Frigidaire PLKU1267DS Stainless Steel Beverage Dispenser
Contents
1. SOCKET WRENCH ADJUSTABLE WRENCH PLIERS DRIP TRAY AND MOUNTING HARDWARE BOX 1 Drip Tray 1 piece 2 Drip Tray Cover 1 piece 3 Drip Tray Bracket 1 piece 4 CO2 Canister Bracket 1 piece 5 Mounting Screws 6 pieces 6 4 Long Carriage Bolt 1 piece 7 Wing Nut 1 piece 8 Hose Routing Clips 2 pieces 1 DRIP TRAY 2 DRIP TRAY 3 DRIP TRAY 4 CO CANISTER COVER BRACKET BRACKET 8 HOSE ROUTING CLIP BEVERAGE DELIVERY KIT BOX 9 Faucet and Shank Assembly 1 piece 10 Plastic Collar 1 piece 11 Shank Nut 1 piece 12 Faucet Knob 1 piece 13 Regulator 1 piece 14 Keg Coupler 1 piece 15 Clear Hose Delivery Line 1 piece 16 Red Hose Gas Line 1 piece 17 Rubber Washer Black 2 pieces 18 Plastic Hose Clamp White 2 pieces 19 CO2 Canister Empty 1 piece 16 RED HOSE 15 CLEAR HOSE DELIVERY LINE GAS LINE 19 CO CANISTER 18 HOSE CLAMP LEVELING The beverage cooler must have all bottom corners resting firmly on a solid floor The floor must be strong enough to support a fully loaded beverage cooler NOTE It is Very Important for your beverage cooler to be level in order to function properly If the beverage cooler is not leveled during installation the door may be misaligned and not close or seal properly causing cooling frost or moisture problems To Level Your Beverage Cooler Carefully tip the unit2. READ AND SAVE THESE INSTRUCTIONS P N 297017400 Oct 2004 SERIAL MODEL NUMBERS READ AND SAVE THESE INSTRUCTIONS This Use and Care Manual provides specific operating instructions for your model Use your beverage cooler only as instructed in this manual These instructions are not meant to cover every possible condition and situation that may occur Common sense and caution must be practiced when installing operating and maintaining any appliance Record Your Model and Serial Numbers Record the model and serial numbers in the space provided below The model and serial number plate is located on the upper left wall inside the beverage cooler Model Number Serial Number Purchase Date Vode and Serial Hurter Plate Version en espanol Si desea obtener una copia en espanol de este Manual del Usuario sivase escribir a la direcci n que se incluye a continuaci n Solicite la P N 297025100 Spanish Owner s Guide Electrolux Home Products P O Box 212378 Augusta GA 30917 IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING THIS BEVERAGE COOLER FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors and liquids in the vicinity ofthis or any other appliance Read product labels for flammability and other warnings CHILD SAFETY e Destroy or safely discard carton plastic bags and any exterior wrapping material immediately after the beverage cooler is unpacked C
3. OPERATING YOUR BEVERAGE COOLER e Make sure that the beverage cooler is plugged in properly to a 115V 60Hz AC only electrical outlet Refer to Electrical Information on page 2 Make sure that the drip tray is secured under the faucet Start with a clean beverage glass that has been wetted in cold water Place the glass at a 45 angle one inch below the faucet Do not let the glass touch the faucet Open the faucet all the way After the glass has reached half full gradually bring the With the canister valve still in closed position reattach the regulator to the new canister using an adjustable wrench Tighten nut until it feels snug but be careful not to over tighten as you will damage the gasket inside the stem nut Check to make sure that the red gas line hose is still securely attached to the regulator Open the canister valve all the way by turning counter clockwise until it stops This valve seals at both the fully open and fully closed positions Failure to completely open or close the valve could result in premature loss of CO2 pressure Open the regulator shut off valve by moving it down to the glass to an upright position JU 6 o clock position e Let the remaining beverage run straight down the middle l This insures proper release of CO2 by producing a 3 to Check gauge pressure Adjust the regulator shut off valve a 1 foam head as necessary until the pressure reads between 12 to 14 e Close the faucet complet
4. RED HOSE TO REGULATOR CONNECTION e Attach one end of the red hose 16 to the hose barb of the CO regulator 13 Secure the hose using one of the two hose clamps 18 provided Use pliers to snap the hose clamp tight to assure that there is no gas leak 13 REGULATOR 18 HOSE CLAMP 16 RED HOSE RED HOSE TO COUPLER CONNECTION e Fasten the other end of the red hose 16 to the keg coupler 14 using the remaining hose clamp 18 Use pliers to snap the clamp tight to assure that there is no gas leak 14 KEG COUPLER 18 HOSE CLAMP 16 RED HOSE CLEAR HOSE TO COUPLER CONNECTION e Attach the end of the clear hose 15 beverage delivery line with the large wing nut to keg coupler 14 Be sure to place the supplied rubber washer 17 inside the nut to prevent leakage 14 KEG COUPLER 15 CLEAR HOSE CLEAR HOSE TO DOOR PANEL CONNECTION DELIVERY HOSE ARRANGEMENT e Place the supplied rubber washer 17 inside the hex nut Insert the clear hose 15 delivery hose into the hose on the other end of the clear hose 15 beverage delivery routing clips 8 attached to the door panel Once the line and attach to shank protruding from the door panel hoses are properly secured the CO2 canister valve can now be opened 15 CLEAR HOSE 8 HOSE 15 CLEAR HOSE ROUTING CLIPS DOOR PANEL DOOR PANEL COUPLER TO KEG INSTALLATION e Align lug locks on tap head with l
5. Rinse all the parts with cool fresh water and reassemble the faucet Detach the cleaning solution bottle from the faucet shank by turning the threaded stainless steel collar clockwise Rinse the bottle with cool fresh water Fill the bottle with fresh water and re attach it to the faucet shank assembly Pump the water through the beverage line clear hose Make sure the end of the line is in a bucket to collect rinse water Disconnect the cleaner and reinstall the faucet to the shank by turning the collar counterclockwise using a faucet wrench and tightening it slightly DO NOT over tighten the collar Reattach the red hose air line to the keg coupler and open both the canister valve and regulator shut off valve Reattach the keg coupler to the keg Refer to Coupler Keg Installation procedures Remove the drip tray and cover from the door and clean thoroughly Refer to Cleaning and Maintenance Guide Reinstall the drip tray and cover to the door Refer to Drip Tray Assembly Installation procedures keg by rotating it NOTE Read and follow the instructions that come with the cleaning kit before cleaning your beverage cooler VACATION AND MOVING TIPS e f the unit will not be used for several months unplug the power cord clean and dry the interior thoroughly and leave the door open slightly blocking it open if necessary to prevent odor and mold growth e When moving the unit disconnect the power cord from the wall outl
6. Profile Hand Pump C Solid Brass Faucet Cleaning Attachment D 4 oz Bottle of Cleaning Solution E Faucet Wrench F Faucet Cleaning Brush e Mix one gallon of warm water with one ounce of the cleaning solution in a bucket e Remove the bottle cap and fill the bottle with the solution Replace the cap Do not discard the remaining solution e Before removing the beverage hose from the tap or from the coupler make sure the remaining beverage in the delivery line is blown out This can be done by quickly opening and closing the regulator outlet valve e Remove the coupler from counterclockwise Remove the red hose gas line from the coupler Make sure the canister valve and regulator shut off valve is shut off before removing the hose Remove the faucet from the shank assembly by turning the threaded stainless steel collar clockwise using a faucet wrench Disassemble the faucet parts and place in the cleaning solution bucket Attach the brass attachment on the end of the cleaning hose to the faucet shank assembly by turning the stainless steel collar counterclockwise Tighten the collar slightly If the coupler has a shutoff make sure it is in the open position Place the keg coupler in the cleaning solution bucket and pump the cleaning solution through the beer line Clean the faucet parts and keg coupler thoroughly using the faucet cleaning brush Also use the faucet cleaning brush to clean around the shank and coupling
7. as described or illustrated are subject to change without notice All warranties are made by Electrolux Home Products Inc In Canada your appliance is warranted by Electrolux Canada Corp 01 U FR 02 Rev 02 2004 USA Canada 800 944 9044 800 265 8352 Electrolux Home Products Inc Electrolux Canada Corp P O Box 212378 6150 McLaughlin Road Augusta GA 30917 Mississauga Ontario L5R 4C2 10 TROUBLESHOOTING GUIDE PROBLEM Before calling for service review this list It may save you time and expense This list includes common occurrences that are not the result of defective workmanship or materials in this appliance CAUSE CORRECTION BEVERAGE COOLER OPERATION Beverage cooler does not run e Beverage cooler is plugged into a circuit that has a ground fault interrupt e Temperature control is in the OFF position e Beverage cooler may not be plugged in or plug may be loose e House fuse blown or tripped circuit breaker e Power outage eUse another circuit If you are unsure about the outlet have it checked by a certified technician eSee SETTING THE TEMPERATURE CONTROL Section e Ensure plug is tightly pushed into outlet e Check replace fuse with a 15 amp time delay fuse Reset circuit breaker e Check house lights Call local Electric Company Beverage cooler runs too much or too long e Room or outside weather is hot e Beverage cooler has recently been disconnected
8. onto its back Remove and discard the wood skid from the bottom using a 3 8 socket wrench After discarding crating screws and wood skid use a carpenter s level to level the beverage cooler from front to back Adjust the plastic leveling feet in front 2 bubble higher so that the door closes easily when left halfway open Plastic Leveling Feet Crating Screw pe Unpacking and Leveling INSTALLATION GENERAL INSTRUCTIONS Choose a place that is near a grounded electrical outlet DO NOT use an extension cord or an adapter plug e For the most efficient operation the beverage cooler should be located where surrounding temperatures will not drop below 10 F 12 C or exceed 110 F 43 C Allow space around the unit for good air circulation Leave a 3 inch 75 mm space on all sides of the beverage cooler for adequate air circulation 3 AIR SPACE Installation NOTE The exterior walls of the beverage cooler may become quite warm as the compressor works to transfer heat from the inside Temperatures as much as 30 F warmer than the room temperature can be expected For this reason it is particularly important in hotter climates to allow enough space for air circulation around your beverage cooler CO CANISTER BRACKET INSTALLATION e Align the two bracket holes with the screw anchor holes located on the lower left side of the cabinet the actual screw anchor holes are centered behind the tap
9. own 115 Volt 60 Hz AC only electrical outlet The power cord of the appliance is equipped with a three prong grounding plug for your protection against shock hazards It must be plugged directly into a properly grounded three prong receptacle The receptacle must be installed in accordance with local codes and ordinances Consult a qualified technician DO NOT use an extension cord or adapter plug If voltage varies by 10 or more performance of your beverage cooler may be affected Operating beverage cooler with insufficient power can damage the compressor To prevent the beverage cooler from being turned off accidentally do not plug unit into an outlet controlled by a wall switch or pull cord It is recommended that a separate circuit serving only your beverage cooler be provided Do not pinch knot or bend the cord in any manner rA OTHER PRECAUTIONS DO NOT use this appliance outside It is designed for indoor use only NEVER unplug the beverage cooler by pulling on the cord Always grip the plug firmly and pull straight out from the receptacle To avoid electrical shock unplug the beverage cooler before cleaning NOTE Turning the temperature control to OFF turns off the compressor but does not disconnect the power to other electrical components A WARNING Avoid fire hazard or electric shock Do not use an extension cord or an adapter plug Do not remove any prong from the power cord Grounding type wa
10. NCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY NOTE Some states do not allow the exclusion or limitation of incidental or consequential damages so this limitation or exclusion may not apply to you 2 Service calls which do not involve malfunction or defects in workmanship or material or for appliances not in ordinary household use The consumer shall pay for such service calls 3 Damages caused by services performed by servicers other than Electrolux Home Products Inc or its authorized servicers use of parts other than genuine Electrolux Home Products Inc parts obtained from persons other than such servicers or external causes such as abuse misuse inadequate power supply or acts of God 4 Products with original serial numbers that have been removed or altered and cannot be readily determined IF YOU NEED Keep your bill of sale delivery slip or some other appropriate payment record The date on the bill establishes the SERVICE warranty period should service be required If service is performed it is in your best interest to obtain and keep all receipts This written warranty gives you specific legal rights You may also have other rights that vary from state to state Service under this warranty must be obtained by contacting Electrolux Home Products Inc or Electrolux Canada Corp This warranty only applies in the 50 states of the U S A Puerto Rico and Canada Product features or specifications
11. NING THE OUTSIDE Wash the cabinet with warm water and mild liquid detergent Rinse well and wipe dry with a clean soft cloth Replace parts Adjustable Interior Shelves DOOR REMOVAL If door must be removed e Gently lay the beverage cooler on its back on a rug or blanket Remove plastic top hinge cover Remove screws from top hinge Remove top hinge from cabinet Remove bottom hinge screws Remove door and bottom hinge from cabinet To replace door reverse the above order and securely tighten all screws to prevent hinge slippage Top Hinge Cover Top Hinge Screws PAGUINA If leaving the beverage cooler door open at any time make certain that children cannot get into the beverage cooler and become entrapped PROPER CLEANING OF BEVERAGE COOLER Your beverage cooler s beverage dispensing system needs regular cleaning and sterilization in order to continue serving draft beer with its pure brewery flavor It is recommended that the delivery lines be cleaned weekly and the entire delivery system cleaned before a new keg is attached This is a relatively simple task You will need the following parts to clean your unit s dispensing system These parts are available at any draft beer dispensing equipment supplier One such supplier is Micro Matic They can be reached at www micromatic com or call them toll free at 866 291 5756 A 1 quart Plastic Cleaning Bottle B Low
12. because of Applicable to the date service State of Alaska In the U S A your appliance is warranted by Electrolux Home Products Inc We authorize no person to change or add to any of our obligations under this warranty Our obligations for service and parts under this warranty must be performed by us or any authorized Electrolux Home Products Inc servicer In Canada your appliance is warranted by Electrolux Canada Corp NORMAL This warranty applies only to products in ordinary household use and the consumer is responsible for the items RESPONSIBILITIES listed below OF THE CONSUMER 1 Proper use of the appliance in accordance with instructions provided with the product 2 Proper installation by an authorized servicer or in accordance with instructions provided with the appliance and in accordance with local plumbing electrical and or gas codes 3 Proper connection to a grounded power supply of sufficient voltage replacement of blown fuses repair of loose connections or defects in house wiring 4 Expenses for making the appliance accessible for servicing such as removal of trim cupboards shelves etc which are not a part of the appliance when it was shipped from the factory 5 Damages to finish after installation 6 Replacement of light bulbs and or fluorescent tubes on models with these features EXCLUSIONS This warranty does not cover the following 1 CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND I
13. completely Beverage cooler external surface temperature is warm e The external walls can be as much as 302F warmer than room temperature SOUND AND NOISE e This is normal while the compressor works to transfer heat from inside the beverage cooler Louder sound levels whenever beverage cooler is on eModern beverage coolers have increased storage capacity and more stable temperatures They require a high efficiency compressor e This is normal When the surrounding noise level is low you might hear the compressor running while it cools the interior Longer sound levels when compressor comes on e Beverage cooler operates at higher pressures during the start of the ON cycle e This is normal Sound will level off or disappear as the beverage cooler continues to run Fan runs when room temperature is below 45 F e Exterior thermostat has activated the heater and fan e This is normal Popping or cracking sound when compressor comes on e Metal parts undergo expansion and contraction as in hot water pipes e This is normal Sound will level off or disappear as refrigerator continues to run Bubbling or gurgling sound like water boiling e Refrigerant used to cool beverage cooler is circulating throughout the system e This is normal 11 SOUND AND NOISE Cont Vibrating or rattling noise Snapping sound e Beverage cool
14. ed hole e Secure the CO2 canister bracket 4 to the cabinet with the two supplied mounting screws 5 using a Phillips screwdriver 4 CO2 CANISTER BRACKET 5 MOUNTING SCREWS rm DRIP TRAY ASSEMBLY INSTALLATION e Make sure the notched back corners are on top and attach the Drip Tray Bracket 3 to the door using four supplied mounting screws 5 e Drop the Drip Tray 1 onto the bracket e Drop the Drip Tray Cover 2 onto the drip tray 2 DRIP TRAY COVER 3 DRIP TRAY 1 DRIP BRACKET TRAY 5 MOUNTING SCREW FAUCET ASSEMBLY INSTALLATION e Attach Faucet Knob 12 to Faucet amp Shank Assembly 9 e Slip the Faucet amp Shank Assembly through the black plastic Collar 10 and hole in the door e Thread on the large Shank Nut 11 and using an adjustable wrench tighten until snug DO NOT OVER TIGHTEN 12 FAUCET KNOB 9 FAUCET amp SHANK ASSEMBLY 11 SHANK NUT 10 PLASTIC COLLAR CLIP ATTACHMENT TO DOOR PANEL e Attach the two supplied hose routing clips 8 to the door panel approximately 1 2 in 25 50mm from the left door edge See delivery hose arrangement on page 6 8 HOSE ROUTING CLIP DOOR PANEL REGULATOR INSTALLATION e Fasten the CO2 regulator 13 to the COz2 canister 19 tightening the nut securely DO NOT over tighten Over tightening may damage the gasket in nut of the regulator NUT 23 REGULATOR 29 CO2 CANISTER
15. ely and quickly psi NOTE It is normal to see condensation forming around the CANISTER VALVE faucet This condensation is caused by the temperature difference between the cold beverage and the inner surfaces of the faucet when beverage is being drawn through the line HELPFUL HINTS PARTS OF A CO REGULATOR NUT REGULATOR CO CANISTER SHUT OFF VALVE A Low Pressure Gauge B Regulator Adjustment Screw C Adjustment Lock Nut D Shut off Valve E CO2 Nut used to connect to CO2 Canister F High Pressure Gauge TIPS ON INSTALLING THE KEG TO THE CABINET SAFE KEG HANDLING e Installing the keg to the cabinet is a two person team effort NEVER lift a full 2 keg alone Doing so may cause severe Injury With the door fully open and the help of another person lift the keg vertically on both sides until the keg is above the bottom of the cabinet interior Set the edge of the keg on top of the stainless protective plate located on the bottom of the cabinet interior Slide the keg back until it is fully inside the cabinet Care must be taken to avoid damage to the evaporator coils located on the back side of the cabinet interior HOW TO REPLACE AN EMPTY CO CANISTER e Close the canister valve of the empty canister by turning clockwise until it stops e Close the regulator shut off valve by moving it in the 3 o clock position Carefully remove regulator from the empty CO2 canister by loosening
16. er is touching the wall e Move beverage cooler slightly away from the wall e Cold control turning beverage cooler on and off e This is normal WATER MOISTURE FROST INSIDE BEVERAGE COOLER Moisture forms on inside of beverage cooler walls e Weather is hot and humid e Door may not be seating properly e Door is kept open too long or opened too frequently e This is normal eSee DOOR PROBLEMS Section e Open the door less often WATER MOISTURE FROST OUTSIDE BEVERAGE COOLER Moisture forms on outside of beverage cooler walls e Door may not be seating properly causing the cold air from inside the beverage cooler to meet warm moist air from outside ODOR IN BEVERAGE COOLER eSee DOOR PROBLEMS Section Odors in beverage cooler e Interior needs to be cleaned e Clean interior with sponge warm water and baking soda DOOR PROBLEMS Door will not close e Beverage cooler is not level It rocks on the floor when it is moved slightly e This condition can force the cabinet out of square and misalign the door Level the unit COMMON DRAFT PROBLEMS WILD BEER Beer when drawn is all foam or too much foam and not enough liquid beer e Beer drawn improperly e Creeping regulator e Applied pressure is set too high e Hot spots in line e Tapped into a warm keg should be 34 F 38 F e Co
17. et Thoroughly clean the interior and secure all loose items by taping them securely in place to prevent damage In the moving vehicle secure the unit in an upright position to prevent movement Also protect the outside of the unit with a blanket or similar item BEVERAGE COOLER WARRANTY Your beverage cooler is protected by this warranty WARRANTY THROUGH OUR AUTHORIZED SERVICERS THIS CONSUMER WILL BE RESPONSIBLE FOR PERIOD WE WILL FULL ONE YEAR One year from Pay all costs for repairing or replacing any parts of Costs of service calls that are listed under NORMAL WARRANTY original purchase this appliance which prove to be defective in RESPONSIBILITIES OF THE CONSUMER date materials or workmanship LIMITED 2 5 Second through Repair or replace any parts in the cabinet liner or Costs for pick up and delivery of the appliance required YEAR WARRANTY fifth years from Sealed Refrigeration System compressor because of service Costs for labor parts and transportation Cabinet Liner and original purchase condenser evaporator drier and tubing which other than with respect to the cabinet liner or Sealed Sealed System date prove to be defective in materials or workmanship Refrigeration System LIMITED Five years from All of the provisions of the warranties above and the Costs of the technician s travel to the home and any costs for WARRANTY original purchase exclusions listed below apply pick up and delivery of the appliance required
18. for a period of time e Doors are opened too frequently or too long e Beverage cooler door may be slightly open e Temperature control is set too low e Beverage cooler gasket is dirty worn cracked or poorly fitted Interior beverage cooler temperature is too cold e Temperature control is set too low e ts normal for the beverage cooler to work harder under these conditions elt takes 4 hours for the beverage cooler to cool down completely e Warm air entering the beverage cooler causes it to run more Open door less often eSee DOOR PROBLEMS Section e Turn the control shaft to a warmer setting Allow several hours for temperature to stabilize e Clean or change gasket Leaks in the door seal will cause beverage cooler to run longer in order to maintain desired temperature e Turn the control shaft to a warmer setting Allow several hours for temperature to stabilize Interior beverage cooler temperature is too warm e Temperature control is set too warm eDoor is kept open too long or is opened too frequently e Door may not be seating properly e Beverage cooler has recently been disconnected for a period of time e Turn the control shaft to a colder setting Allow several hours for temperature to stabilize e Warm air enters the beverage cooler every time the door is opened Open the door less often eSee DOOR PROBLEMS Section e Beverage cooler requires 4 hours to cool down
19. hildren should never use these items to play Cartons covered with rugs bedspreads plastic sheets or stretch wrap may become airtight chambers and can quickly cause suffocation Remove all staples from the carton Staples can cause severe cuts and destroy finishes if they come in contact with other appliances or furniture An empty discarded ice box refrigerator beverage cooler or freezer is a very dangerous attraction to children e Remove and discard any spacers used to secure the shelves during shipping Small objects are a choke hazard to children Remove the door s of any appliance that is notin use even if itis being discarded Proper Disposal of Your Refrigerator Freezer Beverage Cooler PEGON Risk of child entrapment Child entrapment and suffocation are not problems of the past Junked or abandoned refrigerators freezers or beverage coolers are still dangerous even if they will sit for just a few days If you are getting rid of your old freezer refrigerator or beverage cooler please follow the instructions below to help prevent accidents BEFORE YOU THROW AWAY YOUR OLD REFRIGERATOR FREEZER BEVERAGE COOLER Remove doors Leave shelves in place so children may not easily climb inside ELECTRICAL INFORMATION These guidelines must be followed to ensure that safety mechanisms in the design of this beverage cooler will operate properly e Beverage Cooler must be plugged into its
20. ll stn i Do not under any ie circumstances ai cut remove or bypass the Power supply cord with 3 prong grounding plug CO CANISTER SAFE HANDLING CO canisters must be handled with extreme care They contain potentially hazardous high pressure compressed gas ALWAYS connect CO2 gas canisters to a pressure regulator NEVER drop or throw the COz canister NEVER connect gas canister directly to keg ALWAYS keep COs canisters in a cool place 70 or less and away from heat In case of COz2 leakage ventilate and evacuate the area immediately ALWAYS keep canister secured in an upright position Check the Department of Transportation D O T test date on the canister neck and do not use if older than 5 years Return outdated canister to your gas supplier for one that is within the time window FIRST STEPS This Use and Care Manual provides specific assembly operating and maintenance instructions for your model Use the beverage cooler only as instructed in this Use and Care Manual Before starting the beverage cooler follow these important first steps PARTS AND ACCESSORIES Your beverage cooler comes with a box that contains all the parts and accessories needed for your beverage cooler Check to make sure that you have received the box containing all of the components listed below You will need the following tools to assemble the beverage cooler a PHILLIPS SCREWDRIVER i lt _s
21. ng ducts or registers Do not place the beverage cooler next to j heat producing appliances such Ne 1 as a range oven or dishwasher mel wy e Do not overcrowd the beverage cooler or block cold air vents Doing so causes the beverage cooler to run longer and use more energy Shelves should not be lined with CLEANING AND MAINTENANCE aluminum foil wax paper or paper toweling Liners interfere with air circulation making the beverage cooler less efficient CLEANING THE INSIDE Organize the beverage cooler to reduce door openings Remove as many items as needed at one time and close Wash inside surfaces of the beverage cooler with a the door as soon as possible solution of two tablespoons of baking soda in one quart 1 136 liters warm water Rinse and dry Wring excess BEVERAGE COOLER FEATURES water out of the sponge or cloth when cleaning in the area of the controls or any electrical parts ADJUSTABLE INTERIOR SHELVES e Wash the removable parts with the baking soda solution mentioned above or mild detergent and warm water Multi position adjustable interior shelves can be moved to Rinse and dry NEVER use metallic scouring pads any position for larger or smaller packages The shipping brushes abrasive cleaners or alkaline solutions on any spacers that stabilize the shelves for shipping should be surface DO NOT wash removable parts in the dishwasher removed and discarded CLEA
22. oler malfunctioning e Faucets in bad dirty or worn condition eMake sure faucet is opened all the way Close quickly when done e Replace regulator e Readjust regulator to a lower pressure until foam subsides When pressure is properly set you should be able to pour 10 oz of beer in about 5 seconds e Make sure beer delivery line is not pinched and is fully inside the interior of the beverage cooler e Wait until keg cools down to proper temperature e Have beverage cooler serviced to return it to proper operating condition e Thoroughly clean faucet with cleaning kit Replace any worn seals recommended FLAT BEER Foamy head disappears quickly beer lacks usual zestful brewery fresh flavor e Dirty glasses e Applied pressure is set too low e CO is turned off e Beer too cold e Loose tap or vent connections e Sluggish regulator e Wash glasses using soap free detergent e Increase pressure until beer flows at a rate of 2 oz per second e Do not turn off CO2 supply line to keg until keg is empty and ready to be removed elncrease temperature of beverage cooler see SETTING THE TEMPERATURE CONTROL e Check that coupler is properly installed in keg e Replace regulator CLOUDY BEER When beer in glass appears hazy not clear e Frozen or nearly frozen beer e Unrefrigerated beer for long periods of time e Dirty glasses e Dirty faucet e Unrefrigerated foods placed on to
23. p of cold keg eReturn keg to place of purchase and exchange for one that has been properly refrigerated e Exchange keg for fresh one e Wash glasses using soap free detergent e Clean faucet with recommended cleaning kit eRemove items from atop keg and place in a separate refrigerator 12 3 Ways To Contact Us i3 formas de contactarnos 3 fa ons de nous contacter USA EE UU E U 1 800 944 9044 CANADA CANADA 1 866 213 9397 English 1 866 294 9911 Francais Or O Ou USA EE UU E U CANADA CANADA Electrolux Home Products Inc Electrolux Canada Corp P O Box 212378 6150 McLaughlin Road Augusta GA 30917 Mississauga Ontario L5R 4C2 Or O Ou Visit Frigidaire s Web Site At Visite la pagina de Frigidaire en Internet Visitez le site Internet de Frigidaire au http www frigidaire com 2004 Electrolux Home Products Inc 2 The Electrolux Group The world s No 1 choice The Electrolux Group is the world s largest producer of powered appliances for kitchen cleaning and outdoor use combined More than 55 million Electrolux Group products such as refrigerators cookers washing machines vacuum cleaners chain saws and lawn mowers are sold each year to a value of approx USD 14 billion in more than 150 countries around the world
24. the nut with an adjustable wrench Check the condition of the gasket inside the nut and replace if necessary e Return canister to your local carbonic gas source for filling we suggest looking in your yellow pages under Carbonic Gas Sources of COz2 vary from community to community but it is often available at welding supply stores and beverage distributors e Remove dust cap from new canister nut if any BEER STORAGE TEMPERATURE OPTIONAL CASTER KIT e Draft beer is not pasteurized so it must be kept cold If you d like to make your beverage cooler so it can be rolled preferably at 38 F Temperatures above 38 F may cause from room to room there is an optional caster kit available the beer to become wild turn sour and cloudy from your authorized Frigidaire dealer or service center Just ask for part number 297027300 Caster Rail and Hardware TYPICAL BEER SERVING EQUIVALENTS Kit which includes 2 fixed casters 2 swivel casters 2 caster support rails and mounting hardware Vo Keg 15 1 2 Gallons 1984 Fluid Ounces Ye Keg 6 3 4 Cases of 12 ounce bottles Overall weight of full 2 Keg is approximately 165 pounds 14 Keg 7 Gallons 992 Fluid Ounces 4 Keg 3 3 8 Cases of 12 ounce bottles Overall weight of full 1 4 Keg is approximately 82 5 pounds CASTERS ENERGY SAVING TIPS _ e Install the beverage cooler in the a coolest part of the room out of TN direct sunlight and away from xX heati
25. ug housing on top of keg and insert the tap head Hose amp e Turn the tap head handle 4 turn clockwise The tap head E soe is now secured to the keg e Pull the tap handle out and push down to open the port in the keg CONNECTIONS CO CANISTER TO CABINET INSTALLATION GENERAL OPERATION Place the COg2 canister 19 with the regulator 13 inside the CO2 Canister Bracket 4 in the cabinet It is important that the canister be kept in an upright position to operate efficiently Fasten the canister securely in place using the 4 long carriage bolt 6 and wing nut 7 supplied with this The temperature control is located on the back side of the SETTING THE TEMPERATURE CONTROL unit beverage cooler The temperature is factory preset for 19 CO satisfactory storage temperature However the CANISTER temperature control is adjustable to provide a range of temperatures for your personal satisfaction If a colder 6 4 LONG temperature is desired turn the control shaft of the cold 13 Aii ical control clockwise using the tip of the screwdriver as shown E in the diagram below To set the cold control to OFF position turn the control shaft counter clockwise until it P 7 WING NUT stops Allow several hours for the temperature to stabilize BRACKET between adjustments KEG TO CABINET INSTALLATION e Place the keg next to the COs canister 19 inside the cabinet as shown 19 CO2 CANISTER KEG
Download Pdf Manuals
Related Search