U-Line BI2015 Ice Maker User Manual
Contents
1. IMPORTANT PLEASE READ all instructions completely before attempting to install or operate the unit e This unit requires connection to the water supply Improper hook up can result in substantial property damage If you are unsure of your ability to safely connect the water supply to the unit consult a licensed plumber for assistance This unit requires connection to a grounded three prong polarized receptacle that has been placed by a qualified electrician in accordance with applicable electrical codes Safety Alert Definitions Safety items throughout this guide are labeled with a Danger Warning or Caution based on the risk type A DANGER Danger means that failure to follow this safety statement will result in severe personal injury or death A WARNING Warning means that failure to follow this safety statement could result in serious personal injury or death A CAUTION Caution means that failure to follow this safety statement may result in minor or moderate personal injury property or equipment damage 02 2005 General Precautions Use this appliance for its intended purpose only and follow these general precautions along with those listed throughout this guide N WARNING SHOCK HAZARD Electrical Grounding Required Keep the unit unplugged throughout installation except during testing e Never remove the round grounding prong from the plug and never use a two prong2. Initial Start Up Once installation and leveling is complete the unit is ready for initial start up and operation The ON OFF switch is located in the front grille see Figure 36 Temperature Control Knob ON OFF Switch Figure 36 1 Put the ON OFF switch in the ON position and set the Temperature Control Knob at 4 2 Assoon as the ice maker mold reaches the proper temperature the ice maker mechanism will fill the mold with water Note The first cubes may be small because of air in the water line Subsequent cubes will be standard size Figure 37 3 The ice maker will continue to produce until the bin is full You may interrupt production by raising the bin arm into an upright and locked position see Figure 37 While the bin arm is locked the unit will maintain temperature for ice storage IMPORTANT It is possible that dirt or scale will dislodge in the water line Always throw away all ice cubes made during the first twenty four 24 hours of operation About Settings No adjustments should be necessary at this time For information about Adjusting the Temperature Control and Adjusting Ice Cube Size see the User Manual www U LineService com D UsLINE BI2015 Ice Maker CORPORATION Start Up Troubleshooting Q Problem Unit does not appear to turn on when switch is set to ON A Z Solution Make sure unit is plugged
3. ne Wood Panel Bottom Hinge Plate 5 8 Longer than Existing Bottom Hinge Plate Pivot Post Figure 25 IMPORTANT Pivot posts must be cleaned Closers must also be clean and greased to ensure proper operation 5 Place the modified door onto the pivot post 6 Position door and install the pivot post into the top hinge using the 7 64 hex key or Phillips screwdriver 7 Adjust door as needed for proper closure Go on to 5 Adjust Door www U LineService com U U LINE CORPORATION 5 Adjust Door Checking Door Alignment The unit s door is aligned at the factory before shipment However its alignment could have been disturbed during shipment or during door panel installation IMPORTANT Properly aligned the door should be 1 8 below the top of the unit s cabinet NOT flush with the top see Figure 26 Figure 26 1 Compare the top edge of the door to the top edge of the cabinet 2 If the door edge is 1 8 below and parallel to the top of the cabinet go on to 6 Prepare Plumbing If it is not note whether the side opposite the hinge needs to be moved UP or DOWN and use the following procedure Note If door is adjusted correctly but panel is not square with the adjacent cabinets slight adjustments can be made by drilling the holes in the vinyl coated steel panel slightly oversized See Figure 21 on Page 10 Adjusting Door Alignment 1 Remove top hinge screw pin
4. 7 64 Allen wrench or Phillips screwdriver depending on your unit s construction see Figure 27 Remove door by tilting forward and lifting off bottom hinge pin 2 With door upside down loosen but do not remove the two screws on the door s bottom hinge plate Figure 27 www U LineService com 12 BI2015 Ice Maker Reinstall the closers lining Mountthe door install top Slotted Mounting Holes Raise lt _ gt _ Lower Outside Outside Door Edge Door Edge Figure 28 See Figure 28 If the top far edge of the door needs to move UP move the hinge plate toward the outside of the door and retighten screws If the top far edge of the door needs to move DOWN move the hinge plate toward the inside of the door and retighten screws Mount the door to recheck alignment and repeat Steps 2 and 3 if further adjustment is necessary When top edge of door is parallel to top edge of cabinet remove the door and ensure the two screws are secure Remove the door closers from the bottom hinge clean thoroughly and lubricate the mating surfaces with petroleum jelly up the bosses with holes in hinge and hinge plate see Figure 29 hinge pivot pin and go on to 6 Prepare Plumbing Figure 29 02 2005 BI2015 Ice Maker U U LINE CORPORATION 6 Prepare Plumbing CAUTION Plumbing installation must observe all stat
5. 3 4 Height 29 7 8 The door panel must not weigh more than 20 Ibs Relief Notch Rear View for Pivot Plate 0 Wood Panel Figure 15 IMPORTANT Rear View of wood panel for right hand hinge shown Use mirror image for left hand hinges 2 Create a relief Figure 15 for pivot plate by cutting notch in top corner and coinciding back corner of overlay panel Refer to Figure 16 for exact specifications 02 2005 BI2015 Ice Maker Y U INE CORPORATION 4 Drill hole for upper door hinge top of panel see 0 177 Dia 16 Drill Figure 16 Top View x 11 16 Deep 0 177 diameter 16 drill x 11 16 deep AE Door Bottom 5 Drill hole for lower door hinge see Figure 16 Bottom lt gt 5 16 Dia x 1 4 Deep View Chamfer 1 32 x 45 Top View Bottom View 5 16 diameter x 1 4 deep CAUTION It is important to ensure that all drilled holes are drilled to the correct depth in order to avoid splits in the wood when hardware is installed Haa Installation Instructions Removing Existing Door 1 Remove top hinge screw pin 7 64 hex key or Phillips screwdriver depending on your unit s construction Remove the door by tilting forward and lifting off the x 1 2 Deep fi aja bottom hinge pin 2 Pull door gasket out of the groove top edge of door Back View Side View only Start in the middle and pull outward moving F
6. bend the water supply line into position and connect the line to the solenoid valve see Figure 32 Avoid kinking the water supply line Figure 32 IMPORTANT Normal operation creates some vibration A water supply line contacting cabinet wall may cause excessive noise during operation or damage to the line 4 For recessed installations allow extra water supply line length to provide slack for easy removal from the recessed area see Figure 32 This will also safeguard against kinking the line 5 Goon to 7 Prepare Power Supply www U LineService com V U LINE CORPORATION 7 Prepare Power Supply Electrical Specifications CAUTION Electrical installation must observe all state and local codes This unit requires connection to a grounded three prong polarized receptacle that has been placed by a qualified electrician The unit requires a grounded and polarized 115 VAC 60 Hz 15A power supply normal household current An individual properly grounded branch circuit or circuit breaker is recommended GFCI ground fault circuit interrupter is usually not required for fixed location appliances and is not recommended for your unit because a GFCI could be prone to nuisance tripping However be sure to consult your local codes See Figure 33 for recommended receptacle location 23 11 16 Figure 33 A WARNING SHOCK HAZARD Electr
7. cabinet may be cleaned with a mild detergent and warm water solution Do not use solvent based or abrasive cleaners Use a soft sponge and rinse with clean water Wipe with a soft clean towel to prevent water spotting Stainless Steel Models e Stainless steel models can discolor when exposed to chlorine gas pool chemicals salt water or cleaners with bleach e Keep your stainless steel unit looking new by cleaning with a good quality all in one stainless steel cleaner polish on a monthly basis For best results use Claire Stainless Steel Polish and Cleaner which can be purchased from U Line Corporation The part number is 173348 Comparable products are acceptable Frequent cleaning will remove surface contamination that could lead to rust Some installations may require cleaning on a weekly basis Do not clean with steel wool pads Do not use cleaners that are not specifically intended for stainless steel this includes glass tile and counter cleaners e If any surface discolors or rusting appears clean it quickly with Bon Ami or Barkeepers Friend Cleanser and a non abrasive cloth Always clean in the direction of the grain Always finish this process with Claire Stainless Steel Polish and Cleaner or comparable product to prevent further problems e Use of abrasive pads such as Scotchbrite will cause the graining in the stainless to become blurred e Rust that is allowed to linger can penetrate into the surface
8. grounding adapter e Never use an extension cord to connect power to the unit e Always keep your working area dry CAUTION e Use care when moving and handling the unit Use gloves to prevent personal injury from sharp edges e Do not lift the unit by the door or door handle e Do not install the unit behind closed doors or in any way that would obstruct airflow to the front grille which may cause the unit to malfunction 02 2005 BI2015 Ice Maker U U LINE CORPORATION 2 lInspect and Plan You have received a carton containing your BI2015 Ice Maker with a package inside containing a User Manual a Product Registration Card and water connection parts Complete and mail the Product Registration Card or register online at www U LineService com Once your unit is installed keep the User Manual and this Installation Guide in a safe place for future reference Your unit is Black White or Stainless Steel Black and White units have a reversible door with a slightly contoured handle across the top They come with a flush mounted door panel that when removed will accept a custom 1 4 inch thick door panel or a 3 4 inch thick full overlay door panel Stainless Steel units are covered with a protective coating and have been ordered left or right hand hinged The Stainless doors are not reversible and do not accept custom panels Please carefully follow the directions that apply to your unit and your intended d
9. gt l lt A Between Appliances i Figure 11 02 2005 BI2015 Ice Maker U UFLINE CORPORATION 4 Prepare and Install Door Panel Black and White Units Only Two types of custom door panels can be installed on your Black or White unit to harmonize with or accent the surrounding d cor a Custom 1 4 Insert or a Full Overlay If no custom door panel is used go on to 5 Adjust Door Custom 1 4 Door Panel Insert Door Panel Preparation A custom door panel can be inserted into the doorframe Custom door panels can be flat or raised as long as the maximum panel thickness where inserted into the door reveal channel is 1 4 thick For raised panels the depth of the reveal is 1 4 on all four sides IMPORTANT Raised panels will reduce the door s 90 swing zero clearance if the unit is installed next to a wall or similar type of structure see Page 5 Cut the panel insert to the following dimensions Custom 1 4 Dimensions Width 14 1 32 Height 28 5 32 The door panel must not weigh more than 20 Ibs Door Panel Installation Install the insert as follows CAUTION Use care when handling the insert Insert edges may be sharp 1 Remove top hinge screw pin 7 64 Allen wrench or Phillips screwdriver depending on your unit s construction see Figure 12 Remove door by tilting forward and lifting off bottom hinge pin www U LineService com U U LINE CO
10. of the stainless steel and complete removal of the rust may not be possible 3 Prepare Site Your U Line product has been designed for either free standing or built in installation When built in your unit does not require additional air space for top sides or rear However the front grille must NOT be obstructed and clearance is required for water drain and electrical connections in the rear Note Unit can NOT be installed behind a closed cabinet door Cut Out Dimensions fe See Electrical Specifications for Power Supply 23 11 16 Figure 1 Follow the cut out drawing in Figure 1 The 15 3 16 width allows 1 4 for ease in installation and removal of the unit 24 is the counter depth in most installations The unit is 23 11 16 deep including the handle on Black and White models and 23 11 16 deep including the door and not the handle on Stainless Steel models see Figure 2 www U LineService com 02 2005 o TM amp Product Dimensions 25 13 16 Including Handle beeen je 23 11 16 Including i Er jew _ Le 14 1516 gt Stainless Steel Ea Et LL 14 15 16 Black and White Figure 2 Please note that the unit has adjustable feet that can add one additional inch to height during leveling or to match adjacent cabinets see Figure 35 on Page 14 Door Swing Clearances I
11. see Figure 7 www U LineService com U U LINE CORPORATION 4 Remove the two door closer inserts from the existing bottom hinge and install as shown on the new bottom hinge see Figure 8 Door Closer Inserts Figure 7 Figure 8 5 Remove existing bottom hinge 3 screws and remount on opposite side TOP Remove hinge screw pin 6 Remove the plastic hole plug from the top of the door to allow the pivot pin to be inserted in the new location Install the plug into the vacated hole on the opposite side 7 With bottom of door facing up remove pivot plate 2 screws flip over and remount on opposite side of door see Figure 9 Be sure notch in plate faces center Figure 9 8 Holding door upright with top of door tilted forward place hole of door pivot plate on bottom hinge screw pin see Figure 10 9 Tilt top of door into position in top hinge and install top hinge screw pin 10 Install plastic screw plugs removed in Step 2 in old hinge holes 3 each top and bottom Figure 10 www U LineService com BI2015 Ice Maker Other Site Requirements Power Supply The unit requires a grounded and polarized 115 VAC 60 Hz 15A circuit normal household current See Electrical Specifications on Page 14 Water Supply The unit requires a 1 4 inch OD water supply line and a shut off valve For more information see Page 13 Environmental Requirem
12. Pivot Plate 5 8 Longer Than Existing Bottom Pivot Plate Existing Bottom Pivot Plate Flush Side Facing Out Remove and Discard 8 32 x 3 8 SEMS Hex Screw Two Places Figure 23 IMPORTANT BI2015 Ice Maker Door panel and overlay panel must be aligned properly or the door will not operate correctly Assembling the Door 1 Install the assembled panel by sliding the original door panel back into the doorframe 2 Replace the two piece Modified Handle assembly and secure with the two screws removed in Step 5 under Removing Existing Door 3 Starting at the corners and working toward the center push the door gasket back into place Installing the Door 1 Remove the existing hinges from the unit saving the door closure assembly 2 Install the new Replacement Top Hinge onto the unit see Figure 24 02 2005 V U LINE CORPORATION Pivot roi Wood Panel Top Hinge Plate 5 8 Longer than Existing Top Hinge Plate we Co x 1 2 Flat Head Screw Three Places Door Panel Figure 24 3 Install the pivot post into the new Replacement Bottom Hinge using the 7 64 hex key or Phillips screwdriver and install the hinge onto the unit 4 Replace the door closure assembly onto the bottom pivot post see Figure 25 Be sure that bosses on closers align with holes in hinge and hinge plate Existing Door Closure Top Door Closure Bottom 8 32 X 1 2 Flat Head Screw Three Places
13. RPORATION Figure 12 Figure 13 2 Pull door gasket out of groove top edge of door only Start in the middle and pull outward moving toward the edge see Figure 13 This may take some force Do not remove the three screws behind gasket 3 Remove two outside screws holding door handle Slightly separate door handle from door see Figure 14 4 Pull handle up and off 5 Remove and discard existing panel and cardboard spacer 6 Slide custom door panel insert into 1 4 inch channel in door front 7 Holding door gasket out of the way replace handle Figure 14 on door making sure it is seated properly on insert and that screw holes line up 8 Install two small screws removed in Step 3 9 Starting at the corners and working inward push door gasket into place on door 10 Place door on bottom hinge pin and install upper hinge screw Go on to 5 Adjust Door www U LineService com BI2015 Ice Maker Full Overlay Door Panel Door Panel Preparation A full overlay door panel completely covers the doorframe and handle to give a built in appearance See your U Line dealer for the optional Full Overlay Door Panel Kit P N U OL2015B Black or P N U OL2015W White Appropriate hardware Modified Handle Replacement Hinges and a copy of these instructions will be included in the kit 1 Cut the overlay to the following dimensions see Figure 15 Full Overlay Dimensions Width 14
14. UW UFLINE CORPORATION Echelou Sertes Installation Guide EE BI2015 Ice Maker www U LineService com Phone 414 354 0300 FAX 414 354 7905 Service amp Parts Tech Lines Phone 800 779 2547 FAX 414 354 5696 OnlineService U Line com 2005 U Line Corporation 02 2005 U U LINE CORPORATION Contents Exterior Cleaning 4 Cut Out Dimensions 4 Product Dimensions 5 Door Swing Clearances Information 5 Reversing the Door 5 Other Site Requirements 6 Side By Side Installation Instructions 7 Custom 1 4 Door Panel Insert 7 Full Overlay Door Panel 8 Checking Door Alignment 12 Adjusting Door Alignment 12 Water Supply Connection 13 Electrical Specifications 14 Leveling Information 14 Installation Tip 14 Installation of the BI2015 15 Installation Troubleshooting 15 Initial Start Up 15 Start Up Troubleshooting 16 Service Information 17 www U LineService com BI2015 Ice Maker 1 Follow Safety Precautions
15. e and local codes All water connections MUST BE made by a licensed qualified plumbing contractor Failure to follow recommendations and instructions may result in damage and or harm N WARNING To prevent accidental electrocution make certain that the floor surfaces surrounding the unit are dry whenever power is removed from or applied to the unit Water Supply Connection When connecting the water supply follow these guidelines e Review the local plumbing codes before you install the unit e Connect to the cold water supply e The water pressure should be between 20 and 120 psi e Install a shut off valve in the 1 4 inch OD water supply line e Connect sufficient tubing to the unit so that tubing may be looped allowing the unit to be removed for cleaning and servicing see Figure 32 However make certain that the tubing is not pinched or damaged during installation e U Line recommends the use of copper tubing for installation To connect to water supply 1 Install the 1 4 inch OD copper water line from the main water source see Figure 30 Water Connection Figure 30 Figure 31 02 2005 2 Locate the compression fitting and ferrule packed with the unit Slide the compression fitting and ferrule over the 1 4 inch OD water supply line Do not use thread sealing compound or tape Using two wrenches tighten the compression fitting on the supply line see Figure 31 3 Carefully
16. ents The surrounding air temperature must be at least 50 F 10 C but must not exceed 110 F 40 C High ambient temperature ranges and warmer water supply will cause reduced ice production Black and White units may be installed outdoors in a covered area Stainless Steel BI2015 units are deemed suitable for outdoor use by UL The unit must not be located near heat generating equipment or in direct sunlight 02 2005 Side By Side Installation Instructions For a complete refreshment center install your BI2015 Ice Maker beside a U Line Refrigerator Combo or Wine Captain Model see Figure 11 for typical cut out Note that each Side By Side Installation will be different e Cut out width for a side by side installation is the total of the widths listed under Cut Out Dimensions in each unit s Installation Guide For example Placing a BI2015 Ice Maker next to a 2015 series unit would require a cut out width of 15 3 16 15 3 16 30 3 8 Placing a BI2015 Ice Maker next to a 2075 series unit would require a cut out width of 15 3 16 24 3 16 39 3 8 e No trim kit is required However 1 4 inch space needs to be maintained between the units to ensure unobstructed door swing e Units must operate from separate properly grounded electrical receptacles placed according to each unit s Electrical Specifications Typical Side By Side Cut Out 23 11 16 1 4 Space
17. esign Tools Materials Required e 7 64 Allen wrench e Screwdrivers slotted and Phillips head e 1 4 inch OD copper tubing and shut off valve for water supply line e 1 4 inch thick door panel material and cutting tools Black or White units e Full Overlay Door Panel Kit part number U OL2015B Black or part number U OL2015W White 3 4 inch door panel overlay cutting tools drill and bits Black or White units Inspection Unwrap and inspect the unit on a flat level surface capable of supporting its entire weight Removing Protective Coating Stainless Steel Units Only When inspecting installing a Stainless Steel unit the protective coating covering the unit must be removed first Start at a corner of the unit door and pull back the protective coating to remove it from the unit door www U LineService com V U LINE BI2015 Ice Maker TM CORPORATION After all the protective coating has been removed from the unit door clean all Stainless Steel surfaces with Claire Stainless Steel Polish and Cleaner or comparable product or a mild detergent and warm water solution and soft cloth Do NOT use abrasive cleaning agents Note If cleaning with mild detergent and warm water solution and soft cloth the unit MUST be treated with Claire Stainless Steel Polish and Cleaner or comparable product to prevent discoloration Exterior Cleaning As Required Black and White Models e The door grille and
18. ical Grounding Required e Never remove the round grounding prong from the plug and never use a two prong grounding adapter e Never use an extension cord to connect power to the unit Go on to 8 Level the Unit www U LineService com BI2015 Ice Maker 8 Level the Unit Leveling Information IMPORTANT It is extremely important that the unit is level If it is not level the ice mold will not fill evenly 1 Use a level to check the levelness of the ice maker from front to back and from side to side Level should be placed along top edge and side edge as shown see Figure 34 Figure 34 2 Ifthe ice maker is not level adjust the feet on the corners of the unit as necessary see Figure 35 0 We Tel Z Turn Foot to Adjust Figure 35 3 Check the levelness after each adjustment and repeat the previous steps until the unit is level Go on to 9 Install the Unit Installation Tip If the room floor is higher than the floor in the cut out opening adjust the rear feet to achieve a total unit rear height of 1 8 less than the opening s rear height Shorten the unit height in the front by adjusting the front feet This allows the unit to be gently tipped into the opening Readjust the front feet to level the unit after it is correctly positioned in the opening 02 2005 BI2015 Ice Maker V U LINE CORPORATION 9 Install
19. ied Handle to the lower handle using hardware to the overlay panel at this time the three screws removed in Step 3 Set aside 7 Slide the existing door panel out of the doorframe Attaching the Full Overlay Panel Hotel Door Panel 1 Tap nylon inserts into the top holes drilled in the overlay panel Use two 6 screws to attach top pivot bracket to the overlay panel see Figure 19 Typical Wood YP Banel id Al Sy RI Side of Wood Panel KB Wood Panel A 6 X 5 8 Flat Head Screw Two Required 3 8 Top Pivot i P Both Sides late 8mm Plug Insert Two Required Figure 20 Figure 19 Drill 5 32 x 3 8 Deep for use with 10 x 5 8 Wood Screw and Nylon Spacer 6 Places Rear View of Wood Panel 14 5 16 1 4 1 8 1 1 32 Figure 21 1 1 32 gt 4 Attach the door panel to the overlay panel using 10 x 5 8 wood screws and nylon spacers The nylon spacers fit between the overlay panel and the door panel as shown in Figure 22 The spacers allow the original door panel to slide back into the 1 4 thick door reveal channel www U LineService com 10 02 2005 Typical Door Panel Wood Panel Top ua a 10 x 5 8 Round Head Screw Six Required Plastic Spacer Six Required Figure 22 5 Remove the existing bottom pivot plate and replace with the Full Overlay pivot plate see Figure 23 Existing Door Wood Panel Bottom
20. igerators Wine Captain wine storage units refrigerators refrigerated drawers and refrigerator freezers 2005 U Line Corporation Publication No 30056E 02 2005 Rev A
21. igure 16 toward the edge see Figure 17 This may take some force Route notch in top corner of overlay panel as shown see Top and Side Views Top of notch is entire depth of panel front to back Width 13 16 Depth 1 8 Route notch in backside of top corner of overlay panel see Back and Side Views Width 13 16 Depth 1 8 Height 1 17 32 from top edge of panel less 1 8 for depth of notch on top of panel Radius of corner notch 1 8 see Back View Figure 17 Figure 18 3 Drill holes for pivot plate mounts see Figure 16 Back View 3 Remove the three screws located on the back of the 5 16 diameter x 1 2 deep from the routed surface handle see Figure 18 CAUTION Be careful not to drill too deep Drilling holes too deep may destroy your door panel 02 2005 9 www U LineService com V U LINE CORPORATION BI2015 Ice Maker 4 Remove the top handle and discard This handle will be 2 Place and tape the existing door panel on the back of replaced with the Modified Handle included in the Full the overlay panel see Figure 20 and drill holes Overlay Door Panel Kit through both panels according to Figure 21 Remove 5 Remove the two screws located on both sides of the Tepe Sa loining te KAME ADO En are ESEE lower handle Remove the handle the overlay panel using a 0 201 7 drill 3 If a user supplied cabinet handle will be used attach its 6 Attach the Modif
22. in and outlet has power circuit breaker has not tripped Remember that the ice maker mechanism will not fill the mold with water until the mold reaches the proper temperature Q Problem Water does not appear to be flowing into unit A Z Solution Check that the water is connected and turned on and the line is not obstructed Q Problem Ice cubes produced during the first two to three hours of operation have been discarded New cubes still appear cloudy A Solution This is normal and is caused by air being trapped in the cube during fast freezing IMPORTANT See the User Manual s Troubleshooting Guide for more solutions www U LineService com 16 02 2005 U U L LINE CORPORATION Who to Call Service Information If the need for service arises contact the dealer from whom the unit was purchased State the Model Number and Serial Number and explain the problem The Model and Serial Number plate is located inside unit at upper right hand corner If you need to locate a service company you can go online at www U LineService com and search for a service company by zip code For more than four decades U Line has distinguished itself as the leader in built in undercounter ice making refrigeration and wine storage appliances Echelon SERIES Ori gins SERIES U Line Corporation located in Milwaukee WI is a family operated manufacturer of built in undercounter icemakers Combo icemaker refr
23. nformation Black and White units have a zero clearance for the door to open 90 see Figure 3 Stainless Steel models require a minimum of 2 1 8 door clearance to accommodate the handle if the unit is installed next to a wall or similar type of structure Wall NMJ 2 1 8 Min gt j lt Pae Wall SM 1 4 Min lt 90 90 Door Swing Door Swing MA Black and White Figure 3 Stainless Steel 02 2005 BI2015 Ice Maker V U LINE CORPORATION Reversing the Door Black and White Units Only All U Line units except Stainless Steel models may be left or right hand opening The door opening is easily reversed by moving the hinge hardware to the opposite side The top hinge hardware will be used on the bottom of the other side and the bottom hinge hardware will be used on the top of the other side see Figure 4 To reverse the door 1 Remove top hinge screw pin from door 7 64 Allen wrench or Phillips screwdriver depending on your unit s construction see Figure 5 Remove door by tilting forward and lifting off bottom hinge pin Figure 4 2 Remove plastic screw plugs 3 each top and bottom from new hinge location Do not discard see Figure 6 Screw Plugs Figure 5 Figure 6 3 Remove top hinge 3 screws reinstall hinge screw pin and remount on opposite side BOTTOM
24. the Unit 10 Start Up for the First Time Installation of the BI2015 1 Open the water supply valve in the main water source 2 Make sure the ON OFF switch is in the OFF position see Figure 36 3 Plug in the power cord 4 Gently push the unit into position Be careful not to kink the water supply line or entangle the electrical cord 5 Re check the leveling from front to back and side to side Make any necessary adjustments The unit s top surface should be approximately 1 8 below the countertop Installation Troubleshooting Q Problem Water is leaking under the unit Z Solution A water leak under the unit is most likely caused by a bad connection in the water supply line Make sure the water line s brass fitting is screwed tight to its valve and threaded correctly Q Problem The door remains open unless it is pushed closed Z Solution The hinges should be self closing when the door is open approximately 8 If this is not the case make sure the closers at the bottom of the hinge pin are clean greased and installed correctly Also re check leveling from front to back of the unit and readjust if necessary Make sure that pivot plate is installed correctly Q Problem The custom overlay door was designed to align with the rest of the cabinet doors but the unit has crept forward A Solution Make sure that the electrical cord and water supply line are not obstructing the installation 02 2005
Download Pdf Manuals
Related Search