Sony PS-LX300USB Turntable User Manual
Contents
1. within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons A This symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance The Caution Marking is put on the Bottom Enclosure Important Safety Instructions 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Follow all instructions 5 Do not use this apparatus near water 6 Clean only with dry cloth 7 Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart2. stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is Wwe used use caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped WARNING This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocat
3. 11 is necessary Recording audio tracks from the turntable on a computer For details on recording operations refer to the supplied document titled Recording audio tracks of a vinyl record to your computer For details about using the software refer to the Sound Forge Audio Studio LE quick start guide on the supplied CD ROM or on line help of the software Continued N suoiesado 118 1 28 Reference guides for the supplied software Refer to the following instructions e The installation guide for Sound Forge Audio Studio LE Refer to this supplied manual to install Sound Forge Audio Studio LE e The Sound Forge Audio Studio LE tutorial This tutorial provides easy instructions on how to operate the software After installing the software the tutorial appears when you launch the software for the first time e The Sound Forge Audio Studio LE quick start guide on the supplied CD ROM This provides instructions on the basic operation of the software Additional Information Precautions On safety Before operating the unit check that the operating voltage of your unit is identical with that of your local power supply Should any solid object or liquid fall into the cabinet unplug the unit and have it checked by qualified personnel before operating it any further Unplug the unit from the wall outlet if it is not to be used for an extended period of time To disconn
4. resources For more detailed information about recycling of this product please contact your local Civic Office your household waste disposal service or the shop where you purchased the product This equipment has been tested and found to comply with the limits set out in the EMC Directive using a connection cable shorter than 3 meters 30 4 Table of Contents About This Manual 4 Getting Started Unpack Gisser 5 Assembling the Turntable scssssesscssesnseen 5 Hooking Up the Turntable uses 7 Playing a Vinyl Record sseessssssssssssssesssessss 8 Recording Audio Tracks on YOUREOMPUUE snena ecient 9 Additional Information PRECAUTIONS sssasicsssscssssdsitecososeslasiesssnssCetdesssdssstotih 13 MAIMTEMAIN CO sce casita aca iahecceat ceedteaucniee 14 Troubleshooting evesesssesseenetneteseeeetneeisetnetnnte 15 SP CifICALIONS w cesssssssssssssssesnsessnsesnssssnssesssesee 18 Parts and CONtKOIS w sesessssssssessseesseesaseesnseenseee 19 About This Manual Thank you for purchasing the Sony Stereo Turntable System Before operating the unit please read this manual thoroughly and retain it for future reference IBM and PC AT are registered trademarks of International Business Machines Corporation Microsoft Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries In this manual Microsoft Windows XP Home Edition and
5. Microsoft Windows XP Professional are referred to as Windows XP In this manual Microsoft Windows Vista Home Basic Windows Vista Home Premium Windows Vista Business and Windows Vista Ultimate are referred to as Windows Vista Sound Forge is a trademark or registered trademark of Sony Creative Software Inc in the United States and other countries e All other names of systems and products are trademarks or registered trademarks of their respective owners and marks are omitted in this manual Getting Started Unpacking Check that you received the following items with your turntable e Platter with drive belt 1 e Rubber mat 1 e 45 r min adaptor 1 e USB cable 1 e CD ROM Sound Forge Audio Studio LE included 1 Operating Instructions this manual The installation guide for Sound Forge Audio Studio LE e Recording audio tracks of a vinyl record to your computer e Please read this first Assembling the Turntable Wea N A 1 Move the metallic parts inside the larger gear in the direction of the arrow Continued payeys Hu p 58 2 Carefully place the platter on the spindle 3 Using the ribbon loop the drive belt around the motor pulley After looping the belt do not forget to remove the ribbon 4 Place the rubber mat on the platter Note When the AC power cord is plugged after assembling
6. S ONY 3 198 123 14 1 Stereo Turntable System Owner s Record The model number and serial numbers are located at the rear Record these numbers in the spaces provided below Refer to these numbers whenever you call upon your Sony dealer regarding this product Model No PS LX300USB Serial No Operating Instructions PS LX300USB 2008 Sony Corporation 28 To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture To prevent fire do not cover the ventilation of the apparatus with news papers table cloths curtains etc And don t place lighted candles on the apparatus To prevent fire or shock hazard do not place objects filled with liquids such as vases on the apparatus Do not install the appliance in a confined space such as a bookcase or built in cabinet The unit is not disconnected from the AC power source mains as long as it is connected to the wall outlet even if the unit itself has been turned off Install this system so that the power cord can be unplugged from the wall socket immediately in the event of trouble Notice for the customers in the U S A RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL LN This symbol is intended to alert the user to the presence of uninsulated dangerous voltage
7. an Interface Devices and HID compliant consumer control device under Human Interface Devices USB Audio Device under Sound video and game controllers USB Composite Device under Universal Serial Bus controllers e For Windows Vista Control Panel is in the Control Panel Home view 1 Select Settings from the Start menu 2 Select Control Panel 3 Select System and Maintenance 4 Select Device Manager 5 Check the Device manager screen Check the devices installed as follows USB Human Interface Devices and HID compliant consumer control device under Human Interface Devices USB Audio CODEC under Sound video and game controllers USB Composite Device under Universal Serial Bus controllers Notes e When connecting to different USB ports you may have to install USB drivers e When connecting to different USB ports the computer automatically installs the driver again In such case check that the driver is correctly installed as in this procedure The recorded sound is disrupted e The CPU of your computer is overloaded Exit other applications e Other USB devices are connected to your computer and being operated simultaneously Quit operating other USB devices You cannot record sound from the turntable e The audio recording device of your computer is not set correctly See pages 10 and 11 to check the device settings There is noise in recorded sound
8. aranteed to operate with all computers e The turntable is not guaranteed to operate with home built computers operating systems that are personally up graded or multiple operating systems e The turntable is not guaranteed to operate with functions such as system suspend sleep stand by mode and hibernation on all computers Continued N suoiesado F 9 1 0 Installing the supplied software Before recording install the supplied software Sound Forge Audio Studio LE Once you install the software into your computer you do not have to install it again other than that you need to re install it 1 Insert the supplied CD ROM into the CD drive of your computer 2 install the software according to on screen instructions Tip For details about installing the software refer to the Sound Forge Audio Studio LE installation guide Connecting the USB cable Connect the turntable and the computer with the supplied USB cable en To the USB jack f USB cable supplied To the USB port l Computer not supplied Notes e The turntable is not guaranteed to operate with a USB hub or USB extension cable Use the supplied USB cable e Connect the USB cable into the USB jack USB port securely or may cause a malfunction e Disconnect the USB cable when it is not in use e When the turntable and computer are connected via USB cable the audio that is adjusted with t
9. by ASTA or BSI to BS1362 i e marked with or Y mark must be used If the plug supplied with this equipment has a detachable fuse cover be sure to attach the fuse cover after you change the fuse Never use the plug without the fuse cover If you should lose the fuse cover please contact your nearest Sony service station Notice for the customers in the countries applying EU Directives The manufacturer of this product is Sony Corporation 1 7 1 Konan Minato ku Tokyo 108 0075 Japan The Authorized Representative for EMC and product safety is Sony Deutschland GmbH Hedelfinger Strasse 61 70327 Stuttgart Germany For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents For the customers in Europe Disposal of Old Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate a collection systems This symbol on the product or on its packaging indicates that this product shall not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The recycling of materials will help to conserve natural
10. e There are electrical wires fluorescent lights or mobile phones near the turntable Move away from any possible sources of electromagnetic interference Notes e For details on the operation of your computer refer to the operating instructions of your computer There can be some breakdowns that cannot be solved even with Troubleshooting In such cases contact your nearest Sony dealer UO EUOJU ni 1 7e 1 3 Specifications Motor and Platter Drive system Belt drive Motor DC motor Platter 295 mm dia aluminum die cast Speeds 33 1 3 and 45 r min 2 speed Wow and flutter Less than 0 25 WRMS Signal to noise ratio More than 50 dB DIN B Tone Arm Type Dynamic balanced straight shaped with soft damping control Effective arm length 195 mm USB jack Power supply USB bus power compliant 5 V 100 mA The power is supplied by the PC which is connected with an attached USB cable Output jack Plug in power system Dedicated USB jack USB series B connector USB full speed General Power requirements North American model 120 V AC 60 Hz Other models 230 240 V AC 50 60 Hz Power consumption 2W Dimensions Approx 420 x 95 x 360 mm 16 2 x 3 5 s x 14 1 4 in w h d Mass 3 3 kg 7 lb 5 oz Supplied Accessories 45 r min adaptor 1 Platter with drive belt 1 Rubber mat 1 USB cable 1 CD ROM 1 Operating Instructions this manual The installation guide for Sound F
11. e the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help CAUTION You are cautioned that any changes or modification not expressly approved in this manual could void your authority to operate this equipment If you have any questions about this product you may call Sony Customer Information Services Center 1 800 222 7669 or http www sony com Declaration of Conformity Trade Name SONY Model Name PS LX300USB Stereo Turntable System Responsible Party Sony Electronics Inc Address 16450 W Bernardo Dr San Diego CA92127 USA Telephone No 858 942 2230 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Notice for the customers in Canada This class B digital apparatus complies with Canadian ICES 003 NOTICE FOR THE CUSTOMERS IN THE UNITED KINGDOM A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience Should the fuse in the plug supplied need to be replaced a fuse of the same rating as the supplied one and approved
12. ect the cord pull it out by the plug Never pull the cord itself On placement Place the unit on a level surface Avoid placing the unit near electrical appliances such as a television hair dryer or fluorescent lamp which may cause hum or noise Place the unit where it will not be subject to any vibration such as from speakers slamming of doors etc Keep the unit away from direct sunlight extremes of temperature and excessive dust and moisture On repacking Keep the carton and packing materials They provide an ideal container to transport the unit If you have any question or problem concerning your unit that is not covered in this manual please consult your nearest Sony dealer Note on recording The recorded music is limited to private use only Use of the music beyond this limit requires permission of the copyright holders UO EUOJU ne 1 38 14 Maintenance Stylus and record care In order to prevent premature stylus and record wear the stylus and record should be cleaned before playback To clean the stylus brush it from back to front using a good quality stylus cleaning brush Do not clean the stylus with your finger tip When using a fluid stylus cleaner make sure not to moisten the stylus too much af To clean your records wipe thoroughly using a good quality record cleaner Cleaning the cabinet and dust cover Clean the cabinet and dust cover periodically using a so
13. em persist after you have made these checks consult your nearest Sony dealer Playing a vinyl record The tone arm skips skates or does not advance e The turntable is not level Place the turntable on a level surface e The record is dirty or scratched Clean the record with a commercially available record cleaning kit or replace the record Poor sound quality excessive noise intermittent sound etc e The stylus is dirty or worn Remove dust on the stylus using a stylus cleaning brush or replace the worn stylus see page 14 e Dust or dirt has collected on the vinyl record Clean the record using a good quality record cleaner Continued uo1 ew0 U ewone 1 58 1 6 Rumble or low frequency howl e The turntable is placed too close to speakers Move speakers away from the turntable This phenomenon called acoustic feedback occurs when vibrations from the speakers are transmitted through the air or via solid objects such as shelves a cabinet or the floor to the turntable where they are picked up by the stylus amplified and reproduced through the speakers Tempo is incorrect e Incorrect r min Set the r min setting to match the one indicated on the vinyl record Select 33 for 33 3 r min records or 45 for 45 r min records The drive belt is deteriorated e Replace the drive belt For details consult your nearest Sony dealer Platter does not rotate e Make sure t
14. ft dry cloth If stains are difficult to remove use a cloth moistened with a mild detergent solution Do not use solvents such as alcohol benzine or thinner since they will damage the finish Replacing the stylus The life expectancy of the stylus tip is about 500 hours To preserve good sound quality and avoid damage to your records we recommend replacing the stylus within this time limit For a replacement stylus consult your nearest Sony dealer To remove the stylus 1 Turn off and unplug the AC power cords of the turntable and amplifier 2 Protect the stylus with the stylus cover Stylus cover ly 3 Grasp the stylus holder and pull it downward away from the body of the cartridge headshell as shown Cartridge headshell z Stylus holder To install the stylus Do this procedure with the stylus protected by the stylus cover 1 Grasp both sides of the stylus holder then insert the stylus grip into the cartridge headshell receptacle Stylus holder Stylus cover Stylus grip 2 Push up the stylus holder until it clicks so that it locks completely Do not leave any gt space Note Do not push the stylus cover forcefully Otherwise the exposed stylus from the cover may cause injury or damage the stylus Troubleshooting Before going through the check list below first make sure that e The power cord is securely connected e The speaker cords are securely connected Should any probl
15. he power cord is inserted all the way into an AC wall outlet e Make sure that the drive belt is looped around the motor pulley completely The drive belt is broken e Replace the drive belt For details consult your nearest Sony dealer Sound is too low or distorted e The turntable is not connected to the PHONO IN inputs on the amplifier see page 7 USB connection recording The turntable is not detected on your computer e Disconnect the supplied USB cable and connect it again e With the turntable and the computer connected restart the computer e Disconnect the supplied USB cable and restart the computer After restarting connect the computer and the turntable with the supplied USB cable e The device setting of your computer may not be set correctly If the turntable is connected to the computer with the USB cable for the first time the USB Composite Device HID compliant consumer control device USB Human Interface Device and USB Audio Device Windows XP USB Audio CODEC Windows Vista are installed automatically To confirm if the driver is correctly installed check as follows e For Windows XP Control Panel is in Category View 1 Select Control Panel from the Start menu 2 Click Performance and Maintenance 3 Click System 4 Click the Hardware tab and then click Device manager 5 Check the Device manager screen Check the devices installed as follows USB Hum
16. he turntable equalizer is input to the USB port of the computer when playing the turntable to record audio tracks on your computer Tip USB drivers are included in operating systems if you are using Windows XP or Windows Vista USB drivers will be installed automatically when the system is connected to the computer for the first time For details refer to the manual of your computer Setting your computer Before recording set the recording audio device according to the operation system you use as follows e For Windows XP Control Panel is in Category View 1 Select Control Panel from the Start menu 2 Click Sounds Speech and Audio Devices 3 Click Sounds and Audio Devices Click the Audio tab 5 Select USB Audio CODEC for Default device of Sound recording 6 Click OK e For Windows Vista Control Panel is in the Control Panel Home view 1 Select Settings from the Start menu Select Control Panel Click Hardware and Sound Click Sound Click the Recording tab A UW A WwW PN Select USB Audio CODEC for Microphone Click Set default 8 Select USB Audio CODEC then click Properties 9 Click the Advanced tab 10 Select 2 channel ex 2 channel 16 bit 44100 Hz CD Quality from the Default Format drop down list 11 Click 0K Note To input stereo signal from the turntable to the computer performing steps 8 through
17. or moving the turntable the turntable sometimes rotates and the tone arm descends to the platter even if START is not pressed If this occurs press STOP to return the tone arm to the arm stand To remove the dust cover With the dust cover fully opened grasp both sides of the cover then remove it carefully Hinge pocket Tip You can use the turntable leaving the dust cover removed In that case store the cover correctly To install the dust cover Insert the hinge pockets on the dust cover into the hinges on the rear of the cabinet Hooking Up the Turntable The phono cable comes attached to the rear of the cabinet 1 Set the PHONO LINE switch on the rear of the turntable according to the jacks of your stereo system amplifier PHONO LINE When your stereo system amplifier has PHONO input jacks connect to PHONO input jacks set to PHONO The Equalizer function is off e When your stereo system amplifier does not have PHONO input jacks connect to AUX VIDEO input jacks etc set to LINE The Equalizer function is on 2 Connect the cable with the white plug to the white L jack and connect the cable with the red plug to the red R jack Make sure to insert the plugs firmly into the jacks If the plugs are not inserted firmly noise may occur ta 3 Connect the AC power cord Connect the AC po
18. orge Audio Studio LE Recording audio tracks of a vinyl record to your computer Please read this first Design and specifications are subject to change without notice Parts and Controls Spindle 2 45 r min adaptor o Speed select button Rubber mat e 5 Platter Oo Cartridge and headshell N START button 8 Insulator 9 Dust cover fe ot a 3 5 _ N Hinge 11 Tone arm Arm stand Finger lift SIZE SELECTOR STOP button UP DOWN button PHONO LINE switch USB jack uo1 ew0 U ono 1 9 Printed in China http www sony net
19. wer cord to an AC wall outlet after completing all of the connections by performing steps 1 and 2 gt to a wall outlet payeys Hu 7e w Set the SIZE SELECTOR to 17 or 30 Operations 4 Turn the protective cover to expose Playing a Vinyl Record the stylus 5 Close the dust cover A 6 Press START The platter starts rotating 1 6 Note ir 4 Lower the volume of the amplifier to prevent damage 3 to it If the tone arm descends and the stylus touches 2 eT 45 r min the vinyl record a loud creaking noise may occur adaptor and harm the amplifier or speakers Adjust the STOP UP DOWN volume of the amplifier after the stylus descends 7 Adjust the volume on your amplifier 1 Placea vinyl record on the platter When playback is finished The tone arm returns to the arm stand automatically then the platter stops rotating To stop playing Press the STOP button The tone arm returns to the arm stand The platter stops rotating Note Place only one vinyl record on the platter at a time If two or more vinyl records are stacked on the platter the stylus will not make proper contact with the grooves and the quality of reproduction will be impaired 2 Press the Speed select button to select the speed To pause playing Press the UP DOWN button to raise the stylus off the vinyl record To play a different part of the vin
20. yl record 1 After performing step 4 press the UP DOWN button then lift the tone arm 2 Move the tone arm to the position you desire 3 Press the UP DOWN button The tone arm descends to the record then playback starts To play a 17 cm vinyl record Place the supplied 45 r min adaptor on the spindle When you have finished using the adaptor put it back in the adaptor tray Recording Audio Tracks on Your Computer You can record audio tracks of a vinyl record on your computer by e Connecting the turntable and your computer using the supplied USB cable e Using the supplied software Sound Forge Audio Studio LE System requirements for the computer to be connected to the turntable Compliant computer IBM PC AT or compatible computers Operating systems Windows Vista Home Basic Windows Vista Home Premium Windows Vista Business Windows Vista Ultimate Windows XP Home Edition Service Pack 2 or higher Windows XP Professional Service Pack 2 or higher Pre installed manufacturer installed only Operating systems other than those listed above are not supported 64bit operating systems are not supported Hardware Environment Port USB port Required when recording audio tracks of a vinyl record onto a computer via a USB connection The USB jack of the turntable supports USB full speed Notes e For the operating environment mentioned above the turntable is not gu
Download Pdf Manuals
Related Search