Whirlpool WHES48 Water System User Manual
Contents
1. Schedule recharge FIG 40 5 Press the button next to ON then press the RETURN button The display will go back to the screen shown in Figure 39 6 To return to the softener status screen press the RETURN tf button 12 34 PM l scheduled FIG 41 SETUP BUTTON The SETUP button on the softener status screen is used to set items of basic operating information e Set current time e Set water s hardness e Set recharge time e Set water s iron level e Advanced setup Accesses more items that can be set These are described starting on Page 19 e Set language SET TIME When the softener s electronic control is first powered up the setup procedure prompts you to set the cur rent time See Page 12 To change the time at a later date such as after a long power loss 1 Press the SETUP button on the softener status screen See Figure 42 12 34 PM Salt Recharge FIG 42 2 Press the SET TIME button See Figure 43 and the display will change to show the Set time screen See Figure 44 stame Set time LA 5 Setup menu FIG 43 FIG 44 3 Press the DOWN 4 or UP fT buttons to set the current time Hold the button down to rapidly advance Be sure AM or PM is correct unless sof tener is set for a 24 hour clock When the current time is shown press the RETURN tf button 4 To return to the softener status screen press the RETURN button2. For a period of two 2 years after installation labor to repair or replace any part deemed to be defective in materials or workmanship will be provided at no additional cost If during such respective period a part proves to be defective Warrantor will ship a replacement part directly to your home without charge After the second year labor necessary to maintain this product is not covered by the product warranty If you have questions regarding a warranted product need assistance with installation or troubleshooting wish to order a part or report a warranty issue we are just a phone call away SIMPLY DIAL 1 866 986 3223 Monday Friday 8 am 7 pm EST for assistance General Provisions The above warranties are effective provided the water softener is operated at water pressures not exceeding 125 psi and at water temperatures not exceeding 120 F provided further that the water softener is not subject to abuse misuse alter ation neglect freezing accident or negligence and provided further that the water softener is not damaged as the result of any unusual force of nature such as but not limited to flood hurricane tornado or earthquake Warrantor is excused if failure to perform its warranty obligations is the result of strikes government regulation materials shortages or other circumstances beyond its control THERE ARE NO WARRANTIES ON THE WATER SOFTENER BEYOND THOSE SPECIFICALLY DESCRIBED ABOVE ALL IMPLIED WARRANTIES
3. 16 Programming Your E Z Touch Water Softener SET HARDNESS When the softener s electronic control is first powered up the setup procedure prompts you to enter your water s hardness See Page 12 To change it 1 Press the SETUP button on the softener status screen See Figure 45 12 34 PM Salt Level 2 Press the RIGHT gt button to display the screen shown in Figure 46 Set hardness FIG 45 Setup menu FIG 46 FIG 47 3 Press the SET HARDNESS button and the display will change to show the Set hardness screen See Figure 47 4 Press the UP T or DOWN buttons to set the value for your water s hardness Hold the button down to rapidly advance When the correct hard ness is shown press the RETURN button NOTE Do not increase the hardness setting to com pensate for iron in your water The electronic control will compensate automatically after you set the iron level as described under Set Iron Level on this page 5 To return to the softener status screen press the RETURN button SET RECHARGE TIME Refer to Page 15 for instructions on setting the start time for automatic recharges SET IRON LEVEL The softener s electronic control can adjust cycle times to compensate for ferrous clear water iron in the water When the softener s electronic control is first powered up the iron level is set at 0 NOTE The iron level will always be displayed in ppm pa
4. O Whirlpool HOME APPLIANCES Model WHES48 How to install operate and maintain your E Z Touch Demand Controlled Water Softener Do not return water softener to store If you have any questions or concerns when installing operating or maintaining your water softener call our toll free number 1 866 986 3223 Monday Friday 8 AM 7 PM EST or visit www ecodynewatertreatment com When you call please be prepared to provide the model date code and serial number of your product found on the rating decal typically located on the rim below the salt lid hinges System tested and certified by NSF International against NSF ANSI Standard 44 for hardness reduction and efficiency System tested and certified by the Water Quality Association against CSA B483 1 Manufactured and warranted by Ecodyne Water Systems 1890 Woodlane Drive Woodbury MN 55125 Installation and Operation Manual Printed on recycled paper 7310359 Rev K 9 9 11 Product No W10270201 TABLE OF CONTENTS Page Specifications amp Dimensions 00 000 teeta 3 Water Softener Sately eo roae AEE Baath eg Gh Gal el Ea oP ne E ERA Ree BS oA a 4 Belore YOuUrStath eisie enean ee bahar tks Sad ieee e bo a E ees aed ee ee cece ae Sauteed 4 Inspect Shipments 3 4 ts ha ees Seat oes ht Aol Saeed Et ele ne As ee i lt Feta ete sd Bee ea 5 Water Conditionin
5. check your local codes See Air Gap Requirements and Valve Drain Requirements sections The water softener works on 24 volt 60 Hz electri cal power only supplied by a direct plug in trans former included Provide an electrical outlet within 10 feet in accordance with NEC and local codes Always install the water softener between the water inlet and water heater Any other installed water conditioning equipment should be installed between the water inlet and water softener See Figure 4 below Avoid installing in direct sunlight Excessive sun heat may cause distortion or other damage to non metallic parts PLUMBING CODES All plumbing must be completed in accordance with national state and local plumbing codes In the state of Massachusetts The Commonwealth of Massachusetts plumbing code 248 CMR shall be adhered to Alicensed plumber shall be used for this installation AIR GAP REQUIREMENTS A drain is needed for regeneration water See Figure 3 A floor drain close to the water softener is preferred A laundry tub standpipe etc are other drain options Secure valve drain hose in place Leave an air gap of 1 1 2 between the end of the hose and the drain This gap is needed to prevent backflow of sewer water into the water softener Do not put the end of the drain hose into the drain Drain Drain Hose Drain a Hose Hose ey K ate t 1 1 2 Ze
6. e Salt needs to be added e Time has been lost perhaps after a long power loss The Set Time screen will be displayed instead of the status screen e Error condition Service is required The flashing will stop after any key is pressed However it will start again at Midnight if the underly ing condition e g low salt level has not been addressed ALERTS amp REMINDERS Normally the current time is the only thing displayed along the top right portion of the screen A flashing message like the one shown in Figure 21 will be dis played instead if one of the following conditions occurs e Low salt indicates that salt needs to be added See Page 23 and the salt level indicator reset See Salt Level Button above This message appears whenever the salt level is 2 or below e Error Service is required 13 Programming Your E Z Touch Water Softener SET LANGUAGE When the softener s electronic control is first powered up the setup procedure prompts you to set the lan guage See Page 12 To change the language 1 Press the SETUP button on the softener status screen See Figure 22 12 34 PM Salt Level 2 Press the LEFT button to display the screen shown in Figure 23 FIG 22 Setup menu FIG 23 Select English language g Espa ol L Fran ais L FIG 24 3 Press the LANGUAGE button and the display will change to show the Select Language screen See Figure 24 4 Pre
7. 88 Switch is open Cam not rotating Advance valve Open Brine 07 34 FIG 87 Switch is closed Cam rotating Advance pg valve Closed Moving FIG 88 NOTE The following procedure shows the normal recharge cycle If the Clean feature is set to ON there will be an extra backwash and fast rinse before the normal regeneration sequence 1 Press the RECHARGE button on the softener s status screen 2 Press the RECHARGE NOW button to initiate a recharge The softener s valve advances from the service to fill position 3 Remove the brinewell cover and using a flashlight observe fill water entering the tank If water does not enter the tank look for an obstructed nozzle venturi fill flow plug brine tub ing or brine valve riser pipe 4 After observing fill press the ADVANCE VALVE button to move the softener s valve into the brine position A slow flow of water to the drain will begin Verify brine draw from the brine tank by shining a flashlight into the brinewell and observing a noticeable drop in the liquid level This may take 15 to 20 minutes NOTE Be sure water is in contact with the salt and not separated by a salt bridge See Breaking A Salt Bridge section If the water softener does not draw brine check for most likely to least likely Dirty or plugged nozzle and venturi see Cleaning the Nozzle and Venturi section Nozzle and venturi not seated on the gasket or g
8. FIG 80 To get access to the nozzle amp venturi remove the water softener s top cover Put the bypass valve s into the bypass position Be sure the water softener is in soft water service cycle no water pressure at noz zle amp venturi Then holding the nozzle amp venturi housing with one hand unscrew the cap Do not lose the o ring seal Lift out the screen support and screen Then remove the nozzle amp venturi disc gasket and flow plug s Wash the parts in warm soapy water and rinse in fresh water Be sure to clean both the top and bottom of the nozzle amp venturi disc If needed use a small brush to remove iron or dirt Do not scratch misshape etc surfaces of the nozzle amp ven turi Gently replace all parts in the correct order Lubricate the o ring seal with silicone grease and locate in place Install and tighten the cap by hand while supporting the housing Overtightening may break the cap or housing Put the bypass valve s into service soft water position Recharge the softener to reduce water level in the tank This will also assure that the softener is com pletely recharged and ready to provide softened water again Check the water level in the tank by looking down the brinewell If the water level does not drop after a recharge the problem has not been resolved Call 1 866 986 3223 Monday Friday 8 am to 7 pm EST 23 Troubleshooting AUTOMATIC ELECTRONIC DIAGNOSTICS This w
9. Maximum allowable inlet water pressure is 125 psi If daytime pressure is over 80 psi nighttime pressure may exceed the maximum Use a pressure reducing valve if necessary Adding a pressure reducing valve may reduce the flow If your home is equipped with a back flow preventer an expansion tank must be installed in accordance with local codes and laws The water softener works on 24 volt 60 Hz electrical power only supplied by a direct plug in transformer includ ed Be sure to use the included transformer and plug it into a nominal 120V 60 cycle household outlet that is in a dry location only grounded and properly protected by an overcurrent device such as a circuit breaker or fuse If transformer is replaced use only UL CUL or CSA approved Class 2 transformer with the following specifications Input 120 VAC 60 Hz 13 5 W Output Voltage 24 VAC Output Current 400 mA Do not use this system to treat water that is microbiologically unsafe or of unknown quality without adequate dis infection upstream or downstream of the system lt gt European Directive 2002 96 EC requires all electrical and electronic equipment to be disposed of accord tA ing to Waste Electrical and Electronic Equipment WEEE requirements This directive or similar laws are ae in place nationally and can vary from region to region Please refer to your state and local laws for proper as disposal of this equipment Do not return the water soften
10. in Figure 7 or if desired parts for a 3 valve bypass system not included can be purchased and assembled as shown in Figure 8 Bypass valves Pull out for Service Soft water ZL Push in for allow you to turn off water to the softener for mainte Bypass nance if needed but still have water in house pipes Pipe fittings must be 3 4 minimum TA FIG 7 Copper pipe Threaded pipe 3 VALVE BYPASS PEX Crosslinked Polyethylene pipe CPVC plastic pipe cA B Other pipe approved for use with potable water Bypass IMPORTANT Do not solder with plumbing attached to Valve installation adaptors and single bypass valve Soldering heat will damage the ie ja st adaptors and valve aye i y ave From Water To Water Softener Softener FIG 8 Installation Instructions Hard Water To Outside Faucets F Water Softener Valve He Plug in Transformer TN v To Controller Valve Drain Elbow Valve Drain Hose Do not connect the water softener valve drain tubing to the salt storage TYPICAL INSTALLATION Main Water pipe Conditioned Ground Water Clamp or e Ground a R Clamp Clips 1 NPT Sweat Adaptor not included N fe 1 NPT V Threaded Adaptor q Outlet Clip tank overflow hose Overflow Drain Elbow ubricated N Salt Storage O ring Tank Overflow Lo Hose EA e Single Bypass Valve Secure Valve D
11. may be underneath loose salt Take a broom handle or like tool and hold it next to the water softener Measure the distance from the floor to the rim of the water softener Then gently push the broom handle straight down into the salt If a hard object is felt before the pencil mark is even with the top it is most likely a salt bridge Gently push into the bridge in several places to break it Do not use any sharp or pointed objects as you may puncture the brine tank Do not try to break the salt bridge by pounding on the outside of the salt tank You may damage the tank Push Tool into Salt Bridge to Break Pencil Mark Broom Handle CLEANING THE NOZZLE amp VENTURI A clean nozzle amp venturi See Figure 80 is a necessity for the water softener to work properly This small component creates the suction to move brine from the brine tank into the resin tank If it should become plugged with sand silt dirt etc the water softener will not work and hard water will result Cap A3 y O ring Seal 0 Screen Support Flow Plug Nozzle amp Venturi Disc va Gasket C Pa Flow Plug HVDC _ C f Aa Housing Cone Screen Install with lettered side up concave side down Ferrule Nut IMPORTANT Be sure small hole in the gasket is cen tered directly over the small hole in the nozzle amp ven turi housing Be sure the numbers are facing up
12. switch NOTE The water heater is filled with hard water and as hot water is used it will refill with condi tioned water In a few days the hot water will be fully conditioned To have fully conditioned hot water immediately wait until the initial recharge is over Then drain the water heater following instructions for water heater until water runs cold SANITIZE THE WATER SOFTENER SANITIZE AFTER SERVICE 1 Open salt hole cover remove the brinewell cover and pour about 3 oz 6 tablespoons of household bleach into the softener brinewell Replace the brinewell cover 2 Make sure the bypass valve s is in the service open position 3 Start a recharge regeneration See Recharge Now on Page 15 4 After the recharge has completed fully open a cold water faucet downstream from the softener and allow 75 gallons of water to pass through the sys tem This should take at least 10 minutes Close the faucet 11 Water Softener Setup TOUCH SCREEN Controls for programming the water softener are dis played on a touch screen located on the softener s front panel See Figure 17 On screen buttons appear as rectangular outlines with rounded corners and change with each display See Figures below Button presses are acknowledged with a beep NOTE Before cleaning the touch screen to remove fingerprints unplug the transformer The con troller s memory items including clock tim
13. 106 7169180 Clip Drain 107 0900431 Hose Clamp 108 7271270 Drain Hose Adaptor 109 7170288 O Ring 15 16 x 1 3 16 110 0501228 Flow Plug 2 0 gpm 111 7170327 O Ring 5 8 x 13 16 112 7173024 O Ring 1 1 8 x 1 1 2 113 7174313 Bearing Wave Washer 114 7185500 Rotor amp Disc 115 7173032 O Ring 4 1 2 x 4 7 8 116 7185495 Rotor Seal 118 7171187 Plug Drain Seal 120 7089306 Clip 4 req 121 7271204 1 NPT Threaded Adaptor 2 req 122 7311127 O Ring 1 1 16 x 1 5 16 4 req 123 7094898 Turbine Support Key er 126 7081201 Retainer Nozzle amp Venturi 127 7195482 Seal Nozzle amp Venturi 128 7171145 Valve Body 129 7170319 O Ring 1 4 x 3 8 2 req 7081104 Housing Nozzle amp Venturi 1202600 Nut Ferrule 133 1148800 Flow Plug 3 gpm 7114533 Nozzle amp Venturi Gasket Kit 7204362 Gasket Only 135 7084607 Flow Plug 15 gpm 137 7167659 Screen Support 138 7170262 O Ring 1 1 8 x 1 3 8 4 7172997 Screw 10 x 2 5 8 8 req 44 7140738 Screw 4 24 x 3 4 2 req Nozzle amp Venturi Assembly incl 7253808 Key Nos 130 amp 132 139 Seal Kit incl Key Nos 111 112 7185487 115 116 117 amp 127 3479901 Adaptor Kit 1 to 1 1 4 E Not illustrated wo wo oO N _ wo R N _ A To order repair parts call toll free 1 866 986 3
14. 223 Monday Friday 8 am 7 pm EST Manufactured and warranted by Ecodyne Water Systems 1890 Woodlane Drive Woodbury MN 55125 Questions Call Toll Free 1 866 986 3223 Monday Friday 8 AM 7 PM EST or visit www ecodynewatertreatment com When you call please be prepared to provide the model date code and serial number found on the rating decal typically located on the rim below the salt lid hinges
15. 64 4 Press the RIGHT gt button to display the screen shown in Figure 67 EF Advanced setup Set salt type FIG 67 Sodium v Potassium L FIG 68 5 Press the SET SALT TYPE button and the display will change to show the Set salt type screen See Figure 68 6 Press the button next to the type of salt you will use When the correct salt type is checked press the RETURN button 7 To return to the softener status screen press the RETURN button twice 20 Customizing Features Options SET UNITS The softener can be set to display values such as vol ume and water hardness in either English or Metric units In addition the clock may be set to display time in either 12 hour AM PM or 24 hour format VOLUME UNITS To select between gallons and liters as volume units 1 Press the SETUP button on the softener status screen 2 Press the LEFT button twice to display the screen shown in Figure 69 setup FIG 69 3 Press the ADVANCED SETUP button The display will change to the following screen Additional features EF Advanced setup FIG 70 4 Press the RIGHT gt button twice to display the screen shown in Figure 71 seuns Set units E Advanced setup FIG 71 5 Press the SET UNITS button and the display will change to show the Volume units screen See Figure 72 Setup menu gallons v liters L on Volume units gt FIG 72 6
16. Button See Page 16 Set Time See Page 16 Set Hardness See Page 17 Set Recharge Time See Page 15 Set Iron Level See Page 17 Advanced Setup Additional Features Set Clean Feature See Page 19 Set Clean Time See Page 19 Set Salt Efficiency See Page 20 Set Salt Type See Page 20 Set Units See Page 21 Volume Units See Page 21 Time Format See Page 21 Hardness Units See Page 21 Set Contrast See Page 14 Restore Factory Settings See Page 22 Set Language See Page 14 SALT LEVEL BUTTON For the Low salt indicator to work whenever you add salt to the softener you must reset the salt level indicator on the display to match the new level of salt in the tank A decal on the brinewell shows numbers up to 8 corresponding to the numbers on the display Each press of the SALT LEVEL button See Figure 20 makes the level indicated on the display go up by one A Low salt message will flash on the display See Figure 21 whenever the level is 2 or below level is Salt indicated evel FIG 21 TANK LIGHT Touching the screen anywhere will turn on the light in the softener s brine tank The light will turn off again automatically after 4 minutes FLASHING BACKLIGHT The softener s display is backlit to make it easy to read The contrast may be adjusted as described on Page 14 The backlight will flash on and off when one or more of the following conditions occurs
17. Cut the drain line to the desired length and route it neatly out of the way IMPORTANT For proper operation of the water soften er do not connect the water softener valve drain tubing to the salt storage tank overflow hose Instructions AVE fe Electrical Shock Hazard Install metal ground clamp to metal house water supply pipe before beginning installation Securely tighten connection in center of metal ground clamp Failure to do so can result in death or electrical shock 10 Installation Instructions TEST FOR LEAKS To prevent air pressure in the water softener and plumbing system complete the following steps in order 1 Fully open two or more softened cold water faucets close to the water softener located downstream from the water softener 2 Place the bypass valve single or 3 valve into the bypass position See Figures 7 amp 8 on Page 7 3 Slowly open the main water supply valve Run water until there is a steady flow from the opened faucets with no air bubbles 4 Place bypass valve s in service or soft water posi tion as follows Single bypass valve Slowly move the valve stem toward service pausing several times to allow the water softener to fill with water 3 valve bypass Fully close the bypass valve and open the outlet valve Slowly open the inlet valve pausing several times to allow the water softener to fill with water 5 After about three minutes open a hot wa
18. INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED TO THE EXTENT THEY MIGHT EXTEND BEYOND THE ABOVE PERI ODS THE SOLE OBLIGATION OF WARRANTOR UNDER THESE WARRANTIES IS TO REPLACE OR REPAIR THE COMPONENT OR PART WHICH PROVES TO BE DEFECTIVE WITHIN THE SPECIFIED TIME PERIOD AND WAR RANTOR IS NOT LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES NO WARRANTOR DEALER AGENT REPRESENTATIVE OR OTHER PERSON IS AUTHORIZED TO EXTEND OR EXPAND THE WARRANTIES EXPRESS LY DESCRIBED ABOVE Some states do not allow limitations on how long an implied warranty lasts or exclusions or limitations of incidental or con sequential damage so the limitations and exclusions in this warranty may not apply to you This warranty gives you spe cific legal rights and you may have other rights which vary from state to state This warranty applies to consumer owned installations only Registered trademark TM Trademark of Whirlpool USA Manufactured under license by Ecodyne Water Systems Woodbury Minnesota 2009 Whirlpool Corporation All rights reserved 2 Specifications amp Dimensions Model WHES48 Model Code EZ 48 14 300 2 8 Ibs Rated Softening Capacity Grains Salt Dose 37 900 10 5 Ibs 48 000 18 1 Ibs Rated Efficiency Grains Pound of Salt Minimum Salt Dose 5 107 2 8 Ibs Water Used During Regeneration Minimum Salt Dose 3 0
19. Press the button next to the desired volume units and then press the RETURN button 7 To return to the softener status screen press the RETURN button twice TIME FORMAT To select between 12 hour AM PM and 24 hour time format 1 5 Go to the Volume units screen by following Steps 1 5 in Volume Units in the previous col umn 6 Press the RIGHT gt button to display the Time format screen See Figure 73 12 hour 24 hour L ES FIG 73 7 Press the button next to the desired time format and then press the RETURN TL button 8 To return to the softener status screen press the RETURN button twice HARDNESS UNITS To select between grains and ppm parts per million as water hardness units 1 5 Go to the Volume units screen by following Steps 1 5 in Volume Units in the previous col umn 6 Press the LEFT button to display the Hardness units screen See Figure 74 grains ppm _ or RET MESSING gt FIG 74 7 Press the button next to the desired hardness units and then press the RETURN button 8 To return to the softener status screen press the RETURN button twice 21 Customizing Features Options POWER OUTAGE MEMORY If electrical power to the water softener is lost mem ory built into the electronic control circuitry will keep all settings for up to six hours While the power is out the display is blank and the water soft
20. air gap zdi 1 1 2 air gap FLOOR DRAIN STANDPIPE LAUNDRY TUB FIG 3 THE PROPER ORDER TO INSTALL WATER TREATMENT EQUIPMENT Untreated Water to Outside Faucets Cold Water to House __ Hot Water to House Optional Sediment Filter Water Heater Softener a City Water Supply Pressure Tank OR ATN FIG 4 Installation Requirements VALVE DRAIN REQUIREMENTS 1 4 NPT l Thread Barbs for 3 8 Using the flexible drain hose included measure and y D Tubing cut to the length needed Flexible drain hose is not allowed in all localities check your plumbing codes If Hose Clamp local codes do not allow use of a flexible drain hose a O ee Disin Hose rigid valve drain run must be used Purchase a com Qn pression fitting 1 4 NPT x 1 2 in minimum tube and i FIG 5 1 2 tubing from your local hardware store Plumb a rigid drain as needed See Figure 6 NOTE Avoid drain hose runs longer than 30 feet l 1 4 NPT Compression Fitting Avoid elevating the hose more than 8 feet Clip Threads 1 4 NPT x 1 2 O D above the floor Make the valve drain line as Tube not included short and direct as possible Barbs Cut barbs from drain fit 1 2 Outside Dia ting pull clip to remove Copper Tube fitting from valve not included FIG 6 INLET OUTLET PLUMBING OPTIONS SINGLE BYPASS VALVE Always install either a single bypass valve provided as shown
21. asket deformed Valve seals leaking Restriction in valve drain causing a back pres sure bends kinks elevated too high etc See Install Valve Drain Hose section Obstruction in brine valve or brine tubing NOTE If water system pressure is low an elevated drain hose may cause back pressure stop ping brine draw 5 Press the ADVANCE VALVE button to move the softener s valve into the backwash position Look for a fast flow of water from the drain hose Check that the drain can adequately handle the flow and volume An obstructed flow indicates a plugged top distribu tor backwash flow plug or drain hose 6 Press the ADVANCE VALVE button to move the softener s valve into the fast rinse position Again look for a fast drain flow Allow the softener to rinse for a few minutes to flush out any brine that may remain in the resin tank from the brining cycle test N To return the softener s valve to the service posi tion press the ADVANCE VALVE button Need help troubleshooting Call Toll Free 1 866 986 3223 Monday Friday 8 AM 7 PM EST or visit www ecodynewatertreatment com When you call please be prepared to provide the model date code and serial number found on the rating decal typically located on the rim below the salt lid hinges 25 Softener Exploded View Valve Assembly See Pages 28 29 a for parts Softener Parts Lis
22. ater softener has a self diagnostic function for the electrical system except input power and or water meter The water softener monitors electronic com ponents and circuits for correct operation If a mal function occurs an error code appears in the display Error 1 FIG 82 A service person should be contacted to perform the diagnostics see below to further isolate the problem Procedure for removing error code from dis play 1 Unplug transformer from electrical outlet 2 Correct problem 3 Plug in transformer 4 Wait 6 minutes The error code will return if the problem was not corrected CHECKING THE TURBINE Use the following procedure to check the turbine that measures water flow through the softener 1 Press the INFO button on the softener s status screen to display the Water flow screen See Figure 83 a e 2 9 GPM z 3 FIG 83 2 Open a nearby soft water faucet There should be a non zero reading in the display with the faucet open 3 When water is flowing the Water used today screen See Fig 84 can be used to check the tur bine reading against volume of water exiting the softener Beginning when this screen is displayed a beep sounds with each gallon or liter as set pooogs d gallons Wat d FIG 84 OTHER INITIAL DIAGNOSTICS NOTE Be sure water is in contact with the salt and not separated by a salt bridge See Breaking A Salt Bridge section Other
23. d and press the NEXT but AM or PM is correct When the current time is ton The softener begins normal operation shown press the NEXT button described on the next page Questions Call Toll Free 1 866 986 3223 Monday Friday 8 AM 7 PM EST or visit www ecodynewatertreatment com When you call please be prepared to provide the model date code and serial number found on the rating decal typically located on the rim below the salt lid hinges 12 Programming Your E Z Touch Water Softener SOFTENER STATUS SCREEN During normal operation the softener s display shows a screen like the one in Figure 20 below The dis play automatically returns to this screen from other screens after 4 minutes of inactivity Indicates water flow 12 34 PM through the 5 Salt softener Level FIG 20 Indicates salt level in the salt storage tank During normal operation there are four active buttons on the softener s status screen They access sub sidiary screens used to control softener operations as shown below O Salt Level Button See Page 13 O Recharge Button See Page 15 Recharge Now See Page 15 Set Recharge Time See Page 15 Schedule Recharge See Page 16 O Info Information Button See Page 18 Water Flow See Page 18 e Average Daily Use See Page 18 Water Used Today See Page 18 Capacity Remaining See Page 18 Days In Use See Page 18 Total Recharges See Page 18 O Setup
24. dal and inorganically bound iron ferrous or ferric Ferrous clear water iron is soluble and dissolves in water This water softener will reduce moderate amounts of this type of iron see specifications Ferrous clear water iron is usually detected by taking a sample of water in a clear bottle or glass Immediately after taking the sample is clear As the water sample stands it gradually clouds and turns slightly yellow or brown as air oxidizes the iron This usually occurs in 15 to 30 minutes When using the softener to reduce Ferrous clear water iron add 5 grains to the hardness setting for every 1 ppm of Ferrous clear water iron See Set Water Hardness Number section Ferric red water and bacterial and organically bound irons are insoluble This water softener will not remove ferric or bacterial iron This iron is visible immediately when drawn from a faucet because it has oxidized before reaching the home It appears as small cloudy yellow orange or reddish suspended particles After the water stands for a period of time the particles settle to the bottom of the container Generally these irons are removed from water by filtra tion Chlorination is also recommended for bacterial iron Colloidal and inorganically bound iron is of ferric or fer rous form that will not filter or exchange out of water This water softener will not remove colloidal iron In some instances treatment may improve colloidal iron wate
25. done put a light coating of silicone grease on the single bypass valve o rings 5 Push the single bypass valve into the softener valve as far as it will go Snap the two large holding clips into place from the top down as shown in Figures 11 amp 12 IMPORTANT Be sure the clips snap firmly into place so the single bypass valve will not pull out Nozzle Top Cover Rae Brine Tank Seempy Overflow Nut Elbow Ferrule Salt f Hole Cover Brine Tank Overflow Grommet Brine 13 16 Hole Tubing Brinewell Salt Cover Storage a Brinewell Tank Stand Float Stem Tube SRO Brine K Valve gt FIG 10 Single Bypass Valve FIG 11 CORRECT ASSEMBLY Clip Q ZON Outside diameter Outside diameter of water softener of clip channel on valve inlet amp outlet single bypass valve FIG 12 NOTE Be sure all 3 tabs of the clip go through the matching holes on the water softener valve inlet or outlet and fully into the channel on the single bypass valve Make sure that the tabs are fully seated Installation COMPLETE INLET AND OUTLET PLUMBING Measure cut and loosely assemble pipe and fittings from the main water pipe to the inlet and outlet ports of the water softener valve Be sure to keep fittings fully together and pipes squared and straight Be sure hard water supply pipe goes to the water sof tener valve inlet side NOTE Inlet and outlet are marked on the water softener valve T
26. e water hardness etc are retained during brief power interruptions Use a microfiber towel or household cleaner safe for plastics on the touch screen FIG 17 SETUP PROCEDURE When the softener is plugged in for the first time a beep sounds and the display briefly shows E Z Senne Touch followed by the model number and software version 25 grains Next a series of three setup screens prompts you to FIG 18 enter basic operating information Select 3 WATER HARDNESS Press the UP T or DOWN em buttons to set the value of your water s hard Espanol language ness See Figure 18 then press the NEXT button NOTE Do not increase the hardness setting to com Fran ais L FIG 1 pensate for iron in your water The electronic G 15 control will compensate automatically after 1 LANGUAGE If the desired language is not N SEE OENE es PRSE on Page checked See Figure 15 press the button next to the desired language then press the NEXT button Setup correct Veg Set the time No L 12 00 PM FIG 19 FIG 16 4 If at this point you want to go back and make changes press the button next to NO then press the NEXT button to repeat the three setup screens 2 CURRENT TIME Press the DOWN J or UP T buttons to set the current time See Figure 16 5 If no changes are desired make sure the button Hold the button down to rapidly advance Be sure next to YES is checke
27. ed capacity while most often achieving maximum salt efficiencies When installing this unit in the State of California you MUST turn this feature ON To set this feature 1 Press the SETUP button on the softener status screen 2 Press the LEFT button twice to display the screen shown in Figure 63 setup 3 Press the ADVANCED SETUP button The display will change to the following screen Additional features Advanced setup 4 Press the ADDITIONAL FEATURES button 5 Press the LEFT button to display the screen shown in Figure 65 Set salt efficiency Setup menu zy Additi Arer FIG 65 FIG 66 6 Press the SET SALT EFFICIENCY button and the display will change to show the Set salt efficiency screen See Figure 66 FIG 63 FIG 64 7 Press the button next to ON to enable this feature or OFF to disable it and then press the RETURN L button 8 To return to the softener status screen press the RETURN button three times SET SALT TYPE Use this feature to program the electronic control with which type of salt you will use The default is Sodium Chloride NaCl Selecting Potassium Chloride KCI increases fill and brine rinse times To set this feature 1 Press the SETUP button on the softener status screen 2 Press the LEFT button twice to display the screen shown in Figure 63 3 Press the ADVANCED SETUP button to display the screen shown in Figure
28. ener will not regenerate When electrical power is restored the following will occur You have to reset the current time only if the display s backlight is flashing and the Set time screen is dis played instead of the softener s status screen Even if the clock is incorrect after a long power out age the softener operates as it should to keep your water soft However regenerations may occur at the wrong time of day until you reset the clock to the cor rect time of day NOTE If the water softener was regenerating when power was lost it will now finish the cycle RESTORE FACTORY SETTINGS This feature resets the softener s electronic controller to its initial startup condition All settings such as lan guage current time and water hardness are cleared and returned to their default values The user must then follow the setup procedure See Page 12 before the softener will be ready to run again 1 Press the SETUP button on the softener status screen 2 Press the LEFT button twice to display the screen shown in Figure 75 EZ setup Setup menu FIG 75 3 Press the ADVANCED SETUP button The display will change to the following screen features EF Advanced setup 4 Press the LEFT button to display the screen shown in Figure 77 Restore factory pa j settings Advanced setup FIG 77 FIG 76 Restore factory settings FIG 78 5 Press the RESTORE FACTORY SETTINGS button and the d
29. er to store If you have any questions or there are missing parts or damage please call Toll Free 1 866 986 3223 Monday Friday 8 am 7 pm EST or visit www ecodynewatertreatment com When you call please be prepared to provide the model date code and serial number found on the rating decal typically located on the rim below the salt lid hinges Inspect Shipment The parts required to assemble and install the water softener are included with the unit Thoroughly check the water softener for possible shipping damage and parts loss Also inspect and note any damage to the shipping carton Remove and discard or recycle all packing materials To avoid loss of small parts we suggest you keep the small parts in the parts bag until you are ready to use them Packing List Ground Clamp Bypass Valve Hose Clamps Adaptor Elbow 20 ft Drain Hose Grommet Installation Adaptors Water Hardness Test Strip FIG 2 Water Conditioning Information IRON Iron in water can cause stains on clothing and plumb ing fixtures It can negatively affect the taste of food drinking water and other beverages Iron in water is measured in parts per million ppm The total ppm of iron and type or types is determined by chemical analysis Four different types of iron in water are Ferrous clear water iron Ferric red water iron Bacterial and organically bound iron Colloi
30. g Information 0 a a Ea E eet 5 Installation Requirements 00 0c eee eee eee 6 7 Installation Instructions s siia eiei a 00 ce eee ee 8 11 Water Softener Setup 0 000 ccc ene eee 12 Programming Your E Z Touch Water Softener 0 0 00 00 eee eee 13 17 Retrieving Information from the Water Softener Management System 00 000 c eee eee 18 Customizing Features Options 1 0 0 0 eee tee ae 19 22 Routine Maintenance 0 0000 nents 23 Troubleshooting seci tei epi dda edd Sd i eae Wace ald dae A 24 25 Exploded View amp Parts List 0 0 00 ccc tenet eeeeee 26 29 WATER SOFTENER WARRANTY MODEL WHES48 Warrantor Ecodyne Water Systems 1890 Woodlane Drive Woodbury MN 55125 Warrantor guarantees to the original owner that For the lifetime of the original owner the salt storage tank and mineral tank will not rust corrode leak burst or in any other manner fail to perform their proper functions and that For the lifetime of the original owner the ion exchange resin will not fail to perform its proper function and that For a period of three 3 years after installation the electronic control board will be free of defects in materials and workmanship and will perform its normal functions and that For a period of two 2 years after installation all other parts will be free from defects in materials and workmanship and will perform their normal functions and that
31. gal 1 000 grains Total Water Used Per Regeneration Maximum Salt Dose 44 2 gallons Rated Service Flow Rate 11 9 gpm Amount of High Capacity lon Exchange Resin 1 33 cu ft Pressure Drop at Rated Service Flow 15 psig Water Supply Max Hardness 160 gpg Water Supply Max Clear Water Iron 12 ppm Water Pressure Limits minimum maximum 20 125 psi Water Temperature Limits minimum maximum 40 120 F Minimum Water Supply Flow Rate 3 gpm Maximum Drain Flow Rate 2 0 gpm Salt Storage Capacity 200 Ibs Capacity to reduce clear water iron is substantiated by WQA test data State of Wisconsin requires additional treatment if water supply contains clear water iron exceeding 5 ppm Canada working pressure limits 1 4 7 0 kg cm These systems conform to NSF ANSI 44 for the specific performance claims as verified and substantiated by test data The efficiency rating is only valid at the stated salt dose These softeners were efficiency rated according to NSF ANSI Standard 44 Variable Salt Dose The salt dose is selected by the electronic controls at regeneration time based on the amount needed 3 3 4 ry IN OUT Shear ry 47 7 8 41 1 2 39 1 2 y yY y FIG 1 Questions Call Toll Free 1 866 986 3223 Monday Friday 8 AM 7 PM EST or visit www ecodynewatertreatment com When you call please be prepared to provide the model date code and seria
32. information which may be beneficial in diagnos ing problems may be found in the Total recharges and Days in use information screens This informa tion is retained by the computer from the first time electrical power is applied to the electronic controller On the softener s status screen press the INFO but ton then the LEFT button to display these screens See Page 12 CHECKING THE MODEL CODE 1 Unplug the softener s transformer and plug it back in watching the touch screen display 2 After the E Z Touch screen displays briefly a screen that looks like Figure 86 will be shown for a few seconds Take note of the number next to the word Model E Z Touch FIG 85 Model EZ 48 Version W1 1 FIG 86 3 The correct code for Model WHES48 is EZ 48 This code identifies the softener model If an incor rect model code is displayed the softener will oper ate on incorrect configuration data 24 Troubleshooting MANUAL ADVANCE REGENERATION CHECK This check verifies proper operation of the valve motor brine tank fill brine draw regeneration flow rates and other controller functions Always make the initial checks first Use the following procedure to advance the water softener through the regeneration cycles to check operation In the following steps you will use the ADVANCE VALVE button to move the valve into each cycle and check correct switch operation See Figures 87 amp
33. isplay will change to show the Restore factory settings screen See Figure 78 6 Press the button next to YES and then press the RETURN button 7 Follow the setup procedure on Page 12 Routine Maintenance ADDING SALT Lift the salt hole cover and check the salt storage level frequently If the water softener uses all the salt before you refill it you will experience hard water Until you have established a refilling routine check the salt every two or three weeks Always add if less than 1 4 full Be sure the brinewell cover is on NOTE If using potassium chloride KCI do not fill above level 4 on the brinewell decal NOTE In humid areas it is best to keep the salt stor age level lower and to refill more often to avoid salt bridging Recommended Salt Nugget pellet or coarse solar salts with less than 1 impurities Salt Not Recommended Rock salt high in impurities block granulated table ice melting ice cream making salts etc BREAKING A SALT BRIDGE Sometimes a hard crust or salt bridge forms in the brine tank It is usually caused by high humidity or the wrong kind of salt When the salt bridges an empty space forms between the water and the salt Then salt will not dissolve in the water to make brine Without brine the resin bed is not recharged and hard water will result If the storage tank is full of salt it is difficult to tell if you have a salt bridge A bridge
34. l change to show the Set contrast screen See Figure 28 6 Press the UP fT or DOWN J buttons to increase or decrease the contrast When the preferred con trast is reached press the RETURN button To return to the softener status screen press the RETURN button twice N 14 Programming Your E Z Touch Water Softener RECHARGE BUTTON The long button at the bottom of the softener status screen See Figure 29 will show recharge status including whether a recharge is scheduled See Figure 41 During a recharge cycle a countdown clock is displayed in the button See Figure 32 RECHARGE NOW To manually initiate an immediate recharge 1 Press the RECHARGE button at the bottom of the softener status screen See Figure 29 12 34 PM 2 The display will change to show the following screen 7 pm Recharge FIG 30 options 3 Press the RECHARGE NOW button The recharge begins and display will change to show a recharge status screen like the one in Figure 31 Advance valve Closed 4 To return to the softener status screen press the RETURN button FIG 29 FIG 31 12 34 PM Recharging 112 45 FIG 32 SET RECHARGE TIME When the softener s electronic control is first powered up the default time for starting an automatic recharge is 2 00 a m This is a good time in most households because water is not being used To change the recharge ti
35. l number found on the rating decal typically located on the rim below the salt lid hinges 3 Water Softener Safety Your safety and the safety of others are very important We have provided many safety messages in this manual and on your appliance Always read and obey all safety messages This is the safety alert symbol This symbol alerts you to potential hazards that can kill or hurt you and others All safety messages will follow the safety alert symbol and either the word DANGER or WARNING These words mean Q You can be killed or seriously injured if you don t DAN G E R immediately follow instructions Y be killed ib siv injured it you don t AWARNING a All safety messages will tell you what the potential hazard is tell you how to reduce the chance of injury and tell you what can happen if the instructions are not followed In the state of Massachusetts The Commonwealth of Massachusetts plumbing code 248 CMR shall be adhered to A licensed plumber shall be used for this installation In the state of California You must turn the Salt Efficiency Feature setting to ON This may initiate more frequent recharges However it will operate at 4 000 grains per pound of salt or higher To turn on the Salt Efficiency Feature follow the instructions in the Salt Efficiency section of this manual Before You Start The water softener requires a minimum water flow of 3 gallons per minute at the inlet
36. me 1 Press the RECHARGE button on the softener sta tus screen See Figure 33 12 34 PM 2 The display will change to show the following screen L7 gt FIG 34 Press the RIGHT gt button The display will change to show the following screen Set recharge time 5 FIG 33 Recharge options ao 7 Rech m FIG 35 FIG 36 4 Press the SET RECHARGE TIME button and the display will change to show the Set recharge time screen See Figure 36 Press the UP T or DOWN 4 buttons to set the recharge time in 1 hour increments Hold the but ton down to rapidly advance Be sure AM or PM is correct unless softener is set for a 24 hour clock When the desired recharge start time is shown press the RETURN button The display will go back to the softener status screen a 15 Programming Your E Z Touch Water Softener SCHEDULE A RECHARGE To schedule a recharge for the next preprogrammed recharge time 2 00 a m or as set on Page 15 1 Press the RECHARGE button at the bottom of the softener status screen See Figure 37 12 34 PM 2 The display will change to show the following screen Recharge options FIG 37 lt 7 FIG 38 3 Press the LEFT button The display will change to show the following screen recharge lam Cerca FIG 39 4 Press the SCHEDULE RECHARGE button The display will change to show the screen in Figure 40
37. r Colloidal iron water usually has a yellow appearance when drawn After standing for several hours the color persists and the iron does not settle but remains suspended in the water SEDIMENT Sediment is fine foreign material particles suspended in water This water softener will not remove sedi ment This material is most often clay or silt Extreme amounts of sediment may give the water a cloudy appearance A sediment filter installed upstream of the water softener normally corrects this situation Water may contain one or more of the four types of iron and any combination of these Total iron is the sum of the contents Capacity to reduce clear water iron is substantiated by WQA test data Installation Requirements LOCATION REQUIREMENTS Consider all of the following when selecting an installa tion location for the water softener Do not locate the water softener where freezing temperatures occur Do not attempt to treat water over 120 F Freezing temperatures or hot water damage voids the warranty To condition all water in the home install the water softener close to the water supply inlet and upstream of all other plumbing connections except outside water pipes Outside faucets should remain on hard water to avoid wasting conditioned water and salt A nearby drain is needed to carry away regenera tion discharge drain water Use a floor drain laundry tub sump standpipe or other options
38. race the water flow direction to be sure hard water is to inlet IMPORTANT Be sure to fit align and support all plumb ing to prevent putting stress on the water softener valve inlet and outlet Stress from misaligned or unsupported plumbing may cause damage to the valve Complete the inlet and outlet plumbing for the type of pipe you will be using Secure ground clamp to metal pipes See Fig 13 INSTALL VALVE DRAIN HOSE 1 Measure cut to needed length and connect the 3 8 drain line provided to the water softener valve drain fitting Use a hose clamp to hold the hose in place NOTE Avoid drain hose runs longer than 30 feet Avoid elevating the hose more than 8 feet above the floor Make the valve drain line as short and direct as possible IMPORTANT If codes require a rigid drain line see Valve Drain requirements section 2 Route the drain hose or copper tubing to the floor drain Secure drain hose This will prevent whip ping during regenerations See Air Gap Requirements section INSTALL SALT STORAGE TANK OVERFLOW HOSE 1 Measure cut to needed length and connect the 3 8 drain line provided to the salt storage tank over flow elbow and secure in place with a hose clamp 2 Route the hose to the floor drain or other suitable drain point no higher than the drain fitting on the salt storage tank This is a gravity drain If the tank overfills with water the excess water flows to the drain point
39. rain Hose in place over Floor Drain i NOTE See Air Gap Requirements section pn ez Z 1 1 2 NOTE Water Softener shown with Salt Hole esv s e air gap Cover and Top Cover removed Floor Drain FIG 9 Installation Instructions TURN OFF WATER SUPPLY 1 Close the main water supply valve located near the well pump or water meter 2 Open all faucets to drain all water from house pipes NOTE Be sure not to drain water from the water heater as damage to the water heater ele ments could result INSTALL THE BRINE TANK OVERFLOW ELBOW Install the brine tank overflow grommet and elbow in the 13 16 diameter hole in the back of the salt storage tank sidewall NOTE The brine tank overflow elbow accepts either 1 2 or 3 8 I D hose MOVE THE WATER SOFTENER INTO PLACE AVE hfe Excessive Weight Hazard Use two or more people to move and install water softener Failure to do so can result in back or other injury 1 Move the water softener into the desired location Set it on a solid level surface IMPORTANT Do not place shims directly under the salt storage tank to level the softener The weight of the tank when full of water and salt may cause the tank to fracture at the shim 2 Visually check and remove any debris from the water softener valve inlet and outlet ports 3 Make sure the turbine assembly spins freely in the out port of the valve 4 If not already
40. rts per million regardless of whether the Hardness units setting is grains or ppm The conversion factor is 3 grains per ppm of clear water iron To enter your water s iron level 1 Press the SETUP button on the softener status screen See Figure 45 2 Press the RIGHT gt button three times to display the screen shown in Figure 48 Set iron level Setup menu FIG 48 FIG 49 3 Press the SET IRON LEVEL button and the display will change to show the Set iron level screen See Figure 49 4 Press the UP T or DOWN 4 buttons to set the value for iron in your water Hold the button down to rapidly advance When the correct iron level is shown press the RETURN L button 5 To return to the softener status screen press the RETURN button 17 Retrieving Information from the Water Softener Management System INFO INFORMATION BUTTON The INFO button on the softener status screen is used to look up the following information about the fe softener and its operations e Current water flow 2 9 GPM e Average daily water use gt e Water used today FIG 51 e Capacity remaining e Days in use e Total recharges To display one of these screens 1 Press the INFO button at the center of the softener A dail status screen See Figure 50 FIG 52 12 34 PM Salt t recos saron FIG 50 Water used ames FIG 53 2 Press the RIGHT gt or LEFT buttons to scroll through the six informa
41. ss the button next to the desired language When the desired language is checked press the OK button 5 To return to the softener status screen press the RETURN Tf button TO SET THE SOFTENER TO ENGLISH IF ANOTHER LANGUAGE IS DISPLAYED If the softener status screen is not showing press the RETURN button a few times On the sta tus screen press the PRGM button Press the LEFT button then press the large IDIOMA or LANGUE button Press the button next to ENGLISH then press the OK button Press the RETURN Tf button to return to the status screen SET CONTRAST The contrast of the softener s display screen may be adjusted to optimize its readability Depending on the ambient lighting conditions you may want to increase or decrease the contrast from the medium level that is the default when the electronic control is first powered up To change the contrast 1 Press the SETUP button on the softener status screen See Figure 22 2 Press the LEFT button twice to display the screen shown in Figure 25 setup e gt FIG 25 3 Press the ADVANCED SETUP button The display will change to the following screen Additional features amp Advanced setup 4 Press the LEFT button twice to display the screen shown in Figure 27 setcontast Set contrast Advanced setup Setup menu FIG 26 FIG 27 anil FIG 28 5 Press the SET CONTRAST button and the display wil
42. status screen press the RETURN button three times SET CLEAN TIME The length of the Clean Feature with Sediment Guard technology can be adjusted from 1 to 30 minutes The default value for this feature is 7 minutes To change the clean time 1 Press the SETUP button on the softener status screen Press the LEFT button twice to display the screen shown in Figure 57 Press the ADVANCED SETUP button to display the screen shown in Figure 58 Press the ADDITIONAL FEATURES button to dis play the screen shown in Figure 59 Press the RIGHT gt button to display the screen shown in Figure 61 Set clean time Additi I features FIG 61 FIG 62 Press the SET CLEAN TIME button and the dis play will change to show the Set clean time screen See Figure 62 Press the UP T or DOWN 4 buttons to set the clean time in 1 minute increments Hold the button down to rapidly advance When the desired clean time is shown press the RETURN button To return to the softener status screen press the RETURN button three times 19 Customizing Features Options SET SALT EFFICIENCY When this feature is ON the water softener will oper ate at salt efficiencies of 4000 grains of hardness per pound of salt or higher May recharge more often using smaller salt dosage and less water The sof tener is shipped with this feature set OFF which uti lizes the maximum rat
43. t 2 O Ring 13 16 x 1 1 16 3 Top Distributor 4 O Ring 2 3 4 x 3 Repl Bottom Distributor Filter Screen Clamp Section 2 req Retainer Clip 2 req Repl Resin Tank 10 x 40 0 Resin 1 cu ft Brine Tube Tubing Assembly Screen Brine Valve Body 7 Bottom Seal Retainer O Ring 15 16 x 1 3 16 Guide Cap 21 Float Rod amp Stem 22 Float Seal a 7310202 Repl Brine Valve Assemby Sy N 11 12 13 14 15 16 1 EA EA mai Ea e Zi 8 ES EN eal Ea al EA E N oO oO Key nae 5 mero NCS mosar ORing z E Not illustrated 27 28 N gt N O 00 N on oO oa ime Ea m E EE To order repair parts call toll free 1 866 986 3223 Monday Friday 8 am 7 pm EST Manufactured and warranted by Ecodyne Water Systems 1890 Woodlane Drive Woodbury MN 55125 Questions Call Toll Free 1 866 986 3223 Monday Friday 8 AM 7 PM EST or visit www ecodynewatertreatment com When you call please be prepared to provide the model date code and serial number found on the rating decal typically located on the rim below the salt lid hinges Valve Exploded View wear strip seal Bw cross section Valve Parts List Key Dus 7224087 Screw 8 32 x 1 2 req 101 7286039 Motor incl 2 ea of Key No 100 102 7231393 Motor Plate 103 0900857 Screw 6 20 x 3 8 3 req
44. ter faucet until there is a steady flow and there are no air bub bles then close this faucet 6 Close all cold water faucets and check for leaks at the plumbing connections that you made 7 Check for leaks around clips at softener s inlet and outlet If a leak occurs at a clip depressurize the plumbing turn off the water supply and open faucets before removing clip When removing clips at the softener s inlet or outlet push the single bypass valve body toward the softener See Figure 14 Improper removal may damage clips Do not reinstall damaged clips If removing clips depressurize the plumbing then push Bypass Valve body toward softener FIG 14 ADD WATER AND SALT TO THE SALT STORAGE TANK AVE Th fe Excessive Weight Hazard Use two or more people to move and lift salt bags Failure to do so can result in back or other injury 1 Using a container add about three gallons of clean water into the salt storage tank 2 Add salt to the storage tank Use nugget pellet or coarse solar salts with less than 1 impurities PLUG IN THE WATER SOFTENER During installation the water softener wiring may be moved or jostled from place Be sure all leadwire con nectors are secure on the back of the electronic board and be sure all wiring is away from the valve gear and motor area which rotates during regenerations 1 Plug the water softener into an electrical outlet that is not controlled by a
45. tion screens Figures 51 56 3 To return to the softener status screen press the t RETURN button Capacit FIG 55 p00030K recharges FIG 56 18 Customizing Features Options SET CLEAN FEATURE The Clean Feature with Sediment Guard technology is beneficial on water supplies containing ferrous clear water iron The default setting is OFF When set to ON an additional backwash and fast rinse cycle will occur first preceding the normal regenera tion sequence This provides extra cleaning of the resin bed before it is regenerated with the salt brine To conserve water set this feature OFF if your water supply does not contain iron or sediments To set this feature 1 Press the SETUP button on the softener status screen 2 Press the LEFT button twice to display the screen shown in Figure 57 Advanced setup Setup menu will change to the following screen Additional features E Advanced setup 4 Press the ADDITIONAL FEATURES button to dis play the screen shown in Figure 59 feature L7 Additi falre 5 Press the SET CLEAN FEATURE button and the display will change to show the Set clean feature screen See Figure 60 continued FIG 57 3 Press the ADVANCED SETUP button The display FIG 58 FIG 59 FIG 60 6 Press the button next to ON to enable this feature or OFF to disable it and then press the RETURN L button 7 To return to the softener
Download Pdf Manuals
Related Search