Snell Acoustics AMC 720 Speaker System User Manual
Contents
1. O ec Snell Setting the Dispersion Switch The illustrations below show the recommended Dispersion Switch setting for most common placement options for the AMC 800 Horizontal Placement Placement SP amp 88 7 E Gol Gol 65 95 E Note When the AMC 800 is used as a center channel speaker and is placed horizontally the dispersion switch may be set in either position INSTALLATION INSTRUCTIONS IMPORTANT This manual assumes that the installer possesses skill in the proper use of hand and power tools knowledge of local building and fire codes and a familiarity with the environment behind the wall or ceiling in which the speakers will be installed Optional preconstruction brackets are available for each model PAINTING THE SPEAKERS If you intend to paint the speakers it is best to do so before installation 1 Remove the speaker grille 2 Mask the baffle 3 After painting carefully remove the paint mask Note Custom paint and grilles are available for an extra charge PREPARING FOR INSTALLATION Map out the wiring paths from the speakers to the amplifier We recommend 16 gauge wire for runs up to 25 feet and 14 gauge wire for lon2. So the AMC 900 should be installed where the null plane will run through the primary listening area This can be achieved either with the AMC 900 installed in a side wall with the long axis of the speaker oriented vertically or on the ceiling with the long axis of the speaker oriented across the width of the room AIMING THE DPT AMC720 AMC 760 and AMC800 only In addition to providing an extremely clean wide range response the DPT have the added feature of an adjustable waveguide in 45 degree increments This unique Snell feature provides the opportunity to toe in conventionally mounted in wall systems or compensate for the less than ideal placements that occur in the real world This feature will greatly improve imaging To adjust the DPT rotation remove the four wood screws with a 5 64 allen driver and rotate the driver to the desired positions Three examples of how the DPT waveguide tweeter can be rotated in 45 increments MULTIPLE DISPERSION PATTERNS AMC 800 only The AMCB800 can be set to reproduce two dispersion patterns You determine the dispersion pattern by selecting which of the two bass units will operate as the midbass driver The dispersion pattern can be seen as an ellipse whose length is a line perpendicular to the tweeter midbass combination as shown below Dispersion Pattern A Dispersion Pattern B eibi
3. 1 configuration not 7 1 or EX they are best mounted to the sides of the listening area This means straight to the sides of the listener or in line with the primary row of seating plus or minus 15 degrees This is preferred over back wall mounting for several reasons It places the surrounds at locations where the difference between left ear and right ear discrimination is at a maximum This gives the maximum sense of envelopment or being surrounded by sound Rear mounted speakers force a huge angular gulf between the front primary speakers and the rear speakers The sound image is inherently discontinuous Also front to rear aural discrimination is not very d strong Differentiation between front and rear speakers will not be as strong as the effect of adding speakers to the side 7 1 or EX systems that use side and rear speakers together overcome all of these obstacles give both maximum v eg envelopment and a more continuous Optional Direct Radiation surround effect Surround Speaker Locations A second factor to consider is the evenness of sound coverage over the seating area Most surround processors have features for setting the balance of all channels A circulating noise signal is adjusted in each channel until the apparent or measured sound level is even Of course moving to another seat will shift this balance somewhat Well placed surround speakers will minimize the level variation from seat to seat The
4. best way to achieve evenness is to increase the distance of the surround speakers from the listening area Mount them high on the side walls or even on the ceiling As a good rule of thumb surrounds should be on the side walls at least one foot above the height of a standing listener If the speakers are ceiling mounted they should be close to the side walls well away from an overhead position If a large theater room with three or more rows of seats is planned then more than one pair of surround speakers should be used to give more even coverage and a more diffuse sound field We recommend that a pair of surrounds be used for every other seating row the first the third the fifth etc This follows standard cinema practice Special Considerations for the AMC 900 Placement of a dipole surround speaker such as the AMC 900r requires another consider ation For a dipole to give a properly diffuse sound the listeners should be on or near the null plane Imagine a line running down the middle of the front of the AMC 900r along the longer dimension between the two tweeters and across the center of the woofer A plane sticking straight out from this line at 90 degrees to the wall defines the null plane For any listener on this plane the output of the two tweeters and the midrange will be at maximum cancellation A listener at this position will hear the speaker only via multiple wall reflections This is why the dipole sounds diffuse
5. these two distances to the 45 60 primary listening location ld liis Ideally the front channel speakers should be installed at the same height as the ears of a seated listener Try to keep the V front channel tweeters within two EE vertical feet of that height If speakers must be installed more than 2 3 feet above or below the ideal position take advantage of the DPT rotating feature For example aim the tweeter downward when the speakers are mounted high on 900 the wall For more information refer to the Aiming the DPT section PLACEMENT OF THE SURROUND SPEAKERS There are many opinions about where surround or rear speakers should be mounted The following is based on the findings of the best academics and on our experience with many installations These placement recommendations apply to all the AMC models whether you are using AMC 900r dipole surrounds or AMC 720 AMC 760 or AMC 800 direct speakers When selecting installation locations for the AMC 720 AMC 760 or AMC 800 remember that you can increase the diffusion of their sound by aiming their DPT drivers away from the listening area see the Aiming the DPT section The tweeters can be aimed toward a reflecting surface or a surface that will scatter the sound such as a shelf full of books or other irregular surface The AMC 900 tweeters should not be repositioned If two surrounds are used in a standard 5
6. 50W 4 ohms 6 ohms 90dB SPL 87dB SPL 1 Aluminum dome ferrofluid cooling and heatsink Steerable Directed Power waveguide 61 2 165mm copolymer with butyl rubber surround 600 Hz 3kHz 21 2 way Specialty adhesive between two 1 4 layers of HD fiberboard White cloth over MDF frame 231 4 x 131 4 x 33 4 inches 590 x 336 x 95mm 22 x 12 inches 559 x 305mm White trim suitable for painting 22 Ibs 10kg each AMC800 2 1 aluminum dome ferrofluid cooling and heatsink Directed Power waveguide in dipole configuration 31 2 Midrange edge mounted in dipole configuration 61 2 inch 165mm copolymer with butyl rubber surround 400 Hz 2 5 kHz 12dB octave Specialty adhesive between two 1 4 layers of HD fiberboard White cloth over MDF frame 231 4 x 131 4 x 33 4 inches 590 x 336 x 95mm 22 x 12 inches 559 x 305mm White trim suitable for painting 22 Ibs 10kg each yi E E E AMC900 INTRODUCTION WHAT IS A HIGH END IN WALL The new Snell AMC series units bring a novel approach to the design and construction of in wall loudspeakers expanding the boundaries of in wall performance Our primary goal was to develop loudspeakers th
7. Owner s Manual AMC 720 760 800 900r SPECIFICATIONS AMC720 AMC760 Frequency Response 3dB 65 Hz 20 kHz 62 Hz 20 kHz Recommended Amplifier 10 125W 10 150W Nominal Impedance 8 ohms 8 ohms Sensitivity 2 83v at 1m 87dB SPL 89dB SPL Tweeter s Midrange Bass Driver Crossover Point Composite Baffle Grille Dimensions HxWxD Rough Opening Cutout HxW Finish Weight 1 aluminum dome ferrofluid cooling and heatsink Steerable Directed Power waveguide 51 4 inch 132mm copolymer with butyl rubber surround 2 7 khz Specialty adhesive between two 1 4 layers of HD fiberboard White cloth over MDF frame 14 x 81 2 x 33 4 inches 356 x 216 x 95mm 127 8 x 73 8 inches 327 x 187mm White trim suitable for painting 21 Ibs 9 5kg pair AMC720 Custom paint and grilles are available for an extra charge 1 aluminum dome ferrofluid cooling and heatsink Steerable Directed Power waveguide 61 2 inch 165mm copolymer with butyl rubber surround 2 7 khz Specialty adhesive between two 1 4 layers of HD fiberboard White cloth over MDF frame 17 x 101 2 x 33 4 inches 432 x 267 x 95mm 157 8 x 93 8 inches 403 x 238mm White trim suitable for painting 23 Ibs 10 5kg pair e g AMC760 AMC800 9 65 Hz 20 kHz 78 Hz 20 kHz 10 200W 10 1
8. at delivered performance that was as close as possible to that of our highly regarded freestanding loudspeakers like the K 5 mk2 and E 5 mk2 To do this several issues had to be addressed The bass performance of conventional loudspeakers mounted in wall cavities is very unpredict able Cavity volume can be large which should be good for bass performance However with one very short dimension approximately 4 and one very long dimension up to 8 the wall cavity takes on the characteristics of a closed end organ pipe This creates a strong resonance that tends to null out the bass Lining this cavity with fiberglass will reduce the O of the notch but not restore the bass What is needed is a defined volume of a more regular size This is best done with fully enclosed in wall speakers The Snell AMC loudspeaker enclosure is a thin but strong aluminum tub It is both damped and braced This largely contains the back radiated sound of the woofer within the enclosure An added benefit of containing the woofer output is a reduced chance that resonances will be excited in the house walls Furthermore sound bleed through to adjacent rooms is reduced To minimize resonances in the Snell enclosure the speaker baffle uses a technique first pioneered on our 5 and XA series loudspeakers The baffle is a three part composite with MDF fiberboard outer layers around a thin but highly effective damping layer This controls the panel resonances of
9. cant construction work is being done near the speaker installation location 1 Make an appropriate size speaker mounting cutout in the wall material 2 Run the wire from the amplifier to the cutout Allow an extra foot of wire at the cutout Strip 1 2 12mm off the wire and tightly twist the wire strands together 3 Remove the speaker grille 4 Insert the speaker wires into the spring terminal binding posts Important Typically one side of the wire is smooth Connect this side to the black speaker terminal The other side has a rib or stripe Connect this to the red speaker terminal Connect wire at the amplifier in the same way Failure to do so will result in degraded sound Warning prevent electrical shock always switch off the amplifier or receiver when making connections to the speaker system Continued 5 Place the speaker into the rough opening 6 Level the speaker and tighten the screws being careful not to over tighten them See diagram below for details Turn the mounting ls N Ea clamps against the enclosure then place the speaker in the mounting hole Use a phillips head screwdriver to deploy the mounting clamps Q and pull them against the back of the drywall 7 Replace the speaker grille Note The AMC 900 is sold in pairs the cabinet near the input terminals is a temporary label to specify screen direction The response will be s
10. e Snell Acoustics will repair for the original owner any defect in materials or workmanship that occurs in normal use of the speaker system without charge for parts and labor Your responsibilities are to use the product according to the instructions supplied to provide safe and secure transportation to an authorized Snell Acoustics service representative and to present proof of purchase from an authorized Snell dealer in the form of your sales slip when requesting service Excluded from this warranty is damage that results from abuse misuse accidents shipping repairs or modifications by anyone other than an authorized Snell Acoustics service representative This warranty is void if the serial number has been removed or defaced This warranty gives you specific legal rights and you may also have other rights that vary from state to state If Service Seems Necessary Contact the dealer from whom you purchased the speaker system If that is not possible call us at 978 538 6262 or write to Snell Acoustics 300 Jubilee Drive PO Box 3717 Peabody MA 01961 3717 We will promptly advise you of what action to take If it is necessary to return your speaker system to the factory please ship it prepaid in the original factory packaging Please note that Snell Acoustics will not be held liable for shipping damage due to improper packaging After it has been repaired we will return it freight prepaid in the U S or Canada 2002 Snell Acou
11. ger runs Be sure the speaker wire does not rest or rub against any sharp or pointed objects The speakers should be mounted on a flat surface to form a good seal between the speaker flange and the mounting surface When connecting more than two speakers per amplifier channel you should use series parallel wiring In all cases make certain that the total impedance does not fall below the amplifier s rating If you are not sure contact your Snell Acoustics dealer You will Need 1 A utility knife an electric jigsaw or other means of cutting a hole in the mounting surface 2 A 2 Phillips screwdriver 3 A wire cutter or stripper for preparing the speaker wires With the supplied hardware the speaker can be installed in existing walls or ceilings from 1 2 12mm to 11 2 38mm For thinner walls you will need to use spacers for the mounting legs contact your Snell dealer for this optional rubber part INSTALLATION For convenient installation the Snell AMC720 AMC760 800 and AMC 900 use a dog leg mounting system see illustrations below This provides a quick and clean install Further more the dog legs can be removed if a particular situation requires to speaker to be directly attached to a stud Note As an added security feature the speaker tubs can be pre mounted without the baffle drivers and crossovers installed This will allow you to protect the delicate speaker components from debris if signifi
12. lightly superior in this direction Install the two AMC 900ruy s so that the arrows BOTH point toward the screen If listeners are not going to be located on or near the center axis of the speaker the speaker should be oriented with the arrow toward the listener location even if this is away from the screen LISTENING LEVELS AND POWER HANDLING The power recommendation for the system assumes you will operate the amplifier in a way that will not produce distortion All speakers can be damaged by even a modest amplifier if it is producing distortion If you hear a gritty noise or other signs of strain turn down the volume Prolonged or repeated operation of your speakers with a distorted signal can cause damage that is not covered by the warranty It is especially important that you do not overdrive the bass capability of smaller speakers Watch for noises such as pops caused by the music s bass line Use of the loudness control and or full bass boost at louder volumes is likely to overdrive the woofer Use such controls sparingly HOW TO CARE FOR YOUR SPEAKERS gt Use a soft terry cloth towel slightly dampened with water glass cleaner or a diluted mild detergent The towel should be just damp enough to wipe the surface clean without leaving a trail of moisture gt Do not use abrasive cleaners or any cleaner containing chemicals harsher than those found in glass cleaner LIMITED WARRANTY For five years from the date of purchas
13. re retained Highly coherent in phase crossover networks ensure a seamless blend from driver to driver Drivers are designed for smooth wide range response and low distortion Long sessions of listening and adjusting give each system that special characteristic Snell sound Finally that Snell sound is guaranteed in every production pair by Snell s proprietary 0 5dB production tuning techniques PLACEMENT OF THE FRONT CHANNEL SPEAKERS A home theatre system includes three loudspeakers placed across the front of the listening room The distance between the left and right speakers determines the width of the stereo image If the speakers are placed too close together the image will be too narrow too far apart and the blend will suffer creating a hole in the middle When properly placed your speakers will create a continuous virtual image from left to right with an illusion of sound outside in front of and behind the speaker systems We recommend an angular separation between 45 degrees and 60 degrees when viewed from above This is equivalent to a separation between the speaker systems that is about 85 of the distance to either of the speakers Creation of sounds between the speakers AMC 800 requires some precise placement The I M distance from the left speaker right fe speaker and center channel to the listener location should all be as equal as C possible We advise using a tape measure V 7 to equalize
14. stics All Rights Reserved Specifications are subject to change without notice Covered by patents issued and or pending Part 4542 1026 Snell 300 Jubilee Drive POB 3717 Peabody MA 01961 3717 phone 978 538 6262 fax 978 538 6266 email info snellacoustics com www snellacoustics com
15. the baffle that can obscure midrange clarity As we have found with our freestanding loudspeakers a better loudspeaker cabinet means a better sounding loudspeaker Conventional in wall speakers also suffer from poor stereo imaging Freestanding speakers can be angled inward to produce a better central image and make listening position much less critical In wall speakers obviously cannot be angled in this way Some in wall speakers use a pivoting post mounted tweeter in attempt to overcome this limitation The pivoting mechanism produces reflections that adversely affect the tweeter s response and sound Also the small baffle area of the pivoting tweeters means that only the highest frequencies can be angled inward The Snell solution is a unique tweeter that incorporates a waveguide with a fixed 20 degree angle The DPT Directed Power Tweeter waveguide design controls reflections to ensure smooth response The waveguide is also large enough to function effectively over the full range of the tweeter The DPT driver can be easily unfastened and rotated to any of eight positions in 45 degree increments This together with the designed in angle of the driver lets you direct the sound inward to focus a stereo image Or the sound can be directed away from the listening area to produce a more diffuse sound field when the AMC 720 AMC 760 or AMC 800 are used as surround speakers In addition to these unique solutions all traditional Snell attributes a
Download Pdf Manuals
Related Search