Whirlpool 3360620 Washer User Manual
Contents
1. do not have a removable front panel The cabinet and top assembly must be removed by removing clips under console on the non coin operated washer PAGE 2 DANGER You will be killed or seriously injured if you don t follow instructions amp WARNING You can be killed or seriously injured if you don t follow instructions All safety messages will identify the hazard tell you how to reduce the chance of injury and tell you what can happen if the instructions are not followed Grounded electrical outlet is required See Electrical requirements Single washer installations require 12 minimum risers to provide an air cushion and prevent noise and damage to valves Level floor Maximum slope under washer 1 inch A floor drain should be provided under the bulkhead Prefabricated bulkheads with electrical outlets water supply lines and drain facilities should be used only where local codes permit Non coin operated washers are equipped with a console push to start timer selector switches and indicator lights not pictured Coin operated washers are equipped with a meter case console timer selector switches and indicator lights The coin slide mechanism slide mounting bolt slide extension service door panel lock and key top lock and key coin vault and coin vault lock and key are not included with this washer and are needed to complete installation These items are avail2. ground path is adequate Do Not ground to a gas pipe Check with a qualified electrician if you are not sure the washer is properly grounded Do Not have a fuse in the neutral or ground circuit A 120 volf 60 Hz AC only 15 or 20 ampere fused electrical supply is required Time delay fuse or circuit breaker is recommended It is recommended thot a separate circuit serving only this appliance be provided Recommended ground method For your personal safety this appliance must be grounded This appliance is equipped with a power supply cord having 3 prong ground plug To minimize possible shock hazard the cord must be plugged into a mating 3 prong ground type outlet grounded in accordance with local codes and ordinances See Figure 1 If a mating outlet is not available it is the personal responsibility and obligation of the customer to have a properly grounded 3 prong outlet installed by a qualified electrician Warning Improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded Do not modify the plug provided with the appliance if it will not fit the outlet have a proper outlet installed by a qualified electrician 3 prong ground type outlet 3 prong ground plug ground prong power supply cord Figure 1 Now start With wash
3. able from usual industry sources Hot and cold water faucets must be within 4 feet of the back of the washer and provide water pressure 10 100 PSI A pressure reduction valve should be used in the supply line where inlet pressure entering the building exceeds 100 PSI to prevent damage to the washer mixing valve Water heater Set to deliver 140 F to 160 F water to the washer Standpipe drain system Needs a two inch minimum carry away capacity of 17 gallons per minute Top of standpipe must be at least 34 inches high and no higher than 72 inches from bottom of washer Support Floor must be sturdy enough to support loaded washer weight of 315 pounds Important Observe all governing codes and ordinances Tools needed for installation flat blade screwdriver utility knife T20 torx driver Parts supplied for installation Remove parts from packages Check that all parts were included 1 hose clamp 2 inlet hoses 4 flat water hose washers 2 front leveling legs with nuts 1 drain hose PAGE 3 Electrical requirements A4 WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet Do not remove ground prong Do not use an adapter Do not use an extension cord Failure to follow these instructions can result in death fire or electrical shock If codes permit and a separate ground wire is used it is recommended that a qualified electrician determine that the
4. ecurity is needed top and cabinet can be locked to washer back panel by using a screw type lock and key in space provided in top panel under console The screw type lock and key are available from usual industry sources PAGE 6 Typical full load sizes Load Type Loading Suggestion Load Type Loading Suggestion Heavy work clothes 3 double sheets 4 pillowcases 8 T shirts 3 pair pants 3 shirts 1 coverall 6 pair shorts 2 shirts 2 blouses 8 handkerchiefs 2 double or 1 king size sheet I tablecloth dress I blouse 2 slacks 3 shirts 2 pillowcases Check list for washer operation Check the following if the washer is not operating properly 1 Power supply cord is plugged in 2 Circuit breaker is not tripped or house fuse blown 3 Timer has been advanced to start of a cycle Water faucets are turned on Permanent Press Washer lid is closed Inlet valve is frozen if not protected from the weather 8 Suds level Excess suds will slow the spin and cause poor rinsing Operate the washer through a complete cycle with no detergent Use less detergent or a controlled suds type detergent in future loads Operating Tips AWARNING NOOR Explosion Hazard Never place items in the washer that are dampened with gasoline or other flammable fluids No washer can completely remove oil Do not dry anything that has ever had any type of oil on it including co
5. en pull out on lever to start washer 24 mif the washer fails to start or does not give the proper washer cycle time the clutch assembly of the coin operated timer can be adjusted Remove the timer from the meter case Adjust the clutch assembly screw clockwise if the washer does not start after the coin slide mechanism has been fully actuated in or out Adjust the clutch assembly screw counterclockwise if the washer segment of the Normal cycle was less than 9 minutes timer clutch adjustment screw Owner options coin operated models CAUTION Disconnect power cord 1 For EXTRA SPIN and or EXTRA WASH e Remove meter case service door e Loosen 2 screws on the timer mounting bracket and lift the 2 screws a EXTRA WASH 3 minutes e Connect LBU to LBU2 e Disconnect GY from GY2 e Set timer clutch arm as shown below Extra Wash Standard Wash Leave L on timer shaft aligned with 1 on timer and move timer clutch arm to extra wash position b EXTRA SPIN 2 minutes e Connect BK to BK2 2 For WARM RINSE and WATER SAVER e Remove screws from each end of the console bottom e Pull the console bottom forward lift and tilt it back a WARM RINSE e Connect J1 to J2 b SAVE WATER e Pull out tab on water level switch If use of a larger coin vault lock and key is desired conversion bar in lower portion of coin vault area can be removed 4 If additional s
6. er in laundry area A4 WARNING Excessive Weight Hazard Use two or more people to move and install washer Failure to do so can result in back or other injury shipping tape 1 m Remove tape that covers shipping strap Pull to completely remove the shipping strap with 2 cotterpins from the inside of the washer Pull firmly to remove the end of shipping strap from the back of the washer The shipping strap plug must be completely removed from the washer for the self leveling legs to be released Save the shipping strap for use in Step 6 Power supply cord is factory installed Peel the tape down and off each side of the cabinet Use the new hoses and washers that came with your Whirlpool washer coupling washer 2 minsert a flat washer into each end of the inlet hoses Check that washers are firmly seated in couplings PAGE 4 Inlets are plastic Do Not strip or e A hose to bottom inlet valve opening first Then second hose to top inlet Tighten couplings by hand then use pliers to make an additional two thirds turn Slide washer onto cardboard or hardboard before moving across floor 44 4 Move washer close to final position Put hook end of drain hose into standpipe Estimate length of drain hose needed when washer is in final position Hose must be cut exactly to length so hook end is held tightly over edge of standpipe If drain hose is too long cut st
7. installation Instructions Part No 3360620 IMPORTANT Read and save COMMERCIAL these instructions WASHER IMPORTANT 120 volt 60 Hz Models Installer Leave Installation Instructions with the owner Owner Keep Installation Instructions for future reference lt gt Save Installation Instructions for local m electrical inspector s use Wh 4 COMMERCIAL www whirlpool com PRODUCTS Before you start Your safety and the safety of others is very important We have provided many important safety messages in this manual and on your appliance Always read and obey all safety messages This is the safety alert symbol This symbol alerts you to hazards that can kill or hurt you and others All safety messages will be preceded by the safety alert symbol and the word DANGER or WARNING These words mean Check location where washer will be installed Proper installation is your responsibility Make sure you have everything necessary for correct installation Do Not store or operate washer below 32 F some water may remain in washer see Use amp Care Guide for Winterizing information Untape and open washer lid Remove packages and hoses from washer No T20 Torx screws On coin operated washers front access to the pump area is available by removing the two No 10 Torx screws and then removing the front panel Non coin operated washers
8. oking oils Doing so can result in death explosion or fire Inlet and drain hoses are not kinked 4 pair jeans 1 overall 3 blouses 4 slacks 6 shirts 4 tops 4 dresses It is recommended that fiberglass items not be washed in coin operated washers If these items are washed in the washer run the washer through a complete cycle to rinse any residue away that might be left in the washer Moving the washer to a new location Wedge blanket between tub ring and cabinet top Remove front legs Tape rear legs in up position place blanket in this area switch e Remove the front legs from the base of the washer e Place both rear leveling legs in the upper position and tape securely e Apply tape to the side and bottom of the cabinet near the rear e Open washer lid wedge a blanket between the tub ring and the cabinet top restricting the tub movement e Handle washer carefully Do Not drop washer while using hand truck E UCA water 43 Inlets 38 1 8 drain hose 27 3 4 connector 25 1 2 PAGE 7 CORPORATION Part No 3360620 1999 Whirlpool Corporation Prepared by Whirlpool Corporation Benton Harbor Michigan 49022 Printed in U S A
9. raight end of hose Do Not cut hook shaped end of drain hose DO NOT FORCE EXCESS LENGTH OF DRAIN HOSE DOWN THE STANDPIPE THIS COULD CAUSE SIPHONING See Step 6 5 Place hose clamp over washer drain connector Push drain hose onto washer connector use pliers to open clamp and slide clamp over drain hose Check for good fit 6 m Measure and mark a point approximately 16 inches from the plug end of the shipping strap Cut this shipping strap at this point Check that hose is not twisted or kinked and is securely in place A Put hook end of drain hose into standpipe Tightly D PO ed wrap the shipping strap around the standpipe Push plug into the nearest hole in the shipping strap 7 m Before attaching water inlet hoses run water through both faucets into a bucket This will get rid of particles in water lines that might clog hoses Mark which is the hot water faucet Santer bottom hose inlet marked H to hot water faucet Attach top hose inlet marked C to cold water faucet Tighten coupling to faucet by hand then use pliers to make final two thirds turn Q asiacx two corner posts on top of each other Tilt washer backwards and insert corner posts 3 inches in from one side of washer as shown Repeat with other corner posts on other side of washer 1 O m Use legs and nuts from parts package Screw nut down to within 1 2 inch of base 11 Insert legs into co
10. rrect holes at each front corner of washer until nuts touch washer Do Not tighten nuts until Step 15 1 2 m Tilt washer backward and remove corner posts Gently lower washer to floor Move washer to its permanent location Remove cardboard or hardboard from under washer 1 3 m Tilt washer forward raising back legs 1 inch off of floor To adjust rear self leveling legs gently lower washer to floor Check levelness of the washer by placing a carpenter s level on top of the washer first side to side then front to back 1 4 If washer is not level screw the front legs up or down to adjust Make final check with level When washer is level use wrench to turn nuts on front legs up tightly against washer base If nuts are not tight against washer base the washer may vibrate 1 5 m On coin operated washers remove the service door of the meter case Lift the service door up at the back and remove Carefully insert coin slide with the coin slide extension attached into front opening and secure with the 3 16 mounting bolt from inside the meter case The coin slide may need to be partially pushed in to insert mechanism in the front opening Replace meter case top and service door Insert coin vault with lock and key PAGE 5 1 8 m CHECK ELECTRICAL REQUIREMENTS BE SURE YOU HAVE CORRECT ELECTRICAL SUPPLY AND RECOMMENDED GROUNDING METHOD 1 9 m Check that all parts are now installed See paris lis
11. t Page 3 If there is an extra part go back through steps to see which step was skipped 20 m Turn on water faucets and check for leaks Tighten couplings if there is leaking Do Not overtighten this could cause damage to faucets 2 1 m Check that you have all of your tools Check that the shipping strap with 2 cotterpins and plug was removed from the back of the washer and used to secure the drain hose If entire strap is not removed washer may vibrate and be noisy 22 m Remove power supply cord from basket and plug into grounded outlet 23 m Check the wash cycle time Both coin operated and non coin operated washers have timers with a 9 minute wash in the Normal cycle Remove the meter case top of coin operated washers to manually start the timer Remove the rear of the console to manually start the timer Remove the rear of the console to manually operate the timer of non coin operated washers Start the washer and allow it to complete the Normal cycle cycle information Rotate counter clockwise only timer front view Coin operated timers can be started by turning the clutch assembly counterclockwise until the washer starts to fill with water Rotation pull to start pall push to stop timer rear view e Non coin operated timer cycle information is ink stamped on the rear of the timer Push in on the lever attached to the timer shaft Reset lever to the Normal cycle position th
Download Pdf Manuals
Related Search