Toshiba SD-W1101 DVD Recorder User Manual
Contents
1. direct exposure to the laser beam do not try to open the enclosure SD W1101 SPECIFICATIONS Data Capacity DVD RAM single amp double DVD R 2 42 GB 3 9 GB DVD ROM SINGLE SIDED SINGLE LAYER 4 7 GB DVD ROM SINGLE SIDED DOUBLE LAYER 8 5 GB DVD ROM DOUBLE SIDED SINGLE LAYER 9 4 GB DVD ROM DOUBLE SIDED DOUBLE LAYER 17 GB CD ROM Rotational Speed DVD RAM DVD ROM DVD R CD ROM Transfer Rate DVD RAM DVD ROM DVD R CD ROM Access Time Average Random Access Time e DVD RAM e DVD ROM e CD ROM Average Random Seek Time e DVD RAM e DVD ROM e CD ROM Average Start Time e DVD RAM e DVD ROM e CD ROM Data Buffer Acoustic Noise Power Supply Dimensions Weight MTBF pn 4g 650 MB 1 028 2 400 rpm 1 200 2 800 rpm single layer 1 300 3 000 rpm double layer DVD R 3 516 rpm 16X 1 350 KB second 2 700 KB second 990 2 400 KB second 16X 180 ms typ 260 ms typ 150 ms typ 120 ms typ 210 ms typ 140 ms typ 15 0 sec 12 0 sec 7 0 sec 256 kbytes 45dB 1 meter away from drive 5V 146 x 203 x 41 3mm W x Hx D 2 65 lbs 1 2kg 100 000 hours P N 460017 A02. TING CABLES SCSI Interface Cable not supplied with kit The internal SCSI inter face cable is connected to your SCSI host adapter card and fits into the socket on the back of your DVD RAM The stripe or red colored side of the rib bon cable connects to pin 1 on the drive s SCSI connec tor which is found next to the drive s power connector Carefully push the SCSI connector into the socket making sure it fits snugly If you are replacing your SCSI CD ROM connect DVD RAM to the SCSI interface connector that the CD ROM was connected to If DVD RAM is an addition to a SCSI CD ROM daisy chain the DVD RAM with a custom built SCSI interface cable not supplied with kit 3 Daisy Chaining If the DVD RAM you are installing is one of two or more SCSI devices you are connecting to your system you will need to use a custom built SCSI interface cable Remember that the terminator jumper on the DVD RAM drive must have the jumper installed when the drive is the last device in the chain Host Computer comes 7 Cable come Je DVD RAM DRIVE Terminator see note 1 SD W1101 CONNECTION ONE DRIVE SD W1101 INTERNAL DRIVE S Interface Connector Host Computer _ SCSI Cable See note 2 If connecting more DVD RAM than three SCSI DRIVE devices you need to 2 use a custom built SCSI Interface Cable see note 2 DVD RAM DRIVE N N lt 7 Install Terminator Jumper only on the last drive of BUS see no
3. TOSHIBA SD W1101 DVD RAM with REALmagic Hollywood Playback Card Installation Instructions Congratulations on your purchase of a Toshiba SD W1101 DVD RAM drive and REALmagic Hollywood DVD MPEG 2 Playback Card Kit The following information will help you in the simple installation of your new DVD RAM If you are not replacing a presently installed SCSI CD ROM with the enclosed DVD RAM additional installation hardware may be required Refer to REALmagic Hollywood User s Guide for installation instructions on the DVD MPEG 2 Playback Card CHECKING YOUR KIT PACKAGING Please unpack your DVD kit and assure that you have the following items DVD MPEG 2 PCI Playback Card compatible with all graphics cards 13 3 5mm ext audio cable 14 HDB15 9 DIN overlay cable S Video to RCA video converter cable REALmagic Accessory Kit envelope with software demo CD and Playback Card User s Guide Additional items you may need that are not included in the kit are Screwdriver mounting screws and mounting hardware SCSI interface cable SCSI host adapter board DVD CD ROM Sound Cable SYSTEM REQUIREMENT The DVD RAM kit requires the following 2MB of free hard disk space 16MB of RAM Pentium based PC or compatible 133MHz or higher PCI 2 1 compliant expansion slot VGA Card Plug and Play BIOS support Microsoft Windows 95 or higher Amplified stereo speakers ARSASI The follow steps must be performed to prop
4. erly install your DVD RAM Set DVD RAM drive jumper settings Connect audio cable Install SCSI host adapter board Attach SCSI interface cable Connect power cable Mount DVD RAM SETTING JUMPERS The block of mode select jumpers are located on the rear of the DVD RAM If the jumper covers both pins on the jumper block it is ON if Jumpers there is no jumper or only one of the pins is covered the jumper is j OFF The jumper settings include SCSI ID Parity Verify One LUN Two LUN Test and Termination SCSI ID All SCSI devices attached to your computer are assigned a SCSIID ooo oO number from 0 to 7 Your DVD RAM s SCSI ID SCSHD 0 eo 1 SCSI ID must be set so that its ID num g ber does not conflict with any other Se ake y SCSI ID l e SCSI ID device s SCSI ID in your system In 2 e 3 most cases your DVD ROM will be set CO d Sse sse to SCSI ID 4 at the factory Also note HE SCSI ID eH SCSI ID that your SCSI interface card in most HE HE gt default cases has a SCSI ID of 7 This chart oS amp YN shows the jumper settings for the eight ALE SCSI ID possible ID numbers ro Ko D Ee SCSI ID 7 Parity In the OFF mode the parity bit VERIFY ONE LUN TWO LUN ii wea tt GS Termination check function on the SCSI data bus is OOOOH oOoo activated which enhances data bus re 0m0m00000 liability Theref
5. lustrates the following features of the SD W1101 DVD RAM back panel Analog audio out connector Mode select jumper SCSI interface connector Power connector DVD RAM RECORDING CARTRIDGE When recording a DVD RAM you must use a recording cartridge There are two types of cartridges Type 1 e Cartridge is reversible side A amp B e Disc cannot be removed from cartridge e Cartridges are available with single sided or double sided discs Type 2 e Cartridge is not reversible side A only e Disc in cartridge can be removed and replaced Your SD W1101 comes with a Type single sided cartridge INSTALLING CARTRIDGE IN DVD RAM Place cartridge inside of DVD RAM tray with label facing front of drive If using a single sided DVD RAM make sure that side A is facing up TECHNICAL SUPPORT Technical support can be obtained by calling 949 455 0407 Drivers are available on BBS at 949 837 8864 or on our web site at http www toshiba com FCC DECLARATION OF CONFORMITY This equipment has been tested and found to comply with the limits for a class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio comm
6. ore the jumper should remain in the OFF mode Verify When the jumper is in OFF mode written data on the media is verified after the write operaiton One LUN Two LUN The LUN jumper sets LUN Logical Unit Number to One LUN or Two LUN mode The default setting is no jumper present which sets drive to One LUN mode Test This setting is for manufacturer use only Do not jumper Terminator ON OFF This jumper turns termination power ON or OFF If you are connecting more than one SCSI device to your system and the DVD RAM is not at the end of the chain then terminator jumper is not required PLACING DVD RAM INSIDE YOUR COMPUTER Now that you have set the jumpers you are ready to install your DVD RAM inside your computer IMPORTANT Disconnect power from your computer system before beginning installation Remove computer cover and faceplate if required Refer to your com puter system s manual for removal information If DVD RAM is replac ing another drive i e CD ROM or DVD ROM remove the drive pres ently installed in your system The SD W1101 DVD RAM can be mounted horizontally or vertically in any free half height drive slot at the front of your computer Carefully start sliding the DVD RAM into the opening with the disc tray facing the front of the computer Before you push the drive all the way in you will need to connect the SCSI interface cable and the power cable to the back of the drive CONNEC
7. slot Mount drive according to your computer s instructions The screw length should not exceed 3 0 5mm measured from outside surface of side or bottom of DVD RAM to tip of screw Replace computer cover and all outer screws Mounting frame of host computer Surface of side or bottom of DVD RAM drive Software Driver ADVD RAM software driver must be installed in your system for your computer to recognize the DVD RAM drive You may also be required to install software that was provided with your DVD MPEG card INSTALLING DVD RAM Sortware WRITE DVD INCLUDED IN KIT 1 Insert Write DVD diskette into your A drive 2 Go to Start Run and type A setup exe and press OK 3 Software driver will be installed 4 Reboot your system Usc Write DVD After installing software your DVD RAM drive will be assigned two drive letters One will be for read only media a CD icon and the other will be for DVD RAM media a removable disk icon Use your DVD RAM drive just like any other drive on your system If you want to copy a file from your hard drive to the DVD RAM just select file and drag and drop it onto DVD RAM removable disk icon DVD RAM FRONT PANEL The photo illustrates the following features of the SD W1101 DVD RAM front panel DVD loading tray BUSY LED ROMLED Load Unload Button RAMLED Emergency eject hole F DVD RAM BACK PANEL The photo il
8. te 1 SD W1101 DAISY CHAIN CONNECTION MULTIPLE DRIVES Notes 1 Terminator jumper must be jumpered when DVD RAM is the last or only device on the SCSI BUS 2 Terminator jumper should be removed when DVD is in a daisy chain and is NOT the last drive Power Cable Connect an in ternal computer power sup ply cable to the power socket at the back of the DVD RAM One side of the plug has chamfered edges so the power connector fits only one way Push plug completely into the socket making sure the plug fits correctly Audio Cable optional If you have a sound card and speakers and would like to play audio CDs on your computer you will need to get a sound cable Contact AMC our small parts supplier at 888 262 9700 Sound cables are made for the sound card you are using and the DVD RAM to which you are connecting Make sure you have this information when purchasing a sound cable The sound cable connects to your sound card at one end and the other end connects to the digital audio connector at the left rear of the DVD RAM see DVD RAM Back Panel photo on page 6 for location Refer to the instructions which came with your sound card for details on any sound driver software required Also refer to the REALmagic Hol lywood User s guide for addi tional audio connection options COMPLETING INSTALLATION After you have connected all the necessary cables push the DVD RAM completely into the computer s drive
9. unications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Re orient or relocate the receiving antenna e Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This equipment has been certified to comply with the limits for a class B computing device pursuant to FCC Rules In order to maintain compliance with FCC regulations shielded cables must be used with this equipment Operation with non approved equipment or unshielded cables is likely to result in interference to radio and TV reception The user is cautioned that changes and modifications made to the equipment without the approval of the manufacturer could void the user s authority to operate this equipment LASER CAUTION This appliance contains a laser system and is classified as a CLASS 1 LASER PRODUCT To use this model properly read this Owner s Manual carefully and keep this manual for future reference In case of any trouble with this model please contact your nearest Authorized Repair Center To prevent
Download Pdf Manuals
Related Search