Silvercrest KH 2155 Universal Remote User Manual
Contents
1. AY FAV CHOIS EXIT FRP CHN AY FRP LH TAY FAV CHI DEL ALL ex SURE DELET jos DELETED EXIT Programming FAV channels Your favourite stations are saved as follows 1 Press the desired device button for the device to be programmed 2 Hold down the SET button for a little longer than 3 seconds 3 With the or button select FAV CH and confirm with the OK button 4 In the LCD display appears SETUP Confirm with the OK button In the LCD display appears FAV CH 1 5 With the 4 or v button select the desired FAV channel and confirm with the OK button In the LCD display 9 appears SELECT KEY 6 Now enter with the number buttons O the first stations that you want to save in the respective FAV CH for two digit numbers first press the button After you have pressed the sixth button of the station selection in FAV channel the setting will be automatically saved In 20 the LCD display appears SUCCESS followed the next FAV CH All buttons will be ignored except OK EXIT FAV CH the number buttons and Note The URC saves the button presses Therefore if you save two digit stations their max count is reduced to 2 1x 2 number buttons 3 pressed buttons per station 7 Press the OK button to save the FAV CH In the LCD display appears SUCCESS followed by the next FAV CH 8 T2. uwana 28000017 066 0598 196 ID uoo sspuJjeduiox n 8919 8 0780 04 9 8 0 80 7191 530 46 ejoq euoudeje gt e2D d epooisod 814 01 HAS Apupy dijs 5 05 ans exow EIU 195 YONO 426 espe d enpe oud ain doa 994 4502 Japio 8916 TOULNO D ie upijddp 5 siu Description of fault
3. The majority of manufacturers use several different codes for the remote control You must now ascertain which of the available codes is best suited to your device The current code is displayed underneath the brand name Point the remote control to the current device and press the function buttons to test the code except lt 6 OK or the number buttons If most of the buttons function press the OK button 9 to save the setting In the LCD display appears SUC CESS Now the mode BRAND SRCH appears again 10 If however none or only a few of the buttons function select with the 4 or button the next code and test again as described in step 8 11 You can end the setting mode with any device button except after step 5 With the EXIT button you will move one level upwards in the menv 12 Repeat these operational steps for all devices that you would like to control with the remote control Programming by manual code input In this mode the remote control can be programmed by direct input of a code number Please extract the necessary code number from the accompanying code list In the event that the new code is invalid the last valid programmed code will be restored l 2 Hold down the SET button for a little longer than 3 seconds In the LCD display appears CODE SETUP Press the OK button BRAND SRCH now appears in the LCD display Press the or button
4. in the display of the URC 8 If in the LCD display SUCCESS appears process successful you can teach further buttons begining with step 5 If FAILED appears process unsuccessful repeat the process in any case from step 5 9 To stop the learn process any device button O can be pressed If in the LCD display is shown WAITING then stopping can only be carried out with the EXIT button After which the URC again returns to the LEARN KEY mode see step 4 Clear programmed button 1 Press the corresponding device button 2 Hold down the SET button for a little longer than 3 seconds 3 With the gt or button select LEARNING and con firm with the OK button In the LCD display appears LEARN KEY 4 With the 4 or button select DELETE KEY and con firm with the OK button In the LCD display appears SELECT KEY 5 Press the taught button that is to be deleted In the LCD display 69 appears SURE DELET are you sure 6 Confirm the delete process with the OK button In the LCD display appears DELETED and then again SELECT KEY 7 Repeat steps 5 6 to delete further buttons 8 Press any device button O to end the mode Delete all of a device s programmed buttons 1 Hold down the SET button for a little longer than 3 seconds 2 With the 4 or button select LEARNING and con firm with the OK button In the LCD display appears LEARN KEY 3 With
5. until CODE SET is shown in the LCD display Then press the button In the LCD display appears the last programmed device and the code used Press the desired device button i e VCR The target device now blinks and waits for your confirmation With the OK button confirm the selected device Now the first digit of the code blinks and waits for your code input Enter the 3 digit device code with the number buttons and confirm the entry with the OK button If the entered code is valid for the selected device type then the code will be saved In the LCD display appears SUCCESS and then again CODE SET In the event of failure the LCD display shows NOT FOUND and waits for a new code input Then you repeat step 6 For many combi devices you must enter 2 codes from the accompanying list i e one for the TV section and one for the DVD section If the code of a combi device i e TV DVD is shown in the list as XXX XXX then apply the first 3 numbers for the device named first in the device denomination and the last 3 numbers for the device named second DVD With the EXIT button you can end the CODE SET mode Tips Should AUX be selected as device then step 6 after the code you must press a fourth button to communicate the device type to the remote control 0 3 SAT CBL 1 VCR 4 DVR PVR 2 DVD CD 5 AUDIO The AUX device appe
6. Laser Laser class 1 Power supply Batteries 2 x 1 5 V type AAA LRO3 micro Batteries not supplied Important Warranty Notices You receive a 3 year warranty for this device as of the pur chase date Should you have grounds for complaint in spite of our high quality standards please contact our Service Hotline In the event that processing of your complaint is not possible by telephone here you will receive processing number RMA number as well as an address to which you can send your device for repoir under warranty 27 In the case of a shipment please enclose copy of the purchase receipt sales slip The device must be securely packed and the RMA number clearly visible Products sent in without the RMA number cannot be processed D Note The warranty provisions cover only material or factory defects The warranty is not valid to parts subject to wear and tear for damage to breakable parts such as switches or rechargeable batteries This product is for private use only and is not intended for commercial use The warranty is void in the case of abusive and improper handling use of force and internal tampering not carried out by our authorized service branch Your statu tory warranty claims are not restricted by this warranty 28 15 uoo sspujeduioxoer Addo sejo1 02
7. Note With the button ALL OFF all off all devices can be automatically switched off For this press the ALL OFF button twice within 2 seconds This will only function under the fol lowing circumstances 1 A visible connection exists between all the devices and the URC 2 Automatic code search brand code search and MACRO function are not active 3 All target devices must be suitable for remote control switch off To automatically switch on all devices again press the button once more twice within 2 seconds 23 Automatic station redirecting D Note 1 With this function all stations can be accessed in rapid succession without the necessity of manual redirection 2 This function is only available for TV 3 The function is then also for AUX available if a TV device is defined here 4 Hold down the button CH or CH for 3 seconds After which the Infrared symbol blinks every 1 5 seconds and the next station is shown 5 The remote control now continually sends every 1 5 sec onds the command CH and or CH until a button is pressed The background illumination if activated goes out briefly with each Infrared transmission 6 Press any other button to end the automatic station redirecting Alternative button allocation in teletext mode If the remote control is in teletext mode by pressing the button TTX ON OFF the buttons CH CH and play back buttons serve as controllers
8. Press the corresponding device button to set the remote control to the correct mode c The batteries must have enough voltage and be properly installed c It is possible that you are using the wrong code Start the brand code search the automatic code search or the direct code input manual 25 The remote control does not change the station on the device c Press the corresponding device button to set the remote control to the correct mode gt In the event that the original RC does not have a button change the programme with the CH buttons 9 or the number buttons If this also does not work the child protection for this device could be activated Some of the remote control buttons do not function properly c It is possible that your universal remote control does not have all of the functions that are on the device s original remote control c It is possible that you have not programmed in the optimal code Search for a code that supports more of the target device s functions The remote control stops reacting after a button is pressed gt The batteries must have enough voltage and be properly installed gt Point the remote control towards your device The LCD display shows nothing gt The batteries must have enough voltage and be properly installed gt The contrast could be set too low Then increase the contrast setting Disposal ps Do not dispose of the device in
9. controlled i e VCR 5 Point the remote control to the device and press the OK button to start the search The Infrared symbol 9 blinks which shows the emission of Infrared commands 6 If the device reacts by switching off press the PAUSE button to stop the code search 7 To test whether you have conducted the search fast enough press once button then again the button If the device reacts again you have most probably found the correct code 14 8 If the device does not react again carry on switching every 1 5 seconds with the button to the previous code until the device reacts 9 Then press the OK button to save the code The LCD display shows SUCCESS and then returns again to the AUTO SEARCH mode 10 Press the EXIT button twice to exit the programming mode 11 Check to see if the majority of your device s functions can be controlled with the remote control In the event that a few functions are not working you can start the automatic code search again beginning with step 1 Tips If the PAUSE II button is pressed during the automatic code search the code search stops Pressing on the PAUSE II button again allows the device to take up the search once more 1 During an active code search all buttons except OK PAUSE and EXIT O will be ignored 2 If the EXIT button is pressed during the code search the search will stop and the AUTO SRCH
10. every button press the LCD display 69 will stay illuminated for 8 seconds Press the LIGHT button again to deactivate the illumination function Buttons D Note All the functions described here can of course only be used if they are supported by the device being controlled O ALL OFF button ALL OFF Switch device on off press twice within 2 seconds to switch all devices on off SET button 9 SET Hold down for 3 Seconds to access the SETUP menu Device buttons The device buttons are used to select which device should be operated TV Television SATICBL Satellite receiver cable AUDIO Audio device Computer VCR Video recorder DVD CD DVD or CD player DVRIPVR Digital Personal video recorder AUX Additional device Illumination button LIGHT Press the LIGHT button to illuminate the gt display CH buttons O Change the reception channel VOL buttons 9 Set volume Volume TTX ON OFF button Switch teletext on off Number buttons 2 3 4 5 6 7 8 9 0 Enter programme and device code numbers RECALL button RECALL Accesses the last selected programme slot Button for one two digit programme numbers For two digit programme numbers first press the button then via the number buttons enter the programme number When pressed again the display becomes single digit once more Playback buttons and teletext function buttons The playb
11. status is again accessed without the code being saved 3 Should the correct code be found however the device s original remote control did not have a POWER button then it is possible that the device cannot be switched on or off remotely Then try the buttons CH or MUTE 4 If the automatic search has reached the end of the code list it stops there Then press the EXIT button to return to the AUTO SRCH mode and start again with step 4 5 If you want to programme an AUX device by automatic code search the device type must first be defined by direct code input After which you carry out the auto matic code search from step 5 Learn function The Universal remote control URC can learn and save button signals of an original remote control If the URC does not work after applying the programming methods already described or cannot carry out all commands please attempt to teach the URC with the help of the original remote control Use new batteries for the URC and the original remote control Maintain a distance of at least one metre from other light sources The light sources could disrupt the infrared trans mission Place the URC and the original remote control at a distance of 25 to 55 mm from each other on an even surface so that the Infrared diodes are facing each other Tips 1 Do not use the following buttons for the learn function all device buttons LIGHT MACRO FAV CH
12. A 5 55 GMBH BURGSTRASSE 21 D 44867 BOCHUM www kompernass com ID NR KH2155 01 09 V4 UNIVERSAL REMOTE CONTROL UNIVERSAL REMOTE CONTROL Operating manual 2155 INDEX Important safety instructions Device overview First use Unpacking the device checking the package contents Inserting the batteries Operating elements LCD display Buttons Configuration Setting the time Adjust contrast Background Illumination Child protection system SETUP System settings Programming the remote control Programming by brand code search Programming by manual code input Programming by automatic code search Learn function Code learn function Clear programmed button Programming Macros Favourites channel Volume control Vol Mute switching Further volume control functions except PC Back to volume control Additional functions All OFF Automatic station redirecting Alternative button allocation in teletext mode Alternative button allocation in PIP mode Faults Remedies Disposal CE Conformity Importer Technical data Important Warranty Notices PAGE noli ro TP fp lt 1 TPMT MOTO Of fp OTP NT 24 25 25 26 27 27 27 27 UNIVERSAL REMOTE CONTROL KH2155 Read the operating instructions carefully before usi
13. EXIT 2 When teaching please do not release the button of the original remote control until SUCCESS or FAILED appears in the LCD display 3 If whilst teaching when the display is showing WAITING still no button on the original remote control is pressed after 25 seconds the LCD display shows FAILED followed by SELECT KEY 4 If the memory is full the LCD display 9 shows FULL and the learn mode will end 5 Whilst the LCD display is showing WAITING in the learn mode the mode can only be ended with the EXIT button 6 During the learn mode or when the taught buttons are deleted the current mode can be exited with any button except when WAITING is showing 7 With the EXIT button you return to the previous status Code learn function 1 Press the desired device button 2 Hold down the SET button for a little longer than 3 seconds 3 With the or button select the menu LEARNING and then press the OK button 4 In the LCD display appears LEARN KEY Then press the OK button In the LCD display 6 appears SELECT KEY 5 First press the button on the URC that is to be taught In the LCD display 6 appears WAITING The URC now waits for the Infrared signal from the original remote control 6 Point the Infrared sensors of both remote controls towards each other 7 Now hold down the desired button of the original remote control until SUCCESS or FAILED appears
14. FAV CH button FAV CH j Accesses your previously programmed favourite station AV button 2 Switch to the AV input i Configuration Setting the time The LCD display shows you the time of day You set this as follows l 2 Hold down the SET button for a little longer than 3 seconds With the or button select CONFIG and confirm with the OK button In the LCD display appears TIME SETUP Confirm with the OK button The LCD display now shows TIME and the first number of the hour display blinks With 4 or place the cursor on the position in which you want to make an entry and press the number buttons O to set the hour and minutes The switching be tween and PM you undertake with the or but ton Thereby AM stands for ante meridium morning 0 00 to 12 00 o clock and PM stands for post meridium afternoon 12 00 to 0 00 o clock With the OK button O you save the setting In the LCD display appears SUCCESS and the previous mode is accessed again In the event of an error the LCD display shows ERROR To exit this menu press repeatedly the EXIT button until the standard display appears in the LCD display Adjust contrast You can set the display s contrast as follows 1 2 3 Hold down the SET button for a little longer than 3 seconds With the gt button select CONFIG and confirm with t
15. ack buttons 69 control devices such as DVD CD players and video recorders Record Stop Playback Record Wind Rewind m Start playback Stop playback Wind forward n teletext operation the buttons have the following functions pa Access time Cancel page access Enlarge page presentation D Access Index page Stop automatic page forwarding for multi page teletexts IHI Mystery button In addition the CH buttons 69 control the following teletext functions 1 Leaf one page forward Leaf one page backward GUIDE button 9 c The GUIDE button accesses the device s electronic programme guide Fi Arrow buttons Move up right left and down in menus For control of the Picture in Picture function EXIT button 9 Move a level backward in the menu INFO button Superimpose programme information OK button You can confirm a menu selection with the OK button MENU button Access the menu of the controlled device SWAP button SWAP control the A B repeat function in DVD CD modes To switch between the main and second image in PIP operation PIP button 9 PIP to access end the TV s picture in picture mode With SAT CABLE the PIP button serves as the video format selector MACRO button MACRO The MACRO button followed by a number button 1 6 activates the previously saved chain of commands Mute switching 9 Switch sound on off
16. ars in the LCD display as AUX1 which is normal If the AUX device has been set with another programming method please specify it first as AUX device in the direct code entry Example The television shall be defined as an AUX device For this in step 6 press as the fourth number the O so that afterwards the television can be programmed with the brand code search or the automatic code search Programming by automatic code search This process can take several minutes per device since all codes for the selected device have to be gone through Therefore this method should only be used when the device cannot be programmed via brand code search or direct code input or if your device is not listed at all in the manu facturers directory with device code list A PC will not be considered a device with the automatic search Follow the steps listed below to carry out programming by means of the automatic code search 1 Switch the device that is to be controlled with the remote control on With VCR DVD CD devices please insert a tape and or disc 2 Hold down the SET button for a little longer than 3 seconds 3 In the LCD display appears CODE SETUP Press the OK button BRAND SRCH now appears in the LCD display Press the or button until AUTO SRCH is shown in the LCD display Then press the OK button O to access the automatic code search mode 4 Press the device button O that corresponds to the device to be
17. button There are 6 Macro memory slots available for you Macro programming overview MACROI e SETUP SELECT KEY SURE DELET EXIT DELETED AY E TE Macro programming including PC For Macro programming proceed as follows 1 Hold down the SET button for a little longer than 3 seconds 2 With the 4 button select MACRO and confirm with the OK button 3 With the 4 or gt button select MACRO T to MACRO and confirm with the OK button 4 In the LCD display 0 appears SET UP Confirm with the OK button 5 In the LCD display 9 appears SELECT KEY Now press one after the other the desired buttons starting with a device button If the sequence does not begin with a device button ERROR KEY wrong button appears in the LCD display and then SELECT KEY again 6 Save the entry with the OK button In the LCD display appears SUCCESS and then the Macro selection mode again 7 If you select a memory slot that is already occupied when you make the Macro programming selection step 3 the device reacts to your setup attempt with the notice MACRO HAS Macro occupied in the LCD display After which SET UP will be shown again Therefore you must first delete the memory slot before you can use it again How that is done you will discover in one of the next sections under Macro delete 8 Repeat the process from step 3 to create fu
18. by brand code search by automatic code search and by direct code input manual First you should use the brand code search since this method is the fastest way of programming if your device is itemized in the code list As second is recommended the direct code input followed by the automatic code search Programming by brand code search With this method you select the brand and code direct via the LCD display Observe the following operational references to programme the remote control 1 2 Press the device button for the device on which you want to programme the remote control except for PC Hold down the SET button for a little longer than 3 seconds In the LCD display appears CODE SETUP Press the OK button BRAND SRCH now appears in the LCD display Press the OK button Now appears the alphabetical first brand name from the list of preprogrammed devices With the buttons select the various brand names To make access easier you can skip directly to specific letters of the alphabet with the number buttons 2 gt 3 gt D 4 gt G 5 gt 6 gt 7 gt 8 gt 9 gt W example With button number 5 the display skips to the letter J The first brand is JVC If for example you own Kenwood brand device leaf with the button downwards until this brand name appears All brand names used here are trademarks of the corresponding manufacturer
19. ct now between ON child protection on or OFF child protection off With the OK button O you save the setting In the LCD display appears SUCCESS and then KIDS LOCK To exit this menu press repeatedly the EXIT button until the standard display appears in the LCD display SETUP System settings In the system settings you undertake the following Programming the remote control to the devices to be controlled Setting the time of day display contrast and child protection The learning of determined button commands Setting up Macros Assigning favourites etc SYSTEM SETUP overview 210 sec CODE SETUP ex BRAND SRCH 12 00 AY AUTO SREH AY CODE SET 210 CONFIGUE TIME SETUP CONTRAST av KIDS LOCK TV 210 sec LEARNING LEARN KEY 008 9 EXT AY DELETE KEY DELETE 0 DELETE ALL 210 sec MACRO ACRE 1 00 gU gx av MACRO 5 5 MACRO 4 AY ____ __ __ MACRO 2 2710 sec CH E SETUP 2 ex AY AY DEL ALL 210 sec VPT SETUP 0 00 2 EXT AY 210 BASIC 5 00 9 aye Programming the remote control 3 Programming methods are available for the remote control Programming
20. d with 1 5 Volt batteries Type AAA 1803 Carry out the battery change as quickly as possible Preset settings will remain saved for approx 1 minute If new batteries have not been installed within this time all of the settings will have to be carried out again The time of day will however in any case be deleted 1 Open battery compartment cover in the direction of the arrows 2 Insert the batteries as shown in the diagram and close the battery compartment The ICD display is activated as long as batteries are installed The following diagram shows the LCD display 6 after the batteries have been installed or changed iv 2 10 o Note If no LCD display is visible check the polarity of the batteries or install new ones Operating elements LCD display The LCD display is divided into fields Text field 9 Here is shown the currently selected device for example DVD TV or VCR Code field Here is shown the device code of the currently selected device Infrared symbol 9 Every time a button is pressed with which an infrared signal is to be sent the Infrared symbol illuminates Time field Here you can read the time of day Standard display TH 2 10 standard display of the LCD display consists of details of the current device i e TV the device code and the time of day Illumination If you press the Illumination button LIGHT with
21. for the teletext After deactivation of the teletext the buttons revert back to their usual functions Button Normal function Function in TTX mode Shift forward 1 Page forward 1 Programme slot Shift back 1 Page backwards 1 Programme slot Start playback Access index page Stop playback Stop page search Stop Stop automatic page playback change The function is only available in the European TV mode and your TV must have a teletext module Note 24 Alternative button allocation mode D Note The PIP function picture in picture is only available in the TV mode Your TV device must support this function You switch the PIP function on and or off with the PIP button If the remote control is in the PIP mode the following buttons serve as controllers for the PIP functions Normal function Function in PIP mode move up in the PIP menu move down in the menu TRI move left in the PIP size menu move right in the PIP position menu Faults Remedies Your device does not react to the remote control c Check the batteries They must have enough voltage and be properly installed c Firstly have you pressed the correct device button for the desired target device c Check to see that the correct code is programmed for the target device see section Programming the remote control The remote control is transmitting the commands in correctly gt
22. he OK button With the or gt button select CONTRAST and con firm with the OK button Q With the 4 button you set the contrast gt reduces the contrast 4 increases the contrast Display readout O highest contrast 15 lowest contrast With the OK button O you save the desired setting In the LCD display 69 appears SUCCESS followed by CONTRAST To exit this menu press repeatedly the EXIT button until the standard display appears in the LCD display 9 Background Illumination When the lighting circumstances are poor you can activate the display s background illumination Bear in mind that this will reduce the lifespan of the batteries 1 Press once the LIGHT button From now on the LCD display 69 will illuminate with each button press for approx 8 seconds Press this button once more to switch off the LCD display s background illumination Child protection system With the child protection system the channel buttons CH CH 0 9 can be locked for individual devices 1 2 Hold down the SET button for a little longer than 3 seconds With the or gt button select CONFIG and confirm with the OK button With the or button select KIDS LOCK and con firm with the OK button The LCD display shows the current device and always offers the setting OFF inde pendent of the current setting With the 4 or button sele
23. lete mode 3 Individual FAV channels cannot be deleted they can only be overwritten 21 Volume control Vol Mute switching Press the VOL button to increase the volume With the VOL button you reduce the volume To mute the sound press the E button A further press of this button turns the sound back on All devices use their own volume control if available If a video device such as a VCR or DVD player does not have its own volume control the volume control of the television is automatically used Note 1 The volume control does not function in the audio PC and AUX modes 2 The volume control does not function if the relevent device has its own volume and mute control functions exceptions are possible Further volume control functions except PC As mentioned above the volume controlling takes place automatically If however you want to programme a device from another device proceed as follows Note The devices audio and PC do not have this function 1 Hold down the SET button for a little longer than 3 seconds 2 With the 4 or gt button select VPT SETUP and confirm with the OK button In the LCD display appears TO DEV to the device 3 Now press the button for the device O i e VCR to which the volume command should be sent After which appears FROM DEV from device in the LCD display 9 the device from which the command is sent 4 Now
24. ng the device for the first time and preserve this booklet for later reference Hand over the instruction manual to whomsoever you might pass the device on to Important safety instructions Proper use Children may only operate the remote control under adult supervision The universal remote control can replace a maximum of eight remote controls It can only be used for entertainment electronics with infrared receivers The functions of the universal remote correspond to those of the original remote controls The universal remote control is intended for private use It is not suitable for commercial use Any other use is considered improper use The manufacturer declines to accept responsibility for damage s arising from improper use There is danger of injury in the event of improper handling of batteries Batteries must be handled with special care Take note of the following safety instructions Take the batteries out of the battery compartment as soon as they are depleted Do not throw batteries into a fire Never subject batteries to high temperatures If you will not be using the device for a long period of time remove the batteries to prevent them from discharg ing Explosion hazard Non rechargeable batteries must never be recharged Do not open the batteries or short circuit them Battery acid leaking from a battery can cause inflamma tion of the skin In the event of contact with the
25. o exit this menu press repeatedly the EXIT button until the standard display appears in the LCD display Note new programming of the FAV channels overwrites the old settings The input of the channel numbers can vary according to the model and brand of the selected device Accessing FAV channel To access the previously programmed favourite station press the FAV CH button The URC now accesses one after the other the pro grammed stations from the favourites channel with the low est number Press the FAV CH button again and the sta tions from the next favourite channel up is accessed Delete All FAV channels To delete all the FAV channels proceed as follows 1 Hold down the SET button for a little longer than 3 seconds 2 With the 4 or button select FAV CH and confirm with the OK button In the LCD display appears SETUP 3 With 4 or button select DEL ALL and confirm with the OK button In the LCD display appears SURE DELET are you sure 4 With the OK button O you confirm the deletion of all programmed favourites channels After which DELETED appears in the LCD display 69 followed by SETUP 5 To exit this menu press repeatedly the EXIT button until the standard display appears in the LCD display Tips When the LCD display shows SURE DELET you can stop the delete with the EXIT button 2 Press any device button to exit the favourites de
26. ons Q Access the electronic programme guide Arrow buttons EXIT button Q INFO button Q OK button MENU button SWAP button PIP button MACRO button 6 X Mute switching FAV CH button AV button Infrared Sender Receiver Battery compartment cover Note The functions described here pertain to the theoretically ideal circumstance that the button structure of the respective original remote control is identical to this universal remote control This only occurs however in rare cases If there fore not all of the original remote control s functions can be reproduced it is not due to a dificiency in the Universal remote control All the brand names used in these instructions or in the accompanying code list are trademarks of the corre sponding companies First use Unpacking the device checking the package contents A Attention Keep the plastic packaging well away from small children There is a risk of suffocation Unpack the device and accessories Check the package contents Universal remote control Operating instructions Manvfacturer list with device code list Remove the protective foil from the LCD display D Note Transport damage If you notice any transport damage contact the manufacturer or the manufacturer s Service Hotline see warranty card Inserting the batteries Attention The Universal remote control must only be operate
27. press the button for the device O i e TV to which the command should be sent 5 In the LCD display appears SUCCESS The setting is saved In the event of an error ERROR appears in the LCD display After which VPT SETUP appears again 6 With the EXIT button you exit this mode Back to volume control If you want to return to the basic volume control proceed as follows 1 Press the desired device button except PC 2 Hold down the SET button for a little longer than 3 seconds 3 With the or button select BASIC VPT and confirm with the OK button 9 22 4 In the LCD display appears SUCCESS 5 With the EXIT button you exit the mode Additional functions gt To operate one of the programmed devices with the URC first press the corresponding device button c Then point the URC to this device and press the desired button gt Put the number buttons exactly as you do with the original remote control Before you make a two digit entry press the button 0 c With the Reca button 69 you can select the respectively last selected programme memory slot c Press the GUIDE button to start the electronic pro gramme guide of a device equipped with this function lt gt Press the INFO button to show current programme information from the target device c Via the MENU button you access the dialogue for the setting of the respective target device All OFF Qo
28. ro deletion To delete a preprogrammed Macro proceed as follows 1 Hold down the SET button for a little longer than 3 seconds 2 With the 4 button select MACRO and confirm with the OK button 3 With the 4 or gt button select the desired Macro and confirm with the OK button In the LCD display ap pears SET UP 4 With the 4 or button select DELETE and confirm with the OK button 5 In the LCD display 0 appears SURE DELET are you sure Confirm the delete process with the OK button In the LCD display 69 is shown the memory slot of the Macro that has just been deleted 6 With 4 or button you can delete other Macros Then continue with step 3 19 7 With the EXIT button you will move one level upwards in the menu Favourites channel D Note This function is only available in the TV SAT and CABLE modes and can not be used with other devices it is also supported AUX mode if TV SAT or CABLE is programmed here With this function you can only show the stations which you have summarized in favourite channels Each of the 15 favourites channels be assigned 6 stations i e in channel only sports stations in the next all the news stations etc When the child protection is activated the favourites of the device in question can not be retrieved Favourites programming overview FAV CH lex SETUP ek SELECT KEY
29. rther Macros 9 With the EXIT button you will move one level upwards in the menu 18 A maximum of 16 button commands saved a Macro After entering the 16 button commands the Macro is automatically saved and in the LCD display appears SUCCESS 2 To exit the mode without saving press the EXIT button 3 You can not save any Macros on a slot that is already occupied If you want to programme a new Macro you must first delete the old Macro 4 In the SELECT KEY mode you can only return to the previous status with the EXIT button Example You want to save a command chain in a Macro We begin in the SELECT KEY mode Desired command chain Switch on TV gt switch to DVD gt switch on DVD and playback In the SELECT KEY mode for this you enter the following button commands TV gt gt gt DVD CD gt gt gt Execute a Macro To execute a preprogrammed Macro proceed as follows 1 Press the MACRO button 2 With the corresponding number button O access the desired Macro 1 6 Example If Macro 3 is to be executed first press the Macro button and then the number button 3 Note If no Macro number button is pressed within 18 seconds or a Macro number button is pressed for which no Macro has been programmed or another button is pressed then no Macro can be executed In this case the background illumination blinks 4 times in rapid succession Mac
30. skin rinse with large amounts of water If the liquid comes into con tact with your eyes rinse thoroughly with water do not rub and immediately consult a doctor Always change all batteries at the same time and always use batteries of the same type Keep batteries well away from children Children can put batteries into their mouths and swallow them If a battery is swallowed medical assistance must be sought immedi ately A Laser The universal remote control has an infrared diode of laser class 1 safety system prevents the emission of hazardous laser radiation during use To prevent eye injuries do not modify or damage the safety system of the device Damage to the device If the device is defective do not attempt to repair it your self In case of damage contact the manufacturer or the manufacturer s service hotline see Warranty card If liquid escapes from the device or if the device has been otherwise damaged it must be inspected by the manufacturer or the manufacturer s service hotline Contact the manufacturer or the manufacturer s service hotline see Warranty card Device overview LCD display ALL OFF button SET button Device buttons Illumination button Q CH buttons Q VOL buttons O Teletext On Off O Number buttons RECALL button Button for one or two digit programme numbers Playback button and teletext button Fast text butt
31. the or button select DELETE DEV delete device and confirm with the OK button In the LCD display 69 appears SELECT DEV select device 4 Select the device button O for the device whose taught button command you want to delete 5 In the LCD display appears SURE DELET Confirm with the OK button In the LCD display appears DELETED and then SELECT DEV 6 Repeat steps 4 5 if you also want to delete taught button commands of other devices 7 The EXIT button returns you to the previous status Note The delete process can take several minutes depending on the number of taught commands Delete All programmed buttons 1 Hold down the SET button for a little longer than 3 seconds 2 With the 4 or button select LEARNING and con firm with the OK button In the LCD display appears LEARN KEY 3 With the 4 or gt button select DELETE ALL and con firm with the OK button 4 In the LCD display appears SURE DELET Confirm with the OK button In the LCD display appears DELETED and then again DELETE ALL 5 With the EXIT button you return to the previous status 17 Note The delete process can take a few minutes Please be patient Programming Macros With the MACRO function up to 16 button commands can be carried out with the press of a single button that is to say several previously saved control commands can be deleted with one MACRO
32. your normal domestic waste This product is subject to the European directive 2002 96 EC Universal remote control Have the universal remote control or parts of it disposed of by a professional disposal company or by your com munal disposal facility Observe the currently applicable regulations In case of doubt contact your disposal facility 26 Batteries rechargeable batteries Used batteries rechargeable batteries may not be disposed of in household waste Batteries can contain poisons which are damaging to the environment Therefore dispose of the batteries rechargeable batteries in accordance with statutory regulations Every consumer is legally obliged to surrender batteries rechargeable batteries to a community collection centre in their district or to a dealer The purpose of this obligation is to ensure that batteries are disposed of in a non polluting manner Only dispose of batteries when they are fully discharged Dispose of packaging materials in an environmentally 59 responsible manner CE Conformity This device has been tested approved regarding con formance with the fundamental requirements and other relevent regulations of the EMV Directive 2004 108 EC Importer KOMPERNASS GMBH BURGSTRASSE 21 44867 BOCHUM GERMANY www kompernass com Technical data Controllable devices 8 Dimensions LxWxH 225 56 28 mm Weight 120 g without batteries
Download Pdf Manuals
Related Search