screw driver Attach hose Note Hose must be connected as shown for all operations Align end of hose with projections A over slots B in dirt duct Slide hose into duct B and twist Lift hose tube cover C hose to lock it into place Position hose over hose hook D and into hose tube E Position tools a VE Nt SR f WU i Place smaller unridged end of wand Snap ends of dusting brush A into bottom of rack Snap wand into crevice tool B and furniture nozzle clip Repeat with other wand C into clips as shown Cleaner description Polarized plug To reduce the risk of electric shock this appliance has a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install the proper outlet Do not change the plug in any way2. 1 Handle 13 Dusting brush 2 Cord hooks wrap cord 14 Crevice tool around hooks for storage 15 Furniture nozzle The top hook rotates right 16 Hose hook re 17 Dirt cup latch 3 Hose f 18 Dirt cup lid 4 ON OFF switch located 13 pint cup on left rear corner of 20 Dirt cup handle cleaner body 21 Main filter inside 5 Carrying handle cup 6 Stair cleaning handle 22 Pre filter assembly located on lower edge of inside cup dirt cup 7 Handle release lever step on lever to lower handle to operating or low positions 8 Headlight 9 Nozzle control knob slide knob to correct setting for height of carpet being cleaned 10 Furniture guard helps prevent cleaner from Operate cleaner only at marking furniture voltage specified on data 11 Wands plate on bottom of cleaner This cleaner is intended for household use 12 Final filter exhaust ON OFF switch Cord clip Plug cord into electrical outlet To help keep the cord out of the way while To turn cleaner ON push switch A toward vacuuming position cord down into cord front of cleaner To turn cleaner OFF push toward back of cleaner clip B located between top cord hook and handle Continued 5 Handle positions The handle of your cleaner has three positions upright for storage and when using cleaning tools operating posi tion for general operation on carpet and floors low for reaching under low furniture Step
3. higher setting Problem Cleaning tools won t pick up Possible cause Possible solution Dirt cup not properly installed Position dirt cup properly and snap in place Fig 3 4 e Blockage in hose e Clear blockage Problem Visible dirt leaking through final filter Possible cause Possible solution Filter assembly not installed properly Ensure that pre filter assembly and main filter are positioned properly Clearing blockages Disconnect cleaner from electrical outlet Low suction or pick up may be due to a blockage in the system Refer to the fol lowing steps to check for blockages continuing with each step until the blockage is found Turn cleaner OFF and disconnect from electrical outlet 1 Check fullness of dirt cup and filter assembly empty cup and clean filters if needed SS GEE Z Z Z Z A Z Z 4 Z 4 Z A A 7 Check dirt duct 2 Remove dirt cup look in duct A 3 Clear blockage from dirt duct Check airflow path 4 Plug cleaner in and turn ON Check for suction at end of hose B a If there is suction continue with step 5 b If there is no suction check for blockage in hose and dirt tube as follows 1 Disconnect hose from dirt duct D by reversing procedure for Attach hose Fig 1 8 and 1 9 2 Clear out hose 3 Look into D and remove block age 5 Check connection at hose tube C remove any blockage Checking under bottom p
4. and use only for ward strokes Edge cleaning Edge cleaning is provided on both sides of the nozzle to remove dirt in carpet near baseboards and furniture Guide either side of nozzle parallel to edge of carpet or furniture Stair cleaning A stair cleaning handle has been designed for ease in using your cleaner on stairs With handle in operating posi tion place fingers under edge of stair cleaning handle and guide cleaner with other hand on upper handle As an alternative you may use the hose and furniture nozzle for stair cleaning Clean from bottom to top When using cleaning tools the agita tor will continue to rotate CAUTION To avoid personal injury or unnecessary wear to carpet and to prevent the cleaner from falling always place it at the bottom of the stairs Cleaning tools Tools allow for cleaning surfaces above the floor and for reaching hard to clean areas The cleaner is ready for tool use when handle is in upright position CAUTION Agitator continues to rotate while cleaner handle is in upright position Avoid tipping clean er or setting it on furniture fringed area rugs or carpeted stairs during tool use How to clean tools To clean the hose wipe off dirt with a cloth dampened in a mild detergent Rinse with a damp cloth Cleaning tools may be washed in warm water with a detergent Rinse and air dry before using Remove hose When using cleaning tools cleaner handle should
5. be in the upright posi tion Also turn cleaner OFF before disconnecting and connecting hose to hose tube A To use hose lift hose end as shown Lower cover B onto hose tube When you are finished cleaning with the tools be sure to lift cover from hose tube and reposition hose end into tube Select proper tool C Dusting brush may be used for carved furniture table tops books lamps lighting fixtures venetian blinds baseboards shutters and registers D Furniture nozzle may be used for upholstered furniture draperies mat tresses clothing automobile interiors and carpeted stairs E Crevice tool may be used in tight spaces corners and along edges in such places as dresser drawers uphol stered furniture stairs and baseboards F Extension wands are used to give extra length to your hose Use it with any of the above tools Attach wand and tools Attach tool or wand to the hose G by pushing it firmly into hose Attach second wand or tool to the wand in the same manner Twist wand or tool slightly to tighten or loosen the connection Extra reach hose available at additional cost The extra reach hose provides you with a 20 foot reach to allow easier cleaning of stairs and hard to reach places Follow the steps below for attaching and detaching hose Push ON OFF switch to OFFp osition Remove regular hose from cleaner Align end of extra reach hose with projec tions
6. H over slots I in dirt duct Slide hose into slots I and twist hose to lock it into place To detach hose reverse procedure Attach wands or tools to the other end of hose Familiarize yourself with these home maintenance tasks as proper use and care of your cleaner will ensure contin ued cleaning effectiveness Dirt cup The dirt cup assembly consists of the following parts Lid A Dirt Cup B Pre filter Assembly C Main Filter D behind pre filter Dirt Opening E While the cleaner is in operation the pre filter assembly screen will stop larger debris from entering the main filter chamber This larger debris will be seen collecting in the left side of the dirt cup The main filter will collect fine particles that have passed through the pre filter assembly screen When to empty It is recommended that the dirt cup be emptied before the dirt reaches the dirt opening on back of dirt cup Fig 3 1 or after every use if preferred CAUTION Very fine materials such as face powder or cornstarch may seal the filter and cause loss of suc tion When using the cleaner for this type of dust empty the cup and clean the filters often How to empty Disconnect cleaner from electrical outlet Do not use the cleaner without dirt cup or filters in place Remove cup Squeeze dirt cup latch Pull cup forward Empty cup Remove lid Note It is not necessary to remove the
7. HOOVERe Bagless Upright Thank you for your purchase a ae eer ct was ee easy assembly see page 3 Review this manual before operating cleaner Thank you for choosing a HOOVER product Please enter the COMPLETE model and serial numbers in the spaces provided The numbers are located on the bottom of your cleaner Model Serial number Hint Attach your sales receipt to this owner s manual Verification of date of purchase may be required for warranty service of your HOOVER product Be sure to fill out and return the product registration card included with your cleaner see back cover FOR HOUSEHOLD USE ONLY 10 SOLAMENTE POUR UN USAGE M NAGER UNIQUE The Hoover Co N Canton Ohio Made in US A Hecho an UA MENT wRTUC 4g7z9 UA 100882 E UA Fabrique aux U Important Safeguards When using an electrical appliance always follow C on t en t S basic precautions including the following Assembling Cleaner 3 4 READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE How to USE wisecccesesssenensnesssesssssssneseeeeeeees 5 r ipti 1 cong E W arnin g To reduce the risk of fire electric shock or injury If te et Seapets E O TE A Do not use outdoors or on wet surfaces iiaportant Safeguard D Close supervision is necessary when any appliance is used by or near children Maintenance Do not allow vacuum cleaner to be used as a toy or to run unattended at any time Authorized Service ceecceccc
8. ccccocecceccecees 142 Keep hair loose clothing fingers feet and all parts of body away from openings Cleaning Filters 9 10 rotating agitator and other moving parts Do not operate cleaner in bare feet or Emptying Dirt Cup sssseceeee 8 when wearing Openitoe shoes or sandals Lubrication scssscsesseseeseseeteseees 12 Do not pick up anything that is burning or smoking such as cigarettes matches or Replacing Agitator Brush Roll 12 hot ashes Replacing Belt 11 Do not use to pick up flammable or combustible materials such as gasoline or fine Replacing Headlight 2 2 10 11 wood sandings or use in areas where they may be present Thermal Protector sssssasssssnnnnennnnnnnnnns 12 Avoid picking up hard sharp objects with the cleaner They may damage the Warranty 14 cleaner Always turn off this appliance before connecting or disconnecting hose Do not use without dirt cup or filters in place Empty dirt cup and clean filters fre quently when picking up very fine materials such as powder Use extra care when cleaning on stairs Do not put any object into openings Do not use with any opening blocked keep free of dust lint hair or anything that may reduce air flow Do not pull or carry by cord use cord as a handle close door on cord or pull cord around sharp edges or corners Do not run appliance over cord Keep cord away from heated surfac
9. er Depot by e checking the Yellow Pages under Vacuum Cleaners Household OR e checking the list of Factory Service Centers provided with this cleaner OR e calling 1 800 944 9200 for an automated referral of authorized service outlet locations U S only OR e checking the Service section of The Hoover Company on line at www hoover com Do not send your cleaner to The Hoover Company in North Canton for service this will only result in delay If further assistance is needed contact The Hoover Company Consumer Response Center North Canton Ohio 44720 Phone 330 499 9499 In Canada contact Hoover Canada Burlington Ontario L7R 4A8 Phone 1 800 263 6376 Always identify your cleaner by the complete model number when requesting information or ordering parts The model number appears on the bottom of the cleaner Hoover cleaning performance This Hoover Cleaning Performance Sys tem is for comparing the relative pro gressive performance of Hoover uprights only and not for comparison with any other brands The majority of this rating is based upon the American Society for Testing and Materials ASTM Carpet Cleaning Effectiveness Test ASTM Test F608 Other performance factors include Hose Power ASTM Test F558 Surface Litter Cleaning Hard Floor Cleaning Edge Cleaning Cleaning Width and Air Filtration If a minor problem occurs it usually can be solved quite easily when the cause is
10. es Always disconnect cord from electrical outlet before servicing the cleaner Unplug cleaner when not in use Turn off all controls before unplugging UL S i Do not unplug by pulling on cord To unplug grasp the plug not the cord Never handle plug or appliance with wet hands The use of an extension cord is not recommended Do not use with damaged cord or plug If appliance is not working as it should has been dropped damaged left outdoors or dropped into water take it to a Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer Depot 2002 The Hoover Company Use vacuum cleaner only for its intended use as described in the instructions Use only attachments recommended by The Hoover Company others may cause www hoover com hazards Save these instructions If you need any assistance Visit our website at www hoover com Click on the Service button to find the service outlet nearest you OR Call 1 800 944 9200 for an automated referral of service outlet locations U S only OR Call 1 330 499 9499 to speak with a representative in our Consumer Response Center Please do not return this product to the store 1 Cleaner Assembly Carton contents Empty carton Find the parts shown before disposing of packing materials A Handle section B Cleaner body C Hose cleaning tools and wands D Handle bolts and nuts packet in bag with owner s manual
11. found by using the check list below Problem Cleaner won t run Possible cause Possible solution e Not firmly plugged in Plug unit in firmly No voltage in wall plug e Check fuse or breaker Blown fuse or tripped breaker e Replace fuse or reset breaker Thermal protector activated Allow cleaner to cool for 30 minutes this will reset the thermal protector see pg 12 Problem Cleaner won t pick up Possible cause Possible solution Broken or worn belt Replace belt e Agitator brush roll worn Replace brush roll e Dirt cup full Empty cup Incorrect carpet height setting Move nozzle control knob to lower setting Blockage in air flow passage e Clear blockage Main filter clogged Clean main filter by either tapping the side of the dirt cup or removing the filter as described in the Filter assembly section Pre filter clogged e Clean pre filter as described in Filter assembly section Dirt cup not properly installed Position dirt cup properly and snap in place Fig 3 4 Dirt cup lid not positioned properly or missing Ensure that dirt cup lid is properly positioned Filter assembly not installed properly Ensure that pre filter assembly and main filter are positioned properly Figs 3 9 to 3 10 Problem Cleaner hard to push Possible cause Possible solution Incorrect carpet height setting Move nozzle control knob to a
12. late 6 Turn cleaner OFF and unplug 7 Remove bottom plate belt and agita tor see The belt section Look into opening E for blockages and remove 8 Remove agitator shield see Fig 3 21 and remove any loose debris which may have accumulated under it 13 Full One Year LEUR Domestic Use Your HOOVER appliance is warranted in normal household use in accordance with the Owner s Manual against original defects in material and workmanship for a period of one full year from date of purchase This warranty provides at no cost to you all labor and parts to place this appliance in correct operating condition during the warranted period This warranty applies when the appliance is purchased in the United States including its territories and possessions or in Canada or from a U S Military Exchange Appliances purchased elsewhere are covered by a limited one year warranty which covers the cost of parts only This warranty does not apply if the appliance is used in a commercial or rental application Warranty service can only be obtained by presenting the appliance to one of the following Authorized Warranty Service outlets Proof of purchase will be required before service is rendered 1 Hoover Factory Service Centers 2 Hoover Authorized Warranty Service Dealers Depots For an automated referral of authorized service outlets in the U S A phone 1 800 944 9200 OR visit The Hoover Company on line a
13. main filter or the pre filter assembly to empty the dirt cup Tap side of cup until no more dust parti cles fall from the main filter Replace cup Replace dirt cup lid Place bottom of cup into cleaner Pivot cup and snap into place Filter assembly How to clean filter assembly 3 6 Pull up on pre filter assembly Slide it out Remove main filter from pre filter of cup assembly The pre filter can be cleaned with a soft brush or rinsed with water Remove dirt cup and dirt cup lid as described in How to empty dirt cup Pivot pre filter assembly toward center of cup Bend filter to open pleats Lay filter on top of pre filter Make sure T d f filter until dust particles all filter pleats are inside the edges of paling aaa filter p the pre filter Press on filter gasket F until 4 tabs G 2 on either side of filter Do not tap the soft pleated part of the are set in the slots H on the pre filter filter I Id damage the filter Ster teou g Be careful not to press the filter gasket below the pre filter edge Slide pre filter assembly all the way to Replace dirt cup bottom of cup Pivot pre filter assembly and snap in place Replace dirt cup lid If lid will not close completely the pre filter assembly is not positioned correctly Secondary and final filters Cleaning secondary filter Disconnect cleaner from electrical outlet The secondary filter G loca
14. nd replace shield agitator and bottom plate Figs 3 22 to 3 24 10 Headlight replacement What to buy This cleaner uses a 12 volt wedge base type 912 bulb HOOVER part No 27313101 Remove lens Disconnect clean er from electrical outlet Using a screwdriver remove the two screws as shown and lift off lens Install bulb Pull old bulb straight out of socket Push new bulb straight into socket until locked in place Excessive force is not required Replace lens Reposition lens and secure with the two screws Belt replacement The belt on your Hoover cleaner causes the agitator to rotate and is important for the effective operation of the cleaner The belt is located under the bottom plate of the cleaner and should be checked from time to time to be sure it is in good condition When to replace Disconnect cleaner from electrical outlet To check belt remove bottom plate as shown in How to replace Replace belt if it is stretched cut or broken What to buy To assure effective operation use only genuine HOOVER belts with your cleaner When purchasing a new belt ask for HOOVER part No 38528033 How to replace Disconnect cleaner from electrical outlet Remove bottom plate Place handle in low position and turn cleaner over so bottom side is up Remove the 4 screws as shown with a Phillips screwdriver Lift off bottom plate I Remove agitator brush roll Remo
15. ns in The belt section beginning with Fig 3 18 Discard old agitator Continue following the directions in The belt section to reposition belt new agitator and bottom plate Lubrication The motor is equipped with bearings that contain sufficient lubrication for the life of the motor The addition of lubricant could cause damage Therefore do not add lubricant to motor bearings The agitator brush roll is equipped with two ball bearings that should be lubri cated periodically by a Hoover Factory Service Center or an Authorized Hoover Warranty Service Dealer Depot Thermal protector An internal thermal protector has been designed into your cleaner to protect it from overheating When the thermal protector activates the cleaner will stop running If this happens proceed as follows 1 Turn the cleaner OFF and discon nect it from the electrical outlet 2 Check secondary and final filters for dirt accumulation 3 Refer to Clearing blockages section 4 When cleaner is unplugged and the motor cools for 30 minutes the thermal protector automatically resets and cleaning may continue If the thermal protector continues to activate after following the above steps your cleaner may need servicing see Service section 12 Service To obtain approved HOOVER service and genuine HOOVER parts locate the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Deal
16. on handle release lever to lower handle Transporting cleaner Put handle in upright position Tilt cleaner back on rear wheels Push forward S Carrying handle Use the carrying handle to lift the cleaner Carpet height adjustment The cleaning of carpet and rugs takes place at the nozzle A When it is necessary to raise and lower the nozzle for various carpet pile heights slide the nozzle control knob B to the desired setting Handle position For ease in sliding knob place handle in the upright position C The nozzle will not move into the adjusted position until the cleaner handle is lowered to the operating position D Settings For maximum cleaning performance the following carpet height settings are recommended Lowest setting for all types of carpet Note If the cleaner is difficult to push slide knob to the next higher setting Higher settings for very deep pile carpet where easier pushing effort is desired while maintaining good cleaning perfomance Cleaning lightweight flexible rugs Stand on one end of rug and move cleaner toward other end or edge Before reaching edge push down on handle This will lift up the nozzle front of cleaner as shown and will prevent rug from clinging to cleaner Continue to lift up nozzle so that when you have reached the edge it is completely off the rug Move cleaner back to start again lower nozzle
17. t www hoover com This warranty does not cover pick up delivery or house calls however if you mail your appliance to a Hoover Factory Service Center for warranty service transportation will be paid one way While this warranty gives you specific legal rights you may also have other rights which vary from state to state or province If further assistance is needed or if there are questions concerning this warranty or the availability of warranty service outlets write or phone the Consumer Response Center The Hoover Company 101 East Maple St North Canton Ohio 44720 Phone 330 499 9499 In Canada contact Hoover Canada Burlington Ontario L7R 4A8 Phone 1 800 263 6376 14 gt gt HOOVER y i son marcas registradas HOOVER et ii sont des marques d pos es gt HOOVER and id are registered trademarks 5 02 U8120 900 Printed in Mexico 56511 B49
18. ted under neath the retainer in the bottom of clean er cavity protects the motor from dirt particles If filter becomes dirty remove dirt cup Fig 3 2 Remove screw and pull retainer out Lift out filter Hand wash filter in cold water with mild detergent then air dry Reposition dry filter retainer and screw Replace dirt cup Should you want to replace this filter ask for HOOVER part No 38765019 Cleaning final filter The final filter assists in returning clean air to the room To remove this filter when it becomes dirty remove dirt cup and pull down top of filter Removing and replacing filter Lift out filter H and hand wash it in cold water with mild detergent Let filter air dry and reposition it on the side of cleaner Reposition dirt cup Should you want to replace this filter ask for HOOVER part No 43613026 Do not operate cleaner without any of the filters in place Check agitator shield Because your cleaner picks up so well we strongly recommend you check for debris accumulation under the agitator shield each time you clean the filters Removing debris under the shield will help maintain your cleaner s excellent pick up and suction Remove debris as follows 1 Disconnect cleaner from electrical outlet 2 Check for dirt accumulation by remov ing bottom plate Fig 3 18 removing agitator Fig 3 19 and lifting agitator shield Fig 3 22 3 Remove any debris a
19. ve agitator and used belt Discard used belt 3 20 A Install new belt With lettering on outside of belt and positioned as shown in box on J slide new belt over motor pulley K Replace agitator brush roll Insert agitator through belt and place belt in belt guide L on agitator Should the agitator shield M become dislodged while replacing the belt or the agitator reposition it as shown noting the placement of its belt guide N Secure agitator Grasp agitator firmly and fit it into posi tion by first sliding end opposite the belt into the rectangular slot O on side of cleaner Pull other side of agitator P into place Turn agitator making sure belt is not pinched between agitator and agitator shield Replace bottom plate Reposition bottom plate and 4 Phillips head screws Tighten screws securely Continued 11 The agitator brush roll When to replace When agitator brushes are worn the agitator should be replaced To check condition of brushes discon nect cleaner from electrical outlet Move edge of acard across bottom plate while turning agitator To maintain cleaning effectiveness replace agitator if brushes do not touch card What to buy When purchasing a new agitator ask for HOOVER part No 48414115 How to replace Disconnect cleaner from electrical outlet Remove bottom plate belt and agitator following directio
Download Pdf Manuals
Related Search