U-Line BI-95
Contents
1. 11 Start Up Troubleshooting 11 Service Information 12 IMPORTANT PLEASE READ all instructions completely before attempting to install or operate the unit This unit requires connection to the water supply Improper hook up can result in substantial property damage If you are unsure of your ability to safely connect the water supply to the unit consult a licensed plumber for assistance This unit requires connection to a grounded three prong polarized receptacle that has been placed by a qualified electrician in accordance with applicable electrical codes Safety Alert Definitions Safety items throughout this guide are labeled with a Danger Warning or Caution based on the risk type DANGER Danger means that failure to follow this safety statement will result in severe personal injury or death WARNING Warning means that failure to follow this safety statement could result in serious personal injury or death CAUTION Caution means that failure to follow this safety statement may result in minor or moderate personal injury property or equipment damage 1 Follow Safety Precautions 02 2005 3 www U LineService com BI 95 Ice Maker General Precautions Use this appliance for its intended purpose only and follow these general precautions along with t2. side 4 Install hinge on opposite side bottom of cabinet See Figure 7 Replace nut on back side where installed Align hinge outer edge with cabinet before tightening screws 5 Relocate plastic spacer bushing on bottom of door to opposite side and place door on bottom hinge pin See Figure 8 Clean out bushing hole in door bottom with a screwdriver if necessary 6 Remove plastic hole plug from door handle and relocate on opposite side See Figure 9 7 Remove pivot screw from top hinge invert screw and reinstall pivot screw in top hinge See Figure 9 8 Remove three plastic screw plugs from hinge holes top of cabinet opposite side Be careful not to scratch cabinet See Figure 10 9 Place door on lower hinge pin Invert and install upper hinge on door Figure 4 Figure 5 Figure 6 Figure 7 Bushing Figure 8 Plastic Plug Hole Plastic Plug Hole Hinge Screw Right Side Door Swing Right Side Hinge Invert Screw Invert Hinge Left Side Door Swing Figure 9 Figure 10 www U LineService com 6 02 2005 BI 95 Ice Maker 10 Fasten upper hinge to unit three screws Partially tighten screws See Figure 11 11 Adjust door to assure proper seal Tighten upper and lower hinge screws securely 12 Replace three plastic plugs removed in Step 8 into holes on top of unit Replace screws in holes in bottom of unit on opposite side Other Site Requirements Power Suppl
3. g the insert Insert edges may be sharp 1 Remove top hinge screw pin with a Phillips head screwdriver see Figure 12 Remove door by tilting forward and lifting off bottom hinge pin Figure 11 4 Prepare and Install Door Panel
4. hose listed throughout this guide WARNING SHOCK HAZARD Electrical Grounding Required Keep the unit unplugged throughout installation except during testing Never remove the round grounding prong from the plug and never use a two prong grounding adapter Never use an extension cord to connect power to the unit Always keep your working area dry CAUTION Use care when moving and handling the unit Use gloves to prevent personal injury from sharp edges Do not lift the unit by the door or door handle Do not install the unit behind closed doors or in any way that would obstruct airflow to the front grille which may cause the unit to malfunction You have received a carton containing your BI 95 Ice Maker with a package inside containing a User Manual a Product Registration Card and water connection parts Complete and mail the Product Registration Card or register online at www U LineService com Once your unit is installed keep the User Manual and this Installation Guide in a safe place for future reference BI 95 units are available in vinyl clad cabinets with matching doors which have a slightly contoured handle across the top and are reversible The doors have recessed front panels that will accept a custom 1 4 inch thick door panel Please carefully follow the directions that apply to your unit and your intended design Tools Materials Required Screwdrivers sl
5. otted and Phillips head 1 4 inch OD copper tubing and shut off valve for water supply line 1 4 inch thick door panel material and cutting tools Inspection Unwrap and inspect the unit on a flat level surface capable of supporting its entire weight Exterior Cleaning As Required Black and White Models Black and white surfaces may be cleaned with a mild detergent and warm water solution Do not use solvent based or abrasive cleaners Use a soft sponge and rinse with clean water Wipe with a soft clean towel to prevent water spotting 2 Inspect and Plan www U LineService com 4 02 2005 BI 95 Ice Maker Your U Line product has been designed for either free standing or built in installation When built in your unit does not require additional air space for top sides or rear However the front grille must NOT be obstructed and clearance is required for water and electrical connections in the rear Note Unit can NOT be installed behind a closed cabinet door Cut Out Dimensions Follow the cut out drawing in Figure 1 The 14 3 16 width allows 1 4 for ease in installation and removal of the unit 24 is the counter depth in most installations 18 1 2 depth includes the door handle and water line connection see Figure 2 IMPORTANT It is extremely important that the unit sits on a level surface as it does not have feet levelers If it is not level the ice mold will not fill evenly Produc
6. t Dimensions Door Swing Clearances Information Units have a zero clearance for the door to open 90 see Figure 3 U Line recommends a minimum door clearance of 1 4 to accommodate the handle if the unit is right hand hinged and installed next to a wall or similar type of structure Note When a raised panel is used additional clearance is needed for easy removal of ice bin if door hinge side is installed adjacent to wall 3 Prepare Site 8 Typical Counter Height 34 1 4 to 35 1 8 Cut Out Height 24 7 8 to 25 Filler Panel Not Provided by U Line May Be Added Above or Below Unit to Enclose for a Built In Look 14 3 16 18 1 2 Minimum See Electrical Specifications for Power Supply Figure 1 17 Including Handle 24 3 4 13 15 16 Figure 2 1 4 Min Wall 90 Door Swing 14 3 8 15 1 2 Figure 3 02 2005 5 www U LineService com BI 95 Ice Maker Reversing the Door All units may be left or right hand opening Note The grille should not yet be installed If it has been installed remove it for door reversing See Page 10 To reverse the door 1 Remove top hinge from cabinet three screws See Figure 4 Hold door to keep it from falling 2 Lift the door off the bottom hinge 3 Remove bottom hinge from cabinet two screws See Figure 5 Remove screws on opposite side of cabinet Figure 6 Note that there may be a nut behind one or both screws on either
7. www U LineService com Phone 414 354 0300 FAX 414 354 7905 Service amp Parts Tech Lines Phone 800 779 2547 FAX 414 354 5696 OnlineService U Line com 2005 U Line Corporation 02 2005 BI 95 Ice Maker Installation Guide www U LineService com 2 02 2005 BI 95 Ice Maker Contents Exterior Cleaning 3 Cut Out Dimensions 4 Product Dimensions 4 Door Swing Clearances Information 4 Reversing the Door 5 Other Site Requirements 6 Custom 1 4 Thick Door Panel Insert 6 Checking Door Alignment 7 Adjusting Door Alignment 7 Water Supply Connection 8 Electrical Specifications 9 Leveling Information 9 Installation of the BI 95 10 Grille Installation 10 Installation Troubleshooting 10 Initial Start Up
8. y The unit requires a grounded and polarized 115 VAC 60 Hz 15A circuit normal household current See Electrical Specifications on Page 9 Water Supply The unit requires a 1 4 inch OD water supply line and a shut off valve For more information see Page 8 Environmental Requirements The surrounding air temperature must be at least 50 F 10 C but must not exceed 110 F 40 C Units may be installed outdoors in a covered area The unit must not be located near heat generating equipment or in direct sunlight Units will accept a Custom 1 4 Thick Insert to harmonize with or accent the surrounding decor If this treatment is not included in this installation go on to 5 Adjust Door Custom 1 4 Thick Door Panel Insert Door Panel Preparation A custom door panel can be inserted into the doorframe Custom door panels can be flat or raised as long as the maximum panel thickness where inserted into the door reveal channel is 1 4 thick For raised panels the depth of the reveal is 1 4 on all four sides IMPORTANT Raised panels will reduce the door s 90 swing zero clearance if the unit is installed next to a wall or similar type of structure see Page 4 Cut the panel insert to the following dimensions Custom 1 4 Dimensions Width 12 15 16 Height 13 15 32 The door panel must not weigh more than 20 lbs Door Panel Installation Install the insert as follows CAUTION Use care when handlin
Download Pdf Manuals
Related Search