Socket Mobile 10/100 Network Card User Manual
Contents
1. Warning Label not shown ssl Binaba DC650TS HP Hardware Package not shown 0 indicates included in Hardware Package indicates quantity included in Hardware Package 12 Wiring Diagram Capacitor Capacitor White Black Green Ground Capacitor 2 90 Capacitor White Black Green 132. Order the Dust Collection Basics Video which covers topics such as system design duct Assembly A WARNING The dust collector must be disconnected from the power source during assembly Failure to comply may result in serious injury The JET DC 650TS does not come with a collector can You can use the JET two stage dust collector on a variety of round metal and plastic collector cans The outer diameter of the trash can should be approximately 20 1 4 24 1 4 to fit properly 1 Attach the deflector A Fig 1 to the plastic cover using two hex cap screws four flat washers and two hex nuts B Fig 1 Tighten the hardware 2 Attach the impeller guard C Fig 1 to the plastic cover with three flat washers and three hex nuts D Fig 1 Tighten the hardware A WARNING To reduce the risk of injury from moving parts always keep impeller guard in place Failure to comply may result in serious injury 3 Slide the elbow A Fig 2 over the impeller housing exhaust and tighten in place with one hex cap screw one flat washer and one hex nut B Fig 2 4 Connect the filter A Fig 3 to the elbow and turn counter clockwise so that it locks in place A WARNING Static electricity will build up in the filter during operation The filter ground must be attached to the machine ground and to the filter Failure to comply may result in fire loss of property or personal injury 5 At
3. normal motor ventilation Fig 4 Cleaning the Filter A CAUTION Wearing a particle mask respirator for protection against fine dust particles during cleaning is highly recommended Clean both the filter and collector can frequently to keep the collector s performance at its optimum To clean 1 Disconnect the machine from the power source 2 Take off the grounding clip and remove the filter A Fig 5 by turning clockwise 3 Empty the contents into an appropriate container 4 The filter can be cleaned with a low pressure air hose Blow from the outside of the filter to clean the dust particles For best results check and empty the filter frequently Some applications will fill up the filter quicker than others A WARNING Static electricity will build up in the filter during operation The filter ground must be attached to the machine ground and to the filter Failure to comply may result in fire loss of property or personal injury 5 Install the filter and reattach the grounding clip Emptying the Collector Can 1 Disconnect the machine from the power source unplug 2 Lift the dust collector off the collector can B Fig 5 3 Dispose of the contents in the collector can Use the proper type hose C Fig 5 to connect the dust collector to the machine being operated Dryer vent hose is not acceptable for this purpose Contact your nearest JET distributor for the full line of JE
4. receptacle as shown in B if a properly grounded outlet is not available The temporary adapter should only be used until a properly grounded outlet can be installed by a qualified electrician This adapter is not applicable in Canada The green colored rigid ear lug or tab extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box as shown in B THREE PRONG PLUG SIS e GROUNDING EAR SECURED GROUNDING PRONG WITH SCREW Q GROUNDED OUTLET 230 Volt Operation If 230V single phase operation is desired the following instructions must be followed 1 Disconnect the machine from the power source 2 This dust collector is supplied with four motor leads that are connected for 115V operation as shown in Figure A Reconnect these four motor leads for 230V operation as shown in Figure B 3 The 115V attachment plug A supplied with the dust collector must be replaced with a UL CSA listed plug suitable for 230V operation D Contact your local Authorized JET Service Center or qualified electrician for proper procedures to install the plug The dust collector must comply with all local and national codes after the 230 volt plug is installed 4 The dust collector with a 230 volt plug should only be connected to an outlet having the same configuration D No adapter is available or should be used with the 230 volt plug Important In all cases 115 or 230 volts make certain the
5. receptacle in question is properly grounded If you are not sure have a registered electrician check the receptacle 230 Volt 1 3 2 4 Black Red Gray Yellow 115 Volt 1 3 2 4 Black Red Gray Yellow Y THREE PRONG PLUG FIGURE A FIGURE B e ki y GROUNDING PRONG 00 O GROUNDED OUTLET Specifications DC 650TS SIA ANN 708630 Blower Wheel Diameter iii 11 Sound Rating at 3 feet iii 60 70 db Ine EBJET C Rm 4 Na 650 Velocity at 4 d ud RR 7 445 Static Pressure inch of water sise 7 80 Overall Dimensions SE 26 3 16 dia x 28 H Motor TEFC PM 1 HP 1Ph 115V 230V Net Weight approx RM 53 lbs Table of Contents Page Warranty tna a M anAD 2 En SERO 3 Grounding Instructions sise 4 115 Volt 0 011 clio PN 4 230 Volt Operation EE 5 Specifications sise 6 Table of Contents RM 6 Unpacking DC 650TS REM 7 Contents of Shipping Carton iii 7 Tools Required for Assembly usine 7 Assemb asana a a a a E S 8 Electrical COnnectiONS ARM 9 Turning the Machine On 8 Off iii 9 Maintenance REM 9 10 Parts Breakdown and Parts List sise 11 12 Wiring Diagram a RA RANA RURA ND LELLANDhLDRLANLLLERLANh LAAL 13 The specifications in this manual are given as general information and are not binding JET Equipment 8 Tools reserves the right to effect at any time and without prior notice changes or alterations to parts fittings and accessory equipment deemed nece
6. silica from bricks and cement and other masonry products and Arsenic and chromium from chemically treated lumber Your risk from those exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as those dust masks that are specifically designed to filter out microscopic particles Do not operate tool while under the influence of drugs alcohol or any medication Make sure the extension cord is in good condition When using an extension cord be sure to use one heavy enough to carry the current your product will draw An undersize cord will cause a drop in the line voltage resulting in loss of power and overheating The table below shows the correct size to use depending on cord length and nameplate ampere rating If in doubt use the next heavier gauge The smaller gauge number the heavier the cord Static electricity will build up in the filter during operation The filter ground must be attached to the machine ground and to the filter Cord Length Cord Gauge 25 16 AWG 50 16 AWG 100 14 AWG 150 12 AWG SAVE THESE INSTRUCTIONS Grounding Instructions Caution This tool must be grounded while in use to protect the operator from electric shock In the event of a malfunction or breakdown grounding provides a path of least resistance for electric current to reduce the risk of electric shock This tool is eq
7. JET EQUIPMENT amp TOOLS OWNER S MANUAL DC 650TS Dust Collector JET EQUIPMENT amp TOOLS INC P O BOX 1349 Phone 253 351 6000 A WMH Company Auburn WA 98071 1349 Fax 1 800 274 6840 www jettools com e mail jet jettools com M 708630 08 01 This manual has been prepared for the owner and operators of the JET DC 650TS Its purpose aside from machine operation is to promote safety through the use of accepted correct operating and maintenance procedures Completely read the safety and maintenance instructions before operating or servicing the machine To obtain maximum life and efficiency from your Dust Collector and to aid in using the machine safely read this manual thoroughly and follow instructions carefully Warranty amp Service The JET Group warrants every product it sells If one of our tools needs service or repair one of our Authorized Repair Stations located throughout the United States can give you quick service In most cases any one of these JET Group Repair Stations can authorize warranty repair assist you in obtaining parts or perform routine maintenance and major repair on your JET Performax or Powermatic tools For the name of an Authorized Repair Station in your area please call 1 800 274 6848 More Information Remember the JET Group is consistently adding new products to the line For complete up to date product information check with your local JET Group distributor JET Group Warranty The
8. JET Group including Performax and Powermatic brands makes every effort to assure that its products meet high quality and durability standards and warrants to the original retail consumer purchaser of our products that each product be free from defects in materials and workmanship as follow 1 YEAR LIMITED WARRANTY ON ALL PRODUCTS UNLESS SPECIFIED OTHERWISE This Warranty does not apply to defects due directly or indirectly to misuse abuse negligence or accidents normal wear and tear repair or alterations outside our facilities or to a lack of maintenance THE JET GROUP LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD SPECIFIED ABOVE FROM THE DATE THE PRODUCT WAS PURCHASED AT RETAIL EXCEPT AS STATED HEREIN ANY IMPLIED WARRANTIES OR MERCHANTIBILITY AND FITNESS ARE EXCLUDED SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG THE IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU THE JET GROUP SHALL IN NO EVENT BE LIABLE FOR DEATH INJURIES TO PERSONS OR PROPERTY OR FOR INCIDENTAL CONTINGENT SPECIAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR PRODUCTS SOME STATES DO NOT ALLOW THE EXLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU To take advantage of this warranty the product or part must be returned for examination postage prepaid to an Authorized Repair Station designated by our office Proof of purchase date and an explanation of the complaint mus
9. T Dust Collector Hoses and Accessories Customize your installation and obtain maximum performance with JET s dust hoods hoses clamps fittings and blast gates Order the Dust Collection Basics Video which covers topics such as system design duct material fittings construction and grounding Stock JW1050V Fig 6 10 Parts Breakdown amp Parts List for the DC 650TS Index Part No No Description Size Qty Tus 331019AW Impeller Housing upper ss 1 2 ens 331019BW Impeller Housing lower sees 1 Bunn MH331001 Motor oct t es 115V 230V 1HP 1Ph 1 venen Sedans DC1100 50W Motor Fan Cover not shown sss Hesse MF411012 Motor Fan not shown tt Hess CA003030 Running Capacitor not shown 30MFD 300V 1 Hesse CA020010 Starting Capacitor not shown 200MFD 125V 1 E DC650TS CS Centrifugal Switch not shown ssl Aoi uos ko oU Kag PAA SWEN ana AA Ae NAA MALA NAA ALA NABA AG 1 JE Q999 10s ete Power Gori ANAN AK ALAALA Ad 1 Dus 423023 tovt Motor Packing rasstedet 1 TERRE 331020 Impeller teet ons rte a TE ns 1 Bode 998621 ctetu strain Help AA AA AA AA NAPALA AA A A A A 1 ie UMUR KS050525 IK AA ka ta nn han BXBX2B
10. ed cord or plug If Dust Collector is not working as it should has been dropped damaged left outdoor or dropped in water return it to a service center Do not pull or carry by cord use cord as a handle close a door on cord or pull cord around sharp edges or corners Do not run Dust Collector over cord Keep cord away from heated surfaces Do not unplug by pulling on cord To unplug grasp the plug not the cord Do not handle plug or Dust Collector with wet hands Do not put any objects into the openings Do not use with any opening blocked keep free of dust lint hair and anything that may reduce air flow Keep hair loose clothing fingers and all parts of body away from opening and moving parts Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes Do not use without dust bag and or filters in place Turn off all controls before unplugging Use extra care when cleaning on stairs Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present Do not operate without hose connected to the hose inlet Hazardous moving parts inside Unplug before removing hose inlet or impeller guard Some dust created by power sanding sawing grinding drilling and other construction activities contains chemicals known to cause cancer birth defects or other reproductive harm Some examples of these chemicals are Lead from lead based paint Crystalline
11. skikken 1 102425 291001 teet COV EM tab et SL 1 Vu EMAS HS430018 Hosen aa AKO AA AA a Aa 1 125555 391004 utt 6 Plastic Impeller Guard nn 1 135225 391016 teeth EFE C EDD PERENNE 1 14 391023 120 ttd GASKET see i had tae Ten ted ik dan dead ist an 1 15 253 423068 jon Ring Clamp de A aalala 1 16 455 391021 toss Deflectorz eA A tun 1 T sudes 391018 tertie AA BN 1 185 391022 5 5 tette Filter de dd 1 194 331027 xi Ai IEEE cM IE 1 20 SG060500 Hex Head Bolt W Flange MOX25 i teo 5 21 2 TS 1482021 Hex Head Bolt L MEXA 2 ees 2 6 Ze iye TS 1482044 Hex Head Bolt L M6X20 sse 1 1 29 554 WFO061310 Flat Washer awa sss MOX19 eus 8 8 24 WF164030 Flat Washer ena MISX4Q rekene 1 25 s g TS 1551041 Spring Washer MO tc tuta E 4 26 154 TS 1540044 Ne MO tus 6 6 211 55 TS 0561072 Nessa 5 8 A8UNE uns 1 285205 TS 1540044 MIU DD MG unt 14 29 dn SG069300 Hex Head Bolt W Flange MOX TZ aa BABA 9 30 WF061620 Flat Washer i ti aaas MOX16 dtd 4 Blu 331099 mm Grounding Clip A A Ai a As dk 1 DC650TS NP Name Plate not shown ST DC650TS WL
12. ssary for any reason whatsoever material fittings construction and grounding A WARNING Stock JW1050V Read and understand the entire contents of this manual before attempting assembly or operation of the dust collector Failure to comply may cause serious injury Unpacking 1 Finish removing all contents from the shipping carton 2 Report any damage to your distributor 3 Do not discard any shipping material until after the dust collector has been assembled and is running properly Contents of the Shipping Carton Plastic Cover Motor Fan Assembly Hose Owner s Manual Warranty Card Filter Hose Clamp Plastic impeller guard Metal Deflector Elbow Harware Package e oho eh e eh eh Tools Required for Assembly 2 10mm Wrenches or sockets 1 2 Cross Point Screw Driver The JET DC 650TS does not come with a collector can You can use the JET two stage dust collector on a variety of round metal and plastic collector cans The outer diameter of the trash can should be approximately 20 1 4 24 1 4 to fit properly Use the proper type hose C Fig 5 to connect the dust collector to the machine being operated Dryer vent hose is not acceptable for this purpose Contact your nearest JET distributor for the full line of JET Dust Collector Hoses and Accessories Customize your installation and obtain maximum performance with JET s dust hoods hoses clamps fittings and blast gates
13. t accompany the merchandise If our inspection discloses a defect we will either repair or replace the product or refund the purchase price if we cannot readily and quickly provide a repair or replacement if you are willing to accept a refund We will return repaired product or replacement at JET S expense but if it is determined there is no defect or that the defect resulted from causes not within the scope of JET S warranty then the user must bear the cost of storing and returning the product This warranty gives you specific legal rights you may also have other rights which vary from state to state The JET Group sells through distributors only Members of the JET Group reserve the right to effect at any time without prior notice those alterations to parts fittings and accessory equipment which they may deem necessary for any reason whatsoever 11 12 13 14 15 16 17 18 19 20 21 22 A WARNING Read and understand the entire contents of this manual before attempting assembly or operation Do not use this machine until proper training and knowledge has been obtained Do not leave Dust Collector when plugged in Unplug from outlet when not in use and before servicing Do not use outdoors or on wet surfaces Do not allow to be used as a toy Close attention is necessary when used near children Use only as described in this manual Use only manufacturer s recommended attachments Do not use with damag
14. tach the grounding clip A Fig 6 to the metal part of the filter This will prevent static electricity from building up in the filter Fig 3 Electrical Connections A WARNING All electrical connections must be done by a qualified electrician All adjustments or repairs must be done with the dust collector disconnected from the power source unplugged Failure to comply may result in serious injury The DC 650TS dust collector is rated 115V 230V Prewired 115V If you want to run the DC 650TS on 230V refer to the wiring diagram found on the inside of the Switch box cover A Fig 4 Before hooking up to the power source make sure that the switch is in the off position Turning the Machine On amp Off Note Before hooking up to the power source make sure that the switch is in the off position 1 The dust collector can be turned on by flipping the switch B Fig 4 into the on position 2 There is a removable key in the tip of the switch that can be removed in the off position When the key has been removed the dust collector cannot be used Maintenance A WARNING Never perform maintenance on this machine before turning switch off and removing plug from power source unplug Failure to comply may cause serious injury Motor Make frequent inspections of the motor cover C Fig 4 and blow out with low pressure air hose or vacuum any accumulation of foreign material in order to maintain
15. uipped with an electric cord having an equipment grounding conductor and a grounding plug The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances Do not modify the plug provided If it will not fit the outlet have the proper outlet installed by a qualified electrician Improper connection of the equipment grounding conductor can result in a risk of electric shock The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment grounding conductor If repair or replacement of the electric cord or plug is necessary do not connect the equipment grounding conductor to a live terminal Check with a qualified electrician or service personnel if the grounding instructions are not completely understood or if in doubt as to whether the tool is properly grounded Use only three wire extension cords that have three prong grounding plugs and three pole receptacles that accept the tool s plug Repair or replace a damaged or worn cord immediately 115 Volt Operation As received from the factory your dust collector is ready to run at 115 volt operation This dust collector when wired for 115 volt is intended for use on a circuit that has an outlet and a plug that looks like the one illustrated in A A temporary adapter which looks like the adapter as illustrated in B may be used to connect this plug to a two pole
Download Pdf Manuals
Related Search