Home

Topfield TF 5400 PVR Satellite TV System User Manual

Contents

1. button then radio service en tries will be listed in the service list To recall the television service list after adding radio services press button again With your favorite service list you can select your favorite ser vices more handily Refer to 8 5 1 for more descriptions 6 3 Transferring receiver data The digital receiver retains such data as follows e Service list e Favorite list e Preference settings It is possible to transfer receiver data to your digital receiver from another same digital receiver connecting them with a RS 232 cable 54 Listing Services To transfer receiver data perform the following steps 1 Plug one end of a RS 232 cable 9 pin D sub cable into the RS 232 port on the digital receiver and the other end into the matching port on the other digital re ceiver 2 Turn on both of them 3 Select the Installation gt Transfer Firmware gt Transfer Data to Other IRD menu 4 Restart the digital receiver NOTE You had better memorize some important data such as video settings before starting transfer to avoid resetting them 55 Chapter 7 Recording and Playing With one tuner of the digital receiver you can record a service and at the same time watch another service if the two services are provided through a same transponder The TF 5400 PVR Combo digital receiver has two tuners so that you can enjoy the following things e You can record two different
2. button Press 04 button at the position then the point starts to blink Find the other end position Press 04 button at the position again then the block turns to green and starts to be played back repeatedly Press EY button to hide the progress bar To withdraw the block press 04 button on condition that the progress bar is displayed 7 4 Editing a recording 69 7 3 6 To play back a scrambled recording If you have recorded a program from a pay service with its subscription card you can play back it as freely as one from free service Otherwise you need the subscription card for the pay service when to play back the recording file because it has been recorded without unscrambling In the recording file list purely green represents that the file has been recorded with being descrambled wholly on the other hand yellowish green represents partially descram bled one and pure yellow represents not descrambled one at all Refer to 7 1 6 for detailed descriptions about how to record a program from a pay service 7 4 Editing a recording 7 4 1 To erase a block from a recording You can cut out a block such as commercial film from a record ing file by performing the following steps 1 Start playback of a recording file you want 2 Press button to display a progress bar 3 Find one end position of a block you want to specify with E button or button 4 Press 04 button at t
3. Set the Service option to the service which provides the pro gram you want Pressing the button on this option dis plays a service list in which you can select a desired service 60 Recording and Playing There are 5 timer modes One Time means literally one time Every Day means literally every day Every Weekend means Saturday and Sunday per week Weekly means one day per week Every Weekday means from Monday to Friday per week If your favorite program is broadcasted at weekend and you wish to record every episode of the program set the Mode option to Every Weekend Set the Date option to a date on which your program will be recorded The date format is day month year day of the week Set the Start Time option to a time at which your program will be recorded You can enter it with the numeric buttons The time format is hours minute Set the Duration option to a time after which your recording will be finished The allowable maximum value is 23 hours and 55 minutes Pressing on the File Name option displays an on screen keyboard with which you can specify a file name for your timer recording If you do not specify anything it will be named after its service name For how to use the keyboard refer to 6 2 To make an entry with the above settings do press the OK command otherwise it will not be made You can edit or delete a timer entry in the timer list To delete a time
4. When you watch a program if the program has the audio track of the language designated at the 1st Audio Language it will be output If the first language is not available but the second language is available the second language s audio will be output If there is not any available language an ordinary audio will be output Apart from this setting you can select an audio track with a button See 8 5 1 3 for detailed description 3 2 Video and audio settings You have to configure the video and audio settings appropri ately to your television set and appliances 20 Preference Settings Video Output VCR Scart Type TV Aspect Ratio Display Format Sound Mode RF Output RF Channel To configure the video and au dio settings select the System Setting gt A V Output Setting menu RGB Standard 43 Letter Box Stereo PALG 36 3 2 1 Television standard The digital receiver supports two types of television standard One is the PAL standard and the other is the NTSC stan dard PAL was adopted in European countries while NTSC is adopted in USA Canada Mexico and so forth If you have a PAL television you have to set the TV Type op tion to PAL In this case if a service is broadcasted in NTSC standard the digital receiver converts it into the PAL standard for your PAL television However its quality would some what fall The opposite case brings about the same result The best thing is to watch PAL serv
5. button unceasingly until you find it 62 Recording and Playing 3 Press button to start recording 4 Press button to stop time shift 5 Press button once more to stop recording For detailed description about time shift function refer to 5 4 7 1 6 To record a pay service You can record programs from a pay service without its sub scription card However you need the subscription card when to play back the recorded programs because they are not de scrambled So it is recommended to record them with the sub scription card so that they would be descrambled In that case you can enjoy them without the subscription card like ones from free services To record a pay service s program to be descrambled perform the following steps 1 Select the pay program you want to record 2 Make sure its subscription card is inserted in the CAS slot on the front of the digital receiver 3 Start recording 4 Do not switch to any other service nor use time shift function until the program is over NOTE If you have switched over to any other service or used time shift function when recording a pay program it would be recorded without unscrambling from that position Even with a partially descrambled recording you need its subscription card to play backit 7 2 File list 63 7 2 File list 1 3 4 6 6 7 8 9 10 31103 2 31103 01 01 01 01 01 01 01 01 01 01 01 01 01 01 10 12 In re
6. receiver plugged to a wall outlet so as it can run timer events at any time The front panel The front panel of the digital receiver has buttons to operate the digital receiver and lamps and a display to indicate its status Their usage is as follows PERSONAL VIDEO RECORDER al were O srt E A mmo BODA 0 0 l ES TV STB lamp lights up while your video recorder operates instead of the digital receiver For more descriptions refer to 3 2 3 REMOTE lamp lights up whenever you press a button of the remote control STANDBY lamp lights up while the digital receiver is in standby mode Status display displays the current time in standby mode and displays the current status of the digital receiver in operation mode STANDBY button switches the digital receiver between standby mode and operation mode MENU button displays the main menu It is also used to return to the previous menu from a submenu CHANNEL A Y buttons move to the next or previous ser vice They are also used to navigate in menus and in teractive screens 4 Introduction VOLUME lt 4 gt buttons increase and decrease the volume They are also used to change the options for a menu item OK button displays the service list It is also used to select menu items 1 2 Controlling the digital receiver 5 1 2 2 The remote control O button switches the digit
7. space of 10 centimeter around it For the physical speci fication of the digital receiver refer to Table 2 2 Protect the power cord from being walked on or pinched Never open the digital receiver casing under any cir cumstances Warranty claims are excluded for the dam age resulting from improper handling Refer all servicing to qualified service personnel Table 2 1 Power specification Input voltage 90 to 250 V AC 50 60 Hz Power consumption 40W at maximum in operation 8 W in standby 2 3 Rear panel connections 11 Table 2 2 Physical specification Size 340x 60x 265 mm Weight 3 4 kg Operating temperature 0 to 45 C Storage temperature 40 to 80 C Storage relative humidity 5 to 95 2 3 Rear panel connections The TF 5400 PVR Combo has a wide range of connections on the back panel 1 3 5 11 4am VIDEO bla o H D our LNB IN ANT tile o lt IAZ w o 0 O CEA E P en if our RFLooPour AUDIO s viDEO Ver usa sipor RS 232 2 4 6 7 9 13 10 12 14 Check up what connections your television set has in compar ison with the digital receiver LNB IN Broadcasting signal input socket for the first tuner IF OUT Broadcasting signal output socket from the first tuner ANT Broadcasting signal input socket for the second tuner RF LOOP OUT Broadcasting signal output socket from the second tuner VIDEO Composite video output
8. 29 4 1 Searching satellite broadcasting services 29 4 1 1 Configuring LNB settings o 29 4 1 2 Configuring DiSEqC 1 2 settings 31 4 13 Configuring USALS settings 33 41 4 Searching services lt s socas rosarios emisa 34 4 2 Searching terrestrial broadcasting services 37 So COPY berries a WE we ge a 38 44 Resetting to factory settings o o 38 5 Daily Usage 39 DA Watching television OS ee oe We ee we 39 5 1 1 Watching favorite services o o 41 5 1 2 Viewing program information 42 513 Selecting audietrack 2 2 2252 siees e084 43 52 53 5 4 D5 Listing Services 6 1 Editing the service list 6 2 Editing the favorite list 6 3 Transferring receiver data Recording and Playing 7 1 Recording a program Tin 7 3 5 1 4 Selecting subtitle track 5 1 5 Viewing teletext Viewing electronic program guide Watching multifeed program Watching by time shift Watching by picture in picture Immediate recording by the remote control Recording by the recording menu Making a timer recording Recording by electronic program guide Recording when using time shift To record a pay service Playing back a recording To play back in slow motion To play back in fast motion To play back recordings in sequence To make a bookmark To play back a recording repeatedly To play back a scrambled
9. Eastern Australia Guam Vladivostok GMT 11 00 Magadan Solomon Islands New Caledonia GMT 12 00 Fiji Auckland Wellington Kamchatka 3 4 Parental control In general a television program is labeled a rating according to the level of violence nudity and language of its content When you are watching a program you can check its program rating on the information box Refer the information box to 5 1 2 You can prevent your children from watching specific pro grams by specifying a basis rating 26 Preference Settings To specify a basis rating select E the System Setting gt Parental 4 No block Control menu At this time you Change PIN Code Access Control have to enter a Personal Identifi cation Number PIN The num ber is initially set to 0000 If you wish to restrict 15 or above rated programs set the Cen sorship option to 15 age Setting it to No block restricts no program on the other hand setting it to Total block restricts every program NOTE If a program does not have any rating information your re striction setting will not take effect If anyone try to watch a program that is out of the basis rating the person has to enter the personal identification number To change the number select the Change PIN Code menu then an input box appears You have to enter a desired num ber twice for confirmation You can also restrict uses of some menus Selecting the Access Con
10. Longitude and My Latitude options with the and numeric buttons 3 Input the position of your selected satellite to the Satel 34 Service Search lite Angle if it is not correct 4 Select the Goto the position command Then the antenna will turn toward your selected satellite calculating its position 5 If the receiving quality which is displayed on the right bottom on the screen is not good tune the antenna finely with the commands of the Move menu The changed po sition is automatically saved at one At this time you had better check the receiving quality of every trans ponder and choose the best one at the Transponder or Frequency option It will be helpful to your fine tuning 4 1 4 Searching services To perform service search select the Installation gt Satellite Set ting gt Service Search menu Satellite Name Search Mode Symbol Rate FTA Scrambled Start Search LNB Setting 5150MHz Start Searching for digital Movos itom OK Start Searching MNU Provious Monu There are four service search methods e Searching every service of a satellite e Searching every service of a transponder e Searching one service of a transponder e Searching every service of a SMATV Satellite Master Antenna Television transponder To search every service of a satellite perform the following steps 4 1 Searching satellite broadcasting services 35 1 Choose your desired satellite at the Satel
11. Record pause 57 Record Start 59 Recording 58 recording file list 63 Rename 40 50 64 RF Channel 23 RF IN 12 16 RF LOOP OUT 11 RF OUT 12 16 23 RF Output 23 RS 232 12 54 79 80 S VIDEO 12 14 S PDIF 12 S PIDF 15 Satellite 40 41 51 58 Satellite Angle 34 satellite list 30 Satellite Name 28 30 32 33 35 36 Save 70 Search Mode 35 37 Service 58 59 service list 39 Service Search 34 36 37 Services Copy 38 Show Provider 40 Size 64 SMATV 34 SMATV 36 Sort 51 Sorting 41 64 Sound Mode 23 Start 77 Start Time 58 60 stereo 23 Stop 59 78 79 Store 33 subtitle 43 Symbol Rate 35 36 System ID 76 System Setting 27 TAP 74 tap 74 teletext 44 television service list 50 53 Terrestrial Search 37 TFD Down 78 79 TFDN_USB 77 78 Time 64 time format 24 Time Offset 24 Time Setting 26 time shift 45 84 INDEX Time Shifting 27 46 timer list 59 Timer Setting 59 Total block 26 Transfer Data to Other IRD 54 Transfer Firmware to Other IRD 80 Transponder 32 34 51 transponder 1 Tuner 40 Tuner 1 to Tuner 2 38 Tuner 2 to Tuner 1 38 Tuner Select 28 59 TV 12 14 59 TV Aspect Ratio 21 22 TV Type 20 Type 59 Unlocked 65 USALS 33 USALS Setting 33 USB 12 72 78 User 32 VCR 12 16 VCR Scart Type 21 VIDEO 11 13 15 Video Output 21 Weekly 60 wide screen television 21 Wind R
12. current service entry select the Delete com 5 1 Watching television 41 mand then a confirmation box appears Once you con firm with Yes the entry will be deleted If you want to add the entry to the service list as before you have to perform service search again Refer service search to 4 1 4 e To add the current service entry into a favorite list select the Add to FAV command then the favorite list appears Once you select a desired group the entry will be added in it e You can additionally sort the service list with the Sorting option as follows Default by service number Alphabetic by service name Satellite by satellite FTA CAS from free services to pay services CAS FTA from pay services to free services Provider by service provider Fav NoFav from favorite services to unfavorite ser vices For how to edit the service list refer to 8 6 1 5 1 1 Watching favorite services You can select a service to watch in the favorite list as well as in the service list To display your favorite list press the button then a favorite group list will be displayed Whenever moving the highlight bar of the group list up or down favorite services belonging to a highlighted group are listed 42 Daily Usage To select a favorite service of a group press the button News 2 NILE NEWS Movie 3 AL ALAM favorite list becomes movable Once you select a desired entry with the Ok button the selected service
13. on the digital receiver s hard disk See 87 4 4 button displays the service list for picture in picture or specifies a block for repeated playback If you do not have wide screen television but normal screen television pressing the o button changes depending on broad casting conditions the display format as follows When you are viewing a wide screen television pressing the o button cycles through the display format options as follows 4 3 Center Extract 4 3 Letter Box 16 9 0 a e and 4 buttons have additional different func tions per menu besides their own function Their functions will be guided in the on screen help 8 Introduction 1 3 What is common interface Some broadcasts are scrambled so that only paid subscribers can enjoy them Scrambled services can only be viewed with a Conditional Access Module CAM and a subscription card belonging with the scrambling system Common Interface CI is an interface for condi tional access modules The front of the digital receiver has two common interface slots Va To watch a pay service you should take the following steps 1 Purchase a conditional access module and a subscrip tion card for the pay service you want to watch 2 Insert the subscription card into the conditional access module 3 insert the conditional access module to a common inter face slot on the front of the digital receiver To view the information about t
14. recorder or such an appliance from the VCR SCART The digital receiver will operate differently depending on the set ting of the VCR Scart Type option If the option is set to Stan dard the digital receiver will pass the video from the video recorder to your television when the video recorder starts play back But if the option is set to External A V the digital re ceiver will not pass the video even though the video recorder starts playback To pass it you have to press EY button NOTE In this case it is impossible that the digital receiver records the video that the video recorder plays back because the digital receiver is just a bypass for the video recorder 3 2 4 Television aspect ratio If you have a wide screen television set the TV Aspect Ratio option to 16 9 22 Preference Settings You can enjoy well both wide screen programs and normal screen programs with your wide screen television as the above figures show The left figure shows a wide picture displayed in the wide screen and the right figure shows a normal picture displayed in the wide screen If you have a normal screen television set the TV Aspect Ratio option to 4 3 You cannot fully enjoy wide screen programs with your normal screen television as the above figures show The left figure shows a normal picture displayed in the normal screen To watch wide screen programs in the shape like the center fig ure set the 16 9 Display Format
15. recording 43 44 44 45 45 47 49 49 51 53 vi CONTENTS 7 4 79 7 6 7 7 EAT AFELMA eS 74 1 To erase a block from a recording 74 2 To store a block from a recording Pilsving 1 AAA Formatting hard disk o 0 00002 o Transferring recording files 00 9 lt lt 8 Topfield Application Program 9 Firmware Update 91 22 9 3 9 4 Index From a broadcaster o From your computer via USB port From your computer via RS 232 p0rt From another digital receiver via RS 232 port 74 76 77 77 78 79 81 Chapter 1 Introduction 1 1 Introduction The TF 5400 PVR Combo digital receiver is fully compliant with the international Digital Video Broadcasting DVB standard and can receive digital broadcasts For its operation you need an antenna which must be installed appropriately NOTE In general we equate a channel with a frequency However unlike analog broadcasts digital broadcasts are not all as signed to their own frequencies instead multiple television and radio broadcasts are transmitted through a single fre quency The frequency in digital broadcasting is usually called transponder To reduce confusion the word service is prefer ably used than channel as the term indicating one television or radio broadcast in this document The TF5400 PVR Combo digital receiver has features as fo
16. recording is started pressing displays a record ing control box like the next fig ure in which you can specify its duration on which it will be ended the current recording will be stopped after the time set to the Duration option If the information about the next programs is provided through the electronic program guide the After 7 1 Recording a program 57 this program and After next program options would be avail able Once the After this program option is selected the cur rent recording will be stopped the moment the current pro gram ends likewise once the After next program option is se lected the current recording will be stopped the moment the next program ends Selecting the Record pause command pauses recording When you press button again to display the recording control box the Record continue command is displayed instead Se lecting the Record continue command resumes recording To stop recording press but ton Then a confirmation box like the next figure appears which shows the information of programs being recorded at the moment Select a program you want to stop After a recording is started you can switch to and watch any other service during the recording To record another service additionally switch to a service you want to record and press O button Once a recording is started it is put on the recording file list even though it is not finished yet The recording file i
17. services while watching two other different services only if two or more services are provided in a same transponder and the other ser vices are provided in another same transponder You can watch two services at the same time by the picture in picture feature in this case For detailed descriptions about the picture in picture feature refer to 8 5 5 e You can record two different services while watching one of them by the time shift feature For detailed de scriptions about the time shift feature refer to 5 4 e You can record two different services while playing a recording back e When you play and view a recording you can view a service in subpicture by the picture in picture feature 56 Recording and Playing 7 1 Recording a program Once a recording is started a recording symbol like the next figure will be displayed on the right top of the screen for a few seconds When you are watching a service different from the service being recorded you can view a number on the center of the symbol which indicates the order that the recording is started The outer circle of the recording symbol indicates progress rate NOTE When a recording is finished it might not be saved if its recording duration is less than 1 minute 7 1 1 Immediate recording by the remote control To record a program you are watching at present press O button To pause recording press O button To resume it press O button again After a
18. the copying symbol indicates progress rate 7 5 Playing a MP3 71 NOTE If copying time is less than about 1 minute the copying will not be done successfully It is recommended not to change the playback speed 7 5 Playing a MP3 To play a MP3 file with the digital receiver you have to trans fer your MP3 files to the digital receiver from your personal computer For how to transfer your MP3 files to the digital receiver refer to 7 7 To play a MP3 file perform the following steps 1 Press 3 button and then press button or ED but ton to display the MP3 file list 2 Put the highlight bar on a file entry you want to play If you want to play several files select them with but ton 3 Press button to start play 4 To see the detailed information about a MP3 file being played press UD to display an information box The information box shows its file name album artist dura tion and so on 5 To stop play press O button When a MP3 file is being played pressing linefigRepeatButton turns around repeat mode symbol of which is displayed on the information box gt symbol represents that the current MP3 file will be played repeatedly gt symbol represents that all selected MP3 files will be played repeatedly in turn To play all MP3 files in a subdirectory select a desired direc tory and press O button 72 Recording and Playing 7 6 Formatting hard disk To format the hard disk of t
19. through a service search You can rename move lock or delete service entries in your service list To edit your service list se lect the Organizing Satellite Ser vices menu then an editable Function Browse AL EMARAT Rename 2 NILE NEWS Hove AL ALAM service list appears Lock KUWAIT SPACE Skip 5 IRIB3 Delete macaut Sort macau3 g macaud 10 macaus 11 macau6 Aslasat2 C 4148 MHz 11860 K8 To perform an editing work put the highlight bar on a desired command in the editing command list on the left column and press the button Then the highlight bar of the service list on the right column becomes movable that is you can select 50 Listing Services a service entry to edit with the selected command To select another command after the command execution press the button then the highlight bar of the command list becomes movable Whenever pressing the button the highlight bar of each column becomes movable in turn To edit the radio service list press amp button then radio ser vice entries will be listed in the service list To recall the tele vision service list after editing works press button again To rename a service entry select the Rename command in the editing command list and select a desired service entry to re name in the service list then an on screen keyboard appears For how to use the keyboard refer to 6 2 Unlike analog broadcasts each service does not have
20. track if available EXIT button is used to leave the current screen button displays teletext if available ED button does backward playback or scan Subse quent presses change the speed of playback button plays a recorded program or displays the progress bar for navigation when playback has already started button does fast playback or forward scan Subse quent presses change the speed of playback button starts slow motion playback Subsequent presses change the speed of playback button is used to stop a playback to stop a record ing or to jump back to live television from time shifted television O button starts a recording 1 2 Controlling the digital receiver 7 MU button pauses live television and playback of a recorded program O E button changes the position of picture in picture coun terclockwise and jumps to the end of recording in play back O button changes the position of picture in picture clock wise and jumps to the beginning of recording in play back e button displays the satellite list with their service list and swaps the picture in picture with the main pic ture See 8 5 5 O button displays resizes or hides the picture in picture ca button makes a bookmark during playback or time shift E button plays from the next bookmark position button is used to edit a recording button displays the list of recorded programs that have been saved
21. 3 zip 367KB BS How to use Altair is as follows 1 Select a file to transfer The left hand list box displays recording files in the digital receiver and the right hand list box displays files in your computer 2 To start a transfer from the digital receiver to your com puter press the right arrow button 3 To start a transfer from your computer to the digital re ceiver press the left arrow button 74 Topfield Application Program Chapter 8 Topfield Application Program If you are good at programming with C language you can make a program executable in the digital receiver We call this Topfield Application Program TAP In making a TAP it is recommended to use Diab compiler of Wind River whose web site address is http www windriver com Some vari ants of GCC compiler also might perhaps be available as a compiler for TAPs You can get the Application Program In terface API libraries for TAPs from the Topfield web site http www i topfield com Your TAPs will be run under the following conditions e Their extension name is tap If they have any other ex tension name they will be ignored e They are in the Program Files folder If they are in other folders they will be ignored For how to transfer your program to the digital receiver refer to 7 7 To run a TAP in the digital receiver perform the following steps 75 1 Press button to display the program file list 2 P
22. At this time you had bet ter check the receiving quality of every transponder and choose the best one at the Transponder or Frequency option It will be helpful to your fine tuning 4 1 Searching satellite broadcasting services 33 5 Finally select the Store command at the Motor Control menu to save the tuned position when the receiving qual ity has turned good There are more motor control commands for installers but this manual does not describe them If you are an installer refer them to the manual for the STAB rotor 4 1 3 Configuring USALS settings USALS Universal Satellite Automatic Location System also known as DiSEqC 1 3 calculates the positions of all available satellites from your location Compared to DiSEqC 1 2 it is no longer required to manually search and store every satel lite position Just by pointing to a known satellite position is enough This position will act as the central point The USALS will then calculate positions of visible satellites To use USALS select the Instal lation gt Satellite Setting gt US lt r lab ALS Setting menu Fai At first you have to set the Mo torized DiSEqC 1 3 option to Enable 3001 V1 7760 For USALS Select Enable m Select Position MIN Previous Menu To calculate every satellite position perform the following steps 1 Choose your desired satellite at the Satellite Name op tion 2 Input your location to the My
23. Kong Macao Republic of Ireland South Africa United Kingdom Czech Republic Hungary Poland Bahamas Belgium Bolivia Chile Ecuador Fiji Guam Jamaica Mexico Panama Peru United States Venezuela Set the RF Channel option to a channel number as you de sire You have to tune your television to the channel set to this option to watch television If you have connected your analog television antenna to the RF IN you can watch analog broadcasts via the digital re ceiver Local time setting You should set your local time for timer events If you did not set the local time right the program time table provided 24 Preference Settings by the electronic program guide may also be distrustful Refer the electronic program guide to 8 5 2 Select the System Setting gt Lo cal Time Setting menu Time Offset GMT Collection transponder oU Changes the time setting mode In order to change the local time set It to the manual mode Moves item 4 Selects Item MENU Previous Menu You can set the local time either manually or automatically using Greenwich Mean Time GMT However it is recom mended to use the Greenwich mean time To set the local time with GMT perform the following steps 1 Set the Mode option to Auto 2 Set the Time Offset option to the time difference belong ing to your time zone referring to Table 3 2 With the above settings the digital receiver will scan all transpon
24. TF 5400 PVR Combo User Guide Digital Satellite amp Terrestrial Receiver Personal Video Recorder Digital Video iii Contents 1 Introduction 1 LI Tntroduchi n nc ee ri eee eee ARE RRA 1 12 Controlling the digital receiver oe o 2 2 2 Lal Te roe pened ee ee Ee SE Oe ee ES bs 3 122 Theremete contral 06 co eee ee eee hee ee es 5 13 Whatis common interface lt io soo cco 505 5 be eS 8 2 Setup 9 L e AA 9 22 Safety precautions 2 555 a 9 2 0 Rear panel connections ee ee ee eee 11 2 4 Connecting up your digital receiver 13 2 4 1 Connecting to the antenna o o 13 2 4 2 Connecting to your television 13 2 43 Connecting to your video cassette recorder 16 2 5 Inserting batteries in the remote control 16 3 Preference Settings 18 al Laniguagestllags o ee ew 18 iv CONTENTS 32 Video md Ud EEES ie a ee ee eee Ee a 19 32 1 Television standard 2 26 522845858454 20 32a Colormoda vcd ee ee ee Na 20 3 2 3 Video cassette recorder 2 21 3 2 4 Television aspect ratio o ooo ooo 21 S20 OU OE a RA 22 po REQUIPUE dosis A Se ERA EG 23 o ie sere ee ek ee we BE 23 oe Parentalogmtrol ie ciao io NG ee be ee Se ee ead 25 35 Adjusting om screen display 2 i 6 oes ee ee erus 27 3 6 Touse the time shift feature 27 3 7 Setting for MediaHighwayEPG 27 4 Service Search
25. a proper service number in digital broadcastings Service numbers are assigned to services just in order that services get found through service searches So you can reassign a service number to a service Moving a service entry is the same as reassigning a service number To move a service entry select the Move com mand in the editing command list and select a desired service entry to move in the service list then the selected entry be comes darker Move it to a desired place and press the button The entry gets renumbered as it moves You can lock some services in order to restrain your children from watching those services To lock a service entry select the Lock command in the editing command list and select a desired service entry to lock in the service list Then a lock symbol o will be marked on the selected entry If anyone try to watch a locked service the person has to enter the per sonal identification number that is set in the Change PIN Code menu For how to set personal identification number refer to 3 4 Pressing the button on a locked entry in the service list unlocks it To delete a service entry select the Delete command in the editing command list and select a desired service entry to delete 6 2 Editing the favorite list 51 in the service list You can select more entries to delete After your selections pressing the button displays a confirma tion box Once you reply with Yes on the confirmation box the s
26. ack after selecting all of your entries The selected recording files are played back in sequence that they are numbered 7 3 4 To make a bookmark You can specify a playback po sition as a bookmark with button and jump to the posi tion with button You can make 64 bookmarks at maxi mum Bookmarks are stored with the recording file so that you can use them again after wards To use this utility per form the following steps 39 0 5Min 1 Start playback of a recording file you want 68 Recording and Playing To add a bookmark press button at a position you want To jump to a following bookmark press button To delete a bookmark jump to the bookmark you want and press button When there is no preset bookmark pressing button makes a jump forward 30 seconds 7 3 5 To play back a recording repeatedly The digital receiver can play back a recording file repeatedly both in whole and in part To play back a recording file repeatedly in whole press 00 button on condition that the progress bar is hidden Then an information box with a repeat symbol gt is displayed To quit the repeated playback press CO button again To play back a recording file repeatedly in part perform the following steps 1 2 3 Start playback of a recording file you want Press EY button to display a progress bar Find one end position of a block you want to specify with button or
27. al receiver between standby mode and operation mode switches off the sound tem porarily Press again to switch it back on button displays the RF set ting menu See 3 2 6 O button switches the output of the TV SCART socket between the digital receiver and the device connected to the VCR SCART socket See 8 3 2 3 for detailed de scription MY button sets a sleep timer Numeric buttons are used to en ter service numbers and option values O button switches between the current service and the previ ously viewed one button displays more infor mation about the current pro gram or a program highlighted in the electornic program guide button displays the electronic program guide button switches between television services and ra dio services 6 Introduction O e 000 0 O O eS button displays the main menu Itis also used to return to the previous menu from a submenu button is used to select an audio track and sound mode or a multifeed service if available V buttons increase and decrease the volume They are also used to change the options for a menu item P buttons move to the next or previous service They are also used to navigate in menus and interactive screens OK button displays the service list It is also used to se lect menu items FAV button displays the favorite list g button is used to select a subtitle
28. cording a program it is stored as a file in the built in hard disk of the digital receiver You can choose and play back a recording file you want in the recording file list In addition to the recording file list there are MP3 file list and TAP file list With the digital receiver you can enjoy music or audio books of MP3 format in the same manner as playing back a recording file Refer TAP to Chapter 8 To see the recording file list Welt um Zwolf 2 Die sch nen Wilden 2 Die sch nen Wilden 4 Avenzio Sch ner leben Die sch nen Wilden Die sch nen Wilden 3 Welt um Zw lf 4 Welt um Zwolf 3 Welt um Zw lf ABC TV1 ProSieben DVBT Infomagazin 430 MB 15Min 01 01 2004 00 01 147564 MB Free 152625 MB New Folder Move to Folder Options Delete File 42 Information press button To turn to another list press O button or EY button In a file list a file entry is comprised of the following informa tion file number file name recording time file size and so on You are able to play back move delete rename and lock a file entry in a file list You are also able to sort the file entries by file name recording time or file size Moreover you can make a new folder To make a new folder To make a new folder press button Then a new folder named GROUP is created You can rename the folder in the same manner as renaming a file entry 64 Recording and Playing To move a file to another
29. ctory Setting 38 Fav NoFav 41 51 File Name 58 60 Find 78 79 Firmware Upgrade 77 folder list 64 Format Hard Disk 72 Frequency 32 34 36 FTA 36 37 FTA CAS 36 37 FTA only 36 37 FTA CAS 41 51 FTA Scrambled 36 37 GCC 74 GMT 24 Goto 32 Goto the position 34 Home Transponder 28 IF OUT 11 Info Box Display Time 27 Info Box Position 27 information box 42 IRD Status 76 K band 30 Language Setting 18 Letter Box 22 LNB 30 LNB Frequency 30 31 LNB IN 11 13 LNB Power 31 LNB Setting 30 Local Time 24 Local Time Setting 24 Lock 40 50 65 Locked 65 Manual 35 37 MediaHighway 27 MediaHighway 28 MediaHighway EPG 28 Menu Language 18 Mini A 31 Mode 24 60 mono 23 Motor Control 32 33 Motorized DiSEqC 1 2 32 Motorized DiSEqC 1 3 33 Move 34 50 Movement 32 multifeed 45 My Latitude 33 My Longitude 33 NEW 52 No block 26 normal screen television 22 NTSC 20 on screen keyboard 52 One Time 60 option list 64 Organizing Favorites 51 Organizing Satellite Services 49 OSD Transparency 27 Other 30 83 PAL 20 Parental Control 26 65 personal identification number 65 picture in picture 47 PID 36 PID 36 PIN 26 Polarization 35 36 program file list 75 Program Files 74 progress bar 66 Provider 41 51 Quick 58 Radio 59 radio service list 50 Record 59 Record continue 57 Record No 58
30. d Press the button A lock symbol o is displayed on the file entry aoa FON When you press the button on a locked file entry to play it back you must enter the personal identification number spec ified in the Parental Control menu For the Parental Control menu refer to 3 4 NOTE This function is available only in the recording file list 7 3 Playing back a recording When recording a program all of service characteristics are recorded as they are So in playing back a recording file you can enjoy its audio tracks subtitle tracks and teletext if avail able How to play back a recording file is as follows 1 Press button to display the recording file list 2 Put the highlight bar on a file entry you want to play back 3 Press the OK button to start playback 4 To stop playback press O button 66 Recording and Playing Once a playback is started a playback symbol like the next figure will be displayed on the right top of the screen for a few seconds The outer circle of the playback symbol indicates progress rate During a playback you can enjoy the following tricks e To see the detailed information about a recording file be ing played back press to display an information box The information box shows its file name broad caster information service information duration and so on e To pause playback press O button To resume it press O button e To find a desired playback
31. ders specified one by one until to get the Greenwich mean time Make sure that your local time is displayed right on the Local Time option To set the local time yourself set the Mode option to Man ual and enter your local time to the Local Time option with the numeric buttons The time format is day month year 24 hour minute 3 4 Parental control 25 Table 3 2 Time offset table Time offset City GMT 12 00 Eniwetok Kwajalein GMT 11 00 Midway Island Samoa GMT 10 00 Hawaii GMT 09 00 Alaska GMT 08 00 Pacific Time US Canada GMT 07 00 Mountain Time US Canada GMT 06 00 Central Time US Canada Mexico City GMT 05 00 Eastern Time US Canada Bogota Lima GMT 04 00 Atlantic Time Canada La Paz GMT 03 30 Newfoundland GMT 03 00 Brazil Georgetown Buenos Aries GMT 02 00 Mid Atlantic GMT 01 00 Azores Cape Verde Islands GMT London Lisbon Casablanca GMT 1 00 Paris Brussels Copenhagen Madrid GMT 2 00 South Africa Kaliningrad GMT 3 00 Baghdad Riyadh Moscow St Petersburg GMT 3 30 Tehran GMT 4 00 Abu Dhabi Muscat Baku Tbilisi GMT 4 30 Kabul GMT 5 00 Ekaterinburg Islamabad Karachi Tashkent GMT 5 30 Bombay Calcutta Madras New Delhi GMT 6 00 Almaty Dhaka Colombo GMT 7 00 Bangkok Hanoi Jakarta GMT 8 00 Beijing Perth Singapore Hong Kong GMT 9 00 Tokyo Seoul Osaka Sapporo Yakutsk GMT 9 30 Adelaide Darwin GMT 10 00
32. elected service entries will be deleted The selected service entry will be If you want to undo the deleted service entries you have nothing to do but perform service search again Once you select the Sort command in the editing command list an option list appears You can sort the service list with an option of the followings Default by service number Alphabetic by service name Satellite by satellite FTA CAS from free services to pay services CAS FTA from pay services to free services Provider by service provider Fav NoFav from favorite services to unfavorite services Transponder by transponder 6 2 Editing the favorite list You can make your own favorite service list To edit your favorite list select the Organizing Favorites menu then an ed itable favorite list appears 52 Listing Services There are a group list on the left column a favorite list on the center column and a service list on the right column NILE NEWS FASHION TV macau 65 RAI International 66 TVE 7 RTPI You can add a favorite entry by performing the following steps 1 Put the highlight bar on a desired group entry in the group list and press the OK button 2 Then the highlight bar of the service list becomes mov able Put the highlight bar on a desired service entry and press the OK button 3 Then the selected service entry is added in the favorite list You can select more entries to add 4 Press the button
33. ereo audio But if you do with a conversion cable such as SCART to Component you have to make audio con nections To use the S Video connector You should prepare a S Video cable to use the S Video connector Plug one ends of the cable into the S VIDEO socket on the digital receiver and the other end into the matching Ter socket on your television 2 4 Connecting up your digital receiver 15 To use the composite video connector 4 De To connect the audio connectors LA Te To use the RF connector You should prepare a composite video ca ble RCA cable to use the composite video connector Plug one end of the cable into the VIDEO yellow socket on the digital re ceiver and the other end into the matching socket on your television You should prepare an audio cable RCA ca ble to connect the audio connectors Plug one ends of the cable into the AUDIO L white and AUDIO R red sockets on the digital receiver and the other ends into the matching sockets on your television or au dio system To enjoy Dolby digital audio your televi sion or audio system must be able to decode Dolby digital audio and you should prepare a S PDIF cable Plug one end of the ca ble into the S PIDF socket on the digital re ceiver and the other end into the matching socket on your audio system If your television does not have any video and audio input you will need to use the radio frequency output from the dig ital
34. ervals For example assume a movie would Order Starting time g be broadcasted five times like the ta 1 13 00 PM ble on the left Even if you have 2 13 15 PM missed the first broadcasting you can 3 13 30 PM use the rest to watch the movie 4 13 45 PM 5 14 00 PM If the current program provides multifeed service the multi feed symbol im will be marked on the information box To use multifeed service press the Q button then available mul tifeed entries will be listed Once you select one it will be presented At this time you have to press the a button once more to select audio tracks 5 4 Watching by time shift When you are watching a program you can reverse and watch it again as if it is a recording This function is called time shift When you are watching a program using the time shift func tion it is in fact being recorded temporarily 46 Daily Usage To use the time shift function the Time Shifting option have to be set to Enable Refer the Time Shifting option to 8 3 6 How to use the time shift func tion is as follows Press EY button then a time shift begins as a progress bar appears The progress bar has two pointers One indicates recording position and the other indicates a playback position While this bar is on display you can move the program backward or forward Pressing O makes the progress bar appear and disappear alterna tively To find a desired playback position pres
35. ew firmware file Download 2 Press the Download button to start the file transfer Stop and Exit 3 Press the Stop button to cancel the Message file transfer 4 Restart the digital receiver 9 3 From your computer via RS 232 port It is possible to transfer a new firmware to the digital receiver from your computer connecting them with a RS 232 cable You need TFD Down the firmware transfer utility for this which is available at the Topfield web site http www i topfield com To update the firmware with this method perform the follow ing steps 9 4 From another digital receiver via RS 232 port 79 Download a new firmware applicable to the digital receiver from the Topfield web site Plug one end of a RS 232 cable 9 pin D sub cable into the RS 232 port on the digital receiver and the other end into the matching port on your computer Turn on the digital receiver Run TFD Down How to use TFD Down is as follows TFD DownLoad Manager 1 File Name D WMyTaskwWTopfieldUlp Find Download Port Setup Stop Exit Message 3 TFD File Download Manager Press Find button to select the new firmware file Press Download button to start the file transfer Press Stop button to cancel the file transfer Restart the digital receiver 9 4 From another digital receiver via RS 232 port It is possible to transfer a new firmware to the digital rece
36. f the televi sion service you are watching is saved on the hard disk of the digital receiver To enable this feature select the System Set ting menu and set the Time Shifting option to Enable For de tailed descriptions about the time shift function refer to 5 4 3 7 Setting for MediaHighway EPG Almost every service provider would provide electronic pro gram guide containing detailed program information You can get more abundant program information from a dedicated transponder providing only electronic program guides than general service providers MediaHighway refers to the ded 28 Preference Settings icated transponder For detailed descriptions about the elec tronic program guide refer to 5 2 To set a dedicated electronic program guide transponder se lect the System Setting gt Medi Satel te Nar IA a E p me aHighway EPG menu MediaHighway EPG Moves Item 4h Selects Item WERU Previo To use a dedicated electronic program guide transponder set the MediaHighway option to On And then set the Satellite Name and Home Transponder options to available ones and set the Tuner Select option to a tuner through which to receive them 29 Chapter 4 Service Search You have to perform service search after connecting the digital receiver 4 1 Searching satellite broadcasting services This digital receiver can be operated with both fixed and mo torized antenna system You have to configu
37. folder To move a file to another folder put the highlight bar on a file entry you want and press button Then a folder list ap pears Once you choose a folder in the list the file gets moved to that folder To delete a file To delete a file put the highlight bar on a file entry you want and press 04 button Then a confirmation box appears The selected file will be deleted with the Yes reply To sort file entries To sort file entries perform the following steps 1 Put the highlight bar on a file entry you want 2 Press button to display an option list 3 Set the Sorting option to Alphabetic Time or Size as you want 4 Press the button 5 The file entries are sorted by the option specified To rename a file To rename a file perform the following steps 1 Put the highlight bar on a file entry you want 2 Press button to display an option list 3 Select the Rename menu to display an on screen key board 4 Enter and save a file name as you want with the key board For how to use the keyboard refer to 8 6 2 5 The file is renamed as specified You can rename a folder in the same manner 7 3 Playing back a recording 65 To lock a recording file To lock a file perform the following steps Put the highlight bar on a file entry you want Press button to display an option list To lock the file set the Lock option to Locked To unlock the file set the Lock option to Unlocke
38. gital re ceiver and the television you need to connect the digital re ceiver to your television antenna so that it can receive digital television services Connect a cable from your satellite antenna to the LNB IN connector on the back panel of the digital receiver and connect a cable from your terrestrial antenna to the ANT connec tor 2 4 2 Connecting to your television Among the following connectors on your digital receiver you should use the first connector to get best video quality If your television does not have the matching connector then use the next connector 1 SCART connector TV 2 S Video connector S VIDEO 3 Composite connector VIDEO 4 RF connector RF OUT You should configure audio and video settings after connect ing See 3 2 for detailed description 14 Setup To use the SCART connector TT Ne A KN For best results with a standard television set you should use a SCART cable plugging one end into the TV socket on the digital re ceiver and the other end into a free SCART socket on your television Some televisions have inputs via Component or S Video con nectors rather than SCART If you have such a television use an appropriate conversion cable to link the TV socket on the digital receiver to the matching socket on your television If you connect with a standard SCART cable you do not have to make audio connections because the SCART connector can output st
39. he digital receiver select the Instal lation gt Format Hard Disk menu Formatting the hard disk will delete all files permanently If a new hard disk drive is installed it must be formatted because the file system of the digital receiver is different from any of the personal computer You cannot use time shift and record functions with an unformatted hard disk 7 7 Transferring recording files Itis possible to transfer recording files from the digital receiver to your computer via a USB cable The file transfer program Altair is needed here which is available at the Topfield web site http www i topfield com The method is as follows 1 Download Altair from the Topfield web site N Plug one end of a USB cable into the USB port on the digital receiver and the other end into the matching port on your com puter 3 Turn on the digital receiver 4 Run Altair 7 7 Transferring recording files 73 Fer Of ations C4 6 86 GE Froe 19 53 GB Total Size Type Date Size Typ Folder Folder 39KB Win Queen Want To Brea 4 138KB Win Z Queen Killor Quesn mp 13KB BIN Queen Love of my life 5 882K8 Win Z Queen Somebody To 323KB Win 2 Queen Love of My Lit 4 318KB Win 2 Queen Too much love 1 073 KB 6 314 KB i amp KB BIN 378 Win 6 365KB Win 1 073 KB 6 314 KB 8 a 969KB JPE KB BIN 5 046KB Win PTOS Ta AP 13KB Ado BD tan and samples_20 BJune0
40. he first ser vice search after connecting the digital receiver The digital re ceiver will search all available services with automatic search mode Transponder numbers range from 5 to 12 at VHF and 21 to 69 at UHF To search a certain transponder set the Search Mode option to Manual and select your desired transponder at the Channel option You can search pay services as well as free services To search only free services set the FTA Scrambled option to FTA only FTA means free service To search only pay services set it to CAS only CAS means pay service To search both free services and pay services set it to FTA CAS To start service search select the Service Search command Then appears a list box in which found services will be listed Press the button to save found services when a service search has been completed To stop service search on the way 38 Service Search or exit without saving press the button 4 3 Copying services The digital receiver maintains separate service list with each tuner If a certain service is registered on only one tuner s ser vice list It may be impossible to watch a service and record two other services You can copy entries of one tuner s ser vice list to the other tuner s service list to avoid such inconve nience To copy service entries select the Installation gt Services Copy menu There are three copy commands To copy service en tries of the first tuner to the sec
41. he module and subscription Slot 4 Not Installed card inserted to the digital re ceiver select the Common Inter face menu 2 1 Unpacking Chapter 2 Setup Before going any further check that you have received the fol lowing items with your digital receiver Remote control unit Two batteries for the remote control AAA 1 5 V One Component AV cable to link the digital receiver to your television set One S Video cable to link the digital receiver to your television set A copy of this user guide 2 2 Safety precautions Please read and keep the following safety precautions care fully The power must be 90 to 250 volt Check it before con necting the digital receiver to the wall outlet For the 10 Setup power consumption of the digital receiver refer to Ta ble 2 1 The wall outlet shall be installed near the equipment and shall be easily accessible Do not expose the digital receiver to any moisture The digital receiver is designed for use in dry rooms If you do use it outdoors ensure that it is protected from mois ture such as rain or splashing water Use only dry cloth when cleaning the digital receiver Place the digital receiver on a hard and level surface Do not place the digital receiver close to heating units or in direct sunlight as this will impair cooling Do not lay any objects such as magazines on the digital receiver When placed in a cabinet make sure there is a minimum
42. he position then the pointer starts to blink 5 Find the other end position 6 Press Y button at the position again then a confirma tion box appears 7 Select the Cut command then the block is erased 70 Recording and Playing 7 4 2 To store a block from a recording You can store a block from a recording file by performing the following steps 1 2 3 Start playback of a recording file you want Press button to display a progress bar Find one end position of a block you want to specify with button or button Press 4 button at the position then the pointer starts to blink Find the other end position Press button at the position again then a confirma tion box appears Select the Save command then the block is stored The stored file will named after its source file with a suffix of CUT and a number In addition you can copy a recording file in whole or in part when playing back it 1 2 Start playback of a recording file you want Find a desired position from which a copy will be started with E button or ED button Press button Pressing O button stops copying The copied file will be named after its source file with a suffix of COPY and a number Once a copy is started a copying symbol like the next figure will be displayed on the right top of the screen for a few seconds To see copying status press Ed button The outer circle of
43. ices with a PAL television and to watch NTSC services with a NTSC television How ever the multi television set is able to process both of them So if you have an multi television set set the TV Type op tion to Multi With this option the digital receiver will output them without standard conversion This setting is most rec ommended especially if you are not sure what standard tele vision you have 3 2 2 Color model Through the TV SCART connector the digital receiver is able to output video in various color models If you have the digi 3 2 Video and audio settings 21 tal receiver linked to your television from this connector you should set the Video Output option to your desired color model If you have connected them by RCA connector at which VIDEO reads on the back panel of the digital receiver you do not have to set this option because the digital receiver outputs CVBS video through RCA connector independent of SCART connec tor However If you have connected them by S VIDEO connec tor you have to set this option to S Video because the output through S Video connector comes from the SCART interface It is known in general that the RGB color model provides the best video quality with little difference from the YUV color model but the CVBS color model does the least So RGB would be most desirable for this option 3 2 3 Video cassette recorder You would have the digital receiver linked to your video cas sette
44. ich has only two inputs you should set the DiSEqC 1 0 option to Mini A in stead of 1 of 4 Al A2 A3 A4 AS AG A7 A8 A9 A0 DiSEqC 1 1 Switch L 4 1 2 Configuring DiSEqC 1 2 settings Your motorized antenna will turn toward your desired satel lites horizontally by DiSEqC 1 2 32 Service Search When you switch to an service if the service is provided by a satellite other than current one it will take longer time than usual because the antenna has to turn to its position To use DiSEqC 1 2 select the In stallation gt Satellite Setting gt or Asiasat2 C Motorized DiSEqC 1 2 menu EE At first you have to set the Mo Motorized DISEQC 1 2 psc Command wade ma Cifotor contre Disable torized DiSEqC 1 2 option to Enable Service Search To get the correct position of your desired satellite perform the following steps 1 Choose your desired satellite at the Satellite Name op tion Set the DISEqC Command Mode to User Select the Goto command at the Motor Control menu Then the antenna will turn toward your selected satel lite with the position data that the digital receiver has If the receiving quality which is displayed on the right bottom on the screen is not good tune the antenna finely with the commands of the Movement menu If you select the 2 E movement command the antenna will move to the east by two degrees
45. irmware 9 1 From a broadcaster 77 update 9 1 From a broadcaster You can get a new firmware from a broadcaster over the air To update the firmware by this method press the Installation gt Firmware Upgrade menu a Selecting the Start command starts firmware update On the left table is presented the transponder information appointed by the manufac turer Topfield for firmware Satellite Astra Frequency 12603 MHz Symbol Rate 22000 KS s Polarity Horizontal PID 347 update This transponder information can be changed You can get the information at the Topfield web site http www i topfield com 9 2 From your computer via USB port You can transfer a new firmware to the digital receiver from your computer connecting them with a USB cable You need TFDN_USB the firmware transfer utility for this which is avail able at the Topfield web site http www i topfield com 78 Firmware Update To update the firmware with this method perform the follow ing steps 1 Download a new firmware applicable to the digital receiver from the Topfield web site 2 Plug one end of a USB cable into the USB rez port on the digital receiver and the other end into the matching port on your com puter 3 Turn on the digital receiver 4 Run TFDN_USB How to use TFDN_USB is as follows lt 2 TFD USB DOWNLOAD 1 Press the Find button to select the FileName D MyTaski TopfieldUpdateli Tt n
46. iver 74 Correct disposal of this product This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life ES To prevent possible harm to the environment or human health from uncon trolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can dispose this product for environmentally safe recycling Business users should contact their supplier and check the terms and condi tions of the purchase contract This product should not be mixed with other commercial wastes for disposal Topfield continues to improve the digital receiver which this guide explains So some ex planations and illustrations in this guide could be different from the real digital receiver Copyright O 2006 Topfield Co Ltd English version http www i topfield com 110T F9115 201 0 Rev 1
47. iver from another same digital receiver connecting them with a RS 232 cable To update the firmware with this method perform the follow ing steps 80 Firmware Update a 1 Plug one end of a RS 232 cable 9 pin D sub cable into the RS 232 port on the digital receiver and the other end into the matching port on the other digital re ceiver 2 Turn on both of them 3 Select the Installation gt Transfer Firmware gt Transfer Firmware to Other IRD menu 81 16 9 21 16 9 Display Format 22 1st Audio Language 19 1st Subtitle Language 19 22 kHz 31 2nd Audio Language 19 2nd Subtitle Language 19 4 3 22 A V Output Setting 20 Access Control 26 Add to FAV 41 Advanced 35 After next program 57 After this program 57 ALL 38 Alphabetic 41 51 64 Altair 72 73 ANT 11 13 Antenna Supply 5V 37 Astra 77 AUDIO L 15 AUDIO L R 12 AUDIO R 15 Auto 35 37 Auto Start 75 Index Button 5 C band 29 CAM 8 CAS 36 37 CAS only 36 37 CAS FTA 41 51 Censorship 26 Center Extract 22 Change PIN Code 26 Channel 37 CI 8 Common Interface 8 Current Event 58 Cut 69 Date 60 Default 41 51 Delete 40 50 Diab 74 DiSEqC 31 DiSEqC 1 0 31 DiSEqC 1 1 31 DiSEqC Command Mode 32 Download 78 79 Duration 56 60 DVB 1 82 INDEX Electronic Program Guide 44 Electronic program guide 2 Every Day 60 Every Weekday 60 Every Weekend 60 Fa
48. l lows e It supports DiSEqC 1 0 DiSEqC 1 1 DiSEqC 1 2 and US ALS 2 Introduction It is able to memorize up to 5000 television and radio services Electronic program guide provides an overview of pro gram schedules for next few hours You can edit the service list You can make your favorite list You can view the information of the current television or radio program You can update the firmware of the digital receiver to the latest which will be provided by the manufacturer The digital receiver features a digital video recorder with two tuners with which you can record your choice of broadcasting services independently of ones you are cur rently watching The large storage capacity of the built in hard disk al lows you to record up to 40 hours of material in case of 80 gigabytes in excellent picture and sound quality Time shift is a special technical feature You can pause the program you are watching and resume it again at a later time You can quickly find whatever part of the current program by backward or forward search 1 2 Controlling the digital receiver You can control the digital receiver with the remote control and the buttons on the front panel NOTE When the digital receiver is off but plugged to a wall outlet we say that it is in standby mode on the other hand when it is on it is in operation mode You should keep the digital 1 2 Controlling the digital receiver 3 1 2 1
49. lace the highlight bar on a file entry you want to run 3 Press the button to start the program 4 To exit the program press the button The figure on the left is a run ning screen of a TAP Image Viewer which displays image files of BMP GIF and JPG for mat This TAP is available from the Topfieldweb site http www i topfield com In the program file list you can use a variety of file control functions including renaming sorting deleting and so on For detailed descriptions about file control functions refer to 7 2 If you want a program to run automatically when the digital receiver starts up move the program to the Auto Start folder Press the 0 button at start up if you want the program not to run 76 Firmware Update Chapter 9 Firmware Update The digital receiver has a stable and convenient firmware to use However a new firmware may be released to improve the digital receiver You can get a latest firmware and an update utility from the Topfield web site http www i topfield com You should check the firmware information of your digital re 60000 ceiver before downloading a i A mg 4 new firmware To check the cur Application Version TF MCMFI 1 00 11 f rent information of the digital receiver select the Information gt IRD Status menu NOTE You have to update with only the new firmware of which Sys tem ID is identical to yours otherwise you will fail in f
50. lite Name op tion 2 Set the Search Mode option to Auto To search every service of a transponder perform the follow ing steps 1 Choose your desired satellite at the Satellite Name op tion 2 Set the Search Mode option to Manual 3 Choose your desired transponder at the Frequency op tion or input it with the numeric buttons 4 Input the symbol rate of your desired transponder to the Symbol Rate option with the numeric buttons 5 Set the Polarization option to the polarization of your de sired transponder NOTE You could get the transponder information from a satellite magazine or web site such as http www satcodx com To search one service of a transponder perform the following steps 1 Choose your desired satellite at the Satellite Name op tion 2 Set the Search Mode option to Advanced 3 Choose your desired transponder at the Frequency op tion or input it with the numeric buttons 4 Input the symbol rate of your desired transponder to the Symbol Rate option with the numeric buttons 5 Set the Polarization option to the polarization of your de sired transponder 36 Service Search 6 Specify the PIDs of your desired service at the PID menu with the numeric buttons PID Packet Identifier is a set of numbers that identifies transport stream packets To search every service of a SMATV transponder if the digi tal receiver is connected to a SMATV perform the following steps 1 Choo
51. nge symbol rate po larization and LNB frequency corresponding to the frequency range So you might not have to specify the LNB Frequency option However if you have selected the Other entry at the Satellite Name option to specify a satellite that is not in the 4 1 Searching satellite broadcasting services 31 satellite list you might have to make out the correct LNB fre quency The difference between a broadcasting frequency and its LNB frequency must be within 950 to 2150 MHz For exam ple if the frequency band of your desired satellite ranges from 3660 to 4118 MHz you have to set the LNB Frequency option to 5150 MHz The LNB has to be supplied with power to operate Set the LNB Power option to On if it does not have any other power supply You had better ignore the 22 kHz option The digital receiver is designed to be compatible with DiSEqC Digital Satellite Equipment Control switches It is possible to connect several antennas to one digital receiver by DiSEqC switches A DiSEqC 1 0 switch allows switching between up to 4 satellite sources and a DiSEqc 1 1 switch allows switching between up to 16 satellite sources Set the DiSEqC 1 0 and DiSEqC 1 1 options according to your antenna configuration en For example to select the antenna con LNB IN nected to the A5 input in the left fig ure set the DiSEqC 1 1 option to 2 of 4 and the DiSEqC 1 0 option to 1 of 4 If you have a mini DiSEqC 1 0 switch oca a wh
52. on once more displays detailed information about the current program To hide the information box press the button 5 1 3 Selecting audio track Some programs are provided with audio tacks of one or more languages Pressing the button displays available audio tracks Once you select one among them it will be sounded In addition you could enjoy audio tracks in one of four sound modes Stereo Mono Left or Right However if multifeed service is available at the moment multifeed services will be displayed In this case you have to press Q button once more to select an audio track 5 14 Selecting subtitle track Some programs are provided with subtitle tracks of one or more languages If the current program provides subtitle tracks the subtitle symbol will be marked on the information box Pressing the g button displays available subtitle tracks Once you select one among them it will be displayed 44 Daily Usage 5 15 Viewing teletext With some programs such profitable information as weather reports news or stock quotations is provided by means of tele text service If the current program provides teletext service the teletext symbol will be marked on the information box Press the button to view teletext pages You can zoom in the teletext with the yellow button and adjust its transparency with the blue button To clear the teletext screen press the button 5 2 Viewing elec
53. ond tuner s service list select the Tuner 1 to Tuner 2 command To copy on the contrary select the Tuner 2 to Tuner 1 command To copy reciprocally select the ALL command 4 4 Resetting to factory settings The digital receiver maintains the following data e Satellite list e Service list e Favorite list e Timer list e Preference settings You can reset all data of the digital receiver To reset all the data select the Installation gt Factory Setting menu then you will be asked for confirmation With the Yes reply service en tries favorite entries and timer events will be all deleted and preference options will be reset to the manufacturer s factory settings 39 Chapter 5 Daily Usage 5 1 Watching television To switch services press the or button Pressing Y button switches to the previously viewed service You can switch to your desired service by entering its service num ber with the numeric buttons You can also select a service to watch in the service list To see the service list press the button The service list enumerates the following items 4 Real Madrid TV 3 SATLINK A _ Service number 48 CHT ul gt Hongyup e Service name DIGITAL e Transmitting satellite Transponder orsat 12066 1 3700 Help A dollar mark may be marked on some entries which means pay service To watch a pay service you need its sub scription card 40 Daily Usage To
54. option to Letter Box Wide screen pictures then will be reduced to fit to the width of the normal screen Otherwise to watch them in the shape like the right figure set the option to Center Extract Wide screen pic tures then will be cut out on the left and right sides equally to fit to the width of the normal screen 3 2 5 Sound mode Basically there are two audio sources as you can find two au dio sockets on the back panel of the digital receiver You can 3 3 Local time setting 23 enjoy only one source or both of them in either stereo or mono Set the Sound Mode option as you desire Apart from this setting you can change the sound mode with button See 5 1 3 for detailed description 3 2 6 RF output If you have connected your television to the RF OUT socket you should configure the radio frequency output The digital receiver can make the analog television from the digital tele vision and output it through the RF OUT socket Set the RF Output option to the television standard that your country supports referring to Table 3 1 Table 3 1 Television standards by country Signal type Country 3 3 PAL G PAL PAL K NTSC M Australia Austria Cyprus Czech Republic Egypt Estonia Finland Ger many Greece Iceland Iran Israel Italy Kuwait Latvia Libya Lithuania Luxembourg Netherlands New Zealand Norway Portugal Slovakia Slove nia Spain Sweden Switzerland Syria Yugoslavia Hong
55. position press Y button or ED button unceasingly until you find it e To see the current playback position press UY button to display a progress bar To hide the progress bar press again You can specify a playback position entering percent with the numeric buttons when the progress bar is hidden 7 3 1 To play back in slow motion To play back in slow motion press button on playback Whenever pressing button playback speed changes in 3 steps 7 1 and i times speed To return to normal speed press EY button 7 3 2 To play back in fast motion To play back in fast motion press button on playback Whenever pressing E button playback speed changes in 3 steps 2 4 and 6 times speed To return to normal speed press O button 7 3 Playing back a recording 67 The digital receiver can play back not only forward but also backward in fast motion To play back backward in fast mo tion press E button Whenever pressing button play back speed changes in 3 steps 1 2 and 3 times speed To turn to forward playback press EY button 7 3 3 To play back recordings in sequence The digital receiver can play back several recording files in sequence To use this utility perform the following steps 1 2 Press button to display the recording file list Select file entries you want to play back by pressing Y button When a file entry is selected it is numbered Press the Ok button to start playb
56. r entry put the highlight bar on the entry you want and press the button To edit a timer entry put the highlight bar on the entry you want and press button then the timer edit box appears in which you can change its timer settings 7 1 Recording a program 61 7 14 Recording by electronic program guide 65 16 00 10 30 16 30 17 00 17 00 17 30 17 30 18 00 18 00 19 30 JOURNAL MADE IN GERMANY JOURNAL EUROMAXX If an electronic program guide is properly provided on the ser vice you wish to record you can wona ar soccen gt set a timer recording in it by per forming the following steps Select a service you want to record Press the button to display its electronic program guide Select a program you want to record Pressed the button one time P is marked up on the program entry pressed once more R is marked up The former indi cates turn on the latter indicates record on This timer recording is put on the timer list To edit this timer recording press O button then a timer edit box appears in which you can change its timer settings To remove the marking press the OK button once again 7 15 Recording when using time shift While you are watching a program by time shift function you can record the program by performing the following steps k 2 Press EY button to start time shift To find a desired recording position press QJ button or
57. re antenna set tings according to your antenna system in the following order 1 Configure LNB settings Refer to 4 1 1 2 Set the position of your desired satellites if you have a motorized antenna You can control the antenna in DiS EqC 1 2 mode or USALS mode Refer DiSEqC 1 2 to 4 1 2 and refer USALS to 4 1 3 3 Perform service search 4 1 1 Configuring LNB settings There are in large two frequency bands for satellite broadcasts One is C band which ranges approximately from 4 to 6 GHz 30 Service Search The other is K band which ranges approximately from 12 to 18 GHz The LNB Low Noise Block converter is used to take a wide band of rel atively high frequencies amplify and convert them to similar signals carried at a much lower frequency which is called IF Intermediate Frequency High frequencies from satellites are converted into from 950 to 2150 MHz by a LNB Select the Installation gt Satellite Setting gt LNB Setting menu to 0 Asiasat2 C configure the LNB settings 5150 MHz a On on Disable ios dish m MINU Previous Menu Pressing the OK button on the Satellite Name option displays the satellite list in alphabetic order Select the satellite toward which your antenna sets its face The digital receiver has a database about broadcasting satel lites and their transponders containing the following infor mation satellite position frequency ra
58. receiver 16 Setup In this case you will need to connect a ca ble from the RF OUT socket to the antenna connector on your television To ensure your television can also pick up existing analogue channels as well you will need to connect a cable from your television antenna or from the RF LOOP OUT connector on the back of the digital receiver to RF IN connector 2 4 3 Connecting to your video cassette recorder The digital receiver also can output video to another appliance such as video cassette recorder or video receiver through an auxiliary SCART connector ISS A You should prepare a SCART cable to use the auxiliary SCART connector Plug one end of the cable into the VCR socket on the digital receiver and the other end into the match ing socket on your video cassette recorder or suchlike 2 5 Inserting batteries in the remote control To insert the batteries open the battery compartment by re moving the lid and then insert the batteries observing the po larity which is marked on the base of the battery compart ment If the digital receiver no longer reacts properly to remote con trol commands the batteries may be flat Be sure to remove used batteries The manufacturer accepts no liability for dam age resulting from leaking batteries NOTE 2 5 Inserting batteries in the remote control 17 Batteries including those which contain no heavy metals may not be disposed of with household wa
59. s or O button unceasingly until itis found Pressing the button reverses the program to 10 sec onds back To end time shift display the progress bar with O but ton and press O button 5 5 Watching by picture in picture 47 5 5 Watching by picture in picture You can watch two services at the same time one of which is shown in a subpicture We call this picture in picture A INTERNATIONAL How to use the picture in picture function is as follows 1 Press the button to display a subpicture in which an other service will be shown Pressing the button once more minifies the subpic ture and pressing it once again hides the subpicture Pressing the button interchanges the main picture with the subpicture Even when you play back a record ing you can watch a live service in subpicture How ever the picture interchange will not work in that case Pressing button moves the subpicture counterclock wise and pressing button moves it clockwise To display a service list for the subpicture press 04 but ton If both are pay services all the only main picture will be shown NOTE 48 Daily Usage If you wish to watch two pay services by picture in picture you should prepare a dedicated CAM that is able to descram ble two pay services simultaneously 49 Chapter 6 Listing Services 6 1 Editing the service list You would have got a service list
60. s named after its service name with a suffix of a number To display the recording file list press button For detailed description about the recording file list refer to 8 7 2 58 Recording and Playing 7 1 2 Recording by the recording menu To record a program by the Recording recording menu select the Recording menu Service 54 P Cine04 8 ne ry File Name P Cine04 Record Start No Recording Timer Setting 150384 MB Free Select the start time to record Moves item P Selects Item WENU Exit You can record two services at the same time Set the Record No option to distinguish two records Set the Satellite option to the satellite which transmits the ser vice you want to record Pressing the button on this op tion displays a satellite list in which you can select your de sired satellite Set the Service option to the service which provides the pro gram you want Pressing the button on this option dis plays a service list in which you can select a desired service There are two recording start modes To start recording im mediately set the Start Time option to Quick If you are using time shift function and so you wish to record even the contents in the time shift buffer set this option to Current Event Set the Duration option to a time after which your recording will be finished The allowable maximum value is 23 hours and 55 minutes Pressing on the File Name option displays an on screen ke
61. se your desired satellite at the Satellite Name op tion 2 Set the Search Mode option to SMATV 3 Choose your desired transponder at the Frequency op tion or input it with the numeric buttons 4 Input the symbol rate of your desired transponder to the Symbol Rate option with the numeric buttons 5 Set the Polarization option to the polarization of your de sired transponder You can search pay services as well as free services To search only free services set the FTA Scrambled option to FTA only FTA means free service To search only pay services set it to CAS only CAS means pay service To search both free services and pay services set it to FTA CAS To start service search select the Service Search command Then appears a list box in which found services will be listed Press the button to save found services when a service search has been completed To stop service search on the way or exit without saving press the button 4 2 Searching terrestrial broadcasting services 37 4 2 Searching terrestrial broadcasting services To perform service search se lect the Installation gt Terrestrial Search menu Start Seal 08 Level 00 Quality If you have an active antenna you should set the Antenna Supply 5V option to on to supply power to the amplifier of your antenna The digital receiver will supply the antenna with 100 milliampere at maximum You should set the Search Mode option to Auto at t
62. select your desired service put the highlight bar on its en try with the or button and press the button Then your selected service will be shown Pressing the or button skips over 10 entries up or down Entering a service number with the numeric buttons puts the highlight bar on its entry Pressing the button performs an alphabetic browse For instance when the highlight bar is on an entry of which initial is B pressing the button puts the highlight bar on the first entry of which initial is C To sort the service list by service name press the button Pressing this button once more makes it sorted by service num ber In addition pressing the button displays an dialog box in which you can do the followings Select your desired satellite with the Satellite option then the only services provided by the selected satellite will be listed e Select your desired tuner with the Tuner option then the only services provided through the selected tuner will be listed e To browse service entries grouped by service provider set the Show Provider option to On You may regard a service provider as a transponder To rename the current service entry select the Rename command then a keyboard appears with which you can enter a name e To prevent other family from watching the current ser vice entry set the Lock option to Locked You have to enter PIN code when to watch or unlock a locked ser vice e To delete the
63. socket for the television set 12 Setup AUDIO L R S VIDEO TV O VCR 49 RF IN RF OUT 2 S PDIF USB RS 232 Stereo audio output socket for the tele vision set or audio system Super video output socket for the televi sion set Audio and video output socket for the television set Audio and video input output socket for the video cassette recorder or such like Analog television input socket Analog television output socket Dolby digital output socket for the au dio system USB port for firmware update and data transfer Serial port for firmware update and data transfer Table 2 3 Connectors specification VIDEO Composite video CVBS output AUDIO Left amp right audio output S VIDEO Super video S Video output TV CVBS S Video RGB YUV video output Left amp right audio output VCR CVBS video output Left amp right audio output CVBS S Video RGB YUV video input for bypass Left amp right audio input for bypass S PDIF Dolby digital audio output RS 232 115 2 kbps at maximum USB 2 0 2 4 Connecting up your digital receiver 13 2 4 Connecting up your digital receiver There are several ways to set up the digital receiver Set up the digital receiver suitably to your television and other ap pliances If you have any problem with your setup or need a help contact your dealer 2 4 1 Connecting to the antenna Whatever sort of connection you have between the di
64. ste Please dispose of used batteries in an environmentally sound manner Find out about the legal regulations which apply in your area 18 Preference Settings Chapter 3 Preference Settings 3 1 Language settings You can designate languages for menus audio tracks and sub title tracks Select the System Setting gt Language Setting menu Changes the Menu language Moves item 4 Selects Item WENU Previous Menu Menu language The digital receiver supports a lot of menu languages Ara bic Dutch English German French Italian Russian Turkish and so forth Set the Menu Language option to your desired 3 2 Video and audio settings 19 Subtitle language Audio language language Once you select a language the menu will be im mediately displayed in the selected language Set the 1st Subtitle Language and 2nd Subtitle Language op tions to your desired languages When you watch a program if the program has the subtitle track of the langauge desig nated at the 1st Subtitle Language it will be displayed If the first laguage is not available but the second language is avail able the second language s subtitle will be displayed If there is not any available language no subtitle will be displayed Apart from this setting you can select a subtitle track with the g button See 5 1 4 for detailed description Set the 1st Audio Language and 2nd Audio Language options to your desired languages
65. to select another group Whenever pressing the button the highlight bar of each column becomes movable in turn You can add groups up to 30 To add a group select the NEW command in the group list then a on screen keyboard ap pears You can move the highlight key horizontally with the and buttons and vertically with the P and P buttons Pressing the button on a key enters the corresponding letter in the input line 6 3 Transferring receiver data 53 To type lower case letters or numerals select the Other key To delete a letter put the cursor on a desired letter in the input line and select the Del key You must select the Save key to complete naming Otherwise if you press the button it will not be named To rename a group put the highlight bar on a desired group entry to rename and press the button then the on screen keyboard will appear likewise To delete a group put the highlight bar on a desired group entry to delete and press the button then a confirmation box appears The selected group will be deleted with the Yes reply Similarly you can delete a favorite entry with the button in the favorite list Besides you can rearrange a group s fa vorites by moving a favorite entry To move a favorite entry put the highlight bar on a desired entry to move and press the ca button then the selected entry becomes dark Move it to a desired place and press the button To add radio services press
66. trol menu displays a list of menus that you can lock If the Time Setting item is set to Locked you have to enter the per sonal identification number to access the Time Setting menu If you enter a wrong number you cannot use the menu To release a shut item set it to Unlocked 3 5 Adjusting on screen display 27 3 5 Adjusting on screen display You can adjust the transparency level of on screen display Se lect the System Setting menu and set the OSD Transparency option as you desire Its available range is 0 to 50 percent You can adjust the display time of the information box Refer the information box to 5 1 2 To adjust its display time select the System Setting menu and set the Info Box Display Time option as you desire Its available range is 1 to 30 seconds If you set this option to No Info Box the information box will not displayed when you switch services However pressing the button displays the information box If you set this option to Never Hide the information box will always be displayed You can raise or lower the position of the information box Se lect the System Setting menu and then set the Info Box Posi tion option as you desire Its available range is 10 to 3 line The more high the value is set the more low the information box will be positioned 3 6 To use the time shift feature You can use the time shift feature with this digital receiver Time shift just means that the most recent hour o
67. tronic program guide 65 The Electronic Program Guide shows the current and sched uled programs that are or will be available on each service with a short summary for each program Pressing the button dis plays the electronic program guide in which you can see the ene OF SOCCER following things 16 00 16 30 JOURNAL 16 30 17 00 MADE IN GERMANY 17 00 17 30 JOURNAL 17 30 18 00 EUROMAXX 10 00 10 30 To OK Re 0 Scheduled programs e Program commentary e Broadcasting date Broadcasting time Noxt Info Page To see detailed information of a desired program entry put the highlight bar on your choice with the or button and press button To switch to an other service press the or button To see a program guide for radio broadcasts press the but ton To turn it back press the button again Pressing the button displays the program guide for each 5 3 Watching multifeed program 45 service To turn it back press the button again You can make a timer recording by the electronic program guide for which refer to 8 7 1 4 5 3 Watching multifeed program Some pay broadcasts such as sports channels would provide a variety of perspectives on a program at the same time You can select and watch a perspective you prefer among them This is called multifeed service In similar method they can also provide multiple copies of a program at short time int
68. will be shown Oth erwise to select another group press the button then the highlight bar of the group list becomes movable E ETET then the highlight bar of the Sports If you switch to another service after you have selected a fa vorite service it will be also another favorite service of the se lected group The digital receiver will remind you what group you have selected displaying its name on the right top of the screen whenever you switch to another service If you wish you can select all services select the All services entry in the favorite list For how to edit the favorite list refer to 8 6 2 5 1 2 Viewing program information Pressing button displays the information box in which you can verify the followings e Service number e Service name e Transmitting satellite e Receiving tuner e Transponder information e Signal level and quality e Program name e Program rating e Program commentary e Broadcasting time e Current time 5 1 Watching television 43 In addition you might see the following symbols e Subtitle symbol if subtitles are provided on the cur rent program e Teletext symbol if teletext is provided on the current program e Lock symbol o if the current service is locked e Dollar symbol if the current service is a pay service e Multifeed symbol CA if the current program is pro vided in multifeed service Pressing EU butt
69. yboard with which you can specify a file name for your timer recording If you do not specify anything it will be named after its service name For how to use the keyboard refer to 6 2 7 1 Recording a program 59 To start recording select the Record Start then the Stop com mand gets enabled You can select that command to stop the recording 7 13 Making a timer recording You can make a program to be recorded at a specific time Even If the digital receiver is off it will be turned on and start recording at a time specified The digital receiver will be turned off again as the recording ends To make a timer recording se lect the System Setting gt Timer Setting menu then a timer list appears Type Tuner Select gt Satellite Service Ok 54 P Cine04 Mode 4 One Time Date 4 01101 2004 Thu Start Time 04 15 Duration 30 Min File Name or OK Next Prev entry OR Edit en Insert To add a new timer entry press the button and then a timer edit box appears You have to set the Record option to On to record a program If this option is set to Off the digital receiver will be turned on at a specified time but not record instead you may record a program with your video recorder in this case If you want to record a radio program set the Type option to Radio Otherwise set to TV If you record a satellite program set the Tuner Select option to Satellite otherwise set it to Terrestrial

Download Pdf Manuals

Related Search

Related Contents

Gay - Lussac École maternelle    File  Travis.  Response 110 user guide  JIS S 0025  Kabiloo BLUE BEAT M100  Wiley Beginning Ajax with ASP.NET  Conceptronic Wireless 54Mbps 11g PC Card  User and maintenance manual Manuale d`uso e manutenzione  

Copyright © All rights reserved. Failed to retrieve file