Weed Eater 545186748 Trimmer User Manual
Contents
1. WEED EATER Trademark EJE Por favor no devuelva el aparato al lugar de compra 9 Please do not return unit to retailer Veuillez ne pas retourner outil au d taillant 1 800 554 6723 www weedeater com Instruction Manual Manual de Instrucciones Manuel d Instructions WT3100 m Y gt Z e m For Occasional Use Only WARNING A Read and follow all Safety Rules and Operating Instructions before using this product Failure to do so can result in serious injury ADVERTENCIA Lea el manual de instrucciones y siga todas las advertencias e instrucciones de seguridad El no hacerlo puede resultar en le siones graves AVERTISSEMENT Lire le manuel d instructions et bien respecter tous les avertisse ments et toutes les instructions de s curit Tout d faut de le faire pourrait entrainer des blessures graves WEED EATER 1030 Stevens Creek Road Augusta GA 30907 SIVSNVHS 545186748 Rev 1 4 15 08 BRW SAFETY RULES A WARNING when using gardening ap pliances basic safety precautions should al ways be followed to reduce the risk of fire and serious injury Read and follow all instructions This power unit can be dangerous Operator is responsible for following unit and manual instructions and warnings Read entire in struction manual before using unit Be thor oughly familiar with the controls and the prop er use of the unit Restrict the use of this unit to persons who read und2. NOTE Ensure upper handle grips are in position as shown in the following illustrations throttle handle grip on left side 4 Align holes and insert curved head tube bolt through upper and lower handles 5 Re install and securely tighten upper wing nut onto bolt 6 Retighten lower wing nut securely eave handle Upper wing nut TODS DON pp g nut aH K Lower wing nut Z NOTE When performing the following step be sure the starter rope is not caught under the cable clamps The starter rope must hang freely to operate properly Cable clamps Throttle cable 7 Align one cable clamp above the tube bolts and the other below the starter rope han dle Install the cable clamps one at a time around the tube and throttle cable NOTE Ensure throttle cable is in groove of clamps and lies flat against the upper handle tube after installation see illustration above OPERATION KNOW YOUR TRIMMER READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments Save this manual for future reference Throttle Trigger Starter Rope Handle ON OFF Switch Upper Handle Lower Handle ON OFF SWITCH The ON OFF switch is used to stop engine To stop the engine move the switch to the OFF position PRIMER BULB The PRIMER BULB removes air from the car bureto
3. instructions please call 1 800 554 6723 STARTING A COLD ENGINE ora warm engine after running out of fuel 1 Move ON OFF switch to the ON position 2 Slowly press the primer bulb 6 times 3 Move choke lever to the FULL CHOKE position 4 Squeeze the throttle trigger fully and hold through all remaining steps 5 Pull starter rope handle sharply until engine sounds as if it is trying to start but do not pull rope more than 6 times 6 As soon as engine sounds as if it is trying to start move choke lever to HALF CHOKE position 7 Pull starter rope sharply until engine runs but no more than 6 pulls NOTE If the en gine doesn t start after 6 pulls at the HALF CHOKE position move the choke lever to the FULL CHOKE position and press the primer bulb 6 times Squeeze and hold the throttle trigger and pull the starter rope 2 more times Move the choke lever to the HALF CHOKE position and pull the starter rope until the engine runs but no more than 6 pulls Ifthe engine still doesn t start itis probably flooded Proceed to START ING A FLOODED ENGINE 8 Once the engine starts allow it to run 10 seconds then move the choke lever to the OFF CHOKE position Allow the unit to run for 30 more seconds at OFF CHOKE be fore releasing the throttle trigger NOTE If engine dies with the choke le ver inthe OFF CHOKE position move the choke lever to the HALF CHOKE position and pull the rope until engine runs but no m
4. Phase 1 or Phase 2 and or CALIFORNIA DISP SERIAL EMISSION REFER TO OWNER S MANUAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS This engine is certified to be emissions compliant for the following use X Moderate 50 hours O Intermediate 125 hours L Extended 300 hours 11
5. may be liable for damages to other engine components caused by the failure of a warranted part still under warranty WHAT IS NOT COVERED All failures caused by abuse neglect or improper maintenance are not covered ADD ON OR MODIFIED PARTS The use of add on or modified parts can be grounds for disallowing a warranty 10 claim WEED EATER is not liable to cover fail ures of warranted parts caused by the use of add on or modified parts HOW TO FILE A CLAIM If you have any questions regarding your warranty rights and responsibilities you should contact your nearest authorized ser vice center or call WEED EATER at 1 800 554 6723 WHERE TO GET WAR RANTY SERVICE Warranty services or re pairs shall be provided at all WEED EATER service centers Call 1 800 554 6723 MAINTENANCE REPLACEMENT AND REPAIR OF EMISSION RELATED PARTS Any WEED EATER approved replacement part used in the performance of any warranty maintenance or repair on emission related parts will be provided without charge to the owner if the part is under warranty EMIS SION CONTROL WARRANTY PARTS LIST Carburetor Ignition System Spark Plug covered up to maintenance schedule Ignition Module Muffler including catalyst MAINTENANCE STATEMENT The owneris responsible for the performance of all re quired maintenance as defined in the instruc tion manual The information on the product label indicates which standard your engine is certified Example Year EPA
6. SEQUENTIAL OR OTHER DAMAGES WILL BE ALLOWED AND THERE ARE NO OTHER EXPRESS WARRANTIES EXCEPT THOSE EX PRESSLY STIPULATED HEREIN SOME STATES DO NOT ALLOW LIMITA TIONS ON HOW LONG AN IMPLIED WAR RANTY LASTS OR THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSE QUENTIAL DAMAGES SO THE ABOVE LIM ITATIONS OR EXCLUSION MAY NOT APPLY TO YOU This is a limited warranty within the meaning of that term as defined in the Magnuson Moss Act of 1975 The policy of WEED EATER is to continuous ly improve its products Therefore WEED EATER reserves the right to change modify or discontinue models designs specifica tions and accessories of all products at any time without notice or obligation to any pur chaser U S EPA ENVIRONMENT CANADA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OB LIGATIONS The U S Environmental Protection Agency California Air Resources Board Environment Canada and WEED EATER are pleased to explain the emissions control system warranty on your year 2007 and later small off road engine In California all small off road engines must be designed built and equipped to meet the State s strin gent anti smog standards WEED EATER must warrant the emission control system on your small off road engine for the periods of time listed below provided there has been no abuse neglect or improper maintenance of your small off road engine Your emission control system includes parts such
7. and pour 1 teaspoon of 40 1 2 cycle engine oil air cooled through the spark plug opening Slowly pull the starter rope 8 to 10 times to distribute oil Replace spark plug with new one of recom mended type and heat range Clean air filter Check entire unit for loose screws nuts and bolts Replace any damaged broken or worn parts At the beginning of the next season use only fresh fuel having the proper gasoline to oil ratio OTHER Do not store gasoline from one season to another e Replace your gasoline can if it starts to rust TROUBLESHOOTING TABLE A WARNING Always stop unit and disconnect spark plug before performing all of the recommended remedies below except remedies that require operation of the unit Spark plug incorrect Carburetor requires adjustment 4 Carbon build up on muffler outlet screen N TROUBLE CAUSE REMEDY Engine will not 1 Engine flooded 1 See Starting a Flooded Engine in start Operation Section 2 Fuel tank empty 2 Fill tank with correct fuel mixture 3 Spark plug not firing 3 Install new spark plug 4 Fuel not reaching 4 Check for dirty fuel filter replace carburetor Check for kinked or split fuel line repair or replace 5 Carburetor requires 5 Contact an authorized service dealer adjustment Engine will 1 Carburetor requires 1 See Carburetor Adjustment in not idle adjustment Service and Adjustments Section prope
8. as the carburetor and the ignition system Where a warrantable condition exists WEED EATER will repair your small off road engine at no cost to you Expenses covered under warran ty include diagnosis parts and labor MANUFACTURER S WARRANTY COV ERAGE If any emissions related part on your engine as listed under Emissions Control Warranty Parts List is defective or a defect in the materials or workmanship of the engine causes the failure of such an emission related part the part will be repaired or replaced by WEED EATER OWNER S WARRANTY RESPONSIBILITIES As the small off road engine owner you are responsible for the per formance of the required maintenance listed in your instruction manual WEED EATER recommends that you retain all receipts cov ering maintenance on your small off road en gine but WEED EATER cannot deny warran ty solely for the lack of receipts or for your failure to ensure the performance of all sched uled maintenance As the small off road en gine owner you should be aware that WEED EATER may deny you warranty coverage if your small off road engine or a part of it has failed due to abuse neglect improper mainte nance unapproved modifications or the use of parts not made or approved by the original equipment manufacturer You are responsi ble for presenting your small off road engine to an WEED EATER authorized repair center as soon as aproblem exists Warranty repairs should be completed in a rea
9. away from the operator Use only in daylight or in good artificial light Use only for jobs explained in this manual TRANSPORTING AND STORAGE Stop the unit when not in use Carry or transport the unit with engine stopped Allow the engine to cool secure unit before storing or transporting in vehicle Empty the fuel tank before storing or trans porting the unit Use up fuel left in the car buretor by starting the engine and letting it run until it stops Store unit and fuel in an area where fuel va pors cannot reach sparks or open flames from water heaters electric motors or switches furnaces etc Store the unit out of the reach of children A WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer birth de fects or other reproductive harm SPECIAL NOTICE This unit is not equipped with a temperature limiting muffler and spark arresting screen which meets the require ments of California Codes 4442 and 4443 All U S forest land and the states of California Ida ho Maine Minnesota New Jersey Oregon and Washington require by law that many inter nal combustion engines to be equipped with a spark arrestor screen If you operate in a locale where such regulations exist you are legally re sponsible for installing and maintaining the oper ating condition of these parts Failure to do so is a violation of the law If a spark arrestor is re quired in your a
10. erstand and follow unit and manual instructions and warnings Never allow children to operate this unit INSTRUCTION MANUAL A DANGER Never use blades wire or flailing devices Unit is designed for line trim mer use only Use of any other accessories or attachments will increase the risk of injury BUO SAFETY INFORMATION ON THE UNIT A WARNING Trimmer line throws ob jects violently You and others can be blinded injured Wear safety glasses and leg protec tion Keep body parts clear of rotating line Safety Glasses or similar eye protection Keep children bystanders and animals 50 feet 15 meters away If approached stop unit im mediately If situations occur which are not cov ered in this manual use care and good judge ment If you need assistance contact your authorized service dealer or call 1 800 554 6723 OPERATOR SAFETY e Dress properly Always wear safety glasses or similar eye protection when operating or performing maintenance on your unit safety glasses are available Eye protection should be marked Z87 Always wear face or dust mask if operation is dusty Always wear heavy long pants long sleeves boots and gloves Wearing safety leg guards is recommended Always wear foot protection Do not go bare foot or wear sandals Stay clear of spinning line Secure hair above shoulder length Secure or remove loose clothing or clothing with loosely hanging ties straps tassels etc T
11. guards in place Position unit so that any sharp object cannot acci dentally cause injury Store unit and fuel well out of the_reach of children SEASONAL STORAGE Prepare unit for storage at end of season or if it will not be used for 30 days or more If your unit is to be stored for a period of time e Clean the entire unit before lengthy storage e Store in a clean dry area e Lightly oil external metal surfaces FUEL SYSTEM Under FUELING ENGINE in the OPERA TION section ofthis manual see message la beled IMPORTANT regarding the use of ga sohol in your engine Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage Add stabilizer to the gasoline in the fuel tank or fuel storage container Fol low the mix instructions found on stabilizer container Run engine at least 5 minutes after adding stabilizer WARNING Recheck the idle speed after each adjustment The trimmer head must not move or spin at idle speed to avoid serious injury to the operator or others Air Filter Cover Idle Speed Screw If you require further assistance or are unsure about performing this procedure contact an authorized service dealer or call 1 800 554 6723 HELPFUL TIP During storage of your gas oil mixture the oil will sepa rate from the gas We recommend that you shake the gas can weekly to insure proper blending of the gas and oil ENGINE Remove spark plug
12. hen the engine is run at less than full throttle At lower speeds there is less engine noise and vibration Always release the throttle trigger and allow the engine to return to idle speed when not cutting To stop engine e Release the throttle trigger e Move the ON OFF switch to the OFF posi tion MAINTENANCE WARNING Disconnect the spark plug before performing maintenance except for carburetor adjustments HELPFUL TIP IMPORTANT Have all repairs other than the rec ommended maintenance described in the instruction manual performed by an authorized service dealer If any dealer other than an authorized service dealer performs work on the product WEED EATER may not pay for repairs under warranty It is your re sponsibility to maintain and perform general maintenance CHECK FOR LOOSE FASTENERS AND PARTS e Spark Plug Boot e Air Filter e Housing Screws e Debris Shield CHECK FOR DAMAGED OR WORN PARTS Contact an authorized service dealer for re placement of damaged or worn parts ON OFF Switch Ensure ON OFF switch functions properly by moving the switch to the OFF position Make sure engine stops then restart engine and continue e Fuel Tank Discontinue use of unit if fuel tank shows signs of damage or leaks e Debris Shield Discontinue use of unit if debris shield is damaged INSPECT AND CLEAN UNIT AND LABELS e After each use inspect complete unit for loose or damaged parts Clean
13. hey can be caught in moving parts Being fully covered also helps protect you from debris and pieces of toxic plants thrown by spinning line Stay Alert Do not operate this unit when you are tired ill upset or under the influence of al cohol drugs or medication Watch what you are doing use common sense Wear hearing protection Never start or run inside a closed room or building Breathing exhaust fumes can kill Keep handles free of oil and fuel UNIT MAINTENANCE SAFETY A DANGER Never start the engine with the clutch shroud removed The clutch will fly apart and cause serious injury Turn engine off and disconnect spark plug be fore performing maintenance except carbure tor adjustments Inspect unit before use Look for and replace damaged or loose parts before each use Make sure all handles guards and fasteners are in place and securely fastened Look for and repair fuel leaks before use Keep in good working condition Replace trimmer head that is chipped cracked broken or damaged in any other way before using the unit Maintain unit according to recommended pro cedures Keep cutting line at proper length Use only 0 115 diameter 8 mm WEED EATER brand cut length line see RE PLACING THE LINE Never use wire rope string etc Make sure unit is assembled correctly as shown in this manual Make carburetor adjustments with lower end supported to prevent line from contact ing any object Keep
14. instructions printed on con tainer Once oil is added to gasoline shake container momentarily to assure that the fuel is thoroughly mixed Always read and follow the safety rules relating to fuel before fueling your unit IMPORTANT Experience indicates that alcohol blended fuels called gasohol or using ethanol or methanol can attract moisture which leads to separation and formation of acids during stor age Acidic gas can damage the fuel system of an engine while in storage To avoid engine problems empty the fuel system before stor age for 30 days or longer Drain the gas tank start the engine and let it run until the fuel lines and carburetor are empty Use fresh fuel next season Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur See the STORAGE sec tion for additional information ON HELPFUL TIP If your engine switch reads push to stop it is always OFF in the ON position HOW TO STOP YOUR UNIT e To stop the engine move the ON OFF switch to the OFF position until the unit has fully stopped e If engine does not stop move choke to the FULL CHOKE position Choke Lever i G Primer Bulb Nier HOW TO START YOUR UNIT WARNING The trimmer head will turn while starting the engine Avoid any con tact with the muffler A hot muffler can cause serious burns ON OFF Switch HELPFUL TIP If your engine still does not start after following these
15. ore than 6 pulls STARTING A WARM ENGINE 1 Move ON OFF switch to the ON position 2 Move the choke lever to the HALF CHOKE position 5 3 Squeeze and hold the throttle trigger Keep throttle trigger fully squeezed until the engine runs smoothly 4 Pull starter rope sharply until engine runs but no more than 5 pulls 5 Allow engine to run 15 seconds then move the choke lever to OFF CHOKE NOTE If engine has not started pull starter rope 5 more pulls If engine still does not run it is probably flooded STARTING A FLOODED ENGINE Flooded engines can be started by placing the choke lever in the OFF CHOKE position then pull the rope to clear the engine of ex cess fuel This could require pulling the starter handle many times depending on how badly the unit is flooded If the unit still doesn t start refer to TROUBLESHOOTING TABLE or call 1 800 554 6723 OPERATING INSTRUCTIONS ALWAYS USE Eye Protection Heavy Long Pants Heavy Shoes Cut from your right to your left NOTE Keep left and right hands on grips during operation of unit as shown above to avoid covering air intake holes located on un derside of upper handle WARNING Always wear eye protec tion Never lean over the trimmer head Rocks or debris can ricochet or be thrown into eyes and face and cause blindness or other serious injury Do not run the engine at a higher speed than necessary The cutting line will cut efficiently w
16. others away when making carburetor adjustments Use only recommended WEED EATER accessories and replacement parts Have all maintenance and service not ex plained in this manual performed by an autho rized service dealer FUEL SAFETY Mix and pour fuel outdoors Keep away from sparks or flames Use a container approved for fuel Do not smoke or allow smoking near fuel or the unit Avoid spilling fuel or oil Wipe up all fuel spills Move at least 10 feet 3 meters away from fueling site before starting engine e Stop engine and allow to cool before remov ing fuel cap e Always store gasoline in a container ap proved for flammable liquids CUTTING SAFETY A WARNING Inspect the area before each use Remove objects rocks broken glass nails wire etc which can be thrown by or become entangled in line Hard objects can damage trimmer head and be thrown causing serious injury e Use unit properly Use only for trimming mowing and sweeping Do not use for edg ing pruning or hedge trimming Do not force unit It will do the job better and with less risk ofinjury at the rate for which it was designed Keep firm footing and balance Do not over reach Keep all parts of your body away from spin ning line and muffler Keep engine and cutting head below waist level A hot muffler can cause serious burns Cut only from your right to your left Cutting with the line on right side of the shield will throw debris
17. ove and discard worn line before installing new line 2 Use only 0 115 3 mm diameter WEED EATER brand cut length line 3 Insert one end of the line through the posi tioning tunnel 4 Continue to feed line through tunnel until line is centered leaving equal amounts on each side See illustration below Positioning 5 Insert ends of line one at atime through the line exit tunnels Air Filter Filter SS Air Filter Cover Screws NOTE Do not clean filter in gasoline or oth er flammable solvent to avoid creating a fire hazard or producing harmful evaporative emissions 3 Wash the filter in soap and water 4 Allow filter to dry 5 Add 10 15 drops of oil to the filter squeeze the filter to distribute oil NOTE FILTER MUST BE OILED 6 Replace parts REPLACE SPARK PLUG Replace the spark plug each year to ensure the engine starts easier and runs better Set spark plug gap at 0 025 inch Ignition timing is fixed and nonadjustable 1 Twist then pull off spark plug boot 2 Remove spark plug from cylinder and dis card 3 Replace with Champion RCJ 6Y spark plug and tighten securely with a 3 4 inch socket wrench 4 Reinstall the spark plug boot SERVICE AND ADJUSTMENTS 6 Pull the line and make sure the line is ex tended fully through the tunnels Line exit tunnels 7 Correctly installed line will be the same length on both ends CARBURETOR ADJUSTMENTS WARNING Kee
18. p others away when making idle speed adjustments The trimmer head will be spinning during most of this pro cedure Wear your protective equipment and observe all safety precautions After making adjustments the trimmer head must not move spin at idle speed The carburetor has been carefully set at the factory Adjustments may be necessary if you notice any of the following conditions e Engine will not idle when the throttle is re leased The trimmer head moves spins at idle 7 Make adjustments with the unit supported so the cutting attachment is off the ground and will not make contact with any object Hold the unit by hand while running and making ad justments Keep all parts of your body away from the cutting attachment and muffler Idle Speed Adjustment Allow engine to idle Adjust speed until engine runs without trimmer head moving or spinning idle too fast or stalling idle speed too slow e Turn idle speed screw clockwise to in crease engine speed if engine stalls or dies e Turn idle speed screw counterclockwise to decrease engine speed if trimmer head moves or spins at idle STORAGE WARNING Perform the following steps after each use Allow engine to cool and secure the unit before storing or transporting Store unit and fuel in a well ventilated area where fuel vapors cannot reach sparks or open flames from water heaters electric motors or switches furnaces etc Store unit with all
19. r and fuel lines and fills them with fuel This allows you to start the engine with fewer pulls on the starter rope Activate the primer Choke Lever bulb by pressing it and allowing it to return to its original form CHOKE The CHOKE helps to supply fuel to the engine to aid in cold starting Activate the choke by moving the choke lever to the FULL CHOKE position After the engine attempts to start move the choke lever to the HALF CHOKE position Once engine has started move the choke lever to the OFF CHOKE position 4 BEFORE STARTING ENGINE AA WARNING Be sure to read the fuel information in the safety rules before you be gin If you do not understand the safety rules do not attempt to fuel your unit Call 1 800 554 6723 FUELING ENGINE AA WARNING Remove fuel cap slowly when refueling HELPFUL TIP To obtain the correct oil mix ratio pour 3 2 ounces of 2 cycle synthetic oil into one gallon of fresh gas This engine is certified to operate on un leaded gasoline Before operation gasoline must be mixed with a good quality synthetic 2 cycle air cooled engine oil designed to be mixed at a ratio of 40 1 Poulan WEED EATER brand synthetic oil is recommended Mix gas oline and oil at a ratio of 40 1 A 40 1 ratio is obtained by mixing 3 2 ounces 95 ml of oil with 1 gallon 4 liters of unleaded gasoline DO NOT USE automotive oil or boat oil These oils will cause engine damage When mixing fuel follow
20. rea contact your authorized ser vice dealer for the proper kit SAFETY NOTICE Exposure to vibrations through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the fingers hands and joints of people prone to circulation disorders or abnor mal swellings Prolonged use in cold weather has been linked to blood vessel damage in otherwise healthy people If symptoms occur such as numbness pain loss of strength change in skin color or texture or loss of feeling in the fingers hands or joints discontinue the use of this tool and seek medical attention An anti vibration system does not guarantee the avoidance of these problems Users who oper ate power tools on a continual and regular basis must monitor closely their physical condition and the condition of this tool ASSEMBLY WARNING If received assembled repeat all steps to ensure your unit is properly assembled and all fasteners are secure Examine parts for damage Do not use dam aged parts NOTE If you need assistance or find parts missing or damaged call 1 800 554 6723 It is normal for the fuel filter to rattle in the empty fuel tank Finding fuel or oil residue on muffler is normal due to carburetor adjustments and testing done by the manufacturer ATTACH THE HANDLE 1 Remove upper wing nut and curved head tube bolt from upper handle 2 Loosen lower wing nut on lower handle 3 Insert upper handle over lower handle
21. rly 2 Crankshaft seals worn 2 Contact an authorized service dealer 3 Compression low 3 Contact an authorized service dealer Engine will not 1 Air filter dirty 1 Clean or replace air filter accelerate 2 Spark plug fouled 2 Clean or replace plug lacks power and regap or dies under 3 Carburetor requires 3 Contact an authorized service dealer a load adjustment 4 Carbon build up on 4 Contact an authorized service dealer muffler outlet screen 5 Compression low 5 Contact an authorized service dealer Engine 1 Choke partially on 1 Adjust choke smokes 2 Fuel mixture incorrect 2 Empty fuel tank and refill with excessively correct fuel mixture 3 Air filter dirty 3 Clean or replace air filter 4 Carburetor requires 4 Contact an authorized service dealer adjustment Engine runs 1 Fuel mixture incorrect 1 See Fueling Engine in Operation hot section 2 Replace with correct spark plug 3 Contact an authorized service dealer 4 Contact an authorized service dealer LIMITED WARRANTY WEED EATER a division of Husqvarna Out door Products Inc warrants to the original con sumer purchaser that each new WEED EATER brand gasoline tool or attachment is free from defects in material and workmanship and agrees to repair or replace under this warranty any defective gasoline product or attachment as follows from the original date of purchase 2 YEARS Parts and Labor when used for household pu
22. rposes 90 DAYS Parts and Labor when used for commercial professional or income producing purposes 30 DAYS Parts and Labor if used for rental purposes This warranty is not transferable and does not cover damage or liability caused by improper handling improper maintenance or alteration or the use of accessories and or attachments not specifically recommended by WEED EATER for this tool This warranty does not cover tune up spark plugs filters starter ropes cutting line or rotating head parts that will wear and re quire replacement with reasonable use during the warranty period This warranty does not cover pre delivery setup or normal adjustments explained in the instruction manual This war ranty does not cover transportation costs In the event you have a claim under this warran ty you must return the product to an authorized service dealer Should you have any unanswered questions concerning this warranty please contact WEED EATER a division of Husqvarna Outdoor Products Inc 1030 Stevens Creek Road Augusta GA 30907 1 800 554 6723 9 In Canada contact WEED EATER 5855 Terry Fox Way Mississauga Ontario L5V3E4 Giving the model number serial number and date of purchase of your product and the name and address of the authorized dealer from whom it was purchased THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY HAVE OTH ER RIGHTS WHICH VARY FROM STATE TO STATE NO CLAIMS FOR CON
23. sonable amount of time notto exceed 30 days If you have any questions regarding your warranty rights and responsibilities you should contact your nearest authorized service center or call WEED EATER at 1 800 554 6723 WAR RANTY COMMENCEMENT DATE The warranty period begins on the date the small off road engine is purchased LENGTH OF COVERAGE This warranty shall be for a pe riod of two years from the initial date of pur chase WHAT IS COVERED REPAIR OR REPLACEMENT OF PARTS Repair or re placement of any warranted part will be per formed at no charge to the owner at an ap proved WEED EATER servicing center If you have any questions regarding your warranty rights and responsibilities you should contact your nearest authorized service center or call WEED EATER at 1 800 554 6723 WAR RANTY PERIOD Any warranted part which is not scheduled for replacement as required maintenance or which is scheduled only for regular inspection to the effect of repair or re place as necessary shall be warranted for 2 years Any warranted part which is scheduled for replacement as required maintenance shall be warranted for the period of time up to the first scheduled replacement point for that part DIAGNOSIS The owner shall not be charged for diagnostic labor which leads to the determination that a warranted part is de fective if the diagnostic work is performed at an approved WEED EATER servicing center CONSEQUENTIAL DAMAGES WEED EATER
24. the unit and labels using a damp cloth with a mild deter ent Wipe off unit with a clean dry cloth CLEAN THE AIR INTAKE SCREEN The air intake screen allows air to circulate to keep the engine functioning properly and pre vents debris from entering the engine Air intake screen gt S 3 AS A WARNING Stop your unit before at tempting to clean the intake screen DO NOT USE GARDEN HOSE OR PRESSURE WASHER TO CLEAN THIS UNIT e Clean the intake screen periodically with a nylon brush CLEAN THE AIR FILTER A dirty air filter decreases engine perfor mance and increases fuel consumption and harmful emissions Always clean with engine stopped Clean filter after every 5 hours of op eration 1 Clean the air filter cover and the area around the cover to prevent dirt from falling into the carburetor chamber when the cov er is removed 2 Remove parts as illustrated It is not nec essary to remove the air filter hose from the air filter cover NOTE If the air filter hose becomes unat tached from the cover or lower handle during cleaning reattach before attempting to restart the engine or operate the unit REPLACING THE LINE For unit to operate properly the cutting line should be replaced when line becomes worn to less than 3 inches in length from the edge of the line exit tunnels on each side of the cutting head AA WARNING Only replace cutting line with engine switch in the OFF position 1 Rem
Download Pdf Manuals
Related Search