Transition Networks CPSMC0800
Contents
1. CPSMM 200 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 22 JUISU Y4OM U CPSMC08xx 100 PointSystem Chassis DB 9 Serial Port The DB 9 serial port allows the network administrator to configure and manage the CPSMC08xx 100 chassis using the SNMP Command Line Interface CLI at an attached terminal or terminal emulator Use a null modem cable to attach a terminal to the DB 9 serial port on the management module as shown Attached terminal or terminal emulator LO EEE ool to the DB 9 serial port 4 E A null modem cable om aa 0 0000 le oo F RJ 45 Ethernet Port The RJ 45 Ethernet port allows the network administrator to manage the CPSMCO8xx 100 chassis via a remote Network Management Station NMS in one of two ways 1 Using the Transition Networks FocalPoint graphical user interface 2 Using a remote Telnet connection Use an RJ 45 network cable to attach a terminal via a network hub or switch to the RJ 45 Ethernet port on the management module as shown r Network hub or switch connected Remote Telnet connection OR to the RJ 45 Ethernet port Remote NMS with an SNMP application NOTE To manage the PointSystem chassis via a remote NMS both the RJ 45 Ethernet port and the NMS must be connected to a network with Internet acce2. modules The chassis allows the network administrator to connect various copper and fiber optic network media over protocols that include Ethernet Fast Ethernet DS3 E3 and OC 12 The chassis provides installation space for up to eight 8 single slot or four 4 dual slot media converter slide in modules in the front of the unit uononpo jul Management Module Installed Slide In Module Open Slot Power Inlet Fa e vocole oo Mle e ii bh le 0 0009 le 00 I The CPSMC0800 100 comes equipped with an AC power supply The CPSMC0810 100 comes equipped with a DC power supply An optional auxiliary AC or DC power supply with instant fail over operation is also available for either model The primary power supply is accessed through the power inlet on the front panel while auxiliary power is accessed through the auxiliary power inlet located on the back panel Grounding Lugs Auxiliary Power Inlet t C lt 7 The CPSMCO8xx 100 also comes equipped with a pair of grounding lugs for providing proper grounding of the chassis Multiple fans help remove heat from the chassis With installed PointSystem management module s P N CPSMM 120 200 or 210 the CPSMCO8xx 100 can be managed and monitored via e An SNMP application such as Transition Networks Foca Point management software installed at a remote Network Management Station NMS e A remote Web browser e A command line interf
3. CPSMCO8xx 100 chassis is 40 C If the chassis is installed in a closed or multi unit rack assembly the operating ambient temperature of the the rack environment may be greater than room ambient NOTE Rack mounted equipment must be reliably grounded Power supply connections other than direct connection to the branch circuit e g use of power strips should be employed Flush Alignment T ess ligament OO O naaia f at front at front i at back at back Flush Alignment al Recessed Alignment The CPSMCO8xx 100 chassis is designed so that the installation brackets can be installed to align the chassis either flush against the front or back edge of the rack or recessed from the front or back edge of the rack WARNING Select mounting bracket locations on the chassis that will keep the chassis balanced when mounted in the rack Failure to observe this warning could allow the chassis to fall resulting in equipment damage and or possible injury to personnel 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 16 yo SISSV CPSMC08xx 100 PointSystem Chassis To install the CPSMCO8xx 100 chassis into a standard 19 inch rack 1 Determine the preferred alignment of the chassis in the rack NOTE Installation bracket mounting screws are provided Rack mount screws and clip nuts are NOT provided Locate six 6 installation bracket mounting screws provided for each chassis to
4. as No Problem Found THIS WARRANTY IS YOUR ONLY REMEDY NO OTHER WARRANTIES SUCH AS FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSED OR IMPLIED TRANSITION NETWORKS IS NOT LIABLE FOR ANY SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES INCLUDING LOSS OF DATA ARISING FROM ANY CAUSE OR THEORY AUTHORIZED RESELLERS ARE NOT AUTHORIZED TO EXTEND ANY DIFFERENT WARRANTY ON TRANSITION NETWORKS BEHALF 30
5. le minist re des Communications du Canada European Regulations Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Achtung Dieses ist ein Ger t der Funkst rgrenzwertklasse A In Wohnbereichen k nnen bei Betrieb dieses Ger tes Rundfunkst rungen auftreten In diesem Fall ist der Benutzer ftir Gegenma nahmen verantwortlich Attention Ceci est un produit de Classe A Dans un environment domestique ce produit risque de cr er des interf rences radio lectriques il appartiendra alors a utilsateur de prende les measures sp cifiques appropri es CAUTION THE RJ CONNECTORS ON THE INDIVIDUAL MEDIA CONVERTER SLIDE IN MODULES ARE NOT INTENDED FOR CONNECTION TO THE PUBLIC TELEPHONE NETWORK Failure to observe this caution could result in damage to the public telephone network Der Anschluss dieses Ger tes an ein 6ffentlickes Telekommunikationsnetz in den EG Mitgliedstaaten verst sst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91 263 EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten ber Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer Konformitat Trademark Notice All trademarks and registered trademarks are the property of their respective owners Copyright Restrictions 2003 2004 Transition Networks All rights reserved No
6. not included with the chassis and must be provided by the customer installer The electrical conducting path from the chassis must e Flow via the grounding lugs to the Common Bonding Network CBN for telecom installations or to an alternate approved grounding system if required for non telecom installations e Be of sufficiently low impedance to conduct fault currents likely to be imposed on the chassis and e Enable proper operation of any over current protection devices The two hole compression type grounding connector must be fastened to the grounding lugs with the enclosed anti rotation star washers and lug nut fasteners The required torque to the fasteners is specified by the connector s manufacturer Grounding lugs 6 32 1 8 diam Pa i Two hole compression type 3 4 inch Al grounding connector not included i G Star washer included Lig zu OY Ol 12 AWG copper wire wie eC not included J oO Basa Os e To properly ground the CPSMCO8xx 100 chassis 1 Obtain one 1 properly terminated grounding conductor 12 AWG copper wire gauge or larger with a two hole compression type grounding connector Note the manufacturer s applied torque that is required for the connector Lug nuts included yo Sisse 2 Attach the grounding conductor to the chassis by placing the two hole compression type connector onto the grounding lugs and fasten with appropriate lock washers and lu
7. result in diminishing system reliability In other words the combined wattage of the CPSMCO8xx 100 chassis plus all slide in modules must be less than the available power Contact Transition Networks Tech Support to ensure the power requirements for your specific application do not exceed the available power sa npouu ur 3p s CPSMC08xx 100 PointSystem Chassis 2 1 3 Installing the Media Converter Slide in Modules CAUTION Wear a grounding device and observe electrostatic discharge precautions when installing the media converter slide in module s into the chassis Failure to observe this caution could result in damage to and subsequent failure of the media converter slide in module s NOTE The media converter slide in modules can be installed in any installation slot in any order To install the media converter slide in module into the CPSMCO8xx 100 chassis 1 Remove the protective plate from the installation slot by removing the one 1 screw that secures the plate to the front of the chassis NOTE If the slide in module requires two slots remove the protective plates from two 2 adjacent installation slots 2 Align the slide in module with the chassis installation slot so that the panel fastener screw is at the left of the slide in module soch 100 e o T OO ad e 0000 Panel Fastener Screw 3 Carefully slide the slide in module into the installation slot while alig
8. the active pins e g blue white amp white blue orange white amp white orange etc e Do not use flat or silver satin wire 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 26 CPSMC08xx 100 PointSystem Chassis COAX Cable Coaxial cable media is used for circuits such as DS3 E1 and 10Base 2 Ethernet The impedance of the coaxial cable is determined by the interface type for example e 75 ohm for DS3 e 50 ohm for 10Base 2 Ethernet Special attention should be given to the grounding requirements of coaxial cable circuits Installation may require grounding at both cable ends or only one cable end or neither cable end Cable Shield Grounding Media converter network cabling my be shielded or unshielded Shielded cables MUST be grounded according to the specific requirements of the media and port type For example e Shielded RJ 45 cable used for 100Base Tx Ethernet MUST be grounded at both cable endpoints via shielded RJ 45 jacks e Shielded RS 232 cable MUST have the shield grounded at both cable endpoints via shielded RS 232 connectors e COAX cable used for 10Base 2 Ethernet MUST only be grounded at a single point The media converters provide a jumper option or other grounding mechanism as required Special attention should be given to the grounding requirements of coaxial cable circuits Installation may require grounding at both cable ends or only one cable end or neither cable en
9. the back of the chassis Connect the 48 VDC terminal to the connector marked Turn the terminal screw clockwise to secure Connect the 48 VDC terminal to the connector marked Turn the terminal screw clockwise to secure Connect the ground terminal to the connector marked chassis ground Turn the terminal screw clockwise to secure Verify that Auxiliary power supply is connected properly by disconnecting the primary power supply and then by observing the illuminated power LEDs on the installed slide in modules and by the chassis fan operation Auxiliary Power Inlet External Power Converter Ajddns amod CPSMC08xx 100 PointSystem Chassis 4 CPSMC08xx 100 Chassis 4 1 Installing the CPSMCO8xx 100 Chassis The CPSMCO8xx 100 can be installed in a standard 19 inch rack or on a table shelf or other stable surface CAUTION Install the chassis so that the air flow around it is not restricted 4 1 1 Table Top Installation The CPSMCO8xx 100 chassis is shipped with nine 9 rubber feet for optional installation on a table or other flat stable surface in a well ventilated area If table top installation is desired remove the rubber feet from the card and place them on the bottom of the chassis Distribute the feet so that the chassis is level when placed upright 4 1 2 Standard 19 inch Rack Installation The maximum recommended ambient temperature Tmra for the
10. two adjacent slots in the NI VEZAN 6 aa CPSMCO8xx 100 chassis for installation N Refer to the CPSMM 200 210 user s guide for more information on the CPSMM 200 Dual Slot Master Management Module CPSMM 210 Single Slot Expansion Management Module The CPSMM 210 is used with the CPSMM 200 to connect up to eight 8 PointSystem chassis into one manageable stack Refer to the CPSMM 200 210 user s guide for more information on the CPSMM 210 Single Slot Expansion Management Module See section 4 3 Cascade Option for details on connecting multiple CPSMCO8xx 100 chassis 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 CPSMM210 sa npouu ur 3p s CPSMC08xx 100 PointSystem Chassis 2 2 2 Installing the Management Modules CAUTION Wear a grounding device and observe electrostatic discharge precautions when installing the management module s in the CPSMCO8xx 100 chassis Failure to observe this caution could result in damage to and subsequent failure of the management module NOTE Transition Networks recommends installing the management module into the left most installation slots to keep the management cables separate from the media converter cables To install a management module into the CPSMCO8xx 100 chassis 1a CPSMM 200 Dual Slot Master Management Module If chassis face plates are covering the installation slots remove two 2 management
11. Another CPSMM 200 managment module is installed in the next chassis as a backup In this set up the two CPSMM 200 management modules auto negotiate so that one module is in stand by mode If the primary management module fails the stand by module automatically takes over and manages the network 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 19 CPSMC08xx 100 PointSystem Chassis To cascade two or more CPSMCO8xx 100 chassis 1 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 20 Locate one 1 Transition Networks management module cascade cable with RJ 45 connectors installed at both ends P N 6026 for each set of two 2 chassis to be cascaded NOTE Transition Networks management module cascade cables are one 1 meter long Ensure that the chassis are installed within one 1 meter of each other At the first chassis in the series Plug the RJ 45 connector at one end of the cascade cable into the management module s RJ 45 port labeled OUT At the next chassis in the series Plug the RJ 45 connector at the other end of the cascade cable into the management module s RJ 45 port labeled IN At the same chassis as in step 3 Plug the RJ 45 connector at one end of the cascade cable into the management module s RJ 45 port labeled OUT At the next chassis in the series Plug the RJ 45 connector at the other end of the cascade c
12. CRA RMA Failure to properly protect the product during shipping may void this warranty The return authorization number must be written on the outside of the carton to ensure its acceptance We cannot accept delivery of any equipment that is sent to us without a CRA or RMA number The customer must pay for the non compliant product s return transportation costs to Transition Networks for evaluation of said product s for repair or replacement Transition Networks will pay for the shipping of the repaired or replaced in warranty product s back to the customer any and all customs charges tariffs or and taxes are the customer s responsibility 29 CPSMC08xx 100 PointSystem Chassis Before making any non warranty repair Transition Networks requires a 200 00 charge plus actual shipping costs to and from the customer If the repair is greater than 200 00 an estimate is issued to the customer for authorization of repair If no authorization is obtained or the product is deemed not repairable Transition Networks will retain the 200 00 service charge and return the product to the customer not repaired Non warranted products that are repaired by Transition Networks for a fee will carry a 180 day limited warranty All warranty claims are subject to the restrictions and conventions set forth by this document Transition Networks reserves the right to charge for all testing and shipping incurred if after testing a return is classified
13. G 13 3 2 Auxiliary Power Supply lt lt 2 04 aude 8a eee ane Rha ease 14 3 2 1 AC Auxiliary Power Supply ce 14 3 2 2 DC Auxiliary Power Supply 20 0 0 00 cee ee eee 15 4 CPSMCO08xx 100 Chassis 2c cee eee eee eee ee 16 4 1 Installing the CPSMCO8xx 100 Chassis 0 16 4 1 1 Table Top Installation 0 2 0 eee 16 4 1 2 Standard 19 Inch Rack Installation 0 0 0 0000 16 Als Grounding LUGS lt r ico atit baie voc at aciie Nowe wy thie a S 18 42 Cascade CODE OM ze ep pales eco spade ee ed acd OR RE RT ENS 19 4 3 Connecting the Slide in Modules to the Network 21 AA MODE AVON rea a A Ait date ete a EAER Ales esa 21 5 Network Management 0 2 e ee eee e eee eeee 22 5 1 Hardware Connections 2 4ca n ene s yang eh ala eRe LS 22 6 Troubleshooting 0 060 ccc cee eee meme ee eens 24 Technical Specifications v4 cca Dre st net a este za e ate de tear prow i d 25 Cable Specifications ap se neat aa wae aes a cu E Ra ee a A 26 Contact US haamana Ate 8 OS Cae Acad ia 0 EER pna eae 28 Warranty osetia ch tort sites hr 0 nate aan alt ene a a Pa ala Sra 29 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 3 CPSMC08xx 100 PointSystem Chassis 1 Introduction 1 1 Description The Transition Networks PointSystem CPSMCO8xx 100 is a 19 inch rack mountable chassis for selected Transition Networks media converter slide in
14. TRANSITION networks Transition Networks CPSMC08xx 100 8 Slot PointSystem Chassis User s Guide revision B ME IL x Tiga ae o E 1 II Cn fosa ni II CPSMC0800 100 AC powered CPSMC08 10 100 DC powered CPSMC08xx 100 PointSystem Chassis Compliance Information CISPR22 EN55022 Class A EN55024 CE Mark FCC Regulations This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user s own expense Canadian Regulations This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the radio interference regulations of the Canadian Department of Communications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la Class A prescrites dans le Reglement sur le brouillage radio lectrique dict par
15. able into the management module s RJ 45 port labeled IN Repeat steps 4 and 5 until all chassis have been connected yo Sisse CPSMC08xx 100 PointSystem Chassis 4 3 Connecting the Slide in Modules to the Network Once the CPSMCO8xx 100 chassis has been installed the media converter slide in modules may be connected to the network CAUTION Connect input output network cables ONLY to media converter slide in module connectors within the same network protocol such as Ethernet to Ethernet Fast Ethernet to Fast Ethernet ATM to ATM Failure to observe this caution will cause data transfer to fail Refer to the user s guides included with the media converter slide in modules for cabling specifications and instructions Check the individual user s guides for specific information on how to connect each slide in module to the network OULUI Daily operation of the CPSMCO8xx 100 chassis requires no network administrator activity except for the occasional monitoring of the status LED indicators on the installed media converter slide in modules 4 4 Operation Each media converter slide in module and each management module has one or more LED indicators to help monitor the network Refer to the user s guide included with each management module and slide in module to interpret the LED indicators on the modules LED indicators on the management module and slide in mo
16. above conforms to the above Directive s and Standard s Aspe a Oe April 1 2003 Stephen Anderson Vice President of Engineering Date 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 25 CPSMC08xx 100 PointSystem Chassis Cable Specifications Null Modem Cable The Null Modem Cable is used for connecting a terminal or terminal emulator to the management module s DB 9 connector to access the command line interface The table below shows the pin assignments for the DB9 cable Function Mnemonic Pin Carrier Detect CD 1 Receive Data RXD 2 Transmit Data TXD 3 Data Terminal Ready DTR 4 Signal Ground GND 5 Data Set Ready DSR 6 Request To Send RTS 7 Clear To Send CTS 8 25 Pin RS 232 Hull Modem Cable Chassis Ground 1 1 Chassis Ground Transmit Data 2 3 Receive Data Receive Data 3 2 Transmit Data Request To Send 4 7 4 Request To Send Clear To Send 5 5 Clear Ta Send Data Set Ready 6 20 Data Terminal Ready Carrier Detect 6 E E 6 Data Set Ready Data Terminal Ready 20 Carrier Detect Signal Ground 7 7 Signal Ground RJ 45 Cable Category 5 Gauge 24 to 22 AWG Attenuation 22 0 dB 100m e 100 MHz Maximum Cable Distance 100 meters e Straight through OR crossover cable may be used e Shielded twisted pair STP OR unshielded twisted pair UTP may be used e All pin pairs 1 amp 2 3 amp 6 4 amp 5 7 amp 8 are active in a Gigabit Ethernet network e Use only dedicated wire pairs for
17. ace CLI at an attached terminal e Acommand line interface CLI at a remote Telnet connection The management modules also make it possible to control up to eight 8 cascaded chassis fully populated with installed media converter slide in modules 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 4 CPSMC08xx 100 PointSystem Chassis 1 2 Unpacking the CPSMC08xx 100 Equipment Use the following list to verify the shipment Item 8 Slot chassis with AC power supply 8 Slot chassis with DC power supply PointSystem chassis face plates 5 Power Cord FocalPoint Software Disk included with the management modules User s Guide Part Number CPSMC0800 100 CPSMC0810 100 CPSFP 200 uononponui varies by country Al 7227 33270 The following items are optional accessories for the CPSMCO8xx 100 8 slot PointSystem chassis Item External AC Power Supply External DC Power Supply 1 slot Master Management Module 2 slot Master Management Module Expansion Management Module Management Module Cascade Connector 23 inch Rack Mount Ears Selectable Media Converter Slide in Module s Part Number CPSMP 180 optional CPSMP 190 optional CPSMM 100 optional CPSMM 200 optional CPSMM 210 optional 6026 optional CPSRE 238 optional various P N optional 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 5 CPSMC08xx 100 PointSystem C
18. assis can also be supplied with auxiliary power from an external power converter which is connected to the chassis through the auxiliary power inlet located on the back panel Both and AC and a DC external power converter are available from Transition Networks Instant Fail Over Protection The CPSMCO8xx 100 has instant fail over protection when both the primary and auxiliary power supplies are connected to external power sources The auxiliary power supply waits in stand by ready to supply power to the chassis in the event of power failure from the primary power supply AC and DC Power Supplies The CPSMC0800 100 with the internal AC power supply can have either the AC powered CPSMP 180 or the DC powered CPSMP 190 as the Auxiliary power supply Likewise the CPSMC0810 100 with the internal DC power supply can have either the AC powered CPSMP 180 or the DC powered CPSMP 190 as the Auxiliary power supply AC Auxiliary Power Supply To power the CPSMCO8xx 100 chassis through the AC auxiliary power supply 1 Connect the female end of the external power converter to the auxiliary power inlet on the back of the chassis 2 Connect the female end of the power cord to the male end of the external power converter 3 Plug the male end of the power cord into the correct voltage AC rack or wall socket 4 Verify that Auxiliary power supply is connected properly by disconnecting the primary power supply and then by observing the i
19. be installed WARNING Mount the chassis evenly and securely onto the rack Failure to observe this warning could allow the chassis to fall resulting in equipment damage and or possible injury to personnel Align the universal mounting bracket in the selected position against the side of the chassis so that the chassis installation holes are visible through the universal bracket installation holes Using a Phillips screwdriver install the three 3 screws through the mounting bracket into the installation holes on side of the chassis Repeat steps 3 and 4 for the second mounting bracket Locate four 4 screws not provided and optional clip nuts not provided for each chassis to be installed Carefully align the chassis at a secure and level position between the 19 inch site rack mounting rails Install two 2 screws through the right bracket into the right mounting rail and two 2 screws through the left bracket into the left mounting rail using the clip nuts to secure if necessary Dal m a DOGGRGR080E AEREE 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 17 yo Sisse CPSMC08xx 100 PointSystem Chassis 4 1 3 Grounding Lugs The CPSMC08xx 100 comes equipped with grounding lugs which are provided for a grounding conductor wire terminated with a two hole compression type grounding connector The grounding wire which must be a copper conductor is
20. d See the individual media converter user s guide for cable port grounding requirements 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 27 CPSMC08xx 100 PointSystem Chassis Contact Us Technical Support Technical support is available 24 hours a day United States 1 800 260 1312 International 00 1 952 941 7600 Transition Now Chat live via the Web with a Transition Networks Technical Support Specialist Log onto www transition com and click the Transition Now link Web Based Seminars Transition Networks provides 12 16 seminars per month via live web based training Log onto www transition com and click the Learning Center link E Mail Ask a question anytime by sending an e mail message to our technical support staff techsupport transition com Address Transition Networks 6475 City West Parkway Minneapolis MN 55344 USA telephone 952 941 7600 toll free 800 526 9267 fax 952 941 2322 28 CPSMC08xx 100 PointSystem Chassis Warranty Limited Lifetime Warranty Effective for products shipped May 1 1999 and after Every Transition Networks labeled product purchased after May 1 1999 will be free from defects in material and workmanship for its lifetime This warranty covers the original user only and is not transferable This warranty does not cover damage from accident acts of God neglect contamination misuse or abnormal conditions of operation or handl
21. de in modules are receiving power Proceed to the next step YES For those slide in modules where the POWER LED is NOT illuminated e Ensure the slide in module is firmly seated in the slot e Contact Tech Support 1 800 260 1312 Int l 00 1 952 941 7600 To determine if a fault is due to a software problem consult the troubleshooting section of the FocalPoint 2 0 Management Application and CPSMM100 Firmware User s Guide P N 33293 This manual is available on the enclosed application CD and on line at www transition com To determine if a fault is due to an individual or slide in module consult the troubleshooting section of the user s guide for that particular module If none of the solutions listed in this section resolves the problem contact Technical Support U S Canada 1 800 260 1312 International 00 1 952 941 7600 1 800 260 1312 International 00 1 952 941 7600 24 suljooysajqno CPSMC08xx 100 PointSystem Chassis Technical Specifications For use with Transition Networks Model CPSMCO8xx 100 or equivalent Dimensions 17 x 10 4 x 1 8 inches 432 x 264 x 46 mm Shipping Weight 8 Ibs 3 6 kg AC Power Supply Power Input 100 240 V 50 60 Hz 0 66 1 6 Amp typical with a fully loaded chassis Power Output 12 VDC at 5 Amp maximum DC Power Supply Power Input 48 VDC 38 to 58 VDC 1 6 Amp typical with a fully loaded chassis Power Output 12 VDC at 8 3 Amp maximum MTBF Mean Time Before Fail
22. dules la gooo o w e 4 99 Oo eo g 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 21 yo Sisse CPSMC08xx 100 PointSystem Chassis 5 Network Management The CPSMM100 firmware and the Foca Point application are described in the FocalPoint 2 0 Management Application and CPSMM100 Firmware user s guide P N 33293 This manual is included on the application CD and is also available on line at www transition com Transition Networks CPSMM100 firmware is embedded in the optional management modules see section 2 2 The firmware allows the network administrator to configure and manage the CPSMCO8xx 100 chassis from an attached terminal or from a remote networked computer The firmware includes the Transition Networks Command Line Interface CLI a telnet server a Web browser and an SNMP Simple Network Management Protocol agent In addition Transition Networks FocalPoint application can be installed in the networked computer to provide a graphical user interface to monitor the PointSystem chassis 5 1 Hardware Connections Network management can be accessed either through the DB 9 serial port or through the RJ 45 Ethernet port of the management modules CPSMM 120 o e 9 O a Io aASE T p RESET CPsmmi2 J RJ 45 Ethernet Port DB 9 Serial Port DB 9 7 Z QE f Roxon oct e amp ae 6 10BASE T
23. g nuts at the proper torque 3 Attach the opposite end of the properly terminated grounding conductor to the Common Bonding Network CBN for telecom installations or to an approved grounding system if required for non telecom installations Grounding Lugs Grounding Wire with a CBN for telecom installation two hole compression type or Earth Ground grounding connector 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 18 CPSMC08xx 100 PointSystem Chassis 4 2 Cascade Option The management module cascade option allows the network administrator to connect up to eight 8 CPSMCO8xx 100 chassis into one manageable stack providing a single management source for up to 55 installed media converter devices To create the cascade option the CPSMM 200 Dual Slot Master Management Module is installed in the first chassis in the series The CPSMM 210 Single Slot Expansion Management Module is installed in each subsequent chassis The CPSMM 200 management module is installed in the first 7 chassis in the series The CPSMM 210 management module is installed in each subsequent chassis O An alternative setup involves installing two CPSMM 200 Dual Slot Master Management Modules into two adjacent chassis chassis for redundant management A me a The CPSMM 200 management module is installed in the first chassis in the series
24. hassis 2 Slide in Modules 2 1 Media Converter Slide in Modules 2 1 1 2 1 2 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 Transition Networks media converter slide in modules installed in slots at the front of the chassis allow the network administrator to connect various copper and fiber optic network media over protocols that include Ethernet Fast Ethernet DS3 E3 and OC 12 as well as many others see www transition com for a complete listing NOTE Refer to the user s guide that comes with each media converter slide in module for specific information on the module s cables connectors and LED indicators Chassis Face Plates CAUTION Slots in the CPSMCO8xx 100 chassis without a slide in module installed MUST have a protective chassis face plate P N CPSFP 200 covering the empty slot for Class A compliance Install a chassis face plate over any unused chassis slot by aligning the hole in the face plate with the threaded hole in the chassis Secure the face place with the enclosed bolt a Chassis Face Plate Calculating the Power Consumption CAUTION Before installing the media converter slide in modules refer to the power consumption data for each individual media converter provided in the User s Guide shipped with each media converter The combined power consumption of all devices must not exceed the available power supply Failure to observe this caution could
25. ing including over voltage failures caused by use outside of the product s specified rating or normal wear and tear of mechanical components If the user is unsure about the proper means of installing or using the equipment contact Transition Networks free technical support services To establish original ownership and provide date of purchase please complete and return the registration card accompanying the product or register the product on line on our product registration page Transition Networks will at its option e Repair the defective product to functional specification at no charge e Replace the product with an equivalent functional product or e Refund the purchase price of a defective product To return a defective product for warranty coverage contact Transition Networks technical support department for a return authorization number Transition s technical support department can be reached through any of the following means Technical Support is available 24 hours a day via e phone 800 260 1312 x 200 or 952 941 7600 x 200 e fax 952 941 2322 e email techsupport transition com e live web chat Transition Now e voice mail 800 260 1312 x 579 or 952 941 7600 x 579 e All messages will be answered within one hour Send the defective product postage and insurance prepaid to the following address CSI Material Management Center c o Transition Networks 508 Industrial Drive Waconia MN 55387 USA Attn RETURNS DEPT
26. lluminated power LEDs on the installed slide in modules and by the chassis fan operation O Auxiliary Power Inlet ma Q Q ma e External Power Power Cord Cony rter Ajddns amod CPSMC08xx 100 PointSystem Chassis 3 2 2 DC Auxiliary Power Supply This product is intended to be used in a restricted access location Proper earthing grounding is required to ensure safe operation Grounding terminals are provided section 4 1 3 for proper grounding of the device as per customer installation requirements and local electrical codes Prior to installation use a voltmeter ohmmeter to check the wiring for the presence of earth ground A readily accessible disconnect device as part of the building installation shall be incorporated into the fixed wiring The disconnect device a 48 VDC 15 or 20A circuit breaker or switch must be included in the ungrounded supply conductor Overcurrent protection must be a 48 VDC 15 or 20A fuse or circuit breaker Read and follow all warning notices amp instructions marked on the product or included in the manual CAUTION All installation and service must be performed by qualified service personnel To power the CPSMCO8xx 100 chassis through the DC auxiliary power supply 1 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 15 Connect the female end of the external power converter to the auxiliary power inlet on
27. module protective plates from the two 2 installation slots at the far left position of the chassis oto 00 e Panel Fastener Screw 1b CPSMM 120 Single Slot Master Management Module OR CPSMM 210 Single Slot Expansion Management Module If chassis face plates are covering the installation slots remove one 1 management module protective plate from one 1 installation slot at the far left position of the chassis oo 90 e Panel Fastener Screw 2 Align the management module with the PointSystem chassis installation slot so that the panel fastener screw is to the left of the module 3 Carefully slide the management module into the installation slot while aligning the modules circuit board with the installation guides NOTE Ensure that management module is firmly seated inside the chassis 4 e the attached panel fastener screw clockwise to secure the module to the chassis 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 10 sa npouu ur 3p s CPSMC08xx 100 PointSystem Chassis 2 2 3 Replacing the Management Modules CAUTION Wear a grounding device and observe electrostatic discharge precautions when replacing media converter slide in module s Failure to observe this caution could result in damage to and subsequent failure of the management module s NOTE The management modules can be replaced while the chas
28. ning the module s circuit board with the installation guides NOTE Ensure that the slide in module is firmly seated inside the chassis 4 Push in and rotate the attached panel fastener screw clockwise to secure the slide in module to the chassis 5 Repeat steps 1 through 4 for additional slide in module s 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 7 sa npouu ur 3p s CPSMC08xx 100 PointSystem Chassis 2 2 4 Replacing the Media Converter Slide in Modules CAUTION Wear a grounding device and observe electrostatic discharge precautions when replacing media converter slide in module s Failure to observe this caution could result in damage to and subsequent failure of the media converter slide in module s NOTE The media converter slide in modules can be hot swapped To replace a media converter slide in module 1 Remove the slide in module to be replaced by loosening the panel fastener screw that secures the module to the chassis front Slide the module from the chassis 2 Align the replacement slide in module with the chassis installation slot so that the panel fastener screw is to the left 000 000 OO 00 N 3 Carefully slide the replacement slide in module into the installation slot while aligning the module s circuit board with the installation guides Panel Fastener Screw NOTE Ensure that the slide in module is firmly seated in
29. onnect device a 48 VDC 15 or 20A circuit breaker or switch must be included in the ungrounded supply conductor Overcurrent protection must be a 48 VDC 15 or 20A fuse or circuit breaker Read and follow all warning notices amp instructions marked on the product or included in the manual CAUTION All installation and service must be performed by qualified service personnel The CPSMC0810 100 includes an internal DC power supply which is accessed through the power terminal block on the front panel Power Terminal Block To power the CPSMM0810 100 chassis through the primary DC power supply 1 24 hour Technical Support Connect the 48 VDC terminal to the power terminal block connector marked 4 Turn the terminal screw clockwise to secure Connect the 48 VDC terminal to the power terminal block connector marked Turn the terminal screw clockwise to secure Connect the ground terminal to the power terminal block connector marked chassis ground Turn the terminal screw clockwise to secure Verify that chassis is powered by observing the illuminated power LEDs on the installed slide in modules and by the chassis fan operation 1 800 260 1312 International 00 1 952 941 7600 13 Ajddns 4amod CPSMC08xx 100 PointSystem Chassis 3 2 Auxiliary Power Supply 3 2 1 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 14 The CPSMCO8xx 100 ch
30. part of this work may be reproduced or used in any form or by any means graphic electronic or mechanical without written permission from Transition Networks Printed in the U S A 33270 B 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 2 CPSMC08xx 100 PointSystem Chassis Table of Contents 1 Introduction 1035 ei ata Ati tata dn aces eed 4 Tal Descriptio perrera e eb fo Aaa ant te iai a ed e iata die 4 1 2 Unpacking the CPSMCO8xx 100 Equipment 5 2 Slide in Modules 5 025444 22 0 40 s s54 0 8 8 ie Sols eee aed 6 2 1 Media Converter Slide in Modules 0 0 eee eee 6 2 1 1 Chassis Face Plates cs e acte hea geen ee ee dee eta Bae ee es 2 1 2 Calculating Power Consumption 00 000 c eee eee ee 6 2 1 3 Installing Media Converter Slide in Modules 2 0005 7 2 1 4 Replacing Media Converter Slide in Modules 8 2 2 Management Modules i Varese ea ees ee Sek tea i a RS 9 2 2 1 Three Types of Management Modules 00 00 0002 00 00s 9 2 2 2 Installing the Management Modules 2 0000s eee eee 10 2 2 3 Replacing the Management Modules 0020008 11 3 Powering the CPSMCO8xx 100 00 ce eee ee ee 12 3 1 Primary Power Supply aaa cmcteia at eae adie ek ee ee alae 12 3 1 1 AG Power Supply aaa Gide SRA Pe Mae eRe ee ni 12 31 2 DC Power Supply seine ot ee e wk eek ta OES Care B
31. power supply e Power down the chassis by disconnecting power supply NOTE Contact Technical Support for any questions concerning power supply Primary Power Supply 3 1 1 AC Power Supply The CPSMC0800 100 includes an internal AC power supply which is accessed through a power inlet on the front panel The power cord is included Power Inlet Ajddns 4amod a D_ oo To power the CPSMM0800 100 chassis through the primary AC power supply 1 Connect the female end of the power cord to the power inlet on the front panel of the chassis 2 Plug the male end of the power cord into the correct voltage rack or wall socket 3 Verify that the chassis is powered by observing the illuminated power LEDs on the installed slide in modules and by the chassis fan operation 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 12 CPSMC08xx 100 PointSystem Chassis 3 1 2 DC Power Supply This product is intended to be used in a restricted access location Proper earthing grounding is required to ensure safe operation Grounding terminals are provided section 4 1 3 for proper grounding of the device as per customer installation requirements and local electrical codes Prior to installation use a voltmeter ohmmeter to check the wiring for the presence of earth ground A readily accessible disconnect device as part of the building installation shall be incorporated into the fixed wiring The disc
32. side the chassis 4 Push in and rotate the attached panel fastener screw clockwise to secure the slide in module to the chassis 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 8 sa npouu ur 3p s CPSMC08xx 100 PointSystem Chassis 2 2 Management Modules 2 2 1 Optional network management is provided by SNMP software embedded in Transition Networks PointSystem management module s that can be installed in the CPSMCO8xx 100 chassis Transition Networks provides two such modules e CPSMM 120 Single Slot Master Management Module e CPSMM 200 Dual Slot Master Management Module Along with an additional expansion module e CPSMM 210 Single Slot Expansion Management Module Three Types of Management Modules CPSMM 120 Single Slot Master Management Module The optional CPSMM 120 Single Slot Master Management Module can be installed to enable network management of a single CPSMCO8xx 100 chassis Refer to the CPSMM 120 user s guide for more information on the CPSMM 120 Single Slot Master Management Module CPSMM 200 Dual Slot Master Management Module The optional CPSMM 200 Dual Slot Master Management Module can also be installed in the CPSMCO8xx 100 chassis to enable network management 4L asva0ol This module has all of the features of the CPSMM 120 plus a pair of cascade ports which allow multiple PointSystem chassis to be connected 1N0 Note also that this module requires
33. sis remains powered However you must configure a new IP address for the replacement management module For more information see the FocalPoint 2 0 user s guide on the enclosed application CD or on line at www transition com To replace a management module in the CPSMCO8xx 100 chassis 1 Remove the management module to be replaced by loosening the panel fastener screw that secures the module to the chassis front Slide the module from the chassis 2 Align the replacement module with the installation slot so that the panel fastener screw to the left of the module i oo 2 oo 200 e Panel Fastener Screw 3 Carefully slide the replacement management module into the installation slot while aligning the module s circuit board with the installation guides NOTE Ensure that the management module is firmly seated inside the chassis 4 Push in and rotate the attached panel fastener screw clockwise to secure the management module to the chassis 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 11 sa npouu ur 3p s CPSMC08xx 100 PointSystem Chassis 3 3 1 Powering the CPSMC08xx 100 The CPSMCO8xx 100 chassis can be powered through an AC or DC power supply An optional auxiliary power supply with instant fail over protection is also available NOTE The CPSMCO8xx 100 chassis does not have an ON OFF switch e Power up the chassis by connecting the
34. ss 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 23 JUISuI JI0m u CPSMC08xx 100 PointSystem Chassis 6 Troubleshooting 1 24 hour Technical Support Are ANY of the POWER LEDs on any of the slide in modules illuminated AND OR are the fans operating YES e The chassis is receiving power Proceed to the next step NO e Ensure all power supply cables for proper connection e Ensure the AC receptacle on the wall is supplying power e If the fuse for the AC receptacle on the wall blows repeatedly have the AC receptacle inspected by a qualified electrician e Contact Tech Support 1 800 260 1312 Intl 00 1 952 941 7600 Are ANY of the POWER LEDs on any of the slide in modules illuminated but are the fans NOT operating YES e The chassis is receiving power Proceed to the next step NO e Contact Tech Support 1 800 260 1312 Int l 00 1 952 941 7600 For the management modules CPSMM120 CPSMM200 CPSMM210 are ANY of the POWER LEDs NOT illuminated NO e All management modules are receiving power Proceed to the next step YES For those management modules where the POWER LED is NOT illuminated e Ensure the management module is firmly seated in the slot e Press the RESET button on the management module e Contact Tech Support 1 800 260 1312 Int l 00 1 952 941 7600 For the remaining slide in modules are ANY of the POWER LEDs NOT illuminated NO e All sli
35. ure MIL217F2 V5 0 hrs Bellcore7 V5 0 hrs without fans 43 277 114 896 with three 3 fans 22 972 61 715 Environment Tmra O to 40 C 32 to 104 F Manufacturer s rated ambient temperature Storage Temperature 40 to 80 C 40 to 176 F Humidity 5 to 95 non condensing Altitude O to 10 000 feet Compliance EN 55022 Class A EN 55024 FCC Class A CE Mark Warranty Lifetime Product is certified by the manufacturer to comply with DHHS Rule 21 CFR Subchapter J applicable at the date of manufacture The fiber optic transmitters on this device meets Class I Laser safety requirements per IEC 825 CDRH standards and complies with 21 CFR1040 10 and 21CFR1040 11 CAUTION Visible and Invisible Laser Radiation When Open Do Not Stare Into Beam Or View Directly With Optical Instruments CAUTION Use of controls adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure EA NET aN Declaration of Conformity Name of Mfg Transition Networks 6475 City West Parkway Minneapolis MN 55344 USA Model 8 Slot PointSystem Chassis Part Number CPSMC0800 100 CPSMC0810 100 Regulation EMC Directive 89 336 EEC Purpose To declare that the 8 Slot PointSystem Chassis to which this declaration refers is in conformity with the following standards EN 55022 1994 EN 55024 1998 FCC Part 15 Class A 21 CFR subpart J I the undersigned hereby declare that the equipment specified
Download Pdf Manuals
Related Search