Stanton M.201 DJ Equipment User Manual
Contents
1. 14 Grounding post for turntable connection stanton Always use this connection when using standard turntables with ground cable EK se TE Se SO 15 Phono Inputs Plug your turntables in here When these connectors are used your Ld signal is fed directly to the high quality RIAA a phono pre amplifiers Use this position only 49 48 47 464544 for turntables Line level sources will overload the sensitive phono pre amps and will cause distortion 16 Line Inputs Unbalanced RCA jacks for connecting stereo audio from line level sources such as CD players HiFi VCRs cassette decks DAT machines laser discs tuners even synthesizers or other mixing consoles NOTE Plug mono audio sources into both Left and Right inputs using cable connector 17 Master Output Unbalanced RCA connectors controlled by the Master level 18 Power Switch turns unit off and on Note Remember to turn ALL volume levels down when turning on off the unit 19 Power Connector Plug in the included power supply here QUICK SETUP DIAGRAM Study this setup diagram Make sure all faders are at Zero and all devices are off First connect all input sources and processors Next connect your microphone and monitor headphones Finally connect the stereo outputs to the power amplifier s and or audio receivers such a2. EQ 9 2dB 13KHz 15 3dB AT 13KHz MID 9 2dB AT 1KHz LESS THAN 23dB AT 1KHz LOW 9 2dB AT 70Hz 26 3dB AT 70Hz POWER SOURCE AC 9V 1000mA DIMENSIONS 230 W X 267 D X 111 H mm WEIGHT 1 61Kgs Stanton Magnetics Inc Warranty Provision Returns for Repairs or Replacement WARRANTY Through Stanton s authorized dealers around the World Stanton or one of Stanton s authorized distributors outside the U S will without charge repair or replace at the sole discretion of the entity responsible for making the repair or providing the replacement any Stanton merchandise proved defective in material or workmanship for a period of one 1 year following the date of original purchase Exceptions to this warranty are as noted below The warranty for mechanical parts which are subject to wear and tear are limited to the earlier to occur of thirty 30 days following the date of original purchase or the following number of cycles Faders 15 000 Rotary potentiometers 10 000 and Switches 10 000 Stanton will warrant all replacement parts and repairs for ninety 90 days from the date of original shipment Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty RETURNS Authorized Stanton dealers are only authorized to sell and distribute merchandise within a specific country All goods requiring warranty repair or replacement must be returne
3. accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Unplug this apparatus during lightning storms or when unused for long periods of time servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped This appliance shall not be exposed to dripping or splashing water and that no object filled with liquids such as vases shall be placed on apparatus FEATURES 3 band EQ w input GAIN control per channel Power on off muting Long lasting crossfader MASTER 19 CUE LEVEL CH2 CUE PAN PHONO UNE PHONO LINE sta nt 1 gt 5 8 3 5 5 5 5 5 ts 136 9 POWER 5 5 ef o Input fader Controls individual source levels channels in the mix 2 Input toggle switch Selects which source will be active based on wha
4. 33312 U S A
5. Stanton M 201 la 8 8 8 5 gt gt 9 O Z 5 5 8 2 8 5 8 8 8 O 5 gt gt O 3 3 5 3 3 00000 o lt _ ee 1110 5 SEs PROFESSIONAL DJ MIXER IMPORTANT SAFETY INSTRUCTIONS 10 Read these Instructions Keep these Instructions Heed all Warnings Follow all Instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install accordance with the manufacturer s instructions Do not install near any heat sources such as radiators hear registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 12 Refer Only use attachments
6. aused whether by the negligence of Stanton or otherwise To the extent permitted by law and except as otherwise provided above Stanton disclaims any express or implied warranties of merchantability or fitness for a particular purpose The above warranty provides you with specific legal rights You may also have additional rights which are subject to variation from state to state and country to country If there is a dispute regarding the warranty of merchandise that does not fall under the warranty conditions stated above please include a written explanation with the merchandise when returned pursuant to the terms and conditions set forth herein Please register your product online at www stantondj com or mail your completed warranty card to Stanton Magnetics Inc 3000 SW 42 St Hollywood Florida 33312 412 si Ang pip Jaquiny eles OANI LONGOUd 9321S 3 si 5 MMM ye se jd 559002 5 914 ALNVYYVM NOLNVLS cut along dotted line Stanton Magnetics Inc 3000 SW 42nd Street Hollywood FL
7. d freight prepaid if not hand delivered to the authorized Stanton dealer from whom the merchandise was purchased and in the same country where the merchandise was purchased For purposes of purchases made via the Internet the merchandise must be returned to the authorized Stanton dealer in the country where the authorized Stanton dealer which sold the merchandise to purchaser is located and not the authorized Stanton dealer in the country where the purchaser is located or the country in which the merchandise was received Any returns to a non authorized dealer or to an authorized Stanton dealer not in the same country as the merchandise was intended to be sold or as set forth above will void this warranty To initiate a warranty repair you must contact the authorized Stanton dealer from whom you purchased the merchandise and follow such authorized Stanton dealer s return policy Stanton assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the merchandise Stanton s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability and relating to the merchandise shall not exceed the price received by Stanton from your purchase of such merchandise In no event will Stanton be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however c
8. s tape decks Plug your mixer into AC power Now you are ready to switch everything on IMPORTANT Always switch on your audio input sources such as turntables or CD players first then your mixer and finally any amplifiers When turning off always reverse this operation by turning off amplifiers then your mixer and then input devices TURNTABLE POWER SUPPLY SOUND SYSTEM db SPECIFICATIONS INPUT OUTPUT IMPEDANCE 8 SENSITIVITY LINE 14dB 10K OHM _ 2dB PHONO 50dB 47K OHM 20 MIC 60dB 2 2K OHM 2dB MASTER 1K OHM PHONES 0dB 33 OHM 2dB LOAD 32 OHM MAX OUTPUT THD 1 MASTER MORE THAN 14dBV PHONES MORE THAN 21dBV CHANNEL BALANCE WITHIN FREQUENCY RESPONSE LINE 20 20KHz 2dB PHONO 20 20 2 2 3dB RIAA MIC 20 20KHz 2 34 OUTPUT NOISE IEC A WEIGHTED LINE LESS THAN 90dBV PHONO LESS THAN 80dBV MIC LESS THAN 50dBV THD N MASTER OUTPUT MAXIMUM GAIN w 20kHz LPF LINE LESS THAN 0 05 20 20KHz PHONO LESS THAN 0 1 20 20KHz IEC A WTD MIC LESS THAN 0 2 20 20KHz IEC A WTD PHONES LESS THAN 0 1 20 20KHz FROM LINE INPUT CROSSTALK LESS THAN 80dB AT 1KHz BETWEEN CHANNELS TERMINATED UNUSED INPUTS MIC EQ 10 2dB 10KHz 10 288 100Hz CHANNEL
9. t you have connected to the rear panel input section phono line 3 Channel EQ Adjusts the high mid and low frequency levels of the channels for good sound 4 Channel Gain Adjusts the pre fader volume for cleaner sound 5 Replaceable Crossfader Achieves clean segues between the two input channels Hard left selects Channel 1 Hard right selects Channel 2 With the crossfader centered both channels are live Use the crossfader for fast and seamless segues fades from one channel to the other Note The crossfader is user replaceable in case of failure Simply unscrew the two large screws which hold it in place lift it out and disconnect its cable Re attach the new crossfader and screw the mounting plate back onto the unit you re back in business 6 Mic Input Gain Adjusts microphone input level 7 Mic Input Insert your Microphone with 14 plug here 8 Headphone Input Insert in the 4 plug for your headphones here 9 Channel Cue Cue Pan Used to preview channel audio to your headphones Listen here before bringing up channel faders or moving the crossfader 10 Headphone Level Adjusts cue volume 11 Master Level Controls the overall output level 12 Level Indicators The dual LEDs indicators are used to indicate the master output level of channels Right and Left 13 Mic EQ The mic channel include a two band EQ with a range of 10dB to 10 T an W
Download Pdf Manuals
Related Search