Home
Transition Networks CSRFB10XX-100 Network Card User Manual
Contents
1. Fiber LEDs OOO Link Activity Green ON Solid Link OFF no link E Green Blink Activity allo mi t Duplex FD Green ON Full Duplex s OFF Half Duplex 9 H Copper LEDs 3 On Link Activity Green ON Solid Link Blink Activity i LED2 Blink Rx Data eae Duplex LED2 Green ON Full Duplex Blink Activity Yellow ON Half Duplex Blink Activity a Speed LEDI Green 100 Mbps S LED 2 Yellow 10 Mbps S i LED EO 2 CSRFB Product Features Link Test button e Press the Link Test button to bypass TLPT when enabled e e Note This is a momentary override button when g released the connection will return to its previous g state ALI ga 2 CSRFB Link Test Button AutoCross The AutoCross feature detects and configures the twisted pair copper port on the CSRFB10xx 100 media converter to the correct straight through MDI or crossover MDI X configuration This feature allows either MDI or MDI X cable to connect the media converter to converters such as hubs transceivers or network interface cards NICs This feature does not require operator intervention techsupport transition com Click the Transition Now link for a live Web chat 7 CSRFBIOxx 100 Operation Continued Operation Continued Product features continued Product features continued Transparent link pass through TLPT TLPT notifies the end converter of a link failure by sending a link loss signal over
2. Maximum packet size 1916 bytes untagged bytes 1912 bytes tagged bytes Environment Tmra 0 to 50 C 32 to 122 F Storage Temp 25 to 65 C 13 to 149 F Humidity 5 to 95 non condensing Warranty Lifetime Manufacturer s rated ambient temperature Tmra range for this slide in module depends on the physical characteristics and the installation configuration of the Transition Networks PointSystem chassis in which this slide in module will be installed The information in this user s guide is subject to change For the most up to date information on the CSRFB10xx 100 media converter view the user s guide on line at www transition com Product is certified by the manufacturer to comply with DHHS Rule 21 CFR Subchapter J applicable at the date of manufacture CAUTION Visible and invisible laser radiation when open Do not stare into beam or view directly with optical instruments CAUTION Use of controls adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure The fiber optic transmitters on this converter meet Class I Laser safety requirements per IEC 825 CDRH standards and comply with 21 CFR1040 10 and 21CFR1040 11 12 24 hour Technical Support 1 200 260 1312 International 00 1 952 941 7600 Troubleshooting If the media converter fails isolate and correct the failure by determining the answers to the following questions and then
3. disconnect and reconnect the twisted pair cable to restart the initialization process e Contact Technical Support US Canada 1 800 260 1312 International 00 1 952 941 7600 techsupport transition com Click the Transition Now link for a live Web chat 13 CSRFBIOxx 100 Installation Continued 4 Is remote converter detected NO Check for proper connection from the terminal converter to center converter e Check the center terminal switch setting on both converters center converter switch set to center the terminal converter switch set to terminal e Contact Technical Support US Canada 1 800 260 1312 International 00 1 952 941 7600 YES Contact Technical Support US Canada 1 800 260 1312 International 00 1 952 941 7600 24 hour Technical Support 1 200 260 1312 International 00 1 952 941 7600 Contact Us Technical support Technical support is available 24 hours a day US and Canada 1 800 260 1312 International 00 1 952 941 7600 Transition now Chat live via the Web with Transition Networks Technical Support Log onto www transition com and click the Transition Now link Web Based seminars Transition Networks provides seminars via live web based training Log onto www transition com and click the Learning Center link E Mail Ask a question anytime by sending an e mail to our technical support staff techsupport transition com Address Transition Networ
4. taking the indicated action 1 Is the PWR power LED illuminated NO e Is the media converter inserted properly into the chassis e Is the power cord properly installed in the chassis and at the external power source and does the external power source provide power e Contact Technical Support US Canada 1 800 260 1312 International 00 1 952 941 7600 YES Proceed to step 2 2 Is the Link Activity twisted pair link LED illuminated NO e Check the copper cables for proper connection and pin assignment Contact Technical Support US Canada 1 800 260 1312 International 00 1 952 941 7600 YES Proceed to step 3 3 Is the LACT fiber pair link LED illuminated NO Check the fiber cables for proper connection e Verify that the TX and RX cables are connected to the RX and TX ports respectively on the 100Base FX converter e Contact Technical Support US Canada 1 800 260 1312 International 00 1 952 941 7600 YES Proceed to step 4 4 Is the Speed twisted pair speed LED illuminated NO e Check the copper cables for proper connection Off The media converter has selected 10Mbps operation e fthe speed is not correct disconnect and reconnect the twisted pair cable to restart the initialization process e Contact Technical Support US Canada 1 800 260 1312 International 00 1 952 941 7600 YES e On The media converter has selected 100Mbps operation e fthe speed is not correct
5. the fiber instructing the terminal converter to shut down the copper port thus notifying the end converter The fiber link between the two converters will be maintained End converter automatically notified of link loss Fiber link remains up as it carries the link loss signal Converter B Converter A receives link loss sends a link loss signal and disables signal over the the copper TX port fiber Far End Device Media Converter A Media Converter B i Near End Device End device is notified of link loss Converter A loses copper RX link with end device Far end fault When a fault occurs on an incoming fiber link 1 the media converter transmits a Far End Fault signal on the outgoing fiber link 2 In addition the Far End Fault signal also activates the Link Pass Through which in turn disables the link on the copper portion of the network 3 and 4 Original fault on fiber link Near End Media Media Far End Device Converter A Converter B Device Converter A Far end fault Converter B disables copper link signal sent disables copper link Auto Negotiation The Auto Negotiation feature allows the CSRFB10xx 100 media converter to automatically configure itself to achieve the best possible mode of operation over a link The media converter will broadcast its speed JOMbps or 100Mbps and duplex capabilities full or half to the other converters and negotiates the b
6. used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user s own expense Canadian regulations This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the radio interference regulations of the Canadian Department of Communications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la Class A prescrites dans le R glement sur le brouillage radio lectrique dict par le minist re des Communications du Canada European regulations Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Achtung Dieses ist ein Ger t der Funkst rgrenzwertklasse A In Wohnbereichen k nnen bei Betrieb dieses Ger tes Rundfunkst rungen auftreten In diesem Fall ist der Benutzer f r Gegenmafinahmen verantwortlich Attention Ceci est un produit de Classe A Dans un environment domestique ce produit risque de cr er des interf rences radio lectriques il appartiendra alors l utilsateur de prende les measures sp cifiques appropri es CAUTION RJ connectors are NOT INTENDED FOR CONNECTION TO THE PUBL
7. CSRFB 0xx 100 Installation CAUTION Wear a grounding converter and observe electrostatic discharge precautions while handling the media converter Failure to observe this caution could result in damage to or failure of the media converter Typical system configuration Fiber Cable 0O00 Chassis Center Converter Remote Terminal Converter SW6 set to Center SW6 set to Terminal Note The Loopback test occurs over the fiber connection The 6 position switch The 6 position switch is located on the side of the media converter r TP Auto Negotiate Up Enabled Down Disabled TP Duplex Up Full Down Half Use a small flat blade TP Speed Up 100Mbs Down 10Mbs screwdriver or a similar Fiber Duplex Up Full Down Half device to set the recessed TLPT Up Enabled Down Disabled switches Referto the drawing to the right for definitions of the individual switch positions Center Terminal Up C Down T 1 TP Auto Negotiation up Enables down Disables 2 TP Duplex Only valid if SW1 is Down up Full down Half 2 24 hour Technical Support 1 200 260 1312 International 00 1 952 941 7600 Installation Continued The 6 position switch continued 3 TP Speed Only valid if SW1 is Down up 100Mbps down 10Mbps 4 Fiber Duplex up Forces full duplex opera
8. EN TRANSITION User s Guide CSRFBI0xx 100 Slide in Module Media Converter e Copper to Fiber 10 100 Bridging 2 Port IOBase T IOOBase TX to l00Base FX The CSRFB10xx 100 2 port Ethernet Fast Ethernet bridging media converter is designed to be installed in a Transition Networks PointSystem chassis This converter connects 10Base T Ethernet or 100Base TX Fast Ethernet twisted pair copper network converters to network converters on a 100Base FX Fast Ethernet fiber network The CSRFB includes a status reporting feature for viewing operational parameters only from its remotely attached CSRFB converter via the fiber connection Part Number Port One Copper Port Two Duplex Fiber Optic 10Base T 100Base TX 100Base FX CSRFB1011 100 d p 1 E CSRFB1013 100 qp 328 0 US CSRFB1014 100 100 m 28 E m CSRFB1040 100 a 328 fi SFP Empty Slot CSRFB1029 100 100 m 28 ee CSREBIOAO Moom G28 20km 124 me CSRFB1029 102 100 m 328 fyt iis n A CSREB1028 103 100m 328 fi I R TT Install CSRFB1029 100 101 and CSRFB1029 102 103 single fiber optic in the same network where one is the local center converter and the other is the remote terminal converter Installation sssrin ssai ranirea 2 Operation eee ea tnos 7 Cable Specifications II Technical Specifications 12 Troubleshooting 13 ContactUs uuel erbe I5 Compliance Information l6
9. IC TELEPHONE NETWORK Failure to observe this caution could result in damage to the public telephone network Der Anschluss dieses Ger tes an ein ffentlickes Telekommunikationsnetz in den EG Mitgliedstaaten verst sst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91 263 EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten ber Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer Konformit t In accordance with European Union Directive 2002 96 EC of the European Parliament and of the Council of 27 January 2003 Transition Networks will accept post usage returns of this product for proper disposal The contact information for this mmm tivity can be found in the Contact Us portion of this document Trademark notice All trademarks and registered trademarks are the property of their respective owners Copyright restrictions 2005 Transition Networks All rights reserved No part of this work may be reproduced or used in any form or by any means graphic electronic or mechanical without written permission from Transition Networks l6 Printed in the U S A 33410 A
10. To install the CSRFB10xx 100 media converter slide in module AutoCross jumper 1 Locate an empty installation slot on the PointSystem chassis The AutoCross jumper is located on the media converter s circuit board labeled NA 2 Carefully slide the module into the slot aligning the module with the No Autocross A AutoCross See Jumper position below installation guides Note Use small needle nose pliers to set the 3 Ensure that the module is firmly seated inside the chassis jumper f A p h ieht th h 9g 4 Push in and rotate the panel fastener screw to secure the module to the chassis ither straight through or crossover fi A O NA ront cable can be used for all twisted pair 0 0 copper links Pm 1 2 3 Panel Fastener Mounting Hol NA Straight through or crossover twisted Allo Em NA RUE pair cable depending on installed site ZZ e converters MUST be installed at EACH AutoCross C p ENS ON twisted pair copper link E Note Factory default is A enabled Transition Networks recommends leaving ae RN tik it i the converter in the A enabled position Rr et lo Chassis d The Loopback Mode jumper is located on the media J4 converter s circuit board labeled ALL all frames All o ol Good plus errors Good Good frames only See Jumper ci A position to the right Media Converter A
11. Transmitter Power min 8 0 dBm max 3 0 dBm Fiber optic Receiver Sensitivity min 33 0 dBm max 3 0 dBm Link Budget 25 0 dB Copper cable maximum cable distance 100 meters Category 3 Minimum requirement for 10 Mbps operation Gauge 24 to 22 AWG Attenuation 11 5 dB 100m 5 10 MHz Category 5 Minimum requirement for 100 Mbps operation Gauge 24 to 22 AWG Attenuation 22 0 dB 100m 100 MHz Straight through MDI or crossover MDI X twisted pair cable must be used Shielded twisted pair STP or unshielded twisted pair UTP may be used Pins 1 amp 2 and 3 amp 6 are the two active pairs in an Ethernet network Use only dedicated wire pairs for the active pins e g blue white amp white blue orange white amp white orange etc Do not use flat or silver satin wire Straight Through Cable Crossover Cable Twisted Pair 1 Twisted Pair 1 Twisted Pair 2 Twisted Pair 2 24 hour Technical Support 1 200 260 1312 International 00 1 952 941 7600 techsupport transition com Click the Transition Now link for a live Web chat CSRFBIOxx 100 Technical Specifications For use with Transition Networks Model CSRFB10xx 100 or equivalent Standards IEEE 802 3 7M Data Rate 10 Mbps 100 Mbps Dimensions 3 4 x 5 x 1 86 mm x 127 mm x 25 4 mm Weight 4 oz 114 g approximate Power Consumption 3 0W MTBF 280 232 MIL HDBK 217F Hours 770 637 Bellcore Hours Packet Size Unicast MAC address 1K
12. est mode of operation Auto Negotiation allows quick and easy installation because the optimal link is established automatically No user intervention is required to determine the best mode of operation A scenario where the media converter is linked to a non negotiating converter is a case where the user may want to disable Auto Negotiation In this instance the mode of operation will drop to the least common denominator between the two converters e g 100 Mbps half duplex Disabling this feature gives the user the ability to force the connection to the best mode of operation 24 hour Technical Support 1 200 260 1312 International 00 1 952 941 7600 Parallel detection Per the IEEE method an auto negotiating port that detects a forced link partner should drop to the detected speed 10Mbps or 100Mbps and default to HALF DUPLEX Full duplex network In a full duplex network maximum cable lengths are determined by the type of cables that are used See page 1 front cover for the cable specifications for the different CSRFB10xx 100 models Half duplex network 512 Bit Rule In a half duplex network the maximum cable lengths are determined by the round trip delay limitations of each Fast Ethernet collision domain A collision domain is the longest path between any two terminal converters e g a terminal switch or router The 512 Bit Rule determines the maximum length of cable permitted by calculating the round trip dela
13. he cable to the RJ 45 port connector on the other converter switch workstation etc Note The MDI straight through or MDI X crossover cable connection is configured automatically when the AutoCross jumper is in the enabled position Point System Chassis RJ 45 Port Media Converter RJ 45 Port On other device workstation switch etc Install the fiber cable 1 Locate or build IEEE 803 2 compliant 100Base FX fiber cable with male two stranded TX to RX connectors installed at both ends 2 Connect the fiber cables to the CSRFB10xx 100 media converter as described Connect the male TX cable connector to the female TX connector Connect the male RX cable connector to the female RX connector 3 Connect the fiber cables to the other converter media converter hub etc as described Connect the male TX cable connector to the female RX connector Connect the male RX cable connector to the female TX connector Connect fiber cable Connect fiber cable to media converter to other device as shown media converter hub etc as shown ee RX TX 6 24 hour Technical Support 1 200 260 1312 International 00 1 952 94 7600 Operation Status LEDs LED Description a Ux i J Power ON Power N OFF No power E So
14. ks 10900 Red Circle Drive Minnetonka MN 55343 U S A telephone 952 941 7600 toll free 800 526 9267 fax 952 941 2322 TRANSITION Declaration of Conformity a NETWORKS Name of Mfg Transition Networks 10900 Red Circle Drive Minnetonka MN 55343 U S A Model CSRFB10xx 100 Series Media Converters Part Number s CSRFB1011 100 CSRFB1013 100 CSRFB1014 100 CSRFB1029 100 CSRFB1029 10 CSRFB1029 102 CSRFB1029 103 CSRFB1040 100 Regulation EMC Directive 89 336 EEC Purpose To declare that the CSRFB10xx 100 to which this declaration refers is in conformity with the following standards EMC CISPR 22 1985 Class A EN 55022 1998 Class A FCC Part 15 subpart B 22 CFR subpart J I the undersigned hereby declare that the equipment specified above conforms to the above Directive s and Standard s Asap Sn PPP April 2009 Stephen Anderson Vice President of Engineering Date techsupport transition com Click the Transition Now link for a live Web chat Compliance Information CISPR22 EN55022 Class A EN55024 CE Mark FCC regulations This equipment has been tested and found to comply with the limits for a Class A digital converter pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and
15. l bandwidth This feature is controlled by a Point System management module installed in a Point System Chassis along with the SW6 position of the CSRFB converter set to Cable Specifications The physical characteristics must meet or exceed IEEE 802 3 specifications Fiber cable Bit Error Rate 10 9 Single mode fiber recommended 9 um Multimode fiber recommended 62 5 125 um Multimode fiber optional center The following rates are available for all traffic 64 Kbps 128 Kbps 256 Kbps 512 Kbps 1 Mbps 2 Mbps 4 Mbps 8 Mbps 16 Mbps 32 Mbps 64 Mbps 72 Mbps 80 Mbps 88 Mbps No Limit 100 140 85 140 50 125 um CSRFB1011 100 multimode Fiber Optic Transmitter Power min 19 0 dBm max 14 0 dBm Fiber Optic Receiver Sensitivity min 30 0 dBm max 14 0 dBm Link Budget 11 0 dB CSRFB1013 100 multimode Fiber Optic Transmitter Power min 19 0 dBm max 14 0 dBm Fiber Optic Receiver Sensitivity min 30 0 dBm max 14 0 dBm Link Budget 11 0 dB CSRFB1014 100 single mode Fiber optic Transmitter Power min 15 0 dBm max 8 0 dBm Fiber optic Receiver Sensitivity min 31 0 dBm max 8 0 dBm Link Budget 16 0 dB CSRFB1029 100 1310TX 1550 CSRFB1029 101 1550TX 1310 single mode Fiber optic Transmitter Power min 14 0 dBm max 8 0 dBm Fiber optic Receiver Sensitivity min 33 0 dBm max 3 0 dBm Link Budget 19 0 dB CSRFB1029 102 1310TX 1550 CSRFB1029 103 1550TX 1310 single mode Fiber optic
16. ll EMI c Frames Loopback test The loopback test is an automatic test run from the center chassis converter with SW6 set to center the UP position of the switch and on the terminal converter with SW6 set to terminal the DOWN position of the switch Note This test is self running after being initiated through software on the center converter The Loopback test does the following 1 The center converter will put the terminal converter in loopback mode 2 The center converter sends 100 packets to the terminal converter 3 The center converter will monitor its receiver for a good packets b CRC errors c timeouts 4 After the center converter receives all 100 packets back or a time out occurs it will update its counters and return the terminal converter to its previous mode of operation After completing the test normal operation of the center and terminal converters is established automatically 4 24 hour Technical Support 1 200 260 1312 International 00 1 952 941 7600 techsupport transition com Click the Transition Now link for a live Web chat CSRFBIOxx 100 Installation Continued Install the twisted pair copper cable 1 Locate IEEE 803 2 compliant 10Base T or 100Base TX cable with RJ 45 connectors installed on both ends 2 Connect the RJ 45 connector at one end of the cable to the RJ 45 port connector on the media converter 3 Connect the RJ 45 connector at the other end of t
17. tion on the fiber port down Forces half duplex operation on the fiber port 5 Transparent Link Pass Through TLPT up Enabled down Disabled 6 Center Terminal Mode see note up Center mode center converter only down Terminal mode terminal converter only Note To use the TS1000 compliant Center Terminal mode function set SW6 on the center converter in the chassis to Center Mode the UP position on the terminal converter at the remote location set SW6 to Terminal Mode the DOWN position This allows you to view parameters of the terminal converter from the center converter for monitoring purposes only Hardware software mode jumper The jumpers are located on the media converter circuit board Use small needle nosed pliers or a similar converter to set the jumper The Hardware Software jumper is labeled H for hardware and S for software J Hardware The media converter mode is determined H o ol Oo by the settings on the 6 position switch pins 2 3 Software The media converter mode is determined Ho o o by the most recently saved on board S microprocessor settings Hardware Software Note Software Mode only when the SW6 of the chassis converter is in the UP position center techsupport transition com Click the Transition Now link for a live Web chat CSRFBIOxx 100 Installation Continued Install the slide in module
18. y in bit times BT of a particular collision domain If the result is less than or equal to 512 BT the path is good For more information on the 512 Bit Rule see the white paper titled Collision Domains on line at www transition com SNMP See the on line documentation that comes with Transition Networks FocalPoint software for applicable commands and usage Use SNMP at an attached terminal or at a remote location to monitor the media converter by monitoring e Media converter power e Serial and part number Port number e Copper and fiber link status Copper and fiber duplex mode Copper port speed e Hardware switch setting e View terminal converter status e Set port ingress rate limits of the center side converter Also use SNMP to enter network commands that do the following Enable disable Auto Negotiation on copper e Force 10Mbps or 100Mbps on copper Force full duplex or half duplex on copper Force full duplex or half duplex on fiber Enable disable Transparent Link Pass Through techsupport transition com Click the Transition Now link for a live Web chat 9 CSRFBIOxx 100 Operation Continued Product features continued Bandwidth allocation Bandwidth allocation feature is available on the Center located SRFB converter only The center converter supports independent ingress rate limiting on both the copper and fiber ports The increments range from 64kps up to ful
Download Pdf Manuals
Related Search
Related Contents
Ariete 638 ice cream maker PL_F 800 GT 03-14-span.indd Manual - Potter Electric Signal Company, LLC Installation & User Guide MIra Coda THErMoSTaTIC Copyright © All rights reserved.
Failed to retrieve file