Xerox 510DP All in One Printer User Manual
Contents
1. Replacing the toner waste bottle Each time you replace the toner cartridge you must replace the toner waste bottle as well To replace the toner waste bottle 1 Open the front door WIDE FORMAT 510dp OPERATOR MANUAL 31 CARE CAUTION Pull the toner waste bottle out gently to avoid spillage of toner 2 Carefully remove the toner waste bottle e Pull the waste bottle forward until it disengages from the mounting bracket 3 Remove the stopper from the side of the used toner waste bottle 32 XEROX WIDE FORMAT 510dp OPERATOR MANUAL XEROX WIDE FORMAT 5109 OPERATOR MANUAL CARE CAUTION Ensure that the stopper is firmly in place to avoid spillage of toner 4 Snap the stopper into place on the top of the used toner waste bottle Remove the stopper from the top of the new toner waste bottle Snap the stopper into place on the front of the new toner waste bottle Slide the new toner waste bottle onto the mounting bracket e Push the bottle forward until you feel it snap into place Close the front door CAUTION Do not reuse the contents of the toner waste bottle Reuse of this material will damage the printer 9 Place the used toner waste bottle in the plastic bag provided in the replacement carton 10 Place the used toner waste bottle in the replacement toner carton e Ensure that the carton contains the used toner cartridge as well Recycle the used2. e To select the READY TO POWER SAVER option press the Enter key e To select the POWER SAVER TO REST option Navigate to it by pressing the Previous or Next key Press the Enter key to select the option 5 Press the Previous or Next key to scroll through the range of values 6 When you scroll to the desired value press the Enter key to save your selection 7 Press the On line Off line key to return to on line mode e The on line off line indicator will light e display will indicate SYNERGIX CS 510dp IDLE or SYNERGIX PS 510 Note If there is a Scanner connected the message displayed will be SYNERGIX CS 510dp If there is no Scanner connected the message will be SYNERGIX PS 510dp To adjust the print density 1 Access the PRINTER MENU See Accessing the Printer Menu in this chapter 2 Press the Previous or Next key until PRINTER ADJUSTMENTS is displayed 3 Press the Enter key to select PRINTER ADJUSTMENTS The current setting for the DENSITY option is displayed 4 Press the Enter key to select DENSITY Press the Previous or Next key to scroll through the range of values 6 When you scroll to the desired value press the Enter key to save your selection 7 Press the On line Off line key to return to on line mode e The on line off line indicator will light e The display will indicate SYNERGIX CS 510dp IDLE or SYNERGIX PS 510dp 23 OFF LINE SETUP MENU Specifying the
3. OPERATOR MANUAL MEDIA Press the Previous or Next key to scroll through the media type selections The media type selections are BOND VELLUM and FILM When you scroll to the desired media type press the Enter key Do one of the following Press the Media key or the Exit key in order to save your selections and return to the system prompt Press the Enter key to return to the media size and type selection process and change the selections you just made 15 MEDIA Using the cut sheet feed in shelf When the correct media size or type is not loaded in the printer you can bypass the media drawers and manually load cut sheets into the printer If large size cut sheet prints portrait D size 1 oe E size 0 are being made return to the Printer and guide the lead edge of the print as it exits the Printer to prevent the print from jamming at the exit With the Output Tray in the raised position the prints could feed back into the Printer To manually feed cut sheets into the printer Raise the output tray all the way until it rests on top of the printer Select the appropriate cut sheet for the print job NOTE The minimum size for a cut sheet is 8 1 2 x 11 inches 216 x 279 mm fed short edge lead Set the BYPASS media type on the printer control panel to the correct one for the print job See Changing the roll media size and type for further information NOTE The printer will accept whate
4. Note If there is a Scanner connected the message displayed will be SYNERGIX CS 510dp If there is no Scanner connected the message will be SYNERGIX PS 510dp To enable or disable the Audible Indicators 1 Access the PRINTER MENU See Accessing the Printer Menu in this chapter 2 Press the Enter key to select AUDIBLE INDICATORS The current setting for the KEYPRESS option is displayed 3 Do one of the following e To select the KEYPRESS option press the Enter key select the ALARM option Navigate to it by pressing the Previous or Next key The current setting for the ALARM option is displayed Press the Enter key to select the option 4 Press the Previous or Next key to switch between ON and OFF Press the Enter key to save your selection Press the On line Off line key to return to on line mode e The on line off line indicator will light e display will indicate SYNERGIX CS 510dp IDLE or SYNERGIX PS 510 XEROX WIDE FORMAT 510dp OPERATOR MANUAL Setting the timers Adjusting the print density XEROX WIDE FORMAT 510dp OPERATOR MANUAL OFF LINE SETUP MENU To set the Power Saver mode and Rest mode timers 1 Access the PRINTER MENU See Accessing the Printer Menu in this chapter Press the Previous or Next key until TIMERS is displayed Press the Enter key to select TIMERS The current setting for the READY TO POWER SAVER option is displayed 4 Do of the following
5. ROLL 1 ROLL 2 ROLL 3 and BYPASS PRINTER DIAGNOSTICS Reserved for use by the service representative and is password protected RECENT FAULT LOG Displays a record of the last 99 printer faults You may be asked to provide information from this log when placing a call for service BILLING METERS METER A Provides a record of the total number of square feet meters of prints produced This number is useful for both billing and service purposes METER B Provides a record of the total number of linear feet meters of prints produced This number is useful for both billing and service purposes XEROX WIDE FORMAT 510dp OPERATOR MANUAL 21 OFF LINE SETUP MENU Accessing the Printer Menu Note If there is a Scanner connected the message displayed will be SYNERGIX CS 510dp If there is no Scanner connected the message will be SYNERGIX PS 510dp To access the Printer Menu 1 Press the On line Off line key to enter off line mode e The on line off line indicator will go out The display will indicate SYNERGIX CS 510dp PAUSED or SYNERGIX PS 510dp 2 Press the Enter key to access the SYNERGIX CS 510 or SYNERGIX PS 510dp SETUP MENU 3 Press the Previous or Next key until PRINTER MENU is displayed 4 Press the Enter key to access the PRINTER MENU e The display will indicate PRINTER MENU lt AUDIBLE INDICATORS gt This is the first PRINTER MENU option Enabling or disabling the audible indicators 22
6. 2 Open the fuser drawer all the way 3 Do one of the following e Pull the jammed media out the back of the fuser area Go to step 7 e f you cannot pull the jammed media out of the fuser area go to step 4 38 XEROX WIDE FORMAT 510dp OPERATOR MANUAL XEROX WIDE FORMAT 5109 OPERATOR MANUAL PROBLEM SOLVING 4 Lift the inside latches on each side of the fuser drawer front and lower the fuser drawer front 5 Hold the drawer front all the way open and pull the jammed media out of the back of the fuser area 6 Close the fuser drawer front Ensure that it latches T Close the fuser drawer 39 PROBLEM SOLVING Cutter area jam To clear a jam in the cutter area WARNING The cutter blade is very sharp Do not touch the cutter blade when clearing media jams in the cutter area 1 Squeeze the latches on the cut sheet feed in drawer and open the drawer all the way 2 Pull the media out of the cutter area 3 Close the cutter drawer 40 XEROX WIDE FORMAT 510dp OPERATOR MANUAL PROBLEM SOLVING Roll media drawer jams To clear a jam in a roll media drawer 1 Raise the output tray all the way so that it rests on top of the printer 2 Lift the handle of the applicable drawer and open the drawer all the way NOTE some locations high or low humidity affects the media and causes print quality problems To resolve the problems a sealed media drawer can be installed on the printer i
7. OPERATOR MANUAL Media specifications Media type Media supply Media size Print size TECHNICAL DATA Table 8 Media Specifications Recommended media types Bond 20 to 24 80 to 90 gsm xerographic roll paper or cut sheets Vellum tracing 20 80 gsm Film 4 millimeter thickness double matte heat stable 3 rolls 500 feet 152 meters each Standard manual bypass for cut sheets Roll feed Width 11 to 36 inches 279 to 914 Core diameter 3 to 6 7 inches 76 to 170 mm Manual cut sheet feed Width 11 to 36 inches 279 to 914 mm Minimum length 8 1 2 inches 216 mm Minimum Manual cut sheet feed portrait 8 1 2 x 11 inches 216 x 279 mm Roll feed landscape 11 x 8 1 2 inches 279 x 216 mm Maximum Manual cut sheet feed 36 x 48 inches 914 x 1219 mm Roll feed 36 inches x 80 feet 914 mm x 24 meters XEROX WIDE FORMAT 510dp OPERATOR MANUAL 51 TECHNICAL DATA Space requirements The illustration below shows the space requirements for normal operation of the printer after installation The height clearance from the floor to the nearest overhead obstruction within the floor space requirement is 78 inches 1981 mm 24 610 mm 36 914 mm 36 914 mm 83 2108 mm 36 914 mm M _ _ 129 3277 NOTE Once installed this machine is not considered movable If moved re leveling of the machine will be required 52
8. XEROX WIDE FORMAT 510dp OPERATOR MANUAL
9. may have and if necessary arrange for a customer service engineer to service your equipment Be prepared to provide the following information to the customer service representative e Customer account number e Machine type XEROX Wide Format 510dp e Machine serial number NOTE The serial number is located behind the front door as shown in the illustration below Serial number Adescription of the problem e f applicable the status code and message that appear on the message display Be sure to note the location of any flashing indicator lights as well For more information visit the Xerox Engineering Systems web site at www xes com XEROX WIDE FORMAT 510dp OPERATOR MANUAL 47 PROBLEM SOLVING This page has been intentionally left blank 48 XEROX WIDE FORMAT 510dp OPERATOR MANUAL 7 Technical data This chapter provides the product and media specifications for the XEROX Wide Format 510dp It also provides the space requirements for normal operation after product installation Product specifications Table 5 Hardware Specifications Environmental requirements Minimum 60 F 10 C at 20 relative humidity Maximum 80 F 27 C at 80 relative humidity Maximum elevation 10 000 feet 3048 meters Weight 575 lbs 261 kg Dimensions Width As delivered 23 inches 584 mm With output tray and AccXES controller installed 62 inches 1575 mm Depth 57 inches 1448 mm Height 42 5 inches 1080
10. previous selection or to return to the next higher menu level If you have modified a parameter the parameter will remain unchanged XEROX Wide Format 510dp OPERATOR MANUAL 8 On line Off line key 9 Numeric keypad 10 Language key XEROX WIDE FORMAT 510dp OPERATOR MANUAL PRINTER OVERVIEW Press this key to switch between the on line and off line modes In on line mode the indicator light to the left of the key is lit In off line mode the indicator light is not lit When in on line mode the printer accepts and processes print requests When in off line mode the printer holds print requests in the print queue The requests remain in the print queue until either the printer returns to on line mode or power to the controller is lost From off line mode you can access the Setup Menu The Setup Menu allows you to perform a variety of utilities and diagnostics NOTE The Media key is functional from both on line and off line modes The power saver and rest functions apply to on line mode only This keypad contains digits O to 9 a period and a clear key The numeric keys are used for selecting menus and inputting values The period is used for entering a decimal point The clear key is used to clear the contents of an entry Press this key to switch between the primary and secondary language for the message display If no secondary language has been installed pressing this key causes no action PRINTER OVERVIEW This pag
11. section of this manual 42 02 This code indicates that the toner cartridge is not installed correctly Refer to the Replacing the toner cartridge section of this manual Switch the printer off Wait several seconds Then switch the printer on 44 XEROX WIDE FORMAT 510dp OPERATOR MANUAL PROBLEM SOLVING Error messages The error messages shown in the table below may appear on the message display Follow the instructions in the table before calling for service Table 3 Error Message Table CHECK FOLDER FINISHER CONFIG TYPE Press the On line Off line key to FOLDER COMMUNICATIONS ERROR enabled but no folder is take the printer off line 17 installed Reset the value to NONE Refer to Specifying the finisher configuration type in this manual for instructions F2 01 CHECK FOLDER FINISHER CONFIG TYPE Switch the printer Off FOLDER COMMUNICATOINS ERROR enabled but no folder is Wait five seconds Then switch the printer On 01 installed As soon as the Printer Firmware Version message is displayed press the On line Offline key to take the printer off line Reset the value to NONE Refer to Specifying the finisher configuration type in this manual for instructions XEROX WIDE FORMAT 510dp OPERATOR MANUAL 45 PROBLEM SOLVING Problem solving table The table below lists some conditions that may occur during the operation of the printer You may be able to resolve the problems by following the suggeste
12. shock Never spill liquid of any kind on the units Never remove any covers or guards that require a tool for removal There are no operator serviceable areas within these covers Never attempt any maintenance function that is not specified in this operator guide Never defeat interlock switches Machines are designed to prevent operator access to unsafe areas Covers guards and interlock switches are provided to ensure that the system will not operate with the covers opened Unplug the reprographic system from the wall outlet and refer servicing to a qualified service individual under the following conditions e When the power cord is damaged or frayed If liquid has been spilled into the product e Ifthe units have been exposed to rain or water e units are producing unusual noises or odors e ftheunits or the cabinets have been damaged If you need additional safety information concerning the printer or XEROX supply materials you may call Within the United States 1 800 828 6571 toll free In other countries Please call your local Xerox Engineering Systems service office for help XEROX WIDE FORMAT 510ddp OPERATOR MANUAL Introduction Congratulations on acquiring your new XEROX Wide Format 510dp Xerox looks forward to supporting you and helping you increases your printing productivity XEROX Wide Format 510dp is available as a standalone printer with AccXES controller or as a multifuncti
13. text string refer to selections on the control panel for example press the Enter key A WARNING indicates an operation maintenance procedure practice condition or statement that if not strictly followed could result in personal injury When included within a procedure warnings always precede the step to which they refer A CAUTION encourages strict compliance with an operation maintenance procedure practice condition or statement to prevent damage to the equipment When included within a procedure cautions always precede the step to which they refer A NOTE highlights an operating or maintenance procedure a condition or a statement XEROX WIDE FORMAT 510ddp OPERATOR MANUAL 1 Printer overview This chapter shows the orientation of the printer It also illustrates and describes its main components as well as the elements of the control panel Printer orientation The illustration below shows the printer orientation You must be familiar with this orientation when following the messages in the message display and the instructions in this guide Left side Back Right side Front 1 2 3 4 XEROX WIDE FORMAT 510dp OPERATOR MANUAL 1 PRINTER OVERVIEW Main components gr de cm Output tray Drawer 1 Drawer 2 Drawer 3 Cut sheet feed in shelf Fuser drawer Front door Control panel Prints exit the printer face up onto this tray This tray holds up to 100 prints of all sizes inc
14. 37 Euserarea jam 5s die trn tet eder e m Deae ed tete E E Ao E ri Hes 38 Cutter area Jalm uii ete Re eedem infe Len n tue RR 40 XEROX WIDE FORMAT 510DP OPERATOR MANUAL i TABLE OF CONTENTS a 41 IEEE 44 Emor messages Rs 45 Problem solving table A e A e e oes 46 ier nemi Lm 47 icis LE 49 Product SpecifICations ie old iub t elite end 49 Media SDecifICatiOns c ice pen ol epe i o en M M i etg eite eI MU 51 Space requirements 52 XEROX WIDE FORMAT 510dDPOPERATOR MANUAL notices Australia New Zealand Changes or modifications to this equipment not specifically approved by Fuji Xerox Australia PTA Limited may void the user s authority to operate this equipment Shielded cables must be used with this equipment to maintain compliance with the Radiocommunications Act 1992 European Union WARNING This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Changes or modifications to this equipment not specifically approved by Xerox Europe may void the user s authority to operate this equipme
15. Ensure that the tube falls into place within the support rollers 14 Remove the tape from the lead edge of the media roll 15 If the lead edge of the media roll contains debris from the adhesive or is torn or uneven trim the lead edge NOTE Trimming is not usually necessary for a new roll of media 12 XEROX WIDE FORMAT 510dp OPERATOR MANUAL MEDIA 16 Rotate the media roll to feed the media under the baffle and beyond the registration window NOTE Ensure that the lead edge of the media is flat and is not folded over itself 17 Squeeze the baffle release and lower the baffle until it locks in place on both sides 18 Slowly rotate the media roll until the lead edge of the media is centered in the registration window 19 Do one of the following e fthe drawer is a sealed media drawer close the Plexiglas e If the drawer is not a sealed media drawer proceed to step 20 20 Close the roll media drawer 21 Lower the output tray 22 If the size or type of the new media roll is different from that of the old media roll you must specify the new size and type Refer to Changing the roll media size and type in this chapter for instructions on entering the new roll media information XEROX WIDE FORMAT 510dp OPERATOR MANUAL 13 MEDIA Changing the roll media size and type Whenever you open a media drawer the message display prompts you to change the type or width of the media If you h
16. FORMAT 5109 OPERATOR MANUAL 10 11 CARE Carefully lift the used toner cartridge out of the printer e Try not to tilt the cartridge too much to avoid toner spillage Wipe any excess toner off the used toner cartridge Seal the used toner cartridge dispenser patch with tape Place the used toner cartridge in the empty replacement toner carton not seal the carton until you have added the toner waste bottle to it as well Recycle the used cartridge and waste bottle according to the instructions provided with the replacement carton Hold the new toner cartridge horizontally and shake it side to side 10 or 12 times Install the new toner cartridge so that the end containing the cover tape is toward the front of the printer e Ensure that the cover tape is facing up 29 12 Lower the toner cartridge into position while pushing the plunger to the left 13 Release the plunger 14 Rotate the toner cartridge back and forth until the cartridge locks into position CAUTION Remove the cover tape carefully Do not remove the clear perforated seal 15 Remove the cover tape from the toner cartridge e not remove the seal under the tape 16 Slide the gold cartridge dispenser patch cover to the right to conceal the cartridge patch e Ensure that the cartridge patch is completely covered 17 Close the toner supply access cover 30 XEROX WIDE FORMAT 510dp OPERATOR MANUAL
17. Menu in this chapter 2 Press the Previous or Next key until DIAGNOSTICS is displayed Press the Enter key to select DIAGNOSTICS Press the Enter key to select TEST PLOT Press the Previous or Next key to scroll through the media sources 6 Press the Enter key to select the media source The printer will initialize the media supply and print the test plot 7 Press the On line Off line key to return to on line mode e The on line off line indicator will light XEROX WIDE FORMAT 510dp OPERATOR MANUAL Displaying the billing meter counts XEROX WIDE FORMAT 510dp OPERATOR MANUAL OFF LINE SETUP MENU e The display will indicate SYNERGIX CS 510dp IDLE or SYNERGIX PS 510 Viewing the recent fault log Note If there is a Scanner connected the message displayed will be SYNERGIX CS 510dp If there is no Scanner connected the message will be SYNERGIX PS 510dp To view the recent fault 1 Access the PRINTER MENU See Accessing the Printer Menu in this chapter 2 Press the Previous or Next key until DIAGNOSTICS is displayed Press the Enter key to select DIAGNOSTICS Press the Previous or Next key until RECENT FAULT LOG is displayed Press the Enter key to select RECENT FAULT LOG Press the Next key to display the two most recent faults Press the Previous or Next key to scroll through the fault listing 8 When you are finished viewing the fault listing press the On line Off line key to return to on line m
18. THE DOCUMENT COMPANY XEROX Xerox Wide Format 510DP Operator Manual 701P38535 Januar 2003 Prepared by Xerox Corporation Global Knowledge amp Language Services 800 Phillips Road Building 845 17S Webster New York 14580 9791 USA OXEROX Inc 2001 All rights reserved Printed in the United States of America XEROX Wide Format 510dp XES Synergix 8850 Digital Solution Synergix Scan System the digital box icon AccXES and acronym XEROX are trademarks of XEROX CORPORATION 701P38535 01 2002 Table of contents emere EM iii Australia New Zealand iiti uberi tete ette t deter aed acit latis do e te diluere decla tee ini iii Euro pean Uniofi i oet be iei Losada iii nC iii RO USA AE A AA IA RI AA Safety MOLES erige ia vii Organization and content of this vii Terminology used in this viii Conventions used in this viii 1 Printer OVerVIQwW oreet trien rennen ence Ud Lu alea a de ra 1 Pinter One tation tse osea occae aei uide nemo M redo o Meiner d
19. ains six options The table below describes the Printer Menu options and their sub options Table 1 Printer Menu options AUDIBLE INDICATORS KEYPRESS Enables or disables an audible beeper when a control panel key is pressed Settings and OFF Default ON Enables or disables an audible beeper when the printer experiences a condition requiring immediate attention Settings ON and OFF Default ON TIMERS READY TO POWER SAVER Controls the length of time the printer will remain idle before entering power saver mode Settings 5 to 50 minutes in 5 minute intervals Default 50 minutes NOTE A value of O prevents the printer from entering power saver mode POWER SAVER TO REST Controls the length of time the printer will remain idle in power saver mode before entering rest mode Settings 15 to 150 minutes in 15 minute intervals Default 150 minutes NOTE A value of O prevents the printer from entering rest mode PRINTER ADJUSTMENTS DENSITY Increases or decreases the print density Settings 0 lightest to 10 darkest Default 5 FINISHER SETTINGS FINISHER CONFIG TYPE Specifies the folder configuration type Settings NONE no finisher and 003 Generic Finisher Interface Default NONE 20 XEROX WIDE FORMAT 510dp OPERATOR MANUAL OFF LINE SETUP MENU Table 1 Printer Menu options continued DIAGNOSTICS TEST PLOT Allows you to run a test print in off line mode from each media source The selections are
20. ave not changed the type or width of the roll media in the drawer press the Exit key If you have changed the type or width you must enter the new information To change the roll media size and type 1 Press the Media key The message display indicates the width and type of roll media last specified for drawer 1 NOTE The Media key is active from either on line or off line mode Press the Previous or Next key to scroll through the media source selections The selections are ROLL1 ROLL2 ROLL3 and BYPASS SHELF cut sheet feed in shelf When you scroll to the media source you want to change press the Enter key The message display instructs you to select the media width It indicates the current media width NOTE Media width does not apply to the BYPASS SHELF selection If you have selected BYPASS SHELF as the media source the message display instructs you to select the media type Proceed to step 6 Press the Previous or Next key to scroll through the media width selections The width selections are 11 0 INCH 297 MM 12 0 INCH 353 MM 17 0 INCH 420 MM 18 0 INCH 500 MM 22 0 INCH 594 MM 24 0 INCH 620 MM 30 0 INCH 707 MM 34 0 INCH 750 MM 36 0 INCH 841 MM 860 MM 880 MM 900 MM When you scroll to the desired media width press the Enter key The message display instructs you to select the media type It indicates the current media type XEROX WIDE FORMAT 510dp OPERATOR MANUAL XEROX WIDE FORMAT 5109
21. cartridge and waste bottle according to the instructions provided with the replacement carton 33 Cleaning the printer surface As needed clean the outside surfaces of the printer Use a clean cloth dampened with mild soap and water Do not pour or spray liquid directly on any part of the printer 34 XEROX WIDE FORMAT 510dp OPERATOR MANUAL Ordering supplies Supply order list Supply order procedure XEROX WIDE FORMAT 510dp OPERATOR MANUAL CARE This section provides information for obtaining supplies for your printer The XEROX Wide Format 510dp uses the following supplies e Toner cartridge and toner waste bottle The printer is shipped with one toner cartridge and one toner waste bottle Each time the toner cartridge empties you must replace both the cartridge and the waste bottle The two items are packaged together as one part number When ordering use the following part number United States 6R989 Europe 6R90302 Bond paper vellum tracing paper and film Xerox offers the above media in various sizes weights and grades to meet your printing needs To order supplies for the XEROX Wide Format 510 call your local Xerox Engineering Systems sales office Local telephone number When ordering supplies please be prepared to provide the following information to the sales representative e Customer account number e Machine type XEROX Wide Format 510dp e descrip
22. d solutions in the table For problems beyond the scope of this table call for service Table 4 Problem Solving Table Portions of the prints are deleted The media may be damp Check the condition of the media If damp replace it Store the media in a sealed package or bag The prints are light overall or have The print density may be too light Use the Printer Menu to adjust the light areas print density Refer to Adjusting the print density in this manual The media may be too damp If media is damp replace it Use a sealed media drawer Store the media in a sealed package or bag The tracing paper has wrinkles The media may be too dry Use a sealed media drawer Store the media in a sealed package or bag Image is missing on left and right When using the Scale to fit option Do not use a zero margin setting sides of the print when using the the margins may have been set 0 when using Scale to fit Try adding Scale to fit option zero a margin and increasing it if necessary until the image is on the print 46 XEROX WIDE FORMAT 510dp OPERATOR MANUAL PROBLEM SOLVING Calling for service When you experience a problem with the printer you may be able to resolve it by referring to the procedures and tables in this chapter If you are unable to resolve the problem call your local Xerox Engineering Systems office Local telephone number A customer service representative will answer any questions you
23. e has been intentionally left blank 6 XEROX Wide Format 510dp OPERATOR MANUAL Circuit breaker switch Printer power switch WIDE FORMAT 510dp OPERATOR MANUAL 2 Powering and off This chapter describes the procedures for powering on and powering off It also describes the power consumption modes Powering on NERON ENGINE p SINCE NC YSTEMS Controller power switch 1 Switch the circuit breaker to the On 1 position This turns on power to the Printer 2 Switch the printer power switch to the On 1 position This turns on the printer 3 Switch on the Controller NOTE During the warm up cycle the message display provides a FUSER CALIBRATING message then a printer is warming up message and decreasing fuser warm up codes of L9 to LO When the warm up completes the printer on line and ready to print The message display indicates XES SYNERGIX 510dp IDLE POWERING AND OFF Powering off To power off 1 Switch the printer power switch to the Off O position This turns off the printer Switch off the Controller Switch the circuit breaker to the Off position This turns off power to the Printer Power consumption modes Running Ready Power saver Rest The printer has four power consumption modes They are The printer is capable of making prints immediately in this mode When in this mode the message display indicate
24. e of one of the standard media drawers 3 Doone of the following e If the drawer is a sealed media drawer raise the Plexiglas cover until it holds in place e If the drawer is not a sealed media drawer proceed to step 4 4 Squeeze the baffle release and raise the baffle until it locks in lt gt place 2 2 10 XEROX WIDE FORMAT 5109 OPERATOR MANUAL MEDIA 5 Rotate the media roll to wind the end of the media onto the roll 6 Liftthe media roll out of the drawer 7 Laythe media roll on a flat horizontal surface 8 Squeeze the lever at the end of the media roll support tube and remove the tube from the media roll 9 Lay the new media roll on a flat horizontal surface 10 Slide the end of the media roll support tube without the lever into the new media roll as far as it will go XEROX WIDE FORMAT 510dp OPERATOR MANUAL 11 MEDIA 11 Squeeze the lever at the end of the media roll support tube and position the tube until the size indicators on the tube match the size of the roll e For example if the media roll is 36 inches the ends of the media roll should be at the 36 inch markers on the media roll support tube 12 Place the new media roll into the media drawer so that the lead edge of the paper is on the underside of the roll and toward the printer 13 Position the media roll support tube so that the ends of the tube rest within the support rollers at the sides of the drawer e
25. en the toner cartridge needs replacement XEROX WIDE FORMAT 510dp OPERATOR MANUAL When the toner cartridge is empty the following occur e The toner supply access cover indicator on the graphic display flashes e The alarm beep if enabled sounds e A J1 01 status code and a message instructing you to replace the dry ink cartridge and waste bottle appear in the message display To replace the toner cartridge and toner waste bottle follow the instructions in the Replacing the toner cartridge and Replacing the toner waste bottle sections of this chapter 27 Replacing the toner cartridge To replace the toner cartridge CAUTION Toner identified for use in XEROX Wide Format 510dp is a two component material made specifically for this printer Use of toner not identified for the XEROX Wide Format 510dp will damage the printer 1 Open the replacement toner carton e Remove the replacement toner cartridge e Remove the replacement toner waste bottle e Save all the replacement toner packaging for recycling the used toner cartridge and toner waste bottle 2 Open the toner supply access cover 3 Slide the gold cartridge dispenser patch cover to the left to expose the dispenser patch 4 Pull the plunger to the right and lift the front end of the toner cartridge 5 Release the plunger and rest the cartridge on the plunger mechanism 28 XEROX WIDE FORMAT 510dp OPERATOR MANUAL XEROX WIDE
26. ext key Enter key Exit key The control panel is located on top of the front side of the printer It consists of a graphic display a message display several function keys and a numeric keypad FRON ENGINEERING Ex sy This is an illustration of the printer with indicator lights for the front door the cutter drawer the toner supply access cover the cut sheet feed in shelf drawer 1 drawer 2 and drawer 3 The indicator lights have three states Off is the normal state and signifies that no operator attention is required On signifies that the associated interlock is open Flashing signifies that operator attention is required Press this key to display and modify the current width if applicable and type settings for the media sources drawer 1 drawer 2 drawer 3 and cut sheet feed in shelf This key is active from both on line and off line modes Pressing this key while in off line mode always displays the media settings regardless of which off line menu is currently active This is a 2 line 40 character per line display Press this key to move backward through the printer menus and selections For numeric values pressing this key decreases the value by one unit Press this key to move forward through the printer menus and selections For numeric values pressing this key increases the value by one unit Press this key to select the current menu item or value Press this key to undo the
27. finisher configuration type Performing printer diagnostics 24 Note If there is a Scanner connected the message displayed will be SYNERGIX CS 510dp If there is no Scanner connected the message will be SYNERGIX PS 510dp To specify the finisher configuration type 1 Access the PRINTER MENU See Accessing the Printer Menu in this chapter 2 Press the Previous or Next key until FINISHER SETTINGS is displayed Press the Enter key to select FINISHER SETTINGS Press the Enter key to select FINISHER CONFIG TYPE The current value for the FINISHER CONFIG TYPE option is displayed 5 Press the Previous or Next key to switch between NONE and 003 Press the Enter key to save your selection Press the On line Off line key to return to on line mode e The on line off line indicator will light e The display will indicate SYNERGIX CS 510dp IDLE or SYNERGIX PS 510 The DIAGNOSTICS option has two operator accessible sub options TEST PLOT and RECENT FAULT LOG NOTE A third DIAGNOSTICS option PRINTER DIAGNOSTICS is restricted to the service representative If you select it you will be asked to enter a password Press the Exit key to exit the option Printing a test plot Note If there is a Scanner connected the message displayed will be SYNERGIX CS 510dp If there is no Scanner connected the message will be SYNERGIX PS 510dp To print a test plot 1 Access the PRINTER MENU See Accessing the Printer
28. luding mixed sizes The tray can be raised for access to the cut sheet feed in shelf and the media supply drawers Open to load paper rolls and to clear media jams in drawer 1 Open to load paper rolls and to clear media jams in drawer 2 Open to load paper rolls and to clear media jams in drawer 3 Insert cut sheets here to bypass the roll media in the drawers Use this bypass when the drawers do not contain the correct media size or a nonstandard media size is required Open to clear jams in the fuser area Open to access the toner waste bottle and to view the product serial number Contains the graphic display message display menu access and navigation keys and numeric keypad Drawers 2 and 3 are available as options XEROX Wide Format 510dp OPERATOR MANUAL 1 Cutter drawer Printer on off switch white Power cord connection Circuit breaker switch black 9r oA o qm Toner supply access cover XEROX WIDE FORMAT 510dp OPERATOR MANUAL PRINTER OVERVIEW Open to clear media jams in the cutter area WARNING The cutter blade is very sharp Do not touch the cutter blade when clearing media jams in the cutter area Press to switch the printer on or off Connect the power cord here and to a suitable power outlet Press to turn power to the Printer on or off Open to replace the toner cartridge PRINTER OVERVIEW Control panel 1 Graphic display 2 Media key Message display Previous key 5 N
29. mm Audible noise 67 db Max Power consumption Typical power consumption for US 220V 0 20A Warm up 4660 watts Standby 1000 watts Operating 2100 watts Rest 120 watts Heat output Warm up 14 500 BTU hour Standby mode 4 000 BTU hour Print mode 7 200 BTU hour Finishing Standard catch tray Optional on line folder Optional Synergix Stacker XEROX WIDE FORMAT 510dp OPERATOR MANUAL 49 TECHNICAL DATA The XEROX Wide Format 510dp will operate within the specifications indicated in the table below for the respective markets Current limit will be set as part of the installation procedure The printer is not sensitive to the AC power service frequency and can operate at either 50hz or 60hz Table 6 Operating Power Market area AC power service Maximum current First Print Out Time rating consumption US Canada 208V 240V 20 17 6A Less than 3 minutes 208V 240V 15A 13 2A Less than 4 minutes European Operations 230V 240V 16A 16 0A Less than 3 minutes Common Market United Kingdom 230V 240V 13A 13 0A Less than 3 5 minutes Switzerland 220V 10A 10 0A Less than 5 minutes Central South America 220V 240V 20 Less than 3 minutes The table below shows maximum print throughput in prints per minute It assumes continuous printing from a single roll with no AC power limitation Table 7 Maximum Prints Per Minute US Europe Central and South America 50 XEROX WIDE FORMAT 510dp
30. n place of one of the standard media drawers 3 Do one of the following e fthe drawer is a sealed media drawer raise the Plexiglas cover until it snaps in place drawer is not a sealed media drawer proceed to step 4 4 Squeeze the baffle release and raise the baffle until it locks in place XEROX WIDE FORMAT 510dp OPERATOR MANUAL 41 PROBLEM SOLVING 42 5 Rotate the media roll to wind the end of the media onto the roll 6 Examine the lead edge of the media for tears e If the lead edge of the media is torn folded creased or uneven trim the lead edge T Rotate the media roll to feed the media under the baffle and beyond the registration window 8 Squeeze the baffle release and lower the baffle until it locks in place on both sides XEROX WIDE FORMAT 510dp OPERATOR MANUAL XEROX WIDE FORMAT 5109 OPERATOR MANUAL 11 PROBLEM SOLVING Slowly rotate the media roll until the lead edge of the media is centered in the registration window Do one of the following e fthe drawer is a sealed media drawer close the Plexiglas cover e Ifthe drawer is not a sealed media drawer proceed to step 11 Close the roll media drawer 12 Lower the output tray 43 PROBLEM SOLVING Status codes The status codes shown in the table below may appear on the message display Follow the instructions in the table before calling for service Table 2 Status Code Table Sta
31. nt Shielded cables must be used with this equipment to maintain compliance with the EMC Directive 89 336 EEC WARNING In order to allow this equipment to operate in proximity to Industrial Scientific and Medical ISM equipment the external radiation from ISM equipment may have to be limited or special mitigation measures taken Canada This Class A digital apparatus complies with Canadian ICES 0003 Cet appareil num rique de la classe A est conforme la norme NMB 003 du Canada XEROX WIDE FORMAT 510DP OPERATOR MANUAL iii NOTICES Japan This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment VCCI If this equipment is used in a domestic environment radio disturbance may arise When such trouble occurs the user may be required to take corrective actions Changes or modifications to this equipment not specifically approved by Fuji Xerox Limited may void the user s authority to operate this equipment Shielded cables must be used with this equipment to maintain compliance with the Voluntary Control Council for Interference by Information Technology Equipment regulations USA This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment i
32. o di LIE 1 Mal COMPONEN ai Mmm dm 2 Control E 4 2 Powering ON and eri su cues 7 POWenrING rd iba do 8 Power CONSUMPTION Modes RR RR 8 3 Media i 9 When a media roll 9 Loading the roll media 2 5 n Et etel t e eet teret b heen DER 10 Changing the roll media size and 14 Using the cut sheet feed in 1 0 4 221 21 1 1 4014 111441141 00001 annt tenir nennen nentes nenas 16 Automatic media roll SWItCHiNg 17 Media storage tips eee A ctt et bts 17 4 Off line Setup 19 ties cede lada 19 Printer Menu stint ete bem ll rd cede fein tae 20 Accessing the Printer Menu 1 1 4041 02 4 4 1044 01 dnte d 22 Enabling or disabling the a
33. ode e The on line off line indicator will light e display will indicate SYNERGIX CS 510dp IDLE or SYNERGIX PS 510dp Note If there is a Scanner connected the message displayed will be SYNERGIX CS 510dp If there is no Scanner connected the message will be SYNERGIX PS 510 To display the billing meter counts 1 Access the PRINTER MENU See Accessing the Printer Menu in this chapter 2 Press the Previous or Next key until BILLING METERS is displayed 3 Press the Enter key to select BILLING METERS The value for METER is displayed METER A provides the square footage of prints produced 4 To view the value for METER B press the Previous or Next key METER B provides the linear feet of media produced 5 When you are finished viewing the meter counts press the On line Off line key to return to on line mode e The on line off line indicator will light e display will indicate SYNERGIX CS 510dp IDLE or SYNERGIX PS 510 25 OFF LINE SETUP MENU This page has been intentionally left blank 26 XEROX WIDE FORMAT 510dp OPERATOR MANUAL 5 The printer requires a minimum of operator maintenance You will need to replace the toner cartridge and toner waste bottle when the cartridge empties You also will need to clean the outside surface of the printer when necessary This chapter provides the procedures for performing the required tasks and for ordering supplies Wh
34. on device with Synergix Scan System and an 5 controller The Synergix Stacker and a full featured Folder are optional accessories for either configuration The printer depending on the option installed has a throughput of 5 7 or 10 D size A1 prints per minute at a process speed of 4 5 inches per second Depending on the selected options it is equipped with one two or three media drawers that can hold roll media from 11 to 36 inches wide and up to 500 feet long An optional sealed media drawer is available in place of standard media drawers for locations that experience humidity extremes For jobs requiring non standard media sizes the printer has a cut sheet feed in shelf that enables you to bypass the media drawers It also has a standard catch tray that can accommodate up to 100 prints of all sizes Organization and content of this manual Chapter 1 Chapter 2 Chapter 3 Chapter 4 XEROX WIDE FORMAT 510dp OPERATOR MANUAL The XEROX Wide Format 510dp Operator Manual provides the information you need to become familiar with the components features operation and specifications of your printer It contains the following chapters Printer overview This chapter shows the orientation of the printer It illustrates and describes the main components of the printer and the control panel Powering on and off This chapter provides instructions for powering on and powering off and explains the power consumpti
35. on modes of the printer Media This chapter explains what happens when a media roll empties how to load a media roll and how to specify the size and type of a media roll It provides the procedure for using cut sheet media and describes the automatic roll switching feature Additionally it lists some tips for storing your media Off line Setup Menu This chapter lists the Setup Menu options and provides detailed instructions for using the Printer Menu sub option INTRODUCTION Chapter 5 Chapter 6 Chapter 7 Care This chapter contains instructions for replacing the toner cartridge and toner waste bottle and cleaning the printer surface It also lists the supplies needed and the procedure for ordering them Problem solving This chapter provides the procedures for clearing jams It contains status code and error message tables as well as a general problem solving table For problems you are unable to resolve by using this manual it also explains the procedure for placing a call for service Technical data This chapter contains product and paper specifications as well as space requirements for operation of the printer Terminology used in this manual Printer Whenever the term printer appears in this manual it refers to the XEROX Wide Format 510 Conventions used in this manual viii Bold WARNING CAUTION NOTE This manual uses the following conventions Boldface characters in a
36. r example roll 3 empties and both roll 1 and roll 2 contain the same media size and type the printer will Switch to roll 1 If roll 1 empties the printer will switch to roll 2 Media storage tips To obtain maximum results from your print media follow these media storage tips e Store cut sheet media flat not on edge in a closed cut sheet media package Store roll media on end in an appropriately sealed media bag e Store the media in a cool dry environment XEROX WIDE FORMAT 510dp OPERATOR MANUAL 17 MEDIA This page has been intentionally left blank 18 XEROX WIDE FORMAT 510dp OPERATOR MANUAL 4 Off line Setup Menu The printer has an off line Setup Menu that allows you to customize the printer and the AccXES controller to meet your particular requirements Setup Menu options XEROX WIDE FORMAT 510dp OPERATOR MANUAL The Setup Menu has the following options e Utilities e Setup I O Ports e Setup Printers e Processing Defaults e System Administration e Printer Menu Each of the Setup Menu options has a number of sub options This chapter documents the Printer Menu option in detail For information about the remaining Setup Menu options refer to the 5 Synergix 8825 8830 8850 510dp Controller Setup Manual for Firmware 9 0 or the Web Printer Manager Tool User Guide 19 OFF LINE SETUP MENU Printer Menu The Printer Menu allows you to control the operation of the printer This menu cont
37. s operated in a commercial environment This equipment generates uses and radiate radio frequency energy if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Changes or modifications to this equipment not specifically approved by the Xerox Corporation may void the user s authority to operate this equipment Shielded cables must be used with this equipment to maintain compliance with FCC regulations XEROX WIDE FORMAT 510ddpOPERATOR MANUAL XEROX WIDE FORMAT 510DP OPERATOR MANUAL Safety notes Your system has been designed and tested to meet strict safety requirements These include safety agency examination and approval plus compliance with established environmental standards Please read the following instructions carefully before operating the printer and refer to them as needed to ensure continued safe operations Follow all warnings and instructions marked on or supplied with the product Unplug the units from the wall outlet before cleaning the exterior Always use materials specifically designated for the printer Use of other materials may result in poor performance and could create a hazardous situation Do not use aerosol cleaners Follow the instructions in
38. s that the printer is PRINTING The printer enters this mode 2 to 30 seconds after completion of a print When in this mode the message display indicates that the printer is IDLE The printer enters this mode to reduce energy consumption after a specified period of inactivity since the completion of the last print This time period is user programmable The range is 5 to 50 minutes See the Off line Setup Menu chapter for more information about setting the power saver timer NOTE When the printer is in this mode the fuser is at low power The printer needs to warm up from an L3 status code before being ready to print The printer enters this mode to minimize energy consumption after a specified period of inactivity since entering power saver mode This time period is user programmable The range is 15 to 150 minutes See the Off line Setup Menu chapter for more information about setting the rest mode timer NOTE When the printer is in this mode the fuser is off The printer needs to warm up from an L9 status code before being ready to print XEROX Wide Format 510dp OPERATOR MANUAL Media This chapter provides the following information A listing of the ways in which the printer notifies you when a media roll is low or empty The procedure for loading roll media into the media drawers The procedure for specifying the media size and type for each media drawer The procedure for bypassing the media drawers and man
39. this operator guide for the proper cleaning methods Never use supplies or cleaning materials for purposes other than what they were intended Keep all supplies and materials out of the reach of children Do not use the units near water wet locations or outdoors The components of this product are equipped with a three wire grounding type plug i e a plug having a grounding pin This plug will only fit into a grounding type power outlet This is a safety feature To avoid the risk of electric shock contact your electrician to replace the receptacle if you are unable to insert the plug into the outlet Never use a ground adapter plug to connect the system to a power source that lacks a ground connection terminal This system should be operated from the type of power source indicated on the marking label If you are not sure of the type of power available consult your local power company The power supply cord is the disconnect device for this equipment Make sure that the installation is near the socket outlet and is easily accessible Do not allow anything to rest on the power cord Do not locate the units where someone will step on the cord The units should not be placed in a built in installation unless proper ventilation is provided SAFETY NOTES vi Never push objects of any kind into the slots of the units as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric
40. tions part numbers and quantities required For more information visit the Xerox Engineering Systems web site at www xes com 35 This page intentionally left blank 36 XEROX WIDE FORMAT 510dp OPERATOR MANUAL 6 Problem solving This chapter provides information for resolving various problems that can occur during the operation of the printer It contains instructions for clearing media jams It also includes status code and error message tables as well as a general problem solving table If you are unable to resolve the problem follow the procedure for calling for service at the end of the chapter Clearing media jams XEROX WIDE FORMAT 510dp OPERATOR MANUAL When the printer experiences a media jam the following occur e The alarm beep if enabled sounds e indicator light on the graphic display in the area of the jam flashes A status code and instructions for resolving the problem appear in the message display To clear the jam e Observe the location of the flashing indicator light on the graphic display e Follow the instructions in the message display and in this section of the operator manual 37 PROBLEM SOLVING Fuser area jam To clear a jam in the fuser area 1 Raise the output tray all the way so that it rests on top of the printer WARNING Do not touch the fuser roll while clearing media jams in the fuser area The fuser roll is very hot and can cause severe burns
41. tus code Explanation CO This code indicates a cutter problem Follow the instructions on the message display This code indicates a problem with roll 1 Follow the instructions on the message display This code indicates a problem with roll 2 Follow the instructions on the message display This code indicates a problem with roll 3 Follow the instructions on the message display C4 This code indicates a problem at the cut sheet feed in shelf Follow the instructions on the message display E2 This code indicates a problem in the paper path Follow the instructions on the message display This code indicates a problem in the fuser area Follow the instructions on the message display This code indicates an interlock problem Follow the instructions on the message display This code indicates a problem in the paper path Follow the instructions on the message display E7 This code indicates a communication failure with the AccXES controller Switch the printer and controller off Wait a few seconds Then switch the controller and printer on Switch the printer off Wait a few seconds Then switch the printer on F1 This code indicates a problem in the finisher Follow the instructions on the message display 2 This code indicates a problem in the finisher Follow the instructions on the message display 41 01 This code indicates that the toner cartridge should be replaced Refer to the Replacing the toner cartridge
42. ually feeding cut sheets into the printer An explanation of the automatic roll switching feature Tips for safe storage of your printer media For information about the media sizes and types that the printer can accommodate refer to the Technical data chapter of this manual When a media roll empties XEROX WIDE FORMAT 510dp OPERATOR MANUAL When roll media drawer has less than 30 feet of media or is empty the printer alerts you in the following ways The applicable drawer indicator light on the graphic display flashes If you submit a job requiring the empty media source the alarm beep if enabled sounds once and the message display instructs you to install the required media If ajob is printing and the media roll empties the alarm beep if enabled sounds steadily and a C 1 2 3 04 or C 1 2 3 05 status code and a message instructing you to re feed the roll appear in the display If you press the Media key and scroll to the applicable media source the message display advises you that the media roll is low or empty MEDIA Loading the roll media To load a media roll 1 Raise the output tray all the way so that it rests on top of the printer 2 Lift the handle of the applicable drawer and open the drawer all the way NOTE In some locations high or low humidity affects the media and causes print quality problems To resolve the problems a sealed media drawer can be installed on the printer in plac
43. udible enne nennen 22 Setting the tlTiers epe Alas 23 Adjusting the print density 2 2 1111100 raa b hs ed 23 Specifying the finisher configuration 24 Performing printer 24 Printing a test plot met Uti id 24 Viewing the recent fault 100 nnn nnne th a nnne 25 Displaying the billing meter enm ene nennen nennen nennen nennen nnns 25 ECC M 27 When the toner cartridge needs eene nennen 27 Replacing the toner 2 1 1 2 2 2411004 4 0 1 41 000001 nne a ea nantes 28 Replacing the toner waste 31 Cleaning the printer Surface etes Pee Ee eet rena Lex Maa Me e EL n e nee Enea 34 Ordering Supplies s n e t ertet olt re eter A eit a ced ro 35 o pply ordet list 3 is t eL o ete n tat tarte aei m tees dels fade edes ee da 35 Supply Order procedure o o rte Ebo T eat Hatte e t 35 6 Problem SOLVING 37 Clearing media JanS x Ds
44. ver media type you manually feed into it regardless of the media type you specify You should ensure that the media type is correct however as the printer uses the media type to determine the fuser temperature The wrong fuser temperature could cause poor print quality It could also result in a maintenance service call if any toner rubs off the media onto the fuser roll Center the media between the size indicators on the cut sheet feed in shelf Feed the lead edge of the media squarely into the printer until the printer grabs and advances the media From the client workstation specify Manual Feed as the media Source Submit the print job When you are finished manually feeding cut sheets lower the output tray XEROX WIDE FORMAT 510dp OPERATOR MANUAL MEDIA Automatic media roll switching The printer has an automatic roll switching feature that allows it to switch to another roll when the roll in use empties This feature provides for longer continuous operation of the printer Automatic switching is possible only if the following conditions are met e The printer has more than one drawer e Another drawer contains a media roll of the identical size and type as the roll in use e The print job has not specified a particular roll e g roll 1 If both of the remaining media drawers contain the identical media size and type as the roll is in use the printer will select the lowest numbered drawer first If fo
Download Pdf Manuals
Related Search