Top Innovations SF-432 Iron User Manual
Contents
1. Top Innovations Inc von ASSEMBLING THE FISH Steam ost FABRIC STEAMER amp IRON MOUNTING BASE UNIT ONTO WALL MOUNTING BASE 1 Hang Steam Nozzle securely onto Steam Nozzle Hanger FIGURE 2 A 2 Align two holes on back of Water Reservoir with two hooks protruding from front of Wall Mounting Base Press Water Reservoir onto Wall Mounting Base Once pressed together slide Water Reservoir down to secure it onto Wall Mounting Base FIGURE 2 B NOTE To keep the power cord stored away when not in use cord may be wrapped around the Water Reservoir while Base Unit is mounted on the Wall Mounting Base FIGURE 2 Top Innovations Inc ASSEMBLING THE ove rah FABRIC STEAMER amp IRON Steam WVU CONNECTING THE FABRIC BRUSH CAUTION Use care when connecting Fabric Brush as Ironing Plate may be hot Do not attempt to connect Fabric Brush while unit is emitting steam 1 Slide Fabric Brush onto Steam Nozzle over Ironing Plate as shown FIGURE 3 Press down until hook on bottom of Brush FIGURE 3 A catches onto tab below Plate FIGURE 3 B Fabric Brush should now be secured in place N In order to remove Fabric Brush pull outward on hook until it slides upward over tab Pull upward on Brush to slide it over Ironing Plate and off of Steam Nozzle FIGURE 3 Top Innovations Inc2. number is located on the back or bottom of your unit Top Innovations Inc 15 TROUBLESHOOTING amp CUSTOMER SUPPORT IMPORTANT SAFETY INSTRUCTIONS 14 PROBLEM POSSIBLE CAUSE SOLUTION Plug electrical cord into outlet Reset Circuit Breaker Ground Fault Interrupter or replace fuse If you need assistance contact a licensed electrician Unit fails to heat up Heating Indicator Light does not illuminate Household Circuit Breaker Ground Fault Interrupter has tripped or blown a fuse Unit is not plugged in Unit heats up but fails to Steam Water reservoir is empty Refill water reservoir using Heating Indicator Light does procedures on page 10 of this illuminate manual Note Allow proper time for unit Mineral build up in unit Follow Removing Mineral to heat up and begin producing Build Up procedure on page 13 steam of this manual Steam Button is not being Press and hold the Steam Button pressed for a few seconds for steam to begin flowing Steam output is intermittent Mineral build up in unit It is normal for unit to periodically stop steaming for a few seconds If steam stays off for longer periods follow Removing Mineral Build Up procedure on page 13 of this manual Steam Button not being pressed continuously For continuous steam press and hold Steam Button Loud pumping sound when Low water level in water Steam Button is pressed reservoir Refill water reser
3. AGE GUIDELINES WARNING To reduce the risk of electrical shock this appliance has a three pronged plug This plug will fit in a polarized wall outlet only one way Ifthe plug does not fit fully in the outlet contact a licensed electrician to install a proper outlet DO NOT attempt to modify the plug or defeat this safety feature To reduce likelihood of circuit overload DO NOT operate another high wattage appliance on the same circuit Do not use unit with extension cords or electrical outlets that have inadequate current capacity A three prong outlet or a properly grounded adapter is necessary when using this unit If an extension cord is necessary a 10 ampere cord should be used Cords rated for less amperage may overheat Care should be taken to arrange cord so that it cannot be pulled or tripped over Unit is only meant to be used with recommended SF 432 accessories Using other types of attachments may cause damage to unit or injury When filling water reservoir do not exceed 32 oz 950 ml of water Only water should be used in unit Other cleaning agents could damage unit or cause injury When not in use while mounted to Wall Mounting Base make certain Steam Nozzle is securely mounted on the Steam Nozzle Hanger This will prevent it from being pulled off by children or pets and potentially causing injury SAVE THESE INSTRUCTIONS FOR HOUSEHOLD USE ONLY Top Innovations Inc CLEANING IRONING
4. PLATE 1 Set Lighted On Off Switch to Off position and unplug power cord from electrical outlet Remove Fabric Brush from Steam Nozzle if connected Allow Ironing Plate time to cool down completely at least 30 minutes before cleaning Clean only the outside of unit using a damp cloth with mild soap if desired DO NOT place in dishwasher Scale and other residue can be wiped off Ironing Plate with a damp cloth or non abrasive pad 6 Move Steam Nozzle over a clean cotton cloth to clean Ironing Plate and let remaining water on Ironing Plate evaporate A UN nn REMOVING MINERAL BUILD UP A common problem with steam appliances is mineral build up caused by high mineral content in many municipal water supplies The best way to avoid this is to use de mineralized or distilled water in unit If you are unable to use de mineralized or distilled water we recommend you use this procedure monthly to help avoid mineral build up 1 Set Lighted On Off Switch to Off position and unplug power cord from electrical outlet Allow unit to completely cool Remove Fabric Brush from Steam Nozzle if connected Remove Water Reservoir Cap and drain remaining water from water reservoir into sink or tub Using Measuring Cup make a mixture of 8 oz 237 ml vinegar and 8 oz 237 ml water Slowly pour water vinegar solution into water reservoir through Water Reservoir Inlet Replace Cap 6 Plug unit in and allow to heat up
5. Press the Steam Button for several minutes to allow water vinegar solution to clear Steam Nozzle of mineral deposits 7 Unplug unit and allow to cool before draining any remaining water vinegar solution from water reservoir 8 Once water reservoir is empty refill with 16 oz 473 ml of fresh water and repeat STEP 7 Repeat as necessary until vinegar odor dissipates 9 Once odor is eliminated make sure water reservoir is empty and replace Water Reservoir Cap NAUN PROPER STORAGE Preparing your Fabric Steamer amp Iron for storage is quick and simple When you have finished your steaming tasks follow the steps listed below 1 Set Lighted On Off switch to Off position and unplug power cord from electrical outlet 2 Allow unit to cool completely at least 30 minutes 3 Remove Fabric Brush from Steam Nozzle if connected 4 Remove Base Unit from Wall Mounting Base if it is mounted and drain any water remaining in water reservoir into a sink or tub 5 Mount Base Unit back onto Wall Mounting Base and wrap power cord around base Place Steam Nozzle onto Steam Nozzle Hanger 6 Alternatively store Base Unit with Steam Nozzle in a safe convenient location Top Innovations Inc USING THE FABRIC STEAMER amp IRON FABRIC STEAMER amp IRON STEAMING GARMENTS 1 Place garment on a clean rust free clothes hanger Hang within easy reach of Steam Hose Nozzle 2 Point Steam Nozzle at bottom of garmen
6. Steam AS me Fabric Steamer amp Iron Steam osi Top Innovations Inc 6655 Troost Ave Kansas City MO 64131 Tel 800 711 6617 816 584 9700 www SteamFast com customerservice topinnovations com TERTE W Printed in China PRODUCT SERIAL NUMBER For your convenience space has been provided below for you to record the serial number of your unit located on the back or bottom of the unit for easy reference when contacting our Customer Service Department by Top Innovations Inc Please read all instructions before use V060905 Mail in your warranty registration card LETTER FROM THE CEO WARRANTY INFORMATION Dear Valued Customer Congratulations on purchasing your new SF 432 Fabric Steamer amp Iron This versatile and convenient product places the power of steam in a compact and lightweight appliance with a practical and space saving design that is optimized for either table top or wall mounted use Now you can have the all of the features of a fabric steamer as well as those of an iron Combining steam power with a heated Ironing Plate the Fabric Steamer amp Iron makes creating crisp creases fast and easy Just plug it in and in minutes you are ready to easily remove wrinkles from garments draperies and upholstery In addition to smoothing fabrics you will receive the many benefits that steam provides Hot steam is environmentally friendly and uses no harsh chemicals to ge
7. Styrofoam packing material for all parts listed below To obtain possible missing parts refer to the Customer Support section on page 14 of this manual 1 2 3 A Unit FEATURES amp ACCESSORIES WALL MOUNTING BASE BASE UNIT WATER RESERVOIR FILL HOLE WATER RESERVOIR CAP WATER LEVEL WINDOWS LIGHTED ON OFF SWITCH STEAM NozzLE HANGER STEAM NOZZLE HEATING INDICATOR LIGHT STEAM BUTTON HANDLE IRONING PLATE STEAM HOSE FABRIC BRUSH MEASURING Cup 1 2 3 4 5 6 7 8 9 Top Innovations Inc FABRIC STEAMER amp IRON PRODUCT INFORMATION e The Wall Mounting Base 1 attaches to the wall as a permanent station for mounting the Base Unit saving space and providing quick convenient access to the SF 432 e The Base Unit 2 is the main body of the SF 432 housing the water reservoir which is accessed for filling via the Water Reservoir Inlet e The Water Reservoir Inlet 3 serves as the opening through which water is poured into the water reservoir The Water Reservoir Cap must be removed in order to access the Inlet The Water Reservoir Cap 4 covers the Water Reservoir Inlet keeping water contained safely inside the water reservoir The Water Level Windows 5 provide a convenient view into the water reservoir allowing the remaining water level to be easily monitored The Lighted On Off switch 6 activates and deactivates the unit and provides a clear visual indicatio
8. d the Fabric Brush is connected before following these steps j N w For first time use remove protective plastic cover that is shipped on electrical plug Plug power cord into a convenient 3 prong electrical outlet CAUTION This unit uses a grounded 3 prong electrical plug Use only in properly installed 3 prong electrical outlets Do not attempt to alter plug or circumvent this safety feature in any way Set Lighted On Off Switch to On position and verify that switch is illuminated The Heating Indicator Light will illuminate indicating that the heater is active After approximately 45 50 seconds of heating time Heating Indicator Light will deactivate Ironing Plate should now be heated and the unit is now ready to begin producing steam NOTE During use Heating Indicator Light may cycle on and off This is normal as the unit works to maintain a constant appropriate temperature Point Steam Nozzle at material you wish to steam then press and hold Steam Button After a few seconds Steam Nozzle will begin producing a flow of steam CAUTION Always be sure that Steam Nozzle is pointed in a safe direction away from yourself other people pets and plants before pressing Steam Button NOTE When unit is first turned on Steam Button must be held for approximately 10 seconds before steam flow will begin This is because water must be pumped from water reservoir into Steam Nozzle After this steam flow wi
9. egal rights and may have other rights which may vary from state to state Performance of any obligation under this warranty may be obtained by 1 Call 800 711 6617 for Return Authorization Number before returning for repair Failure to obtain a Return Authorization Number will cause a delay in warranty and out of warranty service requests 2 Include copy of purchase receipt 3 Include your name address telephone number and Return Authorization Number on returned package Please send product postage prepaid to TOP INNOVATIONS INC WARRANTY SERVICE DEPARTMENT 6655 TROOST AVE KANSAS CITY MO 64131 Should there be any missing or defective parts or accessories please contact Customer Support In most cases it is not necessary to return the entire unit We can ship most parts directly to your door Upon expiration of 1 year limited warranty you will be advised of the cost of repair before any servicing is done unless you enclose a note indicating that you would like us to proceed with repairs If you need to request warranty service or have any questions about coverage under this warranty please visit the Warranty Service Request page on our Web site www SteamFast com You may also contact the Warranty Service Department by telephone at 800 711 6617 or 816 584 9700 or e mail customerservice topinnovations com Please have your product serial number ready before contacting Warranty Service Department The serial
10. ll be near instantaneous when Button is pressed Keep the flow of steam focused on material you are steaming Using a slight back and forth motion over area you are steaming will further enhance the process GENERAL STEAMING TIPS Curtains and draperies may be steamed while still hanging To remove wrinkles from towels handkerchiefs and napkins drape them over a rod or towel rack and gently steam them Heavier fabrics may require repeated steaming to effectively remove wrinkles To remove exceptionally stubborn wrinkles steam both sides of fabric For additional assistance in removing tough wrinkles or to remove lint and other particles attach Fabric Brush to Steam Nozzle see Connecting the Fabric Brush section on page 9 of this manual Top Innovations Inc 11 SNe FABRIC STEAMER amp IRON FILLING WATER RESERVOIR WITH WATER NOTE When water level is low it is normal for water reservoir in Base Unit to emit a pumping sound Adding more water will eliminate the sound CAUTION Be sure that power cord is not connected to an electrical outlet before filling water reservoir with water 1 Unscrew Water Reservoir Cap by turning it in a counter clockwise direction FIGURE 4 A This will expose the Water Reservoir Inlet 2 Fill included Measuring Cup with water then pour into water reservoir through Inlet NOTE In order to prolong the life of your Fabric Steamer amp Iron it is recommended that de mineralized o
11. n of whether or not the unit is powered on e The Steam Nozzle Hanger 7 provides a safe and convenient place to hang the Steam Nozzle when not in use e The Steam Nozzle 8 emits a flow of hot penetrating steam when the Steam Button is pressed e The Heating Indicator Light 9 illuminates when the unit is turned on indicating that the heater is active The Light will deactivate once the Ironing Plate is heated then cycle on and off during use as the unit works to maintain a constant temperature e The Steam Button 10 is pressed in order to control the flow of steam from the Steam Nozzle e The Handle 11 is designed to stay relatively cool while providing the optimum level of safety and user comfort The Jroning Plate 12 functions similar to a conventional iron and is designed for making crisp creases e The Steam Hose 13 carries water from the water reservoir in the Base Unit to the boiler in the Steam Nozzle for conversion into steam e The Fabric Brush 14 connects to the Steam Nozzle above the Ironing Plate and is designed to work with steam in order to remove lint and gently smooth stubborn wrinkles The Measuring Cup 15 assists you in easily and consistently filling the water reservoir with the optimum amount of water 32 oz 950 ml Top Innovations Inc USING THE FABRIC STEAMER amp IRON STEAMING LINENS amp FABRICS NOTE Be sure that water reservoir has already been filled and if desire
12. r distilled water is used to avoid mineral build up 3 Repeat STEP 2 above in order to completely fill water reservoir with 32 oz 950 ml of water IMPORTANT Do not add detergents or other chemicals to water reservoir doing so may result in damage to the unit 4 Place Water Reservoir Cap back onto Water Reservoir Inlet and rotate it in a clockwise direction to secure it back into place FIGURE 4 B FIGURE 4 Top Innovations Inc ASSEMBLING THE FABRIC STEAMER amp IRON SECURING WALL MOUNTING BASE TO WALL CAUTION Be sure Wall Mounting Base is located where small children will not have access to the unit s cords when it is mounted 1 Select a location for Wall Mounting Base Be sure that Base will not prevent a door from opening or closing properly and that cords will not get closed in a door CAUTION In order to avoid electrical shock do not hang unit directly over an electrical outlet N Refer to FIGURE 1 below which illustrates how to use included screws and anchors to secure Wall Mounting Base to wall NOTE Keep in mind that the Fabric Steamer amp Iron may be used while mounted on the Wall Mounting Base Alternatively the Base Unit may be removed and used on any ordinary table top or other flat surface and mounted on the Wall Mounting Base for storage purposes only Fea tt 1 CE eee E SS ria Mount between 36 91cm and 54 137cm from floor FIGURE 1
13. t Steam will rise along inside and outside of fabric removing wrinkles Slowly slide Steam Nozzle vertically from bottom to top of garment NOTE Do not allow kinks to form in hose at any time during use 3 Direct Steam Nozzle away from garment and smooth fabric with your free hand 4 Repeat steps 3 and 4 as necessary until fabric is smooth and wrinkle free USING THE IRONING PLATE Whenever a crisp crease is desired this can be easily accomplished using the Ironing Plate A folded towel placed on a table top or other flat surface may be used if an ironing board is not conveniently available 1 Be sure Fabric Brush has been removed before proceeding CAUTION Use care when removing Fabric Brush from Ironing Plate as both may be hot and may cause burns or other injury 2 If the unit has not recently been in use allow Ironing Plate at least 45 seconds to heat up 3 To form a crease fold fabric and apply Iron Plate as you would use a regular iron Ifa steam burst is desired simply press Steam Button When you are finished using the Fabric Steamer amp Iron immediately set Lighted On Off switch to Off position and unplug power cord from electrical outlet Refer to Care and Storage Guidelines on page 13 of this manual for proper cleaning and storage procedures 12 Top Innovations Inc PRODUCT INFORMATION The following features and accessories are included with your Fabric Steamer amp Iron Carefully inspect
14. t the job done It also refreshes upholstery and helps to reduce smoke and other unpleasant odors making your garments and furniture like new again And when you re finished steaming whether you re mounting it to a wall or tucking it away into a closet or cabinet the Fabric Steamer amp Iron s versatile design makes it quick and convenient to store Top Innovations Inc would like to invite you to visit our Customer Support Web site at www SteamFast com On this Web site you will find additional information about many other exciting products that are available helpful tips on ways in which you can utilize your Fabric Steamer amp Iron and other useful information to assist you in maximizing the power of steam Enjoy your new SF 432 Fabric Steamer amp Iron Za Benny Lee Chairman and CEO Top Innovations Inc Top Innovations Inc ONE YEAR LIMITED WARRANTY If outside USA additional shipping charges may apply Top Innovations Inc warrants this product to be free from defects in material and workmanship for a period of one 1 year from the date of purchase This warranty does not cover damage caused by misuse negligence use by improper current or voltage commercial use use contrary to operating instructions or disassembly repair or alteration by any person other than Top Innovations Inc Warranty Service Department Top Innovations Inc will repair or replace at its option This warranty gives you specific l
15. voir using procedures on page 10 of this manual CUSTOMER SUPPORT For problems with your Fabric Steamer amp Iron please refer to the troubleshooting solutions located above Additional inquiries should be directed to our Customer Support services through our Web site www SteamFast com on the Service Request Web page If you do not have internet access you may also contact our Customer Support Department by telephone at 800 711 6617 or 816 584 9700 NOTE In order for our customer service representatives to help you as quickly and efficiently as possible please have the following information ready before calling Purchase information where and when you purchased this product Product Serial Number Top Innovations Inc WARNING To reduce the risk of fire electrical shock or injury the following basic safety precautions should always be followed when using an electrical appliance READ ALL INSTRUCTIONS BEFORE USE 1 Use Fabric Steamer amp Iron only for its intended purpose as indicated in this manual 2 To reduce risk of contact with hot water emitting from steam vents check appliance before each use by holding it away from body and pressing Steam Button Do not operate unit if steam vents are blocked 3 To protect against risk of electric shock do not immerse unit in water or other liquids Do not use power cord or Steam Hose as handle or allow them to be crimped 4 Lighted On Off S
16. witch should always be set to OFF position before plugging or unplugging unit from outlet Never yank cord to disconnect from outlet instead grasp plug and pull to disconnect 5 Do not allow power cord to touch hot surfaces Allow unit to cool completely before putting away Loop power cord loosely around unit when storing 6 Always disconnect unit from electrical outlet when filling with water or emptying and when not in use 7 Do not operate iron with a damaged power cord or if the iron has been dropped or damaged To avoid risk of electrical shock do not disassemble unit take it to a qualified service repair person for examination and repair Incorrect reassembly can cause a risk of electrical shock when unit is used 8 Close supervision is required for any appliance being used near children pets and plants Do not leave unit unattended while plugged in or on a table or ironing board 9 Burns can occur from touching hot metal parts hot water or steam Do not touch Ironing Plate or attempt to connect Fabric Brush while unit is in use Use caution when you turn unit upside down there may be hot water in water reservoir 10 If Heating Indicator Light does not illuminate unit is not operating normally Immediately disconnect from power supply and have unit serviced by qualified service personnel SAVE THESE INSTRUCTIONS FOR HOUSEHOLD USE ONLY Top Innovations Inc SPECIAL INSTRUCTIONS CARE AND STOR
Download Pdf Manuals
Related Search