Ultra Start 600 Series Automobile Alarm User Manual
Contents
1. Test for door pin type Positive or Negative then connect the appropriate wire Green or Purple Step 2 Plug In The Module When all the connections are done the control module can be plugged in Before connecting the control module make sure the ignition is in the OFF position Plug in the 6 pin harness then the 14 pin followed by any other connectors that were used Step 3 Program Test And Adjust The Shock Sensor To program the Shock Sensor 1 Press and release Lock button Five times 2 The system will chirp and the park lights will flash three times then stay ON 3 Within 10 seconds impact vehicle in a safe place i e Window pillar with amount of force wanted to activate alarm The siren will chirp upon learning the impact 4 The Shock Sensor is now programmed 5 Press the Unlock button to exit the Program Mode To test the Shock Sensor 1 Press the Lock button once to arm the system 2 Wait five seconds then impact the vehicle Lighter impacts to the vehicle should trigger the warn away The siren will chirp three times A harder impact to the vehicle will trigger the full alarm The siren will activate for 60 seconds then turn off 3 To deactivate the alarm when triggered press the unlock button twice To adjust the Shock Sensor 1 Repeat the shock sensor learning If the sensor was to sensitive impact the vehicle with greater force If the sensor was not sensitive enough impact the vehicle wit2. INSTALL GUIDE 600 Series Remote Vehicle Security System REMOTE STARTERS CAR ALARMS WWW ULTRASTARTERS COM Technical Support Note Some features may not be available on certain models FCC ID Notice This device complies with Part 15 of the FCC rules Operation is subject to the following conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation CAUTION Changes or modifications not expressly approved by the part responsible for compliance void the user s authority to operate this devise INSTALL GUIDE SECURITY SYSTEM PAGE 2 Table of Contents Table of Contents Page 2 Components 600 Wiring Diagram Page 3 Installation Tips Page 4 Pre Installation Suggestions Installation Suggestions Page 4 Mounting The Module Installing The LED Installing The Program Button Connecting The Starter Disable Connecting The Dome Light Supervision Under Hood Connections Mounting The Siren Wire Connectors Page 5 14 Pin Main Harness Connector 4 Pin Red Connector Keyless Entry 2 Pin Connector Red Plug in LED 2 Pin Blue Connector Plug in Program Button 3 Pin White Connector Aux outputs 4 Pin White Connector Additional sensor input Installation Page 6 7 Basic Installation Quick start Shock Sensor Programming Test The System Programming Page 7 9 Program Overview amp System Reset
3. Lock User Options Page 8 Press Button 2 Unlock Alarm Settings Page 9 6 The selected mode will be confirmed by a siren chirp and one park light flash 7 The Program Menu may be changed at any time by pressing the transmitter buttons as above this allows the installer to change a setting from one menu then quickly jump to another menu and change another setting without exiting Program Mode 8 Program Mode will be exited if there is no activity for 30 second or if the key is turned to the Off position This will be confirmed by one siren chirp and park light flash Note f unit does not enter Program Mode turn ignition off and repeat steps 1 4 The ignition wire Yellow MUST be connected to the vehicle s ignition wire If it is not connected it will not be possible to enter the Program Modes Changing the Programmable Settings To Select and Change A Program Setting 1 Enter Program Mode 2 Select the desired Program Menu See pages 8 amp 9 3 Press amp release the Program Button the correct number of times to select the desired Program Setting as listed on pages 8 amp 9 The park lights will flash and the siren will chirp to indicate the current setting that is selected 4 Press and hold the Program Button until the parking lights siren confirm the selected setting The park lights will flash and the siren will chirp to indicate the option selected within the setting 5 Turn the ignition key Off to exit Program
4. See page 5 Negative output when system is armed Positive trunk release 5 00ma max Input from vehicles ignition wire System ground input Constant 12 Volt input Programmable menu 1 setting 3 Output for voltage inverter Low Current Only Programmable menu 1 setting 3 Programmable menu 1 setting 3 The program Button is used to access the systems Programming Menu s See page 5 for installation instructions 2 Pin Connector Red Plug in LED Connector See page 5 for installation instructions 3 Pin Connector White Green When Disarmed Pink Horn Channel 5 Blue Disconnect 4 Pin Connector White Blue Sensor Full Warn Green Sensor Pre Warn Black Ground Output Red 12 Volt Output Negative output when disarmed Programmable See menu 2 setting 7 Triggers when 12volt circuit is broken Input trigger for addition alarm sensor s Input trigger for addition alarm sensor s Ground output for addition alarm sensor s 12 volt output for additional alarm sensor s INSTALL GUIDE SECURITY SYSTEM PAGE 6 Quick Start Install Step 1 Connect All Of the Following Wires 14 Pin Power Connector Black Ground Input System ground input Yellow Ignition Input Input from vehicles ignition wire Red MainPower Input Positive output for siren White Park lights Programmable menu 2 setting 3 Green Door Input Negative door pin switch input Purple Door Input Positive door pin switch input
5. be confirmed by 2 LED flashes Press and hold the Valet Switch until you receive the appropriate of park light flashes and or siren chirps Release the Valet Switch Press the Valet momentarily to move to next program step or repeat to change selection Setting 3 Door Lock Options 1 Double Pulse Unlock 1 Flash Single 75 second lock and double unlock pulse 2 3 Second Lock amp Unlock 2 Flashes 3 second pulses for lock amp unlock 3 0 75 Second Pulses 3 Flashes 0 75 second pulses for lock and unlock Press the Valet Switch 3 times to select setting 3 This will be confirmed by 3 LED flashes Press and hold the Valet Switch until you receive the appropriate of park light flashes and or siren chirps Release the Valet Switch Press the Valet momentarily to move to next program step or repeat to change selection Setting 4 Sensor Enable Disable 1 Sensors Disabled 1 Flash Shock sensor and Aux Sensor disabled 2 Sensors Enabled 2 Flashes Shock Sensor and Aux sensor enabled Press the Valet Switch 4 times to select setting 4 This will be confirmed by 4 LED flashes Press and hold the Valet Switch until you receive the appropriate of park light flashes and or siren chirps Release the Valet Switch Press the Valet momentarily to move to next program step or repeat to change selection Setting 5 Passive Active Arming 1 Passive Arming 1 Flash Auto Arms 30 seconds after last door is closed 2 Active Arming With Rearm 2 Flashes Unlock
6. ED status will be cleared when ignition is turned ON For proper memory clearing insure to connect the ignition input to the ignition on the vehicle Diagnostics Chart Park Light Flashes LED Flashes Diagnostic Two Flashes Two Flashes Shock Sensor Triggered Three Flashes Three Flashes Door Input Triggered Four Flashes Four Flashes Ignition Input Triggered Five Flashes Five Flashes Hood Input Triggered None Off System Disarmed None On Solid Valet Service Mode None Single Flashes System Armed None Rapid Flashes Passive Arming On Off Rapid Flashes Car Jack Mode Additional LED Flashes Note While the system is disarmed and the ignition is in the off position the LED will activate from the following triggers 1 The Door is opened The LED will Stay on until the door is closed 2 The Hood is opened The LED will stay on until the hood is closed 3 The Shock Senor The LED will flash when impact is detected 4 The Aux Sensor The LED will flash when the input is triggered
7. Mode SYSTEM RESET STEP 1 Within three seconds turn the key ON OFF ON OFF ON Leave the Key ON STEP 2 Press and release the Program Button STEP 3 Park Lights will come ON STEP 4 Press the Program Button a second time and hold for 8 seconds until the park lights flash 3 times and siren chirps 3 times System is now re set to factory defaults NOTE Reset to defaults does not delete the transmitters from memory INSTALL GUIDE SECURITY SYSTEM PAGE 8 Menu 1 User Settings Setting 1 Ignition Auto Lock 1 Ignition Lock amp Unlock Enabled 1 Light Flash Doors Lock Unlock when the key is turned On Off 2 Ignition Lock Only 2 Light Flashes Doors Lock when ignition key is turned ON only 3 Ignition Auto Lock Disabled 3 Light Flashes Doors do not Lock or Unlock with Ignition key Press the Valet Switch 1 time to select setting 1 This will be confirmed by 1 LED flashes Press and hold the Valet Switch until you receive the appropriate of park light flashes and or siren chirps Release the Valet Switch Press the Valet momentarily to move to next program step or repeat to change selection Setting 2 Horn Honk Settings 1 Lock amp Unlock chirps Disabled 1 Flash A audible chirp for Panic Mode only 2 Lock amp Unlock chirps Enabled 2 Flashes Chirp for Lock amp Unlock but NO indication for Start 3 Chirps Enabled 3 Flashes Chirp indication for Lock Unlock and Start Press the Valet Switch 2 times to select setting 2 This will
8. Output 7 500ma Output 500ma Output Priority Output i LED a Negative Output When Disarmed 500ma Output Green Programmable See menu 2 Setting 7 500ma Output Horn Channel 5 Triggers when 12vt circuit is broken 500ma Input Disconnect Negative trigger input 500ma Input sensor Full Warn Negative trigger input 500ma Input Sensor Pre Warn gt D g D 9 ap i 3 D Q ms a Sensor ground output 500ma Output Sensor Ground 500ma Output Sensor Power m Sensor power output 500ma outputs are low current and are designed to activate relays SATELLITE LINK PLUG lc Pte INSTALL GUIDE SECURITY SYSTEM PAGE 4 Recommended Pre Installation Procedures BEFORE STARTING INSTALLATION Discuss the optional system features with the customer Take a few minutes to review the installation and owners manuals Do a walk around the vehicle and check for any damage If installing a LED discuss the placement with customer before installing Recommended Installation Procedures Mounting the Module Never mount the module in the engine compartment Select a location under the dash to install the main module Be certain that the module is securely attached and does not obstruct any serviceable areas Mount the module so that it cannot be seen if looking under the dash as it could be easily unplugged by a thief The module must be free from all moving parts such as brake clut
9. Program Menu 1 User Settings Program Menu 2 Alarm Settings Operations Page 10 Single amp Dual Car Operation Transmitter Programming Battery Replacement Other Features Page 11 System Service Mode Service Mode By remote Diagnostics Page 12 Components Control module Starter Disable harness Remote transmitter s Plug in Valet Switch 14 pin main harness with 4 pin Aux sensor harness dual 30amp power inputs Plug in Led 4 pin Keyless Entry harness with Multi tone siren Driver s Door Priority output Installation and owner manuals SECURITY SYSTEM INSTALL GUIDE PAGE 3 Wiring Diagram 500ma Output Channel 4 Programmable Menu 2 tl jolie Nor _ _ S515 5 co s Dy yel te a aa Connect to door pin Door Input 3amp Output Connect to hood pin Hood Input Connect to door pin Door Input Connect to Siren Siren l 15amp Output Park Lights ome Light Relay BIk White BIk White Connect to park lights See page 4 Input Output Dome Light Relay When Armed Trunk Release gnition Input Yellow See page 4 Output while armed 500ma Output Trunk Release Output Connect to main Ignition SSoUIeH Wwsely uely m Ol 10 5 gt 13 2 commen Cc la O Cc mr Connect to chassis ground Input Z ee w D v O g p 12vt constant power 500ma
10. ch and gas pedals linkages Installing The Led Choose a location that will be highly visible when the LED is installed Most vehicles are equipped with knock out panels in the dashboard these panels are easily removable and can be easily replaced if necessary Once the location is picked use a 5 16th drill bit and drill a hole through the panel Test fit the LED into the hole If the hole was drilled to large place the LED in the hole and glue in place from the back of the panel Plug the Led into the Red connector on the main module Installing The Program Button Choose a location to mount the Program Button This location should be hidden and not visible from outside the vehicle Once the location of the switch is picked use a 1 4 drill bit and drill a hole Remove the nut and push the Program button through the hole Replace the nut and tighten until the switch is secure Plug the valet into the Blue connector Connecting The Starter Disable This system contains a built in Starter disable relay The brown starter kill wire from the wire harness bag will connect to the module as normally connected 87a amp 30 Cut the brown wire in half then locate the vehicles starter wire This wire will switch to 12volts in the crank or start position only Cut this wire in half and confirm that the vehicle will not start Connect the brown wires one to each side of the cut starter wire Route the brown wires to the main module and connect Co
11. ge selection Setting 7 Horn 5th Channel 1 5th Channel 1 Flash Pulsed output when activated by button 4 2 Horn Honk 2 2 Flashes Horn Honk Output Full Alarm ONLY 3 Horn Honk 1 3 Flashes Horn Honk with Arm amp Disarm Chirps INSTALL GUIDE SECURITY SYSTEM PAGE 10 First Car Operation Press Once to Lock the doors and arm the alarm Hold for Panic Mode Press a second time and hold for Constant Lock Output a Press once to unlock the doors and disarm the alarm Press and hold for the Trunk Aux Output gt sk Press this button to activate the 4th channel output First Car This output can be used to activate additional alarm features Press once and hold for Car Finder Press and release then hold to activate deactivate Service Mode Second Car Operation Optional Press Once to Lock and arm the alarm Hold for Panic Mode FE amp Press a second time and hold for Constant Lock Output Press once to unlock the doors and disarm the alarm gap amp A Press and hold for the Trunk Aux Output Press this button to activate the 4th channel output 2nd Car a05 amp K This output can be used to activate additional alarm features gop tt Sop Press once and hold for Car Finder n ii Press and release then hold to activate deactivate Service Mode Transmitter Programming Step 1 Within three seconds turn the ignition ON OFF ON OFF ON Leaving ON Step 2 Press and hold the Program Switch Parking Lights will co
12. h less force For best results ensure that the Control Module is mounted securely to the vehicle Test The System 1 Open all the vehicles windows 2 Press the Lock button to arm the system 3 Wait five seconds or until the dome light goes out then reach in through a window and open the door The alarm will then activate repeat on all the doors 4 Test the Shock Sensor again and adjust if necessary 5 Insure that all additional features are working as intended 6 If necessary proceed to Program Mode to adjust the programmable outputs Your Basic Install Is Complete SECURITY SYSTEM INSTALL GUIDE PAGE 7 Programming Overview Program mode allows you to adjust the settings and options of your system Your system has been intelligently designed by installers with years of experience The system s default settings do not require any program changes in most cases However this system does incorporate a highly advanced programming system that includes 2 menus with numerous options and settings that can be easily adjusted for custom installations and applications Entering Program Mode To Enter Program Mode 1 Make sure ignition is in the off position 2 Within three seconds turn the key ON OFF ON OFF ON Leave Key ON 3 Press and release the Program Button one time 4 Park lights will come and the siren will chirp to confirm entering Program Mode 5 Select Desired Program Menu by the following Press Button 1
13. is pressed and no door is within 30 sec 3 Active Arming 3 Flashes Alarm arm by remote transmitter only Press the Valet Switch 5 times to select setting 5 This will be confirmed by 5 LED flashes Press and hold the Valet Switch until you receive the appropriate of park light flashes and or siren chirps Release the Valet Switch Press the Valet momentarily to move to next program step or repeat to change selection Setting 6 Active Passive Locks 1 Active Locking 1 Flash Doors do not auto lock with passive arming 2 Passive Locks 2 Flashes Doors Auto Lock with passive arming Press the Valet Switch 6 times to select setting 6 This will be confirmed by 6 LED flashes Press and hold the Valet Switch until you receive the appropriate of park light flashes and or siren chirps Release the Valet Switch Press the Valet momentarily to move to next program step or repeat to change selection SECURITY SYSTEM INSTALL GUIDE PAGE 9 Menu 2 Alarm Settings Setting 1 Car Finder 5th Channel 1 Car Finder OFF 1 Light Flash Car Finder Mode Disabled 2 Car Finder ON 2 Light Flashes Car Finder Mode Enabled To operate the 5th channel on button 4 setting 7 must be programmed for 5th channel output Press the Valet Switch 1 time to select setting 1 This will be confirmed by 1 LED flashes Press and hold the Valet Switch until you receive the appropriate of park light flashes and or siren chirps Release the Valet Switch Press the Valet
14. l Alarm the system will no longer respond to the transmitters and the starter disable output will activate to disable the vehicle from starting ACTIVATING CAR JACK MODE Program Menu 2 Setting 5 Type 1 Car Jack Mode will activate if the door is opened while the ignition key is in the On position Car Jack Mode may also be activated by pressing the button on the remote transmitter while the ignition key is in the On position Type 2 Car Jack Mode will activate if the ignition key is turned to the On position Car Jack Mode may also be activated by pressing the button on the remote transmitter while the ignition key is in the On position DEACTIVATING CAR JACK MODE 1 During the Countdown Mode Turn the ignition key ON then press and release the Program Button one time 2 After Full Alarm Turn the ignition key Off then ON then press and hold the Program Button until the alarm turns off About Eight seconds INSTALL GUIDE SECURITY SYSTEM PAGE 12 Diagnostics Alarm Diagnostics If the alarm system is triggered while armed the system will retain in memory the cause of the trigger The diagnostics can then be used to determine what the cause of the trigger was When disarming the alarm the siren horn will chirp 3 times instead of the usual 2 times to indicate the alarm had been triggered The system s LED will also flash in pulses to indicate which input triggered the alarm NOTE L
15. me ON if park lights do not come on at this point turn key off for 5 seconds then repeat step 1 Step 3 Continue to hold the Program Switch until park lights go out Step 4 Press the LOCK button on each of 1st car remote s and press the button on Each of the 2nd car remote s of the transmitters to be programmed The park lights will Flash once and the siren will chirp once each time a new code is learned Note Transmitter programming must done quickly Do not pause more than one second between each transmitter All the transmitters to be used must be programmed at the same time All transmitters not programmed at this time will be erased from memory for security The system holds a maximum of 3 transmitter codes including 2nd car remote codes You can program the same remote as a 1st car remote in one vehicle and as a 2nd car remote in a second vehicle Battery Replacement The transmitter battery should be changed at least once every year to maintain proper operating range Replace with quality23A 12volt Alkaline battery i A _ Carefully remove Remove top case Replace top case Test remote for the screw from then replace the Re install screw proper operation back of the remote battery SECURITY SYSTEM INSTALL GUIDE PAGE 11 System Service Mode ACTIVATING SERVICE MODE 1 While the ignition is ON press and hold the Program Button for five seconds The park lights will flash and the siren will chirp five time
16. momentarily to move to next program step or repeat to change selection Setting 2 Secure Valet Mode 1 Secure Valet Active 1 Flash Ignition ON and valet switch held for 15 seconds 2 Normal Valet Active 2 Flashes Ignition ON and valet switch held for 5 seconds Press the Valet Switch 2 times to select setting 2 This will be confirmed by 2 LED flashes Press and hold the Valet Switch until you receive the appropriate of park light flashes and or siren chirps Release the Valet Switch Press the Valet momentarily to move to next program step or repeat to change selection Setting 3 Park Light Output 1 Parking Lights on Disarm 1 Flash Park Lights on for 30 seconds on disarm 2 Negative Park Light 2 Flashes Switches Park Light and the Trunk Release outputs 3 Normal Parking Lights 3 Flashes 2 Park Light Flashes on disarm Press the Valet Switch 3 times to select setting 3 This will be confirmed by 3 LED flashes Press and hold the Valet Switch until you receive the appropriate of park light flashes and or siren chirps Release the Valet Switch Press the Valet momentarily to move to next program step or repeat to change selection Setting 4 Horn Honk Timing 1 Sms Pulsed Output 1 Flash Short Quiet Pulses 2 20ms Pulsed Output 2 Flashes Long Loud Pulses 3 10ms Pulsed Output 3 Flashes Normal Medium Pulses Press the Valet Switch 4 times to select setting 4 This will be confirmed by 4 LED flashes Press and hold the Vale
17. nnecting The Dome Light Supervision Determine the door pin type Positive door pin wire switches to 12 volts when the door is opened Negative door pin wire switches to ground when the door is opened For positive door connect one of the black white wires to 12volts and the other to the door pin wire For negative connect one of the black white wires to ground and the other to the door pin wire Mounting The Siren Choose a location in the engine compartment that is away from high heat sources and direct exposer to water The siren should be mounted as well as grounded to solid metal Run the wiring for the siren so that it can not be seen or reached from below the vehicle SECURITY SYSTEM 14 Pin Connector Pink Channel 4 Output Green Door Input Blue Hood Input Purple Door Input Brown Siren Output White Park lights Blk White Dome Light Blk White Dome Light Orange When Armed Grey Trunk Release Yellow Ignition Input Black Ground Input Red Main Power Input 4 Pin Connector Red Green Door Lock Red 12 Volt Output Blue Door Unlock Pink Second Unlock 2 Pin Connector Blue Plug in Program Button Connector INSTALL GUIDE PAGE 5 Programmable See menu 2 setting 5 Negative door pin switch input Negative input from hood pin switch Positive door pin switch input Positive output for siren Programmable menu 2 setting 3 Dome light supervision See page 5 Dome light supervision
18. s to confirm that the system is in Service Mode 2 While in Service Mode the remote start functions will be disabled and LEDs will be ON steady Door locks and trunk release are still operational DEACTIVATING SERVICE MODE 1 While the ignition is ON press and hold the Program Button for five seconds The park lights will flash and the siren will chirp two times to confirm that the system has exited Service Mode 2 Remote start functions will return to normal operation Ai Service Mode By Remote SERVICE MODE ACTIVATED 1 Press and release button 4 then hold Button 4 again for 6 seconds until status LED comes on solid NOTE The siren will chirp 5 times as confirmation SERVICE MODE DEACTIVATED 1 Press and release button 4 then hold Button 4 again for 6 seconds until status LED turns of NOTE The siren will chirp 2 times as confirmation Anti Car Jacking Mode Only program this feature if it specifically requested by the customer Ensure that user is fully trained on the operation of this feature When car jack mode is activated the system will no longer respond to the remote transmitters If the starter disable feature was installed the vehicle will not start When the Car Jack Mode is activated the system will start flashing the LED rapidly for five seconds The park lights and siren will then activate once every second for 10 seconds in Countdown Mode After 10 seconds the alarm will trigger into Ful
19. t Switch until you receive the appropriate of park light flashes and or siren chirps Release the Valet Switch Press the Valet momentarily to move to next program step or repeat to change selection Setting 5 4th Channel Settings 1 Pulsed Output 1 Flash Pulsed for 0 75 seconds upon 4th Channel Activation 2 Latched Output 2 Flashes Latched until repeated or ignition ON 3 Active Output 3 Flashes Active for as long as the button is held on Transmitter Press the lock and Star buttons together to activate the 4th Channel output The Shock Sensor and ignition will be bypassed upon 4th channel activation Press the Valet Switch 5 times to select setting 5 This will be confirmed by 5 LED flashes Press and hold the Valet Switch until you receive the appropriate of park light flashes and or siren chirps Release the Valet Switch Press the Valet momentarily to move to next program step or repeat to change selection Setting 6 Car Jack Mode 1 Type 1 1 Flash Press button 4 or open the door while the Ignition is ON 2 Type 2 2 Flashes Press button 4 or by turning the Ignition On 3 Car Jack OFF 3 Flashes No Car Jack Functions Press the Valet Switch 6 times to select setting 6 This will be confirmed by 6 LED flashes Press and hold the Valet Switch until you receive the appropriate of park light flashes and or siren chirps Release the Valet Switch Press the Valet momentarily to move to next program step or repeat to chan
Download Pdf Manuals
Related Search