Home

Tannoy G0512 Speaker User Manual

image

Contents

1. Thank you for selecting Tannoy loudspeakers developed in the UK by our dedicated team of design engineers they are the choice of discriminating music lovers the world over Musical excellence is designed into our loudspeakers from the start Careful selection of the very best components combined with strict quality control procedures in the production process ensures this level of excellence is maintained To gain maximum performance from your loudspeakers please take time to read this owner s manual in full before installation Once you have set up your new loudspeakers please complete and return the registration document this does not limit your legal rights Loudspeakers are electromechanical devices that run in through use performance will therefore improve after an initial period of 24hrs use Once they have been further run in over a longer period there will be clear enhancement of the stereo imaging mid band quality and bass performance characteristics We are confident that you will continue to enjoy your new Tannoy loudspeakers for many years to come AMPLIFIER MATCHING Consult the enclosed product specification sheet as this clearly shows the acceptable power range for amplifier matching to your speakers The high peak power handling of Tannoy loudspeakers permits responsible use with more powerful amplifiers please read the Warranty As with all loudspeaker systems the power handling is a function of voice coil thermal ca
2. no absolute right or wrong here therefore much will depend on your own musical preferences Hace RODOS ETA POSITIONING Begin by angling the speakers towards your chosen listening position usually this is on the centre line of the room so that when seated you can just see the inner side panel of each speaker The front of the loudspeaker should not be obstructed in any way The loudspeakers should be located between 1 5 to 4 5 metres 5ft to 15ft apart with the listening position set slightly further away than the speakers are apart All models are fully shielded to eliminate colour fringing effects when placed close to televisions Avoid positioning the loudspeakers in corners of the room as this will have a negative effect on performance maintain a distance of at least 0 5 metres 20 inches from the rear wall and 1 metre 39 inches from the side See figure 3 BI WIRING Where the facility to bi wire your loudspeakers is provided we would strongly recommend that you install your system using this wiring option With this method you will require separate cable feeds from your amplifier to the HF and LF units of each loudspeaker Generally this will result in a significant improvement in resolution transparency stereo focus and instrument separation Use a high quality bi wire cable to connect the speakers to the amplifier It is recommended that the same cable length and type be used for both bass and treble It is essent
3. the surface TANNOY TECHNICAL SPECIFICATIONS PERFORMANCE Recommended amplifier power Watts RMS Continuous power handling Watts Peak Peak power handling Watts Sensitivity 2 83 Volts 1m Nominal Impedance Ohms High frequency Low frequency alignment 6dB Frequency response 3dB DRIVE UNIT CONFIGURATION Mercury F1 Mercury F2 Mercury F3 10 70 10 85 10 100 50 60 70 100 120 140 87dB 88dB 89dB 8 8 8 55Hz 48Hz 32Hz 55Hz 20kHz 48Hz 20kHz 35Hz 20kHz 25mm 1 25mm 1 25mm 1 Nitro urethane Nitro urethane Nitro urethane layer dampened layer dampened layer dampened woven polyester woven polyester woven polyester Mercury F4 Mercury FR Mercury FC 10 140 10 60 10 90 100 40 70 200 80 140 91dB 86dB 90dB 8 8 8 35Hz 59Hz 68Hz 35Hz 20kHz 59Hz 20kHz 68Hz 20kHz 25mm 1 25mm 1 25mm 1 Nitro urethane Nitro urethane Nitro urethane layer dampened layer dampened layer dampened woven polyester woven polyester woven polyester SET UP DIAGRAMS FIG 1 iE 4 font d m tes A dome dome dome dome dome dome neodymium neodymium neodymium neodymium neodymium neodymium shielded magnet shielded magnet shielded magnet shielded magnet shielded magnet shielded magnet assembly assembly assembly assembly assembly assembly Low frequency 130mm 5 165mm 6 5 165mm 6 5 2x 165mm 6 5 100mm 4 2x 100mm 4 Multi fibre Multi fibre Multi fibre Multi fi
4. 3 0 2 Weight each kgs Ibs 4 0 8 8 6 4 14 1 10 7 23 6 13 5 39 7 2 2 4 8 6 9 15 2 Finish options Apple Apple Apple Apple Apple Apple Dark Oak Dark Oak Dark Oak Dark Oak Dark Oak Dark Oak TANNOY SET UP DIAGRAMS SET UP DIAGRAMS FIG 3 FIG 5 1 0 METRE OR MORE 0 5 METRES OR MORE i 0 15TO45METRS HEIGHT FROM FLOOR 1 5 2 0 METRES N 62 ov O 1 5 TO 4 5 METRES Hace a e ETA w W LL HS gt wo oO FIG 4 FIG 6 TO RIGHT SPEAKER NE ina i L R m HIGH FREQUENCY R LF POWER AMPLIFIER POWER AMPLIFIER LOW FREGUENCY POWER AMPLIFIER LF HF HF LF o HE HF L R LINKS REMOVED LINKS REMOVED
5. TANNOY HEAR BELIEVE F 44 0 1236 428230 F 519 745 2364 F 0180 1111 882 E enquiries tannoy com T 519 745 1158 T 0180 1111 88 1 Tannoy North America Tannoy United Kingdom T 44 0 1236 420199 E inquiries tannoyna com Tannoy Deutschland E info tannoy com Tannoy adopts a policy of continuous improvement and product specification is subject to change tannoyecom 6481 0406 09 05 TANNOY MERCURY OWNER S MAN UAL MERCURY OWNER S MANUAL CONTENTS INTRODUCTION 2 BI AMPING 6 AMPLIFIER MATCHING 3 SCREENING 7 FINE TUNING 4 TECHNICAL SPECIFICATIONS 8 BASS TUNING 5 SET UP DIAGRAMS 9 11 WARRANTY This equipment has been produced and tested with care and precision All Tannoy speaker systems are built to give first class service and carry a 5year warranty Active subwoofers carry a 1 year warranty If the equipment proves to be defective within this period for any reason other than accident misuse unauthorised modification or fair wear and tear Tannoy will repair any such defect or at our option replace it without charge for parts labour or return carriage This warranty is given in addition to the customer s statutory rights If you suspect a problem with your loudspeakers please contact your local Tannoy dealer who will be able to advise on appropriate action INTRODUCTION
6. amplifier right channel output once again ensuring that polarity is correct throughout Switch the amplifier on with the volume control set at its lowest setting Select a favourite source and slowly turn up the volume to a low level Check that bass and treble information is being reproduced from both speakers if not switch off the amplifier and recheck the connections BI AMPING Bi Amping extends the principle of bi wiring one stage further In this connection option separate power amplifiers are used for bass and treble signals in each loudspeaker Four mono or two stereo amplifiers of the same type are required for a stereo pair of loudspeakers Ensure that the links between the loudspeaker terminals are removed and that correct polarity is maintained throughout If two stereo amplifiers are used it is recommended that one amplifier supply bass information to left and right loudspeakers and the other the treble information See figure 6 GRILLES Special acoustically transparent material is used on the grilles However for ultimate fidelity the enthusiast will appreciate the slight improvement in clarity and detail that is achieved by removing the grilles during listening CARE OF THE CABINET Vinyl finished enclosures normally require no more than a wipe with a dry polishing cloth Fingerprints or other more stubborn marks need only a gentle wipe with a slightly damp cloth Real wood veneer cabinets should only be cleaned wit
7. bre coated Multi fibre Multi fibre coated pulped coated pulped coated pulped pulped paper coated pulped coated pulped paper cone papercone papercone cone paper cone paper cone Shielded Yes Yes Yes Yes Yes Yes FIG 2 CROSSOVER Crossover frequency 2 9 kHz 2 8 kHz 2 7 kHz 2 7 2 9 2 8 TO RIGHT Type 4th order Ath order 4th order 4th order Ath order 4th order SPEAKER acoustic acoustic acoustic acoustic acoustic acoustic Linkwitz Riley Linkwitz Riley Linkwitz Riley Linkwitz Riley Linkwitz Riley Linkwitz Riley CABINET Enclosure type Front reflex Front reflex Front reflex Front reflex Rear reflex Twin Rear ie reflex R Construction 15mm particle 15mm particle 15mm particle 15mm particle 15mm particle 15mm particle POWER AMPLIFIER board internally board internally board internally board internally board internally board internally cross braced cross braced cross braced cross braced cross braced cross braced enclosure enclosure enclosure enclosure enclosure enclosure 19mm MDF 19mmMDF 19mmMDF 19mmMDF 19mm MDF 9mm MDF 2 Gi SF ala EF S front baffle front baffle front baffle front baffle front baffle front baffle LINKS IN PLACE Dimensions inc grille 300x 170x 380x204 x 850x204x 970x204x 210x140x 150x430 x mm inches 220 275 275 290 160 70 11 x6 x 15x8x 334x8x 344x8x 8 x5 x 5A x16 x 8 11 114 11 4 6 4 6h Volume litres cubic feet 6 6 0 24 14 3 0 53 23 0 85 40 1 5 2 6 0 1 5
8. h a dry cloth or with a light application of quality non silicon furniture polish It should be remembered that as a natural substance all wood products will change colour when exposed to the UV content of ambient light Light veneer will darken appreciably to a rich natural patina it is advisable to remove the front grille for the first few weeks of use to ensure an even colouration overall HOME CINEMA 5 1 Unlike other forms of encoded surround audio 5 1 offers full bandwidth capability for the surround and centre channels with the ability to treat the subwoofer as a single discreet channel for special effects playback or for music applications as a dedicated low frequency instrument channel This places new demands on the surround and centre channel loudspeakers in both the mixing environment and the playback environment The 5 1 format allows the mix engineer in the recording studio to assign audio information to one or more discreet channels of playback providing very vivid and exacting localisation for the apparent sound sources in the listening environment To reliably recreate that accurate localisation during playback the selection and location of loudspeakers becomes the single most critical issue next to the talent of the mix engineer in the studio THE SYSTEM A fully operational 5 1 system consists of two main front loudspeakers two rear effects speakers at the rear usually wall mounted and a centre channel The subwoofer prov
9. height As with the main speakers the front baffle panel should be as near as possible in line with the screen surface REAR EFFECTS SPEAKERS The integrity of the special effects soundstage created by the source material will be compromised if the speakers are installed on the sidewalls for that reason they should always be placed behind the main viewing position The placement of floor standing speakers at the rear should mirror as near as possible the location of the front pair and 0 5 metres 20 inches from the rear wall Wall mounted loudspeakers should be shelf or bracket mounted 1 5 to 4 5 metres 5ft to 15ft apart with a height mounting height range of 1 5 to 2 metres 5ft to 7ft SUBWOOFER As the subwoofer only produces low frequency therefore monaural information it is difficult to detect its location by ear It could as a result be situated anywhere in the room but optimum performance will be gained by locating the subwoofer between the main stereo pair of speakers Bass output will increase when placed next to a wall or in a corner so use the subwoofer volume control to balance the output with the rest of the system For best results on a carpeted floor screw the spikes provided into the threaded inserts underneath the cabinet and adjust until level then tighten the lock nuts firmly but without undue force On a polished wooden floor use the discs included in the accessory pack under the spike points to prevent damage to
10. ial that the coupling links between the loudspeaker terminals be removed Avoid potential damage to your amplifier ensure that all connections are secure and the polarity is correct in al wiring See figure 4 Be sure that the amplifier is switched OFF and then prepare the two sets of cabling for each side of the system separately Measure and cut four lengths of cable two per speaker Label two of the cable lengths Left LF and Left HF low frequency and high frequency then repeat this process for the right pair Undo the speaker terminals and remove the link bar retain these in a safe place for future use If your amplifier is not equipped with separate output terminals for bass and treble information then at the amplifier end of the cables twist the Left LF positive and the Left HF positive together Connect these to the amplifier Left channel positive terminal marked plus or coloured red Twist the Left LF negative and the HF negative cables together and connect them to the amplifier Left channel negative terminal marked minus or coloured black TANNOY At the loudspeaker end connect the cables labelled Left LF and Left LF to the left hand loudspeaker LF terminals ensuring that you note the polarity markings on the cable sheathing Then proceed to connect the Left HF and Left HF to the HF terminals on the same loudspeaker Repeat this process to connect the right hand loudspeaker to the
11. ides the 1 part of the system See figure 5 SCREENING Loudspeaker drive units contain large magnets These are capable of generating a substantial magnetic field extending a considerable distance beyond the sidewalls of the speaker enclosure This field can cause picture distortion if the speakers are placed too close to the TV However to avoid these colour fringing effects all Mercury models are fully shielded FRONT SPEAKERS The main speaker pair provides much of the delivery of the front soundstage they should therefore be large enough to handle the power output and dynamics required Stand mounted speakers can be used for this purpose but the power handling and extra bass extension achievable from floor standing models will add greatly to the overall assurance of the performance The speakers should be positioned either side of the TV or projection screen placed in line with the screen surface Hace a e ETA CENTRE CHANNEL SPEAKERS As the main effects speaker for the front soundstage the critical factor in its performance is placement In all cases the centre channel speaker should be placed as near to the TV screen as possible effective shielding will allow placement on top of the TV itself If the shape of the top of the TV casing will not allow a stable placement it can be shelf mounted just above The viewing position when seated determines the ideal mounting height but in all cases this should be as close as possible to ear
12. nd the floor brings about an improvement in clarity bass spee and definition First level the spikes by eye then hand tighten the lock nuts Rock the loudspeaker gently from side to side so that the spikes find their way through the weave of the carpet and on to the solid surface below Once fine adjustments have been made to level the loudspeaker and ensure stability tighten the lock nuts firmly but without using undue force Refer to the paragraph headed Positioning for floor standing speaker placement advice See figure 3 BASS TUNING Floor standing loudspeakers with a sealed mass loading cavity in the base of the cabinet can be loaded with either dry sand or lead shot This cavity is accessed by removing the rubber bung from the small hole in the rear of the enclosure the loading material can then be carefully inserted The increase in mass and improved stability will further enhance the bass definition and overall dynamic performance Many Tannoy loudspeakers are also provided with a foam port damper bung inside the port tube located on the front or rear panel of the cabinet The speakers have been designed for use in rooms with average to good acoustics without these dampers fitted so please take them out before use In smaller rooms where loudspeaker positioning is forced closer to rear or side walls the port damper can be inserted into the reflex port This will reduce the bass energy but speed up the sound presentation There is
13. pacity Care should be taken to avoid overdriving any amplifier as this will cause output overload resulting in clipping or distortion within the output signal This if done for any extended period will cause damage to the speakers Generally an amplifier of higher power that is running hard but free of distortion will do less damage to the loudspeaker than a lower power amplifier continually clipping Remember also that a high powered amplifier running at less than 90 of output power generally sounds a great deal better than a lower powered example struggling to achieve 100 An amplifier with insufficient drive capability will not allow the full performance of the loudspeakers to be realised ont Jo tee to FE I CABLE CHOICE Always use the best quality of cable available within your budget High quality audio signals passing from the amplifier to the loudspeaker are unusual in their demands on the cable Wide dynamic range and frequency bandwidth information has to coexist with the ability to transmit peak currents of at least 10amps without incurring any loss or signal impairment This explains why the sound quality of the information reproduced by the loudspeakers is so dependant on the physical properties of the cables connecting them to the amplifier Technically we recommend two core cable with cross section area not less than 1 5 square millimetres 1 5mm for cable runs of up to 3 metres For longer lengths you will requi
14. re to use cable with a minimum cross sectional area of 2 5 square millimetres 2 5mm In addition always keep the cable runs the same length for each speaker Cable construction can affect the sound quality Be prepared to experiment to find a cable that suits your ear and audio system We do not recommend the use of braided Litz or coaxial cables as these have a high capacitance that may affect the stability of certain amplifiers QUICK SET UP PLEASE REFER TO THE SPECIFICATION AND INSTALLATION DIAGRAM SHEET SUPPLIED WITH THIS MANUAL 1 Remove the loudspeakers from all packaging Fold the carton flaps right back and invert the carton and contents Lift the carton clear of the contents Remove all the inner packaging from the product See figure 1 It is strongly recommended that you store all the packaging to allow protected transportation in future 2 Stand mounting or bookshelf speakers should be located securely in an appropriate position If wall mounting any speakers we strongly recommend that you use a bracket which will support the base of the speaker Use of a bracket that screws directly onto the back panel of the speaker can cause too much strain to be exerted on the fixing point and the panel itself This may cause panel detachment when in use and could present the risk of injury 3 Floor standing models perform best with carpet piercing spikes fitted These are supplied along with lock nuts and should be fitted into the th
15. readed holes in the base of the cabinet Level the speaker and then tighten the lock nuts firmly but without using undue force Spike locating cups are provided in the accessory pack and these may be used to protect sensitive floor surfaces TANNOY 4 To protect your speakers and amplifier from damage it is important to ensure that the amplifier is switched OFF prior to connecting or disconnecting any cabling Correct polarity of the cable connections between the amplifier and speakers is essential See figure 2 For optimum performance when connecting the system in standard single wire mode to a speaker terminal panel equipped with full bi wiring facility always make cable connections with the links fitted to the HF terminals See figure 2 The positive plus terminal on the amplifier left channel marked or coloured red must be connected to the positive terminal on the left speaker The left speaker is the one on the left as you look at the stereo pair from your listening position The negative minus terminal on the amplifier left channel marked or coloured black must be connected to the negative terminal on the left speaker Repeat this connection process for the right speaker Remember that the positive or red on the amplifier must be connected to the positive or red on the speaker and the negative or black to negative Select a signal source such as a CD player switch on the amplifier and slo
16. wly turn up the volume control to check that both loudspeakers are reproducing bass and treble information FINE TUNING To get best results from your new Tannoy loudspeakers it is worthwhile spending a little time finding the optimum set up configuration Here are a few tips to help you with this process STAND MOUNTING AND BOOKSHELF SPEAKERS Small speakers should not be placed directly on the floor but can be used on bookshelves or tables However the sound reproduction quality achieved will never be as good when not ideally positioned Your dealer can show you a selection of purpose built stands designed to realise the full performance potential of your loudspeakers Loudspeaker stands should be rigidly built and preferably mass loaded with dry sand The optimum listening height will be dictated by the seating in your room usually between 300mm 12 and 600mm 24 high Stand mounted speakers will produce their best stereo image and soundstage if you can just see the top face of the cabinet Check the lift needed to put the speakers in this position before purchasing your stands Refer to the paragraph headed Positioning for stand mounted speaker placement advice See figure 3 FLOOR STANDING LOUDSPEAKERS For optimum performance from floor standing loudspeakers the design team at Tannoy recommends that the supplied carpet piercing spikes be fitted A rigid footing for the speaker with a secure interface between the cabinet a

Download Pdf Manuals

image

Related Search

Related Contents

取扱 - ジャニス工業  Hit XG1060 - A WALK USA, INC  USER`S MANUAL  (レグザ編) 約1MB  Sistema GreenStar 2 - stellarsupport global  guia do usuário relógio com velocidade +  "取扱説明書"  Samsung Gear S manual de utilizador  Sitecom Wireless Micro USB Adapter 300N X2  

Copyright © All rights reserved.
Failed to retrieve file