Xantrex Technology 300 PLUS Power Supply User Manual
Contents
1. 30 Battery Life 30 Obtaining a Replacement Battery 31 Replacing the Battery 32 Replacing the Fluorescent Tubes 34 Replacing the External Fuse 34 5 Troubleshooting Common Problems 36 Buzz in Audio Equipment 36 Television Interference 36 Troubleshooting Reference 36 6 Specifications Electrical Specifications 41 Physical Specifications 43 Contents 7 Warranty and Product I nformation Warranty Information 45 Returning a Product 47 Out of Warranty Service 48 Contacting Xantrex Customer Service 49 xi xii I ntroduction About the XPower Powerpack Thank you for purchasing the XPower Powerpack Easy to use and designed for years of reliable service the XPower Powerpack can run many AC appliances and 12 volt DC appliances whenever you need power for work or play at home or on the road XPower Powerpack e Powers 115 volt AC appliances e Powers 12 volt DC appliances e Jump starts vehicle engines e Provides fluorescent lighting for emergency use2. XPower Powerpack 300 and 300 PLUS xantrex About Xantrex Xantrex Technology Inc develops manufactures and markets leading advanced power electronic and control products for the Distributed Mobile and Programmable Power markets The company s enabling technology converts raw electrical power from any central distributed or backup power source into high quality power required by electronic and electrical equipment Its products are sold under the Xantrex Trace Heart and Statpower brands Trademarks XPower is a trademark of Xantrex International Xantrex is a registered trademark of Xantrex International Other trademarks registered trademarks and product names are the property of their respective owners and are used herein for identification purposes only May 2002 Xantrex International All rights reserved Notice of Copyright XPower Powerpack 300 and 300 Plus Owner s Guide May 2002 Xantrex International All rights reserved Disclaimer UNLESS SPECIFICALLY AGREED TO IN WRITING XANTREX TECHNOLOGY INC XANTREX a MAKES NO WARRANTY AS TO THE ACCURACY SUFFICIENCY OR SUITABILITY OF ANY TECHNICAL OR OTHER INFORMATION PROVIDED IN ITS MANUALS OR OTHER DOCUMENTATION b ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSS OR DAMAGE WHETHER DIRECT INDIRECT CONSEQUENTIAL OR INCIDENTAL WHICH MIGHT ARISE OUT OF THE USE OF SUCH INFORMATION THE USE OF ANY SUCH INFORMATION WILL BE ENTIRELY AT
3. 41 Electrical Specifications AC Power Section Output power e Continuous output power 250 W e Five minute AC output power 300 W e AC output surge capacity 500 W Output voltage 115 10 VAC RMS Output frequency 60 Hz 4 Hz Output wave form modified sinewave No load current draw lt 0 20A DC Input voltage range 10 0 to 15 0 VDC Low battery alarm 10 7 VDC Low battery shutdown 10 0 VDC High battery voltage shutdown Yes automatic reset Over temperature shutdown Yes automatic reset Overload shutdown Yes automatic reset AC output short circuit protection Yes automatic reset Fuse 40 A user replaceable Operating temperature range 32 F to 104 F 0 C to 40 C Storage temperature range 32 F to 86 F 0 C to 30 C Internal Battery Charging Controller System AC Charger bulk charging current 500 mA Peak charging voltage nominal 14 5 V Charge restart voltage nominal 12 9 V Float charge after full charge is completed I mA nominal AC Charger input socket maximum current 25A 42 Physical Specifications Air compressor XPower Powerpack 300 250 PSI Ib in Plus only Accessories Jump start cables 39 inches 1 m 8 AWG wire with black and red battery clips DC charge cable 39 inches 1 m 18 AWG with male to male lighter plugs AC Charger input 120 10 VAC
4. cylinder head or other stationary heavy metal part of the motor or to the negative battery terminal The Battery Clips Connected Properly green light illuminates Before starting the engine make sure the XPower Powerpack and the jump start cables are clear of belts and fans Do not crank the engine for more than 4 seconds Once the engine has started go to Step 10 OR The reverse polarity alarm sounds and the Battery Clips Connected Improperly red light illuminates 8 Remove the red positive clip first and then the black negative clip to cancel the alarm 9 Repeat steps 1 5 6 and 7 When the Battery Clips Connected Properly green light is illuminated make sure that the XPower Powerpack and the jump start cables are clear of belts and fans before attempting to start the engine Do not remove the jump start cables from the Jumper Cable Port when the positive and negative clips are connected to the vehicle s battery terminals Removing the jump start cables from the Jumper Cable Port while they are connected to the vehicle s battery terminals disables the jump start safety feature and could result in sparking and explosion i WARNING Explosion 10 Remove the red positive clip and then the black negative clip from the vehicle s battery terminal 11 Remove the jump start cables from the Jumper Cable Port I mportant Recharge the XPower Powerpack as soon as possible a
5. Off Switch has three settings Off One Light and Two Lights Jumper Cable Port supplies high power DC current The jump start cables connect to the Jumper Cable Port when boosting a vehicle s starting battery or when connecting an external battery to the XPower Powerpack The jump start cable connection is designed so that the jump start cable cannot be inserted incorrectly into the Jumper Cable Port The jump start safety feature prevents sparking at the battery terminals and prevents potential damage to your vehicle s electrical system Accessories lll 7a yp Y Feature Accessories Description AC Charger lets you recharge the XPower Powerpack from a standard AC wall outlet and can only be used to recharge the internal battery of the XPower Powerpack Jump start cables provide a special jump start safety feature This feature enables the XPower Powerpack jump start ability only if the XPower Powerpack detects that the cables are connected to a battery correctly If the cables are connected to a battery incorrectly an alarm sounds and the Battery Clips Connected Improperly red light illuminates DC Charging Cable lets you recharge the XPower Powerpack from a 12 volt system in a car SUV RV or a boat Accessory bag Nozzle packet XPower Powerpack 300 Plus only contains 3 nozzles adaptors not shown in the Nozzle Adaptor Compartment 10 Operation Chapter 3
6. Powerpack as soon as possible after each use 16 Operating 12 Volt DC Appliances When using the XPower Powerpack to operate an AC appliance and the low battery warning sounds the warning gives you time to shut your AC appliance off before loss of AC power If you ignore the warning the XPower Powerpack automatically turns off a few minutes later to prevent battery damage In the event of an overload low battery voltage or overheating the XPower Powerpack automatically shuts down Operating 12 Volt DC Appliances The XPower Powerpack can operate 12 volt DC auto RV marine or other portable appliances that draw 12 amps or less from a 12 volt DC power outlet or from a vehicle s lighter socket The DC Power Socket does not automatically switch off when the internal battery is discharged To protect the internal battery against damage resulting from total discharge Xantrex recommends that the AC Outlet On Off switch is turned On when using the XPower Powerpack to operate a 12 volt DC appliance i CAUTI ON Equipment damage Having the AC Outlet On Off switch turned On enables the alarm to warn you when the 12 volt DC appliance has nearly depleted the internal battery Note The fewer watts a 12 volt DC appliance draws the longer the XPower Powerpack will operate before recharging is required 17 Operating 12 Volt DC Appliances 18 Typical 12 volt DC appliances that can be used on the XPower Powerpa
7. THE USER S RISK Date and Revision May 2002 Revision 1 Part Number 445 0170 01 01 Contact I nformation Phone 1 800 670 0707 toll free in North America 1 604 420 1585 outside North America Fax 1 800 994 7828 toll free in North America 1 604 420 1591 outside North America Email CustomerService Xantrex com Web www xantrex com About This Guide Conventions Used The following conventions are used in this guide WARNING AN Warnings identify conditions that could result in personal injury or loss of life CAUTI ON A Cautions identify conditions or practices that could result in damage to the XPower Powerpack unit or to other equipment Important These notes describe an important action item or an item that you must pay attention to Note Notes describe additional information which may add to your understanding of how to use the XPower Powerpack About This Guide References to XPower Powerpack In this guide both the XPower Powerpack 300 and the XPower Powerpack 300 Plus with the air compressor are referred to as XPower Powerpack when the information applies to both models However when the information is specific to one model then reference is made specifically to the XPower Powerpack 300 or to the XPower Powerpack 300 Plus Related I nformation You can find more information about Xantrex Technology Inc as well as its products and services at www xantrex co
8. and one half times the operating time of the XPower Powerpack internal 20 amp hour battery Use a sealed non spillable battery for indoor use i WARNING Acid spills Common auto and marine batteries are not suitable for indoor use unless their fumes are vented outdoors Common auto and marine batteries contain acid which is hazardous if spilled Wear eye protection and protective clothing when connecting the XPower Powerpack to an external battery To connect the XPower Powerpack to an external battery using the jump start cables 1 Connect the jump start cables to the Jumper Cable Port on the left side of the XPower Powerpack Connect the red positive clip of the jump start cables to the red positive terminal of the external battery Connect the black negative clip of the jump start cables to the black negative terminal of the external battery 23 Connecting to an External Battery 24 5 The Battery Clips Connected Properly green light illuminates You can now use the XPower Powerpack OR The reverse polarity alarm sounds and the Battery Clips Connected Improperly red light illuminates go to Step 4 Remove the red positive clip first and then the black negative clip to cancel the alarm Repeat steps 2 and 3 Do not remove the jump start cables from the jumper i WARNING Sparking and Explosion cable port when the positive and negative clips are connected to
9. are only accurate when the XPower Powerpack has been disconnected from all appliances and all charging sources for fifteen minutes I mportant Do not leave the XPower Powerpack permanently connected to the vehicle s lighter socket or 12 volt accessory outlet Recharging with a Generator s Regulated 12 Volt DC Outlet CAUTION AN The generator output must be intended for battery charging and have an output of 15 volts or less An unregulated output or one that exceeds 15 volts DC can damage the battery Refer to the Owner s Guide accompanying your generator for detailed instructions on connecting the generator to a unit like the XPower Powerpack You can recharge the battery of the XPower Powerpack using a generator in several ways e Using the AC Charger to recharge the XPower Powerpack from a generator is possible but would require extended generator running time e Using a generator which has an auxiliary regulated 12 volt DC output designed for charging 12 volt batteries Most generators are equipped with them Use this power source for faster charging e Using a generator with a lighter socket for its 12 volt output Follow the connection instructions in Recharging with the DC Charging Cable on page 28 Most of the XPower Powerpack s battery capacity will be recharged in a few hours 29 Replacing the Internal Battery Note Battery Level indicators are only accurate when the XPower
10. explains how to operate the XPower Powerpack efficiently This chapter covers Recharging the XPower Powerpack for first time use Operating AC appliances and 12 volt DC appliances Jump starting a vehicle engine Connecting to an external battery for additional run time Using the compressor on the XPower Powerpack 300 Plus Operating Conditions and Guidelines CAUTION AN Read all operating instructions before operating the XPower Powerpack 11 Choosing a Location CAUTI ON AN Do not use the XPower Powerpack to operate any AC appliances or 12 volt DC appliances while recharging with the AC Charger The AC Charger may fail if AC appliances or 12 volt DC appliances are operated while the AC Charger is connected CAUTI ON The XPower Powerpack is not intended for use as a UPS Uninterruptible Power Supply Choosing a Location 12 WARNI NG Fire or explosion AN The XPower Powerpack contains components that tend to produce arcs or sparks To prevent fire or explosion do not operate the XPower Powerpack in compartments containing batteries or flammable materials or in locations that require ignition protected equipment The XPower Powerpack should be operated only in a location that meets these requirements Dry Cool Ventilated Safe Protected from battery gases Do not allow water or other liquids to drop or splash on the XPower Powerpack Ambient air temperature should
11. the terminals of the external battery Removing the jump start cable from the jumper cable port while they are connected to the vehicle s battery terminals will disable the jump start safety feature and could result in sparking or explosion To disconnect the jump start cables from an external battery and from the XPower Powerpack 1 To disconnect the XPower Powerpack from the external battery when the external battery is discharged or no longer needed remove the red positive clip and then remove the black negative clip Remove the jump start cables from the Jumper Cable Port Recharge the XPower Powerpack as soon as possible after use Maintenance Chapter 4 provides information on maintaining your internal battery recharging options for the internal battery and replacing user replaceable parts Routine maintenance is required to keep your XPower Powerpack operating properly Occasionally clean the exterior of the unit with a damp cloth to remove the accumulated dust and dirt WARNING Shock hazard AN Disconnect all sources of AC power and DC power before doing any type of maintenance Battery Maintenance All rechargeable batteries gradually discharge when left standing and you need to recharge them periodically to maintain maximum battery capacity The AC Charger supplied with the XPower Powerpack is designed to regulate the charging process ensuring that the battery is always fully charged b
12. 60 Hz Nozzle adaptor for air compressor on the two nozzle adaptors XPower Powerpack 300 Plus only ane Sports needle Adaptor Physical Specifications XPower Powerpack 300 XPower Powerpack 300 Plus Depth 5 1 inches 13 0 cm 7 2 inches 18 2 cm Width 12 5 inches 31 8 cm 12 5 inches 31 8 cm Height 11 8 inches 30 0 cm 11 8 inches 30 0 cm Weight 18 0 Ibs 8 2 kg 20 0 Ibs 9 0 kg Important All specifications are subject to change without notice 43 44 Warranty and Product I nformation Warranty I nformation What does this warranty cover Xantrex manufactures its products from parts and components that are new or equivalent to new in accordance with industry standard practices This warranty covers any defects in workmanship or materials How long does the coverage last This warranty lasts for six months 6 months from the date of purchase Implied warranties of merchantability and fitness for a particular purpose are limited to six months from date of purchase Some jurisdictions do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you What does this warranty not cover This warranty will not apply where the product has been misused neglected improperly installed physically damaged or altered either internally or externally or damaged from improper use or use in an unsuitable environment Xantrex does not warran
13. In addition the XPower Powerpack 300 Plus with air compressor inflates tires and small sports equipment Comprehensive Protection Comprehensive Protection Automatic overload The XPower Powerpack has built in protection against output overload If you connect an appliance to the AC Outlet that draws more than 250 watts or one which draws excessive surge power the power to the AC Outlet automatically shuts off Overheating The XPower Powerpack is protected from overheating If the inverter exceeds a safe temperature power to the AC Outlet automatically shuts off Low Battery Protection Low battery protection protects the internal battery from excessive discharge and possible damage When the AC Outlet On Off switch is turned on an audible alarm alerts you when the internal battery is nearly discharged 10 7 volts DC and the unit turns off at 10 0 volts DC Jump start Cables Safety Feature and Reverse Polarity Detection The XPower Powerpack has a special jump start safety feature that eliminates the sparking that sometimes occurs when the jump start cables are connected to a battery The XPower Powerpack can also detect a reverse polarity connection and notifies you with an audible alarm and a Battery Clips Connected Improperly red light The battery to be jump started must have a terminal voltage of at least 4 volts in order to work with the XPower Powerpack Features Chapter 2 describes the main features of the
14. Powerpack has been disconnected from all appliances and all charging sources for fifteen minutes Recharging From a Solar Panel Small unregulated 12 volt solar panels rated to produce a maximum of 2 5 amps or 30 watts can be used to charge the XPower Powerpack through the Charger Input Socket You will need to purchase a standard 5 5 mm OD x 2 5 mm ID DC Coaxial barrel type connector to mate with the Charger Input Socket To recharge with a solar panel 1 Connect the solar panel s red positive wire to the coaxial plug s inner contact 2 Connect the solar panel s black negative wire to the plug s outer contact Once the connector is inserted into the Charger Input Socket and the solar panel is placed in the sun the XPower Powerpack charges automatically just as with the AC Charger See Recharging with the AC Charger on page 27 It takes about ten hours in direct sunlight to recharge the XPower Powerpack from a 2 5 amp solar panel Replacing the I nternal Battery Battery Life 30 The high quality battery used in the XPower Powerpack will serve as a reliable power source for years when properly maintained To maximize battery life it is important to recharge the XPower Powerpack battery after each use Replacing the Internal Battery I mportant Recharge the XPower Powerpack fully at least every three months if it is placed in storage or in a vehicle trunk Store in a location that
15. XPower Powerpack Xantrex recommends that you familiarize yourself with these features before operating the unit Materials List Your XPower Powerpack package includes these items o o o o o o XPower Powerpack 300 or XPower Powerpack 300 Plus Owner s Guide AC Charger DC Charging Cable Jump start Cables Accessory bag The XPower Powerpack 300 Plus also includes o o Two nozzle adaptors for the compressor One sports needle adaptor for the compressor If any of these materials are missing or are unsatisfactory in any way please contact Customer Service See Contacting Xantrex Customer Service on page 49 of this guide XPower Powerpack Features XPower Powerpack Features Front Panel Detail Feature BATTERY LEVEL 0 40 00 EMPTY FULL EHICLE JUMP START REVERSE BATTERY eters ea CONNECTED IMPROPERLY Description ie RECHARGE Oncaoy O OcHarcinc r BATTERY STATUS k BATTERY clips CONNECTED PROPERLY 7 300 watts household power Note Battery Level indicators illuminate when you press the Battery Status button e 4 lights indicates full charge e 3 lights indicates 3 4 charge e 2 lights indicates 1 2 charge e light red light the battery is discharged empty and must be recharged promptly Battery Level indicators are accurate only when the XPower Po
16. ation implied warranties and conditions of merchantability and fitness for a particular purpose Out of Warranty Service 48 If the warranty period for your XPower Powerpack has expired if the unit was damaged by misuse or incorrect installation if other conditions of the warranty have not been met or if no dated proof of purchase is available your inverter may be serviced or replaced for a flat fee To return your XPower Powerpack for out of warranty service contact Xantrex Customer Service for a Return Material Authorization RMA number and follow the other steps outlined in Warranty Information on page 45 Payment options such as credit card or money order will be explained by the Customer Service Representative In cases where the minimum flat fee does not apply as with incomplete units or units with excessive damage an additional fee will be charged If applicable you will be contacted by Customer Service once your unit has been received Contacting Xantrex Customer Service Contacting Xantrex Customer Service If none of the troubleshooting suggestions work you will need to call Xantrex Customer Service Phone 1 800 670 0707 toll free in North America 1 604 420 1585 outside of North America Fax 1 800 994 7828 toll free in North America 1 604 420 1591 outside of North America Email CustomerService xantrex com Web www xantrex com If possible note the circumstances surrounding the failure belo
17. battery operated equipment uses a separate charger or transformer that is plugged into an AC receptacle and produces a low voltage charging output Some chargers for rechargeable batteries can be damaged if connected to the XPower Powerpack Do not use the following with the XPower Powerpack e Small battery operated appliances like flashlights razors and night lights that can be plugged directly into an AC receptacle to recharge e Some chargers for battery packs used in hand power tools These affected chargers display a warning label stating that dangerous voltages are present at the battery terminals Note If you are unsure about using your rechargeable appliance with the XPower Powerpack contact the equipment manufacturer to determine the rechargeable appliance s compatibility with the modified sinewave AC waveform of the XPower Powerpack Contents I mportant Safety I nformation Warnings and Cautions v Precautions When Working With Batteries vii Precautions for Using Rechargeable Appliances viii 1 Introduction About the XPower Powerpack 1 Comprehensive Protection 2 2 Features Materials List 3 XPower Powerpack Features 4 Front Panel Detail 4 Air Compressor XPower Powe
18. be between 32 F and 104 F 0 C and 40 C the cooler the better within this range Leave at least 2 inches 5 cm clearance around the XPower Powerpack for air flow Ensure that the ventilation openings are not obstructed Do not operate the unit in the same compartment as batteries or in any compartment capable of storing flammable liquids like gasoline Do not operate the unit where it will be exposed to battery gases These gases are very corrosive and prolonged exposure will damage the XPower Powerpack Using XPower Powerpack for the First Time Using XPower Powerpack for the First Time I mportant Prior to operating your AC appliance or 12 volt DC appliance ensure that the battery of the XPower Powerpack is fully charged If the battery has been fully discharged recharging with the AC Charger may take up to 40 hours Be sure to recharge the XPower Powerpack immediately after purchase The easiest way to recharge the XPower Powerpack is to use the AC Charger See Recharging with the AC Charger on page 13 If you are interested in other options for recharging see Recharging the XPower Powerpack Battery on page 26 If you keep the XPower Powerpack in storage the battery will discharge over time Remember to recharge the battery every three months to keep the XPower Powerpack operational Recharging with the AC Charger Note The Battery Level indicators are only accurate when the XPower P
19. ck are listed in Table 2 Table 2 12 Volt DC Appliances and Run Times 12 Volt DC Appliance Watts Hours Cellular telephone 6 30 Fluorescent light built into 8 25 the unit Stereo CD player 10 19 Portable Cooler 30 4 1 Represents actual power consumption as measured on sample appliances 2 Operating times assume a fully charged battery and may very based on model or brand of appliance 3 Represents talks time available from 10 recharge cycles To operate a 12 volt DC appliance 1 Plug the 12 volt DC appliance into the DC power socket on the right side of the unit and turn the 12 volt DC appliance on if required If the 12 volt DC appliance draws more than 12 amps or has a short circuit defect the internal circuit breaker of the XPower Powerpack shuts off the power to the 12 volt DC appliance If this occurs unplug the 12 volt DC appliance and the internal circuit breaker automatically resets after a few seconds 2 Fully recharge the XPower Powerpack as soon as possible after each use As the DC power socket is internally wired directly to the internal battery extended operation of a 12 volt DC appliance may result in excessive battery discharge See Caution for Equipment damage on page 17 Jump starting a Vehicle Engine J ump starting a Vehicle Engine You can use the XPower Powerpack to jump start a vehicle engine that has a 12 volt starting battery using the supp
20. e type fuse which is available at many fuse opens of the XPower automotive parts stores Powerpack Reduce appliance power requirements to within power rating of the XPower Powerpack Over Inverter has Turn off the AC Outlet On Off temperature overheated due to poor switch and let the XPower shutdown ventilation or Powerpack cool down excessively warm environmental conditions Alarm sounds Internal battery is nearly discharged 10 7 volts If you ignore this warning the XPower Powerpack automatically switches off when the battery reaches 10 0 volts Recharge the XPower Powerpack Recharge light is amber indicating recharging while battery level indicates full Battery status reading is incorrect during recharge Battery Level indicators are only accurate when the XPower Powerpack has been disconnected from all appliances and all charging sources for fifteen minutes Allow Recharge cycle to go into Ready mode Unplug the charging sources and any appliances and let the XPower Powerpack rest for 15 minutes to get an accurate reading 39 Troubleshooting Reference Table 4 Troubleshooting reference Problem Possible Cause Solution Recharge light The voltage at the AC Continue to charge the XPower is still amber and not green after 40 hours wall outlet is less than 120 volts AC Powerpack for another 15 hours The battery will be fully charged even if the Rec
21. fter each use See Recharging the XPower Powerpack Battery on page 26 Using the Air Compressor XPower Powerpack 300 Plus Using the Air Compressor XPower Powerpack 300 Plus CAUTI ON The compressor is designed for short term operation only Operating the compressor over an extended period of time will cause the compressor unit to overheat and may cause damage Allow the compressor to cool down for 10 minutes after each 10 minutes of continuous operation CAUTION Do not leave the compressor unattended while in operation Keep out of reach of children CAUTI ON Do not overinflate article Follow the manufacturer s recommended pressure on tires and sports equipment Inflating Tires To inflate your vehicle motorcycle or bicycle tires 1 Place the valve connector securely on the tire valve stem and close the thumb latch Turn the compressor on and inflate your tire to the recommended pressure CAUTI ON Allow the compressor to cool down for 10 minutes after each 10 minutes of continuous operation 3 Turn the compressor off after appropriate pressure is reached 21 Using the Air Compressor XPower Powerpack 300 Plus 4 Open the thumb latch and remove the valve connector from the valve stem 5 Check air pressure with a pressure gauge Note Leave the thumb latch in the open position for storing to relieve pressure on the internal mechanism Inflating Small Sport
22. gen gas which can be ignited by sparks from electrical connections When working on electrical equipment always ensure someone is nearby to help you in an emergency WARNING Heated surface Ensure at least 2 inches 5 cm air space is maintained on all sides of the XPower Powerpack During operation keep away from materials that may be affected by high temperatures such as blankets pillows and sleeping bags CAUTI ON The jump start feature is designed for short term operation only less than 4 seconds Operating the jump start feature for more than 4 seconds may cause damage to the unit Allow the XPower Powerpack to cool down for 3 4 minutes after each jump start CAUTI ON XPower Powerpack 300 Plus The compressor is designed for short term operation only Operating the compressor over an extended period of time will cause the compressor unit to overheat and may cause damage Allow the compressor to cool down for 10 minutes after each 10 minutes of continuous operation Precautions When Working With Batteries Precautions When Working With Batteries WARNING Explosion and Fire Hazard 1 Follow all instructions published by the battery manufacturer and the manufacturer of the equipment in which the battery is installed Make sure the area around the battery is well ventilated 3 Never smoke or allow a spark or flame in vicinity of the engine or batteries 4 Be careful not to drop a me
23. harge light is still amber of charging The The valve connector Check that the valve connector is compressor may not be securely securely placed on the valve stem runs but won t inflate placed on the valve stem before closing the thumb latch XPower Powerpack The item being Check that the item being inflated 300 Plus only inflated may have a has no leaks leak Check the compressor hose for any breaks or leaks at connections The The compressor may Turn off the compressor and let it compressor have overheated from cool down runs slowly excessive use XPower Check the condition of the internal Powerpack Battery voltage is too battery The battery may need to be 300 Plus only low recharged or replaced The engine XPower Powerpack Recharge the XPower Powerpack being jump battery is not fully battery started will not Start 40 charged The engine condition is poor The engine start capacity exceeds the XPower Powerpack jump start capability Have the engine serviced Specifications Electrical Specifications 12 Volt DC Section Internal battery type sealed AGM Absorbed Glass Mat lead acid Internal battery voltage nominal 12 VDC Internal battery capacity minimum 20 Ah Internal battery CCA rating 200 CCA DC Power Socket maximum continuous load 12 A with automatic reset Built in fluorescent lamp replaceable two 4 W bulbs
24. lied Jump Start Cables Important Closely follow these instructions for jump starting your vehicle as they are different from the instructions supplied with other jump start products or booster cables To jump start a vehicle or boat engine CAUTION UN The jump start feature is designed for short term operation only less than 4 seconds Operating the jump start feature for more than 4 seconds may cause damage to the unit Allow the XPower Powerpack to cool down for 3 4 minutes after each jump start Turn off the vehicle or boat ignition and all accessories 2 Engage the park or emergency brake and place the transmission in park for an automatic or neutral for a manual 3 Ifjump starting a boat engine purge the engine compartment and bilge of all fumes before jump starting 4 Connect the jump start cables to the jumper cable port on the left side of the XPower Powerpack 5 Position the XPower Powerpack on a flat stable surface near the battery and away from all moving parts of the engine 6 Connect the red positive clip of the jump start cables to the positive terminal of the engine battery The battery s positive terminal is usually larger in diameter than the negative terminal In most vehicles the battery s positive terminal has a red wire connected to it 19 Jump starting a Vehicle Engine 20 7 Connect the black negative clip of the jump start cables to the engine block
25. load has tripped AC appliance is rated less than 250 watts high starting surge has tripped the safety overload Use an AC appliance with a power rating less than 250 watts AC appliance may exceed the XPower Powerpack s surge capability Use an AC appliance with a starting surge within the XPower Powerpack surge rating AC appliance will not operate the audible alarm is sounding Battery has discharged to 10 0 volts Inverter has overheated due to poor ventilation or excessively warm environmental conditions Turn the AC Outlet On Off switch off and recharge the XPower Powerpack Turn the AC Outlet On Off switch off and allow the XPower Powerpack to cool for 15 minutes or more Clear blocked fan opening or remove objects covering the unit then restart the XPower Powerpack Move to a cooler environment Run time is less than expected Internal battery is not fully charged AC appliance power consumption is higher than expected Recharge using the AC Charger until Recharge indicator is green Check AC appliance power or wattage rating or current draw for 12 volt DC appliances and compare with Table 1 AC Appliances and Run Times on page 15 and Table 2 12 Volt DC Appliances and Run Times on page 18 37 Troubleshooting Reference Table 4 Troubleshooting reference Problem Possible Cause Solution Measured Use of an The modified sinewave MSW out
26. m I mportant Safety I nformation The XPower Powerpack generates a similar type of AC power as a normal household wall outlet Operating the XPower Powerpack incorrectly or misusing it may damage the equipment or create hazardous conditions for the user Important Before using your XPower Powerpack be sure to read and save these safety instructions Warnings and Cautions AN WARNING Shock hazard Keep Away from Children The XPower Powerpack generates the same potentially lethal AC power as a normal household wall outlet Do not insert foreign objects into the AC Outlet the DC Power Socket the Jumper Cable Port or the ventilation holes Do not expose this product to water rain Snow or spray Do not open the XPower Powerpack except to replace the internal battery Have a qualified technician complete any service work CAUTION Do not connect any AC appliance with the neutral conductor connected to ground to the XPower Powerpack Warnings and Cautions vi AN CAUTION Do not expose the XPower Powerpack to temperatures over 104 F 40 C AN WARNING Explosion hazard Do not use this product where there are flammable fumes or gases such as in the bilge of a gasoline powered boat or near propane tanks Do not use this product in an enclosure containing automotive type lead acid batteries These batteries unlike the sealed AGM battery in XPower Powerpack vent explosive hydro
27. m of the vehicle battery being The battery to be jump started boosted must have a terminal voltage of at least 4 volts in order to work with the XPower Powerpack Not Audible alarm inside the unit shown sounds in the event of overheating low battery protection and reverse polarity jump start connection Air Compressor XPower Powerpack 300 Plus only Air Compressor XPower Powerpack 300 Plus only Feature Description On Off switch turns the compressor unit on and off Pressure gauge shows the PSI Ib in Nozzle Adaptor Compartment Valve connector with connector cord Right Side View Right Side View Feature Description DC Power Socket can e Power 12 volt DC auto RV or marine appliances e Recharge XPower Powerpack from a 12 volt outlet in a vehicle using the DC Charging Cable AC Outlet On Off switch illuminates when switch is turned On AC Outlet is a standard 3 prong outlet supplying 115 volts AC power for running an AC appliance Charger Input Socket for use with the AC Charger supplied External replaceable fuse is a 40 amp 32 VDC automotive blade type fuse which is available at many automotive parts stores Left Side View Left Side View Feature Description Fluorescent lights illuminate for about 25 hours when the battery is fully charged Light On
28. maintains a temperature range of 32 F to 86 F 0 C to 30 C CAUTION Discharging the internal battery below 10 0 volts will damage the battery and shorten its life Obtaining a Replacement Battery Replacement batteries are available from stores that specialize in and have a selection of lead acid AGM Absorbed Glass Mat batteries Refer to Table 3 for a listing of batteries approved for use with the XPower Powerpack Table 3 Approved Replacement Batteries Replacement Battery Where to Buy Panasonic Panasonic LC X1220P Tel 1 800 833 9626 12 V 20 Ah web www pasc panasonic com Digi Key Tel 1 800 344 4539 EnerSys EnerSys NPX 80 Tel 1 800 962 1287 Eastern US 12 V 20 Ah Tel 1 800 423 4667 Western US web www EnersysStationary com 31 Replacing the Internal Battery Replacing the Battery Read this entire section before disassembling the unit i WARNI NG Shock or Electrical Hazard Before attempting to replace the internal battery make sure e You disconnect any charging cables 12 volt DC appliances and AC appliances from the XPower Powerpack e You turn off the AC Outlet On Off switch and turn off the fluorescent light switch e You remove the jump start cables WARNING If you do not know how to safely remove and install batteries have this task performed by a qualified service technician WARNING AN When installing the replacemen
29. n Off switch to off and turn the fluorescent light switch off Plug the AC Charger into a standard AC wall outlet Insert the AC Charger cable end into the Charger Input Socket While the XPower Powerpack is recharging the Recharge indicator is amber If the battery is completely discharged a typical recharge may take up to 40 hours When fully charged the Recharge indicator changes to green and the XPower Powerpack is ready to use I mportant The 40 hour charging time for the XPower Powerpack assumes that there is 120 volts at the AC wall outlet If the voltage is less than 120 volts AC it may take more than 40 hours to fully recharge the XPower Powerpack If after 40 hours of charging the Recharge indicator is still amber and not green continue to charge the unit for another 15 hours The battery will be fully charged even if the Recharge indicator is still amber Once the battery is fully charged the charging voltage and current automatically reduces to a low maintenance level and the XPower Powerpack may be left permanently connected to the AC Charger If your utility power is interrupted the charging process automatically restarts when power returns CAUTI ON UN Do not operate AC or DC appliances while the XPower Powerpack is being recharged with the AC Charger The AC Charger may fail if AC appliances or 12 volt DC appliances are operated while the AC Charger is connected 27 Recharging the XPower Po
30. n their average rating when they are first switched on Although XPower Powerpack can supply momentary surge power up to 500 watts some appliances may exceed the capabilities of the XPower Powerpack and trigger the 15 Operating AC Appliances inverter s safety overload shutdown circuit See Troubleshooting Reference on page 36 for the reset procedure Trouble Appliances Some appliances may be damaged if they are connected to the XPower Powerpack See Precautions for Using Rechargeable Appliances on page viii Operating Several Appliances at Once You can run several AC appliances if the total rating of all the appliances in watts does not exceed 250 watts You can run appliances using an AC power bar Run time however will decrease accordingly with the number of appliances being operated and the AC power being consumed Operating an AC Appliance Before operating your AC appliance ensure that the battery of the XPower Powerpack is fully charged See Recharging with the AC Charger on page 13 for details To operate an AC appliance 1 Open the protective covering on the right side of the XPower Powerpack Turn the AC Outlet On Off switch to the On position The switch illuminates to indicate AC power is available at the AC Outlet 2 Plug the AC appliance into the AC Outlet and turn the appliance on XPower Powerpack will operate most devices rated up to 250 watts 3 Recharge the XPower
31. owerpack has been disconnected from all appliances and all charging sources for fifteen minutes Recharging with the AC Charger is a true plug in and forget charging method Xantrex recommends leaving the AC Charger connected when the XPower Powerpack is stored To recharge with the AC Charger 1 Disconnect any 12 volt DC appliances 2 Turn the AC Outlet On Off switch to Off and turn the fluorescent light off 13 Operating AC Appliances 3 Plug the AC Charger into a standard AC wall outlet Insert the AC Charger cable end into the Charger Input Socket The Recharge indicator changes from amber to green when charging is complete about 40 hours if the battery is completely discharged I mportant The 40 hour charging time for theXPower Powerpack assumes that there is 120 volts at the AC wall outlet If the voltage is less than 120 volts AC it may take more than 40 hours to full recharge the XPower Powerpack If after 40 hours of charging the Recharge indicator is still amber and not green continue to charge the unit for another 15 hours The battery will be fully charged even if the Recharge indicator is still amber Note Once fully charged the charging current automatically reduces to a maintenance charge mode and the XPower Powerpack may be left permanently connected to the AC Charger Operating AC Appliances Understanding AC Appliances AC appliances are rated by how much electrical powe
32. power supply filtering and may buzz slightly when powered by the XPower Powerpack The best solution to eliminate the buzzing is to use an audio system with a good quality filter Television I nterference The XPower Powerpack is shielded to minimize interference with TV signals If TV signals are weak you may see interference in the form of lines scrolling across the TV screen Try one of the following suggestions to minimize or eliminate the interference e Use an extension cord to increase the distance between the XPower Powerpack and the TV antenna and cables e Adjust the orientation of the XPower Powerpack television antenna and cables e Maximize TV signal strength by using a better antenna Use a shielded antenna cable where possible e Try a different TV Different models vary considerably in their susceptibility to interference Troubleshooting Reference Do not remove the cover of the XPower Powerpack or disassemble the XPower Powerpack except to replace the internal battery The XPower Powerpack does not contain any internal user serviceable parts and attempting to service the unit yourself could result in electrical shock or burn i WARNING Electric shock hazard 36 Table 4 Problem Possible Cause Troubleshooting Reference Troubleshooting reference Solution AC appliance will not operate the audible alarm is not sounding AC appliance rated more than 250 watts the safety over
33. put voltage average reading AC output of the XPower Powerpack is too low voltmeter to read requires a true RMS reading meter output voltage such as the Fluke 87 series for accurate measurement Battery is almost fully Press Battery Status button to verify discharged battery status and recharge the XPower Powerpack as necessary Battery Level indicators are only accurate when the XPower Powerpack has been disconnected from all appliances and all charging sources for fifteen minutes The battery No voltage is present Connect battery clips of the jump clips of the at the battery clips of start cable correctly to an external jump start the jump start cable battery cables measure unless they are zero volts properly connected to an external battery Charging light No AC power at the Ensure power is available at the wall is Off when wall receptacle receptacle AC Charger is connected AC Charger is faulty Replace the AC Charger Overload Appliance power Unplug the appliance and confirm shutdown requirements exceed that the appliance s power 38 the capability of the XPower Powerpack requirement is 250 watts or less before attempting to restart the appliance Troubleshooting Reference Table 4 Troubleshooting reference Problem Possible Cause Solution Extreme Appliance power Replace the fuse with a 40 A 32 overload 40 amp external requirements greatly exceed the capability VDC automotive blad
34. r in watts they consume XPower Powerpack can power most appliances within its rating 250 watts 2 1 amps Some appliances may be damaged if they are connected to the XPower Powerpack See Precautions for Using Rechargeable Appliances on page viii Some appliances may be difficult or impossible to operate from the XPower Powerpack They may have high surge requirements or should not be run from the XPower Powerpack See High Surge Appliances on page 15 14 Run Time on Typical AC Appliances Operating AC Appliances Note The fewer watts an AC appliance uses the longer the XPower Powerpack will operate before recharging is required Typical AC appliances that can be used on the XPower Powerpack are listed in Table 1 Table 1 AC Appliances and Run Times AC Appliance Watts Hours Cordless telephone stand by 5 40 Home security system 5 40 Clock radio 8 22 Portable stereo 10 17 Fluorescent work light 14 10 Fireplace fan 20 8 Laptop computer 25 6 Table lamp 40 3 Color TV 13 inches 60 2 5 1 Represents actual power consumption as measured on sample appliances 2 Operating times assume a fully charged battery and may vary based on mode brand of product High Surge Appliances The wattage rating of AC appliances is the average power used by the appliance Appliances such as televisions computer monitors and appliances with motors consume much more power tha
35. rpack 300 Plus only 6 Right Side View 7 Left Side View 8 Accessories 9 3 Operation Operating Conditions and Guidelines 11 Choosing a Location 12 Using XPower Powerpack for the First Time 13 Recharging with the AC Charger 13 Operating AC Appliances 14 Understanding AC Appliances 14 Contents Operating an AC Appliance 16 Operating 12 Volt DC Appliances 17 Jump starting a Vehicle Engine 19 Using the Air Compressor XPower Powerpack 300 Plus 21 Inflating Tires 21 Inflating Small Sports Equipment 22 Connecting to an External Battery 23 4 Maintenance Battery Maintenance 25 Recharging the XPower Powerpack Battery 26 Recharging with the AC Charger 27 Recharging with the DC Charging Cable 28 Recharging with a Generator s Regulated 12 Volt DC Outlet 29 Recharging From a Solar Panel 30 Replacing the Internal Battery
36. rvice xantrex com Web www xantrex com Returning a Product Returning a Product You must obtain a Return Material Authorization RMA number from Xantrex before returning a product directly to Xantrex When you contact Xantrex to obtain service be prepared to supply the following information e Serial number of your XPower Powerpack e Date of purchase e Information about the use of the XPower Powerpack If you are returning a product from the USA or Canada 1 Obtain an RMA number and a shipping address from Xantrex Products returned without an RMA number or shipped collect will be refused 2 Package the unit safely preferably using the original packing materials Include the following with your shipment e The RMA number e A copy of your dated proof of purchase e A return address where the repaired unit can be shipped e A contact telephone number e A brief description of the problem 3 Ship the unit to the address provided in Step 1 freight prepaid Xantrex recommends that you obtain proof of delivery 47 Out of Warranty Service How other laws apply This warranty gives you specific legal rights and you may also have other rights which vary from jurisdiction to jurisdiction For our Canadian customers When used herein implied warranties of merchantability and fitness for a particular purpose includes all warranties and conditions express or implied statutory or otherwise including without limit
37. s Equipment You can use the compressor to inflate small sports equipment such as balls soccer balls and footballs and small air mattresses CAUTION AN The XPower Powerpack cannot be used to inflate large capacity inflatables such as float tubes large air mattresses and inflatable boats These types of products require extended inflating times which may damage the compressor To inflate small sports equipment 1 Place the valve connector fully on or into the valve receptacle on the item Go to Step 4 OR If necessary use a supplied nozzle adaptor 2 Choose the appropriate nozzle adaptor insert the nozzle adaptor into the valve stem and close the thumb latch 3 Insert nozzle adaptor into the valve receptacle of the item 4 Turn the compressor on and inflate to appropriate pressure CAUTI ON Allow the compressor to cool down for 10 minutes after each 10 minutes of continuous operation 22 Connecting to an External Battery Turn the compressor off before removing nozzle adaptor from valve stem Remove nozzle adaptor from valve connector and store in storage compartment Note Leave the thumb latch in the open position for storing to relieve pressure on the internal mechanism Connecting to an External Battery You can extend battery operating times by connecting the XPower Powerpack to a larger external battery For example an external 60 amp hour battery gives approximately three
38. t uninterrupted operation of its products Xantrex shall not be 45 Warranty Information 46 liable for damages whether direct incidental special or consequential or economic loss even though caused by the negligence or fault of Xantrex Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you What will Xantrex do At its option Xantrex will repair or replace the defective product free of charge Xantrex will also at its option use new and or reconditioned parts made by various manufacturers in performing warranty repair and building replacement products If Xantrex repairs or replaces a product its warranty term is not extended Xantrex owns all parts removed from repaired products Service during warranty In order to qualify for the warranty a dated proof of purchase must be provided and the product must not be disassembled or modified without prior authorization by Xantrex If your product requires warranty service please return it to the place of purchase along with a copy of your dated proof of purchase If you are unable to contact your merchant or the merchant is unable to provide service contact Xantrex directly Phone 1 800 670 0707 toll free in North America 1 604 420 1585 outside of North America Fax 1 800 994 7828 toll free in North America 1 604 420 1591 outside of North America Email CustomerSe
39. t battery make sure the battery polarity is correct Reverse polarity will damage the XPower Powerpack and could cause serious injury 32 Replacing the Internal Battery To replace the battery 1 Place the XPower Powerpack upright on a stable level surface On the XPower Powerpack 300 unscrew the four fasteners on the battery cover Place the fasteners in the cover for safe keeping On the XPower Powerpack 300 Plus unscrew the four fasteners on the compressor unit Place the fasteners in the cover for safe keeping XPower Powerpack 300 XPower Powerpack 300 Plus Fasteners Fasteners 3 Disconnect the wires on the battery only I mportant Do not disconnect the wires on the main frame of the XPower Powerpack 4 After removing the old battery position the new battery close to the back of the XPower Powerpack Make sure the positive battery terminal is next to the red positive internal cable and the black negative terminal is next to the black negative internal cable Securely fasten the bolt washer and nut that holds the red positive cable to the positive battery terminal and the black negative cable to the negative battery terminal 33 Replacing the Fluorescent Tubes Do not overtighten the nut and bolt Consult the battery manufacturer for torque specifications On the XPower Powerpack 300 replace the battery cover and the four fasteners On the XPo
40. tal object on the battery or allow a metal tool to simultaneously touch the positive and negative cable ends or battery terminals It might spark or short circuit the battery or other electrical parts and cause an explosion 5 Remove personal metal items such as rings bracelets necklaces and watches when working with a lead acid battery A lead acid battery produces a short circuit current high enough to weld a ring or other similar objects to metal causing a severe burn 6 If you need to remove a battery always remove the positive terminal from the battery first Make sure all accessories are off so you don t cause an arc 7 Someone should be within range of your voice or close enough to come to your aid when you work near a lead acid battery 8 Have plenty of fresh water and soap nearby in case battery acid contacts skin clothing and eyes 9 Wear complete eye protection and clothing protection Avoid touching your eyes while working near batteries vii Precautions for Using Rechargeable Appliances 10 If battery acid contacts skin or clothing wash immediately with soap and water If acid enters your eye immediately flood it with running cold water for at least twenty minutes and get medical attention immediately 11 Keep a supply of baking soda on hand in the area of the batteries Baking soda neutralizes lead acid battery electrolyte Precautions for Using Rechargeable Appliances vill Most rechargeable
41. ut never overcharged To ensure safe recharging 25 Recharging the XPower Powerpack Battery and maximum battery life recharge the XPower Powerpack only with the Xantrex supplied chargers or approved battery chargers CAUTION AN Due to inherent self discharge lead acid batteries must be charged at least every 3 months especially in a warm environment Leaving a battery in a discharged state or not recharging every 3 months may result in permanent battery damage CAUTI ON Do not attempt to recharge the XPower Powerpack battery if it is frozen Gradually warm the frozen battery to 32 F 0 C before recharging Recharging the XPower Powerpack Battery To check the battery s charge level press the Battery Status button 26 Note Battery Level indicators are only accurate when the XPower Powerpack has been disconnected from all appliances and all charging sources for fifteen minutes You can recharge the battery using the fully automatic plug in and forget AC Charger the DC Charging Cable to recharge from your vehicle as you drive a generator equipped with a regulated 12 volt battery charging outlet a solar panel Recharging the XPower Powerpack Battery Recharging with the AC Charger Recharging with the AC Charger is a true plug in and forget charging method To recharge with the AC Charger 1 2 Disconnect any 12 volt DC appliances Turn the AC Outlet O
42. w This information will assist the service technician in diagnosing the problem quickly Serial number Purchase date Description of problem Has this problem happened before Appliances running when problem occurred Were any AC or 12 volt DC appliances affected Description of indicators on front panel 49 50 xantrex t 1 800 670 0707 toll free f 1 800 994 7828 toll free e CustomerService xantrex com www xantrex com
43. wer Powerpack 300 Plus replace the compressor unit and the four fasteners Dispose of the old battery in an environmentally responsible manner Replacing the Fluorescent Tubes To replace a fluorescent tube 1 2 Turn the light switch off Remove the clear cover by grasping it on each side at the top and pulling the top of the cover away from the unit Gently grasp the fluorescent tube and rotate 4 turn to remove it Insert the replacement tube and rotate turn to lock the tube in place Reattach the clear cover Replacing the External Fuse 34 The replacement fuse is a 40 amp 32 VDC car fuse which can be purchased at any automotive shop To replace the external fuse Open the protective cover on the right side of the unit Remove the fuse Insert the replacement fuse Ensure the replacement fuse is rated at 40 amps Troubleshooting Troubleshooting will help you identify the common problems than can occur with the XPower Powerpack Read this chapter before calling Xantrex Customer Service If you cannot solve the problem with the XPower Powerpack record the information asked for on Contacting Xantrex Customer Service on page 49 and then call Customer Service The information recorded on page 49 will help our Customer Service Representatives to assist you better 35 Common Problems Common Problems Buzz in Audio Equipment Some inexpensive stereo systems have inadequate internal
44. werpack Battery Recharging with the DC Charging Cable 28 Using the DC Charging Cable the XPower Powerpack can be recharged while you drive your vehicle I mportant Although the charge regulation circuitry in the XPower Powerpack does not operate with this charging method most vehicle voltage regulators will ensure that the XPower Powerpack is not overcharged CAUTION AN Do not use this recharging method if your vehicle has abnormally high voltage electrical systems that operate above 15 volts DC CAUTI ON AN Do not operate AC or DC appliances while the XPower Powerpack is being recharged with the DC Charging Cable from your vehicle To recharge the XPower Powerpack while you drive using the DC Charging Cable 1 While the vehicle engine is running plug one end of the DC Charging Cable into the DC Power Socket of the XPower Powerpack 2 Plug the opposite end of the DC Charging Cable into the vehicle s lighter socket or 12 volt accessory outlet 3 Once the XPower Powerpack is fully charged or if your vehicle s engine is not running disconnect the DC Charging Cable from both sockets Most of the XPower Powerpack s capacity will be restored in four hours while the vehicle engine is running Note The Recharge indicator will not illuminate when the XPower Powerpack is recharged through the DC Charging Cable Recharging the XPower Powerpack Battery Note Battery Level indicators
45. werpack has been disconnected from all appliances and all charging sources for fifteen minutes Front Panel Detail Feature Description Note Battery Status Button indicates Battery Level indicators are the charge state of the battery inaccurate if you press the Battery Status Button while the XPower Powerpack is running an appliance or is being recharged Recharge Indicator illuminates Recharging with the AC only when the battery is being Charger is a true plug in and recharged through the Charger forget charging method Input Socket and not through the Xantrex recommends leaving DC Charging Cable The lightis the AC Charger connected amber when charging and green when the XPower Powerpack when the battery is fully charged is stored Vehicle Jump Start Features e Reverse Polarity Alarm XPower Powerpack can detect sounds and the Battery Clips a reverse polarity condition Connected Improperly red caused by incorrectly light illuminates when the connecting the jump start jump start cables are cables to a battery and incorrectly connected to the automatically stops the flow battery terminals of current e Battery Clips Connected The jump start safety feature Properly green light prevents sparking at the illuminates if jump start cables battery terminals and prevents are correctly connected to the potential damage to your positive and negative terminals vehicle s electrical syste
Download Pdf Manuals
Related Search