Vector VEC011 Automobile Battery Charger User Manual
Contents
1. Vec011_VW011 Manual 061005 6 16 05 12 12 PM Page 8 VECO11 VWC011 TWO_YEAR LIMITED WARRANTY PROGRAM This linited warranty program is the only one that applies to this product and it sets forth all the responsibilities of Vector Manufacturing regarding this product There is no other warranty other than those ECTOR YE Freedom of POWER described herein This Vector Manufacturing product is warranted to the original purchaser only to be free of defects in materials and workmanship for two years from the date of purchase without additional charge The warranty does not extend to subsequent purchasers or users Manufacturer will not be responsible for any amount of damage in excess of the retail purchase price of the product under any circumstances Incidental Mm a t rt r and consequential damages are specifically excluded from coverage under this warranty This product is not intended for commercial use This warranty does not apply to accessories or dange to units from misuse or incorrect installation connection Misuse includes wiring or connecting to improper 12 Vo It DC Powe r S u pply polarity power sources RETURN REPAIR POLICY Defective products other than accessories may be returned to manufacturer Any Porta bi e C ord l ess Rec ha rgea bi e defective product other than accessories that is returned to manufacturer within 30 days of the date of purchase will be replaced free of charge If such a product is2. Outlet also allows for DC recharging froma vehicle or other 12 volt source AC Recharge Port The AC Recharge Port allows for 120 volt AC recharging of the unit The AC Recharge Adapter s barrel connector plugs into this port during recharge WorkLight Located on the center of the handle the worklight provides proper lighting while changing a tre or connecting the unit to a battery It is activated by the Worklight Power pushbutton located on the lower right side of the control panel Applications e Jurmmp start most engines with standard 12 volt DC battery systems such as boats small trucks cars airplanes RVs personal watercraft snowmobiles tractors etc e Use the 12 volt accessory outet to operate such appliances as 12 volt DC fans fluorescent worklights air compressors spotlights TVs portable radios cassette or CD players The unit can quick charge a cellular phone using the phone s 12 volt DC adapter cord e Illuminate areas under the hood inside tents and work areas USING THE UNIT AS A J UMP STARTER This J ump Starter is equipped with a safety Power Switch that only allows energy to flow when proper connections are made to battery and frame Once the connections are properly made turn the switch ON to jump start the vehicle 1 Turn OFF vehicle ignition and all accessories radio A C lights connected cell phone chargers etc Place vehicle in park and set the emergency brake 2 Make sure the Jump
3. Starter Power Switch is turned to OFF 3 Remove jumper clamps from clamp tabs Connect the RED clamp first then the BLACK damp NEGATIVE CABLE AND CARLA D CLAMP BLACK CLAMP RED 4 Procedure for jump staring a NEGATIVE GROUNDED SYSTEM negative battery terminal is connected to chassis MOST COMMON 4a Connect POSITIVE RED clamp to vehicle battery s POSITIVE terminal 4b Connect NEGATIVE BLACK clamp to chassis or a solid non voving metal vehicle component or body part NEVER CLAMP DIRECTLY TO NEGATIVE BATTERY TERMINALOR MOVING PART 5 Procedure for jump starting POSITIVE GROUND SYSTEMS Note In the rare event that the vehicle to be started has a POSITIVE GROUNDED SYSTEM positive battery terminal is connected to chassis replace steps 4a and 4b above with steps 5a and 5b then proceed to step 6 5a Connect NEGATIVE BLACK clamp to vehicle battery s NEGATIVE teminal 5b Connect POSITIVE RED CLAMP to vehicle chassis or a solid non moving metal vehicle component or body part NEVER CLAMP DIRECTLY TO POSITIVE BATTERY TERMINAL OR MOVING PART When clamps are connected properly turn the Junp Starter Power Switch to ON Turn ON the ignition and crank the engine in 5 6 second bursts untl engine starts Turn the Jump Starter Power Switch back to the OFF position Disconnect the N EGATIVE engine or chassis clamp first then disconnect the PO SITIVE battery clamp FOLLOW ALL SAFETY INSTR
4. in use Note Read this User s Manual and product labeling carefully before using Follow all recommended warnings cautions and safety procedures as well as manufacturer s guidelines for your vehicle battery FIRST AID Skin If battery acid comes in contact with skin rinse immediately with water then wash thoroughly with soap and water If redness pain or irritation occurs seek immediate medical attention Eyes If battery acid comes in contact with eyes flush eyes immediately for a minimum of 15 minutes seek immediate medical attention CAUTIONS Use only the supplied cords adapters for recharging this unit Do not recharge for more than 3 4 hours maximum using 12 volt DC method Recharge unit after each use All on off switches should be in the OFF position when the unit is charging or not in use Make sure all switches are in the OFF position before connection to a power source or load Never insert anything other than the supplied power recharging cords or recommended appliance power recharging cords into the 12 volt DC charging power socket on this unit Do not use any accessory that is not recommended or provided by the manufacturer Do not use this unit to operate appliances that draw more than 12 amps This system is not designed to be used as a replacement for a vehicular battery Do not attempt to operate a vehicle that does not have a battery installed Although this unit contains a non spillable battery
5. need periodic charging to replace energy lost through self discharge When the unit is not in use Vector recommends that the battery is recharged at least every 60 days Check the battery charge level by pressing the battery status button The LED charge status display will indicate the level of battery charge When only one red LED lights recharge the unit Note Recharging battery after each use will prolong battery life frequent heavy discharges between recharges and or overcharging will reduce battery life The battery can be recharged using an AC or DC adapter see below 120 VOLT AC RECHARGE 12 VOLT DC TO ADAPTER DC RECHARGE ADAPTER A CAUTION Make sure ON OFF Power Switch and Area Light are turned OFF during recharge as this may slow recharge function 120 Volt AC Recharge The AC recharge adapter is a UL listed wall type unit that operates from any 120 volt 60 Hz AC supply that has a standard North American outet The adapter has a barrel connector that plugs into the unit s recharge port Make sure the Jun p Starter Power Switch and Worklight Power Switch are turned O FF during AC recharge When an AC recharge adapter is plugged into the recharge port the battery charge level display will autormatically activate As recharging progresses the red LEDs will light one by one Charge the unit untl the green CHARGED indicator lights then disconnect the AC Recharge Adapter The AC recharge system is an automatic taper ch
6. rated up to 5 amps 1 Lift up the cover of the unit s 12 volt DC outlet 2 Insert the appliance s 12 volt DC plug into the units 12 Volt DC Accessory O utlet 3 Switch on the appliance and operate as usual 4 Periodically press the Battery Charge Level Pushbutton to check battery status A CAUTION Make sure that the J ump Starter Power Switch is ALWAYS in the OFF positon when using the unit s 12 Volt DC Accessory Outlet DO NOT OPERATE APPLIANCES THAT DRAW MORE THAN 12 AMPS A WARNING N EVER INSERT A CIGARETTE UGHTER INTO THE UNITS ACCESSORY OUTLET USING THE WORKLIGHT This unit is equipped with a convenient Worklight built into the handle It is operated by the ON OFF UG HT pushbutton on the lower right side of the front panel see the figure on page 2 for location CARE AND MAINTENANCE This product has a sealed lead acid battery that should be kept fully charged Recharge before first use immediately after each use and every 60 days if not used frequently Failure to do this may reduce the battery life dramatically Note This unit is delivered in a partially charged state you must fully charge it before using it for the first time Initial AC charge should be 40 hours Charging Recharging lead acid batteries require routine maintenance to ensure a full charge and long battery life All batteries lose energy from self discharge over tme and more rapidly when they are at higher temperatures Therefore batteries
7. returned more than 30 days but less than two E t years from the purchase date manufacturer will repair the unit or at its option replace it free of charge If the unit is repaired new or reconditioned replacement parts may be used at manufacturer s option A unit may be replaced with a new or reconditioned unit of the sare or comparable design The repaired or replaced unit will then be warranted under the terms of the remainder of the warranty period The customer is responsible for the shipping charges on all returned itens after 30 days During the warranty period manufacturer will be responsible for the return shipping charges UMIMATIONS This warranty does not cover accessories bulbs fuses and batteries defects resulting from normal wear and tear including chips scratches abrasions discoloration or fading due to usage or exposure to sunlight accidents darrage during shipping to our service facility alterations unauthorized use or repair neglect misuse abuse failure to follow instructions for care and maintenance fire flood and Acts of God If your problem is not covered by this warranty call our Technical Support Department at 954 584 4446 or toll free at 866 584 5504 for general repair information and charges if applicable You may also START IT l Amps Jump Start System INSTANT i VOU UE POWER SFP LY 1 v START IT W 3 gt Amps System ART 2 vo LT OC Power SUPPLy contact us through our website at w
8. Ge 26 ee Os ee Oe BE ee ee ews 5 Replacement Parts s s402 bse s See ea We YE SSE ew rd eee ee ee Ses 6 Worklight Bulb Replacement 0 2 e ee 6 Bbatery DiSposSal sina 488 8 y sd eee eee ok Pe ee ole GS wy ee oe 7 Troubleshootng aaa aaa et ade bos5 6 kS Sos ee SR ESSE HEARSE ees 7 SPeCCIICOUONGS 6442 s ror bt oe SASS See deh ee ee be hee Se Ss 7 INTRODUCTION Thank you for choosing the START IT J ump Starter This compact jump starter is unique in the amount of energy it can supply for its size The internal battery isa high density sealed lead acid battery that stores and delivers energy comparable to full sized ordinary jump starters Please read this guide carefully before use to ensure optimum performance and avoid damage to the unit or items that you are using it with The START IT J ump Starter is a compact durable portable jump start system for vehicles and boats that have a standard 12 volt battery system This self contained rechargeable system will start most vehicles and boats without the need for a host vehicle or 120 volt AC power supply It can also be used as a Safe portable source of 12 volt DC electric power in remote locations and or emergency situations It is ideal for use with 12 volt DC cordless portable rechargeable products and DC AC power inverters FEATURES e Keyless ON OFF safety Jump Starter Power Switch e Cordless rechargeable includes AC and DC charging adapters e Builtin non spill
9. UCTIONS FOUND ON PAGES ii AND iii OF THIS USER S MANUAL O ON O e If vehicle fails to start turn OFF the ignition turn OFF the Jump Starter Power Switch disconnect the jump start system s leads and investigate why the engine did not start e Recharge this unit fully after each use A WARNINGS e Jump Starter Power Switch should be OFF prior to jump starting 3 Vec0O11 VW011 Manual 061005 6 16 05 12 12 PM Page 4 e This power system is to be used ONLY on vehides or boats with 12 volt DC battery systems e Never touch RED and BLACK damps together this can cause dangerous sparks power arcing and or explosion e Vehicles that have on board computerized systems may be damaged if vehicle battery is jump started Before jump starting this type of vehicle read the vehicle manual to confirm that external starting assistance is advised e Excessive engine cranking can damage the vehicle s starter motor If the engine fails to start after the recommended number of attempts discontinue jump start procedure and look for other problems that need to be corrected e After use turn the J ump Starter Power Switch OFF e Replace worn or defective parts immediately contact the Customer Service Department toll free 866 584 5504 USING THE UNIT AS A 12 VOLT DC PORTABLE POWER SUPPLY This unit is a portable power source for use with all 12 volt DC accessories equipped with a male accessory outlet plug that are
10. WARRANTY INFORMATION IMPORTANT SAFETY INFORMATION SAVE THESE INSTRUCTIONS WARRANTY IS NON TRANSFERABLE AND NON REFUNDABLE TO REDUCE THE RISK OF INJURY USER MUST READ AND UNDERSTAND THIS INSTRUCTIONAL MANUAL THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING THE OPERATION AND WARRANTY OF THIS PRO DUCT PLEASE RETAIN FOR FUTURE REFEREN CE RDO61005 4140 S W 30th Ave Ft Lauderdale FL33312 U S 2005 VECTOR MAN UFACTURNG Toll Free 866 5845504 MADE IN CHINA r www vectormfg com Vec0O11 VW011 Manual 061005 6 16 05 12 12 PM Page ii IMPORTANT SAFETY INSTRUCTIONS WARNINGS 1 When working with lead acid batteries always make sure immediate assistance is available in case of accident or emergency 2 Always use protective clothing and eyewear when using this product contact with battery acid may cause blindness and or severe burns Be aware of first aid procedures in case of accidental contact with battery acid 3 There is a risk of explosive gases being released when lead acid batteries are being charged or discharged Failure to follow instructions may cause property damage explosive hazard and or personal injury 4 Make sure the power switch is OFF before connecting battery clamps to discharged battery 5 When charging unit from a 120 volt AC electrical outlet in any wet or damp area make sure that the outlet used is protected by a ground fault interrupt GFCI outiet 6 When charging the unit nea
11. able maintenance free heavy duty 9 amp hour sealed lead acid battery e Requires no maintenance other than recharging for optimum operation e Heavy duty industrial grade copper clamps and 6AWG jumper cables with exclusive recessed cable holsters e Exclusive clamp tabs that keep jumper cables out of the way until they are needed e Easy to read LED battery charge status indicators Vec0O11 VW011 Manual 061005 6 16 05 12 12 PM Page 2 BATTERY WORKUGHI CHARGE STATUS INDICATORS CHECK 12 VOLT DC ACCESSORY j sx OUTLET OS AC aah RECHARGING PORT KEYLESS ON OFF p J UMP STARTER pied PUSHBUTTON FOR POWER SWITCH BATTERY STATUS f ETETETT E E WORKLIGHT POWER PUSHBUTTON Battery Charge Status Indicators A series of three LED indicators two red and one green display the level of charge in the battery The left red LED indicates minimum battery charge Charge the batery when only a single red LED is lit The center red LED indicates moderate battery charge level W hen the green LED is lit the battery is at full charge The charge status LEDs will light when the charge status pushbutton is pressed or automatcally during AC recharge operation During DC charging the charge status pushbutton can be pressed periodically to monitor recharging progress 12 Volt DC Accessory Outlet This accessory outet is provided for use with appliances that are 12 volt DC compatible The DC Accessory
12. acement parts bulbs batteries charging adapters etc contact Vector Technical Support toll free 866 584 5504 There are no user serviceable parts inside the unit Periodically the cables and connectors should be inspected for damage corrosion dust and dirt If surfaces are dirty they can be wiped clean with a cloth moistened with water and a drop of detergent Contacts can be wiped clean with a dry cloth A WARNING Do not operate unit if there is any evidence of damage The product must be returned to manufacturer for testing and repair Replace any damaged charging adapters immediately before further use Bulb Replacement You will need a small Phillips head screwdriver and a cartridge or festoon type 12 volt 100 mA bulb 1 Make sure the Worklight is turned OFF 2 Remove the two Phillips type screws turn counterclockwise 3 Lift off the lens and set it aside 4 Move one clip to free one end of the bulb 5 Remove the bulb A CAUTION DO NOT USE ANY METAL TOOLS TO REMOVE OR REPLACE BULB 6 Snap the new bulb in place 7 Snap lens in place and replace the 2 screws 8 Turn screws clockwise to secure NOT TO OVER TIGHTEN Battery Disposal Contains a maintenance free sealed non spillable lead acid battery which must be disposed of properly Recycling is required contact your local authority for information Failure to comply with local state and federal regulations can result in fines or imprisonment For more inf
13. arge and can be left connected to the main unit for long periods See the figure on page 2 for AC Recharge Port location 12 Volt DC Recharge Recharging the J unqp Starter from an external DC power source requires the use of the DC To DC Recharge Adapter This adapter has a male DC connector at each end Unlike the AC recharge method DC recharge does NOT automatically activate the battery status display and provide a taper charge Battery status can still be monitored by pressing the battery status level pushbutton 1 Insert the gold ipped DC DC charging adapter plug into the vehicle s 12 volt DC accessory outlet 2 Insert the silvertipped end plug into the 12 volt DC accessory outlet on the front panel of the unit 3 Charge the unit unt the green CHARGED indicator lights when the battery status level pushbutton is pressed VecO11 VW011 Manual 061005 6 16 05 12 12 PM Page 6 4 When charging is completed remove the charging cord and store in a Safe place Make sure ON OFF Safety Switch and Worklight are turned OFF during 12 Volt DC Recharge as this may slow the process Note The DC recharge method will recharge the unit s battery but the green LED may not light if the charging source is below 12 6 volts AC recharge is the recommended method A WARNINGS e DO NOT EXCEED 3 HOURS MAXIMUM OF CHARGING TIME USING THE 12 VOLT DC METHOD e NEVER leave unattended while DC charging Replacement Parts For repl
14. it is recommended that it be kept upright during storage use and recharging To avoid possible darmage that may shorten the unit s working life protect it from direct sunlight direct heat and or moisture Check unit periodically for wear and tear Replace worn or defective parts immediately contact the Custorer Service Deparment at 866 584 5504 N ever submerge this unit in water or expose it to rain or snow Never attempt to jump start a frozen battery All wires cables and cords rrust be positioned so they cannot be tripped over or damaged by moving parts pinching or abrading SAVE THESE INSTRUCTIONS Vec011_VW011 Manual 061005 6 16 05 12 12 PM Page iv 4 TABLE OF CONTENTS IMTOQUCHOM 2 222628 bee bs SS SSO eta tee ewes be cee eee ee ee a 1 Peele Soar mos ee hee ee ee ee ee ee ee ee ee ee 1 Battery Charge Sus 1 4665 so2 56h 60 96s oo 5 OG 4 Sb wE a Soe Sd Kee EER 2 12 Volt DC Accessory Outet snk eee ay RRS ewe Be wwe Ee Eee MS RS 2 AC Recharge Port aaa ee eats eRe a ee wt Be a Geer Ete ee ee 2 NVGISNOME sosi aay dG ews ood pee eee eS Seb ASSES EM Cee ee oe eee 2 2 APPlicatons 2445 45 44 55 4484985554445 Dee SS oe hE SES OSE DEES 2 Using the Unit as a Junp Starter aaoo a 3 Using the Unit as a 12 Volt DC Portable Power Supply aasan oaa aa 4 Using the Worklight 6 sa534 68 655 be b based ee REE EE See eS See Se He EES 4 Care and Maintenance e 4 Charging Recharging s t6 8 52sec bee Fe
15. ormation on recycling this battery call toll free 800 822 8837 A WARNINGS Do not dispose of the battery in fire as this may result in an explosion Before disposing of the battery protect exposed terminals with heavy duty electrical tape to prevent shorting shorting can result in injury or fire Do not expose battery to fire or intense heat as it may explode TROUBLESHOOTING Unit Fails to J ump Start e Make sure unit s power switch is in the ON position e Check that Jump Starter has a full charge e Make sure a proper polarity cable connection has been established see Using the Unit as a Jump Starter page 3 12 Volt Outlet Fails to Deliver Power e Make sure a proper 12 volt adapter connection has been established e Check that Jump Starter has a full charge 12 Volt Outlet Shuts Off Disconnect unit and allow to cool for 10 minutes Note When drawing more than 12 amps from the 12 volt outlet unit will shut off Worklight Does Not Come On e Check that Jump Starter has a full charge SPECIFICATIONS Jump Start Clamps 300 amps heavy duty copper Jumper Cables 6AW G welding cable Peak Amps 600 Boost Amps 300 Battery High Density AGM 12 volt 9 Ah sealed lead acid Worklight Bulb 12 volt 100 mA festoon type DC Accessory O utet Protection 12 amps self esetting breaker
16. r water do not allow the electrical cords and outlets to get wet electrical shock could result 7 Jump start procedures should only be performed in a safe dry well ventilated area 8 Always store battery camps when not in use Never touch battery clamps together this can cause dangerous sparks power arcing and or explosion 9 When using this unit in proximity to the vehicle s battery and engine stand the unit on a flat stable surface and be sure to keep all clamps cords clothing and body parts away from moving vehicle components 10 Do not wear vinyl clothing when jump starting a vehicle friction can cause dangerous static electricity sparks Remove all jewelry or metal objects that could cause short circuits or react with battery acid 11 Always disconnect the NEGATIVE BLACK jumper cable first followed by the POSITIVE RED jumper cable 12 Never allow RED and BLACK clamps to touch each other or another common metal conductor this could cause damage to the unit and or create sparking explosion hazard Always store battery clamps when not in use 13 Do not expose battery to fire or intense heat as it may explode Before disposing of the battery protect ex posed terminals with heavy duty electrical tape to prevent shorting shorting can result in injury or fire 14 Do not smoke use matches or cigarette lighters while working on a vehicle s battery system 15 Keep unit out of reach of children whether stored or
17. ww vectornfg com STATE LAW RIGHTS This warranty gives you specific legal rights Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the exclusions or limitations stated herein may not apply This warranty gives the purchaser specific legal rights other rights which vary from state to state may apply PORTARE 1 oONDLCSS RCCHARRE nwt gt TO REQUEST WARRANTY SERVICE FOR THIS PRO DUCT Contact Technical Support by telephone fax or SYARANT PORTABLE mail see below We suggest that you keep the original packaging in case you need to ship the unit When POWER SORULESS RECHA returning a product indude your name address phone number dated sales receipt or copy and a Te description of the reason for return and product serial number After repairing or replacing the unit we will make every effort to return it to you within four weeks WARRANTY ACTIVATION Please complete Warranty Activation Card and mail to Vector Manufacturing Enter the Model Number and STARFIT Jump Starter as Product Type All Vector products must be registered within 30 days of purchase to activate this warranty Mail the completed registration form along with a copy of the original sales receipt to USER S MANUAL ATIN CUSTOMER SERVICE 4140 SW 30th Awe Ft Lauderdale FL 33312 e TOLL FREE 866 584 5504 FAX 954 584 5556 e amp
Download Pdf Manuals
Related Search