Uniden 1260 Telephone User Manual
Contents
1. Uniden Model 1260 Slimline Memory phone User s guide Uniden AUER E DIAL YY Equipment Approval Information Your telephone equipment is approved for connection to the Public Switched Telephone Network and is in compliance with parts 15 and 68 FCC Rules and Regulations and the Technical Requirements for Telephone Terminal Equipment published by ACTA 1 Notification to the Local Telephone Company On the bottom of this equipment is a label indicating among other information the US number and Ringer Equivalence Number REN for the equipment You must upon request provide this information to your telephone company The REN is useful in determining the number of devices you may connect to your telephone line and still have all of these devices ring when your telephone number is called In most but not all areas the sum of the RENs of all devices connected to one line should not exceed 5 To be certain of the number of devices you may connect to your line as determined by the REN you should contact your local telephone company A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA A compliant telephone cord and modular plug is provided with this product It is designed to be connected to a compatible modular jack that is also compliant See installation instructions for deta2. Pick up the handset and press the dial button 2 Press the a or buttons for the desired memory location 3 Press the dial button to dial the number OR 1 Press dial button while the handset is still in the cradle 2 Press the or buttons for the desired memory location lift the handset and the number dials automatically Reviewing Numbers Stored in Memory 1 Press the store button 2 Press 0 9 for the memory location The number shows on the display Copy Caller ID Memory to User Memory 1 Pickup the handset 2 Press the a or w buttons to display the number you want to copy 3 Press the store button 4 Press 0 9 for the memory location The display flashes if the memory location is occupied 5 Press the store button twice to replace the new information with the old or press the or buttons to select an empty location The number is automatically stored 6 Press the hook switch to exit Copy Redial Memory to User Memory 1 Pickup the handset 2 Press store 3 Press 0 9 for the memory location Press the a or buttons to select a different location The display flashes if the memory location is occupied 4 Press the store button again to confirm 5 Press the redial button and then press the store button again 6 Press the flash button or the hook switch to exit Storing a Pause in Memory The redial button has dual functionality It b
3. the a or w button The display will alternate between the two dialing modes 5 Press the menu button to store the dialing mode and return to the T P DIAL MODE display Exit Setup To immediately exit the setup mode select the EXIT SETUP menu and press the menu button REMINDER The time and date is programmed automatically when the first Caller ID record is successfully received after the unit is setup E Telephone Basics Connecting the Telephone Line 1 Plug the long straight line cord into a modular wall telephone jack 2 Place the handset in the cradle NOTE The unit is properly installed if you pick up the handset and hear the dial tone Otherwise recheck all the installation steps Wall Mount Installation Your telephone may also be mounted on a wall plate not in cluded NOTE To prevent the handset from falling out of the cradle while the phone is hanging on the wall you must reverse the handset hook located on the base 1 Push the handset hook up and out of the slot on the base with your thumb rotate the hook 180 and replace it back in the slot 2 Feed the line cord through the groove and wrap the cord around the track on the bottom of the base 3 Feed the line cord through the groove on the opposite side of the track and plug the end into the modular telephone jack 4 Slip the mounting holes on the bottom of the base over the wall plate posts and firmly slide th
4. 1 digits i e 1 234 555 1234 then the call received was not from your area code 2 Press the dial button and the display shows PICKUP or ADJUST A 10 second timer also starts in the upper right side of the display letting you know the time remaining until the unit returns to the Summary Screen If you adjust the number to be dialed the timer automatically resets itself 3 To adjust the phone number press the dial button For instance a 7 digit local number sometimes cannot be dialed because it requires a 10 digit or 11 digit format Press the dial button repeatedly to scroll through the 7 10 and 11 digit numbers 7 digits 7 digit telephone number i e 555 5555 10 digits 3 digit area code 7 digit telephone number i e 425 555 5555 11 digits long distance code 1 3 digit area code 7 digit telephone number i e 1 425 555 5555 4 To dial the displayed number pick up the handset before the timer reaches 0 NOW DIALING shows in the display and the number is dialed If you did not program your local area code in the setup menu 1 Use the a and buttons to display the number you want to dial You will only see 10 digit numbers i e 234 555 1234 2 See steps 2 through 4 in the above section to complete the dialback sequence NOTE If PICKUP PHONE shows on the display no other changes to the number can be made The information sent from the telephone company is known to be a valid number to dial back a
5. IGHTNING CAUTION TO REDUCE THE f THE EXCLAMATION r FLASH AND ARROW J RISK OF ELECTRIC SHOCK DO WARNING TO HEAD WITHIN THE NOT REMOVE COVER OR PREVENT FIRE OR TRIANGLE IS A BACK NO Us are ELECTRICAL SHOCK i REFER SERVICING TO HAZARD DO NOT DANGEROUS QUALIFIED SERVICE INSTRUCTIONS EXPOSETHIS VOLTAGE INSIDE PERSONNEL ACCOMPANYING THE PRODUCT THE PRODUCT PRODUCT TO RAIN OR MOISTURE SEE MARKING ON BOTTOM BACK OF PRODUCT Introduction CAUTION When using telephone equipment there are basic safety instructions that should always be followed Refer to the IMPORTANT SAFETY INSTRUCTIONS provided with this product and save them for future reference Before You Begin Parts Checklist Make sure your package includes the following items Telephone Jack Requirements To use this phone you need an RJ11C type Wall plate modular telephone jack which might look like o the one pictured here installed in your home Modar 5 elephone If you don t have a modular jack call your line jack local phone company to find out how to get one installed Important Installation Information e Never install telephone wiring during a lightning storm Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations Never touch non insulated telephone wires or terminals unless the telephone line has been disconnected at the network interface Use caution when installing or mod
6. Press the menu button to store the setting and return to the REGIONAL AREA CODE display 8 Press dial to exit CID Language This setting allows you to display Caller ID display prompt messages in English French or Spanish 1 Press the menu button SET OR appears in the display 2 Press the button until CID LANGUAGE appears in the display 3 Press the menu button to show the current language setting The default is English 4 Press the a or button to change the language 5 Press the menu button to store the language and return to the CID LANGUAGE display Select Contrast This adjustment allows you to select the contrast of the display 1 Press the menu button until SET OR appears 2 Press the a button until SELECT CONTRAST appears in the display 3 Press the menu button to show the current contrast setting There are 5 levels of contrast with the default set to 3 4 To decrease the contrast press To increase the contrast press a 5 Press the menu button to store the contrast setting and return to the SELECT CONTRAST display T P Dial Mode This adjustment allows you to select Tone touch tone or Pulse rotary dialing Press the menu button until SET OR appears 2 Press the a button until T P DIAL MODE appears in the display 3 Press the menu button to show the current dial mode The default is set to tone 4 To change the dialing mode press
7. cal phone company such as Call Waiting These services generally require an extra monthly fee If you subscribe to any of these services please refer to the phone company s instructions on how to use flash To answer an incoming call while having a conversation After you hear the Call Waiting tone press and release the flash button The first call is placed on hold while the second call can be answered To return to your first call and put the second call on hold Press and release flash again The first call can continue while the second call is put on hold Using Temporary Tone Dialing If you have pulse service you can temporarily change from pulse to tone service After dialing the telephone number press and release the tone button on the telephone This allows access to phone services that require atone such as banking and long distance services After you hang up the handset the telephone automatically returns to pulse service Caller ID Display Messages The following special messages indicate the status of a message or the unit NO CALLS The caller memory is empty UNKNOWN NAME The incoming call does not have Caller ID service or their service area is not linked to yours If the screen displays UNKNOWN NAME along with a calling number the name information for that number was not available Low Battery power level is low Please replace the batteries as soon as possible in order to maintain Caller ID op
8. can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna that is the antenna for radio or television that is receiving the interference Reorient or relocate and increase the separation between the telecommunications equipment and receiving antenna Connect the telecommunications equipment into an outlet on a circuit different from that to which the receiving antenna is connected If these measures do not eliminate the interference please consult your dealer or an experienced radio television technician for additional suggestions Also the Federal Communications Commission has prepared a helpful booklet How To Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington D C 20402 Please specify stock number 004 000 00345 4 when ordering copies Notice The changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Visit our Website at www uniden com Uniden Model 1260 Printed in China Uniden America Corporation Ft Worth TX e Hearing Aid Compatibility HAC This telephone system meets FCC standards for Hearing Aid Compatibility Licensing Licensed under US Patent 6 427 009 CAUTION DONOT OPEN THE L
9. d you may also have other rights which vary from state to state This warranty is void outside the United States of America and Canada PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY If after following the instructions in the owner s manual you are certain that the Product is defective pack the Product carefully preferably in its original packaging The Product should include all parts and accessories originally packaged with the Product Include evidence of original purchase and a note describing the defect that has caused you to return it The Product should be shipped freight prepaid by traceable means to warrantor at Uniden America Service 4700 Amon Carter Blvd Fort Worth TX 76155
10. e unit down into place Adjusting the Ringer Volume You may control the ringer volume level with the switch located on the side of the base 2 ringer tone will be loud 1 ringer tone will be low J telephone will not ring Adjusting the Volume You may control the listening level with the VOLUME switch which has three levels It remains at the last level set until you change it Redialing a Number If you want to call the last number you dialed again up to 32 digits use the redial feature 1 Pick up the handset 2 Press the redial button 3 The last number called is automatically redialed Using One Touch Redial If the last call you dialed was busy you can redial it immediately by just pressing the redial button and without hanging up the handset Caller ID CID IMPORTANT In order to use this unit s Caller ID features you must subscribe to either the standard Name Number Caller ID Service or Call Waiting Caller ID Service To know who is calling while you are on the phone you must subscribe to Call Waiting Caller ID Service This unit receives and displays information transmitted by your local phone company This information can include the phone number date and time or the name phone number date and time New calls Current date Current time Caller ID number Caller ID name Call Waiting Caller ID Provided you subscribe to Call Waiting Caller ID service form your phone compa
11. ecomes a pause but ton if the store button is pressed first It is valid only when storing a number into memory Use the redial button to insert a pause when a delay is needed in an automatic dialing sequence For example when you must dial a 9 to get an outside line or when you enter codes to access your long distance company You may need to adjust the length of the pause It can be adjusted from 1 to 9 seconds The default setting is 4 seconds Pickup the handset Press the store button Press the redial button 1 2 3 4 Press 1 9 1 1 second 2 2 seconds etc 5 Press store again 6 Press the flash button or the hook switch to exit Chain Dialing This process allows you to dial a succession of stored numbers from separate memory locations This is useful when you must dial several sequences of numbers such as with frequent calls via a telephone company long distance provider For example Memory location Local access number of long distance company 6 Authorization code ID 7 Long distance phone number 8 1 Pick up the handset 2 Press the mem button and then press 6 3 When you hear the access tone press the mem button and then press 7 4 At the next access tone press the mem button and then 8 TIP Wait for the access tones before pressing the next mem button or your call may not go through Using Flash This feature is used to activate customer calling services available through your lo
12. eration PRIVATE NAME The incoming caller is registered as Private Number and Caller ID information is withheld START END You are at the beginning or the end of the Caller ID memory log If you subscribe to Call Waiting Caller ID Service this icon flashes when you receive a call while you are on the phone REPT Repeat call message indicates that a new call from the same number was received more than once NEW Indicates call of calls have not been reviewed Troubleshooting Tips No Dial Tone e Check all cabling to make sure that all connections are secure and not damaged e Check hook switch Does it fully extend when handset is lifted from cradle No Display e Replace the batteries Make sure the batteries are properly installed No Information is shown after the phone rings In order to receive Caller ID records you must subscribe to the standard name and number Caller ID service available through your local telephone company e Be sure to wait until the second ring before answering Phone does not ring e Make sure the ringer switch is set to 1 or 2 You may have too many extension phones on your line Try unplugging some extension phones e Check for dial tone See Troubleshooting Tips for No Dial Tone Other parties cannot hear you Make sure phone cord is securely plugged in Make sure extension phones are on the hook at the same time you re using the phone It s normal for the volume to dro
13. f Part 68 FCC Rules and Regulations The telephone company may make changes in its communications facilities equipment operations or procedures where such action is required in the operation of its business and not inconsistent with FCC Rules and Regulations If these changes are expected to affect the use or performance of your telephone equipment the telephone company must give you adequate notice in writing to allow you to maintain uninterrupted service Interference information This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation Privacy of Communications may not be ensured when using this product This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which
14. han an authorized Uniden service center for a defect or malfunction covered by this warranty E used in any conjunction with equipment or parts or as part of any system not manufactured by Uniden or F installed or programmed by anyone other than as detailed by the owner s manual for this product STATEMENT OF REMEDY In the event that the product does not conform to this warranty at any time while this warranty is in effect warrantor will either at its option repair or replace the defective unit and return it to you without charge for parts service or any other cost except shipping and handling incurred by warrantor or its representatives in connection with the performance of this warranty Warrantor at its option may replace the unit with a new or refurbished unit THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER WHETHER EXPRESS IMPLIED OR ARISING BY OPERATION OF LAW INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES Some states do not allow this exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you LEGAL REMEDIES This warranty gives you specific legal rights an
15. ifying telephone lines Handset Layout tone button store button mem memory button flash button redial button Handset Back volume switch delete A button Uniden display a v buttons dial button button Installing and Replacing the Batteries IMPORTANT You will have approximately 60 seconds to replace the batteries before the memories stored in the handset are lost Please read the instructions before replacing the batteries and have the batteries ready to be inserted beforehand As a precaution you may want to write down any stored information you do not want erased Your Caller ID phone uses 3 AA size alkaline batteries for receiving and storing Caller ID records and for the numbers you use for memory dialing 1 If the telephone line cord is connected disconnect it from the wall 2 Open the battery compartment door with your finger or thumb Battery compartiment 3 Insert 3 AA size alkaline batteries not included as shown on the diagram inside the compartment 4 Replace the battery compartment door 5 Re attach the line cord to the wall and check your memory locations If installation takes longer than 60 seconds you should re set your memory locations IMPORTANT If you re not going to use the telephone for more than 30 days remove the batteries because they can leak and damage the unit Setting Up the Caller ID Menu IMPORTANT Do not pl
16. ils Notes This equipment may not be used on coin service provided by the telephone company Party lines are subject to state tariffs and therefore you may not be able to use your own telephone equipment if you are on a party line Check with your local telephone company Notice must be given to the telephone company upon permanent disconnection of your telephone from your line If your home has specially wired alarm equipment connected to the telephone line ensure the installation of this product does not disable your alarm equipment If you have questions about what will disable alarm equipment consult your telephone company or a qualified installer US Number is located on the cabinet bottom REN Number is located on the cabinet bottom 2 Rights of the Telephone Company Should your equipment cause trouble on your line which may harm the telephone network the telephone company shall where practicable notify you that temporary discontinuance of service may be required Where prior notice is not practicable and the circumstances warrant such action the telephone company may temporarily discontinue service immediately In case of such temporary discontinuance the telephone company must 1 promptly notify you of such temporary discontinuance 2 afford you the opportunity to correct the situation and 3 inform you of your right to bring a complaint to the Commission pursuant to procedures set forth in Subpart E o
17. nding order 5 Press the menu button to advance to the next digit 6 After the 3rd and last digits entered press the menu button to store the area code and go to the next setting NOTE If you make a mistake you can simply repeat the previous steps until your area code is set Regional Area Codes for 10 Digit Dialing Like the Local Area Code the telephone uses the programmed area codes to determine the number format to display when a valid Caller ID signal is received Calls that match any of the programmed regional area codes are displayed as 10 digits This is helpful in areas that have multiple or overlapping area codes and require 10 digit dialing 1 Press the menu button SET OR appears in the display 2 Press the a button until REGIONAL AC S 1 shows in the display 3 To enter or change the area code press the menu button The display shows the area code stored in memory The left most digit or minus sign flashes indicating the unit is ready to accept the area code entry 4 Press the button and select a number from 9 0 for the first digit of the are code 5 When the desired digit is flashing press the button to advance to the next digit 6 Press the menu button again to enter the next three digit regional area code and repeat steps 4 and 5 until all the REGIONAL AC S 1 RAC 1 and REGIONAL AC S 2 RAC 1 are entered A total of 6 sets of Regional Area Codes may be entered 7
18. nifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met It does not imply that Industry Canada approved the equipment NOTICE The Ringer Equivalence Number REN for this terminal equipment is marked on the equipment itself The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five One year limited warranty IMPORTANT Evidence of original purchase is required for warranty service WARRANTOR UNIDEN AMERICA CORPORATION Uniden ELEMENTS OF WARRANTY Uniden warrants for one year to the original retail owner this Uniden Product to be free from defects in materials and craftsmanship with only the limitations or exclusions set out below WARRANTY DURATION This warranty to the original user shall terminate and be of no further effect 12 months after the date of original retail sale The warranty is invalid if the Product is A damaged or not maintained as reasonable or necessary B modified altered or used as part of any conversion kits subassemblies or any configurations not sold by Uniden C improperly installed D serviced or repaired by someone other t
19. ny if you receive an incoming call and you are using Uniden s multi handset system a beep indicates the presence of a Call Waiting call on the line The Call Waiting Caller ID information will be displayed and stored in the history of all handsets in the system When you hear the call waiting beep in the handset receiver press the flash button to put the current call on hold and answer the incoming call Press flash again to return to the original call Receiving CID Records When you receive a call the Caller ID information is transmitted between the first and second ring The Caller ID information appears on the display while the phone rings giving you a chance to monitor the information and decide wheather or not to answer the call Storing CID Records In CID Memory If you are not at home or cannot answer your telephone s Caller ID memory stores the data for the 50 most recent calls you received so you can see who called while you were unavailable When the 51st call is received the oldest Caller ID record 1st call is automatically deleted You may review the stored information at any time Calls received since your last review show as NEW in the display Calls that have not been previously reviewed but were received from the same number more than once show as REPT in the display Reviewing CID Records As calls are received and stored the display is updated to let you know how many calls have been received To sc
20. p when additional extension phones are used at the same time Cannot dial out e Make sure the T P dialing mode is set to the type of phone service you are subscribed to Service If trouble is experienced with this equipment for repair or warranty information please contact customer service at 1 800 297 1023 If the equipment is causing harm to the telephone network the telephone company may request that you disconnect the equipment until the problem is resolved This product may be serviced only by the manufacturer or its authorized service agents Changes or modifications not expressly approved by Uniden America Corporation could void the user s authority to operate this product For instructions on how to obtain service refer to the warranty included in this guide or call customer service at 1 800 297 1023 Or refer inquiries to Uniden America Service 4700 Amon Carter Blvd Forth Worth TX 76155 Attach your sales receipt to the booklet for future reference or jot down the date this product was purchased or received as a gift This information will be valuable if service should be required during the warranty period Name of Store Purchase Date Industry Canada I C Notice Terminal equipment NOTICE This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications This is confirmed by the registration number The abbreviation IC before the registration number sig
21. roll CID records 1 Press either the a or down button to view the newest call record 2 Press the button to scroll through the call records from the most recent to the oldest 3 Press the a button to scroll through the call records from the oldest to the newest 4 When all of the messages have been viewed START END appears in the display Deleting CID Records To delete the record showing in the display press the delete button once To delete all records while reviewing press and hold the delete button until ERASE ALL shows in the display then press the delete button again to confirm Dialing Back When reviewing Caller ID records you may dialback the phone numbers shown on the display by pressing the dial button NOTE Depending on a how the incoming caller s phone number is formatted when it is received and b whether or not you previously pre programmed your local area code into the set up menu you may need to adjust the format of the incoming caller s stored phone number before making the call press the dial button to adjust the number and try again If you programmed your local area code in the setup menu 1 Use the and buttons to scroll to the number you want to dial If you see a number with 7 digits i e 555 1234 then the call was received from within your area code However this does not guarantee the call is a local call If you see a number with 1
22. ug the telephone into the wall jack while setting up the Caller ID menu because an incoming call may invalidate the information not yet saved Place the handset in the cradle on the base 2 Press the menu button SET OR appears in the display 3 Press either or button to scroll among the 7 menu screens which are eSET a OR Local Area Code default e Regional AC s 1 default CID LANGUAGE default English SELECT CONTRAST default 3 T P DIAL MODE default tone EXIT SETUP NOTE You may press dial anytime to exit the Caller ID Set Up menu If no buttons are pressed within 10 seconds the phone automatically exits the Caller ID Set Up menu and returns to the NO CALLS summary screen Local Area Code The telephone uses the programmed area code to determine the number format to display when a valid Caller ID signal is received It is also used for the Dialback feature 1 Press the menu button SET a OR appears in the display 2 Press the button until LOCAL AREA CODE ___ appears in the display 3 To enter or change the area code press the menu button The display shows the area code stored in memory The left most digit ora minus sign flashes indicating the unit is ready to accept the area code entry 4 Press the button and select a number from 0 9 in ascending order Or press the button to select numbers from 9 0 in desce
23. vailable only in limited areas Once you pickup the phone the number is automatically dialed Memory Before you store a telephone number in memory make sure the dialing mode is correctly set for the type of service you have The default dialing mode is tone touch tone so if you have pulse rotary service you must first change the dialing mode See T P Dial Mode Storing Frequently Called Numbers 1 Pick up the handset 2 Press the store button 3 Push the desired memory location button 0 9 4 Press the store button 5 Use the handset number keys to enter the telephone number up to 16 digits and press the store button 6 Hang up the handset NOTE If you make a mistake use the delete button to delete wrong digits Changing a Stored Number Repeat the storage sequence above The new number replaces the old number at the memory location Erasing a Stored Number 1 Pick up the handset 2 Press the mem button 3 Press the a or w buttons for the desired memory loca tion to be erased 4 Press and hold delete for three seconds until the number in the display is erased 5 Hang up the handset NOTE If you want to erase more than one location use the a or arrow buttons to scroll to each memory location you want to erase Dialing Frequently Called Numbers 1 Pick up the handset and press the mem button 2 Press 0 9 for the memory location The number dials automatically OR
Download Pdf Manuals
Related Search