Home

Sony 3-299-549-12(1) Home Theater System User Manual

Contents

1. 1 The ENTER button has the same function as the button When you operate the TV the ENTER button is used for selecting a channel and the button is used for selecting menu items 2 This button is only available for the DVD or DMPORT function Depending on the DIGITAL MEDIA PORT adapter this button may not work P The 5 gt PROG SOUND MODE and AUDIO buttons have tactile dots Use the tactile dots as references when operating the system These buttons change to the TV operation buttons when the remote is in TV mode The remote is in TV mode when TV button 22 is lights up Guide to the Control Menu Display You can use the Control Menu display to select a function and to view related information I DISPLAY Press C DISPLAY repeatedly Each time you press C9 DISPLAY the Control Menu display changes 0 9 0 Control Menu display 1 2 Control Menu display 2 appears for certain disc only Control Menu display off Note The Control Menu Display appears only during the DVD function Control Menu display The Control Menu display 1 and 2 will show different items depending on the disc type For details about each item see the pages in parentheses continued uoneuuojuj jeuonippv li 121 Example Control Menu display 1 when playing a D
2. LEVELS Maximum volume level is set to 15 LEVEL2 Maximum volume level is set to 20 LEVEL1 Maximum volume level is set to 30 OFF Off Note This function is available only when CONTROL FOR HDMI is set to ON E YCsCr RGB HDMI You can select the type of HDMI signal output from HDMI OUT jack YCsCr The system outputs YCBCr signals RGB The system outputs RGB signals Note If the playback picture becomes distorted set YCsCr to RGB If the HDMI OUT jack is connected to a component with a DVI jack RGB signals will be automatically output even when you select Y CBCn continued sjueunsn py pue sumas pesueapy H 93 GB 94 W AUDIO HDMI You can select the audio output status from the HDMI OUT jack OFF The system does not output the sound from the HDMI OUT jack ON The system outputs audio signals by converting Dolby Digital DTS or 96 kHz 24 bit PCM signals to 48 kHz 16 bit PCM Note When you connect the control unit and TV with an HDMI cable and ON is selected AUDIO DRC A V SYNC TONE DEC MODE and sound mode are not applied to the sound that is output from the TV When you set the function to other than DVD the system does not output the sound from the HDMI OUT jack even if you set AUDIO HDMI to ON E JPEG RESOLUTION You can select the resolution of JPEG image files output from the
3. in MENU AUDIO and SUBTITLE select and enter a language code from Language Code List page 114 using the numeric buttons Settings for the Display VIDEO SETUP Select settings according to the TV to be connected VIDEO SETUP TV TYPE 16 9 PROGRESSIVE COMPONENT OUT OFF 4 3 OUTPUT FULL PAUSE MODE AUTO E TV TYPE You can select the aspect ratio of the connected TV 16 9 Select this when you connect a wide screen TV or a TV with a wide mode function 4 3 LETTER Select this when you connect a 4 3 BOX screen TV Displays a wide picture with bands on the upper and lower portions of the screen 4 3 PAN SCAN Select this when you connect a 4 3 screen TV The system automatically displays the wide picture on the entire screen and cuts off the portions that do not fit continued sjueunsn py pue sbuas pooueapy H 91 GB 9265 Note Depending on the DVD 4 3 LETTER BOX may be selected automatically instead of 4 3 PAN SCAN or vice versa E PROGRESSIVE COMPONENT OUT You can set the progressive signal that is output from the COMPONENT VIDEO OUT jacks to on off For details see Does your TV accept progressive signals page 37 ON The system outputs interlace signals OFF The system outputs progressive signals When you select ON follow the steps below 1 Select ON then press 5 The confirmation display appears 2
4. 3 Make sure to use the same screws to secure the wireless transmitter Rear of the subwoofer Do not use other screws to fasten the wireless transmitter To insert the wireless transceiver into the S AIR sub unit surround amplifier Wireless transceiver Connecting the TV Use the parts as follows Video cord 1 To listen to TV sound from the speakers of the system connect the TV and the system with the audio cord not supplied For video output to your TV check the video input jacks of the TV and select connection method or Q Picture quality improves in order from standard to HDMI When the TV has the digital optical or coaxial output jack you can improve sound quality by connecting with the digital cord 2658 Audio cord not supplied js ce White Digital optical cord not supplied To the digital optical output jack of the TV c O D 5 e m 4 5 D o Rear of the control unit Video cord supplied Gy a To the VIDEO IN jack of the TV HDMI cable not supplied TV To the HDMI IN jack ofthe TV B Component video cord not supplied m gt Green LIT Blue Ti avant Red lt Gay To the COMPONENT VIDEO IN jacks of the TV If your TV accepts progressive format signals use this connection and set the outpu
5. GRAPHICS A preset picture stored in the system appears BLUE The background is blue BLACK The background is black E PARENTAL CONTROL You can set the playback restrictions For details see Restricting Playback of the Disc page 86 E DivX You can display the registration code for this system For more information go to http www divx com on the Internet E MULTI DISC RESUME DVD VIDEO VIDEO CD only You can set the MULTI DISC RESUME function to on or off ON The system stores the resume points in memory for up to 10 discs OFF The system does not store the resume points in memory Playback restarts at the resume point only for the current disc in the system E RESET You can return the SETUP settings other than PARENTAL CONTROL to the default settings For details see Returning the SETUP settings to the default page 99 Settings for the Speakers SPEAKER SETUP To obtain the best possible surround sound set connection of the speakers and their distance from your listening position Then use the test tone to adjust the level and the balance of the speakers to the same level SPEAKER SETUP CONNECTION DISTANCE FRONT DISTANCE SURROUND LEVEL FRONT LEVEL SURROUND TI FRONT CENTER SURROUND SUBWOOFER E CONNECTION If you do not connect center or surround speakers set the parameters for CENTER and SURROUND Since the front s
6. INFORMATION MODE 84 Installing the speakers on a wall 15 Instant advance 40 Instant replay 40 Interlace format 113 INTERVAL 59 J JPEG image file 56 JPEG RESOLUTION 94 L Language Code List 114 LANGUAGE SETUP 91 LEVEL 98 M MENU 91 MIDDLE 66 MODE MUSIC IMAGE 59 MP3 56 Multi Session CD 8 MULTI DISC RESUME 45 96 Multiplex broadcast sound 82 MUTING 40 N Naming preset stations 69 NIGHT MODE 83 O OMNI DIRECTIONAL SOUND 65 ORIGINAL 51 OSD 91 P PARENTAL CONTROL 86 96 114 Parental Control 113 PAUSE MODE 92 PBC Playback 62 PICTURE NAVI 57 PLAY LIST 51 Playable Discs 6 Program Play 46 PROGRESSIVE COMPONENT OUT 92 Progressive format 37 113 Q Quick Setup 34 R RDS 70 Rear panel 116 Region Code 8 Remote 11 120 Repeat Play 48 RESET 96 99 Resume Play 45 S S AIR 113 S AIR SETUP 94 S AIR STBY 76 SCREEN SAVER 95 SETUP 90 99 Shuffle Play 47 SLEEP 83 Slide Show 59 Slow motion Play 40 Soft touch button 38 Sound Mode 65 SPEAKER SETUP 96 SUBTITLE 91 Subwoofer 118 SYSTEM MENU 42 43 63 64 67 68 69 76 79 84 85 SYSTEM SETUP 95 T TEST TONE 98 TRACK SELECTION 95 TREBLE 66 Troubleshooting 102 TV connection 26 TV TYPE 91 U Unpacking 10 V VIDEO SETUP 91 VOLUME LIMIT 93 uoneunoju jeuonippv 125
7. Settings for the Display 9 VIDEO SETUP Settings for the HDMI 93 HDMI SETUP Settings for the Audio 94 AUDIO SETUP Other Settings 95 SYSTEM SETUP Settings for the Speakers 96 SPEAKER SETUP Returning to the Default Settings 99 Additional Information Precautions 100 Notes about the Discs 101 Troubleshooting 102 Self diagnosis Function 110 When letters numbers appear in the display Specifications 111 GIoSSSrV aa Gua dived ett mre 112 Language Code List 114 Index to Parts and Controls 115 Guide to the Control Menu Display 121 568 Playable Discs Type Disc logo Characteristics DVD VIDEO DVD VIDEO DVD R DVD RW in DVD VIDEO format or video mode VLD EO DVD R DVD RW in DVD DVD DVD VIDEO format R RW R4 7 DVD R DVD ReWritable DVD R DL VR Video DVD R DVD RW in VR Video Recording mode DVD DVD Recording mode except for g DVD R DL R RW R4 7 VIDEO CD COMPACT VIDEO CD Ver 1 1 and 2 0 discs alice Super VCD CD R CD RW CD ROM in video CD format or Super VCD format CD COMPACT Audio CD CD R CD RW in audio CD format DIGITAL AUDIO DATA CD CD R CD RW CD ROM in DATA CD format
8. Some playback operations of a DVD and VIDEO CD may be intentionally set by software producers Since this system will play a DVD or VIDEO CD according to the disc contents the software producers designed some playback features may not be available Be sure to read the operating instructions supplied with the DVD or VIDEO CD Copyrights This product incorporates copyright protection technology that is protected by U S patents and other intellectual property rights Use of this copyright protection technology must be authorized by Macrovision and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Reverse engineering or disassembly is prohibited This system incorporates with Dolby Digital and Dolby Pro Logic II adaptive matrix surround decoder and the DTS Digital Surround System Manufactured under license from Dolby Laboratories Dolby Pro Logic and the double D symbol are trademarks of Dolby Laboratories Manufactured under license under U S Patent s 5 451 942 5 956 674 5 974 380 5 978 762 6 487 535 amp other U S and worldwide patents issued amp pending DTS and DTS Digital Surround are registered trademarks and the DTS logos and Symbol are trademarks of DTS Inc 1996 2007 DTS Inc All Rights Reserved This system incorporates High Definition Multimedia Interface HDMI technology HDMI the HDMI logo and High Definition Multimedia Interface are trademark
9. There is noise or the sound skips If you use another S AIR main unit place it more than 8 m away from this S AIR main unit Install the S AIR main unit and S AIR sub unit closer together Avoid use of equipment that generates electromagnetic energy such as a microwave oven nstall the S AIR main unit and S AIR sub unit away from other wireless products Stop using another wireless product Change the RF CHANGE setting page 79 Change the ID settings of the S AIR main unit and S AIR sub unit Surround amplifier operation Ifno sound is output from the surround speakers check the status of the POWER ON LINE indicator on the surround amplifier For details of the POWER ON LINE indicator see Step 3 Setting up the Wireless System page 32 Symptom Remedy The power is not turned on Check that the AC power cord mains lead is connected securely The POWER ON LINE Turn off the surround amplifier and remove the AC power cord mains lead of indicator does not turn on the surround amplifier then check the following items Are the and speaker cords short circuited Is anything blocking the ventilation holes of the surround amplifier After checking the above items and fixing any problems connect the AC power cord mains lead of the surround amplifier and turn on the surround amplifier If the cause of the problem cannot be found even after checking all the above items consul
10. page 114 to confirm which language the code represents When the same language is displayed two or more times the DVD VIDEO is recorded in multiple audio formats E DVD VR The types of sound tracks recorded on a disc are displayed Example 1 MAIN main sound 1 SUB sub sound 1 MAIN SUB main and sub sound 2 MAIN 2 SUB 2 MAIN SUB Note 2 MAIN 2 SUB and 2 MAIN SUB do not appear when one audio stream is recorded on the disc E VIDEO CD CD DATA CD MP3 file DATA DVD MP3 file STEREO The standard stereo sound 1 L The sound of the left channel monaural 2 R The sound of the right channel monaural W DATA CD DivX video file DATA DVD DivX video file The choice of DATA CD or DATA DVD audio signal formats differ depending on the DivX video file contained on the disc The format is shown in the display E Super VCD 1 STEREO The stereo sound of the audio track 1 1 1 L The sound of the left channel of the audio track 1 monaural 1 2 R The sound of the right channel of the audio track 1 monaural 2 STEREO The stereo sound of the audio track 2 2 1 L The sound of the left channel of the audio track 2 monaural 2 2 R The sound of the right channel of the audio track 2 monaural Note While the system is playing a Super VCD on which the audio track 2 is not recorded no sound will come out when yo
11. The file has an extension other than AVI or DIVX The DATA CD DATA DVD is not created in a DivX format that conforms to ISO 9660 Level 1 Level 2 or Joliet UDF The DivX video file is larger than 720 width x 576 height The titles of folder file file name are not displayed correctly The system can only display numbers and letters of the alphabets Other characters are displayed as A disc does not start playing from the beginning Program Play Shuffle Play or Repeat Play has been selected Press CLEAR to cancel these functions before playing a disc Resume Play has been selected During stop press W on the control unit or the remote and then start playback page 45 The title DVD or PBC menu automatically appears on the TV screen The system starts playing the disc automatically The DVD features an auto playback function Playback stops automatically Some discs may contain an auto pause signal While playing such a disc the system stops playback at the auto pause signal You cannot perform some functions such as Stop Search Slow motion Play or Repeat Play Depending on the disc you may not be able to perform some of the operations stated Refer to the operating instructions supplied with the disc Symptom Remedy Messages do not appear on the TV In the Setup Display select the desired language for the on screen screen in the language you want
12. a v gt SYSTEM MENU JOL 1 08 o oi 9 l 0 O Press FUNCTION repeatedly until TV appears in the front panel display Press SYSTEM MENU Press t V repeatedly until ATTENUATE appears in the front panel display then press or gt Press 1 4 to select a setting P NA ATT ON You can attenuates the input level The output level is changed ATT OFF Normal input level Press The setting is made 6 Press SYSTEM MENU The system menu turns off ol Note ATTENUATE appears only when the function is set to the TV function 426 Enjoying Sound from all Speakers iE OG eee OG UU o o 7 o E 7 lt aul 9 SYSTEM MENU X ODO Jy onk Pi 90 B 1 Press SYSTEM MENU 2 Press t repeatedly until DEC MODE appears in the front panel display then press or 3 3 Press repeatedly until the decoding mode you want appears in the front panel display When you want to output the TV sound or stereo sound of a 2 channel source from all speakers select PLII MOVIE or PLII MUSIC decoding mode For details see page 63 4 Press The setting is made 5 Press SYSTEM MENU The system menu turns off Depending on your TV you may need to turn off your TV s speaker to enjoy surround sound of the system 4395 446 Vario
13. additional information along with the regular program signal This tuner offers convenient RDS features such as station name display RDS is available only for FM stations RDS may not work properly if the station you are tuned to is not transmitting the RDS signal properly or if the signal strength is weak Notall FM stations provide RDS service nor do they provide the same type of services If you are not familiar with the RDS system check with your local radio stations for details on RDS services in your area Receiving RDS broadcasts Simply select a station from the FM band When you tune in a station that provides RDS services the station name appears in the front panel display fan RDS broadcast is not received a station name will not appear in the front panel display When a station name is displayed you can check the frequency by pressing DISPLAY repeatedly Control for HDMI External Audio Device Using the Control for HDMI Function for BRAVIA Sync This function is available on TVs with the BRAVIA Sync function only By connecting Sony components that are compatible with the Control for HDMI function with an HDMI cable not supplied operation is simplified as below Theatre Mode page 71 One Touch Play page 72 System Power Off page 72 System Audio Control page 72 Volume Limit page 73 Control for HDMI is a mutual control function standard
14. aerial or connect an external antenna aerial if necessary The signal strength of the stations is too weak when tuning in with automatic tuning Use direct tuning eN o stations have been preset or the preset stations have been cleared when tuning by scanning preset stations Preset the stations page 67 Press DISPLAY so that the frequency appears in the front panel display The remote does not function n T T T here are obstacles between the remote and the control unit he distance between the remote and the control unit is too far he remote is not pointed at the remote sensor on the control unit he batteries in the remote are weak A disc does not play T T T T here is no disc inserted he disc is upside down Insert the disc with the playback side facing down he system cannot play CD ROMs etc page 7 he region code on the DVD does not match the system Moisture has condensed inside the control unit and may cause damage to the lenses Remove the disc and leave the control unit turned on for about half an hour T T he disc is not written properly he disc is dirty or flawed continued uoneunuoju euonippv 105 106 Symptom Remedy The MP3 file cannot be played The DATA CD is not recorded in an MP3 format that conforms to ISO 9660 Level 1 Level 2 or Joliet The DATA DVD is not recorded in an MP3 format that confo
15. containing MP3 files JPEG image files and DivX video files and conforming to ISO 9660 Level 1 Level 2 or Joliet extended format DATA DVD _ DVD ROM DVD R DVD RW DVD R DVD RW in DATA DVD format containing MP3 files JPEG image files and DivX video files and conforming to UDF Universal Disk Format 668 MP3 MPEG 1 Audio Layer 3 is a standard format defined by ISO MPEG which compresses audio data MP3 files must be in MPEG 1 Audio Layer 3 format 2 JPEG image files must conform to the DCF image file format DCF Design rule for Camera File system Image standards for digital cameras regulated by Japan Electronics and Information Technology Industries Association JEITA 9 DivX is a video file compression technology developed by DivX Inc DivX DivX Certified and associated logos are trademarks of DivX Inc and are used under license 5A logical format of files and folders on CD ROMs defined by ISO International Organization for Standardization DVD RW DVD RW DVD R DVD VIDEO and the CD logos are trademarks Example of discs that the system cannot play The system cannot play the following discs CD ROM CD R CD RW other than those recorded in the formats listed on page 6 CD ROM recorded in PHOTO CD format Data part of CD Extra CD Graphics disc DVD Audio Data DVD that does not contain MP3 files JPEG image files or DivX video files D
16. lt e e kea gt r lt P gt 1 7 gt LL VC Disc slot a VOLUME Note MUTING Soft touch buttons function by touching lightly Do not press them strongly Do not place objects on the top of the control unit Doing so may activate the soft touch buttons or deactivate the buttons of the control unit Tip Soft touch buttons function when they are lit up You can select the way of displaying the soft touch buttons located on the top of the control unit page 85 3865 Turn on your TV Switch the input selector on the TV to this system Press I The system turns on Unless the mode of the system is set to DVD press FUNCTION on the remote or FUNCTION soft touch button on the control unit to select DVD No Disc appears in the front panel display and the system is ready for loading the disc 4 Load a disc Push the disc into the disc slot until the disc is pulled in automatically Qn o 2 7 o E 7 Labeled side facing to upper surface The disc is drawn into the control unit automatically and the following indication appears in the front panel display eee n an 5 Press C gt on the remote or touch B soft touch button on the control unit The system starts playback continuous play 6 Adjust the VOLUME on the remote or touch the VOLUME soft touch button on
17. mains lead 2065 Connect surround speakers to subwoofer wired connection DIGITAL MEDIA Portable audio source PORT adapter VCR digital satellite receiver or PlayStation etc antenna aerial FM wire antenna Front of the control unit aerial D Bottom of the __ subwoofer F Rear of the AC power cord mains lead subwoofer Front Center speaker R speaker Surround speaker R Front speaker L Surround speaker L 2168 peyeys burjje5 Connecting the Control unit Connect the system connector of the control unit to the SYSTEM CONTROL terminal on the bottom of the subwoofer Insert the plug of the SYSTEM CONTROL cord then secure the screws of the plug Bottom of the subwoofer Rear of the control unit o o 2 LE S 7 D amp E e O0 HI M SPEAKER eles Rear of the subwoofer SYSTEM CONTROL cord Screws Note Before connecting the control unit place the subwoofer on a stable work surface that is larger than the subwoofer Be sure to place a soft cloth on the work surface to avoid damaging the surface of the subwoofer 2268 Connecting the Speakers Connect surround speakers to S AIR surround amplifier wireless connection Insert the speaker connector
18. only sjueunsn py punos 6565 Adjusting the Bass Middle and Treble Level You can adjust the bass middle and treble level easily TONE V O 1 Press TONE repeatedly until BASS MIDDLE or TREBLE appears in the front panel display BASS adjusts the bass level 6 0 6 0 dB 0 5 dB increments MIDDLE adjusts the middle level 76 0 6 0 dB 0 5 dB increments TREBLE adjusts the treble level 6 0 6 0 dB 0 5 dB increments 2 Press to adjust The adjusted value appears in the front panel display 3 Press Note Depending on the sound mode the sound effect may be less noticeable Adjustment of MIDDLE is not available when you connect headphones to the surround amplifier 6652 Presetting Radio Stations You can preset 20 FM stations and 10 AM stations Before tuning make sure to turn down the volume to minimum You can operate the tuner function by observing the following display on the TV screen Current station Current band and preset number SONY RADIO Station name 1 Press FUNCTION repeatedly until FM or AM appears in the front panel display 2 Press and hold TUNING until the auto scanning starts Scanning stops when the system tunes in a station TUNED and STEREO for stereo program light up in the front panel display 3 Press SYSTEM M
19. the control unit The volume level appears on the TV screen and in the front panel display Depending on the system status the volume level may not appear on the TV screen Note When you set the Control for HDMI function to on the TV that is connected to the control unit with an HDMI cable can be sync operated with the system For details see page 70 When you connect the system and TV with an HDMI cable you can operate them simply using the Control for HDMI function For details see page 70 continued 3965 em S x 9 2 G m To save the power in standby mode Press ID while the system turns on then the system enters standby mode To cancel standby mode press ID once To enter power standby mode make sure that the system is in the following status CONTROL FOR HDMI is set to OFF page 71 S AIR STBY is set to OFF page 76 When the system is turned off do not push a disc into the control unit Additional operations To Press Stop Pause Resume play after pause II gt on the remote or B soft touch button on the control unit Go to the next chapter track or scene PPI Go back to the preceding chapter track F lt twice in a second When you press I once you can go to the or scene beginning of the current chapter track or scene Turn off the sound temporarily MUTING To cancel muting press it again or VOLUME to adjust
20. the mains connect the unit to an easily accessible AC outlet Should you notice an abnormality in the unit disconnect the main plug from the AC outlet immediately About This Operating Instructions The instructions in this Operating Instructions describe the controls on the remote You can also use the controls on the control unit if they have the same or similar names as those on the remote The Control Menu items may be different depending on the area DVD may be used as a general term for a DVD VIDEO DVD RW DVD HR and DVD RW DVD R The default setting is underlined About the S AIR function The system is compatible with the S AIR function which allows transmission of sound between S AIR products wirelessly The following S AIR products can be used with the system Surround amplifier supplied You can enjoy surround speaker sound wirelessly S AIR receiver optional You can enjoy system sound in another room The S AIR receiver can be purchased as an option the S AIR product lineup differs depending on the area Notes or instructions for the surround amplifier or S AIR receiver in this operating instructions refer only to when the surround amplifier or S AIR receiver is used For details on the S AIR function see Using an S AIR Product page 74 KI 468 Table of Contents About This Operating Instructions 3 About the S AIR function 3 Playable
21. 1 and version 2 2 2 3 tags are used for a single MP3 file 2 sosiq BuiAe d 10 suonoung snoueA 53 GB 545 Checking the date information of JPEG image file You can check the date information during playback when the Exif tag is recorded in the JPEG image file Press C DISPLAY twice during playback The Control Menu display appears on the TV screen LLLI ey AO I DATA CD JPEG 9 18 200 Date information Exchangeable Image File Format is a digital camera image format defined by the Japan Electronics and Information Technology Industries Association JEITA Date information is MM DD YYY Y MM Month DD Day YYYY Year Date information differs depending on the area Changing the Angles pvo If various angles multi angles for a scene are recorded on a DVD VIDEO you can change the viewing angle Press ANGLE during playback to select the desired angle Note Depending on the DVD VIDEO you may not be able to change the angle even if multi angles are recorded on the DVD VIDEO Displaying the Subtitles CH OE Oe ELIT If subtitles are recorded on a disc you can turn the subtitles on or off during playback If multilingual subtitles are recorded on the disc you can change the subtitle language during playing or turn the subtitles on or off whenever you want Press SUBTITLE during playback to select the desired subtitle language Note Depend
22. 32995491 2 1 Sony Corporation Printed in Malaysia S O N vY 3 299 549 12 1 ILs V II AN J WA WY be he t tf lt w w DVD Home Theatre System Operating Instructions 2008 Sony Corporation http www sony net 208 To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture Do not install the appliance in a confined space such as a bookcase or built in cabinet To reduce the risk of fire do not cover the ventilation opening ofthe apparatus with newspapers tablecloths curtains etc Do not place the naked flame sources such as lighted candles on the apparatus To reduce the risk of fire or electric shock do not expose this apparatus to dripping or splashing and do not place objects filled with liquids such as vases on the apparatus Do not expose batteries or apparatus with battery installed to excessive heat such as sunshine fire or the like CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT This appliance is classified as a CLASS 1 LASER product This label is located at the bottom of the exterior For customers in Europe Disposal of Old Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This symbol on the product or on its packaging indicates that this product shall not be treated as household waste
23. 4 to select CUSTOM then press The Setup Display appears 5 Press to select VIDEO SETUP then press The options for VIDEO SETUP appear 6 Press to select PROGRESSIVE COMPONENT OUT then press 7 Press to select the desired setting then press OFF The system does not output progressive signals Select this setting when your TV does not accept progressive signals or your TV is connected to jacks other than the COMPONENT VIDEO OUT jacks ON The system outputs progressive signals Select this setting when your TV accepts progressive signals and the TV is connected to the COMPONENT VIDEO OUT jacks When you select ON the confirmation display appears Follow the Steps below Press to select START then press The system outputs the progressive signal for 5 seconds Check that the screen is displayed correctly Press gt to select YES then press The system outputs the progressive signal When you select NO the system does not output the progressive signal 3765 O D e m o 5 D o em S r x e 2 7 G 10 Basic Operations Playing a Disc EIXA a LII E a IGED Depending on the DVD VIDEO or VIDEO CD some operations may be different or restricted Refer to the operation details supplied with your disc Soft touch buttons Coo eH VO FUNCTION FUNCTION VOLUME
24. AIR transmitter not supplied is inserted in the subwoofer and the system transmits the sound Current surround format Except for JPEG Lights up when the colour system is set to NTSC 10 11 12 13 14 15 16 17 10 11 Lights up when the HDMI OUT jack is correctly connected to HDCP high bandwidth digital content protection compliant device with HDMI or DVI digital visual interface input 27 Current repeat mode 48 Lights up when the system outputs progressive signals DVD function only 92 Lights up when a disc is loaded DVD function only Displays system s status such as chapter title or track number time information radio frequency playing status decoding mode etc Playing status DVD function only Current surround format Except for JPEG Lights up when the night mode is on 83 uoneuuojuj jeuonippv li 117 Subwoofer Bottom of the subwoofer Ventilation slots SYSTEM CONTROL jack 22 SPEAKER jacks 23 EZW T100 slot 23 CAUTION Please do not remove the screws before installing the EZW T100 e le s E 118 Surround amplifier o e s E Front panel 2 PHONES jack 32 POWER ON OFF 32 POWER ON LINE indi
25. Press 2 to select START The system outputs the progressive signal for 5 seconds Check that the screen is displayed correctly 3 Press 2 to select YES The system outputs the progressive signal If you select NO the system will not output the progressive signal Note PROGRESSIVE COMPONENT OUT is effective only when you connect the control unit and TV with a component video cord page 27 W 4 3 OUTPUT When you use a 16 9 aspect ratio TV you can adjust the aspect ratio to watch 4 3 aspect ratio signals If you can change the aspect ratio on your TV change the setting on your TV not the system FULL Select this when you can change the aspect ratio on your TV NORMAL Select this when you cannot change the aspect ratio on your TV A 16 9 aspect ratio signal with black bands on left and right sides of the image appears 6 0 OOO 16 9 aspect ratio TV wa 4 3 OUTPUT is effective only when you set TV TYPE in VIDEO SETUP to 16 9 E PAUSE MODE DVD VIDEO DVD R DVD RW only You can select the picture in pause mode AUTO The picture including subjects that move dynamically is output with no jitter FRAME The picture including subjects that do not move dynamically is output in high resolution Settings for the HDMI HDMI SETUP HDMI SETUP HDMI RESOLUTION CONTROL FOR HDMI VOLUME LIMIT YCBCR RGB HDMI AUDIO HDMI JPEG RESOLUTION A
26. S AIR sub unit you can establish sound transmission You can use multiple S AIR main unit by setting a different ID for each component To set the ID of the S AIR main unit 1 Press V on the S AIR main unit The system turns on 2 Press FUNCTION repeatedly until DVD appears in the front panel display 3 Press DISPLAY while the system is in stop mode The Control Menu display appears on the TV screen 4 Press 4 4 to select EEN SETUP then press gt The options for SETUP appear 5 Press t to select CUSTOM then press The Setup Display appears 6 Press t to select AUDIO SETUP then press 3 The options for AUDIO SETUP appear T Press v to select S AIR SETUP then press gt When the wireless transmitter is not inserted in the S AIR main unit S AIR SETUP cannot be selected 8 Press tY to select ID then press 9 Press 1 4 to select the desired ID then press G gt You can select any ID A B or C The confirmation display appears 1 0 Press Set the S AIR sub unit to the same ID Sound transmission is established as follows example Other S AIR main S AIR main unit unit S AIR sub unit S AIR sub unit S AIR sub unit To confirm the current ID perform Steps 1 to 7 above When you pair the S AIR main unit with the S AIR sub unit page 77 PAIRING appears beside ID on the display for selecting ID To set the ID of the surround amp
27. Specifications Amplifier section Power output rated Front L Front R rated RMS output power reference Front L Front R Center Surround L Surround R Subwoofer 35 W 35W at 10 ohms 1 kHz 1 THD 50W 50W at 10 ohms 1 kHz 10 THD 50W at 10 ohms 1 kHz 10 THD 50W 50W at 10 ohms 1 kHz 10 THD 100 W at 4 ohms 70 Hz 10 THD 100 W at 4 ohms 500 Hz 10 THD Depending on the decoding mode settings and the source there may be no sound output Inputs Analog TV AUDIO IN Sensitivity 450 250 mV Inputs Digital SAT CABLE COAXIAL IN Impedance 75 ohms DVD system Laser Semiconductor laser Signal format system Tuner section System FM tuner section Tuning range Antenna aerial Antenna aerial terminals Intermediate frequency AM tuner section Tuning range Antenna aerial Intermediate frequency DVD 645 660 nm CD 770 800 nm Emission duration continuous NTSC PAL PLL quartz locked digital synthesizer 87 5 108 0 MHz 50 KHz step FM wire antenna aerial 75 ohms unbalanced 10 7 MHz 531 1 602 kHz with the interval set at 9 kHz AM loop antenna aerial 450 kHz Video section Outputs VIDEO 1 Vp p 75 ohms COMPONENT Y 1 Vp p 75 ohms Pa Ca Pr Cr 0 7 Vp p 75 ohms HDMI OUT Type A 19 pin Speakers Front Center Surround SS IS15 Speaker system Full range speaker system Speak
28. While the TV is in PAP picture and picture mode the System Audio Control function will not work When the TV exits PAP mode the output method of the TV returns to the one before PAP mode f you select a TV program during DVD playback with the system the TV function is automatically set to output TV sound When you activate One Touch Play during watching TV the System Audio Control function is activated and the TV sound is muted You can connect the system and the TV audio digitally For details see Connecting the TV page 26 Setting the Maximum Volume Level of the System Volume Limit If you change the output method ofthe TV to the system speaker on the TV menu or by pressing THEATRE loud sound may be output depending on the volume level of the system You can prevent this by limiting the maximum level ofthe volume For details see VOLUME LIMIT page 93 Using the DIGITAL MEDIA PORT Adapter The DIGITAL MEDIA PORT DMPORT adapter not supplied is for enjoying sound from a portable audio source or computer By connecting a DIGITAL MEDIA PORT adapter you can enjoy sound from the connected component on the system Available DIGITAL MEDIA PORT adapters vary in each area For details on connecting the DIGITAL MEDIA PORT adapter see Connecting the other components page 28 Do not connect an adapter other than the DIGITAL MEDIA PORT adapter Do not connect or disconnect
29. and the S AIR sub unit To set the ID of the S AIR main unit see To set the ID of the S AIR main unit page 75 To set the ID of the surround amplifier see To set the ID of the surround amplifier page 75 To set the ID of the S AIR receiver refer to the operating instructions of the S AIR receiver 3 Press FUNCTION repeatedly until DVD appears in the front panel display 4 Press DISPLAY while the system is in stop mode The Control Menu display appears on the TV screen D Press V to select EEN SETUP then press 5 The options for SETUP appear 6 Press 1 4 to select CUSTOM then press gt The Setup Display appears 7 Press v to select AUDIO SETUP then press 5 The options for AUDIO SETUP appear 8 Press to select S AIR SETUP then press When the wireless transmitter is not inserted in the S AIR main unit S AIR SETUP cannot be selected 9 Press 4 4 to select PAIRING then press G The confirmation display appears 1 0 Press gt to select YES then press The S AIR main unit starts pairing To not perform pairing select NO 1 1 Start pairing of the S AIR sub unit W For the surround amplifier Press POWER on the surround amplifier to turn on the surround amplifier and press PAIRING on the rear panel of the surround amplifier The PAIRING indicator of the surround amplifier flashes red when pairing starts When sound tra
30. appear in the front panel display instead The disc name or track name may not be displayed depending on the text Playing time of MP3 files and DivX video files may not be displayed correctly When the system is playing a VIDEO CD with PBC functions the playing time is displayed in the front panel display Viewing the playing time and remaining time on the TV screen 1 Press DISPLAY during playback The following display appears on the TV screen T 1 01 40 Time information 2 Press DISPLAY repeatedly to change the time information The display and the kinds of time that you can check depend on the disc you are playing E DVD VIDEO DVD VR e T koe oes Playing time of the current title e Tek oes oer Remaining time of the current title C OR eo oie Playing time of the current chapter e CAF oes oe Remaining time of the current chapter W VIDEO CD with PBC functions e RK Playing time of the current scene E VIDEO CD without PBC functions CD oT eR RK Playing time of the current track e Toe Remaining time of the current track e p koe Playing time of the current disc e Doe Remaining time of the current disc E DATA CD MP3 file DATA DVD MP3 file oT FRR Playing time of the current track E DATA CD DivX video file DATA DVD DivX video file e RK aK oe Playing time of the current file Note Characters marks may not be displayed for some lan
31. ask you to enter a new 4 digit password After you enter a new 4 digit password replace the disc in the control unit and press gt When the display for entering your password appears on the TV screen enter your new password Changing the password 1 Press FUNCTION repeatedly until DVD appears in the front panel display 2 Press DISPLAY while the system is in stop mode The Control Menu display appears on the TV screen 3 Press v to select lg SETUP then press gt The options for SETUP appear 4 Press t to select CUSTOM then press The Setup Display appears 5 Press t to select SYSTEM SETUP then press G The options for SYSTEM SETUP appear 6 Press t to select PARENTAL CONTROL gt then press The display for entering the password appears 7 Enter your 4 digit password using the numeric buttons then press gt 8 Press V to select CHANGE PASSWORD then press 9 Enter your 4 digit password using the numeric buttons then press gt 1 0 Enter a new 4 digit password using the numeric buttons then press 1 1 To confirm your password re enter it using the numeric buttons then press O If you make a mistake entering your password Press before you press 5 then input the correct number sjueunsn py pue sBuim s pesueapy H 87 GB 6855 Calibrating the Appropriate Settings Automatically AUTO CALIBRATION D C A C
32. be affected when you set progressive format In this case return the setting to interlace format the default setting page 37 Re connect the connecting cord securely The control unit is connected to an input device that is not HDCP high bandwidth digital content protection compliant HDMI on the front panel display does not light up Ifthe HDMI OUT jack is used for video output change the type of video signal output from the HDMI OUT jack It may solve the problem page 36 Connect the TV and the control unit using a video jack other than the HDMI OUT and switch the TV s input to the connected video input so that you can see the on screen displays Change the type of video signal output from the HDMI OUT jack and switch the TV s input back to HDMI If the picture still does not appear repeat the steps and try other options Picture noise appears The disc is dirty or flawed If the picture output from your system goes through your VCR to get to your TV the copy protection signal applied to some DVD programs could affect picture quality If you still experience problems even when you connect your control unit directly to your TV try connecting your control unit to your TV s video input except for the HDMI jack page 26 Even though you set the aspect ratio in TV TYPE of VIDEO SETUP the picture does not fill the TV screen The aspect ratio on the disc is fixed Colour irregularity occurs
33. disc by its edge Do not touch the surface Do not stick paper or tape on the disc Do not expose the disc to direct sunlight or heat sources such as hot air ducts or leave it in a car parked in direct sunlight as the temperature may rise considerably inside the car After playing store the disc in its case On cleaning Before playing clean the disc with a cleaning cloth Wipe the disc from the center out Do not use solvents such as benzine thinner commercially available cleaners or anti static spray intended for vinyl LPs This system can only play back a standard circular disc Using neither standard nor circular discs e g card heart or star shape may cause a malfunction Do not use a disc that has a commercially available accessory attached such as a label or ring uoneuuojuj jeuonippv 101 102 Troubleshooting If you experience any of the following difficulties while using the system use this troubleshooting guide to help remedy the problem before requesting repairs Should any problem persist consult your nearest Sony dealer Note that if service personnel changes some parts during repair these parts may be retained In the event of a problem with S AIR function have a Sony dealer check the entire system together S AIR main unit control unit and subwoofer and S AIR sub unit Power Symptom Remedy The power is not turned on Check that the AC power cord
34. disc to create your own program You can program up to 99 tracks 1 Press DISPLAY The Control Menu display appears on the TV screen 2 Press t to select EZ PROGRAM then press The options for PROGRAM appear 3 Press t to select SET then press Total time of the programmed tracks 5 Select the track you want to program For example select track 02 Press to select 02 under T then press Selected track PROGRAM ALL CLEAR 1 TRACK 2 TRACK L 3 TRACK 4 TRACK ao 5 TRACK 6 TRACK 7 TRACK IDE Total time of the programmed tracks To program other tracks repeat steps 4 to 5 The programmed tracks are displayed in the selected order Press to start Program Play Program Play starts When the program ends you can restart the same program again by pressing D gt PROGRAM T ALL CLEAR 1 TRACK E gt 2 TRACK 01 3 TRACK 02 4 TRACK 03 BURN 04 6 TRACK 05 7 TRACK TE 06 Tracks recorded on a disc 4 Press gt The cursor moves to the track row T in this case 01 PROGRAM 0 00 00 T ALL CLEAR 1 TRACK 2 TRACK 01 3 TRACK SS 02 4 TRACK 03 5 TRACK 04 6 TRACK 05 7 TRACK hM 06 To return to normal play Press CLEAR while the display for the program setting is not displayed on the TV screen or select OFF in step 3 To play the same program agai
35. etc 1 Press FUNCTION repeatedly until DVD appears in the front panel display 2 Press DISPLAY while the system is in stop mode The Control Menu display appears on the TV screen Press 4 4 to select SETUP then press The options for SETUP appear 4 Press 1 4 to select CUSTOM then press The Setup Display appears 5 Press 1 4 to select HDMI SETUP then press The options for HDMI SETUP appear 6 Press 7 to select HDMI RESOLUTION then press 7 Press t to select the desired setting then press AUTO 1920x1080p The system outputs the optimal video signal for the connected TV 1920x1080i The system outputs 1920 x 1080i video signals 1280x720p The system outputs 1280 x 720p video signals 720x480 576p The system outputs 720 x 480p or 720 x 576p video signals i interlace p progressive Depending on the country model 720x480p may appear Does your TV accept progressive signals Progressive is the method for displaying TV images which reduces flickering and sharpens the image To use this method you need to connect to a TV that accepts progressive signals 1 Press FUNCTION repeatedly until DVD appears in the front panel display 2 Press DISPLAY while the system is in stop mode The Control Menu display appears on the TV screen 3 Press 1 4 to select SETUP then press The options for SETUP appear 4 Press 1
36. local authorized Sony service facility panel display The Control for HDMI function does When HDMI does not light up in the front panel display check the not work HDMI connection page 27 Set the CONTROL FOR HDMI setting in HDMI SETUP to ON pages 71 93 Make sure that the connected component is compatible with the Control for HDMI function Check that the AC power cord mains lead of the connected component is connected securely Check the connected component s setting for the Control for HDMI function Refer to the operating instructions supplied with the component If you change the HDMI connection connect and disconnect the AC power cord mains lead or have a power failure set the CONTROL FOR HDMI setting in HDMI SETUP to OFF then set the CONTROL FOR HDMI setting in HDMI SETUP to ON page 93 For details see Using the Control for HDMI Function for BRAVIA Sync page 70 No sound is output from the system Set the AUDIO HDMI setting in HDMI SETUP to ON page 94 and TV while using the System Audio Make sure that the connected TV is compatible with the System Audio Control function Control function For details see Using the Control for HDMI Function for BRAVIA Sync page 70 Check the connections uoneunuoju euonippv continued 107 10855 The S AIR function Symptom Remedy S AIR connection is not establ
37. of the front and center speakers into the FRONT L FRONT R and CENTER jacks on the bottom of the subwoofer respectively and insert the speaker connector of the surround speakers into the SPEAKER L and SPEAKER R jacks on the rear of the surround amplifier respectively Front speaker R Front speaker L Center speaker Red Green Rear of the White subwoofer Bottom of the subwoofer EZW T100 slot For details see Using an S AIR Product page 74 N CAUTION Please do not remove Rear panel of the the screws before installing the EZW T100 surround amplifier Blue Speaker cords Surround speaker L Surround speaker R continued 2368 O E e O m o ei o o 2 LI S 7 D amp E Connect surround speakers to subwoofer wired connection Connect the connectors of the speaker cords to the corresponding SPEAKER jacks The connectors of the speaker cords have the same colour as the jacks to be connected Front speaker R Front speaker L Center speaker Speaker cords Red Green Rear of the White subwoofer Bottom of the subwoofer EZW T100 slot For details see Using an S AIR Product page 74 N CAUTION Please do not remove the screws before installing the EZW T100 Blue Speaker cords Surround speaker R Surround speaker L 246 Inserting
38. perform the speaker settings in Settings for the Speakers page 96 f you change the position of the speakers reset the speaker settings See Calibrating the Appropriate Settings Automatically page 88 If you want to change any of the settings see Using the Setup Display page 90 For details on AUTO CALIBRATION and the error messages of AUTO CALIBRATION see Calibrating the Appropriate Settings Automatically page 88 continued 3568 O 0 5 e m o 5 9 o o o 2 LI 7 5 E a To recall the Quick Setup display 1 Press FUNCTION repeatedly until DVD appears in the front panel display 2 Press DISPLAY when the system is in stop mode The Control Menu display appears on the TV screen 3 Press 4 4 to select SETUP then press The options for SETUP appear Ser T 0 01 08 DVD VIDEO CUSTOM CUSTOM QUICK 4 Press 4 to select QUICK then press The Quick Setup display appears 3665 Setting the type of video output to match your TV Depending on the connection of the TV page 26 select the type of video output of the system To select the type of video signal output from the HDMI OUT jack When you connect the control unit and the TV with the HDMI cable select the type of video signals output from HDMI OUT jack For details refer also to the operating instructions supplied with the TV projector
39. that only the CONNECTION setting does not return to the default setting Returning to the Default Settings Returning the system parameters such as preset stations to the default settings yo 1 Turn off the power 2 Press and hold l on the control unit about 5 seconds MEMORY CLR and PUSH POWER appear alternately in the front panel display about 10 seconds 3 Press yo CLEARING appears in the front panel display and the default settings are returned After CLEARED appears the system is turned off e In step 3 if you do not press ID or press any buttons other than I C on the control unit the system turns on The setting is not made When you turn on the system after returning to the default settings wait about 20 seconds before turning on the power by pressing ID Returning the SETUP settings to the default 1 Press FUNCTION repeatedly until DVD appears in the front panel display 2 Press DISPLAY when the system is in stop mode The Control Menu display appears on the TV screen Press to select EEN SETUP then press gt The options for SETUP appear 4 Press t to select CUSTOM then press 5 The Setup Display appears 5 Press t to select SYSTEM SETUP then press 3 The options for SYSTEM SETUP appear 6 Press t to select RESET then press 7 Press 2 to select YES You can also quit the process and return
40. the sound volume Stop play and remove the desired disc amp Locate a point quickly by playing a B J or 8 4 while playing a disc Each time you press P lR disc in fast forward or fast reverse or 48 4 during scanning the playback speed changes To return to Scan normal speed press D gt Actual speeds may differ with some discs Watch frame by frame Slow motion P l or lt 4 while the system is in pause mode Each time you Play press P B gt or 8 44 during Slow motion Play the playback speed changes Two speeds are available To return to normal playback speed press D gt Play one frame at a time Freeze e to go to the next frame while the system is in pause mode Press lt e to go to the preceding frame while the system is in pause mode DVD VIDEO DVD VR DVD R DVD RW DVD R DVD RW only To return to normal playback press D gt Replay the previous scene e instant replay during playback 10 seconds before Briefly fast forward the current scene e instant advance during playback 30 seconds after DExcept for JPEG image files 2 Scan speeds may differ with some discs 3 DVD VIDEO DVD R DVD RW VIDEO CD only Except for VIDEO CDs 5For a DATA CD DATA DVD this function works only for DivX video files 9DVD VIDEO DVD RW DVD R only The button can be used except for DivX video files DDVD VIDEO DVD RW DVD R DVD RW DVD R only The button can be used except for Di
41. the input stream the DISTANCE setting may not be effective If all front and surround speakers are not placed at an equal distance from your listening position set the distance according to the closest speaker Do not place the surround speakers farther away from your listening position than the front speakers When the speaker distance setting is not in the recommended range A T A amp m is displayed being the number A indicates over the recommended distance A v indicates below the recommended distance continued sjueunsn py pue sbuas pooueapy H 97 GB 9865 E LEVEL FRONT You can adjust the sound level of the front speakers center speaker and subwoofer Be sure to set TEST TONE to ON for easy adjustment L R Set the front speaker level 0 0 dB between 6 0 dB and 6 0 dB CENTER Set the center speaker level 0 0 dB between 6 0 dB and 6 0 dB SUBWOOFER Set the subwoofer level 0 0 dB between 6 0 dB and 6 0 dB 5 This item appears when you set CENTER to YES in the CONNECTION setting E LEVEL SURROUND You can adjust the sound level of the surround speakers Be sure to set TEST TONE to ON for easy adjustment L R 6 Set the surround speaker level 0 0 dB between 6 0 dB and 6 0 dB 9 This item appears when you set SURROUND to YES in the CONNECTION setting E TEST TONE The speakers will emit a test tone t
42. the wireless transmitter transceiver You can transmit sound from the S AIR main unit to an S AIR product such as a surround amplifier or S AIR receiver An S AIR product is a component that is compatible with the S AIR function To use the S AIR function you need to insert the wireless transmitter transceiver into the subwoofer surround amplifier and S AIR receiver For details of the S AIR function see Using an S AIR Product page 74 When you insert the wireless transmitter transceiver make sure that the AC power cord mains lead is not connected to a wall outlet mains O 0 e m o 5 D o Do not touch the terminals of the wireless transmitter transceiver nsert the wireless transmitter transceiver with the S AIR logo facing up Insert the wireless transmitter transceiver so that the Y marks are aligned Do not insert other than the wireless transceiver into the EZW RT10 slot Do not insert other than the wireless transmitter into the EZW T100 slot To insert the wireless transmitter into the S AIR main unit subwoofer 1 Remove the screws and detach the slot cover Rear of the subwoofer Remove the screws from the slot cover bearing the caution mark Do not remove other screws The slot cover is no longer necessary however keep it after detaching 2 Insert the wireless transmitter Rear of the subwoofer DI continued 2568 o o 2 LI S 7 D 5 E
43. to select a geographic area as the playback limitation level then press 5 The area is selected When you select OTHERS select and enter a standard code in the table of Parental Control Area Code List page 114 using the numeric buttons 1 0 Press 1 4 to select LEVEL then press The selection items for LEVEL are displayed 1 1 Press t to select the desired level then press 3 PARENTAL CONTROL setting is complete The lower the value the stricter the limitation To turn off the PARENTAL CONTROL function Set LEVEL to OFF in Step 11 To play a disc for which PARENTAL CONTROL is set 1 Load the disc and press D gt The display for entering your password appears on the TV screen 2 Enter your 4 digit password using the numeric buttons then press G gt The system starts playback wa When you play discs which do not have the PARENTAL CONTROL function playback cannot be limited on this system Depending on the disc you may be asked to change the parental control level while playing the disc In this case enter your password then change the level Ifthe Resume Play mode is canceled the level returns to the previous level f you forget your password remove the disc and repeat steps to 7 of Restricting Playback of the Disc page 86 When you are asked to enter your password enter 199703 using the numeric buttons then press The display will
44. used by CEC Consumer Electronics Control for HDMI High Definition Multimedia Interface The Control for HDMI function will not work in the following cases When you connect this system to a component which is not compatible with the Control for HDMI function A component does not have an HDMI jack There are convenient buttons on the system s remote for operating the TV such as THEATRE ONE TOUCH PLAY TV 1 For details see Controlling the TV with the Supplied Remote page 80 and refer to the operating instructions of the TV oNETQUcH t meme P RAT wio UO e BRAVIA Sync Ecc C CD C o GG Depending on the connected component the Control for HDMI function may not work Refer to the operating instructions supplied with the component The Control for HDMI function may not work if you connect a component other than Sony even if the component is compatible with the Control for HDMI function Preparing for the Control for HDMI function Control for HDMI Easy Setting The system is compatible with the Control for HDMI Easy Setting function If the TV is compatible with the Control for HDMI Easy Setting function you can set the system s CONTROL FOR HDMI function automatically by setting the TV For details refer to the operating instructions of the TV If the TV is not compatible with the Control for HDMI Easy Setting function set the Control for HDMI functio
45. va EN TIME page 44 You can check the elapsed time and the remaining playback time Input the time code for picture and music searching m LX ED ETT oo OP PROGRAN page 46 You can select the track to play in the order you want Ur Er 122 SHUFFLE page 47 ee You can play the track file in random order zza EXE Zu I REPEAT page 48 You can play the entire disc all titles all tracks all folders all files repeatedly or one title chapter track folder file repeatedly EZE LEX e EEG GELD CLE DISC MENU page 49 You can display the DVD s menu LE L BROWSING page 58 You can display the list of folders JPEG image files E EH SETUP page 90 CUSTOM In addition to the Quick Setup setting you can adjust various other settings QUICK page 34 You can make the basic adjustments Use Quick Setup to select the desired language of the on screen display the aspect ratio of the TV and select yes or no to start the Auto Calibration EZXA LEX DE EXE es ZZLZ IN FOLDER page 44 You can select the folder to be played EZE E H FILE page 44 You can select the JPEG image file or DivX video file to be played E DATE page 54 You can display the date the picture was taken by a digital camera Ex EH INTERVAL page 59 You can select the duration for which the slides are displayed on the TV screen Erxl EE EFFECT page 60 You can select the effects to be used
46. with very low level inputs or no audio signals If you do the speakers may be damaged when a peak level section is suddenly played On cleaning Clean the cabinet panel and controls with a soft cloth slightly moistened with a mild detergent solution Do not use any type of abrasive pad scouring powder or solvent such as alcohol or benzine If you have any questions or problems concerning your system please consult your nearest Sony dealer Clean the cabinets ofthe surround amplifier only with a soft dry cloth Do not use any type of abrasive pad scouring powder or solvent such as alcohol or benzene On cleaning discs disc lens cleaners Do not use cleaning discs or disc lens cleaners including wet or spray types These may cause the apparatus to malfunction On your TV s colour f the speakers should cause the TV screen to have colour irregularity turn off the TV then turn it on after 15 to 30 minutes If colour irregularity should persist place the speakers further away from the TV set IMPORTANT NOTICE Caution This system is capable of holding a still video image or on screen display image on your television screen indefinitely If you leave the still video image or on screen display image displayed on your TV for an extended period of time you risk permanent damage to your television screen Projection televisions are especially susceptible to this The nameplate is located on the bottom ex
47. 8 NEC 503 517 554 566 NOKIA 521 522 PANASONIC 509 553 572 PHILIPS 515 518 557 570 571 PIONEER 509 525 551 RCA PROSCAN 503 510 544 SABA 530 537 547 549 558 SAMPO 566 SAMSUNG 503 515 517 544 557 566 569 574 SANYO 508 545 567 SHARP 517 535 565 TELEFUNKEN 530 537 547 549 558 THOMSON 530 537 547 549 TOSHIBA 535 541 551 ZENITH 543 567 CATV Manufacturer Code number SONY 821 HAMLIN REGAL 836 837 838 839 840 JERROLD GI 806 807 808 809 810 811 MOTOROLA 812 813 814 JERROLD 830 831 OAK 841 842 843 PANASONIC 816 826 832 833 834 835 PIONEER 828 829 SCIENTIFIC 815 816 817 844 ATLANTA TOCOM PHILIPS 830 831 ZENITH 826 827 Controlling the TV with the remote You can control the TV by using following buttons To use these buttons other than THEATRE and TV IK set the remote to the TV mode by pressing TV so that TV button lights up for 1 second To exit the TV mode press TV so that the TV flashes 4 times wa During the TV mode if you press any of the following buttons TV button lights up Depending on the manufacturer setting some buttons may not work and TV button does not light up When you press other than the following buttons during the remote is in the TV mode TV button flashes 4 times and the remote exits the TV mode automatically Depending on the TV you may not be able to control yo
48. AUTO You can play both the JPEG image files and MP3 files in the same folder as a slide show MUSIC You can play only MP3 files continuously IMAGE You can play only JPEG image files as a slide show Press 3 Press DVD MENU The list of folder recorded on the DATA CD or DATA DVD appears 7 Press t V to select the desired folder and press D gt e dg The system starts playing the selected folder You can turn the folder list on or off by pressing DVD MENU repeatedly Note PICTURE NAVI does not work when you set MODE MUSIC IMAGE to MUSIC If you play large MP3 file and JPEG image file at the same time the sound may skip Sony recommends that you set the MP3 bit rate to 128 kbps or lower when creating the file If the sound still skips then reduce the size of the JPEG file Specifying the slide show duration of JPEG image files 1 Press DISPLAY twice The Control Menu display appears on the TV screen 2 Press Vto select INTERVAL then press The options for INTERVAL appear 3 Press to select a setting NORMAL You can set to the standard duration FAST You can set the duration shorter than NORMAL SLOWI You can set the duration longer than NORMAL SLOW2 You can set the duration longer than SLOWI 4 Press Note Some JPEG image files may take longer to display than the option you selected Especially progressive JPEG i
49. DEC MODE page 63 and set the sound mode page 65 to MOVIE MUSIC or NEWS To cancel select other than A F D STD Depending on the type of DIGITAL MEDIA PORT adapter you may be able to operate a connected component using either the buttons on the remote or the control unit The following illustration shows an example of buttons that can be used in this case Using an S AIR Product The system is compatible with the S AIR function page 113 which allows sound transmission between S AIR products About S AIR products There are two types of S AIR product S AIR main unit control unit and subwoofer in this system This is for transmitting sound You can use up to 3 S AIR main unit The number of usable S AIR main unit depends on the use environment S AIR sub unit surround amplifier in this system This is for receiving sound Surround amplifier You can enjoy surround speaker sound wirelessly S AIR receiver not supplied You can enjoy system sound in another room gt S AIR sub unit S AIR receiver not supplied S AIR main unit control unit and subwoofer S AIR sub unit surround amplifier Establishing sound transmission between the S AIR main unit and S AIR sub unit ID setting For the surround amplifier supplied For the S AIR receiver not supplied Simply by matching the ID of the S AIR main unit and the
50. DIGITAL MEDIA PORT Adapter page 73 Eg Connect the DIGITAL MEDIA PORT adapter so that the Y marks are aligned When disconnecting pull out while pressing Do not connect or disconnect the DIGITAL MEDIA PORT adapter to from the control unit while the system is turned on You can assign a digital sound input corresponding with the function TV and SAT CABLE For details see DIGITAL IN page 95 2865 If your TV has multiple audio video inputs You can enjoy the sound with the speakers of the system through the connected TV Connect the components as follows VCR digital satellite receiver TV or PlayStation etc VCR digital satellite receiver or PlayStation etc Control unit Signal flow Select the component on the TV For details refer to the operating instructions of the TV If the TV does not have multiple audio video inputs a switcher will be necessary to receive the sound from more than two components 2965 peueijs bunje5 o o 2 LI S 7 D amp E Connecting the Antenna Aerial AM loop antenna aerial supplied A vu Lan Cord A or cord B can be connected to either terminal FM wire antenna aerial supplied Note Keep the AM loop antenna aerial and cord away from the system or other AV components as noise may re
51. Digital Cinema Auto Calibration can set the appropriate surround sound automatically The system outputs a loud test sound when AUTO CALIBRATION starts You cannot turn the volume down Give consideration to children and neighbours Make sure that the headphones are not connected to the surround amplifier You cannot operate the following steps with the headphones connected Before AUTO CALIBRATION be sure that the surround amplifier turns on and you install the surround amplifier in the appropriate location If you install the surround amplifier in an improper location such as another room proper measurement will not be obtained 1 Press FUNCTION repeatedly until DVD appears in the front panel display 2 Press DISPLAY while the system is in stop mode The Control Menu display appears on the TV screen 3 Press 1 4 to select RE SETUP then press 5 The options for SETUP appear 4 Press 4 4 to select CUSTOM then press gt The Setup Display appears 5 Press t to select AUDIO SETUP then press 5 The options for AUDIO SETUP appear 6 Press t to select AUTO CALIBRATION then press The options for AUTO CALIBRATION appear 7 Connect the calibration microphone supplied to the ECM AC2 jack on the rear of the control unit Set up the calibration microphone at the ear level using the tripod etc not supplied The front of each speaker should face the calibration microph
52. Discs ees 6 Getting Started Step 1 Positioning the Speakers 12 Step 2 Connecting the System 19 Step 3 Setting up the Wireless System uquna e HERREN 32 Step 4 Performing the Quick Setup 34 Basic Operations Playing a Disc sees 38 Enjoying the Radio or Other Components 41 Enjoying Sound from all Speakers 43 Various Functions for Playing Discs Searching for a Title Chapter Track Scene elc isses ade cnius 44 Resuming Playback from the Point Where You Stopped the Disc 45 Resume Play Creating Your Own Program 46 Program Play Playing in Random Order 47 Shuffle Play Playing Repeatedly 48 Repeat Play Using the DVD s Menu 49 Changing the Sound 50 Selecting ORIGINAL or PLAY LIST on a DVD VR 51 Viewing Information About the Disc 52 Changing the Angles 54 Displaying the Subtitles 55 Adjusting the Delay Between the Picture and Sound 55 A V SYNC Playing MP3 Files JPEG Image Files 56 Playing MP3 Files and JPEG Image Files as a Slide Show with Sound aaa 59 Enjoying DivX Videos 60 Playing a VIDEO CD with PBC Functions
53. ENU 4 Press V repeatedly until MEMORY appears in the front panel display D press or A preset number appears in the front panel display TUNED STEREO 6 Press t to select the preset number you want TUNED STEREO ry You can select the preset number directly by pressing the numeric buttons 7 Press COMPLETE appears in the front panel display and the station is stored 8 Repeat steps 2 to 7 to store other stations 9 Press SYSTEM MENU The system menu turns off To change the preset number Select the desired preset number by pressing PRESET page 68 then perform the procedure from step 3 suomounq Jeunl a 67 GB Listening to the Radio Preset radio stations in the system s memory first see Presetting Radio Stations page 67 1 Press FUNCTION repeatedly until FM or AM appears in the front panel display The last received station is tuned in 2 Press PRESET repeatedly to select the preset station Each time you press the button the system tunes in one preset station You can select the preset number directly by pressing the numeric buttons 3 Adjust the volume by pressing VOLUME To turn off the radio Press ID to turn off the system To change to another function press FUNCTION To listen to non preset radio stations Use manual or automatic tuning in step 2 For manual tuning press TUN
54. For details of the S AIR function see Using an S AIR Product page 74 POWER ON LINE Indicator S AIR ID switch SURROUND SELECTOR switch PHONES jack The subwoofer transmits sound to the surround amplifier that is connected to the surround speakers To establish sound transmission perform the following steps 1 Press WO on the control unit The system turns on 2 Make sure that the SURROUND SELECTOR switch of the surround amplifier is set to SURROUND 3 Set the S AIR ID switch of the surround amplifier to A 4 Press POWER on the surround amplifier The POWER ON LINE indicator turns green If not check the transmission status as follows 32 GB To check the transmission status You can check the status of sound transmission between the subwoofer and surround amplifier by checking the POWER ON LINE indicator of the surround amplifier POWER ONLINE Status indicator Turns green Sound transmission is established Flashes green Sound transmission is not established For details see Surround amplifier operation page 109 The surround amplifier does not output sound Turns red For details see Surround amplifier operation page 109 The surround amplifier turns off or its protection is active For details see Surround amplifier operation page 109 Turns off To enjoy the sound by using headphones Yo
55. HDMI OUT jack SD The system outputs standard resolution with a black frame HD The system outputs HD resolution with a black frame HD The system outputs the HD resolution without a black frame 1920x1080i HD The system outputs full size HD resolution with a black frame 1920x1080i HD The system outputs full size HD resolution without a black frame Note JPEG RESOLUTION is effective only when you set TV TYPE in VIDEO SETUP to 16 9 and you set HDMI RESOLUTION in HDMI SETUP to other than 720x480 576p You can select 1920 x10801 HD _ or 1920x10801 HD only when you set HDMI RESOLUTION in HDMI SETUP to 1920 x 10801 If you select 1920 x 10801 HD _ or 1920 x 1080i HD next image appears after black screen HDMI signal will stop momentarily when the system is loading or unloading a DATA CD or DATA DVD disc Settings for the Audio AUDIO SETUP AUDIO SETUP S AIR SETUP ce AUTO CALIBRATION DIGITAL IN TV OPT SAT CABLE COAX AUDIO DRC OFF TRACK SELECTION OFF E S AIR SETUP You can set up the S AIR setting For details see Using an S AIR Product page 74 ID You can set the ID of the S AIR main unit PAIRING You can pair the system and S AIR sub unit such as surround amplifier or S AIR receiver Note This functio
56. ING repeatedly For automatic tuning press and hold TUNING The automatic tuning stops automatically when the system receives the radio station To stop the automatic tuning manually press TUNING or Bl To listen to radio stations when you know the frequencies Use direct tuning in step 2 1 Press D TUNING 2 Press the numeric buttons to select the frequency number you want to listen to For example to input 98 0MHz press the numeric buttons in the following order 9 8 0 3 Press To improve reception reorient the connected antennas aerials If an FM program is noisy If an FM program is noisy you can select monaural reception There will be no stereo effect but reception will improve 1 Press SYSTEM MENU 2 Press repeatedly until FM MODE appears in the front panel display then press C or 3 3 Press to select MONO STEREO stereo reception MONO monaural reception 4 Press The setting is made 5 Press SYSTEM MENU The system menu turns off Naming preset stations You can enter a name for preset stations These names for example X YZ appear in the front panel display when a station is selected Only one name can be entered for each preset station 1 Press FUNCTION repeatedly until FM or AM appears in the front panel display The last received station is tuned in 2 Press PRESET repeatedly t
57. IR STBY is set to ON you cannot use any buttons other than VC button When there is no disc in the S AIR main unit and S AIR lights up in the front panel display you can load a disc into the S AIR main unit and enjoy music by the S AIR receiver Identifying the S AIR main unit with a specific S AIR sub unit Pairing operation For the surround amplifier supplied For the S AIR receiver not supplied Itis easy to set the same ID for the S AIR main unit and an S AIR sub unit such as a surround amplifier or S AIR receiver to establish sound transmission However neighbours may also receive your system s sound if IDs are the same or you may receive the sound from neighbours To prevent this you can identify the S AIR main unit with a specific S AIR sub unit by performing the pairing operation E Before pairing Sound transmission is established by the ID example Your room Neighbour S AIR main unit S AIR sub unit S AIR sub unit W After pairing Sound transmission is established between the paired S AIR main unit and S AIR sub unit s only Your room Neighbour S AIR main unit No transmission S AIR sub unit S AIR sub unit Pairing 1 Place the S AIR sub unit that you want to pair near the S AIR main unit Remove headphones from the surround amplifier if connected continued 914 q orpny EUJ9 X3 IIANGH 40 01 U0D a 776 2 Match the IDs of the S AIR main unit
58. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The recycling of materials will help to conserve natural resources For more detailed information about recycling of this product please contact your local Civic Office your household waste disposal service or the shop where you purchased the product For customers in Europe Disposal of waste batteries applicable in the European Union and other European countries with separate collection systems This symbol on the battery or on the packaging indicates that the battery provided with this product shall not be treated as household waste On certain batteries this symbol might be used in combination with a chemical symbol The chemical symbols for mercury Hg or lead Pb are added if the battery contains more than 0 0005 mercury or 0 004 lead By ensuring these batteries are disposed of correctly you will help prevent potentially negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of the battery The recycling of the materials will help to conserve natural resources In case of products that for safety performance or
59. NCTION you disconnect the AC power cord mains lead you change the parental control level Fora DVD VR VIDEO CD CD DATA CD and DATA DVD the system remembers the resume playback point for the current disc Resume Play does not work during Program Play and Shuffle Play This function may not work properly with some discs To play from the beginning of the disc press Bl twice then press gt To enjoy a disc that is played before by resume playback Multi disc Resume DVD VIDEO VIDEO CD only This system recalls the point where you stopped the disc the last time it was played and resumes playback from that point the next time you insert the same disc When the resume playback memory is full the resume playback point for the earliest disc is deleted To activate this function set MULTI DISC RESUME in SYSTEM SETUP to ON For details see MULTI DISC RESUME DVD VIDEO VIDEO CD only page 96 Note If MULTI DISC RESUME in SYSTEM SETUP is set to OFF page 96 the resume point is cleared when you change the function by pressing FUNCTION This system can store at least 10 resume playback points To play from the beginning of the disc press ll twice then press gt sosiq BuiAe d 10 suoljouny snoueA 4505 Creating Your Own Program Program Play I EIN You can play the contents of a disc in the order you want by arranging the order of the tracks on the
60. SM band Industrial Scientific and Medical band such as wireless LANs and Bluetooth applications uoneuuoju euonippv 113 114 Language Code List The language spellings conform to the ISO 639 1988 E F standard Code Language Code Language Code Language Code Language 1027 Afar 1028 Abkhazian 1032 Afrikaans 1039 Amharic 1044 Arabic 1045 Assamese 1051 Aymara 1052 Azerbaijani 1053 Bashkir 1057 Byelorussian 1059 Bulgarian 1060 Bihari 1061 Bislama 1066 Bengali Bangla 1067 Tibetan 1070 Breton 1079 Catalan 1093 Corsican 1097 Czech 1103 Welsh 1105 Danish 1109 German 1130 Bhutani 1142 Greek 1144 English 1145 Esperanto 1149 Spanish 1150 Estonian 1151 Basque 1157 Persian 1165 Finnish 1166 Fiji 1171 Faroese 1174 French 1181 Frisian 1183 Irish 1186 Scots Gaelic 1194 Galician 1196 Guarani 1203 Gujarati 1209 Hausa 1217 Hindi 1226 Croatian 1229 Hungarian 1233 Armenian 1235 Interlingua 1239 Interlingue 1245 Inupiak 1248 Indonesian 1253 Icelandic 1254 Italian 1257 Hebrew 1261 Japanese 1269 Yiddish 1283 Javanese 1287 Georgian 1297 Kazakh 1298 Greenlandic 1299 Cambodian 1300 Kannada 1301 Korean 1305 Kashmiri 1307 Kurdish 1311 Kirghiz 1313 Latin 1326 Lingala 1327 Laothian 1332 Lithuanian 1334 Latvian Lettish 1345 Malagasy 1347 Maori 1349 Macedonian 1350 Malayalam 1352 Mongolian 1353 Moldavian 1356 Marathi 1357 Malay 1358 Maltese 1363 Burmese 1365 Nauru 1369 Nepa
61. UTO 1920x1080p OFF E HDMI RESOLUTION You can select the type of video signal that is output from the HDMI OUT jack For details see To select the type of video signal output from the HDMI OUT jack page 36 AUTO 1920x1080p The system outputs the optimal video signal for the connected TV 1920x1080i The system outputs 1920 x 1080i video signals 1280x720p The system outputs 1280 x 720p video signals 720x480 576p The system outputs 720 x 480p or 720 x 576p video signals i interlace p progressive Depending on the country model 720 x 480p may appear E CONTROL FOR HDMI You can set the CONTROL FOR HDMI function to on off This function is available when you connect the system and TV with an HDMI cable For details see Using the Control for HDMI Function for BRAVIA Sync page 70 OFF Off ON On You can operate mutually between components that are connected with an HDMI cable Note When you set to ON without the HDMI connection of the TV Please verify the HDMI connection appears and you cannot set to ON E VOLUME LIMIT If you change the output method ofthe TV to the system speaker on the TV menu or by pressing THEATRE the System Audio Control page 72 is activated and loud sound may be output depending on the volume level of the system You can prevent this by limiting the maximum level of the volume
62. VD RAM Super Audio CD Also the system cannot play the following discs ADVD VIDEO with a different region code page 8 A disc that has a non standard shape e g card shaped heart shaped A disc that has a commercially available accessory attached such as a label or ring Ring Label b An adapter to convert an 8 cm disc to standard size Adapter A disc with paper or stickers on it A disc that has the adhesive of cellophane tape or a sticker still left on it continued 788 868 Notes about CD R CD RW DVD R DVD RW DVD R DVD RW In some cases CD R CD RW DVD R DVD RW DVD R DVD RW cannot be played on this system due to the recording quality or physical condition of the disc or the characteristics of the recording device and authoring software The disc will not play if it has not been correctly finalized For more information refer to the operating instructions for the recording device Note that some playback functions may not work with some DVD RWs DVD Rs even if they have been correctly finalized In this case view the disc by normal playback Also some DATA CDs DATA DVDs created in Packet Write format cannot be played Music discs encoded with copyright protection technologies This product is designed to play back discs that conform to the Compact Disc CD standard Recently various music discs encoded with copyright protection technologies are marketed by some record companies Please be a
63. VD VIDEO Currently playing title number Currently playing chapter number Total number of titles 2 Playback status Total number of chapters P gt Playback HI Pause W Stop etc Control Menu items Type of disc being played Selected item Playing time Current setting CHAPTER Function name of Options selected Control Menu item HAH gt ENTER Quit Operation message 1 The scene number for a VIDEO CD PBC is on track number for VIDEO CD CD folder number for a DATA CD DATA DVD 2 The index number for a VIDEO CD MP3 file number or JPEG image file number for a DATA CD DATA DVD 3 Super VCD as SVCD MP3 in the Control Menu display 1 or JPEG in the Control Menu display 2 for DATA CD DATA DVD 4 The date is displayed for JPEG image files for certain JPEG image files only To turn off the display Press C9 DISPLAY List of Control Menu items Item Item Name Function Relevant Disc Type EU TITLE page 44 SCENE page 44 TRACK page 44 You can select the title scene or track to be played EZ Em Coo EH CHAPTER page 44 INDEX page 44 You can select the chapter or index to be played ED m Coo TRACK page 44 You can select the track to be played KUN Dum LL E ORIGINAL PLAY LIST page 51 You can select the type of titles DVD RW DVD R to be played the ORIGINAL one or an edited PLAY LIST pvo
64. Ver 2 0 62 PBC Playback Sound Adjustments Enjoying Surround Sound by Using Decoding Mode 63 Selecting the Sound Mode 65 Adjusting the Bass Middle and Treble Level itio dote ette dts 66 Tuner Functions Presetting Radio Stations 67 Listening to the Radio 68 Using the Radio Data System RDS 70 Control for HDMI External Audio Device Using the Control for HDMI Function for BRAVIA Sync 70 Using the DIGITAL MEDIA PORT Adapter eerie teet 73 Using an S AIR Product 74 Other Operations Controlling the TV with the Supplied R tmote sertim nuka 80 Enjoying Multiplex Broadcast Sound 82 DUAL MONO Enjoying the Sound at Low Volume 83 NIGHT MODE Using the Sleep Timer 83 Changing the Brightness of the Front Panel Display Changing the Display Mode INFORMATION MODE Changing the Display Appearance of the Soft touch Buttons 85 ILLUMINATION MODE Advanced Settings and Adjustments Restricting Playback of the Disc 86 PARENTAL CONTROL Calibrating the Appropriate Settings Automatically 88 AUTO CALIBRATION Using the Setup Display 90 Setting the Display or Sound Track Language sercis iiaei 91 LANGUAGE SETUP
65. at all of the folders on the disc FOLDER You can repeat the current folder TRACK MP3 files only You can repeat the current file FILE DivX video files only You can repeat the current file E During Shuffle Play or Program Play OFF Off ON You can repeat Shuffle Play or Program Play 4 Press The item is selected To return to normal play Press CLEAR or select OFF in step 3 To turn off the Control Menu display Press DISPLAY repeatedly until the Control Menu display is turned off wa You cannot use Repeat Play with a VIDEO CD and Super VCD with PBC playback When the system is playing a DATA CD DATA DVD which contains MP3 files and JPEG image files and their playing time is not the same the audio sound will not match the image When MODE MUSIC IMAGE is set to IMAGE page 59 you cannot select TRACK When you press CLEAR to return to normal play Program Play and Shuffle Play are also canceled You can quickly display the REPEAT status Press REPEAT on the remote Using the DVD s Menu ELI A DVD is divided into a lot of sections which make up a picture or music feature These sections are called titles When you play a DVD which contains several titles you can select the title you want using DVD TOP MENU When you play a DVD that allows you to select items such as the language for the subtitles and the language for the sound select these
66. cator 32 PAIRING indicator 78 PAIRING button 78 10 Rear panel Wireless transceiver EZW RT10 slot 26 7 S AIR ID switch 32 SPEAKER L jack 23 SPEAKER R jack 23 SURROUND SELECTOR switch 32 uoneuuojuj jeuonippv li 119 120 Remote control ALPHABETICAL ORDER BUTTON DESCRIPTIONS A O P Z ANALOG 5 PICTURE NAVI 28 Numeric buttons 7 ANGLE 9 PRESET 15 V5 on standby 2 AUDIO 27 PROG tg TV VO on standby 1 CLEAR B9 REPEAT 6 et gt 09 r2 D TUNING t0 SLEEP B3J 0 e gt REPLAY ADVANCE DIGITAL 6 SOUND MODE 19 t6 DIMMER 5 SUBTITLE 10 kea gt gt 15 DISPLAY 3 SYSTEM MENU 13 Aa 23 DVD MENU 11 THEATRE 84 lt a gt 23 DVD TOP MENU 26 TONE 80 r gt 24 ENTER 8 TOOLS OPTIONS 13 m 7 FUNCTION 4 TUNING B3 18 MENU HOME 14 TV P2 DISPLAY 14 MUTING Pil TV VOL Po 2 92 NIGHT B1 VOLUME PO B ONE TOUCH PLAY 85 RETURN 25 3 52 M 6 pg ae 19
67. d 1988 08 Alone 1999 Y 3 Press V to select a folder E To play JPEG image files in a folder Press to start playing the selected folder E To select a JPEG image file by displaying the subscreens Press PICTURE NAVI Images of JPEG image files in the folder appear in 16 subscreens Press 4 gt to select the JPEG image file you want to view then press To return to normal screen press d RETURN continued sosig BulAe g 10 suonoung snoueA g 57 GB 5855 Note PICTURE NAVI does not work when you set MODE MUSIC IMAGE to MUSIC A scroll box is displayed at the right side of the TV screen To display the additional JPEG image files select the bottom JPEG image file and press To return to the previous JPEG image file select the top JPEG image file and press t To play the next or previous JPEG image file Press 2 when the Control Menu display is not displayed on the TV screen Note that you can select the next folder by continuing to press gt after the last image on the current folder but that you cannot return to the previous folder by pressing To return to the previous folder select the folder from the folder list To rotate a JPEG image file When a JPEG image file is displayed on the TV screen you can rotate the JPEG image file by 90 degrees Press 4 while viewing a JPEG image file Press CLEAR to return to normal vie
68. data integrity reasons require a permanent connection with an incorporated battery this battery should be replaced by qualified service staff only To ensure that the battery will be treated properly hand over the product at end of life to the applicable collection point for the recycling of electrical and electronic equipment For all other batteries please view the section on how to remove the battery from the product safely Hand the battery over to the applicable collection point for the recycling of waste batteries For more detailed information about recycling of this product or battery please contact your local Civic Office your household waste disposal service or the shop where you purchased the product Notice for the customer in the countries applying EU Directives The manufacturer of this product is Sony Corporation 1 7 1 Konan Minato ku Tokyo 108 0075 Japan The Authorized Representative for EMC and product safety is Sony Deutschland GmbH Hedelfinger Strasse 61 70327 Stuttgart Germany For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents Precautions On power sources AC power cord must be changed only at a qualified service shop The unit is not disconnected from the AC power source mains as long as it is connected to the wall outlet mains even if the unit itself has been turned off As the main plug is used to disconnect the unit from
69. deo file sound may skip or not match the pictures on the TV screen The system cannot play some DivX video files that are longer than 3 hours Depending on the DivX video file the picture may pause or be unclear In which case it is recommended that you create the file at a lower bit rate If the sound is still noisy MP3 is the recommended audio format Note however this system does not conform to WMA Windows Media Audio format for playing DivX files Because of the compression technology used for DivX video files it may take some time after you press D gt for the picture to appear Selecting a folder 1 Press DVD MENU A list of folders on the disc appears Only folders that contain DivX video files are listed FOLDER LIST SUMMER 2003 NEW YEAR S DAY MY FAVOURITES 2 Press 1 4 to select the folder you want to play 3 Press I gt The system starts playing the selected folder To select DivX video files see Selecting a DivX video file page 62 To go to the next or previous page Press e p 4e To turn off the display Press DVD MENU repeatedly To stop playback Press Bl sosiq BuiAe d 10 suonoung snoueA g 61 GB Selecting a DivX video file 1 After step 2 of Selecting a folder press G The list of files in the folder appears FILE LIST C MY FAVOURITES HAWAII 2004 VENUS 2 Press 7 to select a file and press The selected f
70. display in OSD under LANGUAGE SETUP page 91 The language for the sound track Multilingual tracks are not recorded on the DVD being played cannot be changed The DVD prohibits changing the language for the sound track The subtitle language cannot be Multilingual subtitles are not recorded on the DVD being played changed The DVD prohibits changing the subtitles The subtitles cannot be turned off The DVD prohibits turning off subtitles The angles cannot be changed Multi angles are not recorded on the DVD being played page 54 The DVD prohibits changing the angles A disc cannot be ejected and Contact your Sony dealer or local authorized Sony service facility LOCKED appears in the front panel display Data error appears on the TV screen The MP3 file JPEG image file DivX video file you want to play is when playing a DATA CD or DATA broken DVD Data is not MPEG 1 Audio Layer 3 data The JPEG image file format does not conform to DCF The JPEG image file has the extension JPG or JPEG but is not in JPEG format The file you want to play has the extension AVI or DIVX but is not in DivX format or is in DivX format but does not conform to a DivX Certified profiles The system does not work normally Disconnect the AC power cord mains lead from the wall outlet mains then reconnect after several minutes DEMO PLAY appears in the front Contact your Sony dealer or
71. e by pressing the numeric buttons and To search for a scene using the time code DVD VIDEO and DVD VR mode only 1 In Step 2 select TIME T playing time ofthe current title is selected 2 Press T changes to T 3 Input the time code using the numeric buttons For example to find the scene at 2 hours 10 minutes and 20 seconds after the beginning just press 2 1 0 2 0 2 10 20 4 Press Note You cannot search for a scene on a DVD R DVD RW using the time code Resuming Playback from the Point Where You Stopped the Disc Resume Play wa OE Ce X3 Ce When you stop the disc the system remembers the point where you pressed W and Resume appears in the front panel display As long as you do not remove the disc Resume Play will work even if the system is set to standby mode by pressing VO 1 While playing a disc press W to stop playback Resume appears in the front panel display 2 Press The system starts playback from the point where you stopped the disc in Step 1 Note Depending on where you stop the disc the system may not resume playback from exactly the same point The point where you stopped playing may be cleared when you eject the disc the system enters standby mode DATA CD DATA DVD only you change or reset the settings on the Setup Display you change the function by pressing FU
72. e system turns off automatically Before using the System Power Off function set the function for TV power For details refer to the operating instructions of the TV Depending on the status of the system e g while other than DVD or TV function or playing a CD the system may not turn off automatically Enjoying TV sound from the speakers in this system System Audio Control You can enjoy TV sound in this system by easy operation To use this function connect the system and the TV with an audio cord not supplied and an HDMI cable not supplied page 27 Depending on the TV when you set the system to the TV function the System Audio Control function is activated TV sound is output from the system speakers and the volume of the TV speakers is minimized automatically You can use the System Audio Control function as follows While you are watching the TV and the function of the system is switched to TV TV sound is output from the system speakers automatically You can control the system s volume by the remote of the TV If you turn the system off or set the function of the system to other than TV TV sound is output from the TV speakers You can also operate the System Audio Control function from the TV menu For details refer to the operating instructions of the TV f the TV is turned on before turning on the system TV sound will not be output for a moment
73. e with the Theatre Mode you can enjoy optimal image suited for movies and the sound is output from the system s speaker automatically by pressing THEATRE 914 q orpny EUJ9 X3 IIANGH 40 01 U0D a 71 Watching DVD by a single button press One Touch Play By only pressing ONE TOUCH PLAY the TV turns on the TV is set for DVD input mode and the system starts playing a disc automatically The One Touch Play also works when You insert the disc and gt appears in the front panel display You press DVD TOP MENU DVD MENU and P appears in the front panel display You select the DVD function by pressing FUNCTION and gt appears in the front panel display One Touch Play does not work when you press D gt The system and TV work as follows e g This system TV Turns on If not already Turns on If not already turned on turned on Switches to DVD Switches to HDMI input function l l Starts playing the disc and Minimizes sound level outputs the sound System Audio Control Make sure the HDMI connection is correct and set the CONTROL FOR HDMI to ON Depending on the TV the beginning of the content may not be played back Depending on the disc playback may take a while to start Turning the system off in sync with the TV System Power Off When you turn the TV off by using the POWER button on the TV s remote or TV I on the system s remote th
74. ect other microphones Rear of the control unit 0000 O00000 TI 0000 gt To ECM AC2 jack Calibration microphone 10 Press gt to select YES Note Make sure that the headphones are not connected to the surround amplifier page 74 You cannot operate following steps with the headphones connected Before AUTO CALIBRATION be sure that the surround amplifier turns on and you install the surround amplifier in the appropriate location If you install the surround amplifier in an improper location such as another room proper measurement will not be obtained 11 Press AUTO CALIBRATION starts Be quiet during the measurement Note Loud test sound is output when AUTO CALIBRATION starts You cannot turn the volume down Give consideration to children and neighbours Avoid being in the measurement area and making noise during the measurement which takes about 1 minute as it may interfere with measurement 1 2 Unplug the calibration microphone and press gt to select YES The environment of the room in which the system is installed may affect measurements If measurement fails follow the message then retry AUTO CALIBRATION 13 Press Quick Setup is finished All connections and setup operations are complete To quit the Quick Setup Press C9 DISPLAY in any Step If you cancel AUTO CALIBRATION
75. el frequency of the other wireless system s For details refer to the operating instructions of the other wireless system s 914 q orpny EUJ9 X3 IIAGH 40 01 U0D a 7968 6055 Other Operations Controlling the TV with the Supplied Remote By adjusting the remote signal you can control your TV with the supplied remote When you replace the batteries of the remote the code number may reset itself to the default SONY setting Reset the appropriate code number Preparing the remote for controlling the TV Press and hold TV I while entering your TV s manufacturer s code see the table using the numeric buttons Then release TV yo If you successfully set the manufacturer s code the TV button flashes twice slowly Ifthe setting is unsuccessful the TV button flashes five times quickly Code numbers of controllable TVs If more than one code number is listed try entering them one at a time until you find the code that works with your TV TV Manufacturer Code number SONY 501 default AIWA 501 AKAI 503 DAEWOO 503 506 515 544 FISHER 508 545 GENERAL 503 509 510 544 ELECTRIC GE GOLDSTAR LG 503 515 517 544 568 GRUNDIG 533 HITACHI 503 514 515 517 544 557 571 ITT 521 522 JVC 516 LOEWE 515 MAGNAVOX 503 515 517 518 544 566 MARANTZ 527 MITSUBISHI MGA 503 527 544 566 56
76. elector on your TV so that the signal from the system appears on the TV screen Press ENTER to run QUICK SETUP appears at the bottom of the TV screen If this message does not appear recall the Quick Setup display page 36 and perform again 346 Press without inserting a disc The Setup Display for selecting the language used in the on screen display appears on the TV screen LANGUAGE SETUP SUBTITLE ITALIANO ESPANOL NEDERLANDS DANSK SVENSKA Press 4 to select a language The system displays the menu and subtitles in the selected language Press The Setup Display for selecting the aspect ratio of the TV to be connected appears VIDEO SETUP TV TYPE PROGRESSIVE compo 4 3 OUTPUT 4 3 LETTER BOX PAUSE MODE 4 3 PAN SCAN Press to select the setting that matches your TV type E If you have a wide screen TV or a 4 3 standard TV with a wide screen mode 16 9 page 91 E if you have a 4 3 standard TV 4 3 LETTER BOX or 4 3 PAN SCAN page 91 Press Connect the calibration microphone to the ECM AC2 jack on the rear of the control unit Set up the calibration microphone at the ear level using a tripod etc not supplied The front of each speaker should face the calibration microphone and there should be no obstruction between the speakers and the calibration microphone Note The ECM AC2 jack is used for the supplied calibration microphone only Do not conn
77. er speakers are connected properly connection page 23 Check front Front speakers are not connected and surround and only one surround speaker is speaker connected Check that the speakers connection are connected properly page 23 Check Contact your Sony dealer or local subwoofer authorized Sony service facility connection sjueunsn py pue sBunm s pooueApy H 6965 9065 Using the Setup Display You can make various adjustments for items such as picture and sound Displayed items differ depending on the country model Playback settings stored in the disc take priority over the Setup Display settings and not all the functions described may work 1 Press FUNCTION repeatedly until DVD appears in the front panel display 2 Press DISPLAY when the system is in stop mode The Control Menu display appears on the TV screen Press 4 4 to select E SETUP then press gt The options for SETUP appear 4 Press t to select CUSTOM then press 5 The Setup Display appears 5 Press t to select the setup item then press 5 LANGUAGE SETUP page 91 VIDEO SETUP page 91 HDMI SETUP page 93 AUDIO SETUP page 94 SYSTEM SETUP page 95 SPEAKER SETUP page 96 Example VIDEO SETUP Selected item VIDEO SETUP TV TYPE PROGRESSIVE COMPONENT OUT 4 3 OUTPUT PAUSE MODE Setup items 6 Press 4 4 to select an item then press Q The
78. er to that of the S AIR main unit To set the ID of the S AIR main unit see To set the ID of the S AIR main unit page 75 To set the ID of the S AIR receiver refer to the operating instructions of the S AIR receiver When you are using another S AIR sub unit such as a surround amplifier do not change the ID of the S AIR main unit Set the ID of the S AIR receiver to the same ID as the S AIR main unit When you pair the S AIR main unit and another S AIR sub unit such as a surround amplifier by the pairing operation you need to perform the pairing operation between the S AIR main unit and the S AIR receiver For details see Identifying the S AIR main unit with a specific S AIR sub unit Pairing operation page 77 2 Select the desired function on the S AIR receiver The function changes in the same sequence as you press FUNCTION page 41 3 Adjust the volume on the S AIR receiver Note When the sound is other than 2 channel stereo multi channel sound is downmixed to 2 channel The sound of the S AIR receiver may be cut off by operation of the S AIR main unit Sound source is same with both the system and S AIR receiver To control the system from the S AIR receiver You can control the system from the S AIR receiver by using the following buttons Press Operation D gt H g Share the same operations on the H4 1i remote and control unit S AIR CH Change the function o
79. er unit 35 mm Rated impedance 10 ohms Dimensions approx 45 x 55 x 40 mm w h d Mass approx 0 07 kg Speaker cords 45mx2 3mx1 12mx 2 Subwoofer SA WSIS50 Speaker system 2 Way 2 Drivers Subwoofer speaker system Speaker unit 120 mm 160 mm Rated impedance 4 ohms Dimensions approx 190 x 450 x 472 mm w h d Mass approx 13 5 kg Power requirements 220 240 V AC 50 60 Hz Power consumption On 130 W Standby 0 3 W at the Power Saving mode Control unit HCD IS50 Dimensions approx 215 x 105 x 207 mm w h d Mass approx 3 0 kg Power output DIGITAL MEDIA PORT uoneuuoju jeuonippv E DC OUT 5 V 700 mA Surround amplifier TA SA100WR Amplifier section Stereo mode rated 80 W 80 W at 3 ohms 1 kHz 1 THD Surround mode reference RMS output power 143 W per channel at 3 ohms 1 kHz 10 THD Depending on the source there may be no sound output continued 111 112 Rated impedance 3 162 General Power requirements 220 240 V AC 50 60 Hz Power consumption On 50 W Dimensions approx 85 x 100 x 330 mm w h d including EZW RT10 85 x 100 x 345 mm w h d including speaker cord cover and speaker cord holder 1 7 kg including speaker cord cover and speaker cord holder Wireless transceiver EZW RT10 Communication system S AIR Specification Mass approx version 1 0 Output 12 0 mW Frequency band 2 4000 GHz 2 4835 GHz Modulation m
80. ess DISPLAY repeatedly Each time you press DISPLAY while playing the disc the front panel display changes Some displayed items may disappear after a few seconds E DVD VIDEO DVD VR CD Playing time of the current title 2 Remaining time of the current title Playing time of the current chapter Remaining time of the current chapter Disc name 6 Title and chapter E VIDEO CD without PBC functions CD CD Playing time of the current track 2 Remaining time of the current track 3 Playing time of the disc Remaining time of the disc 5 Track name Track and index d VIDEO CD only E Super VCD Playing time of the current track 2 Track text 3 Track and index number W DATA CD MP3 file or DATA DVD MP3 file Playing time and current track number 2 Track file name gt If an MP3 file has the ID3 tag the system will display a folder name track file name from the ID3 tag information The system can support ID3 version 1 0 1 1 2 2 2 3 ID3 version 2 2 2 3 tag information display has priority when both ID3 version 1 0 1 1 and version 2 2 2 3 tags are used for a single MP3 file E DATA CD DivX video file DATA DVD DivX video file Playing time of the current file 2 Current file name Current album and file number The system can only display the first level of the DVD CD text such as the disc name or title fa file name of the MP3 file cannot be displayed will
81. ethod DSSS Power requirements DC 3 3 V 350 mA Dimensions approx 50 x 13 x 60 mm w h d Mass approx 24g Wireless transmitter EZW T100 Communication system S AIR Specification version 1 0 Output 12 0 mW Frequency band 2 4000 GHz 2 4835 GHz Modulation method DSSS Power requirements DC 4 V 550 mA DC 5 V 15 mA 52x 24 x 95 mm max 77 x 24 x 95 mm w h d Mass approx 6lg Dimensions approx Design and specifications are subject to change without notice Standby power consumption 0 3 W Halogenated flame retardants are not used in the printed wiring boards Over 85 power efficiency of amplifier block is achieved with the full digital amplifier S master Glossary Digital Cinema Auto Calibration Digital Cinema Auto Calibration was developed by Sony to automatically measure and adjust the speaker settings to your listening environment in a short period of time Dolby Digital This movie theatre sound format is more advanced than Dolby Surround Pro Logic In this format the surround speakers output stereo sound with an expanded frequency range and a subwoofer channel for deep bass is independently provided This format is also called 5 1 with the subwoofer channel designed as the 0 1 channel since it functions only when a deep bass effect is needed AII six channels in this format are recorded separately for superior channel separation Furthermore since all the signals are proce
82. f the system For details refer to the operating instructions of the S AIR receiver Enjoying the S AIR receiver while the S AIR main unit is in standby mode For the S AIR receiver not supplied You can enjoy the S AIR receiver while the S AIR main unit is in standby mode by setting S AIR STBY to ON 1 Press svsrEM MENU 2 Press t repeatedly until S AIR STBY appears in the front panel display then press or 2 3 Press 1 4 to select the desired setting ON You can enjoy the S AIR receiver while the S AIR main unit is in standby mode or turned on OFF You cannot enjoy the S AIR receiver while the S AIR main unit is in standby mode 4 Press 3 The setting is made 5 Press SYSTEM MENU The system menu turns off Note When you set S AIR STBY to ON the power consumption during the standby mode increases When you turn the system off while S AIR STBY is set to ON S AIR flashes when sound transmission between the S AIR main unit and S AIR receiver is not established or lights up when sound transmission between the S AIR main unit and S AIR receiver is established in the front panel display When the wireless transmitter is not inserted in the S AIR main unit you cannot set S AIR STBY S AIR STBY is set to OFF automatically when the wireless transmitter is removed from the S AIR main unit When you turn the system off while S A
83. for changing slides during a slide show Ez MODE MUSIC IMAGE page 59 You can select the data type MP3 file JPEG image file or both to be played when playing a DATA CD DATA DVD para co These items are not listed when playing a DATA CD DATA DVD with DivX video file The Control Menu icon indicator lights up in yellow when you select any item except OFF PROGRAM SHUFFLE and REPEAT only The ORIGINAL PLAY LIST indicator lights up in yellow when you select PLAY LIST default setting uoneuuojuj jeuonippv li 12365 124 Index Numerics 16 9 91 4 3 LETTER BOX 91 4 3 OUTPUT 92 4 3 PAN SCAN 91 5 1 Channel Surround 51 A A V SYNC 55 ANGLE 54 ATTENUATE 42 AUDIO 50 AUDIO HDMI 94 AUDIO DRC 95 AUDIO SETUP 94 AUTO CALIBRATION 88 94 BACKGROUND 96 BASS 66 Batteries 11 C CHAPTER 44 CONNECTION 96 Control for HDMI 70 93 Control Menu Display 121 Control unit 115 116 CUSTOM 90 99 D D C A C Digital Cinema Auto Calibration 88 94 112 DATA CD 6 DATA DVD 6 Decoding mode 63 DIGITAL IN 95 DIGITAL MEDIA PORT 28 73 DIMMER 84 DISPLAY 52 69 DISTANCE 97 DivX 60 96 Dolby Digital 51 112 Dolby Pro Logic II 112 DTS 113 DUAL MONO 82 DVD s menu 49 E EFFECT 60 F FM Mode 68 Front panel 115 Front panel display 84 117 H HDMI high definition multimedia interface 113 HDMI SETUP 93 HDMI YCBCR RGB HDMI 93 ILLUMINATION MODE 85
84. guages Depending on the type of disc being played the system can only display a limited number of characters Also depending on the disc not all text characters will be displayed Checking the play information of the disc To check DVD CD text Press DISPLAY repeatedly during playback to display text recorded in the DVD CD The DVD CD text appears on the TV screen only when text is recorded in the disc You cannot change the text If the disc does not contain text NO TEXT appears Dvorak Tchaikovsky NedPho Kreizberg Adagio Allegro molto To check DATA CD DATA DVD MP3 file DivX video file text By pressing DISPLAY while playing MP3 files or DivX video files on a DATA CD DATA DVD you can display the name of the folder MP3 file DivX video file and the audio bit rate the amount of data per second of the current audio on your TV screen Bit rate 0 13 192k MP3 T 002 Remixes Soul Survivor rap versio Folder name MP3 file DivX video file name Appears when playing an MP3 file ona DATA CD DATA DVD playing a DivX video file that contains MP3 audio signals on a DATA CD DATA DVD If an MP3 file has the ID3 tag the system will display a folder name track file name from the ID3 tag information The system can support ID3 version 1 0 1 1 2 2 2 3 ID3 version 2 2 2 3 tag information display has priority when both ID3 version 1 0 1
85. he system will play any data with the extension MP3 JPG or JPEG even if they are not in MP3 or JPEG format Playing these data may generate a loud noise which could damage your speaker system The system does not conform to audio in MP3PRO format The system can recognize up to 200 folders and will not play any folders beyond the 200th Depending on the folder configuration the number of folders that can be recognized by the system may decrease The system can recognize up to 150 MP3 files JPEG image files in a folder The system may take longer time to playback when progressing to the following folder or jumping to other folder The system may not play certain types of JPEG image files e g a JPEG image file that is less than 8 width x 8 height Selecting an MP3 file or folder Load a DATA CD or DATA DVD 2 Press DVD MENU The folders recorded on the DATA CD or DATA DVD appear on the TV screen When a folder is being played its title is shaded FOLDER LIST 01 Let s Talk About Love 1985 02 1st Album 1986 03 In the Middle of Nowhere 1986 04 Ready for Romance 1986 05 In the Garden of Venus 1987 06 Romantic Warriors 1987 07 Back for Good 1988 08 Alone 1999 Y 3 Press V to select a folder E To play MP3 files in a folder Press to start playing the selected folder E To select an MP3 file Press A list of files contained in the folder a
86. heck the speaker connections Depending on the disc the sound may come from the center speaker only No sound is heard from the center speaker Check the speaker connections and settings pages 23 96 Check the DEC MODE setting page 63 Depending on the source the effect of the center speaker may be less noticeable A2 channel source is being played Symptom Remedy No sound or only a very low level sound is heard from the surround speakers Check the speaker connections and settings pages 23 96 Check the DEC MODE setting page 63 Depending on the source the effect of the surround speakers may be less noticeable Wireless setting of the speaker is not correct A 2 channel source is being played The beginning of the sound is cut off Set the Sound mode to other than AUTO page 65 Set the decoding mode to other than A F D MULTI page 63 No sound is heard or sound is cut off The S AIR main unit and or the surround amplifier is installed in a place such as on a metal shelf Wireless LANs a microwave oven and Bluetooth applications etc are pl aced near the surround amplifier Move away the other components from the surround amplifier or turn off the other components Operation Symptom Remedy Radio stations cannot be tuned in Check that the antenna aerial is connected securely Adjust the antenna
87. ile starts playing To go to the next or previous page Press e 4 e To return to the previous display Press gt RETURN To stop playback Press Bl To play the next or previous DivX video file without turning on the above file list You can select the next or previous DivX video file in the same folder by pressing PP 1 H You can also select the first file of the next folder by pressing PI during playback of the last file of the current folder Note that you cannot return to the previous folder by pressing H 4 To return to the previous folder select it from the folder list Tip z number of viewing times is preset you can play the DivX video files as many times as the preset number The following occurrences are counted when the system is turned off when another file is played Playing a VIDE0 GD with PBC Functions Ver 2 0 PBC Playback VIDEO cn With PBC Playback Control functions you can enjoy simple interactive operations search functions and other such operations PBC playback allows you to play a VIDEO CD interactively by following the menu on the TV screen 1 start playing a VIDEO CD with PBC functions The menu for your selection appears on the TV screen 2 Select the item number you want using the numeric buttons 3 Press Q 4 Follow the instructions in the menu for interactive operations Refer to the operating instructions supplied with the disc as the operat
88. ing on the DVD VIDEO you may not be able to change the subtitles even if multilingual subtitles are recorded on the disc You also may not be able to turn them off You can change the subtitles if the DivX video file has an AVI or DivX extension and contains subtitle information within the same file Adjusting the Delay Between the Picture and Sound A V SYNC I GE UJ When the sound does not match the pictures on the TV screen you can adjust the delay between the picture and sound 1 Press SYSTEM MENU 2 Press 4 4 repeatedly until A V SYNC appears in the front panel display then press or gt 3 Press to select a setting LONG adjusts the difference between picture and sound by 130 msec SHORT adjusts the difference between picture and sound by 70 msec OFF does not adjust 4 Press The setting is made D press SYSTEM MENU The system menu turns off Note Depending on the input stream A V SYNC may not be effective sosiq BuiAe d 10 suonoung snoueA 5568 5655 Playing MP3 Files JPEG Image Files You can play the MP3 files or JPEG image files which have the extension MP3 MP3 file or JPG JPEG JPEG image file which conform to the DCF image file format Design rule for Camera File system Image standards for digital cameras regulated by Japan Electronics and Information Technology Industries Association JEITA T
89. ing procedure may differ depending on the VIDEO CD To go back to the menu Press gt RETURN Note Depending on the VIDEO CD Press ENTER in Step 3 may appear as Press SELECT in the operating instructions supplied with the disc In this case press gt To play without using the PBC function press K lt PPI or the numeric buttons while the system is in stop mode to select a track then press E gt or The system starts playback You cannot play still pictures such as a menu To return to PBC playback press li twice then press gt Sound Adjustments Enjoying Surround Sound by Using Decoding Mode co u DII a Oe Oo You can enjoy surround sound simply by selecting one of the system s pre programmed decoding mode They bring exciting and powerful sound of movie theaters into your home 1 Press SYSTEM MENU 4 4 92 SYSTEM MENU 2 Press t repeatedly until DEC MODE appears in the front panel display then press or 2 3 Press 1 4 repeatedly until the decoding mode you want appears in the front panel display Display Decoding mode Effect A F D STD AUTO FORMAT Presents sound as it was recorded encoded DIRECT Depending on the source the speakers that output sound will vary STANDARD A F D MULTI AUTO FORMAT 2 channel source Sound that is recorded in 2 channel front left and DIRECT MULTI right channel is also assigned to the surround left and right cha
90. ished sound transmission is not established e g the indicator of the S AIR sub unit does the following Turns off Flashes Turns red If you use another S AIR main unit place it more than 8 m away from this S AIR main unit Confirm the ID of the S AIR main unit and S AIR sub unit page 75 You performed pairing the S AIR main unit and another S AIR sub unit Perform pairing of the desired S AIR sub unit page 77 The S AIR main unit is paired to another S AIR sub unit Cancel pairing Install the S AIR main unit and S AIR sub unit away from other wireless products Stop using another wireless product The S AIR sub unit is turned off Make sure the AC power cord mains lead is connected and turn on the S AIR sub unit No sound is heard from the S AIR sub unit If you use another S AIR main unit place it more than 8 m away from this S AIR main unit Confirm the ID of the S AIR main unit and S AIR sub unit page 75 Confirm the pairing setting page 77 Install the S AIR main unit and S AIR sub unit closer together Avoid use of equipment that generates electromagnetic energy such as a microwave oven Install the S AIR main unit and S AIR sub unit away from other wireless products Stop using another wireless product Change the RF CHANGE setting page 79 Change the ID settings of the S AIR main unit and S AIR sub unit Turn off the system and S AIR sub unit then turn on them
91. items using DVD MENU 1 Press DVD TOP MENU or DVD MENU The disc s menu appears on the TV screen The contents of the menu vary depending on the disc 2 Press V or the numeric buttons to select the item you want to play or change 3 Press To display the DVD s menu on the Control Menu display 1 Press DISPLAY during playback The Control Menu display appears on the TV screen 2 Press to select KEJ Disc MENU then press The options for DISC MENU appear 3 Press t to select MENU or TOP MENU 4 Press To turn off the Control Menu display Press DISPLAY repeatedly until the Control Menu display is turned off sosiq BuiAe d 10 suonounJ snoueA g ages 5068 Changing the Sound When the system is playing a DVD VIDEO or DATA CD DATA DVD DivX video file recorded in multiple audio formats PCM Dolby Digital MPEG audio or DTS you can change the audio format If the DVD VIDEO is recorded with multilingual tracks you can also change the language With a VIDEO CD CD DATA CD or DATA DVD you can select the sound from the right or left channel and listen to the sound of the selected channel through both the right and left speakers Press AUDIO repeatedly during playback to select the desired audio signal E DVD VIDEO Depending on the DVD VIDEO the choice of language varies When 4 digits are displayed they indicate a language code See Language Code List
92. ker cords For details on changing the speaker cords see step 2 to 4 of Installing the speakers to the wall below Contact a screw shop or installer regarding the wall material or screws to be used Use screws that are suitable for the wall material and strength As a plaster board wall is especially fragile attach the screws securely to a beam and fasten them to the wall Install the speakers on a vertical and flat wall where reinforcement is applied Sony is not responsible for accident or damage caused by improper installation insufficient wall strength or improper screw installation natural calamity etc 1 Prepare screws not supplied that are suitable for the holes of the bracket 2 Secure the bracket to the wall using hole 1 To prevent the speaker from rotating use the hole 2 too continued 15 3 Remove the rear cap using the wrench supplied and remove the speaker pedestal using a screwdriver not supplied Wrench supplied o o 2 LI S 7 D amp E When the lever is down the When the lever is up the speaker cords are locked speaker cords can be removed LIS Lo at il D Wt 5 Thread the speaker cords through hole 1658 6 Reconnect the detached speaker cords matching to the appropriate speaker terminals 1 and then push the lever down completely 2 G i E 5 O c o at a f it is difficult to push the leve
93. ker terminals to and to If the cords are reversed the sound will lack bass and may be distorted 18 Step 2 Connecting the System See the connection diagram below and read the additional information from to on the following pages wa Be sure to make connection securely to avoid hum and noise When you connect another component with a volume control turn up the volume of the other components to a level where sound is not distorted O 1 E e 2 2i a You can connect your surround speakers in 2 different ways Connect surround speakers to S AIR surround amplifier wireless connection Connect surround speakers to subwoofer wired connection Sony recommends you to use wireless connection for this system continued 196 o o 2 LE 7 D 5 E a Connect surround speakers to S AIR surround amplifier wireless connection DIGITAL MEDIA PORT adapter Portable audio source VCR digital satellite receiver or PlayStation etc FM wire antenna Front of the control unit ora Bottom of the subwoofer NI Wireless transmitter Rear of the AC power cord mains lead subwoofer Front Center speaker R speaker Front speaker L FE 9 Wireless transceiver Surround amplifier 2 Surround speaker L 2 Surround speaker R AC power cord
94. lace the subwoofer under a desk or in a cabinet etc When you change the position of the speakers Sony recommends that you change the settings For details see Calibrating the Appropriate Settings Automatically page 88 Do not place the subwoofer back of the obstruction such as TV etc Middle range sound will fall continued 1368 D o E LE S 7 D amp E Note on handling the subwoofer Do not place your hand into the slit of the subwoofer when lifting it The speaker driver may be damaged When lifting hold the bottom of the subwoofer Subwoofer Slits Do not hold the EZW T100 slot when lifting the subwoofer Do not push the top of the subwoofer where the speaker unit is installed Speaker unit EZW T100 slot 146 Installing the speakers on the wall Before installing the speakers on the wall you need to decide which surround speakers connection you want You can connect your surround speakers in 2 different ways Connect surround speakers to S AIR surround amplifier wireless connection Connect surround speakers to subwoofer wired connection Sony recommends you to use wireless connection for this system For details see Step 2 Connecting the System page 19 O Ed gt e O m o ei The surround speakers supplied are for wireless connection Ifyou want to change to wired connection you need to change the surround spea
95. li 1376 Dutch 1379 Norwegian 1393 Occitan 1403 Afan Oromo 1408 Oriya 1417 Punjabi 1428 Polish 1435 Pashto Pushto 1436 Portuguese 1463 Quechua 1481 Rhaeto Romance 1482 Kirundi 1483 Romanian 1489 Russian 1491 Kinyarwanda 1495 Sanskrit 1498 Sindhi 1501 Sangho 1502 Serbo Croatian 1503 Singhalese 1505 Slovak 1506 Slovenian 1507 Samoan 1508 Shona 1509 Somali 1511 Albanian 1512 Serbian 1513 Siswati 1514 Sesotho 1515 Sundanese 1516 Swedish 1517 Swahili 1521 Tamil 1525 Telugu 1527 Tajik 1528 Thai 1529 Tigrinya 1531 Turkmen 1532 Tagalog 1534 Setswana 1535 Tonga 1538 Turkish 1539 Tsonga 1540 Tatar 1543 Twi 1557 Ukrainian 1564 Urdu 1572 Uzbek 1581 Vietnamese 1587 Volap k 1613 Wolof 1632 Xhosa 1665 Yoruba 1684 Chinese 1697 Zulu 1703 Not specified Parental Control Area Code List Code Area Code Area Code Area Code Area 2044 Argentina 2047 Australia 2046 Austria 2057 Belgium 2070 Brazil 2079 Canada 2090 Chile 2092 China 2115 Denmark 2165 Finland 2174 France 2109 Germany 2248 India 2238 Indonesia 2254 Italy 2276 Japan 2304 Korea 2363 Malaysia 2362 Mexico 2376 Netherlands 2390 New Zealand 2379 Norway 2427 Pakistan 2424 Philippines 2436 Portugal 2489 Russia 2501 Singapore 2149 Spain 2499 Sweden 2086 Switzerland 2528 Thailand 2184 United Kingdom Index to Parts and Controls For more information refer to the pages indicated in parentheses Control unit fr
96. lifier 1 Make sure that the SURROUND SELECTOR switch of the surround amplifier is set to SURROUND 2 Set the S AIR ID switch of the surround amplifier to match the ID A B or C of the S AIR main unit 3 Press POWER on the surround amplifier When sound transmission is established the POWER ON LINE indicator of the surround amplifier turns green For details of the POWER ON LINE indicator see To check the transmission status page 32 continued 914 q orpny EUJ9 X3 IIANGH 40 01 U0D a 75 GB 1698 To set the ID of the S AIR receiver not supplied Refer to the operating instructions of the S AIR receiver Note It is easy to set the same ID for the S AIR main unit and S AIR sub unit to establish sound transmission However neighbours may also receive your system s sound if IDs are the same or you may receive the sound from neighbours To prevent this you can identify the S AIR main unit with a specific S AIR sub unit by performing the pairing operation page 77 Enjoying the system s sound in another room For the S AIR receiver not supplied You can enjoy the system s sound by using the S AIR receiver The S AIR receiver can be installed anywhere regardless of the location of the S AIR main unit for enjoying the system s sound in another room For details of the S AIR receiver refer to the operating instructions of the S AIR receiver 1 Set the ID of the S AIR receiv
97. locked or replaced with different scenes You can set the playback restriction by registering a password When you set the PARENTAL CONTROL function to on you need to enter the password to play restricted discs 1 Press FUNCTION repeatedly until DVD appears in the front panel display 2 Press DISPLAY while the system is in stop mode The Control Menu display appears on the TV screen 3 Press to select lr g SETUP then press gt The options for SETUP appear 4 Press 1 4 to select CUSTOM then press gt The Setup Display appears D Press 4 to select SYSTEM SETUP then press gt The options for SYSTEM SETUP appear 6 Press 1 4 to select PARENTAL CONTROL then press E if you have not entered a password The display for registering a new password appears PARENTAL CONTROL Enter a new 4 digit password then press ENTER Enter a 4 digit password using the numeric buttons then press The display for confirming the password appears W When you have already registered a password The display for entering the password appears Enter or re enter your 4 digit password using the numeric buttons then press The display for setting the playback limitation level appears PARENTAL CONTROL LEVEL OFF STANDARD USA CHANGE PASSWORD Press to select STANDARD then press 5 The selection items for STANDARD are displayed Press t
98. mage files or JPEG image files of 3 000 000 pixels or more Duration of interval depends on the JPEG RESOLUTION setting in HDMI SETUP page 94 sosiq BulAe g 10 suoll9unjJ snoueA g 5968 608 Selecting an effect for JPEG image files in the slide show 1 Press DISPLAY twice The Control Menu display appears on the TV screen 2 Press 1 to select MEM EFFECT then press The options for EFFECT appear 3 Press t to select a setting e MODEI The JPEG image file sweeps in from top to bottom MODE2 The JPEG image file stretches out from left to right of the TV screen MODE3 The JPEG image file stretches out from the center of the TV screen MODE4 The JPEG image file randomly cycle through the effects MODES The next JPEG image file slides over the previous image OFF Off 4 Press wa The EFFECT setting is not effective when you set JPEG RESOLUTION in HDMI SETUP to 1920 x10801 HD _ or 1920 x1080i HD page 94 Enjoying DivX Videos CS Dr About DivX video files DivX is a video file compression technology developed by DivX Inc This product is an official DivX Certified product You can play a DATA CD or DATA DVD that contains DivX video files A DATA CD or DATA DVD that the system can play Playback ofa DATA CD CD ROM CD R CD RW or DATA DVD DVD ROM DVD R DVD RW DVD R DVD RW on this system is subject to cer
99. mains lead is connected securely Press I after STANDBY disappear from the front panel display After connecting the AC power cord mains lead wait about 20 seconds before turning on the power by pressing l C5 If PROTECTOR and PUSH POWER appear alternately in the front panel display Press I C to turn off the system and check the following items after STANDBY disappears Are the and speaker cords short circuited Are you using only the specified speakers Is anything blocking the ventilation slots of the system Check the above items and fix any problems After STANDBY disappears wait about 20 seconds before turning on the power by pressing V5 If the cause of the problem cannot be found even after checking all the above items consult your nearest Sony dealer Picture Symptom Remedy There is no picture The video connecting cords are not connected securely The video connecting cords are damaged The control unit is not connected to the correct TV input jack page 26 The video input on the TV is not set so that you can view pictures from the system Check the output method on your system page 36 You have set progressive format but your TV cannot accept the signal in progressive format In this case return the setting to interlace format the default setting page 37 Even if your TV is compatible with progressive format 525p signals the image may
100. message then select YES to retry Note While the Auto Calibration function works do not turn off the power do not press any button do not change the volume do not change the function do not insert or eject a disc do not connect the headphones to the surround amplifier do not disconnect the calibration microphone When change the surround speakers from wireless connection to wired connection or vice versa use D C A C function to adjust the sound setting You can check the distance between the listening position and each speaker See page 96 About error messages for the auto calibration Ifthe following message appears during AUTO CALIBRATION check Symptoms and remedies and retry the auto calibration Error Symptoms and remedies message Check No channel sound can be detected calibration mic Check that the calibration connection microphone is connected properly If the calibration microphone is connected properly the calibration microphone or calibration microphone cord may be damaged Micinputlevel The calibration microphone or overloaded system may be damaged Contact your Sony dealer or local authorized Sony service facility Check front Front speakers are not connected speaker Check that the front speakers are connection connected properly page 23 Check Only one surround speaker is surround connected Check that the surround speak
101. n select ON in step 3 and press To turn off the Control Menu display Press DISPLAY repeatedly until the Control Menu display is turned off To change or cancel a program 1 Follow steps 1 to 3 of Creating Your Own Program 2 Press to select the program number of the track you want to change or cancel If you want to delete the track from the program press CLEAR 3 Follow step 5 for new programming To cancel a program select under T then press gt To cancel all of the tracks in the programmed order 1 Follow steps 1 to 3 of Creating Your Own Program 2 Press and select ALL CLEAR 3 Press Note When you press CLEAR to return to normal play Shuffle Play and Repeat Play are also canceled Playing in Random Order Shuffle Play 2 ICIN Oe ITT You can play the contents on a disc in random order Subsequent Shuffle Play may produce a different playing order Note Same song may be played repeatedly when you are playing MP3 files 1 Press c DISPLAY during playback The Control Menu display appears on the TV screen 2 Press 1 to select SHUFFLE then press The options for SHUFFLE appear 3 Press t to select the item to be shuffled E VIDEO CD CD OFF Off TRACK You can shuffle tracks on the disc B During Program Play OFF Off ON You can shuffle tracks selected in Program Play E DATA CD except for DivX vide
102. n is front panel display and the poor In these cases check radio reception and set the volume again volume of the unit becomes minimum 109 110 Self diagnosis Function When letters numbers appear in the display When the self diagnosis function is activated to prevent the system from malfunctioning a 5 character service number e g C 13 50 with a combination of a letter and 4 digits appears on the TV screen or front panel display In this case check the following table AELITA C 13 50 IIIASN First 3 Cause and or corrective action characters of the service number C13 The disc is dirty gt Clean the disc with a soft cloth page 101 The disc is a format that the system cannot play C31 The disc is not inserted correctly gt Restart the system then re insert the disc correctly EXX To prevent a malfunction the xx is a number system has performed the self diagnosis function gt Contact your nearest Sony dealer or local authorized Sony service facility and give the 5 character service number Example E 61 10 When displaying the version number on the TV screen When you turn on the system the version number VER X XX X is a number may appear on the TV screen Although this is not a malfunction and for Sony service use only normal system operation will not be possible Turn off the system and then turn on the system again to operate
103. n is available only when the S AIR transmitter is inserted into the S AIR main unit E AUTO CALIBRATION You can calibrate the appropriate settings automatically For details see Calibrating the Appropriate Settings Automatically page 88 W DIGITAL IN You can assign a digital sound input corresponding with the function TV and SAT CABLE TV OPT Optical audio input signals are SAT CABLE assigned to TV function COAX coaxial audio input signals are assigned to SAT CABLE function TV COAX Coaxial audio input signals are SAT CABLE assigned to TV function optical OPT audio input signals are assigned to SAT CABLE function E AUDIO DRC DVD VIDEO only You can compress the dynamic range of the sound track AUDIO DRC is useful for watching movies at low volume late at night OFF No compression of dynamic range STANDARD The system reproduces the sound track with the kind of dynamic range that the recording engineer intended MAX The system compresses dynamic range fully wa AUDIO DRC works only for Dolby Digital E TRACK SELECTION DVD VIDEO only You can give the sound track which contains the highest number of channels priority when you play a DVD VIDEO on which multiple audio formats PCM DTS Dolby Digital or MPEG audio are recorded OFF Off AUTO The system selects the sound track automatically accordi
104. n of the system and TV manually Note Displayed items vary depending on the country model 1 Make sure that the system and the TV are connected with an HDMI cable 2 Turn on the TV and press l 5 to turn on the system 3 Switch the input selector on your TV so thatthe signal from the system through the HDMI input appears on the TV screen 4 Setthe Control for HDMI function of the system and TV For details of the setting of the system see the following steps For details of the setting of the TV refer to the operating instructions of the TV depending on the TV the default setting of the Control for HDMI function is set to off To set the CONTROL FOR HDMI function to on off 1 Press FUNCTION repeatedly until DVD appears in the front panel display 2 Press DISPLAY while the system is in stop mode The Control Menu display appears on the TV screen 3 Press 4 4 to select EEN SETUP then press 3 The options for SETUP appear 4 Press 4 4 to select CUSTOM then press 5 The Setup Display appears 5 Press 77 to select HDMI SETUP then press G gt The options for HDMI SETUP appear 6 Press 1 4 to select CONTROL FOR HDMI then press 1 Press 1 4 to select the setting then press OFF Off ON On Note When Please verify the HDMI connection appears make sure the HDMI connection is correct Using the Theatre Mode Theatre Mode If your TV is compatibl
105. nals Interlace format Interlaced scanning The Interlace format is the NTSC standard method for displaying TV images at 30 frames per second Each frame is scanned twice alternately between the even numbered scanning lines and then odd numbered scanning lines at 60 times per second Parental Control A DVD function to limit playback of the disc by users of a predetermined age according to the limitation level in each country The limitation varies from disc to disc when it is activated playback is completely prohibited violent scenes are skipped or replaced with other scenes etc Progressive format Sequential scanning In contrast to the Interlace format the progressive format can reproduce 50 60 frames per second by reproducing all scanning lines 525 lines for the NTSC system The overall picture quality increases and still images text and horizontal lines appear sharper S AIR Sony Audio Interactive Radio frequency Recent times have seen the rapid spread of DVD media Digital Broadcasting and other high quality media To ensure that the subtle nuances of these high quality media are transmitted with no deterioration Sony has developed a technology called S AIR for the radio transmission of digital audio signals with no compression and has incorporated this technology into the EZW RT10 EZW T100 This technology transfers digital audio signals with no compression using the 2 4 GHz band range of I
106. ng the subwoofer efficiently To reinforce the bass sound place the subwoofer possible close to a wall Close to a wall Note If the subwoofer is to be placed ahead of the front speaker the distance should be less than 0 5 m You may not get the bass sound efficiently when the subwoofer is placed outside 8 You need to adjust the setting of the distance from the listening position TV etc peyeys Dunes Do not place objects on the top of the subwoofer where the speaker unit is installed Q e Do not set the speakers in an inclined position Do not place the speakers in locations that are Extremely hot or cold Dusty or dirty Very humid Subject to vibrations Subject to direct sunlight Use caution when placing the speakers and or speaker stands not supplied that are attached to the speakers on a specially treated waxed oiled polished etc floor as staining or discolouration may result When cleaning use a soft cloth such as a cleaning cloth for glasses Do not use any type of abrasive pad scouring powder or solvent such as alcohol or benzine mage distortion on the TV screen may occur depending on the location of the subwoofer In this case place the subwoofer away from the TV Do not p
107. ng to the priority Note When you set the item to AUTO the language may change The TRACK SELECTION setting has higher priority than the AUDIO settings in LANGUAGE SETUP page 91 Depending on the disc this function may not work If PCM DTS Dolby Digital sound and MPEG audio have the same number of channels the system selects PCM DTS Dolby Digital sound and MPEG audio in this order Other Settings SYSTEM SETUP SYSTEM SETUP SCREEN SAVER BACKGROUND JACKET PICTURI PARENTAL CONTROL DivX Registration Code gt MULTI DISC RESUME ON RESET E SCREEN SAVER You can reduce the display device damages ghosting Press any button e g E gt button to cancel the screen saver ON The screen saver image appears when you leave the system in pause or stop mode for about 15 minutes or when you play back a CD DATA CD MP3 file or DATA DVD MP3 file for more than 15 minutes OFF Off continued sjueunsn py pue sB5uim s pesueapy H 0565 9665 E BACKGROUND You can select the background colour or picture on the TV screen in stop mode or while playing a CD DATA CD MP3 file or DATA DVD MP3 file JACKET The jacket picture still picture PICTURE appears but only when the jacket pP y J picture is already recorded on the disc CD EXTRA etc If the disc does not contain a jacket picture the GRAPHICS picture appears
108. nnel This mode outputs sound from the front left and right speakers surround left and right speakers and subwoofer The center speaker does not output any sound Multi channel source Depending on the source speakers that output the sound will vary PLIT MOVIE Dolby Pro Logic II Performs Pro Logic II movie mode decoding to the input signal and MOVIE produces five full bandwidth output channels from 2 channel sources This setting is ideal for watching videos of overdubbed or old movies This mode outputs sound from all the speakers and subwoofer Sound may not be output from all speakers depending on the source continued sjueunsn py punos 63 GB 645 Display Decoding mode Effect PLIT MUSIC Dolby Pro Logic II Performs Pro Logic II music mode decoding to the input signal and MUSIC produces five full bandwidth output channels from 2 channel sources This setting is ideal for normal stereo sources such as a CD This mode outputs sound from all the speakers and subwoofer Sound may not be output from all speakers depending on the source 2CH STEREO 2 CHANNEL Outputs the sound from the front left and right speakers and STEREO subwoofer Multi channel surround formats are downmixed to 2 channels HP THEATER HEADPHONE Outputs the sound as surround from headphones left and right THEATER HP 2CH HEADPHONE Outputs the sound from headphones left and right Multi channel 2 CHANNEL surr
109. nsmission is established the PAIRING indicator of the surround amplifier turns red and the confirmation display appears To press PAIRING on the rear panel of the surround amplifier a slim instrument such as a paper clip can be used W For the S AIR receiver Refer to the operating instructions of the S AIR receiver When sound transmission is established the confirmation display appears Note Perform the pairing within several minutes after step 10 If you do not the pairing is canceled automatically and the confirmation display appears To perform pairing select YES To return to the previous display select NO 1 2 Press 2 to select the next operation W To finish pairing Select NO then press W To perform pairing of another S AIR sub unit Select YES then press G f you perform the pairing operation between the S AIR main unit and another S AIR sub unit page 77 sound transmission established by ID is canceled When you perform pairing PAIRING appears beside ID on the display for selecting ID To cancel pairing Perform the ID setting of the S AIR main unit according to the procedure of To set the ID of the S AIR main unit page 75 If you select a new ID you can select the same ID as before pairing is canceled If sound transmission is unstable For the surround amplifier supplied For the S AIR receiver not supplied If you use multiple wireless system
110. o adjust LEVEL FRONT and LEVEL SURROUND The test tone is not emitted from the speakers OFF ON The test tone is emitted from each speaker in sequence while adjusting level When you select one of the SPEAKER SETUP items the test tone is emitted from each speaker in sequence Adjusting the speaker level by using the test tone 1 Press DISPLAY when the system is in stop mode The Control Menu display appears 2 Press to select EUR SETUP then press 5 The options for SETUP appear 3 Press t to select CUSTOM then press 5 The Setup Display appears 4 Press V repeatedly to select SPEAKER SETUP then press or gt Press V repeatedly to select TEST TONE then press or gt 6 Press t repeatedly to select ON then press gt You will hear the test tone from each speaker in sequence 7 Press gt to adjust the value of LEVEL FRONT or LEVEL SURROUND The test tone is emitted from only the speaker which you are adjusting 8 Press when you have finished making adjustments 9 Press V repeatedly to select TEST TONE then press 1 0 Press t repeatedly to select OFF then press gt The test tone signals are not output from the HDMI OUT jack To adjust the volume of all the speakers at one time press VOLUME To return to the default setting when changing a setting select the item then press CLEAR Note
111. o file DATA DVD except for DivX video file OFF Off ON MUSIC You can shuffle MP3 files in the folder on the current disc When no folder is selected the first folder will play in random order 4 Press Shuffle Play starts continued sosiq Bui eId 10 suoljouny snoueA g 47 485 To return to normal play Press CLEAR or select OFF in step 3 To turn off the Control Menu display Press DISPLAY repeatedly until the Control Menu display is turned off Note You cannot use this function with a VIDEO CD and Super VCD with PBC playback When you press CLEAR to return to normal play Program Play and Repeat Play are also canceled Playing Repeatedly Repeat Play You can play the contents on a disc repeatedly You can use a combination of Shuffle Play or Program Play modes 1 Press C DISPLAY during playback The Control Menu display appears on the TV screen 2 Press 4 4 to select REPEAT then press The options for REPEAT appear 3 Press V to select the item to be repeated E DVD VIDEO DVD VR OFF Off DISC You can repeat all ofthe titles on the disc TITLE You can repeat the current title on a disc CHAPTER You can repeat the current chapter E VIDEO CD CD OFF Off DISC You can repeats all of the tracks on the disc TRACK You can repeat the current track E DATA CD DATA DVD OFF Off DISC You can repe
112. o select the preset station you want to create an index name for 3 Press SYSTEM MENU 4 Press t repeatedly until NAME IN appears in the front panel display TUNED STEREO D Press or 6 Create a name by using gt Press 4 to select a character then press gt to move the cursor to the next position You can input letters numbers and other symbols for a radio station If you make a mistake Press 2 repeatedly until the character to be changed flashes then press 4 to select the desired character To erase the character press 2 repeatedly until the character to be erased flashes then press CLEAR T Press COMPLETE appears in the front panel display and the station name is stored 8 Press SYSTEM MENU The system menu turns off Viewing the station name or frequency in the front panel display When the system is set to FM or AM you can check the frequency using the front panel display Press DISPLAY Each time you press DISPLAY the front panel display changes as shown Station name 2 Frequency This is displayed if you have entered a name for a preset station Returns to the original display when several seconds have elapsed suomounq 1eun a 6955 706 Using the Radio Data System RDS What is the Radio Data System The Radio Data System RDS is a broadcasting service that allows radio stations to send
113. on the TV Screen The subwoofer and the front speakers in this system are magnetically shielded to prevent magnetic leakage However some leakage may occur as a high strength magnet is employed If this happens check the following items If the speakers are used with a CRT based TV or projector install the speakers at least 0 3 m from the TV set Ifthe colour irregularity persists turn off the TV set once then turn it on after 15 to 30 minutes If howling occurs reposition the speakers further away from the TV set Make sure that no magnetic object magnetic latch on a TV stand health care device toy etc is placed near the speakers continued uoneunoju euonippv 10355 1045 Sound Symptom Remedy There is no sound The speaker cord is not connected securely Press MUTING on the remote if MUTING is displayed on the front panel display The system is in pause mode or in Slow motion Play mode Press L to return to normal play mode Fast forward or fast reverse is performed Press D gt to return to normal play mode Check the speaker settings page 96 The component connected to the HDMI OUT jack does not conform to the audio signal format in this case set AUDIO HDMI in HDMI SETUP to ON page 94 No sound is output from the HDMI OUT jack Set AUDIO HDMI in HDMI SETUP to ON page 94 The HDMI OUT jack is connected to a DVI Digital Visual In
114. one and there should be no obstruction between the speakers and the calibration microphone Note The ECM AC2 jack is used for the supplied calibration microphone only Do not connect other microphones Rear of the control unit 9020 linm N To ECM AC2 jack Calibration microphone C 8 Press 2 to select YES 9 Press 3 AUTO CALIBRATION starts Be quiet during the measurement Avoid being in the measurement area and making noise during the measurement about minute to avoid measurement failure During the measurement test signals are output from the speakers The environment of the room in which the system is installed may affect measurements f an error message appears on the TV screen follow the message then select YES An error message appears when the headphones are connected to the surround amplifier the calibration microphone is not connected front speakers are not correctly connected surround speakers are not correctly connected front and surround speakers are not correctly connected subwoofer is not connected 1 0 Press gt to select YES or NO then press gt ll The measurement is OK Disconnect the calibration microphone then select YES The result is implemented E The measurement is not OK Follow the
115. ont panel 6 1 Soft touch buttons B l FUNCTION 4 MO on standby 34 99 VOLUME 38 5 Disc slot 39 2 Remote sensor 11 6 4 eject 40 3 Front panel display 117 continued uoneuuojuj jeuonippv li 115 116 Control unit rear panel e v E o 5 1 2 3 4 6 7 8 z OOO eD 11 10 9 TV AUDIO IN R L jacks 27 6 VIDEO OUT VIDEO jack 27 ECM AC2 jack 88 7 VIDEO OUT COMPONENT jacks 27 SAT CABLE DIGITAL IN COAXIAL 8 Ventilation slots jack 28 9 DMPORT jack 28 HDMI OUT jack 27 0 AM terminals 30 TV DIGITAL IN OPTICAL jack 27 ff FM 759 COAXIAL jack 30 Front Panel Display About the indications in the front panel display P E amp Nw Ej el LDTS DODIGITAL Flashes when the sleep timer is set 83 Lights up when muting function is activated Lights up when a CD or a DATA CD is loaded Lights up when a station is received Radio only 67 Lights up when the time information of a title or chapter appears in the front panel display DVD only 52 Stereo Monaural effect Radio only 68 Lights up when the S
116. options for the selected item appear Example TV TYPE VIDEO SETUP TV TYPE PROGRESSIVE CcOMPC 4 3 OUTPUT 4 3 LETTER BOX PAUSE MODE 4 3 PAN SCAN Options Press to select a setting then press 5 The setting is selected and setup is complete Example 4 3 LETTER BOX VIDEO SETUP TV TYPE 43 LETTER BOX PROGRESSIVE COMPONENT OUT O 4 3 OUTPUT PAUSE MODE Selected setting Setting the Display or Sound Track Language LANGUAGE SETUP Set various languages for the on screen display or sound track LANGUAGE SETUP OSD MENU AUDIO SUBTITLE AUDIO FOLLOW E OSD On Screen Display You can switch the display language on the TV screen E MENU DVD VIDEO only You can switch the language for the disc s menu E AUDIO DVD VIDEO only You can switch the language of the sound track When you select ORIGINAL the language given priority in the disc is selected E SUBTITLE DVD VIDEO only You can switch the language of the subtitle recorded on the DVD VIDEO When you select AUDIO FOLLOW the language for the subtitles changes according to the language you selected for the sound track Note When you select a language in MENU AUDIO or SUBTITLE that is not recorded on the DVD VIDEO one of the recorded languages will be automatically selected depending on the disc the language may not be selected automatically If you select OTHERS
117. ound formats are downmixed to 2 channels STEREO 4 Press The selected decoding mode is applied 5 Press SYSTEM MENU The system menu turns off To turn the surround effect off Select A F D STD or 2CH STEREO for DEC MODE and set the sound mode page 65 to MOVIE or MUSIC Depending on the disc or source when you select A F D MULTI the beginning of the sound may be cut off as the optimum mode is automatically selected To avoid cutting the sound select A F D STD When the input signal is multi channel source PLII MOVIE and PLII MUSIC are canceled and the multi channel source is output directly When the bilingual broadcast sound is input PLI MOVIE and PLII MUSIC are not effective Depending on the input stream the decoding mode may not be effective When you select A F D MULTI the surround or stereo effect may not be effective In this case select A F D STD PLI MOVIE or PLI MUSIC When changing the decoding mode while using the S AIR receiver not supplied page 76 sound from the S AIR receiver may skip The system memorizes the last decoding mode selected for each function mode Whenever you select a function such as DVD or TUNER the decoding mode that was last applied to function is automatically applied again For example if you listen to DVD with Dolby Pro Logic II MOVIE as the decoding mode then change to another func
118. peaker and subwoofer setting is fixed you cannot change them FRONT YES CENTER YES Normally select this NONE Select this if no center speaker is used SURROUND YES Normally select this NONE Select this if no surround speaker is used SUBWOOFER YES E DISTANCE FRONT When you move the front speakers and center speaker be sure to set the parameters of the distance from the listening position to the speakers You can set the parameters from 0 0 to 7 0 meters for the center speaker L R Set the front speaker distance 3 0 m CENTER Set the center speaker 3 0 m distance SUBWOOFER Set the subwoofer distance 3 0 m 1 When you perform the Quick Setup page 34 the default settings are changed 2 This item appears when you set CENTER to YES in the CONNECTION setting E DISTANCE SURROUND When you move the surround speakers be sure to set the parameters of the distance from the listening position to the speakers You can set the parameters from 0 0 to 7 0 meters L R Set the surround speaker 3 0 m3 distance 3 When you perform the Quick Setup page 34 the default settings are changed 4 This item appears when you set SURROUND to YES in the CONNECTION setting wa Depending on
119. peries that may block the ventilation slots Do not install the control unit near heat sources such as radiators or air ducts or in a place subject to direct sunlight excessive dust mechanical vibration or shock Do not install the control unit in an inclined position It is designed to be operated in a horizontal position only Keep the control unit and discs away from component with strong magnets such as microwave ovens or large loudspeakers Do not place anything on the control unit and the subwoofer f you use more than one set of S AIR products position them away from each other to avoid cross talk nstall this surround amplifier and S AIR products at least 50 cm away from people f you use more than one surround amplifier do not place one on top of the other On operation fthe system is brought directly from a cold to a warm location or is placed in a very damp room moisture may condense on the lenses inside the control unit Should this occur the system may not operate properly In this case remove the disc and leave the system turned on for about half an hour until the moisture evaporates When you move the system take out any disc If you don t the disc may be damaged If anything falls into the cabinet unplug the subwoofer and have it checked by qualified personnel before operating it any further On adjusting volume Do not turn up the volume while listening to a section
120. play the remaining time changes in the front panel display as follows SLEEP OFF SLEEP 90M SLEEP 80M l SLEEP 10M SLEEP 60M SLEEP 70M When you set the sleep timer SLEEP lights up in the front panel display To check the remaining time Press SLEEP once To change the remaining time Press SLEEP repeatedly to select the desired time To cancel the sleep timer function Press SLEEP repeatedly until SLEEP OFF appears in the front panel display suoneijedo 19440 E 83 GB Changing the Brightness Changing the Display of the Front Panel Display Mode The brightness of the front panel display can be INFORMATION MODE set to either of 2 levels You can change the displayed information in the front panel display DIMMER V 9 amp cro e O00 Press DIMMER Each time you press DIMMER the brightness of the front panel display changes tT Press SYSTEM MENU DIMMER OFF Bright 2 Press iv repeatedly until INFO DIMMER ON The front panel display MODE appears in the front panel becomes dark display then press or 2 3 Press to select a setting STANDARD displays information fully such as the kind of disc track number repeat mode information radio frequency etc for the selected function For details of the displayed information see Front Panel Display page 117 SIMPLE displays the selec
121. ppears TRACK LIST 1 03 In the Middle of Nowher 01 Geronimo s Cadillac 02 Riding On A White Swan 03 Give Me Peace On Earth 04 Sweet Little Shella 05 Ten Thousand Lonely Drums 06 Lonely Tears In Chinatown 07 In Shaire Y Press to select a file and press The system starts playing the selected file You can turn the file list off by pressing DVD MENU Pressing DVD MENU again will display the folder list To stop playback Press Bl To play the next or previous MP3 file Press PI to play the next MP3 file Press Ke twice to play the previous MP3 file When you press F once you can go to the beginning of the current MP3 file Note that you can select the next folder by continuing to press P after the last file on the current folder but you cannot return to the previous folder by pressing Ke To return to the previous folder select the folder from the folder list To return to the previous display Press gt RETURN To turn off the display Press DVD MENU Selecting a JPEG image file or folder 1 Load a DATA CD or DATA DVD 2 Press DVD MENU The folder recorded on the DATA CD or DATA DVD appear on the TV screen When a folder is being played its title is shaded FOLDER LIST 01 Let s Talk About Love 1985 02 1st Album 1986 03 In the Middle of Nowhere 1986 04 Ready for Romance 1986 05 In the Garden of Venus 1987 06 Romantic Warriors 1987 07 Back for Goo
122. r down use the wrench supplied 7 Reattach the rear cap using the wrench supplied continued 17 o o 2 LE G S 7 D amp E About connecting speaker cord The connectors of the speaker cords are the same colour as the jacks to be connected There are 2 types of speaker cord for surround speaker You can change the surround speaker cord depending on the type of speaker connection eS e Black Do not catch the speaker cords insulation in the speaker T E terminals o Black You can remove the speaker cords for wired connection from the connector With the catch facing down press and hold the connector down against a flat surface 1 and remove the speaker cords from the connector 2 p 2 V T I I T ATT Catch 7 7 You cannot remove the speaker cords for wireless connection from the connector To avoid short circuiting the speakers Short circuiting of the speakers may damage the system To prevent this be sure to follow these precautions when connecting the speakers Make sure the bare wire of each speaker cord does not touch another speaker terminal or the bare wire of another speaker cord such as shown below Stripped speaker cord is Stripped cords are touching each touching another speaker other due to excessive removal of terminal insulation Note Be sure to match the speaker cords to the appropriate spea
123. remote point it at the remote sensor on the control unit O D e m 4 5 D o Do not leave the remote in an extremely hot or humid place Do not use a new battery with an old one Do not drop any foreign object into the remote casing particularly when replacing the batteries Do not expose the remote sensor to direct sunlight or lighting apparatus Doing so may cause a malfunction If you do not intend to use the remote for an extended period of time remove the batteries to avoid possible damage from battery leakage and corrosion 11 vo o 2 E 2 D 5 E a Step 1 Positioning the Speakers For the best possible surround sound all the speakers other than the subwoofer should be placed at the same distance from the listening position It is recommended that the subwoofer should be placed 2 Place speakers and subwoofer as illustrated below Control unit Front speaker L Front speaker R B Center speaker amp Surround speaker L 5 Surround speaker R amp Subwoofer amp Surround amplifier 1268 You can also place the subwoofer either side facing the listening position When you install the speaker the speaker face may be unstable In this case use a commercially available wire clamper or a commercially available tape etc to secure the speaker cord Usi
124. rms to UDF Universal Disk Format The MP3 file does not have the extension MP3 The data is not formatted in MP3 even though it has the extension MP3 The data is not MPEG 1 Audio Layer 3 data The system cannot play audio tracks in MP3PRO format The MODE MUSIC IMAGE setting has been set to IMAGE page 59 If you cannot change the MODE MUSIC IMAGE setting re load the disc or turn the system off then on The DATA CD DATA DVD contains a DivX video file The JPEG image file cannot be played The DATA CD is not recorded in a JPEG format that conforms to ISO 9660 Level 1 Level 2 or Joliet The DATA DVD is not recorded in a JPEG format that conforms to UDF Universal Disk Format It has an extension other than JPEG or JPG It is larger than 3 072 width x 2 048 height in normal mode or more than 2 000 000 pixels in Progressive JPEG image file which is mainly used on the Internet website It does not fit the TV screen those images are reduced The MODE MUSIC IMAGE setting has been set to MUSIC page 59 If you cannot change the MODE MUSIC IMAGE setting re load the disc or turn the system off then on The DATA CD DATA DVD contains a DivX video file The MP3 files and JPEG image files start playing simultaneously AUTO has been selected in MODE MUSIC IMAGE page 59 The DivX video file cannot be played The file is not created in DivX format
125. s or registered trademarks of HDMI Licensing LLC BRAVIA is a trademark of Sony Corporation S AIR and its logo are trademarks of Sony Corporation gas vo o 2 LE 77 5 E 3 Getting Started Unpacking Control unit 1 Speakers Front left speaker white connector for wired connection only Front right speaker red connector for wired connection only Center speaker green connector for wired connection only Surround left speaker blue connector for wireless connection only 10 Surround right speaker gray connector for wireless connection only FM wire antenna aerial 1 rorem Video Cord 1 Remote Commander remote 1 R6 size AA batteries 2 lt Surround amplifier TA SA100WR 1 Speaker cord cover 1 p Speaker cord holder 1 lt Wireless adapters Wireless transceiver EZW RTIO 1 NS Wireless transmitter EZW T100 1 Speaker cords 2 for surround speakers wired connection only Brackets 5 Wrench 1 Operating Instructions Quick Start Guide card 1 Inserting batteries into the remote You can control the system using the supplied remote Insert two R6 size AA batteries by matching the and ends on the batteries to the markings inside the compartment To use the
126. s which sharing the 2 4 GHz band such as wireless LAN or Bluetooth the transmission of S AIR products or other wireless systems may be unstable In this case the transmission may be improved by changing the following RF CHANGE setting 1 Press SYSTEM MENU 2 Press t repeatedly until RF CHANGE appears in the front panel display then press or gt 3 Press 4 4 to select the desired setting AUTO Normally select this The system change RF CHANGE to ON or OFF automatically ON The system transmits sound by searching the better channel for transmitting OFF The system transmits sound by fixing the channel for transmitting 4 Press G The setting is made D Press SYSTEM MENU The system menu turns off 6 When you set RF CHANGE to OFF select the ID so that sound transmission is most stabilized page 75 When the wireless transmitter is not inserted in the S AIR main unit you cannot set RF CHANGE n most cases you will not need to change this setting If RF CHANGE is set to OFF transmission between the S AIR main unit and S AIR sub unit can be performed using one of the following channels S AIR ID A equivalent channel for Wi Fi channel 1 S AIR ID B equivalent channel for Wi Fi channel 6 S AIR ID C equivalent channel for Wi Fi channel 11 The transmission may be improved by changing the transmission chann
127. ssed digitally less signal degradation occurs Dolby Pro Logic II Dolby Pro Logic II creates 5 full bandwidth output channels from 2 channel sources This is done using an advanced high purity matrix surround decoder that extracts the spatial properties of the original recording without adding any new sounds or tonal colourations E Movie mode The Movie mode is for use with stereo television shows and all programs encoded in Dolby Surround The result is enhanced sound field directionality that approaches the quality of discrete 5 1 channel sound E Music mode The Music mode is for use with any stereo music recordings and provides a wide and deep sound space DTS Digital audio compression technology developed by DTS Inc This technology conforms to 5 1 channel surround This format comprises of stereo rear channel and there is discrete subwoofer channel in this format DTS provides the same 5 1 discrete channels of high quality digital audio The good channel separation is realized due to the all channel data being recorded discretely and processed in digitally HDMI High definition multimedia interface HDMI is an interface that supports both video and audio on a single digital connection allowing you to enjoy high quality digital picture and sound The HDMI specification supports HDCP high bandwidth digital contents protection a copy protection technology that incorporates coding technology for digital video sig
128. sult Be sure to fully extend the FM wire antenna aerial After connecting the FM wire antenna aerial keep it as horizontal as possible Adjust the direction of the AM loop antenna aerial for best AM broadcast sound f you have poor FM reception use a 75 ohm coaxial cable not supplied to connect the control unit to an outdoor FM antenna aerial as shown below Outdoor FM Control unit antenna aerial 3055 Connecting the AC power cord mains lead Before connecting the AC power cords mains lead of the subwoofer and the surround amplifier to a wall outlet mains connect the front center speakers to the subwoofer and surround speakers to the surround amplifier page 23 Rear of the subwoofer s S AIR ID B Te OM sme To a wall outlet mains zi AC power cord mains lead To a wall outlet mains AC power cord mains lead After connecting the AC power cord mains lead wait about 20 seconds before turning on the power by pressing Vc 31 peyeys Dunes o o 2 E 7 D 5 E 3 Step 3 Setting up the Wireless System To use the wireless system you need to set up the surround amplifier Before setting make sure that the wireless transmitter and transceiver are inserted into the subwoofer and the surround amplifier correctly page 25 This wireless system is called S AIR
129. t signal of the system to progressive format page 37 HDMI High Definition Multimedia Interface If your TV has the HDMI jack use this connection and select the type of output signal page 36 Note During the DMPORT function video signal is not output from the HDMI OUT and COMPONENT VIDEO OUT jacks The system can accept both digital and analog signals Digital signals have priority over analog signals If the digital signal ceases the analog signal will be processed after 2 seconds When connecting the HDMI cable make sure that the direction of jacks are the same When connecting the digital optical cord insert the connector until it clicks into place Tip You can connect another component such as a VCR digital satellite receiver or PlayStation to the TV AUDIO IN jacks or TV DIGITAL IN OPTICAL jack instead of the TV 2768 o o E LI S 7 D amp E Connecting the other components You can enjoy the connected component using the speakers of the system Rear of the control unit Digital coaxial cord not supplied er es G bh To the digital coaxial output jack of another component e g digital satellite receiver DIGITAL MEDIA PORT adapter To connect the DIGITAL MEDIA PORT adapter Connect the DIGITAL MEDIA PORT adapter to the DMPORT jack For details see Using the
130. t your nearest Sony dealer There is no sound turns green Check the status of the The speaker cord is not connected securely POWER ON LINE indicator Check the speaker connections and settings on the surround amplifier The volume of the system is set to minimum The S AIR main unit is in mute status Depending on the source or the settings of the unit the effect of the speakers may be less noticeable Headphones are connected flashes green The S AIR main unit is not turned on You performed pairing the S AIR main unit and another S AIR sub unit The surround amplifier is paired to another S AIR main unit Confirm the IDs of the S AIR main unit and surround amplifier page 75 Pairing operation is not completed Sound transmission is poor Move the surround amplifier so that the POWER ON LINE indicator turns green Install the subwoofer and surround amplifier apart from another wireless product uoneunoju euonippv Stop using another wireless product The wireless transceiver s is are not inserted correctly turns red Change the SURROUND SELECTOR switch SURROUND or SURROUND BACK of the surround amplifier to match the S AIR main unit HP NO LINK and VOLUME Volume becomes the minimum when you turn off the surround amplifier with MIN appear alternately in the headphones connected before you turn off the system or if radio receptio
131. tain conditions Witha DATA CD DATA DVD that contains DivX video files in addition to MP3 audio tracks or JPEG image files the system plays only the DivX video files However this system only plays a DATA CD of format ISO 9660 Level 1 Level 2 or Joliet and a DATA DVD of Universal Disk Format UDF Refer to the operating instructions supplied with the disc drives and the recording software not supplied for details on the recording format About playback order of data on a DATA CD or DATA DVD Note that the playback order may not be applicable depending on the software used for creating the DivX video file or if there are more than 200 folders and 150 DivX video files in each folder wa The system may not be able to play some DATA CDs DATA DVDs created in the Packet Write format DivX video files that the system can play The system can play data that is recorded in DivX format and which has the extension AVI or DIVX The system will not play files with the extension AVI or DIVX if they do not contain a DivX video For details about playable MP3 audio tracks or JPEG image files on a DATA CD or DATA DVD see Playable Discs page 6 Note The system may not play a DivX video file when the file has been combined from two or more DivX video files The system cannot play a DivX video file of size more than 720 width x 576 height or 2GB Depending on the DivX vi
132. ted function name only 4 Press The setting is made D Press SYSTEM MENU The system menu turns off 845 Changing the Display Appearance of the Soft touch Buttons ILLUMINATION MODE You can select the way of displaying the soft touch buttons located on the top of the control unit T V 2 SYSTEM MENU 1 Press svsrEM MENU 2 Press t repeatedly until ILLUM MODE appears in the front panel display then press or gt 3 Press t to select a setting STANDARD sets the soft touch buttons lit up always SIMPLE sets the soft touch buttons lit up when you touch them To operate the soft touch buttons touch them once and light them up The soft touch buttons turn off if you do not touch them for about 10 seconds 4 Press The setting is made 5 Press SYSTEM MENU The system menu turns off Note When the soft touch buttons turn off in SIMPLE mode first touch the soft touch button area so that the soft touch buttons light up then operate the system with them Soft touch button area Even if SIMPLE mode is set only B on the top of the control unit lights up during playback suoneiedo 19440 E 0565 8665 Advanced Settings and Adjustments Restricting Playback of the Disc PARENTAL CONTROL Dvp v Playback of some DVD VIDEOs can be limited according to a predetermined level such as the age of the users Scenes may be b
133. terface device DVI Digital Visual Interface jacks do not accept audio signals Try the following O Turn the system off and on again Turn the connected component off and on again 8 Disconnect and then connect the HDMI cable again The left and right sounds are unbalanced or reversed Check that the speakers and components are connected correctly and securely Perform AUTO CALIBRATION page 88 Severe hum or noise is heard Check that the speakers and components are connected securely Check that the connecting cords are away from a transformer or motor and at least 3 meters away from your TV set or a fluorescent light Move your TV away from the audio components The plugs and jacks are dirty Wipe them with a cloth slightly moistened with alcohol Clean the disc The sound loses stereo effect when you Set AUDIO to STEREO by pressing AUDIO page 50 play a VIDEO CD a CD or an MP3 file Make sure the control unit is connected properly The surround effect is difficult to hear Check the DEC MODE setting page 63 when you are playing a Dolby Digital Check the speaker connections and settings pages 23 96 DTS or MPEG audio Depending on the DVD the output signal may not be the entire 5 1 channel It may be monaural or stereo even if the sound track is recorded in Dolby Digital or MPEG audio format The sound comes from the center speaker only C
134. terior of the control unit On moving the system When you carry the system use the following procedure to protect the inner mechanism 1 Press amp to remove a disc Make sure that the disc is removed from the control unit 2 Press I to turn off the power 3 Remove the AC power cord mains lead from the wall outlet mains About S AIR function As the S AIR function transmits sound by radio waves sound may skip when radio waves are obstructed This is a characteristic of radio waves and is not malfunction As the S AIR function transmits sound by radio waves equipment that generates electromagnetic energy such as a microwave oven may interfere with sound transmission As the S AIR function uses the radio waves that share the same frequency as other wireless systems such as wireless LAN or Bluetooth interference or poor transmission may result In this case take the following steps Do not install the system near other wireless systems Do not use the system and the other wireless systems at the same time The transmission distance differs depending on the usage environment Find a location where transmission between the S AIR main unit and S AIR sub unit is most effective and install the S AIR main unit and S AIR sub unit there About the surround amplifier The nameplate is located on the side exterior Notes about the Discs On handling discs To keep the disc clean handle the
135. the DIGITAL MEDIA PORT adapter to from the control unit while the system is turned on Depending on the type of DIGITAL MEDIA PORT adapter images may also be output In this case the system outputs only a composite video signal see page 26 connection method regardless of the type of video signal When you use the system and the Bluetooth Wireless Audio Adapter such as TDM BT1 not supplied at the same time transmission distance between the Bluetooth transmitter and Bluetooth Wireless Audio Adapter may be reduced In this case place the Bluetooth transmitter as far as possible from the system or move the Bluetooth Wireless Audio Adapter closer to the Bluetooth transmitter When you use the system and the Wireless Network Audio Adapter such as TDM NCI not supplied at the same time place the Wireless Network Audio Adapter as far as possible from the system 914 q orpny EUJ9 X3 IIAGH 40 01 U0D a 73 GB 746 Playing the connected component on the system 1 Press FUNCTION repeatedly until DMPORT appears in the front panel display 2 Start playback of the connected component The sound and images from the connected component are played on the system or connected TV For operation details refer to the operating instructions of the DIGITAL MEDIA PORT adapter When listening to MP3 or other compressed music using a portable audio source you can enhance the sound Select A F D STD for
136. tion and then return to DVD Dolby Pro Logic II MOVIE will be applied again Selecting the Sound Mode cm GE IZ a a ITT You can choose a suitable sound mode for movies or music SOUND MODE Press SOUND MODE repeatedly during playback until the desired mode appears in the front panel display AUTO The system selects MOVIE or MUSIC automatically to produce the sound effect depending on the disc or sound stream MOVIE The system provides sound suitable for movies MUSIC The system provides sound suitable for music SPORTS The system adds reverberation for the sports program NEWS The system provides the sound for the voice program such as news e OMNI DIR The system reproduces the stereo effect everywhere surrounding by satellite speakers Note Depending on the disc or source when you select AUTO the beginning of the sound may be cut off as the system selects the optimum mode automatically To avoid cutting the sound select other than AUTO When changing the sound mode while using the S AIR receiver not supplied page 76 sound from the S AIR receiver may skip The system memorizes the last sound mode selected for each function mode When you select SPORTS depending on the input stream Pro Logic II music may be applied automatically When you connect headphones to the surround amplifier you can select AUTO MOVIE or MUSIC
137. tions of the TV Enjoying Multiplex Broadcast Sound DUAL MONO You can enjoy multiplex broadcast sound when the system receives or plays the Dolby Digital multiplex broadcast signal To receive the Dolby Digital signal you need to connect a TV or other components to the control unit with an optical or coaxial digital cord pages 27 28 and set the digital output mode of the TV or other components to Dolby Digital AUDIO Press AUDIO repeatedly until the desired signal appears in the front panel display MAIN Sound of the main language will be output SUB Sound of the sub language will be output MAIN SUB Mixed sound of both the main and sub languages will be output Enjoying the Sound at Low Volume NIGHT MODE You can enjoy sound effects or dialogue as you would in a movie theatre even at low volume It is useful for watching movies at night I NIGHT Press NIGHT NIGHT lights up in the front panel display and the sound effect is activated To enjoy more effects set AUDIO DRC to STANDARD or MAX page 95 To turn off the sound effect Press NIGHT again Using the Sleep Timer You can set the system to turn off at a preset time so you can fall asleep listening to music You can preset the time in 10 minutes decrements SLEEP Press SLEEP Each time you press SLEEP the minute dis
138. to the Control Menu display by selecting NO here 8 Press Do not press l D while resetting the system as it takes a few seconds to complete wa When you turn the system on after resetting and no disc is in the control unit the guide message appears on the TV screen To perform the Quick Setup page 34 press 5 to return to normal screen press CLEAR The MODE MUSIC IMAGE INTERVAL and EFFECT settings are also return to the default settings sjueunsn py pue sB5uim s pesueapy H 09565 100 Additional Information Precautions On power sources Unplug the subwoofer from the wall outlet mains if you do not intend to use it for an extended period of time To disconnect the cord pull it out by the plug never by the cord On placement Place the system in a location with adequate ventilation to prevent heat build up in the system Athigh volume over long periods oftime the cabinet becomes hot to touch This is not a malfunction However touching the cabinet should be avoided Do not place the control unit in a confined space where ventilation is poor as this may cause overheating Do not block the ventilation slots by putting anything on the system The system is equipped with a high power amplifier If the ventilation slots are blocked the control unit can overheat and malfunction Do not place the control unit on surfaces rugs blankets etc or near materials curtains dra
139. u can enjoy the system s sound in a place apart from the control unit by connecting the headphones to the PHONES jack on the surround amplifier wa When you connect headphones to the surround amplifier neither the control unit nor the surround amplifier outputs sound from the system s speakers The volume of the system may become minimize if you turn off the surround amplifier while the headphones are connected to the surround amplifier or radio reception is poor In this case HP NO LINK and VOLUME MIN appear alternately in the front panel display Check radio reception and set the volume again When you use the multiple S AIR product You can prevent miss transmission between the S AIR products by setting a different ID for each S AIR product For details see Establishing sound transmission between the S AIR main unit and S AIR sub unit ID setting page 75 To prevent the transmission by neighbours To prevent the transmission from neighbours you can identify the S AIR main unit and the surround amplifier by performing the pairing operation For details see Identifying the S AIR main unit with a specific S AIR sub unit Pairing operation page 77 To attach the cover to the surround amplifier After connecting and setting you can attach the cover to the surround amplifier for organizing and storing excess speaker cords 1 Attach the speaker cord cover by sliding it down along the groo
140. u select 2 STEREO 2 1 L or 2 2 R Checking the audio signal format DVD VIDEO DATA DVD DATA CD only If you press AUDIO repeatedly during playback the format of the current audio signal PCM Dolby Digital DTS etc appears as shown below E DVD Example Dolby Digital 5 1 channel LFE Low Surround L R Frequency Effect 1 ENGLISH poLey niar Front L R Center Currently playing program format Example Dolby Digital 3 channel Surround Front L R Monaural 1 SPANISH DpOLBYDIGITAL Currently playing program format W DATA CD DivX video file DATA DVD DivX video file Example MP3 audio 1 MP3 28k Bit rate Selecting ORIGINAL or PLAY LIST on a DVD VR This function is only available for DVD VRs with a playlist created 1 Press DISPLAY while the system is in stop mode The Control Menu display appears on the TV screen Press 4 4 to select KE ORIGINAL PLAY LIST then press The options for ORIGINAL PLAY LIST appear Press t to select a setting PLAY LIST You can play the titles created from ORIGINAL for editing ORIGINAL You can play the titles originally recorded Press sosiq BuiAe d 10 suonoung snoueA g 51 GB 5268 Viewing Information About the Disc Viewing the playing time and remaining time in the front panel display Pr
141. ur TV or to use some of the buttons above The TV mode turns off when you do not operate the remote for 10 seconds suoneijedo 19440 E By pressing You can TV Turn the TV on or off THEATRE Enjoy optimal image suited for movies TV VOL Adjust the TV volume TV CH Select the TV channel Numeric buttons Select the TV channel e ENTER TOOLS Displays the operation menu for the current display RETURN Return to the previous channel or layer on the menu of the TV MENU Display the menu of the TV MUTING Turn off the TV sound temporarily t V 3 Select the item on the menu PROG 4 Select the TV channel ae After pressing GJ you can select the next E or previous EV text page Number buttons Select the TV channel Eu After pressing GJ you can select the text page by entering the three digit page number ANALOG Switch to analogue mode continued 61 GB 8268 By pressing You can DIGITAL Switch to digital mode Display the information Access Text Coloured buttons Select the options on the menu Display the Digital Electronic Programme Guide EPG Switch the TV s input source between the TV and other input sources in TV mode After pressing you can hold the current text page The function of these buttons are same as the remote buttons of the Sony TV For details refer to the operating instruc
142. us Functions for Playing Discs Searching for a Title Chapter Track Scene etc You can search a DVD VIDEO DVD VR by title or chapter and you can search a VIDEO CD CD DATA CD DATA DVD by track index or scene Fora DATA CD DATA DVD you can search by folder or file As titles and tracks are assigned unique numbers on the disc you can select the desired title or track by entering its number Or you can search for a scene using the time code 1 Press DISPLAY When playing a DATA CD DATA DVD with JPEG image files press DISPLAY twice The Control Menu display appears on the TV screen 2 Press to select the search method Example when you select P CHAPTER is selected refers to a number The number in parentheses indicates the total number of titles chapters tracks indexes scenes folders or files 98 99 13 99 DVD VIDEO BOSE REA Selected row 3 Press changes to 99 99 DVD VIDEO OF 4 Press t V or the numeric buttons to select the desired title chapter track index scene etc If you make a mistake Cancel the number by pressing CLEAR then select another number D Press Q The system starts playback from the selected number When the Control Menu display is turned off you can search for a chapter DVD VIDEO DVD R DVD RW track VIDEO CD CD or file DATA CD DATA DVD DivX video fil
143. vX video files You may not be able to use the instant replay or instant advance function with some scenes 40 Enjoying the Radio or Other Components Selecting the connected component You can use a TV VCR or other components connected to the TV or SAT CABLE jacks on the rear of the control unit Refer to the operating instructions supplied with the components for further information o o 7 me E 7 Press FUNCTION repeatedly until the desired function name appears in the front panel display Each time you press FUNCTION the mode of the system changes in the following sequence DVD FM AM TV SAT CABLE DMPORT DVD You can assign a digital sound input corresponding with the function TV and SAT CABLE For details see DIGITAL IN page 95 Note When you use both the TV AUDIO IN jacks analog connection and TV DIGITAL IN OPTICAL jack digital connection at the same time the digital connection takes priority 416 Changing the input level of the sound from connected components Distortion may occur when you listen to a component connected to the TV AUDIO IN jacks on the rear of the control unit This is not a malfunction and will depend on the component connected To prevent distortion reduce the input level on the control unit FUNCTION em S L 9 2 m O GO GG OG
144. ves along the edges of the surround amplifier Speaker cord cover Surround amplifier Push the speaker cord cover down until you hear a click Turn the surround amplifier upside down then store the cords in the speaker cord cover 2 Insert the tabs of the speaker cord holder in the slots of the speaker cord cover and press it into place Speaker cord holder Surround amplifier Note When detaching remove the speaker cord holder then remove the speaker cord cover To remove the speaker cord holder slightly press the catch of the holder and lift off To remove the speaker cord cover slightly splay open the edges of the cover and slide down Do not use excessive force to store the cords 3365 G o El e o D D vo o 2 LE 7 5 E 3 Step 4 Performing the Quick Setup Follow the steps below to make the basic adjustments for using the system Note When you connect the system and the TV with the component video cord not supplied or HDMI cable not supplied you need to set the type of video output for matching your TV For details see Setting the type of video output to match your TV page 36 yo eltt C3 DISPLAY 1 Turn on the TV 2 Press IC on the control unit and POWER on the surround amplifier The system turns on Make sure that the function is set to DVD page 41 3 Switch the input s
145. w You cannot rotate the JPEG image file when you set JPEG RESOLUTION in HDMI SETUP to 1920x1080i HD J or 1920 x10801 HD page 94 To stop playback Press Bl Displaying the list of MP3 files JPEG image files DivX video files 1 Press DISPLAY during playback The Control Menu display appears on the TV screen 2 Press V to select LE BROWSING then press The options for BROWSING appear 3 Press V to select the desired list then press FOLDER LIST The list of folders appears Follow step 3 of Selecting an MP3 file or folder page 56 or Selecting a JPEG image file or folder page 57 PICTURELIST Images of JPEG image files in the folder appear in 16 subscreens Follow step 3 of Selecting a JPEG image file or folder page 57 If there is no JPEG image file in the selected folder No image data appears In this case select FOLDER LIST to display the list of folders Playing MP3 Files and JPEG Image Files as a Slide Show with Sound You can play a slide show with sound by first placing both MP3 files and JPEG image files in the same folder ona DATA CD or DATA DVD 1 Load a DATA CD or DATA DVD 2 Press DISPLAY while the system is in stop mode The Control Menu display appears on the TV screen 3 Press V to select MODE MUSIC IMAGE then press The options for MODE MUSIC IMAGE appear 4 Press to select a setting
146. ware that among those discs there are some that do not conform to the CD standard and may not be playable by this product Note on DualDiscs A DualDisc is a two sided disc product which mates DVD recorded material on one side with digital audio material on the other side However since the audio material side does not conform to the Compact Disc CD standard playback on this product is not guaranteed About Multi Session CD This system can play a Multi Session CD when an MP3 file is contained in the first session Any subsequent MP3 files recorded in later sessions can also be played back This system can play a Multi Session CD when a JPEG image file is contained in the first session Any subsequent JPEG image files recorded in later sessions can also be played back If MP3 files and JPEG image files in music CD format or video CD format are recorded in the first session only the first session will be played back Region code Your system has a region code printed on the bottom of the control unit and will only play a DVD labeled with the same region code A DVD VIDEO labeled will also play on this system If you try to play any other DVD VIDEO the message Playback prohibited by area limitations will appear on the TV screen Depending on the DVD VIDEO no region code indication may be given even though playing the DVD VIDEO is prohibited by area restrictions Note about playback operations of a DVD and VIDEO CD

Download Pdf Manuals

Related Search

Related Contents

Manual de Usuario TDT HD 3  Guía del usuario de la serie todo en uno X5150  PCI8282 User`s Manual  Desa VN30T Electric Heater User Manual  Steyr LG 110 Operator  Lignes directrices sur la prévention des blessures  Samsung PS-42C7H Manual de Usuario  Amiga Tandem - Pro  Manual Disponível  TEMPORIZADOR DE ÁGUA ELECTRÓNICO  

Copyright © All rights reserved. Failed to retrieve file