X10 Wireless Technology TM751 Network Card User Manual
Contents
1. D5IP penea T D5IP WIRES o CAT 5 5i o9 ea x Ld SOURCE SOURCE o 0000 s D5RH SOURCES Figure 2 4 Basic System w Local Sources 4 Sources 4 Zones Local Sources 08905153B 12 Expanded 4 Source 8 28 Zone System D5XH Expansion Router Figure 2 5 shows an expanded system with four sources and ten zones with the addition of Local sources in four of the zones Each zone can have one local source The system is comprised of a D5RH Digital Audio Distribution Hub D5XH Expansion Hub D5KP Amplified Keypad D5IP Local source Wall Plates and Xantech XTC Speakers This configuration provides audio from each source into each zone as well as control of each source from each zone Zones with Local Sources have access to and control of those sources but the Local Sources are not available to other zones within the system This system can be expanded up to 28 zones using additional D5XHs Figure 2 5 Expanded System 4 Sources 10 Zones Local Sources 08905153B 13 3 Connections The D5RH is part of an integrated system that requires the use of other components Depending on the system design these components may include e D5KP Amplified Keypad at least one per zone required e D5IP Source Input Wall Plates one per zone where a Local Source is desired e D5XH Expansion Hub for systems2. 1 Basic 4 Source 4 Zone System 2 Basic 4 Source 4 Zone System Local Sources connected using D5IP Source Input Wall Plates 3 Expanded 4 Source 8 28 Zone System Local Sources connected using D5IP Source Input Wall Plates Basic 4 Zone 4 Source System Figure 2 3 shows a basic D5RH system with four sources and four zones The system is comprised of a D5RH Digital Audio Distribution Hub DBKP Amplified Keypad and Xantech XTC Speakers This configuration provides audio from each source into each zone as well as control of each source from each zone E S x ln E3 F3 SPEAKERS f 16 2 SPEAKER WIRES T Od dI D5KP 69 POWER SOURCES Figure 2 3 Basic System 4 Sources 4 Zones 08905153B E Basic 4 Zone 4 Source System w Local Sources Local Sources Connected Using DHIP Local Source Wall Plates Figure 2 4 shows a basic D5RH system with four sources and four zones with the addition of Local sources in two of the zones Each zone can have one local source The system is comprised of a D5RH Digital Audio Distribution Hub DBKP Amplified Keypad D5IP Source Input Wall Plates and Xantech XTC Speakers This configuration provides audio from each source into each zone as well as control of each source from each zone Zones with Local Sources have access to and control of those sources but the Local Sources are not available to other zones within the system SPEAKERS
3. The D5RH 4 Source 4 Zone Digital Audio Distribution Hub with DIGI 5 Technology and related products from Xantech provides the ability to listen to 4 different audio sources in up to 28 separate zones of the home all over CAT 5 wiring for total flexibility and convenience No need to have multiple audio systems in different areas just select a source from one of Xantech s premium in wall keypads sit back and enjoy Crystal Clear Digital Sound End to end digital architecture means that the entire signal path of the audio system remains in the digital domain from start to finish This means that noise signal loss and other unwanted effects are never present Each keypad contains a 30 Watt digital amplifier that allows the user to play music at loud volume when desired This also means that music at any volume is full and rich without distortion and with plenty of bass Simple Logical Installation A D5RH based system connects using CAT 5 and speaker wire making them reliable and easy to install Any digital or analog audio source can be connected directly to the D5RH Digital Audio Distribution Hub D5KP Amplified Keypads are connected to the D5RH using CAT 5 wiring inexpensive and reliable while speakers are connected to the DBKP Amplifier Keypad using traditional speaker wire This eliminates the need for multiple long runs of speaker wire streamlining the wiring process and slashing wiring costs Entertaining Possibilities The D5RH
4. Zone volume turned all the Increase volume way down 4 Speakers in room miswired or a Test known good speaker at defective or DBKP miswired D5KP speaker connector b Verify connections No audio from specific source Digital audio output not enabled Check setup menu and confirm digital audio output is enabled Multi channel digital audio Change digital Output to PCM formats 5 1 7 1 etc are not otereo supported by the D5IP D5RH etc Incorrect audio format selection Check RCA OPT COAX selection switch for proper selection 2 Digital source is outputting oelect PCM Stereo output on multi channel audio format 5 1 source component Consult 7 1 etc source s manual for details 3 Digital output not enabled on Enable digital output through source source s menu Set to PCM stereo Consult source s manual for details Hum or buzz through system 1 Ground loop Ensure proper grounding using speakers a three prong grounded AC outlet Re high Poor Audio quality 1 Clipping or distortion Adjust GAIN settings Speaker 3 Incorrect assignment of Isolate to source or room and left right source RCA cables or correct speaker cables 08905153B 290 Appendix A Specifications 120 VAC 3 Amps Export 240VAC models also available 48kHz 24 Bit 94dB Input Sensitivity DIP Switch 3 amp 4 DOWN 2V rms 8 2dBu Frequency Response 20Hz 20kHz 0 1dB Dimensions H x W x D w feet 2 3 8
5. settings etc please consult the D5XH Installation Manual it of Chassis Max of Zones A 1 D5RH sd 4 1 D5RH 1 D5XH 1 1 1 D5RH 2 D5XH 1 D5RH 3 D5XH 1 D5RH 4 D5XH ZoneX4 Local Source i 1 Per Zone Sources X 4 wig pe mm Audio Calbes E E Cat 5 m Local Source k 1 Per Zone i BI rr Cat 5 a PO Eel Audis IR Emitters Calbes n Cat 5 e eccccccccccoc e eeccsscccccsoecccsscccsccccscccseqiReessecceeccsosssosccosccsccsossssssssoessosscsssscssssscccssssoscocsscscssccssscsscscccsscsoscccssccccscccsccccsccccsccscccscccs a Aan A A Tr Z X6 9 04 6 0 O LE oo CET one oino IG y UN GOON Oo DA hs A L L J Local Source 1 Per Zone i o J r P m Cat 5 ZoneX6 Local Source 1 Per Zone 1 gE m CCIC i m Cat 5 OCGA m 4 L d M X6 M Local Source ai a i i 1 Per Zone o u i m Cat 5 D5XH D5XH 08905153B 26 Connections between a D5RH chassis and D5XH Digital Audio Distribution Hub involve CAT 5 patch cables routed between the units All cables are included with the D5XH Connections are required for e EXPANSION OUT EXPANSION IN e SOURCE LOOP OUT SOURCE LOOP IN EXPANSION OUT EXPANSION IN simply connect a CAT 5 patch cable from the DBRH s EXPANSION OUT port to the first D5XH s EXPANSION IN port For multiple D5XH units connect a CAT 5 patch cable from the first D5XH s
6. tune to a station etc Select the Source 3 or 4 from the zone s D5KP Amplifier Keypad Adjust the zone s volume to a normal comfortable listening level oelect SOURCE 1 and then SOURCE 2 and compare the levels to SOURCE 3 and or SOURCE 4 Un WG NO NS If the analog source s are playing at a softer volume than the other sources position the DIP switch for that source to the BOOST UP position 7 Observe the CLIP LED on the front of the D5RH If it lights up constantly or consistently the source s output level is too high and needs to be adjusted In this case position the appropriate DIP switch to the DEFAULT DOWN position 8 Repeat this process for the other analog source T BOOST DEFAULT Ter salsa s3ls4 ANALOG SOURCE INPUT GAIN ON ZONE PAIRING The ZONE PAIRING DIP switches allow each of the zones to be paired or grouped with any other zone Any zone that is in the UP position will be paired with any other zone that is also placed in the UP position This feature is useful to create large party zones where combined areas of the house share audio and system control T PAIRED V UNPAIRED ZONE PAIRING 08905153B 28 5 Troubleshooting Table 5 1 provides troubleshooting information for the D5RH Digital Audio Distribution Hub Audio Possible Cause No audio present in a specific 1 Source not playing Press Play turn ON etc zone 2 Zone not ON Press Power on the D5KP 3
7. AVAILABLE to the other zones of the system Both audio and IR control capabilities are available to Local Sources through the D5KP A zone may have a maximum of one Local Source 08905153B 22 D5IP Source Input Wall Plate A D5IP Source Input Wall Plate is required to add a Local Source to a zone The wall plate has audio and IR connections similar to the SOURCE INPUT of the D5RH A run of CAT 5 terminated to T 568A standard see Figure 2 2 is required between the D5KP Amplified Keypad and the location designated for the D5IP Connections between a source component and the D5IP are detailed in Figure 3 10 to Figure 3 12 while connections between the D5IP and the D5KP Amplified Keypad are detailed in Figure 3 15 NOTE Set RCA OPT COAX switch to RCA up position D5IP Front Stereo RCA Patch Cables Audio Source Analog Output OPTICAL In ACA i COAX Audio Source Digital Digital Optical Optical Output Cable DIGITAL 08905153B 23 D5IP Front Audio Source Digital Coaxial Output Digital Coaxial Cable COAX OPTICAL IN IN IR OUT A RCA coax IM Figure 3 10 to Figure 3 12 Local Source to D5IP Connections NOTE Multi channel digital audio formats 5 1 7 1 etc are not supported by the D5IP and D5RH However many audio video sources allow you to change the digital output to PCM Stereo In most cases this will allow multi channel audio sources t
8. containing from 5 to 28 zones each D5XH add up to six zones e Xantech Outdoor Ceiling and In Wall Speakers e Xantech IR Emitters and accessories This section describes the connectivity between these various components and the source audio components that comprise the system Each D5RH system is unique and not all connections will be made in every installation Important Safety Note Make sure that the D5RH is powered OFF before making any connections Source Audio Inputs The D5RH supports a total of four System Sources which are available to each of four zones and can be sent to up to a total of twenty eight zones using D5XH Expansion Hubs There are two types of Source Inputs Source 1 and 2 both have Digital Coaxial and Digital Optical connections source 3 and 4 both have three types of connectors Analog RCA Digital Coaxial and Digital Optical For each audio source that is connected use only one of these connection options Use stereo RCA type audio patch cables to connect an audio source to the D5RH s Source Input 3 or 4 as shown in Figure 3 1 Use this method for sources that do not have Digital Audio Outputs NOTE Make sure to put the COAX OPT RCA switch in the RCA down position Audio Source Analog Output Stereo RCA Patch Cables Figure 3 1 Source Input Analog 08905153B 14 Q Coaxial DIG COAX Use a Digital Coaxial cable to connect an audio source with a Digital Coaxial outp
9. s Whole House Music and Zone Grouping features make entertaining more fun than ever Fully customized audio options allow for control of the entire house from one location and also allow for the creation of multiple zone linking where groups of zones work together in party mode Control for Parents The Source Lock Out feature allows you to disable specific sources in the kid s rooms that you don t want them to access About DIGI 5 Technology DIGI 5 is a revolutionary new technology standard that provides a complete end to end digital audio solution over CAT 5 wiring DIGI 5 is based on advanced digital distribution and amplification circuits that allow multi room audio systems to be installed quickly and cost effectively DIGI 5 is a collaboratively developed technology that is licensed by the Linear Home Technology Group and is being initially integrated on a Linear group wide basis targeted to expand market and consumer acceptance of such systems 08905153B FA Features e 4 Source 4 Zone Capacity e Expandable up to 28 Zones with Optional D5XH Digital Audio Distribution Expansion Hub e End to End Digital Architecture for Crystal Clear Sound with No Signal Loss e Simple CAT 5 Wiring requirements e Innovative D5KP Amplified Keypad not included e Provide Custom Control Options e No PC Software Required For Setup Simply plug in the D5KP and go e Optional DBMR Mini Remote and D5LR Advance Learning Remote for added control featur
10. sources 9 ALL IR OUT Port Non source specific IR port Page Doorbell Trigger Input Interface with Page Doorbell system 11 Analog Source Input Gain Adjust Input GAIN from digital sources to avoid owitches distortion USB Port For firmware updates Clip Indicators Displays clipping from sources Zone Pairing Switches Links multiple zones 15 Auxiliary Power Output Port Provides additional power to DSKP Amplifier Keypads Zune OUPO Connect to D5KP Amplifier Keypads located in each zone Plug into 110VAC wall outlet Export 240VAC Pr OW CE ONNE models also available RS232 Port RS232 Communication Port Table 1 2 Rear Panel 08905153B 7 2 System Design Overview Applications Planning Before installing the D5RH it is essential to have a detailed and accurate system design The first step to a good design is to map the system It is advisable to mark up a copy of the house floor plan with speaker keypad and equipment locations etc Make sure that all locations are decided upon before pre wiring so that all necessary wiring and installation hardware is in place It is essential that ALL system components are accounted for prior to the pre wire stage After establishing design goals make a detailed list of all components Include source equipment keypad expansion hubs local source wall plates IR emitters etc Local Source TENE Speakers o0 CAT 5 BB 16 2 Speaker Wire Sources Audio
11. Cables O OOo Speakers Local Source CAT 5 FS 16 2 Speaker Wire Figure 2 1 System Wiring Overview 08905153B a Pre Construction In a pre construction installation walls and ceilings are open with no drywall installed This is desirable and allows the installer greater access than in retro fit applications Before actually running any wire or cable take the time to look around each room or area of the house and plan your wire paths for maximum efficiency Look for routes through uncluttered parts of the stud wall or ceiling that allow you to group all low voltage video speaker wires CAT 5 telephone etc wires wherever possible It is a good practice to label both ends of all cables and to protect wires by tying a plastic bag over the ends Note Do not run low voltage wires closer than 12 from high voltage wires If necessary cross low voltage wires at a 90 angle to prevent interference Retro Fit Wiring Post Construction Retro fit installations are more difficult to complete than pre construction because walls and ceilings are intact Typically wires must be fished into position through walls floors and ceilings Holes must be cut soeakers mounted directly in the ceiling or walls with no rough in brackets and keypads and local source wall plates must be mounted in existing drywall 08905153B 9 eee Pre Wiring D5RH Digital Audio Distribution Hub to D5BKP Amplifier Keypad The D5RH and all assoc
12. EXPANSION OUT port to the next D5XH s EXPANSION IN port and so on See Figure 3 15 for details SOURCE LOOP OUT SOURCE LOOP IN Connect a CAT 5 patch cable from each SOURCE LOOP OUT of the D5RH to each corresponding SOURCE LOOP IN on the first D5XH For multiple D5XH units connect a CAT 5 patch cable from each SOURCE LOOP OUT of the first D5XH to each corresponding SOURCE LOOP IN on the next D5XH and so on See Figure 3 15 for details D5RH CIIM SOURCE LOOP OUT 3 Cat 5 IN OURCE LOOP OUT EXPANSION 3 EXPANSION J QUT EXPAINSION EXPANSION J UT To Additional D5XH Chassis Figure 3 15 System Expansion Connections 08905153B safe 4 Settings amp Operation DIP Switch Settings There are two groups of DIP switches on the rear panel of the D5RH that must be set prior to operation e SOURCE INPUT GAIN e KEYPAD PAIRING ANALOG SOURCE INPUT GAIN Analog Audio SOURCE 3 and 4 have a corresponding DIP switch to adjust the input level relative to the other sources Once all connections are made the Analog Audio Source should be adjusted for clipping distortion before the installation is completed To adjust ANALOG SOURCE INPUT GAIN DIP switches Ensure that the Analog Audio Source is connected properly to SOURCE 3 or 4 Power up each source and turn on an audible signal Press PLAY
13. Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help CAUTION Changes or modifications not expressly approved by Xantech could void the user s authority to operate the equipment Caring For the D5RH Clean only with a dry soft cloth It is important to properly care for your D5RH Digital Audio Distribution Hub Follow these guidelines to ensure your device is preserved and protected e Do not expose the D5RH to rain liquids or moisture for an extended period of time e Do not expose the D5RH to temperature extremes e Do not place any objects on top of the D5RH to prevent chassis damage Operating Temperatures amp Environments Operating Temperature 32 104 F 0 40 C Humidity 0 9096 Precautions e Always exercise care when operating the D5RH Digital Audio Distribution Hub e Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat e Inthe unlikely event that smoke abnormal noise or strange odor is present immediately power the D5RH off Please report the problem to your dealer immediately e Never attempt to disassemble the D5RH You will lose any product warranty on the unit 08905153B Ec 1 Introduction Modern Convenience
14. dio sources to output a summed stereo signal through the digital output Consult the audio video source manual for details NOTE Some audio sources which utilize a digital output require that you enable the digital output before it will function If there is no audio present check the setup menu of the audio source to confirm that the digital output is enabled 08905153B 15 O Loop Outputs SOURCE LOOP OUT The Source Loop Outputs are used only when adding D5XH Expansion Hubs to the D5RH in order to create more than four zones These connectors carry Audio Status and IR information between the units and allow seamless functionality in all areas of the home with no complicated cross wiring splicing or specialized adapters needed When adding a D5XH Router simply connect CAT 5 Patch Cables from the SOURCE LOOP OUT of the D5RH to the SOURCE LOOP IN of the D5XH as shown in Figure 3 4 Complete connections for expanded systems are described in the section entitled Multi Chassis Connections D5RH Posner In SOURCE LOOP OUT Y 3 Cat 5 Ethernet Patch Cables D5XH Figure 3 4 Source Loop Outputs 08905153B 16 Q ET This connector is reserved for future implementation of two way data sources and communication Q o OUT Connect the CAT 5 Patch Cable from the DBRH EXPANSION OUT port to the D5XH EXPANSION IN port as shown Complete connections for expanded systems are described in the
15. es and remote operation Whole House Music Turns On All Zones to Same Source Zone Functions Do Not Disturb Source Lock Out Tone Control Balance Loudness Dynamic Range Compression DRC Local In Room Source Connectivity with Optional D5IP Source Input Wall Plates Paging DB Functionality w Optional Communications Controller Compact Single Rack Space Design Rack Mountable Optional Rack Ear Kit Available RM1UKIT D5RH Accessories D5XH 6 Zone Expansion Router D5KP Amplified Keypad D5IP Source Input Wall Plate D5MR Slim line Mini Remote D5LR Advance Learning Remote Control RM1UKIT 1U Rack Ear Kit Xantech Speakers 08905153B 5 Defining Terms Zone A Zone is defined as an area of the house that has separate source selection capabilities from all other areas of the house Typically a Zone is comprised of a single room but it is possible for a zone to spread across multiple rooms kitchen dining room master bedroom master bath or for multiple zones to be contained in one room game room bar area or multiple Zones in the yard Source A Source Is any audio or audio video device that is connected to the SOURCE INPUTS of the D5RH Any Source can be heard in any zone in the system Local Source A Local Source is an audio or audio video device that is connected to a D5IP Source Input Wall Plate Local Sources are able to be heard only in the zone in which they are installed and may not be heard in other zo
16. h shall have been repaired or altered by others than Xantech d to charges for installation or set up or adjustment of customer controls e to product that has suffered normal cosmetic deterioration f to product which shall have been subjected to negligence misuse abuse accident or damage by circumstances beyond Xantech s control including but not limited to lightning flood electrical surge tornado earthquake or any other catastrophic events beyond Xantech s control or g to product which shall have been subjected to improper operation connected equipment failure or malfunction inadequate packing or shipping damage maintenance or storage or to other than normal use of service The foregoing warranties do not cover reimbursement for labor transportation shipping removal installation or other expenses which may be incurred in connection with repair or replacement All claims for product shipping damage must be processes within 3 days of receipt by You A Xantech Return Authorization RA must be obtained from Xantech by You your installer or your distributor for Product covered under this warranty Covered product must be sent to Xantech together with proof of purchase RA number prepaid and insured to Xantech Freight collect shipments will be refused Risk of loss or damage in transit is borne by the sender Xantech s warranty does not cover Products which have been received improperly packaged altered or physically damaged Pr
17. iated components are wired using CAT 5 terminated to the T 568A Wiring otandard Figure 2 2 When pre wiring run lengths of CAT 5 from the pre determined equipment location the head end to each Amplifier Keypad location The CAT 5 routes all audio power IR and status information needed for full system operation Note For maximum performance over long runs more than 150 ft run an additional 16AWG 2 conductor wire for external power 12 34 56 78 lont T Nos LJ l EER e le e A KJ pay Fr ud ry e C ie N e e pu e r lo EL bat pa LJ ESI d e ES EE LLI I E ORANGE BLUE WHITE Shown tab down GREEN WHITE EIIE ORANGE WHITE BROWN WHITE Figure 2 2 T 568A Wiring Standard Amplifier Keypad to Speakers Run 16AWG 2 conductor stranded copper speaker wire between Amplifier Keypad locations and speaker locations Local Sources to Amplifier Keypad Local sources are only available within the area that they are installed They will not be available to other areas of the house as they are not distributed by the D5RH Run lengths of CAT 5 from any local in room source to the Amplifier Keypad located in that area 08905153B 10 Applications There are three typical system applications when installing the D5RH These options can be combined throughout a system depending on the design of the system
18. nes of the system Front Panel The front panel of the D5RH is populated simply by a Power LED and a Power Button Figure 1 1 and Table 1 7 provide descriptions and locations of Front Panel controls and indicators Figure 1 1 D5RH Front Panel Indicator Button Function LED Power LED Indicates Power ON OFF Status Red Power Button Turns System Power ON OFF Table 1 1 Front Panel 08905153B 6 Rear Panel The Rear Panel of the D5RH has connections for Power Source Inputs Zone Outputs IR Outputs Page Doorbell Trigger Input Auxiliary Power USB and Expansion capabilities as well as Digital Analog Source Selection Source Input Gain and Zone Pairing DIP Switches 13 18 gt ED mala EM UC 0n000 9 Daio Vi Ce Cy Cn ie 7 17 2 30 600 9 11 Figure 1 2 D5RH Rear Panel Conecor JjFuncion J Connect digital audio sources using Digital Digital Coaxial Audio Input Coaxial cable m Connect digital audio sources using Digital d Digital Optical Audio Input Optical cable Coaxial Optical RCA Selection select between Digital Coaxial Digital Optical Switch or RCA connection Analog Audio Input idea analog audio sources using RCA Expansion Port Control Status Link to D5XH Digital Audio Hub 6 Source Loop Outputs Audio Links to D5XH 7 D5 NET Port For future 2 way data sources amp communication m IR OUT Ports Source specific IR ports to control audio
19. o output a summed stereo signal through the digital output Consult the audio video source manual for details NOTE Some audio sources which utilize a digital output require that you enable the digital output before it will function If there is no audio present check the setup menu of the audio source to confirm that the digital output is enabled D5IP Side View D5KP Rear cece Ut dedi R SPEAKERS PWR IN Figure 3 13 D5IP to D5KP Connections 08905153B 24 IR OUT Connect a standard IR Emitter 283D emitter for example from the IR OUT port on the front of the D5IP to the IR receiver on the front of the audio source see Figure 3 14 For sources that have an IR Input port on the back of the unit use a 3 5mm to 3 5mm mono interconnect cable instead see Figure 3 14 D5IP Front D5IP Front Audio Source IR input 3 5mm Mono Interconnect Cable Figure 3 14 IR Out to Source Connections 08905153B 25 Adding Zones D5XH Digital Audio Distribution Hub A basic D5RH system can contain a maximum of four sources and four zones By adding D5XH Digital Audio Distribution Expansion Hub the system can contain a maximum of twenty eight zones Each D5XH expands the system by up to six zones while still maintaining a four source maximum limit This section details the connections required for adding D5XH Digital Audio Distribution Expansion Hub to a D5RH For detailed specifications
20. oducts will be inspected upon receipt Except as may be expressly provided and authorized in writing by Xantech Xantech shall not be subject to any other obligations or liabilities whatsoever with respect to equipment manufactured or sold by Xantech or services rendered by Xantech THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ATTENTION TO OUR VALUED CONSUMERS To insure that consumers obtain quality pre sale and after sale support and service Xantech products are sold exclusively through authorized dealers and authorized distributors The warranties on Xantech products are NOT VALID if the products have been purchased from an unauthorized dealer or distributor In order to determine if your Xantech re seller is authorized please call Xantech 800 843 5465 XANTECH PRODUCT WARRANTY DURATION go to Xantech com warranty for model numbers Hand Held Remote Controls 1 year Limited SPLCD Product 1 year Limited Source Components XIS100 1 year Limited Control Interfaces 2 year Limited 08905153B ETT Xantech Corporation 13100 Telfair Ave 2F Sylmar CA 91342 Xantech com Installation Instructions D5RH 2008 Xantech Corporation Document 08905153B This document is copyright protected No part of this manual may be copied or reproduced in any form without prior written consen
21. of the wire run Remove the terminal strip from the AUX POWER OUT connector on the D5RH Loosen the screws for the appropriate zone s terminal pairs on the terminal strip Insert the wires into the terminal strip paying close attention to polarity Tighten the screws on the terminal strip Remove the terminal strip from the PWR IN connector of the D5KP Loosen the screws on the D5KP s PWR IN terminal Insert the wires into the terminal paying close attention to polarity 10 Tighten the screws on the D5KP s PWR IN terminal 11 Connect the terminal strip back onto the AUX POWER OUT connector on the D5RH S CONAN KR s WN DSKP Rear D5RH AUX POWER OUT Figure 3 9 AUX POWER OUT Connections 08905153B 21 B USB Port USB IN The USB IN port is designed to allow upgrades to the D5RH s firmware D Power Connector Connect the supplied cord from the AC Power Connector into a properly grounded electrical outlet 18 RS232 Port Connect RS232 port to an external controller System Expansion The D5RH is capable of supporting up to four sources to up to four zones The system may be expanded in two ways e local Sources e Adding Zones Local Sources Each zone of a DBRH based system can have its own Local source connected directly to the zone s D5KP Amplified Keypad using a D5IP Source Input Wall Plate A source connected to a D5KP is accessible from the zone in which it is connected It is NOT
22. s 08905153B 18 QD OUT The ZONE OUT RJ 45 connector s interface with DBKP Amplified Keypad through CAT 5 cables wired to the T 568A Standard These connectors carry IR information from the keypad as well as audio information to the D5KP Amplifier Keypad Status information is also carried between the D5RH chassis and the Amplifier Keypads While a great deal of information is handled by the ZONE OUT connections the connections are straightforward Simply connect CAT 5 cables terminated to the T 568A configuration Figure 2 2 from each Amplifier Keypad to the corresponding ZONE OUT connector on the D5RH hub as shown in Figure 3 7 Note For wire runs up to 150 the CAT 5 connections are all that is necessary For wire runs over 150 use the AUX POWER OUT connectors as described in the section entitled Auxiliary Power Connector AUX POWER OUT D5KP Rear D5KP Rear D5RH amy ZONE Sia gege EENIA p t TET ET ES 2 4 J D5KP Heap D5KP Rear Figure 3 7 ZONE OUT Connections 08905153B 19 D5KP Speaker Connections The D5RH routes digital audio to connected D5KP Amplifier Keypad where the audio is then amplified and sent to in room speakers WARNING The D5KP s amplifier is capable of powering a single pair of 8 6 Ohm speakers DO NOT connect speakers with a rating of less than 6 Ohms DO NOT connect more than one speaker to either speaker connector of the D5KP In doing this damage to the D5KP may occ
23. section entitled Multi Chassis Connections D5XH D5RH IN SOURCE LOOP OUT EXPANSION CO 3 Cat 5 Ethernet Patch Cable EXPANSION EXPANSION 2 4 OUT OUT Figure 3 5 Expansion Outputs 08905153B 17 O OUT ALL IR OUT Xantech D5KP Amplified Keypad feature a built in IR Receiver that is used to control the sources connected to the D5RH using hand held remotes The four IR ports labeled 1 4 are Source Specific When a particular source is selected in a zone the corresponding IR port is active and only the selected source receives IR This allows for same branded or identical source components to be controlled discreetly from one location without conflict The ALL IR PORT is constantly active and passes IR information regardless of the source selected This is useful for sources that may need control no matter which source is active such as an A V Receiver or for applications utilizing an expanded IR network including IR Distribution devices such as Xantech s 791 44 Amplified IR Connection Block To make IR connections simply plug a standard 3 5mm IR emitter such as Xantech s 283D IR Emitter into the desired port If the source that is to be connected has an IR Input port a 3 5mm mini to mini interconnect cable can be used instead See Figure 3 6 for details Satellite 1 DVD Satellite 1 A V Receiver J gt o o o o 1 3 oooQ0 O O O CD CE Figure 3 6 IR Output
24. staller Ventilation The appliances should be situated so that their location or position does not interfere with their proper ventilation These appliances should never be placed near or over a radiator or heat register These appliances should not be placed in a built in installation such as a bookcase or cabinet that may impede the flow of air through the ventilation openings Non Use Periods Appliances that are left unattended and unused for long periods of time should be de energized Grounding or Polarization Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one blade wider than the other blade A grounding type plug has two blades and a third grounding prong The polarized wide blade and the third prong are provided for your safety If the provided plug does not fit your outlet consult an electrician for replacement of the obsolete outlet Power Cord Protection Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Water Do not use the apparatus near water Cleaning Unplug the apparatus from the power outlet before cleaning Use only a dry cloth to clean the apparatus Power Lines An outdoor antenna should be located away from power lines When installing an outside antenna system extreme care should be taken to avoid touching power lines or circuits as contact wi
25. t from Xantech Corporation Xantech Corporation shall not be liable for operational technical or editorial errors omissions made in this document 08905153B 32
26. th them may be fatal Object and Liquid Entry Never insert objects of any kind through the openings of these appliances as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Care should be taken so that objects do not fall and liquids are not spilled into the appliance through openings in the enclosure Servicing Do not attempt to service these appliances yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 08905153B 2 Damage Requiring Service These appliances should be serviced by qualified service personnel when A power supply connection or a plug has been damaged or e f liquid has been spilled into the appliance or objects have fallen into the appliance or The appliance has been exposed to water or moisture or The appliance does not appear to operate normally or exhibits a marked change in performance or The appliance has been dropped or the enclosure damaged Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or that have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards Safety Check Upon completion of any service or repairs to this audio product ask the service technician to perform safety checks
27. to determine that the audio product is in proper operating condition Lightning Storms Unplug this apparatus during lightning storms or when unused for long periods of time Attachments and Accessories Use only attachments accessories specified by the manufacturer Cart Stand Tripod Bracket or Table Use only with a cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Disconnect Device Where the mains plug or an appliance coupler is used as the disconnect device the disconnect device shall remain operable NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not in stalled and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e
28. ur and will void the products warranty To connect speakers to D5KP Amplifier Keypad 1 Ensure that system power is OFF Hemove the SPEAKER CONNECTOR from the D5KP Amplifier Keypad otrip speaker wire back 1 4 Loosen speaker terminal screws on the speaker connectors Insert speaker wires into terminals making sure to maintain polarity Tighten screws on speaker terminals Re connect the terminal strip to the SPEAKER CONNECTOR on the D5KP Amplifier Keypad Connect speaker wires to the room speakers maintaining correct polarity CON Oa W WH D5KP Rear Speaker AUX Power Connector Connector ooo R SPEAKERS 1 16AWG Speaker Wire To Speakers Figure 3 8 Speaker Connections 08905153B 20 gt 15M Power Connector AUX POWER OUT For wire runs over 150 it is recommended to run an additional 16 AWG 2 conductor wire from the head end location to the Amplified Keypad locations This will allow the AUX POWER OUT terminals to supply additional power to the Amplifier Keypads to compensate for the additional distance For wire runs over 300 16 AWG 2 conductor wire is required to operate the keypad The maximum wire run using CAT 5 and 16 AWG 2 conductor is 600 Make all connections between the D5RH and the D5KP Amplifier Keypad as previously described then make the aux power connections described below To make connections 1 Ensure that system power is OFF otrip the ends of the 16 AWG wire 1 4 on both ends
29. ut to the D5RH s Source Input as shown in Figure 3 2 NOTE Make sure to put the COAX OPT switch in the COAX up position Digital Connections provide the best audio quality and should be used if available If both a Digital Coaxial connection and a Digital Optical connection are present on the audio source use only one DO NOT connect both Coaxial and Optical outputs to the D5RH D5RH SOURCE INPUT 1 SOURCE INPUT 2 Digital Coax Digital Source Cable Digital Output Figure 3 2 Source Input Digital Coaxial O Optical OPTICAL Use a Digital Optical TOSLINK cable to connect an audio source with a Digital Optical output to the D5RH s Source Input as shown in Figure 3 3 NOTE Make sure to put the COAX OPT switch in the OPT down position Digital Connections provide the best audio quality and should be used if available If both a Digital Coaxial connection and a Digital Optical connection are present on the audio source use only one DO NOT connect both coaxial and optical outputs to the D5RH D5RH SOURCE INPUT 1 SOURCE INPUT 2 Digital Optical Cable Audio Source Digital Optical Output Figure 3 3 Source Input Digital Optical NOTE Multi channel digital audio formats 5 1 7 1 etc are not supported by the D5IP and D5RH However many audio video sources allow you to change the digital output to PCM Stereo In most cases this will allow multi channel au
30. x 17 x 14 1 8 8 6cm x 43 2cm x 35 9cm H x W x D w o feet 1 3 4 x 17 x 14 1 8 4 4cm x 43 2cm x 35 9cm Weight 19lbs 8 6kg Unit Weight 21lbs 9 5kg Shipping Weight 08905153B 30 Xantech Limited Warranty Effective for products sold after July 1 2006 Xantech Corporation Xantech warrants to the holder of a valid proof of purchase as the first end user purchaser You its products to be free from defects in materials and workmanship for the periods specified below from the date of purchase This limited warranty extends only to You for product purchased and used in the United States of America For product purchased outside of the United States of America You must contact the Xantech authorized distributor in your region for warranty services Product is not intended for end user installation If within the applicable warranty period above You discover such item was not as warranted above and You promptly notify Xantech in writing Xantech shall repair or replace the items at its option Xantech may elect which remedy or combination of remedies to provide in its sole discretion Xantech may use functionally equivalent reconditioned refurbished pre owned or new products or parts under this limited warranty This warranty shall not apply a to product which shall have been installed by other than an authorized Xantech installer b to installed product which is not installed to Xantech s specifications c to product whic
31. xantech INSTALLATION INSTRUCTIONS D5RH DIGI 5 DDS Digital Distribution System Rack Mount 4 Source 4 Zone Hub 08905153B m Safety Information WARNING 4 RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instruction in the literature accompanying the appliance WARNING TO REDUCE THE RISK OF FIRE OR SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE IMPORTANT SAFETY INFORMATION Read Information All the safety and operating information should be read before the appliance is operated Follow Information All operating and use information should be followed Retain Information The safety and operating information should be retained for future reference Heed Warnings All warnings on the appliance and in the operating instructions should be heeded Wall Mounting Mounting of this appliance should be done only by an authorized in
Download Pdf Manuals
Related Search