Home

Nikon COOLSCAN IV ED LS40

1. cccceeeeeeeee 84 Step 2 Insert the Adapter 00008 84 Step 3 Insert the Slide ccceeeeeeees 85 Step 4 Scan the Slide cccecceeeeeeeeees 86 83 Step 1 Ready the Slide The MA 20 S slide mount adapter is used to scan 35 mm film mounted as slides 35 mm slide Step 2 Insert the Adapter After confirming that the scanner is ready the scanner is ready when the status LED is not blinking insert the MA 20 S slide mount adapter into the scanner Open the sliding cover on the front of the scanner and slide the MA 20 S smoothly into the adapter slot until it is fully inserted The status LED will blink a few times and then glow steadily 84 Step 3 Insert the Slide The MA 20 S scans slides one at a time Insert the slide smoothly with the emulsion surface down shiny surface up and the short side of the slide aperture toward the scanner Stop when the slide contacts the rear of the film slot Compatible Slides Slides scanned in the MA 20 S must have mounts between 1 0 and 3 2 mm thick and from 49 to 50 8 mm in width 85 E Step 4 Scan the Slide The actual scan is performed using Nikon Scan for detailed information on using Nikon Scan see the Nikon Scan 3 Software Manual Making a Scan 1 Start Nikon Scan Windows From the Start menu select All Programs gt Nikon Scan 3 1 gt Nikon Scan 3 1 Windows XP or Programs gt Nikon
2. A Pee OO Ne T Hh IH HULL PEP EE eee ri I ay Frame scanned Frame 2 Frame 3 Frame scanned Frame scanned ri raph ff fe F Frame scanned Frame 4 110 Frame 5 Frame 6 Using the SA 21 The SA 21 can be used to scan 35 mm film in strips of two to six frames for information on film that can not be used in the SA 21 see pages 102 104 of this manual 35 mm film in strips of two to six frames 1 After confirming that the scanner is ready the scanner is ready when the status LED is not blinking insert the SA 21 into the scanner Open the sliding cover on the front of the scanner and slide the SA 21 smoothly into the adapter slot until it is fully inserted The status LED will blink a few times and then glow steadily V4 Removing the Adapter Attempting to remove the adapter without ejecting the film can result in the adapter becoming separated from the connectors at the rear of the adapter slot interfering with scanning If you have attempted to remove the adapter before ejecting film push the adapter back into the slot slightly to ensure that the connection is not interrupted Do not attempt to remove the adapter by force as this could damage both the adapter and scanner 111 To prevent the film from curling hold it lightly by both edges with the emulsion surface down s
3. UO AE o gt O U Ei 80 Confirm that the scanner is working properly Double click the listing for your scanner that appears under Imaging Device The scanner Properties dialog will be displayed Click the General tab and confirm that This device is working properly appears under Device Status If another message is displayed proceed to Updating the Device Driver Windows 98 SE on 81 Nikon COOLSCAN I ED Properties Updating the Device Driver Windows 98 SE If the scanner is not listed under Imaging Device in the Device Manager or the message This device is working properly does not appear in the Properties dialog you will need to reinstall the device driver as detailed below 1 Open the scanner Properties dialog Display the Device Manager as described in steps ENNI Bz ES 1 3 of Confirming Device Registration Windows m mamma 98 SE GJ 79 If the scanner is listed under Other Pisaca oa EE acer a devices or appears next to a x Ai Nas He S 1394 Bus Controller 3 CDROM amp Disk drives a Display adapters Sy Floppy disk controllers Sy Hard disk controllers 3 Keyboard 3 Modem 5 Monitors A Mouse pa 2 Or x double click the entry for the scanner to display the scanner Properties dialog DRE H 6 E Other devices E Nikon COOLSCAN I ED 2 Click Reinstall driver Open the
4. Ing Device proceed to Updating the z Hard disk controllers i Fy H Imaging Device Device Driver Windows Me E 48 Jg PYDI E Monitors A Mouse g7 Network adapters D Other devices a Ports COM amp LPT g SBP2 DRT Properties Refresh Remove Print Cancel 46 D Confirm that the scanner is working properly F Double click the listing for your scanner Nikon SUPER COOLSCAN 4000 ED Proper 2jxi that appears under Imaging Device The i scanner Properties dialog will be displayed Click the General tab and confirm that This device is working properly appears re under Device Status If another mes e ae PEAR sage IS displayed proceed to Updating Hardware version Not available the Device Driver Windows Me EJ 48 Device status This device is working properly General Driver Nikon SUPER COOLSCAN 4000 ED m Device usage V Exists in all hardware profiles aq 0007 47 i Updating the Device Driver Windows Me 4000 ED If the scanner is not listed under Imaging Device in the Device Manager or the message This device is working properly does not appear in the Properties dialog you will need to reinstall the device driver as detailed below 1 Open the scanner Properties dialog Display the Device Manager as described in steps 1 3 of Confirming Device Registration Windows Me
5. If a list of drivers is displayed select the driver EZEOmIA i xl with the path ending in LS 40M E IN F and yee Holes Utes pee that may work for your hardware Please select the driver that click OK on COOLSCAN IV ED F SINFSLS40 WINMESLS40ME INF 3 5 2001 aJ Al NVDS1009 Ooo Cancel D Click Finish Click Finish to complete installation If prompted to restart the computer click Yes Add New Hardware Wizard 2 Nikon LS 40 ED Windows has finished installing the software you selected that your new hardware device requires Cancel 6 Confirm device registration Confirm that the scanner has been correctly registered with the system as described in Confirming Device Registration Windows Me J 72 73 75 7 Windows 98 Second Edition SE Registering the Scanner with Windows 98 SE COOLSCAN IV ED 1 Turn the scanner on The first time the computer detects the scanner Windows will display the dialog shown at right Click Next 2 Insert the Nikon Scan 3 CD Holding down the shift key to prevent the Welcome program from starting automati cally insert the Nikon Scan 3 CD into the CD ROM drive Select the search option and click Next The Welcome Window If the Welcome program starts automatically when you insert the Nikon Scan CD click Exit to close the Welcome window 76 Add New Hardware Wizard This wizard searches for new drivers for LS 40 ED device driver i
6. Q Thumbnail drawer tab Click to select frames to be scanned from multi frame film Preview area The preview image is displayed here Tool chest Contains tools for e setting the image orientation and choosing the portion of the image to be scanned e controlling the physical dimensions and file size of the image when opened in the host application e enhancing color contrast and sharpness e removing the effects of scratches dust fading and film grain e controlling scanner settings Scan Progress window Shows what actions are being performed and gives a log of automated tasks 121 7 The Control Area Eject Button Proc Pst Ejects film ion ies scanner Autoexposure Button Before scanning the scanner needs to gather information about the image to adjust expo sure for best results Click this button to adjust exposure Settings Menu Sethings _ Callbrated HGR o gt Using the options in this menu you can reset the scanner to default settings or save scanner settings suited to particular scanning conditions and recall them as desired 122 ahi Button Click to focus the scanner on the center of the image or control click Windows or option click Macintosh to select a new focus point Zoom Buttons Click the 58 button to zoom in on the current crop enlarging it to fill the preview area Click the button to zoom out Media Type Menu Weg Cola w
7. Wizard Macintosh There are three choices of color spaces here 1 Apple RGB 2 Color Match RGB 3 Apple RGB compensated 1 gives you the most vivid color reproduction However it may be too saturated in places 3 maintains the most tonal information possible but it may look flat 2 represents values between these two extremes Please choose one and press the OK button Apple RGB 2 COIT Match RGB Apple RGB compensated A sample image is being displayed using the selected color space profile If you think that all color spaces are still too dark press the too Dark button 23 o E 9 24 Nikon Scan 3 can be used to scan images directly into any application that supports Adobe Photoshop 5 0 acquire plug ins The installer will display a list of plug in folders for the applications currently in stalled on your computer choose the fold ers containing Adobe Photoshop plug ins and click OK to copy the Nikon Scan 3 1 plug in to the selected folders Click Can cel to complete installation without creat ing a copy of the Nikon Scan 3 1 plug in A dialog will be displayed stating that in stallation is complete Click Restart to re start your computer Mac OS 9 or earlier or Quit to exit the installer Mac OS X This completes installation of Nikon Scan 3 Select Folder T E Macintosh HD S Adobe Photoshop 6 0 J SY Plug Ins Inst
8. albrated HOGE _ _ w Adjusts scanner settings to match the media in the scanner Select positive when scanning film positives slides reversal film or mono chrome positives negative color or mono chrome when scanning negatives A separate option is available for scanning Kodachrome positives Color Model Menu Window Buttons Calibrated HGE wY Select a color model according to the capaci ties of your image editing software and Help click to open the Nikon Scan help file whether the image is destined for output ona Tools click to open the Tool Chest or Scan commercial four color printing press or display Progress windows on a monitor 123 7 The Information Panel Orientation File Size B7 7 ME AnalogG ain Neutral Dimensions File Size File Size 67 27 MB Aha Jil I WELL l E l gital R OC Neutral Shows the orientation of the preview image relative to the original reflecting any flips or rotations that have been performed Image Enhancement File Sine ET OF MP AnalogGain Neutral Digital ROC Neutral Digital GEM Neutral Digital ICE Off Mult ample 1 Indicates whether Digital ICE and analog gain are in effect Remember to use Digital ICE only when needed as turning Digital ICE on can substantially increase scanning times Color Values Bit Depth 8 Gives the color values for the pixel under the cursor in the Natural tab top row or Processed
9. Apertures J After confirming that the scanner is ready the scanner is ready when the status LED is not blinking insert the MA 20 S slide mount adapter into the scanner v Inserting the MA 20 S Open the sliding cover on the front of the scanner and slide the MA 20 S smoothly into the adapter slot until it is fully inserted The status LED will blink a few times and then glow steadily 108 Insert the aperture containing the frame you want to scan into the MA 20 S 9 Scan the frame as described on pages 86 98 of this manual Insert the aperture containing the frame you want to scan into the MA 20 S 1 0 After scanning wait for the status LED to stop blinking and then remove the FH 3 from the film slot by hand Do not use the eject button on the MA 20 S You can now turn the scanner off as described on page 100 of this manual v Using the Film Holder Do not use force when inserting the holder as this could damage the holder or the scanner To avoid damage to the film remove dust and lint from the film holder before use Dust and lint can affect the quality of scanned images and damage your film Do not use the eject button on the MA 20 S when removing the FH 3 Remove the FH 3 by hand 109 Scanning Frames in Order The position of the frame scanned is shown in the diagram below Direction of insertion a Frame scanned pe h M igi Wy Wi f UUU II
10. Manager click the to its left to view General Device Manager Hardware Profiles Perfomance the imaging devices currently registered f View devices by type View devices by connection with Windows Confirm that your scan ner IS listed H Se 1394 Bus Controller 2 CDROM If the Scanner Is Not Listed eke play adapters If your scanner is not listed under Imag 2S Floppy disk controllers ing Device proceed to Updating the imaa esio Device Driver Windows 98 SE R9 55 le EEA d Modem m Monitors Mouse Network adapters a Other devices i gt rc sige socket gt sbe IONLI O EMT Properties Refresh Remove Print Cancel 53 4000 ED 5 54 Confirm that the scanner is working properly Double click the listing for your scanner that appears under Imaging Device The scanner Properties dialog will be displayed Click the General tab and confirm that This device is working properly appears under Device Status If another message is displayed proceed to Updating the Device Driver Windows 98 SE on 55 Nikon SUPER COOLSCAN 4000 ED Properties General Driver Nikon SUPER COOLSCAN 4000 ED Device type Imaging Device Manufacturer Nikon Corporation Hardware version Not available Device status This device is working properly Device usage Tags tee eneeseneeenesenecsesen
11. five seconds and then turn it back on Adapter slot This is where you put adapters for different types of film Don t put anything in this slot except an approved Nikon film adapter Sliding cover Slide the cover down before inserting a film adapter To protect your scanner from dust and other foreign objects be sure Aways to close the cover when no adapter is in place 4000 ED COOLSCAN IV ED tJi i O COOLSCAN IV ED 6 Power switch Press this switch to turn the scanner on and off Film gate for optional SA 30 roll film adapter 4000 ED Open this gate only when you are using the SA 30 roll film adapter available separately AC connector Connect the female end of the power cable here IEEE 1394 Firewire interface connector 4000 ED Connect the IEEE 1394 Firewire interface cable here O Feet Always place the scanner on one of its two sets of feet USB interface connector COOLSCAN IV ED Connect the USB interface cable here Accessories After unpacking the scanner check that the package contains all the items listed below Con tact your retailer immediately should you find that anything is missing or damaged Power cable 1 shape of cable depends on country of sale IEEE 1394 Firewire interface cable 1 4000 ED only Use this cable to connect the 4000 ED to your computer MA 20 S slide mount adapter 1 Use this adapter to scan mounted slides or with the F
12. tab bottom row 124 E l gital A OC Neutral Gives the height and width of the current crop in pixels and the size of the file that will result if the crop is scanned at the current output size and resolution Scanner Extras Digital ICE Off Mult ample Ts Bit Depth 3 Displays the current bit depth which deter mines the maximum number of colors in the image When the 4000 ED is connected it also indicates whether multi sample scanning is in effect The Preview Button The Scan Button Clicking this button displays a preview of the Scans the image and opens it in the host appli image to be scanned if multiple frames are cation if multiple frames are selected in the selected in the thumbnail drawer a preview will thumbnail drawer each frame will be scanned be performed for each frame You will need and opened in a separate window to create a new preview after changing the me dia type or using the zoom buttons The Thumbnail Drawer Tab 1500 This tab is only displayed when a multi frame adapter such as the SA 21 is inserted in the scanner Clicking this tab opens the thumbnail drawer where you can select the frame to be scanned by clicking the associated frame number To view the frames as small previews thumbnails click the button Multiple frames can be selected by clicking each frame in turn while holding down the control Windows or command Macintosh key or by holding down the shift
13. CJ Nederlands Francais Nederlands S My Computer Q My Documents Shared Documents E My Network Places INDEX pdf S Adobe Acrobat Document da pa nese Details 19 KB NIKON 0 CD Drive vi PDF Japanese Windows Macintosh v Important When installing Nikon Scan be sure to exit all other programs including virus checking software and Adobe Acrobat Reader If desired before installing Nikon Scan you can print the Getting Started section of the software manual which details the installation process 119 Ba The Scan Window The Parts of the Scan Window l Tool Palette 1 Segilolai a F ee z b Layout Tools Calibrted AGE _ w b Information P Crop b Curves Color Balance b LCH Editor b Unsharp Mask Digital ICE cubed AnalogGair Neutr Digital ROC Neutral Analog Gain Digital GEM Neutral b Scanner Extras Digital ICE Off altis ample 1 Bit Depth 8 Progress Window No scanning tems es o 120 A Control area Contains the most frequently used scanning and preview controls Information panel Provides information on current scan settings Preview button Click to preview the frame to be scanned The preview shows how the image will look when it is scanned Scan button Click to scan the selected portion of the image into the host application Q Interactive help Gives a brief tip about the control under the mouse cursor
14. HOME OR OFFICE USE sures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio television technician for help CAUTIONS Nikon 4000 ED C Tested To Comply With FCC Standards C Tested To Comply With FCC Standards Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Nikon Corporation may void the user s authority to operate the equipment Interface Cables Use the interface cables sold or provided by Nikon for your equipment Using other interface cables may exceed the limits of Class B Part 15 of the FCC rules Nikon Inc 1300 Walt Whitman Road Melville New York 11747 3064 U S A Tel 631 547 4200 Notice for customers in Canada CAUTION This class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations ATTENTION Cet appareil num rique de la classe B respecte toutes les exigences du R glement sur le mat riel brouilleur du Canada Notice Concerning Prohibition of Copying or Reproduction Note that simply being in possession of material that has been digitally copied or reproduced by means of a scanner digital camera or other device is punishable by law e Items prohibite
15. Neutral Digital ICE Off MultiS ample 1 Bit Depth 8 R G Preview area 88 D Adjust scan settings For steps 6 through 10 you will use the tools in the Tool Chest The Tool Chest is a window of tool palettes each containing controls for a specific task such as selecting the area to be scanned adjusting contrast color and sharpness setting the scan size and resolution or compensating for defects in the original such as grain or fading If the Tool Chest is not already open you can display the Tool Chest by clicking the Tools button in the scan window and selecting Tool Palette 1 from the menu that appears Settings F albrated PGE _ w Tools button Mikon SUPER COOLSCAN 4000 ED 1 00 3 EEET S34 SnalogGain Neutral Scan Progress Yata ROL Neutra Tool Palette 1 gt Layout Tools yore gt w Curves b y Color Balance Z A LEN paito gt Unsharp Mask gt Digital ICE cubed gt Analog Gain Scanner Extras Tool Palette 1 Pg For more information on 40 The Tool Chest og 89 n 6 Rotate or flip the image If necessary you can rotate or flip the preview image Click the triangle at the top left corner of the Layout Tools palette in the Tool Chest to view the controls in the Layout Tools palette In this example the Kad button is used to rotate the image 90 to the right Click T ol Palette 1 7 Layout Tools m oE ael 5 41 M Show
16. Scan 3 1 gt Nikon Scan 3 1 other versions of Windows uy Dar tup fay Nikon Scan 3 1 gt faa Nikon Scan 3 1 Internet Explorer EX Nikon Scan 3 1 Help we MSN Explorer A Nikon Scan 3 1 ReadMe A Outlook Express j5 Mikon Scan 3 1 Uninstall r Remote Assistance Windows Media Player 33 Windows Messenger m ArcSoft Panorama Maker gt M Nikon Capture 3 gt All Programs m QuickTime gt Log Off Turn OFF Computer Nikon Scan f start Mac OS X Open the folder Applications Nikon Software Nikon Scan 3 on the startup disk and double click the Nikon Scan 3 icon Nikon Scan 3 Mac OS 9 or Earlier Open the Nikon Software folder in the location to which you installed Nikon Scan the default location is the root directory of the startup disk and double ss click the Nikon Scan 3 1 icon Nikon Scan 3 1 Scanning Images into Other Applications Nikon Scan can be used as a Stand alone application for scanning images and saving them to disk as described above It can also be used to scan images directly into any application that supports TWAIN Windows or Adobe Photoshop 5 0 acquire plug ins Mac OS 9 or earlier Nikon Scan can not be used to scan images into third party applications in Mac OS X Windows Select Nikon Scan from the application s list of Acquire or Import sources Mac OS 9 or Earlier Before starting the application make
17. The button will change to ml click the button again to return to the frame number display Click here to display and hide thumbnails WeolCalarl CLalbrated HGE Y Thumbnail area 113 Using the Thumbnail Drawer Continued If the thumbnail drawer is too small to display all frames at once you can enlarge the drawer by dragging the lower right corner or use the scroll bar to view frames that can not be displayed in the drawer Scroll bar Wea lolol 3 albrated RGE YF Drag to enlarge thumbnail area The frame to be scanned can be selected by clicking the associated frame number or thumbnail To select multiple frames hold down the Ctrl Windows or command Macintosh key while clicking frames one at a time or hold down the shift key while clicking two images to select these images and all frames between them Selected thumbnail nail Heg Colal wY albrated PGE w Preview and scan the selected frames en 88 97 114 4 Once scanning is complete you can exit Nikon Scan and turn the scanner off 4 1 Eject the film Click the eject button in Nikon Scan to eject i the film from the scanner 5 ge a Hegleo 4 2 Remove the film adapter Slide the film adapter from the adapter slot a yy v Ejecting Film The SA 21 is equipped with a locking mechanism that prevents the adapter from being removed while film is in place Before removing the SA 21 from th
18. Turn the scanner off COOLSCAN IV ED Wait for the status LED to stop blinking then press the power button to turn the scan ner off 4000 ED If you are using a Macintosh or a computer running Windows XP or Windows 2000 Professional wait for the status LED to stop blinking and then turn the scanner off by pressing the power button If you are using Windows Me or Windows 98 SE you must first remove the scanner from the system as described below Windows Me Shut down the computer Once the computer has turned off press the power button to turn the scanner off Windows 98 SE Click the Unplug or Eject Hardware button in mermera the taskbar and select Stop Nikon SUPER ro Eg J COOLSCAN 4000 ED from the menu that ap pears A message will be displayed stating that the scanner can be safely removed from the system click OK and follow the on screen instructions to terminate the transfer of data between the scanner and the computer You can then turn the scanner off by pressing the power button If you fail to perform this step before dis con necting the scanner or turning it off the You have unplugged or ejected a device without stopping it which i F K can cause your computer to crash and lose valuable data dialog shown at right will be displayed A Please use the hotplug icon in the status bar to safely stop devices before unplugging them Scanning 35 mm Film This chapter describes how to scan strips of
19. a hardware device work Windows needs driver files for your new device To locate driver files and complete the installation click Next What do you want the wizard to do Search for a suitable driver for my device recommended Display a list of the known drivers for this device so that can choose a specific driver lt Back vee Cancel Log on as the Administrator when registering the scanner The Welcome Window If the Welcome program starts automatically when you insert the Nikon Scan CD click Exit to close the Welcome window 36 pj Welcome Copyright 1998 2001 Nikon Inc and Nikon Corporation GR _ Nikon Scan 3 HR Reade Ba Zit hitp www Nikon Asia com hitip www Nikon Eure com http www Nikon USA com 3 Select Specify a location Select Specify a location and click Next 4 Click Browse When the dialog shown at right Is dis played click Browse D Select the Win2000 folder The Locate File dialog will be displayed Select the Nkscan CD from the Look in menu and open each of the INF LS4000 and Win2000 folders in turn Select the file LS40002K INF and click Open Found New Hardware Wizard 7 Locate Driver Files Where do you want Windows to search for driver files SY Search for driver files for the following hardware device oy Nikon LS 4000ED IEEE 1394 SBP2 Device The wizard searches for suitable drivers in its driver database on your computer
20. all other devices that use same interface as the scanner e Re install Nikon Scan The status LED flashes rapidly scanner connected to computer Oo 148 e Update the device drivers for the USB or IEEE 1394 a Firewire interface Windows only e Update the device drivers for your scanner Windows kam only 23 e The film is not properly inserted Eject and re insert film e The film was moved during scanning or scanner was subjected to shock or vibration Do not use the scanner where it will be subject to shock or vibration Failure to observe this precaution could result in malfunction e Settings are improperly adjusted in Nikon Scan Refer to the Nikon Scan 3 Software Manual for information on adjusting scanner settings or try resetting scanner set tings to factory defaults L 0p LIN The quality of scanned images is poor sO 131 e The scanner is off 7 Turn the scanner on 28 e The scanner was turned on with the FH 3 film holder inserted in the adapter slot 105 After removing the FH 3 turn the scanner off and then on again e The interface cable is not properly connected aa After confirming that the scanner is off reconnect the cable 25 e Another device or program using the same interface conflicts with the scanner or Nikon Scan 148 Remove all other hardware connected to the same bus as the scanner If the scanner is connected to a hub exten sion cable or other adapter disconnect the adapter a
21. and in any of the following optional search locations that you specify To start the search click Next If you are searching on a floppy disk or CD ROM drive insert the floppy disk or CD before clicking Next Optional search locations I Floppy disk drives IV Specify a location Ww ndate lt Back Next gt Cancel Found New Hardware Wizard f aq 0007 Insert the manufacturer s installation disk into the drive selected and then click OK Cancel Copy manufacturer s files from z Browse Locate File alxi Look in ay Win2000 E 40002K INF he File name Files of type Setup Information inf 37 4000 ED 6 Confirm the file path The dialog shown at right will be dis x p a y e d g C on f rm t h a t t h e p a t h Insert the manufacturer s installation disk into the drive oe INF LS4000 Win2000 appears after the a selected andthe elek OK drive letter of the CD ROM drive and click OK If the Correct Path Is Not Displayed E E E If the correct path is not displayed repeat GHINF LS4000 win2000 Browse steps 4 6 to select the correct path 7 Begin installation of the device drivers Click Next Driver Files Search Results Pua Rant The wizard has finished searching for driver files for pour hardware device SY The wizard found a driver for the following device oy Nikon LS 4000ED IEEE 1394 SBP2 Device Windows fo
22. grid el t gt Information O OOOO O Crop F The image in the preview area can be rotated and flipped using the following four buttons lele lab Rotate the image ninety degrees to the right Rotate the image ninety degrees to the left Flip the image horizontally Flip the image vertically Any flips and rotations performed on the image are reflected in the orientation of the letter R in the Layout Tools palette l Pg 43 90 For more information on The Layout Tools palette Compensate for defects Click the triangle at the top left corner of the Digital ICE cubed Digital ICE palette in the Tool Chest to view the controls in the Digital ICE cubed palette for more information on Digital ICE see page 51 of the Nikon Scan 3 Software Manual Click 7 Digital ICE cubed W Enable Digital ICE Normal M Enable Post Processing Digital ROC 4 gt 0 Digtal GEM 4 Redraw To remove dust and scratches from the image check Enable Digital ICE and select Nor mal or Fine from the Digital ICE menu A setting of Fine can be used to remove very fine scratches or barely visible dust although this may sometimes result in reduced sharpness To restore faded colors or reduce the effects of film grain first check Enable Post Pro cessing Faded colors can be restored adjusting the Digital ROC for Restoration of Color slider while the image can be processed to minimize g
23. listed z r ee adapters 29 DYDICD ROM drives If the Scanner Is Not Listed nals eas i 9 Floppy disk drives If your scanner is not listed under Imag H IDE ATA ATAPI controllers ing devices proceed to Updating the SW Imaging devices Device Driver Windows 2000 Profes J Nikon COOLSCAN IV ED sional gJ 68 ae D Mice and other pointing devices Monitors 8 Network adapters Other devices a7 Ports COM amp LPT g Sound video and game controllers m System devices Universal Serial Bus controllers 4 0 4 4 4 66 D Confirm that the scanner is working properly F Double click the listing for your scanner 2x that appears under Imaging devices The scanner Properties dialog will be dis played Click the General tab and con firm that This device is working properly appears under Device Status If another ee eee message is displayed proceed to Updat eiie UNG ing the Device Driver Windows 2000 Pro fessional EQ 68 General Driver Nikon COOLSCAN IV ED Device type Imaging devices Device status This device is working properly YOU are having problems with this device click Troubleshooter to start the troubleshooter Troubleshooter Device usage Use this device enable ad di Al NVDS1009 67 COOLSCAN IV ED Updating the Device Driver Windows
24. m m f y A Th e N ko nN Sca nN 3 1 7 3 WI nN d OW WI ope nN Back View i Computer Home Favorites Applications on the desktop Double click the Nikon Scan Installer icon for the language of your choice ci 3 Nikon Scan Installer OS8 6ANDOS9ONLY Items Memory Requirements under Mac OS X Running Nikon Scan 3 1 3 under Mac OS X requires a minimum of 256 MB of memory of which 128 MB are required by the operating system and the remainder by Nikon Scan 3 1 3 21 E 22 When the installer starts click Con tinue to display the license agreement Clicking Accept displays the ReadMe file Take a few moments to read this file which may contain important information that could not be included in this manual After reading the file click Continue Choose a location for Nikon Scan from the Install Location menu and click In stall Mac OS X Nikon Scan will automatically be installed to the folder Applications Nikon Soft ware on the startup disk You can not select an alternate location Copyright 1998 2001 Nikon Inc and Nikon Corporation Digital ICE cubed TM Digital ICE TM Digital ROC TM and Digif he Ti h trademarks of Applied Science Fiction Ine s Vi Digital ICE cubed TM Digital ICE TM Digital ROC TM and Digital Technology are developed by Applied Science Fiction Inc Adobe is a registered trademark and Photoshop is a trademark of Adobe Systems inc This installation was c
25. tested with Windows and that the software has not been altered since it was tested The software you are about to install does not contain a Microsoft digital signature Therefore there is no guarantee that this software works correctly with Windows Nikon LS 40 ED gt If you want to search for Microsoft digitally signed software visit the Windows Update Web site at http windowsupdate microsoft com to see if one is available Do you want to continue the installation Yes No More Info 64 The dialog shown at right willbe displayed a F while Windows registers the scanner Hardware Install Windows is installing drivers for your new hardware Nikon LS 40 ED Lae Installing software necessary to support your hardware 6 Click Finish Click Finish to complete installation Found New Hardware Wizard Completing the Found New Hardware Wizard Nikon LS 40 ED Windows has finished installing the software for this device The hardware you installed will not work until you restart your computer di Al NVDS1009 To close this wizard click Finish J Restart the computer Click Yes to restart the computer 8 Confirm device registration Confirm that the scanner has been correctly registered with the system as described in Confirming Device Registration Windows 2000 Professional en 66 65 m Confirming Device Registration Wind
26. you purchased your scanner you may be prompted to select the language in which Nikon Scan s menus and dialogs will be displayed Choose a language from the list provided Copyright 1998 2001 Nikon Inc a i HR ENGLISH Ge FRENCH G GERMAN GN sPAnisH Ga BACK hitp vww Nikon Asia com http www Nikon Eure com hittp www Nikon USA com 2 The InstallShield Wizard will start Click Nikon Scan 3 1 Setup Next The license agreement will be dis i Welcome to the InstallShield Wizard for Nikon played click Yes to accept the agreement Sean 3 1 and continue with installation The InstallShield Wizard will install Nikon Scan 3 1 on your computer To continue click Next _New gt _ Cancel If the Welcome Dialog Is Not Displayed If the Welcome dialog is not displayed when you insert the CD into the CD ROM drive double click the My Computer icon click with the right mouse button on the icon corresponding to the drive containing the Nikon Scan 3 CD and select Autorun from the menu that appears iV Windows XP Windows 2000 Professional Installing Nikon Scan under these operating systems requires administrator privileges When installing Nikon Scan under Windows XP log in as the Computer administrator Under Win dows 2000 Professional log in as the Administrator 18 Click Next to install Nikon Scan 3 to the Nikon Scan 3 4 Setup folder for Nikon Scan 3 shown under In a Suupue unlile stall Location
27. 169 x 315 mm 3 66 x 6 65 x 12 40 W x H x D Weight Approximately 3 kg 6 Ib 11 1 oz accessories not included Installation Vertical Horizontal Vertical installation not possible with optional SF 200 S slide feeder t Horizontal installation not possible with optional SA 30 film roll adapter 145 7 COOLSCAN IV ED LS 40 ED Film e35 mm film Positive and negative film both color and monochrome may be used Film may be scanned in strips of up to six frames or mounted as 35 mm slides using mounts of from 1 0 to 3 2 mm in thickness and 49 0 50 8 mm in width e APS IX240 film APS film cartridges can be scanned with the optional IA 20 S adapter for APS IX240 film e Prepared slides Prepared slides can be scanned using the op tional FH G1 slide holder for the MA 20 S Aperture 25 1 x 36 8 mm when scanning 35 mm film in the MA 20 S or FH 3 S 25 1 x 38 0 mm when scanning 35 mm film in the SA 21 18 6 x 28 4 mm when scanning APS IX240 film Scan range 2870 x 4203 pixels when scanning 35 mm film in the MA 20 S or FH 3 S 2870 x 4332 pixels when scanning 35 mm film in the SA 21 2120 x 3237 pixels when scanning APS IX240 film Effective aperture 23 3 x 36 0 mm when scanning 35 mm film in the SA 21 24 0 x 36 0 mm when scanning 35 mm film in the FH 3 S 25 1 x 36 8 mm when scanning 35 mm film in the MA 20 S 16 1 x 26 9 mm when scanning APS IX240 film Effective scan range 2657 x 4104 pixels when scan
28. 2000 Professional If the scanner Is not listed under Imaging devices in the Device Manager or the message This device is working properly does not appear in the Properties dialog you will need to reinstall the device driver as detailed below 1 Open the scanner Properties dialog Display the Device Manager as described in steps 1 3 of Confirming Device Registration Windows 2000 Professional on 66 If the scanner is listed under Other devices or appears next to a or x double click the entry for the scanner to display the scanner Properties dialog 2 Click Update Driver Open the Driver tab and click Update 2 xj Driver nn General Driver Nikon COOLSCAN IV ED Driver Provider Nikon Corporation Driver Date Not available Driver Version Not available Digital Signer Not digitally signed To view details about the driver files loaded for this device click Driver Details To uninstall the driver files for this device click Uninstall To update the driver files for this device click Update Driver Uninstall Update Driver OK Cancel Click Next When the Upgrade Device Driver Wizard is displayed click Next Upgrade Device Driver Wizard Welcome to the Upgrade Device Driver Wizard This wizard helps you upgrade a device driver for a hardware device To continue click Next Cancel 68 4 Select the search option Select the search o
29. 3 Strip Fitm HOLDER Film Dimensions Weight Operating Mode SA 217 Strip FiLM ADAPTER 148 Film Feed Mechanism Power Source Dimensions Weight Operating Mode Mounted 35 mm slides 1 0 3 2 mm in thickness 70 x 49 x 158 mm 2 77 x 1 93 x 6 22 W x Hx D Approximately 100 g 3 6 oz Can be used in both vertical and horizontal installations 35 mm film of one to six frames color or monochrome positive or negative 262 0 x 4 7 x 50 5 mm 10 31 x 0 18 x 1 99 W x H x D Approximately 40 g 1 43 oz Can be used with the MA 20 S slide mount adapter in both vertical and horizontal installations 35 mm film of two to six frames color or monochrome positive or negative Automatic feed with built in motor Supplied from scanner 80 x 70 x 230 mm 3 15 x 2 76 x 9 06 W x Hx D Approximately 500 9 1 Ib 1 86 oz Can be used in both vertical and horizontal installations Specifications for Optional Adapters Some optional adapters can be used with both the 4000 ED and COOLSCAN IV ED while others are exclusively for use with the 4000 ED IA 20 S IX240 Fitm Apapter 4000 ED and COOLSCAN IV ED Film Developed APS IX240 film cartridges of 15 25 and 40 frames Feed Mechanism Automatic feed with built in motor Power Source Supplied from scanner Dimensions 84 x 59 x 208 mm 3 31 x 2 32 x 8 19 WxHxD Weight Approximately 270 g 9 6 oz Operating Mode Can be used in both vertical and horizontal installations SA
30. 30 Fitm Rott Apapter 4000 ED Only Film Rolls of 35 mm film of from two to forty frames color or mono chrome positive or negative Feed Mechanism Automatic feed with built in motor Power Source Supplied from scanner Dimensions e Adapter 80 x 70 x 230 mnm7 3 15 x 2 76 x 9 06 WxHxD e Take up reel 90 x 160 x 230 mm 3 54 x 6 30 x 9 06 WxHxD Weight e Adapter Approximately 500 g 1 Ib 1 86 oz e Take up reel Approximately 500 g 1 Ib 1 86 oz Operating Mode Can only be used in a vertical installation SF 200 S Stipe FEEDER 4000 ED Only Film Mounted 35 mm slides 1 0 3 2 mm in thickness 49 50 8 mm in width Number of slides Approximately 50 slides with a thickness of 1 5 mm Housing Space Approximately 78 5 mm Feed Mechanism Automatic feed with built in motor Power Source Supplied from scanner Dimensions 142 x 85 x 325 mm 5 59 x 3 35 x 12 80 W x Hx D Weight Approximately 770 g 1 Ib 11 50 oz Operating Mode Can only be used in a horizontal installation 149 7 Index A PCCOSS ONES adeceicicchescecocsncsceactckventewiesscuciees 4 147 OP UON al nc sccsatececetecencessceutiaicadte 143 144 149 Adapter film OS essence tes teeters ee teenenceices 143 148 MA 20 S cecceeceeeceeeeeeeneeeeeees 4 84 105 147 SA 21 aaiae 4 102 111 133 139 147 SARO aE A 144 148 SF 200 S geceeteee eee eet eet 144 148 Application ICON sii ee seunseitetaterrategammn cnn 21 118 AUtOeEXpOSUT e sac cssnsscccceasdesas
31. 35mm 1X240 Fim Scanner SUPER COOLSCAN 4000 EF 35mm 1IX240 Film Scanner COOoLSCaAan ITV EF User s Manual Device Registration Windows Only Scanning 35 mm Film Reference Scanning Guide Install Nikon Scan scanner driver software The procedure for installing the software Windows See 16 differs depending on whether you are us ing a Windows or Macintosh computer Macintosh See 21 Set up the scanner and connect it to your computer Windows users will need to register the scanner with Windows when con necting the scanner for the first time Connect the scanner to the computer Connect the scanner See 25 Registration of the scanner as a new de vice is necessary only under Windows Register the scanner See ag Insert a film adapter and insert film into the scanner The adapter used depends on the media scanned Slides Use the MA 20 S See 83 Film that cannot be gt Use the FH 3 film holder scanned in the SA 21 with the MA 20 S see 102 Film strips of two to 4 PRE Use the SA 21 See ale Scan the film using Nikon Scan Basic scanning See 86 The scan window See 120 Product Documentation The documentation for this product includes the manuals listed below Please be sure to read all instructions thoroughly User s Manual this manual This User s Manual is intended for use with both Nikon SUPER COOLSCAN 4000 ED referred to below as the 4000 ED and Nikon COOLSCAN IV ED film scanners and
32. 4000ME INF Select LS4000ME INF in the list of drivers and click OK LS4000ME INF Several drivers with similar names may be displayed Be sure to select LS4000ME INF The Welcome Window If the Welcome program starts automatically when you insert the Nikon Scan CD click Exit to close the Welcome window 44 Add New Hardware Wizard Windows has found the following new hardware Nikon LS 4000ED IEEE 1394 SBP2 Device Windows can automatically search for and install software that supports your hardware If pour hardware came with installation media insert it now and click Next What would you like to do Specify the location of the driver Advanced Cancel Select Other Driver p x Windows has found more than one driver that may work for your hardware Please select the driver that matches your language and device Driver Date 3 5 2001 Location H AINFALS40005 WINMESLS4000ME INF _Driver Description Nikon SUPER COOLS ply Welcome Copyright 1998 2001 Nikon Inc and Nikon Corporation GE Viikon Scan 3 GR ReadMe Zit http www Niken Asia com hitp www Niken Euro com hitp www Nikon USA com Click Finish F Click Finish to complete installation Add New Hardware Wizard s Nikon SUPER COOLSCAN 4000 ED Windows has finished installing the software you selected that your new hardware device requires Cancel Restart t
33. Click Finish When the wizard displays a message stat EIEEE ing that it has found the drivers for your scanner click Finish to complete installa tion If prompted to restart the computer click Yes Completing the Found New Hardware Wizard D Nikon LS 40 ED Windows has finished installing the software for this device The hardware you installed will not work until you restart your computer To close this wizard click Finish J Confirm device registration Confirm that the scanner has been correctly registered with the system as described in Confirming Device Registration Windows 2000 Professional on 66 67 69 7 Windows Millennium Edition Me Registering the Scanner with Windows Me COOLSCAN IV ED 1 Turn the scanner on The first time the computer detects the scanner Windows will display the dialog shown at right 2 Insert the Nikon Scan 3 CD Add New Hardware Wizard Windows has found the following new hardware Nikon LS 40 ED Windows can automatically search for and install software that supports your hardware If your hardware came with installation media insert it now and click Next What would you like to do Specify the location of the driver Advanced Cancel Holding down the shift key to prevent the Welcome program from starting automatically insert the Nikon Scan 3 CD into the CD ROM drive Select the search option Select the search optio
34. Driver tab and click Reinstall driver Nikon COOLSCAN IV ED Properties KE General Driver Gp Nikon COOLSCAN IV ED Device type Other devices Manufacturer None specified Hardware version Not available di Al NVDS1009 r Device status The drivers for this device are not installed Code 28 To reinstall the drivers for this device click Reinstall Driver Reinstall Driver m Device usage Click Next When the Update Device Driver Wizard is displayed m This wizard searches for updated drivers for click Next Nikon LS 40 ED 4 device driver is a software program that makes a hardware device work Upgrading to a newer version of a device driver may improve the performance of your hardware device or add functionality 4 Select the search option Select the search option and click Next Display a list of all the drivers in a specific location so you can select the driver you want lt Back E Cancel 81 a D Insert the Nikon Scan 3 CD The dialog shown at right will be displayed Hold ing down the shift key to prevent the Welcome pro Windows will search for updated drivers in its driver database on your hard drive and in any of the following selected locations Click Next to start the search gram from starting automatically insert the Nikon Fee wil Se Scan 3 CD into the CD ROM drive then select aS Pies Specify a location and click Browse a TE The Welcome Win
35. E 1394 Host Controller appears in the Device Manager under IEEE 1394 Bus host controllers ox r F Open Explore Search Manage Map Network Drive Disconnect Network Drive Create Shortcut Rename Action View I e TEWE Computer amp Disk drives Display adapters 2 DYD CD ROM drives Sy Floppy disk controllers E E H F F amp Floppy disk drives DEALA ik TAP On ST TA Mice and other pointing devices 3 Monitors S Network adapters Other devices of Ports COM amp LPT g Sound video and game controllers m System devices Universal Serial Bus controllers Windows Millennium Edition Me The first time the computer is powered on with the board in place Windows Me will automati cally install the board drivers To confirm that the drivers are installed and functioning normally 1 The dialog shown at right will be dis played Click Yes to restart your com puter 2 Click on the My Computer icon with the right mouse button and select Properties from the menu that ap pears 3 In the System Properties window click the Device Manager tab Check that NEC Firewarden OHCI Compliant IEEE 1394 Host Controller appears in the Device Manager under 1394 Bus Controller System Settings Change x Q You must restart your computer before the new
36. H 3 to scan strip film too short or too badly damaged to be used in the SA 21 IEEE 1394 Firewire interface board 1 includes user s manual 4000 ED only If you are using a Windows or old model beige Macintosh G3 desktop computer you may need to install this PCI board before you will be able to connect your scanner to your computer This board can not be used with laptop computers or computers not equipped with a PCI slot and is not required in the case of Macintosh com puters with built in Firewire ports FH 3 strip film holder for MA 20 S 1 Place strip film to be scanned in this holder before scanning it with the MA 20 S USB interface cable 1 COOLSCAN IV ED only Use this cable to connect the COOLSCAN IV ED to your computer SA 21 strip film adapter 1 This adapter can be used to scan single or mul tiple selected frames in film strips two to six frames in length The frames to be scanned can be previewed and selected using Nikon Scan 4 Open me first Open me first envelope 1 This envelope contains user registration cards and other important documents Nikon Scan 3 CD ROM 1 This CD contains driver software for your Nikon scanner Depending on the country of sale it may also include a variety of sample software SUPER COOLSCAN AED COOLSCANIW ED User s Manual User s Manual this manual 1 Reference CD 1 This CD contains a reference ma
37. If the small holes are on both sides on the film use the FH 3 film holder with the MA 20 S slide mount adapter vV Care should be taken not to injure yourself when using scissors to trim the film Film that has been repaired or that has just been developed may jam in the adapter If the film jams use the FH 3 film holder with the MA 20 S slide mount adapter 104 Using the FH 3 The FH 3 can be used in combination with the MA 20 S to scan strips of 35 mm film of one to six frames in length including film that can not be scanned in the SA 21 FH 3 MA 20 S Hold the adapter with the Nikon logo face up vy Pg For more information on 102 Film that can not be scanned in the SA 21 105 2 Unlatch the holder snaps and flip the upper holder open 3 Place a strip of film in the lower por tion of the holder aligning each frame with an aperture in the lower holder The shiny surface of the film should face up the emulsion surface should face down so that the frame numbers are not reversed Aperture Frame number 106 4 Return the upper holder to its origi nal position aligning the ends with the ends of the lower holder D Fasten the snap on the FH 3 and fit the upper and lower ends of the holder together 107 E 6 Align the frame you want to scan with either of the two apertures see page t 110 for information on scanning frames in order starting at the first frame
38. Logo testing Continue Anyway STOP Installation Click Finish Click Finish to complete installation Hardware Update Wizard Completing the Hardware Update Wizard The wizard has finished installing the software for P Nikon SUPER COOLSCAN 4000 ED Click Finish to close the wizard J Confirm device registration Confirm that the scanner has been correctly registered with the system as described in Confirming Device Registration Windows XP on 32 35 7 Windows 2000 Professional Registering the Scanner with Windows 2000 Professional 4000 ED 1 Turn the scanner on The first time the computer detects the scanner Windows will display the dialog shown at right Click Next Insert the Nikon Scan 3 CD Holding down the shift key to prevent the Welcome program from starting automati cally insert the Nikon Scan 3 CD into the CD ROM drive Select the search option and click Next Logging On Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install a device driver for a hardware device To continue click Next Found New Hardware Wizard i Install Hardware Device Drivers 4 device driver is a software program that enables a hardware device to work with an operating system This wizard will complete the installation for this device op Nikon LS 4000ED IEEE 1394 SBP2 Device device driver is a software program that makes
39. OOLSCAN IV ED 4 Select Is40xp inf Select Is40xp inf in the list of drivers and PT click Next Please select the best match for your hardware from the list below Fra Rant Y Is40xp int If ls40xp inf is not visible in the list drag ga Uon OSOAN IY E the scroll bar at the right of the list until it v Eaosion K H Unknown Nikon Corporation g infSls40 winxp ls40xp inf IS d ISP ayed Unknown Nikon Corporation g inf ls40 winmes40me inf Unknown Nikon Corporation g infXls40 win98se ls40se inf Unknown Nikon Corporation g inf ls40 win2000 Is402k inf A This driver is not digitally signed Tell me why driver signing is important Click Continue Anyway Click Continue Anyway to begin installa eg tion of the Tiles need to register the scanner The software you are installing for this hardware Nikon COOLSCAN IV ED has not passed Windows Logo testing to verify its compatibility with Windows xP Tell me why this testing is important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing Continue Anyway STOP Installation Click Finish Click Finish to complete installation AERES OEE Completing the Hardware Update Wizard The wizard has finished installing th
40. UPER COOLSCAN 4000 ED Click Finish to close the wizard Confirm that the scanner has been correctly registered with the system as described in Confirming Device Registration Windows XP on 32 31 m Confirming Device Registration Windows XP 4000 ED After registering the scanner confirm that the device is working normally as described below 1 2 4 32 Turn the scanner on Make sure that the scanner is connected and turned on Open the System Properties dialog Select Control Panel from the Start menu open Performance and Maintenance and click System Display the Device Manager The System Properties dialog will be dis played Open the Hardware tab and click Device Manager Confirm that the scanner is listed un der Imaging devices If Imaging devices appears in the De vice Manager click the to Its left to view the imaging devices currently regis tered with Windows Confirm that your scanner Is listed If the Scanner Is Not Listed If your scanner is not listed under Imag ing devices proceed to Updating the Device Driver Windows XP EJ 34 System Properties System Restore Autona Remote General Computer Name Advanced Add Hardware Wizard Z The Add Hardware Wizard helps you install hardware Add Hardware Wizard Device Manager The Device Manager lists all the hardware devices installed on your computer Use the Device Manager to change the p
41. a ceataccmnnscesecne teas 122 AUTOFOCUS sirenaren sedtned cand sen secu sedetedente 122 C EPOD cice en eto te ents one ANAE 92 D Device registration 4000 ED 20 cece eeeceeeceeeeeeeeeeeneees 30 36 44 50 COOLSCAN IV ED naan 57 63 70 76 Dust and lint naasian 6 7 103 127 142 E Ejecting film aananaaanenennnnnennnennnnae 98 115 122 F a EE E A E aeeaiee 84 CUN eea E a setae ueceevesseeseeaieest 102 emulsion surface of cc ceeeeeeeeeeeees 85 112 JAS ai tse pecs rremas gsdeeamianes 113 IPE arasi eee 87 122 Film holder FH 3 ee A 4 105 147 apertures IN sirasini 108 PR eurem s ucnieesteoeedeeeeeeweae 143 148 l IEEE 1394 board 00 ee eeccceccecceeeeeeeeeeeeeeneeeaes 4 9 IEEE 1394 interface cable asaina 4 26 ISIS CUIONN seedscehoosancsctonssesnntdeteencamagmionecadeanens 137 Install See Nikon Scan installing M Macintosh siesccicccctieecnecececcceccadctacecesseceodis 21 118 Maintenance ACCESSOMICS oo cccecceeceeceeceuceeeeeeeeueceeeeeeeeeneees 139 SCANNET carvan cdonisanccdunsiapananadaintviasonvodndaaasen 137 N Nikon Scan sanictcoradicetecsnteccecsecestecnaticcteuen 16 117 stali ei 11 16 21 Nikon Scan 3 Reference Manual 5 118 Nomenclature cccceeeeeeeeeeeeeeeeeees 3 120 121 150 P Perforations c cccceccseceeeeeeeeeeeeees 102 103 104 Power cable 2 ccccceeceeeceeeeeeeeeeeeeeneeeneeeeees 4 25 COMME CUING desees dae irisean 3 25 Power switc
42. aN VVINCLOW aa ee ceee cee entree secon 120 117 Viewing the Nikon Scan 3 Reference Manual Your Nikon scanner is controlled using Nikon Scan driver software which must be installed before you can use your scanner The operating manual for Nikon Scan may be found on the reference CD provided with your scanner where it is stored in Adobe Acrobat Portable Docu ment Format pdf To view the manual you will require Adobe Acrobat Reader 4 0 or later English German Spanish French Italian Japanese and Dutch versions of Adobe Acrobat Reader 4 0 can be found on the reference CD To install Acrobat Reader follow the instructions below 1 Insert the software manual CD in the CD ROM drive Macintosh users can proceed to Step 3 2 Windows only Double click the My Computer icon In the My Computer window double click the CD ROM drive labeled Nikon 3 The Nikon window will open on the desktop Double click the folder for the lan guage of your choice D E Y Nikon E A 9 items zero K available File Edit View Favorites Tools Help File and Folder Tasks English gt Publish this Folder to the Web Nederlands Italiano POF pA Japanese INDEX pdf NIKON 0 CD Drive Windows Macintosh 4 Double click the setup Windows or installer Macintosh icon setup exe PackageForTheweb Stub InstallShield Software Corpora Reader Installer Windows Macintosh To ge
43. allation was successful You have installed software which suggests you restart your computer If you are finished click Restart or click Quit to leave the Installer Ifyou wish to perform additional installations click Continue The software was successfully installed Connecting the Scanner The first time the scanner is connected to a Windows computer the Device Manager will install the device drivers needed to register the scanner with the system For information on regis tering the scanner see Registering the 4000 ED with Windows EJ 30 56 or Registering the COOLSCAN IV ED with Windows RJ 57 82 Connecting the Power Cable A power cable is provided with your scanner Before connecting the cable making sure the scanner is off After connecting the cable to the AC connector on the rear of the scanner plug it into a general purpose household power outlet AC 100 240 V 50 60 Hz If a separate ground wire is provided be sure to attach the ground wire to the earth connector Power switch off Power switch on Illustration shows 4000 ED 25 EE Connecting the Interface Cable 4000 ED After confirming that the scanner is off connect one end of the supplied 6 pin 6 pin IEEE 1394 cable to the scanner the other to the computer Connect the cable as shown Attempting to insert the connector in another orientation could not only damage the connector but also damage the sca
44. ance Caring for Your Scanner Storing the Scanner When not using the scanner turn It off remove any adapters from the adapter slot and slide the cover closed as shown below Sliding cover If you will not be using the scanner for an extended period turn off and unplug the scanner Store the scanner where e the temperature is between minus twenty and plus sixty degrees Centigrade 4 F 140 F e the humidity is between twenty and ninety percent no condensation Servicing Your Scanner Your scanner is a precision machine We recommend that you take your scanner and adapters to an authorized Nikon service representative once every one to two years for inspection and once every three to five years for servicing a fee is charged for these services Frequent inspection and servicing are particu larly recommended in the case of scanners used in commercial applications v When not using the scanner remove any adapters and close the cover to prevent dust from accumulating inside the scanner Accumulation of dust on the optical mirrors in the vicinity of the adapter slot could result in scanning errors Should an error occur remove dust by sending air into the adapter slot with a blower Do not insert your fingers into the adapter slot 137 i Cleaning the Scanner Before cleaning the scanner turn it off and unplug the power cord The front of the scanner is made of plastic and consequently cannot be cleaned with vol
45. ance and Maintenance icon In the Performance oa and Maintenance window click the ie ee ea a ain S yste m i C O n E x See basic information about your computer 2 Startup and shutdown Adjust visual effects Free up space on your hard disk Back up your data 2 T h e Syste m d i a O g wi b e d iS p a ye d Rearrange items on your hard disk to make programs run faster Select the Hardware tab and click Device or pick a Control Panel icon Ma nager Er Administrative Tools A Power Options Scheduled Tasks YE System Confirm that a listing for NEC Z Device Manager Firewarden OHCI Compliant IEEE 1394 arre Host Controller appears in the Device 5 oy sines amp Floppy disk controllers M a n a g e r J Floppy disk drives Monitors E Network adapters Ports COM amp LPT SBR Processors Sound video and game controllers Y System devices Universal Serial Bus controllers 11 7 Windows 2000 Professional The first time the computer is powered on with the board in place Windows will automatically install the necessary drivers To contirm that the drivers have been installed and are functioning normally 1 12 Click on the My Computer icon with the right mouse button and select Properties from the menu that ap pears In the System Properties window open the Hardware tab and click the Device Manager button Check that NEC Firewarden OHCI Compliant IEE
46. annel c0ccecceeeee eee 2 Getto KNOW YoUr scanne oee e e eee 3 Msta liin NIKOM C a cae see ere 16 Conneding the scannet ae crews ne aa 25 Turm ne Scanner Ima a tee 28 E Before Using Your Scanner Connecting the Scanner e Connect the scanner directly to the computer as described in Connecting the Scan ner EJ 25 The scanner may not function as expected when connected to an IEEE 1394 hub The scanner may not function as expected used with other IEEE 1394 devices Should you notice a problem with the scanner when used with other IEEE 1394 devices disconnect the other devices and use the scanner alone e Only one scanner can be connected to the computer at a time Using the Scanner with a Windows Computer Before you will be able to use your scanner with a Windows computer you must register the scanner with the system Before registering the scanner disconnect all other peripherals from the computer and connect only the scanner Get to Know Your Scanner Your Scanner 4000 ED Status LED This LED blinks slowly roughly twice every three seconds when the scanner is in op eration Do not turn the scanner off remove or insert adapters or eject or insert film until the LED has stopped blinking and is glowing steadily If the LED flashes rapidly about five times a second a communications error has occurred or there is a problem with the scan ner Turn the scanner off wait for at least
47. ard Welcome to the Found New Hardware Wizard This wizard helps you install software for LS 40 ED If your hardware came with an installation CD lt 6 or floppy disk insert it now What do you want the wizard to do Hardware Installation Click Next to continue The software you are installing for this hardware Nikon GOOLSCAN IV ED has not passed Windows Logo testing to verify its compatibility with Windows xP Tell me why this testing is important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing Log on as the Computer Administrator when registering the scanner The Welcome Window If the Welcome program starts automatically when you Insert the Nikon Scan CD click Exit to close the Welcome window 1 Welcome Continue Anyway STOP Installation Copyright 1998 2001 Nikon Inc and Nikon Corporation GR Viikon Scan 3 e eade hitp www Nikon Asia com hitp www Niken Euro com itp Awww Nikon USA com di Al N O O N re gt m Click Finish Click Finish to complete installation neare Nori Completing the Found New Hardware Wizard The wizard has finished installing the software for Nikon GOOLSGAN IM ED J Click Finis
48. at you should read before using your Nikon scanner This icon marks tips additional information you may find helpful when using your Nikon scanner This icon indicates that more information is available elsewhere in this manual or in other documentation This symbol indicates that the cross reference marked with the AN icon is to the 4000 ED COOLSCAN IV ED User s Manual this manual This symbol indicates that the cross reference marked with the M icon is to the Nikon Scan 3 Software manual on CD Illustrations The majority of illustrations in this manual are taken from Windows XP Home Edition or Windows XP Professional hereafter Windows XP Illustrations from Mac OS are used together with Windows illus trations where operations in the two operating systems differ Life Long Learning As part of Nikon s Life Long Learning commitment to ongoing product support and education continu ally updated information is available on line at www nikon euro com Visit this site to keep up to date with the latest product information tips answers to frequently asked questions FAQs and general advice on digital imaging and photography viii Setup This chapter describes how to set up the scanner how to install Nikon Scan and how to connect the scanner It also describes how to care for your scanner when it is not in use and how to treat film to ensure the best results when you make a scan Before Using Your SC
49. atile cleaners such as alcohol or paint thinner Use a blower to blow off dust or wipe the surface with a dry cloth Remove dirt trom the metal rear panel of the scanner using a soft dry cloth If this is not sufficient to remove all dirt clean with a cloth that has been slightly dampened with a neutral detergent or liquid soap Transporting the Scanner Follow the steps below to prepare the scanner for transport Remove any adapters and close the sliding cover Turn the scanner on Wait for the status LED on the front of the scanner to stop blinking Turn the scanner off Disconnect the power and interface cables O UI WN After checking that no film remains in the adapters package the scanner and adapters in the original packing materials m Nikon scanners are certified for use in the country or region of sale Transportation and use outside the country or region of sale are at the user s own risk and responsibility Where the original packing materials are not available package the scanner carefully in materi als at least as shock resistant as the originals 138 Caring for Adapters Storing the SA 21 Strip Film Adapter Remove the SA 21 strip film adapter from the scanner when not in use If you will not be using the adapter for an extended period store it where e the temperature is between minus twenty and plus sixty degrees Centigrade 4 F 140 F e the humidity is betwee
50. atures specific to your scanner 127 7 The Scan Progress Window Progress Window No scanning tens Queue Log This window shows the progress of preview and scan operations The current task can be cancelled by clicking the Stop button Tasks that have yet to be performed are listed in the Queue tab and can be cancelled by selecting the task and clicking the 1 button When performing multiple batch scans the tasks completed are listed in the Log tab Progress Window AcQuInAg scan w Performing Scar Queue Log The progress of preview and scan operations is indicated as shown above 128 Reference This chapter includes troubleshooting instructions maintenance tips a list of optional accessories available for your scanner prod uct specifications and an index Troubleshooting saree ce eet cere ene 130 When Film Jams in the SA 21 133 Maintenance a o 137 Optional Accessories cccsseseeeeeeeees 143 Specifications sac era a a a 144 Er ae E E E E E E 150 129 Troubleshooting Should you encounter problems with your scanner refer to the following section and the trouble shooting section in the Nikon Scan 3 Reference Manual before consulting your retailer or Nikon representative y e The power cable is not properly connected aa After confirming that the scanner is off reconnect the power 25 cable The scanner does not turn The scan
51. cking in turn on each oiu biii of the following folders windows sys Te cine tem32 and drivers ntmap sys will E system32 be selected in the list of files Click OK mee and confirm that the scanner has been correctly registered with the system as described in Confirming Device Registra tion Windows 98 SE RJ 53 This com pletes device registration 3b Insert the Nikon Scan 3 CD The dialog shown at right will be displayed MEHE Holding down the shift key to prevent the Welcome program from starting automati cally insert the Nikon Scan 3 CD into the CD ROM drive then select the search op tion and click Next The Welcome Window If the Welcome program starts automati cally when you insert the Nikon Scan CD click Exit to close the Welcome window What do you want Windows to do Display a list of all the drivers in a specific location so you can select the driver you want aq 0007 lt Back _ ne Cancel 4 Select Specify a location Select Specify a location and click M M Browse Windows will search for updated drivers in its driver database on your hard drive and in any of the following selected locations Click Next to start the search Tl Floppy disk drives M CD ROM drive T Microsoft Windows Update IV Specify a location Y Browse lt Back EES Cancel The Welcome Window If the Welcome program starts automatically when mzez
52. d by law from being copied or reproduced Do not copy or reproduce paper money coins securities government bonds or local gov ernment bonds even if such copies or reproductions are stamped Sample The copying or reproduction of paper money coins or securities which are circulated in a foreign country is prohibited Unless the prior permission of the government has been obtained the copying or reproduc tion of unused postage stamps or post cards issued by the government is prohibited The copying or reproduction of stamps issued by the government and of certified docu ments stipulated by law is prohibited e Cautions on certain copies and reproductions The government has issued cautions on copies or reproductions of securities issued by pri vate companies shares bills checks gift certificates etc commuter passes or coupon tickets except when a minimum of necessary copies are to be provided for business use by a company Also do not copy or reproduce passports issued by the government licenses issued by public agencies and private groups ID cards and tickets such as passes and meal coupons e Comply with copyright notices The copying or reproduction of copyrighted creative works such as books music paintings woodcut prints maps drawings movies and photographs is prohibited except when it is done for personal use at home or for similar restricted and non commercial use Trademark Information Apple the Appl
53. d wheel m Work with the adapter and scanner on a table or other flat stable surface The adapter or scanner could be damaged should either fall to the floor 141 E Remove dust and dirt from the interior of the adapter with a blower Clean the feed mecha nism thoroughly changing the angle of the blower to reach all parts of the mechanism Be sure that dirt and dust do not remain on the adapter s three sensors Caring for the FH 3 Film Holder When cleaning the holder do not use volatile cleaners such as alcohol or paint thinner Use a blower to remove dust Clean dirt from the holder with a soft dry cloth or dampen the cloth with a neutral detergent to remove particularly stubborn stains drying once cleaning is complete Caring for the MA 20 S Slide Mount Adapter When cleaning the adapter do not use volatile cleaners such as alcohol or paint thinner Use a blower to remove dust Clean dirt from the adapter with a soft dry cloth or dampen the cloth with a neutral detergent to remove particularly stubborn stains drying once cleaning is complete 142 Optional Accessories Options Available for the 4000 ED and COOLSCAN IV ED IA 20 S Adapter for APS IX240 Film The IA 20 S is used to scan APS IX240 film FH G1 Medical Slide Holder The FH G1 is used in combination with the MA 20 S to scan prepared microscope slides containing samples of pathological tissue lwi
54. dow If the Welcome program starts automatically when you insert the Nikon Scan CD click Exit to close the Welcome window 6 Select the Ls40 folder The Browse for Folder dialog will be displayed Se z aa eena lect the Ls40 folder under Nkscan gt INF and click OK to return to the dialog shown in step 5 Confirm that the path INF Ls40 appears after caer the drive letter of the CD ROM drive and click Next C Nkscan H H al Printers Cancel Begin installation of the device drivers A dialog will be displayed stating that Windows has vice Diver Wa found the drivers for the device Click Next Windows diver fle search far the device Nikon LS 40 ED COOLSCAN IV ED J Windows is now ready to install the best driver for this device Click Back to select a different driver or click Next to continue Location of driver Click Finish Click Finish to complete installation izar s Nikon COOLSCAN IV ED Windows has finished installing the driver you selected for your hardware device 9 Confirm device registration Confirm that the scanner has been correctly registered with the system as described in Confirming Device Registration Windows 98 SE on 79 80 82 Scanning 35 mm Slides This chapter describes how to scan 35 mm slides using the MA 20 S slide mount adapter provided with your scanner Step 1 Ready the Slide
55. driver information IMF file for this device Browse for Folder He D He E He IF El Nkecan G A Firmware PT lg Micrasatt H Nkecan a H ae Printers El Cancel Add New Hardware Wizard Windows will search for new drivers in its driver database on your hard drive and in any of the following selected locations Click Next to start the search I Floppy disk drives T CD ROM drive I Microsoft Windows Update IV Specify a location G INFALS40 x 77 di Al NVIS100 E 6 Begin installation of the device drivers Click Next J Click Finish Click Finish to complete installation COOLSCAN IV ED Q Confirm device registration Add New Hardware Wizard Windows driver file search for the device Nikon LS 40 ED Windows is now ready to install the best driver for this device Click Back to select a different driver or click Next to continue Location of driver te G MINFALS408LS40 INF Add New Hardware Wizard 2 Nikon LS 40 ED Windows has finished installing the software that your new hardware device requires Cancel Confirm that the scanner has been correctly registered with the system as described in Confirming Device Registration Windows 98 SE on 79 78 Confirming Device Registration Windows 98 SE After registering the scanner contirm that the device is working normally as described below 1 Turn the scanner on Make sur
56. drivers in a specific location so you can select the driver you want lt Back f Nee f canca D Insert the Nikon Scan 3 CD The dialog shown at right will be displayed MENIER Holding down the shift key to prevent the Welcome program from starting automati cally insert the Nikon Scan 3 CD into the CD ROM drive then select Specify a loca tion and click Browse The Welcome Window If the Welcome program starts automatically when you insert the Nikon Scan CD click Exit to close the Welcome window windows will search for updated drivers in its driver database on your hard drive and in any of the following selected locations Click Next to start the search I Floppy disk drives M CD ROM drive T Microsoft Windows Update I Specify a location a ok lt Back Cancel 55 aq 0007 a 6 Select the Win98SE folder The Browse for Folder dialog will be dis EEZ HE played select the a folder Am Select the folder that contains driver information INF file for der Nkscan gt INF gt Ls4000 and click this device OK to return to the dialog shown in step 5 Confirm that the path INF LS4000 Win98SE appears after the drive letter of the CD ROM drive and click Next oe F peg Mkacan G ee Firmware EMS INF BC Ls4000 Bev Microsoft fea Nkscan gt Cancel 7 Begin installation of the device drivers A dialog will be displayed stating tha
57. dy equipped with a built in IEEE 1394 interface port or a suitable expansion board or card you can install the IEEE 1394 Firewire interface board provided with your scanner Detailed instructions may be found in the manual included with the interface board Do I Need to Install the IEEE 1394 Firewire Interface Board You will not need to install the IEEE 1394 Firewire interface board provided with your scanner if e Your computer is equipped with a built in IEEE 1394 Firewire port Macintosh users should note that old model beige G3 computers are not equipped with a built in Firewire port e Your computer is equipped with an IEEE 1394 Firewire expansion board or card approved for use with the 4000 ED The IEEE 1394 Firewire interface board included with your scanner can not be used in laptop computers or in low profile PCI slots In these cases you will need to install one of the interface boards or cards recommended by Nikon For more information see the following web site http www nikon image com en ei_cs index htm Installing the Interface Board There are two steps to installing the interface board 1 Insert the interface board in one of your computer s free PCI slots EJ 10 2 Install the drivers for the interface board Windows only 11 15 In Windows XP Windows 2000 Professional and Windows Me the necessary drivers will be installed automatically after you install the interface board If you are using a comput
58. e SA 21 or SA 30 24 0 x 36 0 mm when scanning 35 mm film in the FH 3 S 25 1 x 36 8 mm when scanning 35 mm film in the MA 20 S or SF 200 S 16 1 x 26 9 mm when scanning APS IX240 film 3529 x 5379 pixels when scanning 35 mm film in the SF 200 S 3546 x 5782 pixels when scanning 35 mm film in the MA 20 S 3654 x 5646 pixels when scanning 35 mm film in the SA 21 or SA 30 3762 x 5646 pixels when scanning 35 mm film in the FH 3 S 2525 x 4219 pixels when scanning APS IX240 film Fixed tilm movable plane single pass optical scanning system Red green and blue RGB LEDs 3964 pixel linear CCD image sensor Performed by RGB color LEDs Maximum 4000 pixels per inch Analog to digital A D conversion 14 bits per color RGB Output Full color 8 or 16 bits per color RGB Focus Autofocus Manual Scanning time Duration of Scanning on processes Preview Computer FMV715GTX6 Pentium 4 1 5GHz RAM 1GB OS Windows 2000 Software Nikon Scan 3 1 Board IEEE 1394 I F Board included in the 4000 ED package Adapter MA 20 S Slide Mount Adapter Input Resolution 4000dpi Scan Bit Depth 14bit CMS On Film Positive Interface IEEE 1394 Power supply AC 100 240 V 50 60 Hz Maximum power consumption while scanning Not exceeding 20W Power consumption at standby Not exceeding 10W Operating environment e Temperature 10 35 C 50 95 F e Humidity 20 60 Dimensions 93 x
59. e device To continue click Next E Cancel 4 Select the search option Select the search option and click Next Install Hardware Device Drivers ae 4 device driver is a software program that enables a hardware device to work with cy an operating system This wizard upgrades drivers for the following hardware device a Nikon LS 4000ED IEEE 1394 SBP2 Device 5 Upgrading to a newer version of a device driver may add functionality to or improve the performance of this device What do you want the wizard to do Search for a suitable driver for my device recommended Display alist of the known drivers for this device so that can choose a specific driver lt Back E Cancel D Insert the Nikon Scan 3 CD Holding down the shift key to prevent the Welcome program from starting automati e ark NAS Sch SCARE DJ cally insert the Nikon Scan 3 CD into the g Search for driver files for the following hardware device m CD ROM drive m a Nikon LS 4000ED IEEE 1394 SBP2 Device io The Welcome Window If the Welcome program starts automati cally when you insert the Nikon Scan CD ei Tooke click Exit to close the Welcome window T Floppy disk chives CD ROM drives IV Specify a location F Microsoft Windows U pdate The wizard searches for suitable drivers in its driver database on your computer and in any of the following optional search locations that you specify To start th
60. e logo Macintosh Mac OS Power Macintosh and PowerBook are registered trademarks of Apple Computer Inc Finder and Power Mac are trademarks of Apple Computer Inc IBM and IBM PC AT are registered trademarks of International Business Machines Corporation PowerPC is a trademark of International Business Ma chines Corporation used under license Microsoft is a registered trademark and Windows MS Windows and Win dows NT trademarks of Microsoft Corporation Internet Explorer is a product of Microsoft Corporation Pentium is a trademark of Intel Corporation Internet is a trademark of Digital Equipment Corporation Netscape and Netscape Navigator are registered trademarks of Netscape Communications Corporation Adobe and Acrobat are registered trademarks and Photoshop a trademark of Adobe Systems Inc Applied Science Fiction Digital ICE cubed Digital ICE Digital ICE Digital ROC and Digital GEM are trademarks of Applied Science Fiction Inc Digital ICE cubed and Digital ICE are used throughout the documentation provided with this product as generic terms to describe Digital ICE Digital ROC and Digital GEM which are technologies of Applied Science Fiction Inc Radius ColorMatch and PressView are registered trademarks of miro displays inc All other trade names mentioned in this manual or the other documentation provided with your Nikon product are trademarks or registered trademarks of their respective holders Table of C
61. e needed to view the manual Adobe Acrobat Reader 4 0 Instructions for installing Adobe Acrobat Reader 4 0 are given in Step 6 of Setup in the User s Manual For Your Safety To prevent damage to your scanner or injury to yourself or to others read the following satety precautions in their entirety before using this equipment Keep these safety instructions where all those who use the product will read them The consequences that could result from failure to observe the precautions listed in this section are indicated by the following symbols This icon marks warnings information that should be read before using the scanner to prevent possible serious injury or death This icon marks cautions information that you should read before using the scanner to v prevent damage to the equipment or injury to yourself or to others WARNINGS Do not disassemble or modify e The interior of the scanner contains areas of high voltage Removing the scanner s cover could result in fire or electric shock Contact your dealer or Nikon service office for inspection or repair e Do not modify Modification could result in fire or electric shock Do not touch exposed parts Should the product break open as the result of a fall or other accident do not touch the exposed parts Failure to observe this precaution could result in injury or electric shock Unplug the power cable and take the product to a Nikon authorized service center for inspec
62. e scanner be sure to eject the film by clicking the eject button in Nikon Scan circled in the illustration above Attempting to remove the adapter without ejecting the film can result in the adapter becoming separated from the connectors at the rear of the adapter slot interfering with scanning If you have attempted to remove the adapter before ejecting film push the adapter back into the slot slightly to ensure that the connection is not interrupted Do not attempt to remove the adapter by force as this could damage both the adapter and scanner To eject film when the computer is off or Nikon Scan is not running turn the scanner off and then on again The film will be ejected automatically releasing the adapter lock mechanism Wait for the status LED to stop flashing and then remove the adapter and close the sliding cover 115 E 116 Close the sliding cover Slide the cover closed Exit Nikon Scan If you are using Nikon Scan as a stand alone application choose Exit Windows or Quit Macintosh from the File menu to exit Nikon Scan If you are using Nikon Scan to scan images directly into another application simply close the scan window by clicking the close box Turn the scanner off COOLSCAN IV ED Wait for the status LED to stop blinking then press the power button to turn the scan ner off 4000 ED If you are using a Macintosh or a computer running Windows XP or Windows 2000 Professional wait for the sta
63. e search click Next If you are searching on a floppy disk or CD ROM drive insert the floppy disk or CD before clicking Next lt Back L_New gt Cancel 6 Reinstall the drivers Reinstall the drivers as described in steps 3 8 of Registering the Scanner with Windows 2000 Professional J 37 38 J Click Finish When the wizard displays a message stat CEINE ing that it has found the drivers for your scanner click Finish to complete installa tion If prompted to restart the computer click Yes Completing the Upgrade Device Driver Wizard 2 Nikon SUPER COOLSCAN 4000 ED Pra Windows has finished installing the software for this device To close this wizard click Finish i fee 8 Confirm device registration Confirm that the scanner has been correctly registered with the system as described in Confirming Device Registration Windows 2000 Professional on 40 41 43 7 Windows Millennium Edition Me Registering the Scanner with Windows Me 4000 ED Turn the scanner on The first time the computer detects the scanner Windows will display the dialog shown at right After confirming that the Nikon Scan CD Is inserted in the CD ROM drive select the search option and click Next Inserting the Nikon Scan CD If the Nikon Scan CD is not in the CD ROM drive insert the disk while holding down the shift key to prevent the Welcome pro gram from starting automatically 2 Select LS
64. e software for a Nikon COOLSCAN IV ED Click Finish to close the wizard J Confirm device registration Confirm that the scanner has been correctly registered with the system as described in Confirming Device Registration Windows XP J 59 60 62 Windows 2000 Professional Registering the Scanner with Windows 2000 Professional 1 Turn the scanner on The first time the computer detects the EENIA scanner Windows will display the dialog shown at right Click Next Welcome to the Found New Hardware Wizard This wizard helps you install a device driver for a hardware device To continue click Next Cancel 2 Insert the Nikon Scan 3 CD Holding down the shift key to prevent the A A e prog oe from eraruing automati AE A PENEN that enables a hardware device to work with D Z9 cally insert the Nikon Scan 3 CD into the _ sainsstn Se CD ROM drive Select the search option This wizard will complete the installation for this device and click Next Oy eee 4 device driver is a software program that makes a hardware device work Windows needs driver files for your new device To locate driver files and complete the installation click Next What do you want the wizard to do Search for a suitable driver for my device recommended Display a list of the known drivers for this device so that can choose a specific driver lt Back Lre Cancel Logging On Log on as t
65. e that the scanner is connected and turned on 2 Open the System Properties dialog From the Start menu select Settings gt Control Panel and double click the System ICON 3 Display the Device Manager The System Properties dialog will be dis EOE zjx played Open the Device Manager tab General Device Manager Hardware Profiles Performance System Microsoft Windows 98 Second Edition 4 10 2222 A Registered to 50578 335 0622301 02389 Computer Genuinelntel x86 Family 6 Model 8 Stepping 3 255 0MB RAM di Al NVDS1009 Confirm that the scanner is listed under Imaging Device If Imaging Device appears in the Device QEZ zjx Manager click the to its left to view General Device Manager Hardware Profiles Pertormance the imaging devices currently registered ioe iy i View devices by type View devices by connection with Windows Confirm that your scan nec ner is listed H S 1394 Bus Controller 43 CDROM amp Disk drives S Display adapters gee disk controllers If the Scanner Is Not Listed If your scanner is not listed under Imag ing Device proceed to Updating the 2 E Te e Device Driver Windows 98 SE on 81 oo Nikon COOLSCAN IV ED 4 2 iden Monitors H Mouse 3 Network adapters a Other devices B PC ig socket gt abe ONLI O IMT Properties Refresh Remove Print E a 4 4 Cancel 79
66. eaning the equipment Save where indicated otherwise do not put your fingers into the equipment Failure to observe this precaution could result in injury Unplug the equipment when not in use For your safety turn off and unplug the scanner when you do not intend to use it for an extended period Failure to observe this precaution could result in fire Observe appropriate precautions when handling the power cable e Donot place the power cable in the vicinity of a stove or heater as this could melt the insulation resulting in fire or electric shock e Unplug the cable by the plug never by pulling on the cord itself Failure to observe this precaution could damage the cord resulting in fire or electric shock e Do not plug the power cable into an extension cord or multi outlet adapter as this could cause fire or malfunction Ground the equipment e The outlet into which the power cable is plugged must be grounded Failure to ground the power supply could result in electric shock e Do not ground the outlet to a gas or water pipe or a dedicated telephone system earth connector Failure to observe this precaution could result in fire or electric shock iii 7 Notices e No part of the manuals included with this product may be reproduced transmitted tran scribed stored in a retrieval system or translated into any language in any form by any means without Nikon s prior written permission e Nikon reserves the right to change t
67. ect LS4000ME INF in the list of drivers and click OK LS4000ME INF Several drivers with similar names may be displayed Be sure to select LS4000ME INF 6 Click Finish Click Finish to complete installation If prompted to restart the computer click Yes 7 Confirm device registration Update Device Driver Wizard Windows was unable to locate an updated driver for this device but did find other drivers that should work with this device You are already using the best driver for this device Install one of the other drivers View List lt Back E Cancel Select Other Driver x Windows has found more than one driver that may work for your hardware Please select the driver that matches your language and device Nikon G m PER at ore CAN ei ED 5 5 2001 Update Device Driver Wizard Nikon SUPER COOLSCAN 4000 ED Windows has finished installing the driver you selected for your hardware device i Cancel Confirm that the scanner has been correctly registered with the system as described in Confirming Device Registration Windows Me on 46 47 49 di 000 7 Windows 98 Second Edition SE 4000 ED Registering the Scanner with Windows 98 SE Before beginning device registration make sure that you have completed the IEEE 1394 up date described in Updating the IEEE 1394 Drivers Windows 98 SE only on 17 1 Turn the computer on Make sure that t
68. ede cctonceeancndvnoseissinsstectetsuc awe o erna Eaa e NEE ERO na N aE r eaae 105 LIS IG NG SA a E E E E A 111 NIKOM S C aa A AAEE AE 117 Viewing the Nikon Scan 3 Software Manual s nnnnssnnnnrsnnnrreeeerenrrennnnnnnnsnnnnnnnnne 118 The Scan WINAOW a sistecccc espns seit so czenceceaedeoendee csessebeteeneco2 510ieecsaicaneecenscietseedeacoareseas 120 THE Parts OF TNE Scan WINDOW sviswsicca ne ciscenssanscean wnsiysalcbnwbdniesiawsdenmuiiews EAE EERTE rRNS 120 The OOF CG isere E sO E E tian dusndavus cutie aa niini 122 The Information Panel a niescasniceiedandoansnaanniasdhsantmsnnsmsnopiiandoduapebninarvisantaswatnsabye latumnntenasieias 124 The Preview BUTI OM ssscaoiriini aE ASEA A Ra a EEEa 125 TE e E ON e O E E 125 Ine TAINAN Drawer TaD reisiin enra Eis Ra i E nh aa k ne aiana 125 Ine Processea Natural TADS cru n css evan steeta an sndpndaainndtvaniainuea Anand eduvsentinsis lt mansdonmcenutereuabanees 125 THE TT uoaa EE aE AE AEN AA EE A AEE ees decked AE EEEE 126 The Scan Progress WINdOW srsisrssresseecorirsrniertsis meidie so er EEEE OSERE ERAO EN AE ENEE 128 BRT oars ewes a aca pew cock pte erates eects pees aces 129 Troubles hoo UNT gcontcicenctisadicsmantesoatacoccataiiniseaviaieascaartannitacnitedsiaeesanvesaeeacetecdaraidannetadnieee 130 When Film Jams in the SA 21 ccccccccccccsesceeeceseeeeceaeeeeseueeeecaeseeeseeaeeeesseaeeeeseageeeeeses 133 Pthe Alm Jams During Loading ccvesieeosesouicticcdtwincssncncdecsauelsnebinsesnns
69. ee Remove the tape or trim the ends of the film with scissors After removing tape wipe off all traces of adhesive with a soft dry cloth being careful not to There is tape on the ends of the film damage the film Trim the end of film straight across being careful not to cut across the perforations Film is cut on an angle or torn Trim the film straight across being careful not to cut across the remaining perforations If the film can not be trimmed without cutting across the im age in the frame trim only the outer edge from the The final perforation has been cut or torn perforation as shown above at left v Before scanning remove dirt and dust from the film and perforations with a blower and wipe off fingerprints with a dry soft cloth being careful not to scratch the film 103 m See page 105 for information on using the FH 3 A A Trim the folded portion from the film cutting the film straight across and being careful not to cut across the perforations The end of the film is folded Moons Trim the end of film straight across being careful Unis ete en iie li Is teera not to cut across the perforations lt There are small holes in between the perforations If the small holes are only on one side of the film insert the film as shown above
70. er running Windows 98 SE you must update the IEEE 1394 driver as instructed on page 17 of this manual before installing the interface board 7 Installing the Interface Board 4000 ED Only Installing the IEEE 1394 Firewire Interface Board in a PCI Slot After turning the computer off and disconnecting all cables insert the interface board in one of the computer s PCI slots as shown below For information on the location of the PCI slots and on installing PCI boards see the documentation provided with your computer If you will be using the interface board with devices that require power to be sup plied by the computer you will need to connect the board to the computer s power supply You will not need to con nect the power supply if you will only be using the 4000 ED which receives power from an external source V4 WARNING Observe caution when installing the interface board Use of excessive force could damage the computer or interface board 10 Installing the Device Drivers Windows Only After installing the interface board close the computer s case and reconnect all cables Windows XP Home Edition Windows XP Professional The first time the computer is powered on with the board in place Windows will automatically install the necessary drivers To confirm that the drivers have been installed and are functioning normally Select Control Panel from the Start menu and click the Perform
71. ering the scanner confirm that the device is working normally as described below 1 Turn the scanner on Make sure that the scanner is connected and turned on 2 Open the System Properties dialog From the Start menu select Settings gt Control Panel and double click the System ICON 3 Display the Device Manager The System Properties dialog will be dis 2j x played Open the Device Manager tab Bait Device Manager Harare E AE System Microsoft Windows Me 4 90 3000 Registered to 92782 335 0587771 14092 Computer Genuinelntel Intel r family 6 model 5 processor 320 0MB RAM COOLSCAN IV ED Cancel Confirm that the scanner is listed under Imaging Device If Imaging Device appears in the Device 2x Manager click the to Its left to view the imaging devices currently registered General Device Manager Hardware Profiles Performance View devices by type View devices by connection with Windows Confirm that your scan cei ner is listed H ag CDROM Disk drives If the Scanner Is Not Listed Display adapters sein disk controllers If your scanner is not listed under Imag ing Device proceed to Updating the Device Driver Windows Me EQ 74 F Monitors CA Mouse g7 Network adapters D Other devices a Ports COM amp LPT amp SCSI controllers an and game controllers mir d Properties aie Refresh Remove Pri
72. eristics of output images If helps you to select one often standard RGB color spaces Do you wish to select a color space from the name list or use the Profile Selection Wizard ence Manual for details The color space profile selected during installation can be changed at any time as detailed in the Preferences section of the Nikon Scan Software Manual Choosing the correct color space profile is very important if the scanner is to be used in a professional setting for example as part of a production workflow More information about the color management system used in Nikon Scan 3 may be found in the Nikon Scan Software Manual Clicking Use Wizard in the Color Space Wizard dialog displays the dialog shown at right Click Macintosh Choose Apple RGB recommended and click OK More information about the different profiles is available in the Nikon Scan Reference Manual Wizardl If you will be scanning images destined for the Macintosh platform press the Macintosh button If you will be scanning images destined for the Windows platform press the Windows button This is select a group of color spaces that contain the optimal gamma characteristic for the selected platform Ifyou press the Windows button you will be presented with seven color spaces that use a gamma value of 2 2 If you press the Macintosh button you will be presented with three color spaces that you use a gamma value of 1 8
73. evice NEG Firewarden OHCI Compliant IEEE 1394 Host Controller Windows is now ready to install the best driver for this device Click Back to select a different driver or click Next to continue Location of driver C WINDOWS INF 1394 INF wesen aeoo Copying Files X The file usbscan sys on Windows 98 z Second Edition CD ROM cannot be found Cancel Insert Windows 98 Second Edition CD ROM in the selected drive and click OK Skip File Details pea Browse Copy files from Io wind8_se bd Add New Hardware Wizard NEG Firewarden OHCI Compliant IEEE 1394 Host Controller Windows has finished installing the software that your new hardware device requires 15 E Installing Nikon Scan Before you can connect your scanner to your computer you will need to install Nikon Scan 3 driver software for your scanner The procedure for installing Nikon Scan 3 on Windows com puters differs from the install procedure for Macintosh computers The Nikon Scan 3 install CD includes two versions of Nikon Scan 3 version 3 1 2 for Windows and Mac OS 9 or earlier and version 3 1 3 for Mac OS X version 10 1 3 or later Thi Thi be Nikon Scan 3 Version 3 1 2 s version of Nikon Scan will be installed under Windows and Mac OS 9 or earlier Nikon Scan 3 Version 3 1 3 s version of Nikon Scan 3 is supported only under Mac OS X version 10 1 3 or late
74. ging devices currently regis tered with Windows Confirm that your scanner is listed If the Scanner Is Not Listed If your scanner is not listed under Imag ing devices proceed to Updating the Device Driver Windows 2000 Profes sional gJ 42 E Device Manana Syl i O x Action view 4 amle I m Computer H E Disk drives 2 Display adapters fd DVD CD ROM drives Floppy disk controllers H 6 Floppy disk drives IDE ATAJATAPI controllers Ej D Mice and other pointing devices Modems H Monitors 9 Network adapters El pi Other devices Ea Ports COM amp LPT ol g Sound video and game controllers H System devices Universal Serial Bus controllers D Confirm that the scanner is working properly Double click the listing for your scanner 2 xi that appears under Imaging devices General Driver The scanner Properties dialog will be dis f Nikon SUPER COOLSCAN 4000 ED played Click the General tab and con firm that This device is working properly nuna ledana appears under Device Status If another misine Mkoa message is displayed proceed to Updat Location LUN 0 ing the Device Driver Windows 2000 Pro fessional EQ 42 Device status This device is working properly you are having problems with this device click Troubleshooter to start the troubleshooter Trouble
75. h ccceecceeeeeeeeeeeees 3 28 100 116 Preview ccccceeccceccceeeeseeeeeeeees 88 120 121 125 R Rollers oo cceeceeecceeceeeceseeeeeneeeeseeeees 136 140 141 S SCAN WINGOW ceeccecceecceseceeceeeeseeeeeeeeeeseneees 120 Scanner CAG TON sesionin enera Ghacesemactanser 6 UU PEE E A T 6 Sc EEE E E E 83 101 Slides thickness of 0 85 144 146 147 Sliding COVED cccccccecssessssseeeeeeeeeeenees 3 99 116 Software manual CD e ceeeeeeeeeeeeeeees 5 118 Specifications sisicinisacncsincccnsdvancnsnmnanceedeocseenes 145 Status LED cicccceadtwacecuasvoiscccamcncadbedacbacdiwens 3 112 T Thumbnail previews 008 113 120 121 Troubleshooting rasiri 130 U USB Cable oo cceccecceecceeeeeeeeeeeeeeeeeeseeaeeneees 4 27 W Windows 98 Second Edition SE 14 17 50 76 Windows 2000 Professional 12 36 63 Windows Millennium Edition Me 13 44 70 Windows XP Home Edition Windows XP Professional ccccceeeeeess 11 30 57
76. h to close the wizard 4 Confirm device registration Confirm that the scanner has been correctly registered with the system as described in Confirming Device Registration Windows XP on 59 COOLSCAN IV ED 58 Confirming Device Registration Windows XP After registering the scanner contirm that the device is working normally as described below 1 Turn the scanner on Make sure that the scanner is connected and turned on 2 Open the System Properties dialog Select Control Panel from the Start menu open Performance and Maintenance and click System 3 Display the Device Manager The System Properties dialog will be dis ET played Open the Hardware tab and click System Restore Automatic Updates Remote Device Manager General l Computer Name Hardware Advanced Add Hardware Wizard 4 The Add Hardware Wizard helps you install hardware Add Hardware Wizard Device Manager The Device Manager lists all the hardware devices installed on your computer Use the Device Manager to change the properties of any device Hardware Profiles a Hardware profiles provide a way for you to set up and store different hardware configurations Hardware Profiles di Al NVDS1009 Confirm that the scanner is listed under Imaging devices If Imaging devices appears in the De EMMIS vice Manager click the to its leftto asea view the imaging devices currently regis 3 ue tered with Windows C
77. he Administrator when registering the scanner The Welcome Window If the Welcome program starts automatically when EXA you insert the Nikon Scan CD click Exit to close the Welcome window Be ReadMe O Ra hitp www Nikon Asia com hitip www Nikon Euro com http www Nikon USA com Select CD ROM drives Select CD ROM drives and click Next Locate Driver Files Sa Where do you want Windows to search for driver files SY Search for driver files for the following hardware device Q LS 40 ED The wizard searches for suitable drivers in its driver database on your computer and in any of the following optional search locations that you specify To start the search click Next If you are searching on a floppy disk or CD ROM drive insert the floppy disk or CD before clicking Next Optional search locations V CD ROM drives pecity a location Microsoft Windows Update lt Back Cancel 4 Begin installation of the device drivers Click Next Driver Files Search Results Na t The wizard has finished searching for driver files for your hardware device cy oy LS 40 ED Windows found a driver for this device To install the driver Windows found click Next EA h Ninf ls40 s40 inf COOLSCAN IV ED lt Back E Cancel Click Yes The dialog shown at right will be displayed Click Yes Digital Signature Not Found x The Microsoft digital signature affirms that software has been
78. he computer Click Yes to restart the computer di 00017 Confirm device registration Confirm that the scanner has been correctly registered with the system as described in Confirming Device Registration Windows Me J 46 45 m Confirming Device Registration Windows Me After registering the scanner confirm that the device is working normally as described below 1 Turn the scanner on Make sure that the scanner is connected and turned on 2 Open the System Properties dialog From the Start menu select Settings gt Control Panel and double click the System ICON 3 Display the Device Manager The System Properties dialog will be dis 21x played Open the Device Manager tab System Microsoft Windows Me 4 90 3000 Registered to 52782 335 0587771 14092 Computer Genuinelntel Intel r family 6 model 5 processor 320 0MB RAM 4000 ED Cancel Confirm that the scanner is listed under Imaging Device If Imaging Device appears in the Device 2x Manager click the to Its left to view the imaging devices currently registered General Device Manager Hardware Profiles Performance i View devices by t C View devices b ti with Windows Confirm that your scan i ea ab ee ner IS listed a 1394 Bus Controller CDROM If the Scanner Is Not Listed amp Disk drives Display adapters If your scanner is not listed under Imag Floppy disk controllers
79. he computer is on and that the scanner is off and connected to the computer via the IEEE 1394 cable 2 Turn the scanner on Turn the scanner on and wait for Windows to display a message If the Insert Disk Dialog is displayed If a message appears prompting you to EIE insert the Windows 98 Second Edition CD click OK and proceed to step 3a Do noT insert the Windows 98 Second Edition CD x Please insert the disk labeled Windows 98 Second Edition CD ROM and then click OK If the Add New Hardware Wizard is displayed If the dialog shown at right IS displayed Add New Hardware Wizard click Next and proceed to step 3b This wizard searches for new drivers for If no message is displayed If no message is displayed after 60 sec onds proceed to Updating the Device Driver Windows 98 SE J so eal Nikon LS 4000ED IEEE 1394 SBP2 Device device driver is a software program that makes a hardware device work Cancel 3a Locate ntmap sys The dialog shown at right willbe displayed PETE x Click Browse te ton wi The file ntmap sys on Windows 98 Second a Edition CD ROM cannot be found Cancel Insert Windows 98 Second Edition CD ROM _ Cancel in the selected drive and click OK Skip File Details Copy files from iii Browse 50 Navigate to C windows system32 driv ers by selecting C from the list of le name Folders drives and double cli
80. he film base and emulsion will deteriorate if exposed to high temperatures or humidity Use the scanner at the temperature and humidity given in the specifica tions see below m Sudden changes in temperature and humidity even when within the limits given in the specifications can cause condensation on the film Before using film check to be sure that no condensation is present m f condensation is present on the film leave the film out until it dries Condensation can cause damage when film is inserted in the scanner vj Before inserting film in the scanner remove dirt and dust with a blower to protect the surface of the film from scratches Dirt and dust can also interfere with the operation of the scanner causing scanning errors or malfunctions m The operating temperature and humidity for your scanner are Temperature 10 35 C 50 95 F Humidity 20 60 7 Using the 4000 ED with Other Devices When using the 4000 ED with other devices connected to the same IEEE 1394 Firewire bus m Do not turn other devices on or off or disconnect interface cables while scanning is in progress i e while the scanner status LED is blinking slowly m Connect the scanner directly to the computer The scanner may not function as expected when connected to an IEEE 1394 hub The scanner may not function as expected when operated at the same time as other IEEE 1394 devices Should a problem occur when the scanner is used wi
81. he specifications of the hardware and software de scribed in these manuals at any time and without prior notice e Nikon will not be held liable for any damages to film film rolls or APS film cartridges result ing trom the use of this product e While every effort has been made to ensure that the information in these manuals is accu rate and complete we would appreciate it were you to bring any errors or omissions to the attention of the Nikon representative in your area address provided separately Notice for customers in the U S A Federal Communications Commission FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protec tion against harmful interference in a residential installation This equipment generates uses and can radiate radio fre quency energy and if not installed and used in accordance with the instructions may cause harmful interference to ra dio communications However there is no guarantee that FOR HOME OR OFFICE USE interference will not occur in a particular installation If this Nikon COOLSCAN IV ED equipment does cause harmful interference to radio or tele vision reception which can be determined by turning the equipment off and on the user is encouraged to try to cor rect the interference by one or more of the following mea L FOR
82. hiny surface up and insert the film as shown below When the film has been inserted a short distance the adapter feed mechanism will activate and load the film the rest of the way into the adapter The status LED will blink while the scanner readies the film for scanning The status LED will stop blinking when the scanner is ready to begin scanning Scan the film as described on pages 86 98 of this manual For information on selecting the frame to be scanned see the following pages V4 Inserting Film Once the film feed mechanism has been activated do not attempt to remove the film by hand or otherwise interfere with the feed operation Failure to observe this precaution could cause an error Keep the film free from dust during insertion and scanning when the film may be partially ejected from the scanner 112 The Thumbnail Drawer F When using the SA 21 strip film adapter you can choose the frames to be scanned from the thumbnail drawer For more information on the thumbnail drawer see pages 19 to 25 of the Nikon Scan Software Manual Using the Thumbnail Drawer After selecting the film type from the media type menu and the color model from the color model menu n 87 click the thumbnail drawer tab to open the thumbnail drawer Thumbnail drawer tab Wea Cola w albrated PGE w Frames are identified by frame number To view frames as small preview images thumbnails click the Be button
83. ight will be displayed Windows 98 Second Edition 0242975 Update wh en insta lat ion Is com p ete C IC k Yes Q You must restart your computer before the new settings will take effect to restart your comp uter Do you want to restart your computer now 6 Once the computer has restarted click the My Computer icon with the right mouse ya button and select Properties from the MA Search menu that appears Map Network Drive Disconnect Network Drive Create Shortcut Rename Click the Device Manager tab in the Sys System POSALE HF tem Properties dialog and confirm that a General Device Manager Hardware Profies Perfomance listing appears for NEC Firewarden OHCI Compliant IEEE 1394 Host Controller in dicating that the update was successful 1 9 1394 Bus Controller S NEC Firewarden OHCI Compliant IEEE 1394 Host Control View devices by type View devices by connection FF Disk drives E Displey adapters Floppy disk controllers Hard disk controllers Keyboard J Modem I Monitors Mouse SNBCSUCOUE E e E pi 2 a a a eB T S jim Other devices Gd eee ch i MMA aln Properties Refresh Remove Print Cancel 17 7 Installation 1 Insert the Nikon Scan 3 CD into the CD ROM drive When the Welcome dialog is displayed click Nikon Scan 3 fiir kittp vww Nikon Asia com http www Nikon Eure com Depending on where
84. is divided into the following chapters Overview Read this chapter for information on the symbols and conventions used in this manual Setup This chapter contains all you need to know when setting up your scanner for the first time including how to install Nikon Scan and how to connect your scanner It also describes how to care for your scanner when it is not in use and how to treat film to ensure the best results when you make a scan Device Registration Before you will be able to use your scanner with a Windows computer you will need to reg ister the scanner with the Windows Device Manager Read this chapter for information on registering the scanner with different versions of Windows Scanning 35 mm Slides This chapter describes how to scan 35 mm slides Scanning 35 mm Film Read this chapter for information on scanning strips of 35 mm film Nikon Scan This chapter provides a quick overview of Nikon Scan the scanner driver software that controls your scanner For more information on Nikon Scan see the Nikon Scan Software Manual on CD Reference This chapter contains product specifications and troubleshooting information including film that cannot be scanned and scanner storage and maintenance Nikon Scan Reference Manual on CD The Nikon Scan Reference Manual describes how to use Nikon Scan 3 the software that drives your scanner This manual may be found on the software manual CD which also contains the softwar
85. key while clicking two frames to select these frames and all the frames between them The Processed Natural Tabs 7 i at 1000 These tabs allow for a quick before and after comparison showing the effects of any changes made to the image using the tools in the Tool Chest The Processed tab how the image will look when scanned at current settings Natural tab shows how the image looked before processing 125 7 The Tool Chest Layout Tools Taonl Palette 1 gt Layout Tools P Information Use these tools to select the portion of the im age to be scanned the crop and to rotate and flip the image prior to scanning You can also select a new focus area and scroll images that have been opened in Nikon Scan after scanning Crop Tool Palette 1 Layout Tools This is where you adjust the resolution and size of the image according to the output device printer or monitor on which the image will be displayed Color Balance Color Balance LCH Editor gt Unsharp Mask Use the color balance tools to make adjust ments to brightness contrast and color balance that affect the entire image 126 Information Tool Palette 1 Gives the height and width of the current crop and the coordinates of its top left corner The color value display shows the color of the pixel under the cursor before and after processing Curves Curves Color Balance gt LCH Edit
86. leunidiassnnsdderaewaraneneeeiiss 133 If the Film Jams Inside the Adapter ccccccccccccccccccceseeseeeeneceeeeeeeeeseeaeeeeneceeeseeeeeueeaaas 134 DL AUS iC ai scepter oat caus E T E E E AE E EE E E E T 137 Garin Tor YOUR SCANNel sssics sin sicisanschsiostntnsaoase AE E EEA rA TAANE ana a E 137 C WO A S a a E E E E 139 Optional ACCOSSOM CS snno ee o E rE O EAE OSTSEE 143 Options Available for the 4000 ED and COOLSCAN IV ED saassssisceeessiiieessrrrreesssrrreens 143 SpecilicatiONS serrana E E E EEE i 144 Scanner SpecitiCatONS csniconnerasgrenctesaamorecemokonesoneansnnnncbvasiewssapenetnankioctsinndteasauniecoticeanimdnnntais 144 Adapter SUCCINIC aU ONS oeeie aa iE ii a ae iisi 148 Specifications for Optional Adapters ccc cccccc ccc ceeeeecccccceeceeeeeseeeeeeceeeeeeeeeeeeseaaneeeeees 149 MOCK oroarea i tn ged cdeet tease ate E E 150 Vil B Introduction Thank you for your purchase of a Nikon SUPER COOLSCAN 4000 ED 4000 ED or COOLSCAN IV ED film scanner This manual describes how to care for install and use your scanner Be sure that you have read and understood its contents before using your scanner and leave it where those who use the scanner will read it To make it easier to find the information you need the following symbols and conventions are used This icon marks cautions information that you should read before using your Nikon scanner to prevent damage to the device This icon marks notes information th
87. loppy disk drives I CD ROM drive Jo ticrosott windows Update IV Specify a location G INFALS 4000 Win98SE x Add New Hardware Wizard Windows driver file search for the device Nikon LS 4000 ED Windows is now ready to install the best driver for this device Click Back to select a different driver or click Next to continue cA Location of driver i gt EA G AINFALS 4000 WINSSSESLS 40005 E INF Cancel Add New Hardware Wizard se Nikon LS 4000 ED Windows has finished installing the software that your new hardware device requires Cancel Confirming Device Registration Windows 98 SE After registering the scanner contirm that the device is working normally as described below 1 Turn the scanner on Make sure that the scanner is connected and turned on 2 Open the System Properties dialog From the Start menu select Settings gt Control Panel and double click the System ICON 3 Display the Device Manager The System Properties dialog will be dis ESNE KE played Open the Device Manager tab General Device Manager Hardware Profiles Performance System Microsoft Windows 98 Second Edition 4 10 2222 Registered to 50578 335 0622301 02389 aq 0007 Computer Genuinelntel x86 Family 6 Model 8 Stepping 3 255 0MB RAM Cancel Confirm that the scanner is listed under Imaging Device If Imaging Device appears inthe Device ENNOLE zjx
88. lwolw FH G1 Vly For information on optional adapters see the manual supplied with the adapter 143 E Specifications Scanner Specifications SUPER COOLSCAN 4000 ED LS 4000 ED Film Aperture Scan range Effective aperture Effective scan range Scanning system Light source Sensor Color separation Optical resolution 144 e 35 mm film Positive and negative film both color and monochrome may be used Film may be scanned in strips of up to six frames rolls of up to forty frames can be scanned using the optional SA 30 film roll adapter or mounted as 35 mm slides using mounts of from 1 0 3 2 mm in thickness and 49 0 50 8 mm in width up to fifty slides can be automatically scanned in sequence using the optional SF 200 S slide feeder e APS IX240 film APS film cartridges can be scanned with the optional IA 20 S adapter for APS IX240 film e Prepared slides Prepared slides can be scanned using the op tional FH G1 slide holder for the MA 20 S 25 1 x 36 8 mm when scanning 35 mm film in the MA 20 S FH 3 S or SF 200 S 25 1 x 38 0 mm when scanning 35 mm film in the SA 21 or SA 30 18 6 x 28 4 mm when scanning APS IX240 film 3946 x 5782 pixels when scanning 35 mm film in the MA 20 S FH 3 S or SF 200 S 3946 x 5959 pixels when scanning 35 mm film in the SA 21 or SA 30 2916 x 4453 pixels when scanning APS IX240 film 23 3 x 36 0 mm when scanning 35 mm film in th
89. m Jams Inside the Adapter If film jams inside the adapter the following error message will be displayed Nikon Scan F F The film was jammed in adapter Please remove the adapter and take out the film Click OK to release the adapter locking mechanism When the status LED to stop blinking remove the adapter from the scanner taking care to ensure that any film that may be protrud ing trom the rear of the adapter does not come into contact with the scanner s internal parts Remove the film from the adapter as described in the following section If the above error occurs when no film is inserted in the scanner it may indicate that the adapter requires cleaning Clean the adapter as described under Maintenance Caring for Adapters v SA 21 Locking Mechanism When not inserted in the scanner the SA 21 s locking mechanism is usually out of sight within the adapter A shock or blow may sometimes cause the locking mechanism to spring out from the sides of the adapter The adapter can nevertheless be inserted into the scanner normally Releasing the film adapter s lock mechanism following the instructions in the error message makes it possible to remove the adapter from the scanner Note however that film may be protruding from the rear of the adapter when removing the adapter take care that the film does not catch on the scanner s internal parts Do not reinsert the adapter immediately after removing it from the adap
90. n and click Next The Welcome Window If the Welcome program starts automatically when you insert the Nikon Scan CD click Exit to close the Welcome window 70 Add New Hardware Wizard Windows has found the following new hardware Nikon LS 40 ED Windows can automatically search for and install software that supports your hardware If pour hardware came with installation media insert it now and click Next What would you like to do ply Welcome Copyright 1998 2001 Nikon Inc and Nikon Corporation Ml GE _ Nikon Scan 3 GB ReadMe E il Zij say j il y rrean i 4 N 4 Ny A y AR N J Falin i j TAn p lt PA ll http www Nikon Asia com kitp www Nikon Euro com hitp www Nikon USA com Click Finish Click Finish to complete installation Add New Hardware Wizard Nikon LS 40 ED Windows has finished installing the software you selected that your new hardware device requires ti Cancel Restart the computer Click Yes to restart the computer x 2 You must restart your computer before the new settings will take effect Do you want to restart your computer now A Zo lt 9 Confirm device registration JA Confirm that the scanner has been correctly registered with the system as described in Confirming Device Registration Windows Me J 72 71 m Confirming Device Registration Windows Me After regist
91. n the Crop palette Tool Palette 1 gt Layout Tools gt Information Click The Crop palette contains three options for determining output size Keep this crop Keep this output size and Keep this file size 93 Output units menu F Crop C Keep this crop wE 583 H 2 481 Pixels Keep this output size wha o H Bo fim 4 C Keen this file size File size text box E og ME Output size text boxes Scale 4 bli 14 15 Resolution 240 Pixels Inch 5 ml Custom Output resolution menu Scale slider Resolution text box Pg For more information on 46 The Crop palette og e Keep this crop Choose Keep this crop when you want to select the precise area to be scanned using the mouse then adjust the output resolution and size according to how the image will be used Enter a value for resolution suited to the device on which the image will be printed or displayed in the Resolution text box or select a resolution that matches the device from the options listed in the output resolution menu You can then choose the units for output size trom the output units menu and enter a value for either Width or Height in the output size text boxes The other dimension will be adjusted automatically to maintain the crop se lected in the preview area e Keep this output size Choose this option when you want to select the general area to be scanned using the mouse then specify the exac
92. n the list drag the scroll bar at the right of the list until it is displayed Be sure to choose the driver that has xp in the file name 4 Click Continue Anyway Click Continue Anyway to begin instal lation of the files needed to register the scanner D Click Finish Click Finish to complete installation 6 Confirm device registration Found New Hardware Wizard Please select the best match for your hardware from the list below P i Nikon SUPER COOLSCAN 4000 ED CAN 4000ED Unknown Nikon Corporation d inf ls4000 win98se ls4000se inf CAN 4000ED Unknown Nikon Corporation d inf ls4000 win2000 ls40002k inf lt gt A This driver is not digitally signed Tell me why driver signing is important Hardware Installation The software you are installing for this hardware Nikon SUPER COOLSCAN 4000 ED aq 0007 has not passed Windows Logo testing to verify its compatibility with Windows xP Tell me why this testing is important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing Continue Anyway STOP Installation Found New Hardware Wizard Completing the Found New Hardware Wizard The wizard has finished installing the software for lt lt is Nikon S
93. n turning the scanner on with the MA 20 S slide mount adapter in place be sure that the FH 3 film holder is not inserted Leaving the FH 3 in the scanner can prevent the scanner from initializing normally The status LED should blink slowly about twice every three seconds while the scanner initializes If the LED flashes rapidly about five times a second there may be a problem with the scanner or with the connection to your computer Try turning the scanner off waiting for five seconds and then turning the scanner on again Pg For more information on 29 Device registration Windows only 130 Troubleshooting 28 Device Registration Windows Only The first time you connect the scanner to a Windows computer you will need to register the scanner with the system by in Stalling the hardware drivers Registering the 4000 ED with Windows Windows XP Home Edition Windows XP Professional E eee oe Fe Ee E ee ne ern 30 Windows 2000 Professional a een 36 Windows Millennium Edition Me 44 Windows 98second Edition SE ese 50 Registering the COOLSCAN IV ED with Windows Windows XP Home Edition Windows XP Professional Ree rn E E E E TN S7 Windows 2000 Professional oaeee 63 Windows Millennium Edition Me 70 Windows 98Second Edition SE 76 29 aq 0007 Registering the 4000 ED with Windows Windows XP Home Edition Windows XP Professional Registering the Scanner with Wind
94. n twenty and ninety percent no condensation Cleaning the SA 21 Strip Film Adapter When cleaning the strip film adapter press the release button on the upper cover and open the front panel Open and remove the upper cover Upper cover Release button LAN Front panel 139 E Release the frame lock lever as shown below and open the roller frame Roller frame Frame lock lever Using a dry cotton swab or a swab that has been slightly dampened with water and wrung out remove dirt from the rollers while turning the toothed wheel slowly in either direction Dry the rollers with a dry cotton swab or leave the roller frame open until the rollers dry m The roller frame should not be removed from the adapter When opening the roller frame stop when you feel resistance Forcing the frame open could result in damage to the adapter If the rollers inside the adapter are not clean even film that is neither curled nor warped may jam in the adapter several times in succession possibly resulting in damage to the film Should this occur you will need to clean the rollers If the film continues to jam after the rollers have been cleaned consult with your nearest Nikon service representative 140 When rotating the rollers turn the toothed wheel slowly with the ball of your thumb Do not use force or attempt to turn the wheel with a screwdriver or other rigid object as this could deform the wheel Rollers Toothe
95. naniini aaan 10 Installing the Device Drivers Windows Only cccc cece cece seeecceceeceeeeeeeseseneeeeeeeeeeeeeaaaas 11 Istana NIKON SCAN errenneren eE aE aA AEDE E EO Aaa 16 Installing Nikon Scan under WINGGWS ssessserrsessssniieaeiaain akna a EaR 16 Installing Nikon Scan on a Macintosh 0 0 ccc ccc ccce eee eeeeeeeeeeeeeceeeeeessaeeeeeeeeesaaeeeeeeeeaas 21 Connecting the Scanner sce stcteccecacnndscendcececcestgewassesesss0cesee ateasenedvatapesmedinesnieneneressaeeme 25 Connecting the Power CAD Ci cscscsacsenconcenasseasaadsibaimnccenunaansaaonmenreendiinadssadaadsesanaaesaabniades 25 Connecting the Interface Cable 4000 ED sessssnniusssrsiinuesssrinrssnrrrnrusrrrrrrenrrrrrreee 26 Connecting the Interface Cable COOLSCAN IV ED ccc ccccccecccccceeeeeeceeeeeeeeeeeeeeeeeeeees 27 T rn the Scanner ON ccs coca ase re ccc ns ses ee see ro i eN adaa ebrii oinin 28 Device Registration Windows Only cceeeeeseesseeeeeeeceesseeeeeeseaeeneeeeeeeaes 29 Registering the 4000 ED with WINCOWS cccccceeeeeeeeeeeeeseeseeeeeeeeeeseneaaaeeseeeeeeeeeees 30 Windows XP Home Edition Windows XP Professional 00 ccccceeeeseeecee cece eeeeaeesaeesaees 30 Windows 2000 PIOTESSIONG arroen ukancsesnstccecnteaseriehrsnautscechsanchehcinsdwiasertaetcdcatiice 36 Windows Millennium Editon ME iraani neea E aaa e AE REEE EANO 44 Windows 98Second Edition SE sicicacsccecdcateacencieacusdeneandsndebsdeewdauiwadunvanee
96. nd connect the scanner directly to the computer If this does not solve the problem uninstall other software that uses the same interface and re install Nikon Scan e Your computer system does not meet the minimum system requirements See the Nikon Scan 3 Reference Manual for more informa tion on system requirements Your computer does not e The interface board is not compatible with Nikon Scan recognize the scanner If you are using the 4000 ED check the compatiblity infor mation provided with your scanner to determine whether the IEEE 1394 Firewire board you are using is compatible with Nikon Scan if you are using Windows computer with a built in IEEE 1394 port check the make and model num ber of your computer Updated compatiblity information may also be available on the Nikon support web site for your area If your IEEE 1394 Firewire board is not compat ible with Nikon Scan install the REX PFW2W IEEE 1394 in terface board included with your scanner desktop com puters or purchase one of the recommended PCMCIA in terface cards laptop computers Note that the COOLSCAN IV ED will only function with built in USB ports e The interface board is not correctly installed Check the documentation for your IEEE 1394 or Firewire interface board e The device driver for your scanner is missing or cor rupted Windows only Check that the driver is correctly installed e Nikon Scan is not correctly installed Uninstall and re install the softwa
97. ner is off a on the status LED does not Turn the scanner on 28 light e The power supply to scanner has been interrupted Try plugging a different device into the outlet used by the scanner to determine whether the problem is caused by a failed fuse or circuit breaker e The FH 3 film holder was inserted Turn the scanner off remove the FH 3 and turn the scan The status LED flashes ner on again rapidly scanner not e A scanner hardware malfunction has occurred connected to computer or Turn the scanner off and disconnect it from the computer computer off Wait five seconds then turn the scanner on again If the problem persists contact your retailer or Nikon service rep resentative for advice 130 e A connection error or scanner hardware malfunction has occurred Turn the scanner and computer off and disconnect the scan ner from the computer Wait five seconds then turn the scanner on again If the status LED flashes rapidly a hard ware malfunction has occurred Contact your retailer or Nikon service representative for advice If the status LED blinks slowly at first and then glows steadily turn the scan ner off and reconnect it to your computer then start your computer and turn the scanner on If the status LED flashes rapidly after the scanner is reconnected and turned on there may be a problem with the interface between the scanner and the computer Try the following measures to resolve the problem e Disconnect
98. ning 35 mm film in the SA 21 2736 x 4104 pixels when scanning 35 mm film in the FH 3 S 2870 x 4203 pixels when scanning 35 mm film in the MA 20 S 1836 x 3067 pixels when scanning APS 1X240 film Scanning system Fixed film movable plane single pass optical scanning system Light source Red green and blue RGB LEDs Sensor 2870 pixel linear CCD image sensor Color separation Performed by RGB color LEDs Optical resolution Maximum 2900 pixels per inch Analog to digital A D conversion 12 bits per color RGB Output Full color 8 or 16 bits per color RGB Focus Autofocus Manual 146 Scanning time Duration of Scanning on processes Preview Computer FMV715GTX6 Pentium4 1 5GHz RAM 1GB OS Windows 2000 Software Nikon Scan 3 1 Adapter MA 20 S Slide Mount Adapter Input Resolution 2900dpi Scan Bit Depth 8bit CMS On Film Positive Interface USB 1 1 compliant Power supply AC 100 240 V 50 60 Hz Maximum power consumption while scanning Not exceeding 20W Power consumption at standby Not exceeding 10W Operating environment Temperature 10 35 C 50 95 F e Humidity 20 60 Dimensions 93 x 169 x 315 mm 3 66 x 6 65 x 12 40 W x H x D Weight Approximately 3 kg 6 Ib 11 1 oz accessories not included Installation Vertical Horizontal 147 n Adapter Specifications MA 20 S SLibEe Mount ADAPTER Film Dimensions Weight Operating Mode FH
99. ning images destined for the Macintosh platform Press the Macintosh button Ifyou will be scanning images destined for the Windows platform Press the windows button This is select a group of color spaces that contain the optimal gamma characteristic for the selected platform Color Space Wizard IF you press the Windows button you vill be presented with seven color spaces that use a gamma value of 2 2 If you press the Macintosh button pou will be presented with three color spaces that use a gamma value of 1 8 19 EE 6 Choose an RGB color space profile from Wizard Windows the list and click OK More information Wizard Windows There are seven choices of color spaces here about the different profiles is available in es ars T the Nikon Scan Reference Manual 4 Adobe RGB 1998 5 CIE RGB 6 Wide Gamut RGB 7 Wide Gamut RGB compensated 1 gives you the most vivid color reproduction and it is recommended as the standard color space for web authoring However it may be too saturated in places 7 maintains the most tonal information possible but it may look flat 2 thru 6 represent values between these two extremes Please choose one and press the OK button sRGB C Bruce RGB C NTSC 1953 C Adobe RGB 1998 C CIE RGB C Wide Gamut RGB C Wide Gamut RGB Compensated 4 sample image is being displayed using the selected color space profile If you think that all color spaces are still to
100. nner or computer or interfere with their correct functioning 4000 ED Computer Align the curved portion of the con nector circled with the matching portion of the connector on the scanner or computer IEEE 1394 connector v Four Pin Connectors Some computers for example SONY VAIO laptop computers and interface boards are equipped with a 4 pin DV connector You will need to purchase 6 pin 4 pin cable or adapter to connect the scanner 26 Connecting the Interface Cable COOLSCAN IV ED After confirming that the scanner is off connect the supplied USB cable to the scanner using the B connector and insert the A connector to the computer s USB port Connect the cable as shown Attempting to insert the connector in another orientation could not only damage the connector but also damage the scanner or computer or interfere with their correct functioning COOLSCAN IV ED e Using the USB cable provided with your scanner con nect Connector B to the connector on the rear of the scanner and Connector A to your computer SSS as Connector A Connector B connect to computer connect to scanner 27 the Scanner On Press the power switch to turn the scanner on The status LED will blink while the scanner initializes When initialization is complete the status LED will glow steadily j Ke Status LED Power switch off Blink Glow steadily We Power switch on Whe
101. nt E E Fe 72 D Confirm that the scanner is working properly Double click the listing for your scanner 2 x that appears under Imaging Device The General Driver scanner Properties dialog will be displayed Click the General tab and confirm that a a This device is working properly appears Daves bees diame Deves under Device Status If another mes Manufacturer Nikon Corporation sage IS displayed proceed to Updating Hardware version Not available the Device Driver Windows Me EJ 74 Device status This device is working properly m Device usage IV Exists in all hardware profiles di Al NVDS1009 73 i Updating the Device Driver Windows Me COOLSCAN IV ED If the scanner is not listed under Imaging Device in the Device Manager or the message This device is working properly does not appear in the Properties dialog you will need to reinstall the device driver as detailed below 1 Open the scanner Properties dialog Display the Device Manager as described in steps 1 3 of Confirming Device Registration Windows Me on 72 If the scanner is listed under Other devices or appears next to a 1 or x double click the entry for the scanner to display the scanner Properties dialog 2 Click Update Driver Open the Driver tab and click Update 2j x Driver General Dri
102. nual for the Nikon Scan driver software together with in stallers for Adobe Acrobat Reader the software used to view the manual Image Editing Software CD ROM 1 COOLSCAN IV ED only With this application installed on your com puter you can scan images directly from Nikon Scan into this software where they can be ed ited and saved to disk Nikon Quick Start Guide Quick Start Guide 1 This guide provides you with the infor mation you need to get started with your Nikon scanner Keep the Adapter Slot Closed In order to ensure that your scanner always produces the best possible results remove the adapter and close the sliding cover when the scanner Is not in use vy Never remove an adapter from the scanner without first ejecting the film and check ing that the status LED on the front of the scanner is glowing steadily Do not insert or remove adapters insert or eject film or turn the scanner off while the LED is blinking vy After using the scanner eject the film from the adapter and turn the scanner off then remove the adapter and close the sliding cover Choose a Location Before connecting the power and interface cables choose a flat stable location for your scan ner close to the computer and to a suitable power outlet Do not install your scanner where m it would be exposed to direct or reflected sunlight m it would be subject to condensation or to drastic changes in
103. o light press the Too Light button Too Light The installation complete dialog will be displayed Click Finish to exit the InstallShield wizard D Nikon Scan 3 Setup Complete Nikon Scan 3 Setup has successfully installed Nikon Scan 3 1 1 Before you can use the program you must restart your computer Nikon Scan 3 1 Setup Yes want to restart my computer now No will restart my computer later Remove any disks from their drives and then click Finish to complete setup e 8 Once the computer has restarted take a few moments to view the ReadMe file which may contain important information that could not be included in this manual This completes installation of Nikon Scan 3 20 Installing Nikon Scan on a Macintosh Before installing Nikon Scan turn your computer on and wait for it to start up Check to make sure that e The scanner is not connected to your computer e Your computer satisfies the Nikon Scan 3 system requirements see page 5 of the Nikon Scan Reference Manual for details e No other applications including anti virus software are running Installation 1 Insert the Nikon Scan 3 CD into the CD o Al Nikon Scan 3 1 3 ae ROM drive When the Nikon Scan 3 1 2 window opens on the desktop double click the Nikon Scan Installer icon for the language of your choice Nikon Scan Installer 0090 Nikon Scan 3 1 3 Mage SEs
104. of the tone range edit chroma to modify color saturation or vividness and change one set of hues or colors in the image to a different color Unsharp Mask The tools in the Unsharp Mask palette sharpen outlines either throughout the image or only where specific colors predominate To open any of the above palettes click the triangle at its top left corner Tool Palette 1 Layout Tools gt Information Crop wag Color Balance x LCH Editor z Unsharp Mask x Digital ICE cubed gt Analog Gain Scanner Extras Pg For more information on 63 Curves 76 Color Balance 78 The LCH Editor 85 Unsharp Mask 95 7 To view the effects of any changes that have been made and compare them with the original use the Processed and Natural tabs in the preview area to switch back and forth between the processed and original image The image produced when you click the Scan button to open the image in the host application will be the same as the image in the Processed tab The Processed Natural Tabs File Size 27 ME Analogan Neutral Digital ROC Neutral Digital GEM Neutral Digital ICE Off MultiS ample 14 Bit Depth amp E G When using Nikon Scan as a stand alone application you can use the Ctrl T Windows or 3 T Macintosh keyboard shortcut to switch between the Processed and Natural tabs 96 1 1 Click the Scan button Click the Scan button to begin scanning Scan bu
105. on 46 If the scanner is listed under Other devices or appears next to a 1 or x double click the entry for the scanner to display the scanner Properties dialog 2 Click Update Driver Open the Driver tab and click Update Driver Nikon SUPER COOLSCAN 4000 ED Pre verti General Driver Nikon SUPER COOLSCAN 4000 ED Driver Provider Nikon Corporation Driver Date 03 05 2001 Digital Signer Not signed To view details about the driver files loaded for this device click Driver File Details To update the driver files for this device click Update Driver Update Driver OK Cancel 3 Insert the Nikon Scan 3 CD The Upgrade Device Driver wizard willbe MMA displayed Holding down the shift key to prevent the Welcome program from start ing automatically insert the Nikon Scan 3 CD into the CD ROM drive The Welcome Window If the Welcome program starts automati Automatic search for a better driver Hlecommended cally when you insert the Nikon Scan CD click Exit to close the Welcome window This wizard searches for updated drivers for Nikon SUPER COOLSCAN 4000 ED Windows can search for and install an updated driver to replace the one currently being used by your hardware Or you can specify the location of another driver What would you like to do 48 4 Select the search option Select the search option and click Next Select LS4000ME INF Sel
106. onfirm that your 5 csse scanner is listed Bg Fore crt IDE ATAJATAPI controllers If the Scanner Is Not Listed tno If your scanner is not listed under Imag Ie aa ing devices proceed to Updating the Epica Device Driver Windows XP RJ 61 ace SCSI and RAID controllers Sound video and game controllers Se Storage volumes 59 n D Confirm that the scanner is working properly Double click the listing for your scanner that appears under Imaging devices The scanner Properties dialog will be dis played Click the General tab and con s Nikon COOLSCAN IV ED firm that This device is working properly appears under Device Status If another iii i message is displayed proceed to Updat ESE RRR TIRES ing the Device Driver Windows XP EQ ae sai 6 1 Jevice status This device is working properly Nikon COOLSCAN I ED Properties General Driver If you are having problems with this device click Troubleshoot to start the troubleshooter Troubleshoot Device usage Use this device enable COOLSCAN IV ED 60 Updating the Device Driver Windows XP If the scanner is not listed under Imaging devices in the Device Manager or the message This device is working properly does not appear in the Properties dialog you will need to reinstall the device driver as detailed below 1 Open the scanner Properties dialog Displa
107. ontents Product DOCUMENTATION 0 0 eke eeececcceccceeecceecueececeuecevecaeeaeeeeeentereeeaeerecteeeaeereeeaeeaeeeeneanenans OMe VOI I E EEA E EE AEE E E E T EAE ii O ee a a cane eeoe viii BS CU e AOE E E E E E E E E 1 Before Using Your Scanner sidtiaricsscsscsweeseuestentd any sktiariavainniediciantttagicnteteniancineminestees 2 Comectma the Sanel a rs on csaciersiege ceeaiease tapseecenatdecendcnien stieawadtntioancscneeadeceiaeinddiee Wenciuceteeders 2 Using the Scanner with a Windows Computer sss ssssssiiuuesssririnessrrrrreennrrrrrererrrrre gt 2 Get to Know Your Scannel seiiievdsnencinnccinntionciaeanineavionbinniauieiiedodiniataniotannaseieiedioien 3 YOUN SCANNET ssiasccssavsscusanapoiavisnnvdiiasevadavnshnusaauuiaceainwiinecdiadinadhisanaeeraiunenveiaheviasitsnteneenactianeey 3 TES GGL erSS E E EE eee mn E A ener eee ee ee eee ee E eee ee 4 Keep the Adapter Slot Closed ou icc cccccccccccccccseeeecceseeseeeeecceeeeseeeceeceessaeeeeeeeeeaeeeeeeeeeeaaes 6 Choo aA LOCO sarrianet E EAEE Pe TCI In CON Sern ato nery eretne Nate woe 6 Protect vour Fii seasea e a aE EE EEn A P Ena EE iaaa 7 Using the 4000 ED with Other Devices ssssnnnnnssnninnussnrrrnuseerriirurerrrrrrenrrrrrrererrrren 8 Using the COOLSCAN IV ED with Other Devices 0 0 00 cccecccccceceeccceceesseeeeeeceeesaeeeeeeeeeaans 8 Installing the IEEE 1394 Firewire Interface Board 4000 ED Only 9 Installing the Interface Board 4000 ED ONIY sriseiiseisan
108. or gt Unsharp Mask One of three color editing tools offered by Nikon Scan the curves tool is useful when ad justing contrast and making changes to color balance that effect only a specific portion of the tone range shadows mid tones or high lights LCH Editor Curves Like the Curves tool the LCH editor can be used to adjust brightness and contrast in shadows mid tones and highlights It also incorporates hue and chroma editors which provide ex tremely flexible tools for adjusting color Unsharp Mask gt w Unsharp Mask 5 Digita ILE cubec gt Analog Gain Scanner Extras Unsharp mask increases the sharpness of the image by making edges more distinct either over the entire image or in areas where spe cific colors are prominent Analog Gain gt wv Unsharp Mask gt Digital ICE cubed gt Analog Gain SACanner CHiras Using analog gain you can adjust colors by di rectly altering the exposure value for each of the colored elements in the scanner s light source Digital ICE cubed Unsharp Mask P Digital ICE cubed Scanner Extras Three tools are available e Digital ICE reduces the effects of dust and scratches e Digtial ROC restores colors lost through fad ing e Digital GEM reduces the effect of film grain Scanner Extras gt wv Unsharp Mask b Digital ICE cubed gt Analog Gain Scanner Extras These tools offer control over fe
109. or click Browse to choose another location 1 Setup will install Nikon Scan 3 1 in the following folder To install to this folder click Next To install to a different folder click Browse and select another folder Destination Folder C Program Files Nikon NkScan30 Browse lt Back cr Cancel Once the Nikon Scan program files have Color Space Wizard been copied to disk a color space selec tion wizard will be displayed Click Use This i setup that determines the basic characteristics of Wizard to have the wizard assist you In output image l lt helps vou to select one of ten AGB color spaces choosing a color space profile recom mended or Use name list to choose a Do vou wish to select a color space from the name list or Use the Profile Selection Wizard custom profile see the Nikon Scan Refer ence Manual for details The color space Use name list protile selected during installation can be changed at any time as detailed in the Preferences section of the Nikon Scan Reference Manual Choosing the correct color space profile is very important if the scanner is to be used in a professional set ting for example as part of a production workflow More information about the color management system used in Nikon Scan 3 may be found in the Nikon Scan Reference Manual Clicking Use Wizard in the Color Space Wizard dialog displays the dialog shown at rig ht Click Windows IF pou will be scan
110. or forcibly tugged or bent In the event that the insulation is damaged and the wires become exposed contact your retailer or Nikon service office for information on repair or replacement Continued use could result in fire or electric shock Do not handle the plug when your hands are wet Doing so could cause electric shock Should you notice dust on or near the metal parts of the plug remove it with a dry cloth Continued use could result in fire or electric shock CAUTIONS Do not handle the equipment when your hands are wet Failure to observe this precaution could result in electric shock Keep equipment out of reach of children Failure to observe this precaution could result in injury Install the scanner only as directed in this manual Failure to observe this precaution could block the scanner s vents and cause the power source to overheat possibly resulting in fire Place on a stable surface e Do not use the equipment on an unstable surface or on a surface that is not level The equipment could fall resulting in injury or in damage to the scanner e The scanner contains glass parts Caution is advised in the event of breakage to prevent injury from broken glass Do not place heavy objects on the equipment Do not place heavy objects on the equipment as either the objects or the equipment could overbalance or fall causing injury Unplug the equipment before cleaning For your safety turn off and unplug the scanner when cl
111. ows 2000 Professional COOLSCAN IV ED After registering the scanner confirm that the device is working normally as described below 1 Turn the scanner on Make sure that the scanner is connected and turned on 2 Open the System Properties dialog From the Start menu select Settings gt Control Panel and double click the System ICON 3 Display the Device Manager The System Properties dialog will be dis 2j xi played Open the Hardware tab and click General Network Identification Hardware User Profiles Advanced Device Manager Hardware Wizard Ea The Hardware wizard helps you install uninstall repair ety 5 unplug eject and configure your hardware Hardware Wizard m Device Manager fm The Device Manager lists all the hardware devices installed as on your computer Use the Device Manager to change the properties of any device Driver Signing Device Manager Hardware Profiles Hardware profiles provide a way for you to set up and store xa different hardware configurations Hardware Profiles Cancel Confirm that the scanner is listed under Imaging devices If Imaging devices appears in the De iol x vice Manager click the to its left to aetion view gt view the imaging devices currently regis tered with Windows Confirm that your ish Doel Disk drives scanner is
112. ows XP 1 Turn the scanner on The first time the computer detects the FPT TP EEE scanner Windows will display the dialog eena TARARE shown at right Hardware Wizard This wizard helps you install software for Nikon LS 4000ED IEEE 1394 SBP2 Device If your hardware came with an installation CD lt 6 or floppy disk insert it now What do you want the wizard to do Install the software automatically Recommended Install from a list or specific location Advanced Click Next to continue 4000 ED Ce Insert the Nikon Scan 3 CD Holding down the shift key to prevent the Welcome program from starting automatically insert the Nikon Scan 3 CD into the CD ROM drive The list of drivers shown in step 3 will be displayed If the List of Drivers Is Not Displayed If the list of drivers shown in step 3 Is not displayed automatically select the automatic install option in the dialog shown above and click Next Logging On Log on as the Computer Administrator when registering the scanner The Welcome Dialog If the Welcome program starts automatically when EM you insert the Nikon Scan CD click Exit to close the 9 7 yen me and Nikon comoraton Welcome window GR Viikon Scan 3 GR Reede http www Nikon Asia com hitp www Nikon Euro com hittp www Nikon USA cam 30 3 Select ls4000xp inf Select Is4000xp inf in the list of drivers and click Next Is4000xp int If ls4000xp inf is not visible i
113. ption and click Next CE Install Hardware Device Drivers Fea Rast 4 device driver is a software program that enables a hardware device to work with cy an operating system This wizard upgrades drivers for the following hardware device Nikon COOLSCAN IV ED n Upgrading to a newer version of a device driver may add functionality to or improve the performance of this device What do you want the wizard to do Search for a suitable driver for my device recommended Display a list of the known drivers for this device so that can choose a specific driver lt Back n Cancel Insert the Nikon Scan 3 CD Holding down the shift key to prevent the Welcome prog ram from starting automati gi e ia A to search for driver files D cally insert the Nikon Scan 3 CD into the D _ R O M d riv G S e e ct C D S R O M d r i ves Search for driver files for the following hardware device i LS 40 ED and click Next Q Th W j W e a The wena eee be apps bay its ana iaa on your computer and in 5 e elcome indow any of the following Gs ional search locations you specify l l lt oO If the Welcome program starts automati natte iay Gh a D baaa ik Naa S AE min i i Optional search locations cally when you insert the Nikon Scan CD Tl Floppy disk drives IV CD ROM drives I Specify a location Microsoft Windows Update click Exit to close the Welcome window lt Back _Net gt Cancel 6
114. r It will installed on Macintosh computers running Mac OS X The following limitations apply The LS 2000 and COOLSCAN III are not supported The menus and dialogs shown in the Nikon Scan 3 Help file are for version 3 1 2 Installing Nikon Scan under Windows Before installing Nikon Scan turn your computer on and wait for Windows to start up Check to make sure that 16 The scanner is not connected to your computer Your computer satisfies the Nikon Scan 3 system requirements see page 5 of the Nikon Scan Reference Manual for details No other applications including anti virus software are running You have completed the IEEE 1394 update Windows 98 SE with SUPER COOLSCAN 4000 ED only see page 17 for details Updating the IEEE 1394 Drivers Windows 98 SE Only Before installing Nikon Scan 3 under Windows 98 SE users of the SUPER COOLSCAN 4000 ED will need to complete the IEEE 1394 driver update as described below 1 Holding down the shift key to prevent the Nikon Scan 3 installer from starting automati cally insert the Nikon Scan 3 CD into the CD ROM drive if the installer starts click Exit to close the Welcome dialog Double click the My Computer icon Click the Nikon Scan 3 CD icon with the right mouse button and select Explore from the menu that appears Open the Microsoft folder and double click 242975USA8 exe Follow the on screen instructions to complete the update VI A WN The dialog shown at r
115. rain using the Digital GEM for Grain Equalization and Management slider Moving the sliders to the right increases the effects of Digital ICE To view the effects of Digital ROC or Digital GEM in the preview image click the Redraw button Because of the complexity of the processing involved Digital ICE operations require additional time to perform The time required is determined in part by the processing power of your computer and in part by the size of the image Pg For more information on 51 Digital ICE 91 _ 92 Select a crop Select a portion of the image for scanning This selection is referred to as the crop Click the Crop tool 3 in the Layout Tools palette and drag the mouse to select a crop The borders of the crop are indicated by a dotted line Selecting the Entire Image Double click inside the current crop to select the entire image When the entire image is selected the borders of the crop are not indicated by a dotted line a Processed F Li Selected area crop The size of the crop can be changed by dragging its boundaries To change the position of the crop place the cursor inside the selected area and drag it to a new location 9 Choose an output size and resolution If desired you can specify the dimensions and resolution of the final image output size and resolution Click the triangle at the top left corner of the Crop palette to view the controls i
116. re K Bm WO L WO mB N WO JO 132 When Film Jams in the SA 21 When film jams in the SA 21 Nikon Scan will display an error and the scanner status LED will flash at rate of about five times per second How you will handle the jam depends on whether the film is caught inside the adapter of if the problem occurred while the film was loading If the Film Jams During Loading If the scanner is unable to load the film the film will automatically be ejected and the following error message will be displayed Nikon Scan xi al d The scanner could not load the film Please refer to your user manual L Click OK and check whether the film is suitable for use in the SA 21 If it is wait for the status LED to stop flashing and then reinsert the film If the film can not be scanned in the SA 21 follow the instructions in Film That Can Not Be Scanned in the SA 21 If the above error occurs when no film is inserted in the scanner it may indicate that the adapter requires cleaning Clean the adapter as described under Maintenance Caring for Adapters If the Film Is Not Ejected If the film is not ejected after you have clicked OK to close the above error message follow the instructions under If the Film Jams Inside the Adapter vy Pg For more information on 102 Film that can not be scanned in the SA 21 105 Using the FH 3 139 Cleaning the SA 21 133 7 If the Fil
117. resten w om Mind ision Software Nikon Scan Installer SB Easy Install Go to Tech Support Site Click Install Nikon Scan 3 1 and Nikon Scan Plugin 3 1 are installed into the respective folder as specified by the user under Install Location Nikon Scan Plugin 3 1 is installed into the Plug ins folder SUPER COOLSCAN 8000 ED SUPER COOLSCAN 4000 ED LS 2000 COOLSCAN IV ED COOLSCAN III Drivers are placed in the Nikon MAID folder USB drivers and FireWire drivers are placed in the Extensions folder Install Location The folder Nikon Software will be created on the disk MacOS9_En Nikon Scan Installer 0O 9 f Read Me Easy Install i Click Install Nikon Scan 3 is installed into the Applications folder SUPER COOLSCAN 8000 ED SUPER COOLSCAN 4000 ED COOLSCAN IV ED Drivers are placed in the Application Support folder m Install Location f Quit j gt E The folder Nikon Software will be created in the folder Applications on the disk MacOSXDe 4 Once the Nikon Scan program files have been copied to disk a color space selec tion wizard will be displayed Click Use Wizard to have the wizard assist you in choosing a color space profile recom mended or Use name list to choose a custom profile see the Nikon Scan Refer This is a setup that determines the basic charact
118. roperties of any device Hardware Profiles 2 Hardware profiles provide a way for you to set up and store different hardware configurations Hardware Profiles Device Manager File Action View Help H e2 amp 1 Computer Disk drives 2 Display adapters DVD CD ROM drives Floppy disk controllers 3 Floppy disk drives jy IDE ATA ATAPI controllers Mice and other pointing devices F Monitors B Network adapters Ports COM amp LPT 8 Processors Sy SBP2 IEEE 1394 Devices Sound video and game controllers System devices Universal Serial Bus controllers 5 Confirm that the scanner is working properly Double click the listing for your scanner that appears under Imaging devices The scanner Properties dialog will be displayed Click the General tab and confirm that This device is working properly appears under Device Status If another message is displayed proceed to Updating the Device Driver Windows XP EQ 34 Nikon SUPER COOLSCAN 4000 ED Properties k General Driver 8 Nikon SUPER COOLSCAN 4000 ED Device type Imaging devices Manufacturer Nikon Corporation Location LUN 0 If you are having problems with this device click Troubleshoot to start the troubleshooter Troubleshoot Device usage Use this device enable vl aq 0007 33 4000 ED Updating the De
119. s a software program that makes a hardware device work i Cancel Add New Hardware Wizard What do you want Windows to do Display a list of all the drivers in a specific location so you can select the driver you want lt Back Next gt Cancel ply Welcome x Copyrig t 1998 2001 Nikon Inc and Nikon Corporation Ni Nikon Ea S Wl GR _ Nikon Scan 3 HR Reade Ba eit ii hitp www Nikon Asia com kitp www Niken Eure com http www Nikon USA com 3 Select Specify a location Select Specify a location and click Browse Select the Ls40 folder The Browse for Folder dialog will be dis played Click on the next to the Nkscan and then INF folders to dis play the Ls40 folder Select the Ls40 folder and click OK Confirm the file path The dialog shown at right will be displayed Confirm that the path INF LS40 appears after the drive letter of the CD ROM drive and click Next If the Correct Path Is Not Displayed If the correct path is not displayed repeat steps 3 5 to select the correct path Add New Hardware Wizard Windows will search for new drivers in its driver database on your hard drive and in any of the following selected locations Click Next to start the search T Floppy disk drives I CD ROM drive T Microsoft Windows Update V Specify a location Select the folder that contains
120. sdaeavetecuneusdveucuvee 50 Registering the COOLSCAN IV ED with Windows eseeeeeeeeeeeeeeeeeeeeeeseeeeeeeeeeeees 57 Windows XP Home Edition Windows XP Professional 00 cccccceeeeeeeeseeeeeeeeeeeeesaneeraees 57 Windows 2000 Prorosslanal oreren E R aaa 63 Windows Millennium Edition Me cccccccccecececececececeeecereteceeereeeeeeereeeeevereeereneneeeneeens 70 Windows 98 Second Edition SE sentenssa nni ss ee sic ee eens eet 76 vi Scanning 35 mm Slides cetacean seis et atest eae neeaeeemeeeeesdtanedeaesatetewdesvexuess 83 Step 1 Ready the Slide wainsnacconskicnssdnnedadanduiicdnvansndtacnansanesdesacadustuiinenaxiimaedanguvdninacdoadaues 84 Step 2 lnsert the Adapter accccecsncdsocienccs cdivesendeehadsutdudia bocavehcdacutansiedeusareveeinidasdcacendeneees 84 Step 3 linsert the SIde coeciesriniriniresinn er ner En G NEEE REO Naio AREER TEN REE 85 Step 4 Scan the Slide eee cccecccceceseeeeecaeeeeceasseeeceueeeseaaeeeeeeeaeeesesageeeeseaeeeeesegeeeees 86 EE E a E EE TAE ONIE ae sees A EEE vena 86 Scanning SSM FIM scesessssiecesesnsucnvecdssdsencesseviiasecseudiantivenstiuscduaedcaniecasdaumencss 101 Film That Can Not Be Scanned in the SA 21 aaannnnaannnnnnannnnnnnnnnnnnnnnnnnennnnnnnnnnneennnnne 102 Flim inat can Not pe UST erareco aee ni Rae ESE NEEESE EE AAEE 102 Film That Must Be Repaired Before Use s n snnnneessesssssninnnriuessnsnrririrriressesrrrrrrrirereeen 103 Using the FH 3 sreeecccs
121. seceeseaceeneeessencnsneecasesererenesenees sue seusensecsensussansanesassecsaseseresennesessnanannesmessensseennes MV Exists in all hardware profiles Updating the Device Driver Windows 98 SE If the scanner is not listed under Imaging Device in the Device Manager or the message This device is working properly does not appear in the Properties dialog you will need to reinstall the device driver as detailed below 1 Open the scanner Properties dialog Display the Device Manager as described in steps 1 3 of Confirming Device Registration Windows 98 SE on 53 If the scanner is listed under Other devices or appears next toa I 2 or x double click the entry for the scanner to display the scanner Prop erties dialog 2 Click Reinstall Driver Open the Driver tab and click Reinstall CIZME ETE a x Driver General Driver op Nikon LS 4000ED IEEE 1394 SBP2 Device Device type Other devices Manufacturer None specified Hardware version Not available m Device status The drivers for this device are not installed Code 28 To reinstall the drivers for this device click Reinstall Driver Reinstall Driver 3 Click Next When the Update Device Driver Wizard is displayed click Next 4 Select the search option Select the search option and click Next Update Device Driver Wizard What do you want Windows to do rae E AA S d Display a list of all the
122. sensesesssenssersnsnsessssssnnssessnsonssnsnsssns Display a list of all the drivers in a specific location so you can select the driver you want lt Back EC Cancel Add New Hardware Wizard Windows will search for new drivers in its driver database on your hard drive and in any of the following selected locations Click Next to start the search T Floppy disk drives T CD ROM drive Jo Micrasofi windows Update I Specify a location 5 Select The updated driver Recom mended NEC Firewarden OHCI Com pliant IEEE 1394 Host Controller and click Next The dialog shown at right will be dis played Click Next If prompted to insert a disk insert the Windows 98 Second Edition CD into the CD ROM drive and click OK Ifa message is displayed stating that the computer was unable to find a file on the Windows 98 Second Edition CD enter g WIN98_se where g is the driver letter of the CD ROM drive for Copy files from and click OK The dialog shown at right will be dis played Click Finish This completes installation of the de vice drivers You can now perform the Windows 98 SE update as described on page 17 Update Device Driver Wizard Windows has found an updated driver for this device and also some other drivers that should work with this device zd Host Controller C One of the other drivers Add New Hardware Wizard Windows driver file search for the d
123. settings will take effect Do you want to restart your computer now Open Explore My Cg Search Map Network Drive Disconnect Network Drive Create Shortcut Rename General Device Manager Hardware Profiles Performance View devices by type View devices by connection 1394 Bus Controller a9 NEC Firewarden OHCI Compliant IEEE 1394 Host Control H E Disk drives 4 a Display adapters H 3 Floppy disk controllers H 6 Hard disk controllers H E Keyboard I Modem H Monitors gt Mouse Network adapters H PCMCIA socket D ey z b Properties Refresh Remove Print 13 E Windows 98 Second Edition SE 1 The first time the computer is pow ered on with the board in place the dialog shown at right will be dis played Click Next Select Search for the best driver for your device Recommended and click Next The dialog shown at right will be dis played After making sure that none of the options are selected click Next 14 Add New Hardware Wizard This wizard searches for new drivers for NEG Firewarden OHCI Compliant IEEE 1394 Host Controller 4 device driver is a software program that makes a hardware device work Add New Hardware Wizard What do you want Windows to do peeeeenneneeeensansceseesnesssenssenensanseneesssensenanssessssassannsssanssnnesessannensensenney Evecensssssenensssnenssnsssensnsnssnnssnensssersn
124. shooter Device usage Use this device enable bal aq 0007 41 4000 ED Updating the Device Driver Windows 2000 Professional If the scanner Is not listed under Imaging devices in the Device Manager or the message This device is working properly does not appear in the Properties dialog you will need to reinstall the device driver as detailed below 1 5 42 Open the scanner Properties dialog Display the Device Manager as described in steps 1 3 of Confirming Device Registration Windows 2000 Professional on AO If the scanner is listed under Other devices or appears next to a or x double click the entry for the scanner to display the scanner Properties dialog Click Update Driver Open the Driver tab and click Update MACIN ENEE 2j xj Driver General Driver Nikon LS 4000ED IEEE 1394 SBP2 Device Driver Provider Unknown Driver Date Not available Driver Version Not available Digital Signer Not digitally signed No driver files are required or have been loaded for this device To uninstall the driver files for this device click Uninstall To update the driver files for this device click Update Driver Update Driver OK Cancel Click Next When the Upgrade Device Driver Wizard ZENNE is displayed click Next Welcome to the Upgrade Device Driver Wizard This wizard helps you upgrade a device driver for a hardwar
125. starts automati ja Install the software automatically Recommended Cd ly W h en yo u Inse rt th e N ko n Sca n C D 1 Install from a list or specific ate Advanced click Exit to close the Welcome window Click Next to continue 34 4 Select ls4000xp inf Select Is4000xp inf in the list of drivers EF an d cl ick Next Please select the best match for your hardware from the list below Is4000xp int If ls4000xp inf is not visible in the list drag the scroll bar at the right of the list until it is displayed F a Nikon SUPER COOLSCAN 4000 ED CAN 4000ED Unknown Nikon Corporation d inf ls4000 win98se ls4000se inf CAN 4000ED Unknown Nikon Corporation d infXls4000 win2000 Is40002k inf lt gt A This driver is not digitally signed Tell me why driver signing is important D Click Continue Click Continue Anyway to begin instal lation of the files need to register the scan ner The software you are installing for this hardware Nikon SUPER COOLSCAN 4000 ED Hardware Installation aq 0007 has not passed Windows Logo testing to verify its compatibility with Windows xP Tell me why this testing is important Continuing your installation of this software may impair or destabilize the corect operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows
126. stered with the system as described in Confirming Device Registration Windows 2000 Professional on 40 39 m Confirming Device Registration Windows 2000 Professional After registering the scanner confirm that the device is working normally as described below 4000 ED 1 2 40 Turn the scanner on Make sure that the scanner is connected and turned on Open the System Properties dialog From the Start menu select Settings gt Control Panel and double click the System ICON Display the Device Manager The System Properties dialog will be dis played Open the Hardware tab and click Device Manager System Properties E General Network Identification Hardware User Profiles Advanced 2x m Hardware Wizard The Hardware wizard helps you install uninstall repair unplug eject and configure pour hardware Hardware Wizard sass Device Manager The Device Manager lists all the hardware devices installed on your computer Use the Device Manager to change the properties of any device Device Manager Driver Signing Hardware Profiles Hardware profiles provide a way for you to set up and store different hardware configurations Hardware Profiles IR an amp 4 J Confirm that the scanner is listed under Imaging devices If Imaging devices appears in the De vice Manager click the to Its left to view the ima
127. sure that the Nikon Scan 3 plug in Nikon Scan Plugin 3 1 has been copied into the Import Export folder in the application s plug in folder You can then scan images into the application by selecting Nikon Scan from the application s list of Acquire or Import sources For more information see the documentation for the application in question 86 The Nikon Scan scan window will open on the desktop File Size 7 MB AnalogGain Neutral Digital ROC Neutral Digital GEM Neutral Digital ICE Off MultiS ample 1x Bit Depth 8 Scan window 2 Choose the film type Choose the type of film to be scanned from the media type menu Choose a color model Choose a color model from the color model menu The most common choice for images that will be edited on a computer is Calibrated RGB Choose Grayscale when scanning black and white monochrome film CMYK is intended for professionals who need to create a file ready for printing on an industrial four color printer F y SSettngs 7 L r l I MNeglColoor w all Cetting s Sbroclyve F alba 87 4 Click the Preview button Click the Preview button to create a preview of the image to be scanned Preview button The preview will be displayed in the preview area _ Settingos wv Postive F _albrated Hab w H File Size 67 27 MB AnalogGain Neutral Digital ROC Neutral Digital GEM
128. t Win dows has found the drivers for the device Click Next Update Device Driver Wizard 4000 ED Windows driver file search for the device Nikon LS 4000 ED Windows is now ready to install the best driver for this device Click Back to select a different driver or click Next to continue amp Location of driver o el m G AINFSLS4000 WINS8SE gt Click Finish Click Finish to complete installation Update Device EE E s Nikon LS 4000 ED Windows has finished installing the updated drivers for your hardware device 9 Confirm device registration Confirm that the scanner has been correctly registered with the system as described in Confirming Device Registration Windows 98 SE J 53 54 56 Registering the COOLSCAN IV ED with Windows Windows XP Home Edition Windows XP Professional Registering the Scanner with Windows XP 1 Turn the scanner on The first time the computer detects the scanner Windows will display the dialog shown at right 2 Insert the Nikon Scan 3 CD Holding down the shift key to prevent the Welcome program from starting auto matically insert the Nikon Scan 3 CD into the CD ROM drive The dialog shown at right will be displayed click Continue Anyway If the Dialog Is Not Displayed If the dialog shown at right is not displayed automatically select the automatic install option in the dialog shown in step 1 and click Next Logging On Found New Hardware Wiz
129. t dimensions of the image to fit it into a pre determined space for example in a magazine or on a web page Follow the directions above to select the output resolution and output units then enter the desired values for Width and Height in the output size text boxes The crop selected in the preview area will automatically be adjusted to maintain the crop at these proportions e Keep this file size Choose this option when you want to select the general area to be scanned using the mouse and then specify the exact file size of the final image for example to keep file sizes to a minimum for storage or electronic transfer or because you have been asked for a file of a certain size Enter a value for file size in the file size text box and select the units for file size from the menu to its right 94 1 0 Adjust color contrast and sharpness ooocopg Curves The Curves palette makes it possible to adjust color balance and contrast in specific por tions of the tone range For example you can selectively enhance detail in dark portions of the image shadow brighten mid tones or bring out details in highlights Changes can be made to all the component colors in the image or only to specific color components channels Color Balance The Color Balance palette can be used to adjust brightness contrast and color balance over the entire tone range LCH Editor The LCH Editor is used to adjust brightness and contrast in specific portions
130. t infants from putting small parts of the equipment into their mouths In the event that a child should swallow part of the equipment contact a physician immediately Do not handle the power cable during thunderstorms Operating the equipment during thunderstorms could result in electric shock Do not go near the equipment or handle the power cable until after the thunderstorm has passed Do not play CD ROM disks on audio CD players The CDs provided with this product should not be played back on audio CD equipment Playing CD ROMs on an audio CD player could cause hearing loss or damage the equipment Use an appropriate power supply Use an AC power supply of 50 60Hz and a voltage of from 100V 240V Use a power cord rated for the appropriate voltage At voltages of over AC 125V Use a power cord that complies with the safety standards of the country in which it is used that has a plug rated for AC 250V 15A NEMA 6P 15 and insulation of SVT type or better and that is more than AWG18 in thickness At voltages of AC 125V or less Use a power cord that complies with the safety standards of the country in which it is used that has a plug rated for AC 125V 10A and insulation of SVT type or better and that is more than AWG18 in thickness Observe appropriate precautions when handling the power cable Do not damage or modify the power cable Fire or electric shock could result if the cable is placed under heavy objects exposed to heat or flame
131. t the most from your scanner please read the documentation provided 118 D Follow the on screen instructions to complete installation Acrobat Reader 4 0 Setup Welcome to the Acrobat Reader 4 0 Setup program This program will install Acrobat Reader 4 0 on your d computer It is strongly recommended that you exit all Windows programs before running this Setup program Click Cancel to quit Setup and then close any programs you have running Click Next to continue with the Setup program WARNING This program is protected by copyright law and international treaties Unauthorized reproduction or distribution of this program or any Acrobat Re ader 4 0 portion of it may result in severe civil and criminal penalties and e will be prosecuted to the maximum extent possible under law Cancel This installation was created with Installer VISE from Mind ision Software Windows Macintosh Once installation is complete you will be able to view the Nikon Scan Software Manual by double clicking the INDEX pdf icon in the root directory of the reference CD and choosing a language from the menu that appears NIKON 0 File Edit View Favorites Tools Help ac gt S PP Search Folders E Address 3 0 1 File and Folder Tasks Deutsch Deutsch English K Publish this folder to the Web j E3 Share this folder Espa ol Fran ais g Other Places 7 y i Ga Italiano
132. temperature m it would be exposed to dust or smoke m it would be exposed to water vapor from a humidifier Vj it would be exposed to radio interference from other electronic devices vy the temperature exceeds 35 C 95 F or falls below 10 C 50 F 0 other objects would block the scanner s vents The scanner has feet on two sides allowing it to be installed in either of the orientations shown below Leave enough space around the scanner to ensure ease of operation at least 5 cm 2 above and on either side of the scanner and 10 cm 4 behind it When using the SA 21 strip film adapter the front of the scanner should be at least 15 cm 67 from the edge of the surface on which the scanner is placed to prevent film from falling to the floor when ejected from the adapter s film slot If you are using the FH 3 film holder leave at least 25 cm 9 8 free in front of the scanner 15cm 6 Protect Your Film The Digital ICE photo retouch function built into your Nikon scanner can be used to eliminate the effects of dust scratches and surface defects on your film To ensure the best possible results and to prevent damage to slides or film however be sure to protect your film trom dust fingerprints and condensation as described below y Fingerprints can be removed with a soft dry cloth Be careful not to scratch the surface of the film when removing fingerprints m Remove dust from the film with a blower T
133. ter slot as this could result in damage to any film that may be protruding from the rear of the adapter 134 Removing Film 1 After placing the adapter on a table or other flat stable surface press the release button on top of the adapter open the front panel and open and remove the upper cover Release button Upper cover Front panel e fthe end of the film strip is not visible rotate the toothed wheel until the end of the film protrudes from either end of the adapter v Place the adapter on a table or other flat stable surface before opening the cover If you hold the adapter in your hand while removing the upper cover the adapter could fall to the floor and be damaged 135 n 2 Release the frame lock lever and open the roller frame Roller frame Frame lock lever 3 Pull gently on the film to remove it from the film slot or from the rear of the adapter Frame lock lever 4 After removing the film follow the steps above in reverse order to close and lock the roller frame and return the upper cover to its place before closing the front cover m The roller frame should not be removed from the adapter When opening the roller frame stop when you feel resistance Forcing the frame open could result in damage to the adapter Work with the adapter and scanner on a table or other flat stable surface The adapter or scanner could be damaged should either fall to the floor 136 Mainten
134. th other IEEE 1394 devices disconnect all IEEE 1394 devices including the scanner and then re connect the scanner m Only one scanner can be connected to the computer at a time Using the COOLSCAN IV ED with Other Devices When using the COOLSCAN IV ED with other devices connected to the same USB port m Do not turn other devices on or off or disconnect interface cables while scanning is in progress i e while the scanner status LED is blinking slowly m Connect the scanner directly to the computer The scanner may not function as expected when connected to a USB hub The scanner may not function as expected when operated at the same time as other USB devices Should a problem occur when the scanner is used with other USB devices disconnect all USB devices including the scanner and then reconnect the scanner vy Only one scanner can be connected to the computer at a time Connecting the Scanner Although this manual instructs the user to turn the scanner off before connecting the interface cable IEEE 1394 cables can be connected while the scanner and computer are on and the scanner used immediately following connection There is consequently no need to turn the scanner off every time the cable is connected or disconnected You should however leave a few seconds between disconnecting and recon necting the cable 8 Installing the IEEE 1394 Firewire Interface Board 4000 ED Only _ If your computer is not alrea
135. tion Unplug the equipment immediately should you notice anything out of the ordinary e Should you notice an unusual noise smell or smoke coming from the equipment turn the scanner off at once and unplug the power cable Continued use could cause fire or electric shock After ensuring that the equip ment is no longer smoking contact your dealer or Nikon service representative for information on replacement or repair Do not attempt repairs yourself as this would be extremely dangerous In the event of damage to the equipment turn the scanner off at once and unplug the power cable then contact your dealer or Nikon service representative for information on replacement or repair Continued use could result in fire or electric shock Do not allow foreign objects to enter the scanner e Do not place vases flowerpots cups cosmetics vessels containing chemicals or water or small metal articles on top of the equipment Should such articles or their contents fall into the equipment fire electric shock or malfunction could result In the event that foreign substances or water should find their way into the equipment turn the scanner off immediately unplug the power cord and contact your dealer or nearest Nikon service representative Continued use could result in fire electric shock or malfunction Particular care is advised in households with small children Keep small objects out of reach of children Particular care should be taken to preven
136. tton File view Nikon Scan Window Help Imagel 6 ER Windows Macintosh Once you have saved the scanned image you can open it for editing in another application such as Photoshop Image Windows You can close the scan window if it blocks your view of the image in the image window 97 12 Scan additional images To scan additional images after closing the scan window select the scanner from the Nikon Scan gt Tools menu In Windows you can also open the scan window by selecting Open TWAIN Source from the File menu If you are using Nikon Scan to scan images directly into another application open the scan window by selecting Nikon Scan from the application s list of Acquire or Import sources You can then repeat steps 2 to 11 to scan additional images 1 3 Exit Nikon Scan and turn the scanner off 13 1 Remove the slide Press the eject button on the front of the MA 20 S to partially eject the slide You can then remove the slide by hand 98 13 2 Remove the film adapter Slide the film adapter from the adapter slot 13 3 Close the sliding cover Slide the cover closed 13 4 Exit Nikon Scan If you are using Nikon Scan as a stand alone application choose Exit Windows or Quit Macintosh from the File menu to exit Nikon Scan If you are using Nikon Scan to scan images directly into another application simply close the scan window by clicking the close box 99 i 100
137. tus LED to stop blinking and then turn the scanner off by pressing the power button If you are using Windows Me or Windows 98 SE you must first remove the scanner trom the system as described below Windows Me Shut down the computer Once the computer has turned off press the power button to turn the scanner off Windows 98 SE Click the Unplug or Eject Hardware button Stop Nikon SUPER COOLS in the taskbar and select Stop Nikon SUPER COOLSCAN 4000 ED from the menu that ap pears A message will be displayed stating that the scanner can be safely removed trom the system click OK and follow the on screen instructions to terminate the trans ter of data between the scanner and the computer You can then turn the scanner off by pressing the power button If you fail to perform this step before dis connecting the Scanner or tu rning it off 3 You have unplugged or ejected a device without stopping it which can cause your computer to crash and lose valuable data the dialog shown at right will be displayed N Please use the hotplug icon in the status bar to safely stop devices before unplugging them Nikon Scan This chapter provides a brief overview of Nikon Scan the software that drives your Nikon scanner For more information see the Nikon Scan 3 Software Manual available in pdt format on the Nikon Software Manual CD provided with your scanner Viewing the Nikon Scan 3 Software Manual 118 tne Sc
138. und a driver for this device To install the driver Windows found click Next 3 HL k NinfMls4000 win2000 ls40002k inf lt Back a Cancel Q Click Yes The dialog shown at right will be displayed ENEN x Click Yes The Microsoft digital signature affirms that software has been tested with Windows and that the software has not been altered since it was tested The software you are about to install does not contain a Microsoft digital signature Therefore there is no guarantee that this software works correctly with windows Nikon SUPER COOLSCAN 4000 ED If you want to search for Microsoft digitally signed software visit the Windows Update Web site at http windowsupdate microsoft com to see if one is available Do you want to continue the installation Yes No More Info 38 The dialog shown at right will be displayec EMN while Windows registers the scanner Haase In Windows is installing drivers for your new hardware Nikon LS 4000 ED a Installing software necessary to support your hardware o Click Finish Click Finish to complete installation Completing the Found New Hardware Wizard gt Nikon SUPER COOLSCAN 4000 ED aq 0007 Windows has finished installing the software for this device To close this wizard click Finish 10 Restart the computer Click Yes to restart the computer 11 Confirm device registration Confirm that the scanner has been correctly regi
139. unmounted 35 mm film Strip film can be scanned using the SA 21 strip film adapter or by placing film in the FH 3 film holder and inserting it in MA 20 S slide mount adapter Film That Can Not Be Scanned in the SA 21 102 DSi MOGi Medel 3a aea a erscee treme A 105 Using tess Aw Iena a a a a a cee 111 101 Ea Film That Can Not Be Scanned in the SA 21 Film That Can Not Be Used The following film can not be scanned in the SA 21 Use the FH 3 film holder with the MA 20 S slide mount adapter Film strip is only one frame long Perforations Perforations MOE OOE gt R Use the FH 3 film holder with the MA 20 S slide mount adapter Perforations are torn or missing Use the FH 3 film holder with the MA 20 S slide Less jean mount adapter 6 mm or more 30 mm N Film has excessive curl Using scissors cut the film into lengths of two to See pone six frames before scanning or scan the film using We pee Or eee ae are the optional SA 30 roll film adapter 4000 ED only Sy Pg For more information on 105 _ Using the FH 3 143 Optional accessories 102 Film That Must Be Repaired Before Use Film with the defects listed below must be repaired before it can be scanned in the SA 21 It can be scanned without preparation using the FH 3 film holder with the MA 20 S slide mount adapter J 105 ee ET
140. ver s Nikon COOLSCAN IV ED Driver Provider Nikon Corporation Driver Date 11 01 2000 Digital Signer Not signed To view details about the driver files loaded for this device click Driver File Details To update the driver files for this device click Update Driver 3 Insert the Nikon Scan 3 CD The Upgrade Device Driver Wizard will be MAXIE displayed Holding down the shift key to prevent the Welcome program from start ing automatically insert the Nikon Scan 3 CD into the CD ROM drive The Welcome Window l If the Welcome program starts automati Automatic search for a better diver Recommended cally when you insert the Nikon Scan CD click Exit to close the Welcome window This wizard searches for updated drivers for Nikon COOLSCAN IV ED Windows can search for and install an updated driver to replace the one currently being used by your hardware Or you can specify the location of another driver What would you like to do 74 4 Select the search option F Select the search option and click Next Update Device Driver Wizard This wizard searches for updated drivers for Nikon COOLSCAN IV ED Windows can search for and install an updated driver to replace the one currently being used by your hardware Or you can specify the location of another driver What would you like to do Specify the location of the driver Advanced lt Back E Cancel
141. vice Driver Windows XP If the scanner Is not listed under Imaging devices in the Device Manager or the message This device is working properly does not appear in the Properties dialog you will need to reinstall the device driver as detailed below 1 Open the scanner Properties dialog Display the Device Manager as described in steps 1 3 of Confirming Device Registration Windows XP on 32 If the scanner is listed under Other devices or appears next to a l 2 or x double click the entry for the scanner to display the scanner Properties dialog 2 Click Reinstall Driver Open the General tab and click Reinstall PPA EEA A Driver General Driver a Nikon LS 4000ED IEEE 1394 SBP2 Device Device type Imaging devices Manufacturer Unknown Location LUN 0 Device status This device is not configured correctly Code 1 To reinstall the drivers for this device click Reinstall Driver Reinstall Driver Device usage Use this device enable v Insert the Nikon Scan 3 CD The dialog shown at right will be displayed 05S Holding down the shift key to prevent the W l onie ane Hardware Update Welcome program from starting automati wizard cally insert the Nikon Scan 3 CD into the Ee ee CD ROM drive Select the automatic in a Stall option and click Next The Welcome Window If your hardware came with an installation CD ZE or floppy disk insert it now If the Welcome program
142. y the Device Manager as described in steps 1 3 of Confirming Device Registration Windows XP on 59 If the scanner is listed under Other devices or appears next to a 1 2 or x double click the entry for the scanner to display the scanner Properties dialog 2 Click Reinstall driver Open the General tab and click Reinstall GAMA driver General Driver a LS 40 ED Device type Imaging devices Manufacturer Unknown Location LS 40 ED Device status This device is not configured correctly Code 1 To reinstall the drivers for this device click Reinstall Driver di Al N O O N AO gt Reinstall Driver Device usage Use this device enable v 3 Insert the Nikon Scan 3 CD a i Hardware Update Wizard The dialog shown at right will be displayed gaan Welcome to the Hardware Update Holding down the shift key to prevent the BS on Welcome prog ram from starting automati BS This wizard helps you install software for cally insert the Nikon Scan 3 CD into the LS 40ED CD ROM drive Select the automatic in stall option and click Next E o M Li reedi egei lem ee The Welcome Win dow What do you want the wizard to do If the Welcome program Sta rts automati Install the Sae automiabicaly Mecomimanded cally when you insert the Nikon Scan CD Install from a list or specific location Advanced click Exit to close the Welcome window Click Next to continue 61 C
143. you insert the Nikon Scan CD click Exit to close the 9 enn Welcome window GR Nikon Scan 3 e ede n T hitp www Niken Asia com hitp www Nikon Euro com hiip www Nikon USA com 4000 ED 52 Select the Win98SE folder The Browse for Folder dialog will be dis played Select the Win98SE folder un der Nkscan gt INF gt Ls4000 and click OK Confirm the file path The dialog shown at right will be displayed Confirm that the path INALS4000 Win98SE appears after the drive letter of the CD ROM drive and click Next If the Correct Path Is Not Displayed If the correct path is not displayed repeat steps 4 6 to select the correct path Begin installation of the device drivers Click Next Click Finish Click Finish to complete installation Confirm device registration Confirm that the scanner has been cor rectly registered with the system as de scribed in Confirming Device Registration Windows 98 SE R 53 OTOWSe fOr FOMer r Hi Eas Select the folder that contains driver information IMF tile for thi device ey F 1 peg Nkscan G 2 BA Firmware I INF EY Leoa oof Win2000 S in385E a Microsoft LS Nkscan E HA x Cancel Add New Hardware Wizard Windows will search for new drivers in its driver database on your hard drive and in any of the following selected locations Click Next to start the search T F

Nikon COOLSCAN IV ED LS40

Contents

Download Pdf Manuals

Related Search

Related Contents