Canon EF 400mm f/4 DO IS II USM Super Telephoto Lens for Canon EOS SLR Cameras - ef400f4doisiiusm-im
Contents
1. EF1 4x II III EF2x II III Focal length mm 560 800 Aperture f 5 6 45 f 8 64 Diagonal 4 25 399 Angle of view Vertical 2 25 1 40 Horizontal 3 40 2 35 Maximum magnification x 0 18 0 26 Q Attach the extender to the lens and then attach the lens to the camera To remove it reverse the order Errors may occur if you attach the extender to the camera first With Extender EF2x II III attached to the lens only manual focus is possible However with the EOS 1D X EOS 1Ds Mark III EOS 1Ds Mark Il EOS 1Ds EOS 1D Mark IV EOS 1D Mark III EOS 1D Mark Il N EOS 1D Mark Il EOS 1D EOS 5D Mark III EOS 1V HS EOS 3 camera autofocusing with the center focusing point is possible When shooting with EOS A2 A2E 5 use 0 5 step exposure compensation when using extender EF1 4x II and use 1 step exposure when using extender EF2x Il Extenders cannot be used more than one at a time Fil Autofocusing is still enabled with extender EF1 4x II III attached When an extender is attached the AF speed will become slower to retain proper control AF can be used by updating your camera s firmware Please check the Canon website for information about firmware updates ENG 20 17 Extension Tubes Sold Separately You can attach extension tube EF12 Il or EF25 Il for magnified shots The shooting distance and magnification are shown below Focusing Distance Range mm Magnification2. change the focus When the playback ring is rotated in a certain direction focus changes in the same direction as when the focusing ring is rotated You can make a 2 step change in focus shift speed depending on the angle that the playback ring is rotated to 1 Power focus PF will work while a Live View image is displayed on the camera or when shooting movies for the following cameras EOS 1D X EOS 5D Mark III EOS 6D EOS 70D EOS REBEL T5i 700D SL1 100D T4i 650D T5 1200D EOS M2 2 and EOS M when used together with Mount Adapter EF EOS M 2 Not available in certain countries and regions ENG 11 7 Image Stabilizer You can use the image stabilizer in AF PF or MF mode STABILIZER ONyr OFF iti 1 Set the STABILIZER switch 2 Select the stabilizer mode to ON If you are not going to use the image stabilizer function set the switch to OFF MODE 1 Corrects vibrations in all directions It is mainly effective for shooting still subjects MODE 2 Corrects vertical camera shake during following shots in a horizontal direction and corrects horizontal camera shake during following shots in a vertical direction MODE 3 Corrects vibration only during exposure During panning shots corrects vibration during exposure only in one direction the same as MODE 2 3 First press the shutter button down halfway then press down all the way to take the picture MODE 1 2 Press the
3. shutter button down halfway to stabilize the image in the viewfinder and enable stabilization MODE 3 Press the shutter down halfway to initiate computation of stabilization then press down all the way to enable stabilization ENG 12 8 Tips on Using the Image Stabilizer The image stabilizer for this lens is effective for hand held shots in the following conditions MODE 1 MODE 2 OFF OFF 6 In semi darkened areas such as indoors or When panning subjects in motion outdoors at night 6 In locations where flash photography is prohibited such as art museums and theater MODE 3 stages 6 In situations where your footing is uncertain Since camera shake is stabilized only during 6 In situations where fast shutter settings exposure following a subject is easier such as cannot be used when shooting a fast and irregularly moving player during sports photography ENG 13 Tips on Using the Image Stabilizer 0 The Image Stabilizer cannot compensate for a blurred shot caused bv a subject that moved Set the STABILIZER switch to OFF when vou are taking pictures using the Bulb setting long exposures If the STABILIZER switch is set to ON the image stabilizer function may introduce errors The Image Stabilizer might not be fully effective in the following cases e You shoot from a violently moving vehicle e You move the camera dramatically for a panning shot in Mode 1 The Image Stabilizer consumes
4. x Close distance Long distance Close distance Long distance EF12 Il 2753 13407 0 17 0 03 EF25 Il 2362 6638 0 22 0 07 Gl MF mode is recommended for accurate focusing ENG 21 Specifications Focal Length Aperture 400mm f 4 Lens Construction 12 groups 18 elements Minimum Aperture f 32 Diagonal 6 10 Angle of View Vertical 3 30 Horizontal 5 10 Min Focusing Distance 3 3 m 10 83 ft Max Magnification 0 13x Approx 185 x 278 mm Field of View 7 28 x 10 94 inch at 3 3 m 10 83 ft Filter Any 52 WIl series drop in filter Max Diameter and Length Approx 128 x 232 7 mm 5 04 x 9 16 inch Weight Approx 2100 g 74 1 oz Hood ET 120 WII Lens Cap E 145C Case Lens case 400D The lens length is measured from the mount surface to the front end of the lens Add 26 5 mm when including the lens cap and dust cap The size and weight listed are for the lens only except as indicated The Close up Lenses 250D and 500D cannot be attached Aperture settings are specified on the camera All data listed is measured according to Canon standards Product specifications and appearance are subject to change without notice ENG 22 Canon CT1 8590 000 1406SZ CANON INC 2014
5. more power than normal shooting resulting in fewer shots and a shorter movie shooting time The image stabilizer operates for about two seconds even when your finger is off the shutter button Do not remove the lens while the stabilizer is in operation This will cause a malfunction With Extender EF2x II attached to the lens the Image Stabilizer will work with the following cameras EOS 1D X EOS 1Ds Mark III EOS 1Ds Mark II EOS 1Ds EOS 1D Mark IV EOS 1D Mark III EOS 1D Mark II N EOS 1D Mark Il EOS 1D EOS 5D Mark III 5D Mark II 5D 6D 7D 70D 60D 50D 40D 30D 20D 20Da 10D REBEL T5i 700D SL1 100D T4i 650D T3i 600D REBEL T2i 550D REBEL T1i 500D DIGITAL REBEL XSi 450D REBEL T5 1200D REBEL T3 1100D DIGITAL REBEL XS 1000D DIGITAL REBEL XTi 400D DIGITAL DIGITAL REBEL XT 350D DIGITAL DIGITAL REBEL 300D DIGITAL D60 D30 Elo EOS DCS1 DCS3 D2000 D6000 EOS 1V HS EOS 1N DP HS RS 3 ELAN 7E ELAN 7 30 33 ELAN 7NE ELAN 7N 30V 33V ELAN II ELAN IIE 50 50E REBEL X REBEL XS 500 REBEL G 500N REBEL 2000 300 REBEL Ti 300V REBEL T2 300X REBEL K2 3000V IX IX Lite IX7 3000 88 5000 888 With the EOS 1V HS 3 ELAN 7E ELAN 7 30 33 ELAN 7NE ELAN 7N 30V 33V ELAN II ELAN II E 50 50E REBEL 2000 300 IX IX Lite IX7 and D30 the Image Stabilizer will not work during self timer operation Using a tripod also stabilizes the image However depending on the kind of tripod and shooting conditions some
6. positions in memory to allow instantaneous focusing 10 Can be used with EF1 4x III EF2x Ill extenders 11 Attachment slot provided for wire type security lock located under the cover for the orientation locking knob 12 Tight seal structure provides excellent dustproof and drip proof performance However it is unable to provide complete protection from dust and moisture 13 Designed for lighter weight with parts made of magnesium alloy Based on CIPA Camera amp Imaging Products Association standards ENG 1 Safety Precautions Handling Cautions If the lens is taken from a cold environment into a warm one condensation may develop on the lens surface and internal parts To prevent condensation in this case first put the lens into an airtight plastic bag before taking it from a cold to warm environment Then take out the lens after it has warmed gradually Do the same when taking the lens from a warm environment into a cold one Do not leave the lens in excessive heat such as in a car in direct sunlight High temperatures can cause the lens to malfunction Conventions used in this instruction Q Warning to prevent lens or camera malfunction or damage El Supplementary notes on using the lens and taking pictures Safety Precautions 6 Do not look at the sun or a bright light source through the lens or camera Doing so could result in loss of vision Looking at the sun directly throu
7. Canon EF LENS EF400mm f 4 DO IS Il USM ULTRASONIC B IMAGE STABILIZER Thank you for purchasing a Canon product Canon s EF400mm f 4 DO IS Il USM is a high performance super telephoto lens for use with EOS cameras which includes a newly developed DO lens Gapless Dual Layer Diffractive Optical Element and is designed to be compact and lightweight e DO stands for Diffractive Optics e IS stands for Image Stabilizer e USM stands for Ultrasonic Motor Features 1 An optimal combination of DO elements providing good compensation of chromatic aberration and an aspherical element providing good compensation of aberrations giving superior definition as well as achieving compactness 2 The Image Stabilizer gives the equivalent effect of a shutter speed 4 stops faster when using an EOS 1D X Also a third Image Stabilizer mode effective for shooting irregularly moving subjects 3 SWC Subwavelength Structure Coating reduces flare and ghosting 4 Using a fluorine coating on the foremost and rearmost lens surfaces allows adhered dirt to be removed more easily than before 5 Ultrasonic motor USM for fast quiet autofocus 6 Manual focusing is available after the subject comes into focus in autofocus mode ONE SHOT AF 7 An AF stop button to pause autofocus whenever desired 8 A power focus mode enables smooth focus change 9 A focus preset function for advance storage of focusing
8. ack in the clasp ENG 6 2 Setting the Focus Mode 3 Switching the Focusing 6 To shoot in autofocus AE mode set the focus Distance Range UMD mode switch to AF A To shoot in manual focus MF mode set the You can set the focusing distance range with a focus mode switch to MF and focus by turning switch By setting a suitable focusing distance the focusing ring The focusing ring always range the actual autofocusing time will be works regardless of the focus mode shorter To shoot in power focus PF mode set the Ranges focus mode switch to PF when the focus FULL preset switch p 9 is at OFF For detailed 3 3 m 10 83 ft 9 information see 6 Power Focus PF Mode 3 3 m 10 83 ft 8 m 26 25 ft p 11 8 m 26 25 ft co fil After autofocusing in ONE SHOT AF mode focus manually by pressing the shutter button halfway and turning the focusing ring Full time manual focus ENG 7 4 AF Stop Button During autofocus operation you can press the AF stop button to temporarily pause autofocus If the shutter button is still pressed halfway when the AF stop button is released autofocusing will continue as before Gl The AF stop function also works in Al Servo AF mode Angle positioning of the AF stop button is adjustable by a Canon Service Center at cost 4 With the EOS 630 600 RT A2 A2E 5 or 105 10 set to the Al Servo AF mo
9. button 9 selector switch gt 7 Focus preset switch 9 sine resi ripod mount gt Focus mode switch 7 For detailed information reference page numbers are provided in parentheses ENG 5 1 Mounting and Detaching the Lens See your camera s instructions for details on mounting and detaching the lens Q A I a After detaching the lens place the lens with the rear end up to prevent the lens surface and contacts from getting scratched If the contacts get soiled scratched or have fingerprints on them corrosion or faulty connections can result The camera and lens may not operate properly If the contacts get soiled or have fingerprints on them clean them with a soft cloth If you remove the lens cover it with the dust cap To attach it properly align the lens mount index and the O index of the dust cap as shown in the diagram and turn clockwise To remove it reverse the order 0 The lens mount has a rubber ring for enhanced dust and water resistance The rubber ring may cause slight abrasions around the camera s lens mount but this will not cause any problems If the rubber ring becomes worn it is replaceable by a Canon Service Center at cost Attaching the strap Thread the end of the strap through the strap mount on the lens and then back through the clasp on the strap Pull the strap tight and check that there is no sl
10. de and continuous shooting AF will not resume even after you let go of the AF stop button Press the shutter release button halfway to resume AF 0 With the EOS A2 A2E 5 and 105 10 set to the Sports mode AF will not resume even after you let go of the AF stop button Press the shutter release button halfway to resume AF You can change the functions of the AF stop button using the camera s Custom Function For details please refer to the camera s instructions ENG 8 5 Focus Preset By presetting any focusing distance you can instantly focus at that point even while you are Shooting a different subject This function operates in any of the AF PF and MF modes lt How to Set gt FOCUS PRESET FOCUS PRESET OFF ate xp FN OFF DE q 1 Set the focus preset switch 2 Press the shutter button 3 Press the focus preset to ON or halfway or turn the focusing button ring to focus the distance you want to preset The focused distance will be preset If the focus preset switch was set to the beeper will sound once ENG 9 Focus Preset By turning the playback ring to the left or right the focus shifts as far as the preset distance Focus will shift freely released of AF focusing while the playback ring is still turned 6 If the focus preset switch was set to Ii the beeper will sound twice Setting the focus mode switch to power focus PF when using t
11. f the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help ENG 4 Nomenclature Focusing ring 7 Distance scale 15 8 Hood mount 15 Orientation locking knob 1 Security slot covered gt 18 Strap mount gt 6 Drop in filter gt 19 Playback ring gt 10 Rubber ring gt 6 AF stop button gt 8 Contacts 7 6 Image stabilizer mode selector switch 7 12 L nemountind ls 6 unt I X gt Image stabilizer switch 12 Focusing distance tende USI I Focus preset
12. gh the lens is especially hazardous Do not point the lens or camera at the sun or photograph it This is because the lens concentrates the sun s ravs even when the sun is outside the image area or when shooting with backlight which could cause malfunction or fire Whetheritis attached to the camera or not do not leave the lens under the sun without the lens cap attached This is to prevent the lens from concentrating the sun s rays which could cause a fire When the lens is mounted on a camera be sure to also hold the camera by the lens including when mounting on a tripod Only holding by the camera could result in scratches on the camera body or the lens itself The lens may also detach from its mount and fall causing injury Do not use a strap attached to the camera The mount may break resulting in the lens falling off and causing injury or in scratches on the camera Be sure to use the camera with a dedicated strap attached correctiv to the strap mount on the lens Refer to Attaching the strap Do not stand on top of the lens case You may fall and injure yourself Do not pile lens cases on top of one another as they may fall and cause injury ENG 2 Usage Precautions When using this lens please check the Canon website for the latest camera firmware If the camera s firmware is not the latest version be sure to update to the latest firmware For details on updating firmware plea
13. he lens with the following cameras enables focus change to a preset focusing distance at a slow speed during movie shooting Also you can make a 2 step change in focus shift speed depending on the angle that the playback ring is rotated to EOS 1D X EOS 5D Mark III EOS 6D EOS 70D EOS REBEL T5i 700D SL1 100D T4i 650D T5 1200D EOS M2 and EOS M when used together with Mount Adapter EF EOS M Q When turning the playback ring keep your finger away from the shutter button In One Shot AF mode the exposure will be locked when you press the shutter button halfway and focus is achieved So if you press the shutter button halfway while turning the playback ring the exposure may not be correct When not using the focus preset set the switch to OFF The focus preset function will work while a Live View image is displayed on the camera or when shooting movies for the following cameras EOS 1D X EOS 5D Mark III EOS 6D EOS 70D EOS REBEL T5i 700D SL1 100D T4i 650D T5 1200D EOS M2 and EOS M when used together with Mount Adapter EF EOS M Not available in certain countries and regions ENG 10 6 Power Focus PF Mode Using the playback ring enables smooth focus change This is a useful feature for changing focus when shooting movies 1 on FOCUS PRESET ON OFF 41 r l 1 With the focus preset switch set to OFF set the focus mode 2 Rotate the playback ring to switch to PF
14. se check the Canon website Shooting Precautions As a characteristic of the diffractive optics with this lens colored flare may occasionally appear around the light source depending on shooting conditions For scenes where a light source is inside the screen colored flare may occasionally appear as a halo of light around the light source or appear fanning out from the light source For scenes where a light source is outside the screen colored flare may occasionally appear partially inside the screen You can reduce or prevent these issues with the following steps according to the scene you are shooting e Attach a lens hood e Use your hand or paneling an umbrella etc to block the light source and placed so that they do not appear in the screen ENG 3 Safety Precautions This device complies with Part 15 of the FCC Rules CAN ICES 3 B NMB 3 B Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept anv interference received including interference that mav cause undesired operation Do not make anv changes or modifications to the equipment unless otherwise specified in the instructions If such changes or modifications should be made vou could be required to stop operation of the equipment This equipment has been tested and found to comply with the limits for a class B digital device pursuant to part 15 o
15. through the viewfinder or look at the magnified image on the LCD screen while rotating the focusing ring For cameras with Live View shooting capability ENG 15 11 Fitting the Lens Cap 1 Reverse the lens hood slip 2 Lift the hook and loop 3 With the lock knob at the it over the lens and tighten fastener and fit the cap so opening in the cap close the lock knob to fix it in that the lock knob rides up the fastener to fix the cap in place the slot in the cap place as shown Can also be attached to the front of the hood when using the lens ENG 16 12 Case Slot Strap Lever Put the lens away as follows 1 Reverse the lens hood slip it over the lens and attach the lens cap 2 Position the tripod mount towards you as shown and place it in the case Place so that the hood s lock knob rests in the slot near vou Fold the strap and fit it into the space near the case hinges 3 Fasten the lens securely with the strap Close the lid and then push the lever while holding the lid from above to lock Q Do not sit on top of the lens case Place the lens in the position intended for it ENG 17 13 Using the Tripod Mount A tripod or monopod attaches to the tripod mount on the lens Adjusting the Tripod Mount By loosening the orientation locking knob on the tripod mount you can rotate the camera to set the image for any vertical or horizontal posi
16. times it may be better to turn off the Image Stabilizer function The stabilizer is equally effective for hand held photography and photography with a monopod The Image Stabilizer effect may be reduced however depending on the shooting environment The Image Stabilizer also operates when the lens is used with extension tube EF 12 Il or EF25 Il or the extender EF1 4x Ill or EF2x III Depending on the camera there may be image shake such as after releasing the shutter However this does not affect shooting If you set the camera s Custom Function to change the assigned button to operate the AF the Image Stabilizer will operate when you press the newly assigned AF button ENG 14 9 Infinity Compensation 10 Hood Mark Infinity compensation mark 9 Distance index l The special hood that comes with the lens cuts out unwanted light and protects the front of the To compensate for shifting of the infinity focus lens from rain snow and dust point that results from changes in temperature To attach the hood loosen the hood lock knob The infinity position at normal temperature is the by turning it counterclockwise Fit the hood onto point at which the vertical line of the distance the lens s hood mount and tighten the lock knob scale L mark is aligned with the distance index to fix it in place Use the same procedure in reverse to remove the hood Q For accurate manual focusing of subjects at infinity look
17. tion 14 Security Slot An attachment slot is provided for a wire type security lock The slot is located under the cover for the orientation locking knob A wire type security lock can be purchased separately ENG 18 15 Drop In Filters A 52 WIl series drop in gelatin filter holder with a glass filter is included with the lens The drop in filter holder can be used fitted with a gelatin filter sold separatelv lt nstalling and Removing gt To remove the drop in filter press in the left and right lock buttons and pull the filter holder straight up out of the slot To install the drop in filter push the filter holder Straight down into the slot until it clicks into place The filter holder can be installed facing either forwards or backwards ib Because the lens optics are designed to include a glass filter vou must alwavs install the filter holder even if no gelatin filter is fitted lt Using a Gelatin Filter gt N TL 47mm 1 Lift up the holder s retaining plate 2 Cut the gelatin filter as shown and mount it in the holder 3 Return the retaining plate to its closed position Gl The Drop In Screw Type Filter Holder 52 WII and Drop In Circular Polarizing Filter PL C52 WII are also available sold separately ENG 19 16 Extenders Sold Separately Lens specifications when using extender EF1 4x II III or EF2x II III are as follows
Download Pdf Manuals
Related Search