Hoover U6660-900 WindTunnel Bagless Upright Vacuum
Contents
1. Avoid picking up hard sharp objects with the cle a n e r T h ey may damage the cleaner Always turn off this appliance before connecting or disconnecting hose Do not use without dirt cup or filters in place Empty cup and clean filter frequently when picking up very fine materials such as pow d er e Use extra care when cleaning on stairs Do not put any object into openings Do not use with any opening bl o ck e d keep free of dust li n t h a i r or anything that may reduce air flow Do not pull or carry by cord use cord as a handle close door on cord or pull c ord around sharp edges or corners Do not run appliance over cord Keep cord aw ay from heated surfaces Always disconnect cord from electrical outlet before servicing the cleaner Unplug cleaner when not in use Turn off all controls before unplugging Do not unplug by pulling on cord To unplug grasp the plug not the cord Never handle plug or appliance with wet hands The use of an extension cord is not recommended Do not use with damaged cord or plug lf appliance is not working as it should has been dro pped damaged left outdoors or dropped into water take it to a Ho over Facto ry Service Center or Au th o ri zed Hoover Warranty Service Dealer Depot Use vacuum cleaner only for its intended use as described in the instructions Use only attachments recommended by The Hoover Company o th e rs may cause hazards Sav2. Slide button to ON Problem Brush roll not turning Possible cause Possible solution Brush roll in OFF position Move brush roll control to ON position carpet Flat belt broken or worn Replace belt Problem Visible dirt leaking through final filter Possible cause Possible solution Filter assembly not installed properly e Remove filter assembly from dirt cup and ensure that HEPA cartridge filter is properly attached to pre filter screen and that entire filter assembly is properly repositioned inside dirt cup Fig 3 10 through 3 12 Problem Dirt inside dirt cup stops spinning Note Heavy debris may settle to the bottom of the dirt cup and prevent the dirt from spinning without affecting cleaning performance The cleaner can continue to be used even if the dirt is not spinning inside the dirt cup However if the dirt does stop spinning AND there is a noticeable decrease of performance check the items under Cleaner won t pick up P ro bl e m Powered hand tool brush roll won t turn Possible Cause Possible Solution Too much pressure being applied to tool Continue using tool applying light pressure Blockage in turbine channel Remove blockage Broken or worn belt Replace belt Low cleaner suction Check items under Cleaner suction low Clearing blockages piscennect cleaner from electrical outlet Warning Brush roll can start suddenly Unplug c
3. 13 Replacing Headlight 9 Thermal Protector 13 Trouble Shooting 14 Clearing Blockages 14 15 Warranty 2 cece ee 14 UL Rs 2001 The Hoover Company www hoover com wove U5465 900 senes M 12 120V 60Hz 12 0A BAG TYPE Y BELT 38528 033 Hy SER no 000000000X4 USTED 283G HOOVER CO FOR HOUSEHOLD USE ONLY j0 HOGARE O SOLAMENTE POUR UN USAGE M NAGER UNIQUEMENT NRTUC The Hoover Co N Canton Ohio 44720 LR 100882 Made in U S A Hecho en E U A Fabrique aux U Important Safeguards When using an electrical appliance a Iw ays fo I ow basic precautions i n cluding the foll owing READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE a r n n g i To reduce the risk of fire electric shock or injury Do not use outdoors or on wet surfaces e Close supervision is necessary when any appliance is used by or near children Do not allow vacuum cleaner to be used as a toy or to run unattended at any time Keep hair looseclothing fingers feet and all parts of body aw ay from openings rotating agitator and other moving parts Do not operate cleaner in bare feet or when wearing open toe shoes or sandals Do not pick up anything that is burning or smoking suchas cigarettessmatches or hot ashes Do not use to pick up flammable or combu s ti ble materials such as gasoline or fine wood sandings or use in areas where they may be present
4. OFF Switch Plug cord into electrical outlet To turn cleaner ON push switch A up To turn cleaner OFF push switch down Polarized plug Note To reduce the risk of electric shock this appliance has a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install the proper outlet Do not change the plug in any way Self propel feature This feature allows you to control how quickly the cleaner moves Note The self propel feature oper ates only when the cleaner switch and the self propel button are both ON To move forward push handle for ward and guide cleaner away from you To move backward gently pull handle back and guide the cleaner toward you Guide cleaner carefully at first until you have adjusted to the ease of operation For increased control in tight places e g around and under furniture non carpeted floors slide the self propel button to OFF to deactivate the feature Transporting cleaner To move your cleaner from room to room put handle in upright position tilt cleaner back on rear wheels and push forward Carrying cleaner The cleaner can be lifted by using the carrying handle on the back of the cleaner Embedded Dirt FINDER feature With red and green lights C the Dirt F
5. cause Possible solution Broken or worn belt Replace belt Agitator brush roll worn Replace brush roll Dirt cup full Empty dirt cup Incorrect carpet height setting Move nozzle control knob to lower setting e Blockage in air flow passage e Clear blockage HEPA cartridge filter clogged Clean HEPA cartridge filter by either tapping the side of the dirt cup or removing the cartridge filter as described in the Filter assembly sec tion e Pre filter clogged e Clean pre filter as described in Filter assembly section e Dirt cup not properly installed and latched Position dirt cup properly and lock latch Fig 3 5 e Dirt cup lid not positioned properly or missing Ensure that dirt cup lid is properly positioned e Filter assembly not assembled prop erly Ensure that filter assembly is posi tioned properly Figs 3 10 to 3 12 Problem Cleaner hard to push Possible cause Possible solution Incorrect carpet height setting Move nozzle control knob to a higher settting Problem Cleaning tools won t pick up Possible cause Possible solution 14 Cleaner handle not in upright posi tion Ensure that cleaner handle is locked in upright position Blockage in hose e Clear blockage Problem Cleaner won t self propel Possible cause Possible solution Flat belt broken or worn Replace belt Self propel button in OFF position
6. com Do not send your cleaner to The Hoover Company in North Canton for service this will only result in delay Lubrication The motor is equipped with bearings which contain sufficient lubrication for the life of the motor The addition of lubricant could cause damage Do not add lubricant to motor bearings The agitator is equipped with two ball bearings that should be lubricated periodically by a Hoover Factory Service Center or an Authorized Hoover Warranty Service Dealer Depot If further assistance is needed contact The Hoover Company Consumer Response Center North Canton Ohio 44720 Phone 330 499 9499 In Canada contact Hoover Canada Burlington Ontario L7R 4A8 Phone 1 800 263 6376 Always identify your cleaner by the com plete model number when requesting information or ordering parts The model number appears on the bottom of the cleaner Continued 13 4 If you have a problem If a minor problem occurs it usually can be solved quite easily when the cause is found by using the check list below Problem Cleaner won t run Possible cause Possible solution e Not firmly plugged in e Plug unit in firmly No voltage in wall plug e Check fuse or breaker Blown fuse tripped breaker e Replace fuse reset breaker Thermal protector activated Allow cleaner to cool for 30 minutes this will reset the thermal protector Problem Cleaner won t pick up Possible
7. hard to reach places K Crevice wand can be used in tight spaces corners and along edges in such places as dresser drawers uphol stered furniture stairs and baseboards It can also be used for extra reach with the dusting brush and or extension wand L Wands are used to give extra length to your hose Use them with any of the above tools How to attach tool cover The tool cover is designed with a break away feature which allows it to snap free if it is pushed open too far To reattach align hinges of cover with slots on sides of tool storage area Push cover down to secure in place How to clean tools To clean the hose and the powered hand tool wipe off dirt with a cloth dampened in a mild detergent Rinse with a damp cloth Do not submerge powered hand tool in water Cleaning tools may be washed in warm water with a detergent Rinse and air dry before using 3 Maintenance Familiarize yourself with these home maintenance tasks as proper use and care of your cleaner will ensure contin ued cleaning effectiveness Dirt cup The dirt cup assembly consists of the following parts Lid A Dirt Cup B Pre filter C HEPA Cartridge Filter D Dirt Inlet Opening E While the cleaner is in operation the pre filter screen will stop larger debris from entering the HEPA cartridge filter chamber This larger debris will be seen collecting in the left side of the dirt cup The HEPA ca
8. the motor cools for 30 minutes the thermal protector automatically resets and cleaning may continue If the thermal protector continues to acti vate after following the above steps your cleaner may need servicing see Service section Hoover Cleaning Performance This Hoover Cleaning Performance System is for comparing the relative pro gressive performance of Hoover uprights only and not for comparison with any other brands The majority of this rating is based upon the American Society for Testing and Materials ASTM Carpet Cleaning Effectiveness Testing ASTM Test F608 Other performance factors include Hose Power ASTM Test F558 Surface Litter Cleaning Hard Floor Cleaning Edge Cleaning Air Filtration and Cleaning Width Installing groomers Lift off both old edge groomers and slide new edge groomers into position as shown Reposition bottom plate and secure with 4 Phillips head screws Service To obtain approved HOOVER service and genuine HOOVER parts locate the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer Depot by e checking the Yellow Pages under Vacuum Cleaners Household OR e checking the list of Factory Service Centers provided with this cleaner OR calling 1 800 944 9200 for an automated referral of authorized service outlet locations U S only OR e checking the Service section of The Hoover Company on line at www hoover
9. INDER system alerts the user to areas of carpet that may need more cleaning attention It is able to sense when larger amounts of dirt particles especially embedded dirt are removed To let you know that the Dirt FINDER feature is ready the red light will come on when the cleaner is first turned on After a few seconds the red light will go off and the green light will come on Cleaning may then begin Handle positions The handle of your cleaner has three positions upright for storage and when using cleaning tools operating posi tion for general operation on carpet and floors low for reaching under low furniture Step on handle release lever to lower handle The green light will remain on through out cleaning except when the detector senses that a larger amount of dirt is being picked up then the red light will come on When the red light is on you should take additional cleaning strokes in the area until it changes to green The red light may seldom come on during cleaning This means that your cleaner is picking up primarily fine sur face dust and lint which the system may not detect or that the carpet is general ly clean To increase the feature s sen sitivity to dirt set the switch D to the Hi position At other times the red light may stay on for a considerable amount of time This means that the carpet contains a high level of dirt which is being removed by the cleaner To decr
10. Self Propelled WindTunnel Bagless with Powered Hand Tool by HOOVER This product was designed for easy Assembly See page 3 Owner s Manual ENGLISH pp 1 15 ESPANOL gt pag 17 26 FRAN AIS p 27 36 Review this manual before operating cleaner Fill in and retain The model and serial number are located on the back of the handle as shown For your personal records please enter the COMPLETE model and serial number in the spaces provided and retain this information Your cleaner is model and has serial number It is suggested that you attach your sales receipt to this owner s manual Verification of date of purchase may be required for warranty service of your HOOVER product Be sure to fill out and return the product registration card included with your cleaner Index Assembling Cleaner 3 Carton Contents 3 HowTo Use Cleaner Descriptions 4 Cleaning Tools 6 7 Embedded Dirt FINDER Feature 5 Upright Cleaner 4 6 Self Propel Feature 4 Important Safeguards 2 Maintenance Authorized Service 13 Cleaning Filters 8 9 Emptying Cup 7 9 Lubrication 13 Replacing Belts 10 11 Replacing Power Hand Tool Belt 12 Replacing Brush Roll 10 11 Replacing Power Hand Tool Agitator Brush Roll 11 12 Replacing Edge Groomers
11. al filter assists in the filtration process to return clean air to the room To replace this filter when it becomes dirty open the door on the side of the cleaner Remove filter N and discard Reposition new filter on the side of cleaner Make sure the white side of the filter faces outward Close door Should you want to replace this filter ask for part No 40110006 Do not operate cleaner without the fil ter in place Headlight replacement What to buy This cleaner uses a 12 volt wedge base type 912 bulb Hoover part No 27313101 Removing lens Disconnect cleaner from electrical outlet Using a screwdriver remove the two screws as shown and lift off lens hel Z Zz Z ANN W Reattaching filter door The filter door is designed with a break away feature which allows it to snap free if it is pushed open too far To reattach align hinges O of cover with slots on sides of filter area Press door back into place Installing bulb Pull old bulb straight out of socket Push new bulb straight into socket until locked in place Excessive force is not required Continued 9 Belt replacement The belts are located under the bottom plate of the cleaner and should be checked from time to time to be sure they are in good condition The flat wide belt is described below the other is described under Brush roll replacement When to replace Disconnect cleaner from elec
12. ance is warranted in normal household use in accordance with the Owner s Manual against original defects in material and workmanship for a period of two full years from date of purchase This warranty provides at no cost to you all labor and parts to place this appliance in correct operating con dition during the warranted period This warranty applies when the appliance is purchased in the United States including its territories and possessions or in Canada or from a U S Military Exchange Appliances purchased else where are covered by a limited two year warranty which covers the cost of parts only This warranty does not apply if the appliance is used in a commercial or rental application Warranty service can only be obtained by presenting the appliance to one of the following authorized warranty service outlets Proof of purchase will be required before service is rendered 1 Hoover Factory Service Centers 2 Hoover Authorized Warranty Service Dealers Depots For an automated referral of autho rized service outlets in the U S A phone 1 800 944 9200 OR visit The Hoover Company on line at www hoover com This warranty does not cover pick up delivery or house calls however if you mail your appliance to a Hoover Factory Service Center for warranty service transportation will be paid one way While this warranty gives you specific legal rights you may also have other rights which vary from state to stat
13. e If further assistance is needed or if there are questions concerning this war ranty or the availability of warranty ser vice outlets write or phone the Consumer Response Center The Hoover Company 101 East Maple St North Canton Ohio 44720 Phone 1 330 499 9499 In Canada contact Hoover Canada Burlington Ontario L7R 4A8 1 800 263 6376 15 16
14. e these instructions 1 Assembling cleaner This cleaner was inspected and packaged carefully before being shipped from the factory If you should happen to need assistance during assembly or operation call 1 800 944 9200 for an automated referral of authorized service outlet locations U S only OR 1 330 499 9499 to speak with a representative in our Consumer Response Center OR Visit us online at www hoover com to find the service outlet nearest you click on the Service button Carton contents Remove all parts from carton and identify each item shown Make sure all parts are located before dispos ing of packing A Handle section B Cleaner body C Hose cleaning tools and wands packed on cleaner D Handle screw packet in bag with owner s manual E Powered hand tool packed on cleaner Note The white switch lock above the ON OFF switch aids in the assembly of your cleaner Assembly can be continued if the switch lock is missing However do not remove the switch lock until assembly is completed some models include an extra hose Easy 3 step assembly Looking at the back of the cleaner make sure switch A is in the OFF position It may be necessary to move the hose in order to attach the handle Slide handle into back of cleaner Push 4 screws into holes on back of handle Using a Phillips screw driver tighten screws securely Remove s
15. ease the feature s sensitivity to dirt set the switch D to the Reg Regular posi tion Carpet height adjustment When it is necessary to raise and lower the front of the cleaner for various car pet pile heights slide the carpet height control B to the desired setting For maximum cleaning performance the following carpet height settings are recommended e Low setting for all types of carpet e Higher settings for very deep pile carpet where easier pushing effort is desired while maintaining good clean ing performance Note If the cleaner is difficult to push slide control to the next higher setting FLOOR CARPET HARD Brush roll control Note When handle is in upright posi tion brush roll is automatically OFF Move the brush roll control only when the handle is in the upright position Slide control to Carpet to turn brush roll ON for cleaning carpet or rugs Slide control to Hard to turn brush roll OFF when cleaning bare floors Continued 5 Cleaning lightweight flexible rugs Stand on one end of rug and move clean er toward other end or edge Before reaching edge push down on handle This will lift up the nozzle front of cleaner as shown and will prevent rug from cling ing to cleaner Continue to lift up nozzle so that when you have reached the edge it is completely off the rug Move cleaner back to start again lower nozzle and use only forward st
16. eely Replace and tighten screws Powered hand tool Belt replacement The powered hand tool belt is designed to last a long time and is not normally replaced However if the belt is crack ed gouged or broken it should be replaced The belt can be seen through the top of the nozzle or by removing the bottom plate and belt guard Figs 3 28 and 3 29 4 With flat sides of turbine retainers G pointing down slide retainers into grooves H in tool housing and snap into place 5 Replace brush roll belt guard and bottom plate as described in Figs 3 30 through 3 33 Edge groomer replacement When to replace The edge groomers located on both sides of the nozzle should be replaced when they are worn What to buy When purchasing edge groomers ask for HOOVER part No 39511004 How to replace Disconnect cleaner from electrical outlet Remove bottom plate as described in The belt section Fig 3 18 Thermal protector An internal thermal protector has been designed into your cleaner to protect it from overheating When the thermal protector activates the cleaner will stop running If this happens proceed as follows 1 Turn the cleaner OFF and discon nect it from the electrical outlet 2 Check dirt cup pre filter HEPA car tridge filter and secondary and final fil ters for dirt accumulation 3 Refer to Clearing blockages sec tion 4 When cleaner is unplugged and
17. es are worn the brush roll should be replaced Ask for HOOVER part No 48414088 How to replace 1 Remove tool from hose and turn it so bottom faces up Press the latches on either side of tool and remove bottom plate A Positioning belt on brush roll Before positioning belt onto brush roll check for debris accumulation as described in Fig 4 1 Insert brush roll through belt and posi tion belt in groove F on brush roll 2 Unscrew the two Phillips screws and remove belt guard B 11 3 Remove agitator including end plates C and discard 4 Inspect belt to ensure that it is in good condition If belt is cracked gouged or broken replace it see follow ing section 5 Insert brush roll through belt and posi tion belt over gear teeth D on brush roll 8 To replace bottom plate A insert the four tabs on edge of bottom plate into slots on front of tool Pivot bottom plate down and snap closed Replacing belt When replacing belt ask for HOOVER part No 38528037 1 Remove bottom plate belt guard and brush roll as described in Figs 3 28 through 3 30 2 Grasp turbine E and pull firmly to remove 3 Remove belt from turbine pulley F Replace with new belt 12 6 With curved ends down slide end 7 Replace belt guard B making sure plates C of brush roll into slots E on not to pinch brush bristles in guard Turn tool agitator making sure it rotates fr
18. leaner when it is turned over Low suction or pick up may be due to a blockage in the system Refer to the fol lowing steps to check for blockages continuing with each step until the blockage is found A If a blockage occurs dur ing floor cleaning Turn cleaner OFF and disconnect from electrical outlet 1 Check fullness of dirt cup and filter assembly empty cup and clean filters if needed Checking under bottom plate 2 Turn cleaner OFF and unplug 3 Remove bottom plate belt and agita tor see The belt section Look into opening C for blockages and remove 4 Remove agitator shield and remove any loose debris which may have accu mulated under it B If a blockage occurs during tool use Turn cleaner OFF and disconnect from electrical outlet 1 Look into hose end and remove any blockage Note Electrical parts are enclosed in the cleaner Do not remove any screws If blockage cannot be removed through existing openings take the cleaner toa Hoover Factory Service Center or an Authorized Hoover Warranty Service Dealer Depot C If blockage occurs during powered hand tool use 4 2 D 1 Disconnect powered hand tool from hose Remove bottom plate belt guard and turbine as described in Figs 3 28 3 29 and 3 35 Remove any blockage from turbine channel D Replace belt turbine brush roll belt guard and bottom plate Full Two Year Warranty Domestic Use Your HOOVER appli
19. r tridge filter will collect fine particles that have passed through the pre filter screen Extra hose The extra hose may be used when additional length is required such as for cleaning stairs The extra hose fits onto the cleaner s hose Remove hose end from cleaner Fig 2 13 Insert short end M of extra hose into cleaner hose To remove extra hose squeeze raised area on cleaner s hose connector N Available at additional cost if not included with your cleaner When to empty It is recommended that the dirt cup be emptied before the dirt reaches the dirt inlet opening on back of dirt cup Fig 3 1 or after every use if preferred CAUTION Very fine materials such as face powder cornstarch or fire place soot may seal the filter and cause loss of suction When using the cleaner for this type of dust empty the cup and clean the filters often How to empty Disconnect cleaner from electrical outlet Do not use cleaner without dirt cup or filters in place Slide latch F to the left to unlock Lift cup slightly and pull straight out to remove from cleaner To remove loose dirt from the HEPA filter turn knob G on top of dirt cup lid at least one complete turn Continued e 7 Press down on area indicated H to open dirt cup lid Empty cup Note It is not necessary to remove the HEPA cartridge filter to empty the dirt cup Filter assembly The HEPA cartridge fil
20. rokes Cleaning tools When using cleaning tools cleaner han dle must be in the upright position to activate the automatic brush roll OFF and for convenience in moving the cleaner from one area to another Turn cleaner OFF before disconnect ing and connecting hose to hose tube E To use hose lift hose end as shown Edge cleaning Special edge groomers are provided on both sides of the nozzle to remove dirt in carpet near baseboards and furniture Guide either side of nozzle parallel to the edge of carpet or furniture Attach wand and tools Attach any tool or wand to the hose F by pushing it firmly into hose Attach second wand or tool to wand G by pushing it firmly onto the wand Twist wand or tool slightly to tighten or loosen the connection Stair Cleaning Use the hose and powered hand tool or furniture nozzle for stair cleaning Clean from bottom to top CAUTION To avoid personal injury or unnecessary wear to carpet and to prevent the cleaner from falling always place it at bottom of stairs Select proper tool H Dusting brush may be used for carved furniture table tops books lamps lighting fixtures venetian blinds baseboards shutters and registers I Furniture nozzle may be used for upholstered furniture draperies mat tresses clothing automobile interiors and carpeted stairs J Powered hand tool may be used for upholstered furniture carpeted stairs and
21. ter and pre filter are essentially self shedding Turning the knob on the lid as described in How to empty dirt cup should suffi ciently remove dust and fine particles from the HEPA cartridge filter The filter assembly can also be removed for additional cleaning The HEPA cartridge filter can be cleaned by tapping either of the ends DO NOT tap soft pleated sides of HEPA car tridge filter as this could damage the filter Tap filter until no more dust particles fall from the filter Close dirt cup lid Note If dirt cup lid does not close com pletely turn knob on lid until lid closes Slide cup straight into cleaner cavity Bottom of cup will rest behind grooves at bottom of cleaner cavity I Press latch F to the right to lock in place How to clean filter assembly Remove dirt cup and open dirt cup lid as described in How to empty dirt cup Grasp pre filter frame J and pull up firmly Slide filter assembly out of cup As the pre filter slides up bristles K mounted inside the cup will brush dirt from the pre filter into the cup 9 To re assemble filter assembly place large knob of HEPA cartridge filter in hole on bottom of pre filter Snap top of HEPA cartridge filter into place The dirt cup lid is designed with a breakaway feature which allows it to snap free if it is pushed open too far To reattach align hinges of lid with slots in handle area of dirt c
22. touch card What to buy When purchasing a new agitator ask for HOOVER part No 48414115 Positioning front of belt Place other end of belt over large pulley C while rolling the pulley in direction shown Replacing brush roll Removing brush roll Slide brush roll control Fig 2 9 to Hard OFF position Turn cleaner over and remove bottom plate Fig 3 18 Lift up brush roll and slide V belt D off brush roll Installing brush roll Grasp brush roll and fit it into position by first sliding end opposite the belt into the rectangular slot G on side of cleaner Push other side of brush roll H into place Belt may fit loosely when properly installed Reposition flat belt and bottom plate Figs 3 20 and 3 22 Y n BA Inspecting V belt The V belt is designed to last for a long time and is not normally replaced However if V belt is cracked gouged or broken now is a good time to replace it as follows Slide flat belt off large pulley as shown in Fig 3 19 To remove V belt slide back of belt over pulley C Then firmly pull on belt and snap it out Discard used belt Replace with HOOVER part No 38528034 To install new belt with lettering on out side of belt slide back of belt over pulley and pull front of belt toward groove E next to pulley Belt will pop into place Powered hand tool Agitator brush roll replacement When agitator brush roll brush
23. trical outlet Warning Brush roll can start sudden ly Unplug cleaner when it is turned over To check the flat belt remove bottom plate as shown in Fig 3 18 Replace belt if it is stretched cut or broken What to buy To assure effective operation use only genuine HOOVER belts with your cleaner When purchasing a new belt ask for flat belt Hoover part No 38528035 Replacing flat belt Disconnect cleaner from electrical outlet Warning Brush roll can start sudden ly Unplug cleaner when it is turned over b HE A Removing bottom plate Place handle in low position and turn cleaner over so bottom side is up Remove the 4 screws as shown with a Ap ips screw driver Lift off bottom plate Removing used belt Flat belt B operates the self propel feature and indirectly drives the brush roll Remove used belt B from large pulley C and discard Replacing bottom plate Reposition bottom plate and 4 Phillips head screws Tighten screws securely 10 Positioning back of belt With lettering on outside of belt slide new belt over motor shaft D The agitator brush roll When to replace When agitator brushes are worn the agi tator should be replaced To check condition of brushes discon nect cleaner from electrical outlet Move edge of a card across bottom plate while turning agitator Fig 3 23 To maintain cleaning effectiveness replace agitator if brushes do not
24. up Push lid down to snap in place Grasp end of HEPA cartridge filter and pull it away from pre filter Remove car tridge from assembly The pre filter can be cleaned with a brush and then rinsed with water Allow pre filter to dry thoroughly Align grooves L on pre filter frame with ribs M in dirt cup Slide filter assembly down into cup until a light snap is felt Gently pull up on assembly to ensure that it is seated properly in the cup Ensure that no part of pre filter screen extends above top edge of dirt cup Close lid and return cup to cleaner Fig 3 5 Note If dirt cup lid does not close all the way first ensure that filter assembly is pushed down all the way Then turn knob on lid slightly until lid closes see Fig 3 3 Check brush roll channels Because your cleaner picks up so well we strongly recommend you check for debris accumulation in the channels next to the brush roll when you check the filters Removing this debris will help maintain your cleaner s excellent pick up and suction Remove debris as follows Disconnect cleaner from electrical outlet Check for debris accumulation by removing bottom plate Fig 3 18 and looking in the channels next to the brush roll Fig 3 27 Remove any accumulation Reposition bottom plate Fig 3 22 Replacing lens Reposition lens and secure with the two screws a RI a LY Final filter Replacing final filter The fin
25. witch lock B above ON OFF switch C on front of handle by pulling it straight out Dispose of lock If switch lock has come off during assembly make sure switch is in OFF position down before plug ging cord into electrical outlet Remove label D from self propel button You are now ready to use America s Best Cleaning Upright Continued gt 3 Cleaner description Operate cleaner only at voltage specified on data plate on bottom of cleaner The assembled cleaner will 16 Nozzle control knob look like the drawing slide knob to correct setting for height of car 1 Handle pet being cleaned 2 Self propel button 17 Brush roll control 3 ON OFF switch 18 Furniture guard 4 Tool cover 19 Headlight 5 Powered hand tool 20 Edge groomers 6 Dusting brush 21 Hose 7 Furniture nozzle 22 Hose rack 8 Dirt cup latch 23 Dirt FINDER display 9 Dirt cup lid 24 Embedded Dirt FINDER 10 Dirt cup sensitivity switch 11 Dirt cup handle 25 Cord hooks wrap 12 HEPA cartridge filter inside dirt cup 13 Pre filter inside dirt cup 14 Final filter 15 Three position handle cord around hooks for storage The top hook can be rotated right or left for easy cord release tions release pedal step on 26 Carrying handle pedal to lower handle to 27 Extension wands operating or low posi 28 Crevice wand stores in rear wand This cleaner is intended for household use ON
Download Pdf Manuals
Related Search