Weber 42390 Gas Grill User Manual
Contents
1. contact the Customer service representative in your region using the contact information sheet provided with your manual If Weber confirms the defect and approves the claim Weber will elect to replace such parts without charge If you are required to return defective parts transportation charges must be prepaid Weber will return parts to the purchaser freight or postage prepaid This Limited Warranty does not cover any failures or operating difficulties due to accident abuse misuse alteration misapplication vandalism improper installation or improper maintenance or service or failure to perform normal and routine maintenance including but not limited to damage caused by insects within the burner tubes as set out in this owner s manual Deterioration or damage due to severe weather conditions such as hail hurricanes earthquakes or tornadoes discoloration due to exposure to chemicals either directly or in the atmosphere is not covered by this Limited Warranty There are no other express warrants except as set forth herein and any applicable implied warranties of merchantability and fitness are limited in duration to the period of coverage of this express written Limited Warranty Some regions do not allow limitation on how long an implied warranty lasts so this limitation may not apply to you Weber is not liable for any special indirect or consequential damages Some regions do not allow the exclusion or limitation of inc2. spare LP cylinder under or near the Weber gas barbecue A WARNING Keep the ventilation openings of the cylinder enclosure free and clear of debris A WARNING Turn off the gas at the LP gas supply cylinder when the outdoor cooking gas appliance is not in use A WARNING Never store an outdoor cooking gas appliance indoors unless the LP cylinder is disconnected and removed from the outdoor cooking gas appliance A WARNING LP Cylinders must be stored outdoors out of the reach of children and must not be stored ina building garage or any other enclosed area A WARNING The LP pressure regulator and hose assembly supplied with the Weber Tank Enclosure Kit must be used Replacement LP pressure regulators and hoses must be obtained from Weber Stephen Product Co WARRANTY Weber Stephen Products Co Weber hereby warrants to the ORIGINAL PURCHASER of this Weber gas grill that it will be free of defects in material and workmanship from the date of purchase as follows All Parts 5 years when assembled and operated in accordance with the printed instructions accompanying it Weber may require reasonable proof of your date of purchase THEREFORE YOU SHOULD RETAIN YOUR SALES SLIP OR INVOICE This Limited Warranty shall be limited to the repair or replacement of parts that prove defective under normal use and service and which on examination shall indicate to Weber s satisfaction they are defective Before returning any parts
3. OFF To perform leak checks open cylinder valve by turning the cylinder valve hand wheel counterclockwise A WARNING Do not ignite burners when leak checking Check for leaks by wetting the connections with the soap and water solution and watching for bubbles If bubbles form or if a bubble grows there is a leak Check 1 Gas Line to T Connection 2 Regulator to Cylinder connection A WARNING If there is a leak at connection 1 retighten the fitting with a wrench and recheck for leaks with soap and water solution If a leak persists after re tightening the fitting turn OFF the gas DO NOT OPERATE THE GRILL Contact Customer Service 1 800 446 1071 Check 3 T Connection to Hose connections 4 The hose to Regulator connection A WARNING If there is a leak at connections 2 3 or 4 turn OFF the gas DO NOT OPERATE THE GRILL Contact Customer Service 1 800 446 1071 When leak checks are complete turn gas supply OFF at the source and rinse connections with water GAS INSTRUCTIONS REFILLING THE LIQUID PROPANE CYLINDER We recommend that you refill the LP cylinder before it is completely empty Removal of the LP cylinder 1 Close cylinder valve turn clockwise 2 Unscrew regulator coupling by turning counterclockwise by hand only 3 Loosen cylinder lock wing nut and turn cylinder lock up out of the way 4 Lift cylinder off To refill take LP cylinder to a Gas P
4. cylinder be filled at an authorized liquid propane gas dealer by a qualified attendant who fills the tank by weight IMPROPER FILLING IS DANGEROUS The liquid propane cylinder must be installed transported and stored in an upright position and should not be dropped or handled roughly Never store or transport the liquid propane cylinder where temperatures can reach 125 F 51 C too hot to hold by hand for example do not leave the liquid propane cylinder in a car on a hot day For full instructions on safe handling of liquid propane cylinders see Section Operating GAS INSTRUCTIONS IMPORTANT LP CYLINDER INFORMATION Failure to follow these DANGER statements exactly may result in a fire causing death or serious injury ADANGER A NEVER store a spare LP cylinder under or near this barbecue A NEVER fill the tank beyond 80 full A WARNING Only use this grill outdoors in a well ventilated area Do not use in a garage building breezeway or any other enclosed area CHECK THAT ALL BURNER VALVES ARE OFF Valves are shipped in the OFF position but you should check to be sure that they are turned OFF Check by pushing down and turning clockwise If they do not turn they are off Proceed to the next step If they do turn continue turning them clockwise until they stop then they are off Pro ceed to the next step CONNECTING THE LIQUID PROPANE CYLINDER A WARNING Make sure that the LP cylinder valve is clos
5. each use of the grill for nicks cracking abrasions or cuts If the hose is found to be damaged in any way do not use the grill Replace using only Summit authorized replacement hose Contact the Summit Built In Customer Service at 1 800 446 1071 e Inspect the burners for correct flame pattern Clean if necessary following the procedures outlined in the General Maintenance section of this manual e Check all gas fittings for leaks A DANGER Do not use an open flame to check for gas leaks Be sure there are no sparks or open flames in the area while you check for leaks Sparks or open flames will result in a fire or explosion which can cause serious bodily injury or death and damage to property A WARNING You should check for gas leaks every time you disconnect and reconnect a gas fitting Note All factory made connections have been thoroughly checked for gas leaks The burners have been flame tested As a safety precaution however you should recheck all fittings for leaks before using your Webe Gas Barbecue Shipping and handling may loosen or damage a gas fitting A WARNING Perform these leak checks even if your barbecue was dealer or store assembled You will need a soap and water solution and a rag or brush to apply it Note Since some leak test solutions including soap and water may be slightly corrosive all connections should be rinsed with water after checking for leaks Make sure side burner is
6. 0 Ib cylinder or failure to build a LP cylinder enclosure for a 20 Ib cylinder following the requirements for ventilation cylinder retention and separation of the LP cylinder from a heat source listed in the ANSI Standard for Outdoor Cooking Gas Appliances ANSI Z21 58 CSA 1 6 could be dangerous and could result in a fire or an explosion causing serious bodily injury or death and damage to property If you do not follow the DANGER statements exactly the Warranty on the Summit Built In gas grill will be voided LOCATING YOUR LP TANK ENCLOSURE KIT When determining a suitable location for your LP Tank Enclosure Kit installation give attention to concerns such as proximity to traffic paths and keeping any gas supply lines as short as possible Never locate the Summit LP Tank Enclosure Kit in a garage breezeway shed under an un protected overhang or other enclosed area Locate the LP Tank Enclosure Kit and structure so there is enough room to safely evacuate the area in case of a fire Non Combustible Surface 24 inches 60 96 cm Any Surface goeuns Auy 2E Se a O nN wo 96 09 SOUOUI pZ Any Surface LP Tank Enlosure CLEARANCE FROM COMBUSTIBLE SURFACES OR STRUCTURES A WARNING Clearance from the outside walls of the sides and back of the LP Tank Enclosure must be a minimum of 24 60 96cm inches any surface Refer to Typical Gas Supply Installation before starting installation A W
7. ARNING The structure island counter tops and adjacent work areas for the LP Tank Enclosure must be built from noncombustible materials only NOTE If you have questions on what materials are considered noncombustible contact you local building supplier or fire department 6 ASSEMBLY PARTS LIST Hose and regulator 1 Tank stand 1 Tank stand base 1 Tank Scale 1 A f 1 4 20 nut 6 Y Nylon washer 12 1 4 20 x 1 2 bolt 6 CD Cylinder glide 2 1 2 Flare Gasket 2 3 8 Flare Gasket 2 ASSEMBLY 7 MOUNTING THE LP TANK BRACKET Mount the LP tank bracket to the right hand side of the enclosure opening using non corrosive hardware Mounting holes are provided on the sides and bottom of your LP tank bracket Be sure to mount the bracket securley to the enclosure before use MOUNTING HARDWARE NOT INCLUDED SVD MOUNTING THE LP HOSE AND REGULATOR Securley mount the hose and regulator bracket to the top of the built in tank enclosure using non corrosive hardware MOUNTING HARDWARE NOT INCLUDED LP TANK ENCLOSURE GAS LINE LOCATIONS Area should be kept clear of sharp jagged or extremely abrasive surfaces to avoid possible damage to gas supply lines Exercise caution when pulling gas lines through built in structure GAS INSTRUCTIONS CONNECT GAS SUPPLY A 58 inch co
8. SUMMIT 42390 BUILT IN LP TANK ENCLOSURE KIT A Summit Built In LP Tank Enclosure Kit Model 21287 THESE ACCESSORIES MAY BE PURCHASED SEPARATELY YOU MUST READ THIS OWNERS GUIDE BEFORE OPERATING YOUR GAS GRILL A DANGER If you smell gas 1 Shut off gas to the appliance 2 Extinguish any open flames 3 Open lid 4 If odor continues keep away from the appliance and immediately call your gas supplier or your fire department Leaking gas may cause a fire or explosion which can cause serious bodily injury or death or damage to property A WARNING 1 Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance A WARNING Follow all leak check procedures carefully in this manual prior to barbecue operation Do this even if the barbecue was dealer assembled NOTICE TO INSTALLER These instructions must be left with the owner and the owner should keep them for future use THIS GAS APPLIANCE IS DESIGNED FOR OUTDOOR USE ONLY AWWARNING Do not try to light this appliance without reading the Lighting Instructions section of this manual 42390 US 10 01 05 LP US English National PROPANE GAS Association 2 ADANGERS amp AWARNINGS ADANGER Failure to follow the Dangers Warnings and Cautions co
9. e the gas should not be allowed to vent or migrate into the empty or hollow area of the island Ventilation openings should only communicate with the outside of the island structure so that the gas can dissipate outside of the island structure The ventilation opening should be located within 5 inches 127mm of the top of the enclosure and should have a total free area of 20 square inches This relates to 1 square inch of ventilation area per pound of stored fuel At least one ventilation opening a hole or group of holes for the purpose of ventilation needs to be on one side of the enclosure that communicates with the outside of the island structure at the bottom If a gas leak should occur or the LP cylinder should vent in the LP cylinder enclosure the gas should not be allowed to vent or migrate into the empty or hollow area of the island Ventilation openings should only communicate with the outside of the island structure so that the gas can dissipate outside of the island structure The ventilation opening should be located within 5 inches 127mm of the bottom of the enclosure and should have a total free area of 10 square inches This relates to 1 2 square inch of ventilation area per pound of stored fuel 3 The minimum size of the ventilation hole s should not be less than 1 4 inch The remote LP cylinder enclosure should be constructed with non combustible materials T
10. ed Close by turning valve clockwise A DANGER Do not use an open flame to check for gas leaks Be sure there are no sparks or open flames in the area while you check for leaks Sparks or flames will result in a fire or explosion which can cause serious bodily injury or death and damage to property Some of the tanks have differing top collar assembles The top collar is the metal protective ring around the valve One series of tanks mount with the valve facing front The other tanks mount with the valve facing away from the fuel scale These types of tanks are illustrated below You will need LP cylinder a soap and water solution and a rag or brush to apply it 1 Turn the LP cylinder so the opening of the valve is either to the front side or rear of the Weber gas barbecue Lift and hook the cylinder onto the fuel gauge 2 Loosen the cylinder lock wing nut Swing the cylinder lock down Tighten the wing nut To Connect the hose to the cylinder 3 Remove the plastic dust cover from the valve 4 Screw the regulator coupling onto the tank valve clockwise or to the right Hand tighten only Note This connection tightens clockwise and will not allow gas to flow unless the connection is tight The connection requires tightening by hand only A WARNING Do not use a wrench to tighten the connection Using a wrench could damage the regulator coupling and could cause a leak 5 Mix soap and water A ATTENTION T
11. et a similar tank in return Your LP cylinder is equipped with a quick closing coupling or type 1 valve and an OPD Overfilling Prevention Device Other LP cylinders may not be compatible with your barbecue connection e Air must be removed from a new LP cylinder before the initial filling Your LP dealer is equipped to do this e The LP cylinder must be installed transported and stored in an upright position LP cylinders should not be dropped or handled roughly e Never store or transport the LP cylinder where temperatures can reach 125 F 51 7 C too hot to hold by hand for example do not leave the LP cylinder in a car on a hot day Note A refill will last about 20 hours of cooking time at normal use The fuel scale will indicate the propane supply so you can refill before running out You do not have to run out before you refill e Treat empty LP cylinders with the same care as when full Even when the LP tank is empty of liquid there still may be gas pressure in the cylinder Always close the cylinder valve before disconnecting A CAUTION When transporting the LP cylinder make sure the plastic dust cover is in place over the valve This will keep dust and dirt from the threaded portion of the valve e Do not use a damaged LP cylinder Dented or rusty LP cylinders or LP cylinders with a damaged valve may be hazardous and should be replaced with a new one immediately LIQUID PROPANE LP CYLINDER S e The joi
12. g flame in the HIGH position the barbecue to cylinder connection may have burner control knobs and the cylinder valve or activated OFF Disconnect the regulator from the cylinder barbecue temperature only reaches 250 to Turn burner control knobs to HIGH Wait at 300 F in the HIGH position least 1 minute Turn burner control knobs OFF Reconnect the regulator to the cylinder Turn cylinder valve on slowly Refer to Lighting Instructions If problems cannot be corrected by using these methods please contact the Customer Service Representative in your area using the contact information on our web site Log onto www weber com WEBER STEPHEN PRODUCTS CO www weber com 2005 The following trademarks are registered in the name of Weber Stephen Products Co an Illinois corporation located at 200 East Daniels Road Palatine Illinois 60067 U S A Australia Smokey Joe Weber Kettle Silhouette Genesis Austria Kettle Silhouette Smokey Joe Weber Benelux Kettle Silhouette2 Smokey Joe Weber Compact Grill Configuration Botswana Weber Canada Smokey Joe Genesis China Kettle Silhouette Denmark Kettle Silhouette Smokey Joe Weber Finland Smokey Joe France Kettle Silhouette Smokey Joe Weber One Touch Germany Smokey Joe Weber One Touch Greece Smokey Joe Ireland Kettle Silhouette amp Smokey Joe Italy Smokey Joe Weber Japan Smokey Joe Weber Korea Smokey Joe Weber New Zealand Weber Smokey J
13. he remote LP cylinder enclosure should isolate the LP cylinder from the burner compartment so that it provides shielding from radiation be a flame barrier and provide protection from foreign material such as hot drippings There should be a minimum of 2 inches 50 8mm between the ground and the floor of the remote LP cylinder enclosure The LP cylinder valve should be readily accessible for hand operation A door on the remote LP cylinder enclosure to gain access to the LP cylinder valve is acceptable provided it is non locking and can be opened without the use of tools If your licensed contractor or licensed plumber builds an LP cylinder enclosure following the guidelines in the ANSI Standard for Outdoor Cooking Gas Appliances Z21 58 CSA 1 6 you need to order kit number 21287 which will contain the hose and regulator assembly mounting bracket for the regulator connection fittings and LP tank bracket for retaining the LP cylinder that must be used with the Summit Built In gas grill The hose and regulator in the kit 21287 is listed as part of the CSA listed Summit Built In gas grill ASSEMBLY ADANGER Use of any other hose and regulator assembly could be dangerous and may not provide adequate gas supply to the Summit Built In gas grill and could result in a fire or an explosion causing serious bodily injury or death and damage to property ADANGER Failure to use the the Summit Built In Tank Cabinet for a 2
14. his product has been safety tested and is only certified for use in a specific country Refer to country designation located on outer carton These parts may be gas carrying or gas burning components Please contact Weber Stephen Products Co Customer Service Department for genuine Weber Stephen Products Co replacement part s information A WARNING Do not attempt to make any repair to gas carrying or gas burning components without contacting Weber Stephen Products Co Customer Service Department Your actions if you fail to follow this product Warning may cause a fire or an explosion resulting in serious personal injury or death and damage to property GAS INSTRUCTIONS 6 Turn on the cylinder valve 7 Check for leaks by wetting the fitting with the soap and water solution and watching for bubbles If bubbles form or if a bubble grows there is a leak If there is a leak turn off the gas and tighten the fitting Turn the gas back on and recheck with the soap and water solution If leak does not stop Contact the Customer Service Representative in your region using the contact information sheet provided with your manual Do not use the barbecue 8 When leak checking is complete turn gas supply OFF at the source and rinse connections with water CHECK FOR GAS LEAKS After a period of nonuse we recommend that you perform the following maintenance procedures for your safety A WARNING Check the hose before
15. idental or consequential damages so this limitation or exclusion may not apply to you Weber does not authorize any person or company to assume for it any other obligation or liability in connection with the sale installation use removal return or replacement of its equipment and no such representations are binding on Weber This Warranty applies only to products sold at retail WEBER STEPHEN PRODUCTS CO Customer Service Center 1890 Roselle Road Suite 308 Schaumburg IL 60195 USA www weber com ASSEMBLY TYPICAL 20 LP PROPANE GAS SUPPLY INSTALLATION We strongly recommend that you use the Summit Built In Tank Cabinet 21280 for installations using a 20 Ib LP cylinder mounted remotely in an island structure The Summit Built In Tank Cabinet is a CSA listed accessory for installing a remote mounted 20 Ib LP cylinder in an island structure Summit Built In Tank Cabinet has a hose and regulator assembly and gas connections for connecting a remote mounted LP cylinder to the Summit Built In gas grill The hose and regulator is listed as a required part of the CSA listed Summit Built In gas grill The Summit Built In Tank Cabinet also meets the requirements for venting tank retention and separation of the LP cylinder from a heat source as outlined in the ANSI Standard for Outdoor Cooking Gas Appliances Z21 58 CSA 1 6 for LP enclosures The Summit Built In Tank Cabinet has its own installat
16. ion guide If you do not use the Summit Built In Tank Cabinet you need to hire a licensed contractor or licensed plumber and they need to follow the requirements described in the ANSI Standard for Outdoor Cooking Gas Appliances Z21 58 CSA 1 6 for LP enclosures The requirements described in the Standard for Outdoor Cooking Gas Appliances Z21 58 CSA 1 6 are as follows A remote enclosure for an LP gas cylinder shall be ventilated by openings at both the upper and lower levels of the cylinder This shall be accomplished by one of the following a One side of the remote LP cylinder enclosure shall be completely open or b If the remote LP cylinder enclosure is designed to have four sides a top and a bottom ventilation is required for the remote LP cylinder enclosure 1 There should be at least two ventilation openings a hole or group of holes for the purpose of ventilation in the sidewalls of the island structure The openings should be located within 5 inches 127mm of the top of the enclosure The ventilation openings should be equally sized and spaced at a minimum of 90 degrees and be unobstructed The openings shall have a total free open area of not less than 20 square inches This relates to1 square inch of ventilation area per pound of stored fuel capacity 2 Ventilation openings a hole or group of holes for the purpose of ventilation should be provided at floor level The ventilation openings should have a to
17. l parts are in place The unit must be properly assembled according to the instructions outlined in the Assembly Instruction section of the Owner s Guide LIQUID PROPANE GAS UNITS ONLY A Use the regulator that is supplied with your Weber Tank Enclosure Kit A Do not attempt to disconnect the gas regulator or any gas fitting while your barbecue is in operation AA dented or rusty liquid propane cylinder may be hazardous and should be checked by your liquid propane supplier Do not use a liquid propane cylinder with a damaged valve A Although your liquid propane cylinder may appear to be empty gas may still be present and the cylinder should be transported and stored accordingly Alf you see smell or hear the hiss of escaping gas from the liquid propane cylinder 1 Move away from liquid propane cylinder 2 Do not attempt to correct the problem yourself 3 Call your fire department WARRANTY OPERATING A WARNING Only use the Weber Tank Enclosure Kit outdoors in a well ventilated area Do not use in a garage building breezeway or any other enclosed area A WARNING Your Weber Tank Enclosure Kit shall not be used under an unprotected combustible roof or overhang A WARNING Your Weber Tank Enclosure Kit is not intended to be installed in or on recreational vehicles and or boats A WARNING Keep any electrical supply cord and the fuel supply hose away from any heated surface A WARNING Never store an extra
18. nt where the hose connects to the LP cylinder must be leak tested each time the LP cylinder is reconnected For example test each time the LP cylinder is refilled e Be sure the regulator is mounted with the small vent hole pointed downward so that it will not collect water This vent should be free of dirt grease bugs etc e The LP cylinder and connections supplied with your Weber gas barbecue have been designed and tested to meet government American Gas Association and Underwriters Laboratories requirements RUCTIONS If you have questions about spare LP cylinders contact eustomecn Service at 1 800 446 1071 All LP tank supply systems must include a collar to protect the cylinder valve e The LP cylinder must be a 20 lb size 18 1 4 inches high 12 1 4 inches in diameter e The cylinder should be constructed and marked in accordance with the Specifications for LP Gas Cylinders of the U S Department of Transportation D O T or the National Standard of Canada CAN CSA B339 Cylinders Spheres and Tubes or Transportation of Dangerous Goods and Commission as applicable TANK ENCLOSURE TROUBLESHOOTING PROBLEM CHECK CURE Burner does not light Is gas supply off Turn supply on Flame is low in HIGH position Is fuel hose bent or kinked Straighten fuel hose Burners do not light or burners have a The excess flow safety device which is part of To reset the excess flow safety device turn all small flickerin
19. ntained in this Owner s Manual may result in serious bodily injury or death or in a fire or an explosion causing damage to property AWARNINGS ADo not store a spare or disconnected liquid propane cylinder under or near the barbecue A lmproper assembly may be dangerous Please carefully follow the assembly instructions in this manual A Do not operate the Weber gas barbecue if there is a gas leak present A Do not use a flame to check for gas leaks A Combustible materials should never be within 24 60 96cm inches of the top bottom back or sides of your Weber gas barbecue A Do not put a barbecue cover or anything flammable on or in the storage area under the barbecue A Your Weber gas barbecue should never be used by children Accessible parts of the barbecue may be very hot Keep young children away while it is in use A You should exercise reasonable care when operating your Weber gas barbecue It will be hot during cooking or cleaning and should never be left unattended or moved while in operation A Liquid propane gas is not natural gas The conversion or attempted use of natural gas in a liquid propane unit or liquid propane gas in a natural gas unit is dangerous and will void your warranty ADo not attempt to disconnect any gas fitting while your barbecue is in operation A Keep any electrical supply cord and the fuel supply hose away from any heated surfaces A Do not use this Weber tank enclosure kit unless al
20. oe Nigeria Weber Norway Smokey Joe Weber Portugal Weber South Africa Smokey Joe Weber Kettle Configuration Spain Smokey Joe Weber Sweden Kettle Silhouette Smokey Joe Switzerland Kettle Silhouette Smokey Joe Weber United Kingdom Smokey Joe Weber Weber One Touch U S A Kettle Configuration Kettle Silhouette amp Smokey Joe Weber One Touch Firespice Go Any where U S A Kettle Configuration Kettle Silhouette Genesis Flavorizer Crossover Flamgo Performer Rapidfire Tuck N Carry Jumbo Joe Bar B Kettle Master Touch Spirit Grill Out Summit Platinum 1 800 Grill Out Ranch Matchless Flame Zimbabwe Weber Kettle Configuration Kettle Silhouette Printed in USA
21. ropane dealer A WARNING We recommend that your LP cylinder be filled at an authorized LP gas dealer by a qualified attendant who fills the cylinder by weight IMPROPER FILLING IS DANGEROUS A CAUTION When transporting the LP cylinder make sure the plastic dust cover is in place over the valve This will keep dust and dirt from the threaded portion of the valve CHECKING THE FUEL LEVEL IN YOUR TANK Check the fuel level by viewing the color indicator level line on the side of the tank scale 1 Empty 2 Medium 3 Full Cycic ecie e Crciecrecieaje SAFE HANDLING TIPS FOR LIQUID PROPANE GAS CYLINDERS Liquid Propane LP gas is a petroleum product as are gasoline and natural gas LP gas is a gas at regular temperatures and pressures Under moderate pressure inside a cylinder LP gas is a liquid As the pressure is released the liquid readily vaporizes and becomes gas e LP gas has an odor similar to natural gas You should be aware of this odor e LP gas is heavier than air Leaking LP gas may collect in low areas and prevent dispersion e To fill take the LP cylinder to an RV center or look up gas propane in the phone book for other sources of LP gas A WARNING We recommend that your LP cylinder be filled at an authorized LP gas dealer by a qualified attendant who fills the tank by weight IMPROPER FILLING IS DANGEROUS A WARNING If you exchange your LP cylinder make sure you g
22. rrugated gas line is supplied with the grill This line needs to pass through the gas inlet opening to the main gas supply 1 Connect the corrugated gas line to the manifold located on the right hand side of grill under the control panel Note Leave an access in the island structure for gas supply and regulator service not inside the grill structure Weber has a gas line and regulator access door part 36311 available from your dealer or call Customer Service at 1 800 446 1071 2 Uncap one flare fitting from the 90 Connection located inside the Summit Built In Tank Cabinet 21280 top view 3 Use the 1 2 inch flared gasket to ensure proper seal NOTE Only use the 3 8 inch flared gasket if you are installing the optional side burner 4 Connect the corrugated gas line to the 90 Connection top of box Corrugated Gas Line to Manifold 905 fitting Use Bushing for Gas Line Hole 1 2 Flared Gasket back of box Cap Optional Side Burner Side View top of box Corrugated Gas Line to Manifold back of box Optional Side Burner Connection to LP Tank Side View FILL LIQUID PROPANE CYLINDER To fill take the liquid propane cylinder and filler adapter to an RV center or look up gas propane in the phone book for other sources of liquid propane gas AWARNING We recommend that your liquid propane
23. tal free area of not less than 10 square inches This relates to 1 2 square inch of ventilation area per pound of stored fuel capacity There should be at least two ventilation openings if the ventilation openings at floor level are in the sidewall The ventilation openings should be within 5 inches 127mm of the floor The ventilation openings should be of equal size and be spaced at a minimum of 90 degrees and should be unobstructed 3 The minimum size of the ventilation hole s should not be less than 1 4 inch 4 The ventilation openings in the sidewalls should not allow venting into the empty or hollow area of the island If a gas leak should occur or the LP cylinder should vent in the LP cylinder enclosure the gas should not be allowed to vent or migrate into the empty or hollow area of the island Ventilation openings in the sidewalls of the enclosure should only communicate with the outside of the island structure so that the gas can dissipate outside of the island structure If the remote LP cylinder enclosure has four sides a top anda bottom and is intended for installation in a built in island enclosure 1 Atleast one ventilation opening a hole or group of holes for the purpose of ventilation needs to be on one side of the enclosure that communicates with the outside of the island structure If a gas leak should occur or the LP cylinder should vent in the LP cylinder enclosur
Download Pdf Manuals
Related Search