Home

Sanyo PLV-60 Projector User Manual

1. NOTE When On start function is ON this projector is turned on automatically by switching MAIN ON OFF SWITCH Preparation Display disappears after 30 seconds on Refer to page 37 3 Press POWER ON OFF button on Top Control or on Remote Control Unit to ON LAMP Indicator dims and Cooling Fans start to operate Preparation Display appears on a screen and the count down starts The signal from the PC or Video source appears after 30 seconds TURNING OFF THE PROJECTOR 1 Press POWER ON OFF button on Top Control or on Remote Control Unit and the message Power off appears on a Screen 2 Press POWER ON OFF button again to turn off projector LAMP Indicator lights bright and READY Indicator turns off After projector is turned off Cooling Fans operate for 90 seconds During this Cooling Down period this appliance cannot be Power off turned on Message disappears after 4 seconds 3 When projector has cooled down READY Indicator turns to green again and you can turn projector on After cooling down completely turn MAIN ON OFF SWITCH to OFF and disconnect AC Power Cord TURN PROJECTOR ON WAIT AT LEAST 5 TO MAINTAIN THE LIFE OF LAMP ONCE YOU MINUTES BEFORE TURNING IT OFF When Power Management function is ON projector detects signal interruption and turns off Projection Lamp automatically Refer to Power Management on page 37 When WARNING TEMP Indicator
2. PC ADJUST MENU IMAGE ADJUST MENU SCREEN MENU Used to adjust Used to adjust Used to adjust parameters to computer image size of image match with input Contrast Brightness Refer to P30 signal format White Balance R G B Refer to P24 26 Gamma Refer to P29 eam eee Press MENU BUTTON for VIDEO input source INPUT MENU Used to select input IMAGE SELECT MENU Used to select image SCREEN MENU Used to set size of source among INPUT 1 level among image to Full 2 or 3 and to select Standard Cinema or Zoom Normal or video source Image 1 4 Wide zoom Refer to P31 Refer to P33 Refer to P35 SYSTEM MENU IMAGE ADJUST MENU Used to select Used to adjust picture image system of selected Contrast Brightness Color video source Tint White balance Sharpness Refer to P32 Gamma Noise Reduction Progressive Refer to P34 Same function as the Computer Mode Same function as the Computer Mode 19 BASIC OPERATION 20 TURNING ON OFF PROJECTOR TURNING ON PROJECTOR 1 Complete the peripheral connections with Computer VCR etc before turning on projector Refer to CONNECTING TO PROJECTOR on Pages 11 13 for connecting that equipment 2 Connect the projector s AC Power Cord into an AC outlet and 30 turn MAIN ON OFF SWITCH to ON LAMP Indicator lights RED and READY Indicator lights GREEN
3. RARE Image Level Menu Move a red frame pointer to any of Image 1 to 4 where you want to set and then press SELECT button Reset all adjustment to previous figure Closes IMAGE MENU 0 Bar S iv E p Other icons operates as follows 29 COMPUTER MODE 30 PICTURE SCREEN ADJUSTMENT This projector has a picture screen resize function which enables you to display the desirable image size 1 Press MENU button and ON SCREEN MENU will appear Press POINT LEFT RIGHT button s to move a red frame pointer to SCREEN Menu icon 2 Press POINT DOWN button and move a red frame pointer to the function that you want to select and then press SELECT button Em Provides image to fit the vertical size of the screen Provides image to fit the horizontal size of the screen Provides image in its original size When the original image size is larger than screen size 1366 x 768 this projector enters Digital Zoom mode automatically Image size can be set to Normal by pressing NORMAL button Adjusts image size or pans image In Digital Zoom mode the ON SCREEN MENU disappears and the magnifying glass icon and the message D Zoom is displayed This projector also enters Digital Zoom mode by pressing the D ZOOM A Y button on Remote Control Unit Refer to the following for operation Expand function To expand the image size press the D ZOOM A button or the SELECT button The
4. Multimedia Projector PLV 60 Owner s Manual Before operating this projector read this manual thoroughly and operate the projector properly This projector provides many convenient features and functions Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time Improper operation may result in not only shortening the product life but also malfunctions fire hazard or other accidents If your projector seems to operate improperly read this manual again check operations and cable connections and try the solutions in the Trouble shooting section of the end of this booklet If the problem still persists contact the sales dealer where you purchased the projector or the service center A SAFETY PRECAUTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE This projector produces intense light from the projection lens Do not stare directly into the lens as possible Eye damage could result Be especially careful that children do not stare directly into the beam This projector should be set in the way indicated If not it may result in a fire hazard Take appropriate space on the top sides and rear of the projector SIDE and TOP REAR cabinet for allowing air circulation and cooling the projector son Minimum distance should be taken If the projector i
5. Press LENS SHIFT A button or POINT UP button to move image up and press LENS SHIFT button or POINT DOWN button to move image down Refer to P9 for operating range Lens shift Message disappears after 4 seconds KEYSTONE ADJUSTMENT Press KEYSTONE button on Remote Control Unit or select Keystone on SETTING Menu P36 The message Keystone is displayed Correct keystone distortion by pressing POINT UP DOWN button s Press POINT UP button to reduce upper part of the image and press POINT DOWN button to reduce lower part of the image To reset Keystone adjustment press NORMAL button Reduce the upper width with POINT UP button Reduce the lower width with POINT DOWN button 4 Keystone Message disappears after 4 seconds 21 BASIC OPERATION 22 NO SHOW FUNCTION Press NO SHOW button on Remote Control Unit to black out the image To restore to normal press NO SHOW button again or press any other button No show Message disappears after 4 seconds PICTURE FREEZE FUNCTION Press FREEZE button on Remote Control Unit to freeze the picture on screen To cancel FREEZE function press FREEZE button again or press any other button SOUND ADJUSTMENT VOLUME ADJUSTMENT Press VOLUME button s Top Control or on Remote Control Unit to adjust volume Volume dialog box appears on the screen for a few seconds but
6. Unit together for over 10 seconds After changing the code make sure the Remote Control operates properly To return to the normal code Code 1 operate both projector and Remote Control in the ways above again NOTE When batteries of the Remote Control Unit is replaced the remote transmit code automatically returns to the normal code Code 1 Sil Lamp counter reset This function is used to reset Lamp Replace Counter When replacing Projection Lamp reset Lamp Replace Counter by using this function Refer to page 39 for operation SETTING Time left p m off Auto 25 EO i E fm e Move the pointer to the item and then press POINT LEFT RIGHT button s PS isi EE EO i Eo fd E Lamp replace counter Reset Yes No Move the pointer to Lamp counter reset and then press SELECT button The message Lamp replace counter reset is displayed 37 APPENDIX MAINTENANCE WARNING TEMP INDICATOR WARNING TEMP Indicator flashes red when internal temperature of projector exceeds normal temperature The Indicator stops flashing when temperature of projector returns to normal When WARNING TEMP Indicator continues to flash check 38 the items listed below 1 Ventilation slots of projector may be blocked In such an event reposition the appliance so that Ventilation slots are not obstructed 2 Air Filters may be
7. When this mark is displayed as black more computer system modes will be available Move the arrow to this mark and then press SELECT button and the other modes will be displayed PC ADJUSTMENT AUTO PC ADJUSTMENT Auto PC Adjustment function is provided to automatically adjust Fine sync Total dots and Picture Position to conform to your computer Auto PC Adjustment function can be operated as follows Ea Auto Adi 1 Press MENU button ON SCREEN MENU will appear Press PC ADJUST MENU POINT LEFT RIGHT button to move a red frame pointer to PC ADJUST Menu icon Fi fay ol lt 2 Press POINT DOWN button to move a red frame pointer to AUTO PC Adj icon and then press SELECT button This Auto PC Adjustment can be executed by pressing AUTO PC ADJ button on Top Control or on Remote Control Unit i PC ADJUST Menu icon feed Move red frame pointer to AUTO Fine sync Total dots and Picture Position of some computers Adjsicon press SELES UNO rs may not be fully adjusted with Auto PC Adjustment function When the image is not provided properly through this function manual adjustment is required Refer to page 25 26 v Store adjustment parameters Adjustment parameters from Auto PC Adjustment can be memorized in this projector Once parameters are memorized setting can be done just by selecting Mode in SYSTEM Menu above Refer to step 3 of MANUAL PC ADJUSTMENT section P26 NOTE
8. Auto PC Adjustment function cannot be operated when RGB HDTV720p HDTV1035i or HDTV1080i is selected on SYSTEM Menu 23 24 COMPUTER MODE MANUAL PC ADJUSTMENT This projector can automatically tune to the display signals from most personal computers currently distributed However some computers employ special signal formats which are different from the standard ones and may not be tuned by Multi Scan system of this projector If this happens projector cannot reproduce a proper image and the image may be recognized as a flickering picture a non synchronized picture a non centered picture or a skewed picture This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special signal formats This projector has 5 independent memory areas to memorize those parameters manually adjusted This enables you to recall the setting for a specific computer whenever you use it Note This PC ADJUST Menu cannot be operated when RGB is selected on SYSTEM Menu P23 24 1 Press MENU button and ON SCREEN MENU will appear Press POINT LEFT RIGHT button to move a red frame pointer to PC ADJUST Menu icon 2 Press POINT DOWN button to move a red frame pointer to the item that you want to adjust and then press SELECT button Adjustment dialog box will appear Press POINT LEFT RIGHT button to adjust the value EH Adjust the picture as necessary to eliminate flicker from the dis
9. BASIC OPERATION TURNING ON OFF PROJECTOR ADJUSTING SCREEN ZOOM ADJUSTMENT FOCUS ADJUSTMENT LENS SHIFT ADJUSTMENT KEYSTONE ADJUSTMENT NO SHOW FUNCTION PICTURE FREEZE FUNCTION SOUND ADJUSTMENT VOLUME ADJUSTMENT MUTE SETTING TRADEMARKS Apple Macintosh and PowerBook are trademarks or registered trademarks of Apple Computer Inc o eon oo 11 11 13 COMPUTER MODE SELECTING INPUT SOURCE SELECTING COMPUTER SYSTEM PC ADJUSTMENT AUTO PC ADJUSTMENT MANUAL PC ADJUSTMENT COMPATIBLE COMPUTER SPECIFICATIONS PICTURE IMAGE ADJUSTMENT IMAGE LEVEL SELECT IMAGE LEVEL ADJUSTMENT PICTURE SCREEN ADJUSTMENT VIDEO MODE SELECTING INPUT SOURCE SELECTING VIDEO SYSTEM PICTURE IMAGE ADJUSTMENT IMAGE LEVEL SELECT IMAGE LEVEL ADJUSTMENT PICTURE SCREEN ADJUSTMENT SETTING SETTING MENU APPENDIX MAINTENANCE WARNING TEMP INDICATOR AIR FILTER CARE AND CLEANING CLEANING THE PROJECTION LENS LAMP REPLACEMENT LAMP REPLACE COUNTER TROUBLESHOOTING TECHNICAL SPECIFICATIONS and PS 2 are trademarks or registered trademarks of International Business Machines Inc Windows and PowerPoint are registered trademarks of Microsoft Corporation Each name of corporations or products in the owner s manual is a trademark or a registered trademark of its respective corporation TABLE OF CONTENTS FEATURES AND DESIGN This Multimedia Projector is designed with the most advanced technology fo
10. Reset all adjustment to previous figure Closes IMAGE MENU VIDEO MODE Stored Standard e 5 02 Image Level Menu 0 3j Move a red frame pointer to m4 the image icon to be set A and then press SELECT button m PICTURE SCREEN ADJUSTMENT This projector has a picture screen resize function which enables you to display the desirable image size 1 Press MENU button and ON SCREEN MENU will appear Press POINT LEFT RIGHT button s to move a red frame pointer to SCREEN Menu icon 2 Press POINT DOWN button and move a red frame pointer to the function that you want to select and then press SELECT button Provides image to fit width of screen by expanding image width uniformly This function can be used for providing a squeezed video signal at wide video aspect ratio of 16 9 When your video equipment such as DVD has 16 9 output mode select 16 9 and select Full on this SCREEN Menu to provide better quality S zoom Provides image to fit screen size 16 9 aspect ratio by expanding image width and height uniformly This function can be used for providing a letter box mode picture 4 3 aspect picture with black bar on top and bottom edges at wide video aspect of 16 9 Provides image at the normal video aspect ratio of 4 3 Wide zoom Provides image to fit width of screen by expanding both sides of image
11. This function is suitable to provide a normal video signal 4 3 aspect ratio at wide video aspect ratio of 16 9 SCREEN MENU a a SCREEN Menu icon Move the red frame to the function and press SELECT button NOTE SCREEN Menu cannot be operated when 720p 1035i 1080i 50 or 10801 60 is selected on SYSTEM Menu P32 35 SETTING SETTING MENU 36 1 Press MENU button and ON SCREEN MENU will appear Press POINT LEFT RIGHT button s to move a red frame pointer to SETTING icon 2 Press POINT DOWN button to move a red frame pointer to the item that you want to set and then press SELECT button Setting dialog box appears nm Language Language used in ON SCREEN MENU is selectable from among English German French Italian Spanish Portuguese Dutch Swedish and Japanese zm When the image is distorted vertically select Keystone ON SCREEN Menu disappears and the message Keystone is displayed Correct the Keystone distortion by pressing the POINT UP DOWN button s Refer to KEYSTONE ADJUSTMENT on page 21 ci Emp When this function is On this projector will produce a blue image instead of the video noise on the screen when the input source is unplugged or turned off This function decides whether to display the On Screen Displays On shows all the On Screen Displays Off sets the On Screen Displays disappeared except ON SCREEN MENU Power off
12. White balance Blue Press POINT LEFT button to lighten blue tone and POINT RIGHT button to deeper tone From 0 to 63 Press POINT LEFT button to soften the image and POINT RIGHT button to sharpen the image From 0 to 31 Z Press either POINT LEFT button or POINT RIGHT button to obtain better balance of contrast From 0 to 15 Noise reduction Set On to reduce noise rough parts of the image Progressive Set On to provide progressive scan mode NOTE Tint cannot be adjusted when the video system is PAL SECAM PAL M or PAL N Noise reduction cannot be selected when the input signal is from Y Pb Cb Pr Cr jacks Progressive cannot be selected when 480p 575p or 720p is selected on SYSTEM Menu P32 IMAGE ADJUST MENU D IMAGE ADJUST Menu icon Move a red frame pointer to the item to be selected and then press SELECT button OO qi Standard Press POINT LEFT RIGHT buttons to adjust value Press SELECT button at this icon to display other items uo do o Press POINT LEFT RIGHT buttons to adjust value Press SELECT button at this icon to store the value 3 To store the adjustment data move a red frame pointer to Stored icon and press SELECT button Image Level Menu will appear Move a red frame pointer to the Image Level 1 to 4 and then press SELECT button Other icons operates as follows
13. flashes red projector is automatically turned off Wait at least 5 minutes before turning on projector again When WARNING TEMP Indicator continues to flash follow procedures below 1 Turn MAIN ON OFF SWITCH to OFF and disconnect the AC Power Cord from a AC outlet 2 Check Air Filters for dust accumulation 3 Clean Air Filters See AIR FILTER CARE AND CLEANING section on page 38 4 Turn projector on again If WARNING TEMP Indicator should still continue to flash contact the sales dealer where you purchased this projector or Service center ADJUSTING SCREEN bo M If image has keystone distortion correct image with KEYSTONE adjustment 1 2 BASIC OPERATION ZOOM ADJUSTMENT Press ZOOM A Y button s on Top Control or on Remote Control Unit The message Zoom is displayed Press ZOOM A button or POINT UP button to make image larger and press ZOOM V button or POINT DOWN button to make image smaller Zoom Message disappears after 4 seconds FOCUS ADJUSTMENT Press FOCUS button s on Top Control or on Remote Control Unit The message Focus is displayed Adjust focus of the image by pressing FOCUS A YW button s or POINT UP DOWN button s Focus Message disappears after 4 seconds LENS SHIFT ADJUSTMENT Press LENS SHIFT button s on Top Control or LENS SHIFT button on Remote Control Unit The message Lens shift is displayed
14. image is magnified by degrees Compress function To compress the image size press the D ZOOM button The size of image is reduced by degrees Panning function To pan the image press the POINT UP DOWN LEFT RIGHT buttons Panning function can work only when the image is larger than the screen size To return to screen size previously set press NORMAL button To cancel Digital Zoom mode press any button except D ZOOM A Y SELECT POINT NORMAL or AUTO PC ADJ button SCREEN MENU SCREEN Menu icon Move the red frame to the function and press SELECT button NOTE This SCREEN Menu cannot be operated when HDTV720p HDTV1035i or HDTV1080i is selected on SYSTEM Menu P23 24 True and Digital Zoom cannot be selected when RGB is selected on SYSTEM Menu P23 24 This projector cannot display any resolution higher than 1280 X 1024 If your computer s screen resolution is higher than 1280 X 1024 reset the resolution to the lower before connecting projector The image data in other than XGA 1024 x 768 is modified to fit the screen size in the initial mode Panning function may not operate properly if the computer system prepared on PC ADJUST Menu is used VIDEO MODE SELECTING INPUT SOURCE DIRECT OPERATION INPUT button Choose either Input 2 or Input 3 by pressing INPUT button on the Top Control or on the Remote Control Unit Inp
15. message 1 KE When this function is On projector displays logo when starting up EET When this function is On picture is top bottom and the left right reversed This function is used to project the image from a ceiling mounted projector eb4 When this function is On picture is left right reversed This function is used to project the image to a rear projection screen SETTING MENU NETCHEN Set the red frame SETTING Menu icon pointer to the item and press SELECT button When selecting Language Language Menu appears On Kb On Kb ox KO 694 SI KO orr KO 100 ie E Ge a Portugu s Nederlands BAGS Move the pointer to the item and then press POINT LEFT RIGHT button s Ceiling function 9 Power management This function turns Projection Lamp off when projector detects signal interruption and projector is not used for a certain period in order to reduce power consumption and maintain the Lamp life This projector is shipped with this function ON Power Management function operates to turn Projection Lamp off when the input signal is interrupted and projector is not operated over 5 minutes This function operates as follows 1 When the signal is interrupted No signal and the counting down display a
16. poor image quality When using under dusty or smoky conditions dust may accumulate on the liquid crystal panel Projection Lens or optical elements inside it This condition may degrade the quality of the projected image When the above symptoms are noticed contact your authorized dealer or service station for proper cleaning Air Filter Cover m Press the latches My sideways and pull up Air Filters Remove three Air Filters by pulling up the latches CLEANING THE PROJECTION LENS Follow these steps to clean the projection lens 1 Apply a non abrasive camera lens cleaner to a soft dry cleaning cloth Avoid using an excessive amount of cleaner Abrasive cleaners solvents or other harsh chemicals might scratch the lens 2 Lightly wipe the cleaning cloth over the lens 3 When projector is not in use replace the lens cover APPENDIX LAMP REPLACEMENT When the life of the Lamp of this projector draws to an end the LAMP REPLACEMENT Indicator lights yellow When the image becomes dark or the color of the image becomes unnatural replacement of the Lamp is required CAUTION AN For continued safety replace with a lamp assembly of the same type Allow projector to cool for at least 45 minutes before you open the lamp cover The inside of projector can become very hot Do not drop the lamp assembly or touch the glass bulb The glass can shatter and may cause injury Follow these steps to replace
17. projector automatically tunes to incoming signal and projects proper image without any special setting Some computers need setting manually Note Projector may display one of the following messages AUTO PC Adj When projector cannot recognize connected signal SYSTEM MENU as PC system provided in this projector Auto PC SYSTEM el Adjustment function operates to adjust projector and the message AUTO PC Adj is displayed on SYSTEM icon When image is not provided SYSTEM Menu icon 2 properly manual adjustment is required Refer to Displays system being P25 and 26 selected There is no signal input from computer Make sure the connection of computer and projector is Set correctly Refer to TROUBLESHOOTING on page 40 XGA 1 Modet 23 COMPUTER MODE 24 SELECT COMPUTER SYSTEM MANUALLY This projector automatically selects PC system among those provided SYSTEM MENU in this projector and PC system can be also selected manually _ Press MENU button and ON SCREEN MENU will appear Press SYSTEM e Modet F a oO POINT LEFT RIGHT buttons to move a red frame pointer to SYSTEM icon yt SYSTEM Menu icon Displays system being selected 2 Press POINT DOWN button to move a red arrow pointer to the Th his dial System that you want to set and then press SELECT button S systems ORIS box can be selected Custom Mode 1 5 set in PC ADJUST Menu P25 26
18. 14 F 140 F 10 60 C Remote Control Transmitter Power Source Operating Range Dimensions Net Weight AA UMG or R06 Type x 2 16 4 5m 30 1 8 x 0 75 x 6 7 45mm 19mm x 170mm 0 20 Ibs 92 g including batteries Accessories Owner s Manual AC Power Cord Wired Wireless Remote Control Transmitter and Batteries Video Cable RCA x 1 Audio Cable RCA x 2 S Video Cable Remote Control Cable Dust Cover Lens Cover The specifications are subject to change without notice APPENDIX CONFIGURATIONS OF TERMINALS RGB TERMINAL Terminal HDB15 PIN Connect the display output terminal of computer to this terminal with VGA Cable not supplied When connecting the Macintosh computer the MAC Adapter not supplied is required Pin Configuration 1 Red Input 9 No Connect 2 Green Input 10 Ground Vert sync ON NONO 3 Blue Input 11 Sense 0 4 Sense 2 12 Sense 1 o O6 90 5 Ground Horiz sync 13 Horiz sync 6 Ground Red 14 Vert sync 7 Ground Green 15 Reserved 8 Ground Blue SERIAL TERMINAL Terminal HDB9 PIN Connect the serial port of computer to this terminal with Serial Cable not supplied Pin Configuration 1 No Connect 6 No Connect 2 RxD 7 RTS 3 TxD 8 CTS 4 No Connect 9 No Connect 5 Ground MAC AD
19. 5 difterlaco XGA 10 1024 768 62 04 77 07 NOTE Specifications are subject to change without notice 27 COMPUTER MODE PICTURE IMAGE ADJUSTMENTS IMAGE LEVEL SELECT DIRECT Select image level among Standard Real Image 1 Image 2 Image 3 IMAGE button and Image 4 by pressing IMAGE button on the Remote Control Unit Standard Standard Normal picture level preset on this projector This normal picture level can also be selected by pressing NORMAL button Picture level adjusted for the picture with fine tone IMAGE 1 4 User preset picture adjustment in IMAGE ADJUST Menu P29 IMAGE LEVEL SELECT MENU 1 Press MENU button and ON SCREEN MENU will appear Press IMAGE SELECT MENU POINT LEFT RIGHT button to move a red frame pointer to IMAGE SELECT Menu icon Image 3 inn 2 Press POINT DOWN button to move a red frame pointer to the level that you want to set and then press SELECT button gt gt Normal picture level preset on this projector Picture level adjusted for the picture with fine tone User preset picture adjustment in IMAGE ADJUST Menu P29 IMAGE SELECT Menu icon Move the red frame icon to the level and press SELECT button The level being selected 28 COMPUTER MODE IMAGE LEVEL ADJUSTMENT 1 Press MENU button and ON SCREEN MENU will appear Press IMAGE ADJUST MENU POINT LEFT RIGHT buttons to move a red frame pointer to IMAG
20. 6 x 768 x 3 panels Color System PAL SECAM NTSC NTSC4 43 PAL M and PAL N High Definition TV Signal 480i 480p 575i 575p 720p 1035i 1080i 50 and 1080i 60 Scanning Frequency H sync 15 100 KHz V sync 50 100 Hz Projection Image size Diagonal Adjustable from 31 to 400 Horizontal Resolution 800 TV lines Projection Lens F 1 8 2 1 lens with f 48 4 mm 62 8 mm with motor zoom focus and shift Throw Distance 4 43 45 9 1 35 m 14 0 m Projection Lamp 250W Computer AV Input Jacks INPUT 1 HDB 15 pin Type Terminal INPUT 2 BNC Type Jacks Video Y C Pb Cb Pr Cr G B R H V Mini DIN 4 pin Type Jack S Video INPUT 3 RCA Type Jacks Video Y Pb Cb Pr Cr Audio Input Jacks Input 1 2 3 RCA Type Jacks R and L mono x 3 Serial Port Terminal HDB 9 pin Type Terminal R C Jack Mini Jack Audio Output Jacks RCA Type Jacks R and L External Speaker Jack 35 mm Mini Jack 8 Q 2 W stereo Internal Audio Amp 2 0 W RMS stereo Built in Speakers 2 speakers 1 57 x 2 76 A0mm x 70mm Feet Adjustment 0 to 9 0 Voltage and Power Consumption AC 100 120 V 4 4 A Max Ampere 50 60 Hz The U S A and Canada AC 200 240 V 2 2 A Max 50 60 Hz Continental Europe and The U K Operating Temperature 41 F 95 F 5 C 35 C Storage Temperature
21. APTER NOT SUPPLIED Set Slide Switches as shown in the table below depending on RESOLUTION MODE that you want to use before you turn on projector and computer Slide Switches 1 6 13 MODE 640 x 480 16 MODE 832 x 624 OFF 19 MODE 1024 x 768 21 MODE 1152 870 SANYO Part No 610 289 4110 1AA6P1P2612 SANYO Electric Co Ltd
22. E ADJUST Menu icon Ex aet 2 Press POINT DOWN button to move a red frame pointer to the item that you want to adjust and then press SELECT button H The level of each item is displayed Adjust each level by ove a red frame pointer to pressing POINT LEFT RIGHT button s he item to be selected and contrast Press POINT LEFT button to decrease contrast and POINT RIGHT button to increase contrast From 0 to 63 Ex Brightness Press POINT LEFT button to adjust image darker and POINT RIGHT button to adjust brighter From 0 to 63 gt White balance Red Press POINT LEFT button to lighten red tone and POINT RIGHT button to deeper tone From 0 to 63 a White balance Green Press POINT LEFT button to lighten green tone and POINT RIGHT button to deeper tone From 0 to 63 White balance Blue Press POINT LEFT button to lighten blue tone and POINT RIGHT button to deeper tone From 0 to 63 Press either POINT LEFT button or POINT RIGHT button to obtain better balance of contrast From 0 to 15 L 3 To store manually preset image move a red frame pointer to STORE icon and press SELECT button Image Level Menu will appear Move a red frame pointer to the Image 1 to 4 where you want to set and then press SELECT button Selected Image level Press POINT LEFT RIGHT buttons to adjust value Stored icon Press SELECT button at this icon to store the adjustment 2m ANd ea
23. G PROJECTOR CONNECTING TO VIDEO EQUIPMENT Cables used for connection Cables are not supplied with this projector Video Cable RCA x 1 NOTE Video Cable RCA x 3 BNC x 1 BNC x 2 BNC x 3 When connecting projector AC Power Cords of S VIDEO Cable both projector and external equipment should be Audio Cable RCA x 2 disconnected from AC outlet Speaker Cable Mini x 1 stereo Video Source example Component video output equipment such as DVD player or Video Cassette Recorder Video Disc Player high definition TV source a Component Video Composite Separate Component Video S VIDEO Audio Output Output Video Output Video Output Output Output Video Cable Video Video Video Cable Video Cable S VIDEO Audio Cable RCA x 3 s Cable Cable BNC x 2 BNC x 3 s Cable RCA x 2 RCA x 1 BNC x 1 x Y Pb Cb Pr Cr VIDEO VIDEO Y C Y Pb Cb Pr Cr S VIDEO R L INPUT 1 R C JACK AUDIO OUT EXT SP 80 R AUDIO L 9 6 M Speaker Cable Audio Cable Mini stereo RCA x 2 Speaker 80 2W Audio Amplifier External Audio Equipment Audio Speaker stereo Audio Amplifier 12 CONNECTING PROJECTOR CONNECTING TO COMPUTER Cables used for connection Cables are not supplied with this projector e VGA Cable HDB 15 pin s NOTE Video Cable BNC x 5 When conne
24. INDICATORS on its top TOP CONTROLS AND INDICATORS INDICATORS LAMP REPLACE INDICATOR WARNING TEMP INDICATOR READY INDICATOR LAMP INDICATOR This indicator turns to This indicator flashes This indicator lights green This indicator is dim when yellow when the life of when internal projector when projector is ready to projector is turned on And Projection Lamp draws to temperature is too high be turned on And it bright when projector is in an end P39 P38 flashes green in Power stand by mode Management mode P37 LAMP LAMP REPLACE WARNING READY TEMP 14 BEFORE OPERATION TOP CONTROL FOCUS BUTTONS MENU BUTTON POWER ON OFF BUTTON INPUT BUTTON Used to adjust focus Used to adjust zoom AUTO PC ADJ BUTTON Adjustment function ZOOM BUTTONS as ON are P21 Used to select MENU Used to turn projector on Used to select input source operation P18 19 or off P20 among INPUT 1 2 or 3 P23 31 VOLUME BUTTONS Used to adjust volume P22 O INPUT ZOOM FOCUS LENS SHIFT VOLUMF P AEN NORMAL e LENS SHIFT BUTTONS Used to adjust lens shift P21 DJ POINT BUTTONS NORMAL BUTTON Used to operate Auto Used to move Pointer or to Used to execute the item Used to reset to normal P24 adjust the item on On Screen selected or to expand picture adjustments preset MENU itis also usedto image in Digital Zoom
25. NU 1 Press MENU button to display ON SCREEN MENU MENU BAR A red frame is POINTER Select item to be adjusted Move POINTER red frame to MENU ICON that you want to select by pressing POINT RIGHT LEFT buttons Control and adjust through ON SCREEN MENU Press POINT DOWN button and move POINTER red frame or red arrow to ITEM that you want to adjust and then press SELECT button to show Item Data Adjust ITEM DATA by pressing POINT buttons Refer to the following pages for details of respective adjustments MENU BAR De POINTER red frame Press POINT DOWN button to move POINTER MENU ICON POINTER red frame ITEM oa oo On On KD On off epg off KO off Xp e Off BI Codet SE y 2 Press POINT LEFT RIGHT buttons to adjust the value m BEFORE OPERATION MENU BAR FOR PC SOURCE Press MENU BUTTON for PC input source INPUT MENU IMAGE SELECT MENU Used to select Used to select image SETTING MENU Used to change settings SYSTEM MENU input source level among of projector and reset among INPUT 1 Used to select Standard Real or Lamp Replace Counter 2 or 3 computer system Image 1 4 Refer to P36 37 Refer to P23 Refer to P23 24 Refer to P28 me Mods MC Lem Shows selected item of ON SCREEN MENU
26. T button 3 Another confirmation dialog box appears and select Yes to reset Lamp Replace Counter Do not reset Lamp Replace Counter except after Projection Lamp is replaced 39 APPENDIX TROUBLESHOOTING Before calling your dealer or service center for assistance check the matters below once again 1 Make sure you have connected projector to your equipment as described in the section ONNECTING THE PROJECTOR on pages 11 13 2 Check cable connection Verify that all computer video and power cords are properly connected 3 Verify that all power is switched on 4 If projector still does not produce an image re start the computer 5 If the image sill does not appear unplug projector from the computer and check the computer monitor s display The problem may be with your graphics controller rather than with projector When you reconnect projector remember to turn the computer and monitor off before you power up projector Power the equipment back on in order of projector and computer 6 If the problem still exists check the following chart Problem Try these Solutions No power Plug projector into the AC outlet Be sure READY Indicator light is On Wait 90 seconds after projector is turned OFF before turning projector back on NOTE After pressing the power ON OFF switch to OFF make sure projector works as follows 1 The LAMP Indicator will light and the READY Indicator will turn off 2 After 90 se
27. WARNING A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET OUTLET The Wires in this mains lead are coloured in accordance with the following code Green and yellow Neutral As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol 1 or coloured green or green and yellow The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red WARNING THIS APPARATUS MUST BE EARTHED THE SOCKET OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE FEATURES AND DESIGN PREPARATION NAME OF EACH PART OF PROJECTOR SETTING UP PROJECTOR CONNECTING AC POWER CORD POSITIONING PROJECTOR ADJUSTABLE FEET MOVING PROJECTOR CONNECTING PROJECTOR TERMINALS OF PROJECTOR CONNECTING TO VIDEO EQUIPMENT CONNECTING TO COMPUTER BEFORE OPERATION TOP CONTROLS AND INDICATORS OPERATION OF REMOTE CONTROL OPERATING RANGE WIRED REMOTE CONTROL OPERATION REMOTE CONTROL BATTERIES INSTALLATION OPERATING ON SCREEN MENU HOW TO OPERATE ON SCREEN MENU FLOW OF ON SCREEN MENU OPERATION MENU BAR
28. XGA5 1280x1024 63 74 60 01 2 800x600 37 88 60 32 SXGA6 1280x1024 71 69 67 19 SVGA3 800x600 46 875 75 00 SXGA7 1280x1024 81 13 76 107 SVGA4 800x600 53674 85 00 5 8 1280x1024 63 98 60 02 SVGA5 800x600 48 08 7219 SXGA9 1280 1024 79 976 75 025 SVGA6 800x600 37 90 61 03 SXGA 10 1280 x 960 60 00 60 00 SVGA7 800x600 34 50 55 38 SXGA 11 1152x900 61 20 65 20 SVGA8 800x600 38 00 60 51 SXGA 12 1152x900 71 40 75 60 SVGA9 800x600 38 60 60 31 SXGA 13 1280x1024 50 00 10 800 600 32 70 5109 SXGA 14 1280x1024 50 00 interea SVGA11 800 600 38 00 60 51 15 1280x1024 63 37 60 01 16 832x624 49 72 74 55 5 6 16 1280x1024 76 97 72 00 1 1024 768 48 36 60 00 17 1152 900 61 85 66 00 XGA 2 1024x768 68 677 84 997 SXGA18 1280x1024 46 43 ee XGA3 1024x768 60 023 75 08 SXGA19 1280x1024 63 79 60 18 XGA4 1024 x 768 56 47 7007 20 1280x1024 91 146 85 024 XGA5 1024x768 60 31 74 92 MAC 1280 x 960 75 00 75 08 XGA6 1024x768 48 50 60 02 MAC 1280 1024 80 00 75 08 XGA7 1024x768 44 00 54 58 HDTV720p 45 00 60 00 XGA 8 1024 x 768 63 48 79 35 10351 33 75 9 1024 768 36 00 1080 33 7
29. ame pointer to the level that you want to set and then press SELECT button Normal picture level preset on this projector Picture level adjusted for the picture with fine tone User preset picture adjustment in IMAGE ADJUST Menu P34 IMAGE SELECT Menu icon Move the red frame pointer to the level and press SELECT button The level being selected 33 VIDEO MODE 34 IMAGE LEVEL ADJUSTMENT 1 Press MENU button and ON SCREEN MENU will appear Press POINT LEFT RIGHT button s to move a red frame pointer to IMAGE ADJUST Menu icon 2 Press POINT DOWN button to move a red frame pointer to the item that you want to adjust and then press SELECT button The level of each item is displayed Adjust each level by pressing POINT LEFT RIGHT button s Press POINT LEFT button to decrease contrast and POINT RIGHT button to increase contrast From 0 to 63 xx Brightness Press POINT LEFT button to adjust image darker and POINT RIGHT button to adjust brighter From 0 to 63 Press POINT LEFT button to lighten color and POINT RIGHT button to deeper color From 0 to 63 Press POINT LEFT button or POINT RIGHT button to obtain proper color From 0 to 63 e White balance Red Press POINT LEFT button to lighten red tone and POINT RIGHT button to deeper tone From 0 to 63 Es White balance Green Press POINT LEFT button to lighten green tone and POINT RIGHT button to deeper tone From 0 to 63 wl
30. automatically set by Auto PC Adjustment No complicated setup is necessary and projection is always precise Progressive Scan for Video Progressive Scan function converts interlace video signals into progressive scan signals and provide fine picture quality Digital Zoom for Computer Digital Zoom function magnifies the image up to 16 times allowing you to focus on crucial information at a presentation Motor driven Lens Shift Projection Lens can be moved up and down with Motor driven Lens Shift function This function makes it easy to provide projected image where you want Zoom and Focus can be also adjusted with Motor driven operation Keystone Correction Positioning height of projector may result in distorted images being displayed in a trapezoid shape Keystone Correction solves this problem by digitally altering projection to produce undistorted images Power Management Power Management function is provided to reduce power consumption while the projector is not in use This Power Management function operates to turn Projection Lamp off when the projector detects signal interruption and any button is not pressed over 5 minutes Projection Lamp is automatically turned on again when the projector detects the signal or any operation button is pressed This projector is shipped with this function ON Multilanguage Menu Display Operation menu is displayed in English German French Italian Spanis
31. ay area dialog box Adjustment of horizontal area displayed with this projector Press POINT LEFT RIGHT button s and adjust number to match the resolution of image Adjustment of vertical area displayed with this projector Press POINT LEFT RIGHT button s and adjust number to match the resolution of image E Horizontal scale Adjustment of width of image Press POINT LEFT RIGHT button s for adjustments Vertical scale Adjustment of height of image Press POINT LEFT RIGHT button s for adjustments NOTE Display area H V Horizontal scale and Vertical scale cannot be adjusted when HDTV1035i or HDTV1080i is selected on SYSTEM Menu P23 24 Fine sync and Total dots cannot be fully adjusted when HDTV1035i or HDTV1080i is selected on SYSTEM Menu P23 24 3 Ek sea To store adjustment parameters move a red frame pointer to Stored icon and then press SELECT button Move a red arrow pointer to any of Mode 1 to 5 that you want to store to and then press SELECT button To clear adjustment parameters previously set move a red frame pointer to Mode free icon and then SELECT button Move a red arrow pointer to the Mode that you want to clear and then press SELECT button Other icons operates as follows Reset all adjust parameters on adjustment dialog box to previous figure Closes PC ADJUST MENU 640x480 5 720x400 800x600 1280x1024 Press SELECT button at Display area icon and
32. be required to correct the interference at his own expense AC POWER CORD REQUIREMENT The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it AC Power Cord for the United States and Canada AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories UL and certified by the Canadian Standard Association CSA AC Power has a grounding type line plug This is a safety feature to be sure that the plug will fit into the power outlet Do not try to defeat this safety feature Should you be unable to insert the plug into the outlet contact your electrician EOS AC Power Cord for the United Kingdom This cord is already fitted with a moulded plug incorporating a fuse the value of which is indicated on the pin face of the plug Should the fuse need to be replaced an ASTA approved BS 1362 fuse must be used of the same rating marked thus If the fuse cover is detachable never use the plug with the cover omitted Ifa replacement fuse cover is required ensure it is of the same colour as that visible on the pin face of the plug i e red or orange Fuse covers are available from the Parts Department indicated in your User Instructions If the plug supplied is not suitable for your socket outlet it should be cut off and destroyed The end of the flexible cord should be suitably prepared and the correct plug fitted See Over
33. by the factory or to reset pan image in Digital Zoom mode P30 screen adjustment in True mode mode Digital Zoom mode or Keystone mode P21 28 30 33 15 BEFORE OPERATION OPERATION OF REMOTE CONTROL 16 Remote Control Unit can be used as either Wired or Wireless WIRED REMOTE JACK When using as Wired Remote Control connect Remote Control Cable to this jack P17 TY EN 0 25 ON OFF Used to mute sound P22 INPUT BUTTON Used to select input source P23 31 POWER ON OFF BUTTON Used to turn projector on or off P20 VOLUME BUTTONS ZOOM mm ZOOM BUTTONS T Used to adjust volume P22 D ZOOM BUTTONS AUTO PC AD D ZOOM FREEZE Used to select Digital Zoom D mode and resize image P30 NO SHOW AUTO PC ADJ BUTTON Use to operate Auto PC Adjustment function P24 IMAGE BUTTON Use to select IMAGE level P28 33 LENS SHIFT BUTTON Used to select LENS SHIFT function P21 Used to select MENU operation P18 19 Used to execute the item selected or to expand image in Digital Zoom mode OPERATING RANGE Used to adjust zoom P21 Cv FOCUS BUTTONS Used to adjust focus P21 FREEZE BUTTON Cv Used to freeze picture P22 KEYSTONE NO SHOW BUTTON Used to turn picture into black image P22 KEYSTONE BUTTON Used dis
34. clogged with dust particles Clean Air Filters by following the section AIR FILTER CARE AND CLEANING below 3 If WARNING TEMP Indicator remains on after performing the above checks Cooling Fans or Internal Circuits may be malfunctioning Contact a service personnel from an authorized dealer or service station AIR FILTER CARE AND CLEANING Removable Air Filter prevents dust from accumulating on the surface of Projection Lens and the Projection Mirror Should Air Filter become clogged with dust particles it will reduce Cooling Fans effectiveness and may result in internal heat build up and adversely affect the life of projector Clean Air Filter following the steps below 1 Turn the power off and disconnect the AC Power Cord from an AC outlet 2 Turn projector upside down and remove Air Filter Cover by pressing four latches sideways and pulling up Remove three Air Filters by pulling up the latches 3 Clean Air Filters with brush or wash out the dust and particles Be sure to dry them out 4 Replace Air Filters and Air Filter Cover properly Make sure that they are fully set CAUTION AN Do not operate projector with Air Filters removed Dust may accumulate on the LCD Panel and the Mirror degrading picture quality Do not put small parts into Air Intake Vents It may result in malfunction of projector RECOMMENDATION We recommend avoiding dusty smoky environments when operating projector Usage in these environments may cause
35. conds the READY Indicator will light green again and projector may be turned on by pressing the power ON OFF button Check WARNING TEMP Indicator If this indicator flashes red projector cannot be turned on See TURNING ON OFF THE PROJECTOR section on page 20 Check the Projection Lamp Refer to page 39 Image is out of e Adjust the focus focus Make sure the projection screen is at least 4 43 1 35 m from projector Check the projection lens to see if it needs cleaning NOTE Moving projector from a cool temperature location to a warm temperature location may result in moisture condensation on the lens In such an event leave projector OFF and wait until condensation disappears Picture is Left Right Check Ceiling Rear feature See SETTING section on page 36 reversed Picture is Check Ceiling feature See SETTING section on page 36 Top Bottom reversed Some displays are 9 Check Display feature See SETTING section on page 36 not seen during the Operation No image Check the connection between the computer or video equipment and projector When turning projector on it takes about 30 seconds to display the image Check the system that you select is corresponding with the computer or the video equipment Make sure the temperature is not out of the Operating Temperature 5 C 35 C No sound Check audio cable connection from audio input sou
36. cting the cable AC Power Cords of MAC Adapter in the case of connecting Macintosh computer both projector and external equipment should be Audio Cables RCA x 2 or RCA x 1 Mini Plug mono x disconnected from AC outlet Turn projector and Speaker Cable Mini Plug stereo Bi equipment on before your computer is switched on IBM compatible computers or Macintosh computers VGA SVGA XGA SXGA Desktop type Laptop type Audio Output Mini Plug MAC Adapter Set the slide Switches accord ing to the chart on page 43 Cable Audio Cable Audio Cable A ee ee BNC x 5 RCA x 2 RCA Mini Plug RCA VGA Cable EE uS B V R AUDIO L N 6 e UNO RGB 1A y Use either RGB Terminal or SIPEG V R AUDIO LUN H V and V jacks VIDEO Y C Pb Cb Cr INPUT 3 AUDIO OUT VIDEO Y Pr Cr R AUDIO L RESET EXT SP 8Q R AUDIO L 9 e 6 e e x EXT SP R L Speaker Cable Audio Cable Mini stereo RCA x 2 Speaker 80 2W Audio Amplifier External Audio Equipment Audio Speaker stereo 13 BEFORE OPERATION TOP CONTROLS AND INDICATORS This projector has CONTROL BUTTONS TOP CONTROLS and
37. e projector to normal operation e If the projector has been dropped or the cabinet has been damaged f When the projector exhibits a distinct change in performance this indicates a need for service When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or injury to persons Upon completion of any service or repairs to this projector ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition Voor de klanten in Nederland Bij dit product zijn batterijen geleverd Wanneer deze leeg zijn moet u ze niet weggooien maar inleveren als KCA COMPLIANCES Federal Communication Commission Notice This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will
38. h Portuguese Dutch Swedish or Japanese PREPARATION NAME OF EACH PART OF PROJECTOR C FRONT TOP CONTROLS AND INDICATORS PROJECTION LENS LENS COVER gam SPEAKERS REMOTE RECEIVERS BACK EXHAUST VENTS A HOT AIR EXHAUSTED Air blown from Exhaust Vents is hot When using or installing projector the following precautions should be taken Do not put any flammable object near these vents Keep the rear grills at least 3 1m away from any object especially heat sensitive object Do not touch this area especially screws and metallic parts This area will become hot while projector is used This projector detects internal temperature and automatically controls operating power of Cooling Fans TERMINALS AND CONNECTORS POWER CORD CONNECTOR BOTTOM AIR INTAKE VENTS Side and Bottom This projector is equipped with Cooling Fans for protection from overheating Pay attention to the following to ensure ADJUSTABLE FEET proper ventilation and avoid a possible AND risk of fire and malfunction FEET LOCK LATCHES Do not cover vent slots Keep bottom clear of any object Obstructions may block cooling air LAMP COVER PREPARATION SETTING UP PROJECTOR CONNECTING AC POWER CORD This projector uses nominal input voltages of 100 120 V or 200 240 V AC The pr
39. ine batteries Replace two batteries at the same time Do not use a new battery with a used battery Avoid contact with water or liquid Do not expose Remote Control Unit to moisture or heat Do not drop Remote Control Unit batteries have leaked on Remote Control Unit carefully wipe the case clean and load new batteries j To insure safe operation please observe the following precautions 17 BEFORE OPERATION OPERATING ON SCREEN MENU HOW TO OPERATE ON SCREEN MENU 18 You can control and adjust this projector through ON SCREEN MENU Refer to the following pages to operate each adjustment on ON SCREEN MENU 1 DISPLAY MENU Press MENU button to display ON SCREEN MENU 2 MOVING POINTER Move the pointer see below or adjust the value of item by pressing POINT button s on Top Control or on Remote Control Unit Pointer is the icon on ON SCREEN MENU to select the item See the figures on the section FLOW OF ON SCREEN MENU OPERATION below 3 SELECT ITEM Select the item by pressing SELECT button REMOTE CONTROL LENS SHIFT KEYST 271 Used to move the C xt Pointer UP DOWN RIGHT LEFT SELECT MENU NORMA gt C e C SELECT BUTTON Used to select the item TOP CONTROL Used to select the item J ware 6 y e e POINT BUTTONS Used to move the Pointer UP DOWN RIGHT LEFT FLOW OF ON SCREEN MENU OPERATION Display ON SCREEN ME
40. is left unattended and unused for long periods of time unplug it from the wall outlet This will prevent damage due to lightning and power line surges Do not expose this unit to rain or use near water for example in a wet basement near a swimming pool etc Do not use attachments not recommended by the manufacturer as they may cause hazards Do not place this projector on an unstable cart stand or table The projector may fall causing serious injury to a child or adult and serious damage to the projector Use only with a cart or stand recommended by the manufacturer or sold with the projector Wall or shelf mounting should follow the manufacturer s instructions and should use a mounting kit approved by the manufacturers An appliance and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the appliance and cart combination to overturn Slots and openings in the back and bottom of the cabinet are provided for ventilation to insure reliable operation of the equipment and to protect it from overheating The openings should never be covered with cloth or other materials and the bottom opening should not be blocked by placing the projector on a bed sofa rug or other similar surface This projector should never be placed near or over a radiator or heat register This projector should not be placed in a built in installation such as a book case unless proper ven
41. mputer connect your Wired Remote Control Connect Connect composite video output to computer to this terminal Remote Control Unit to this jack with VIDEO Y separate video outputs to Remote Control Cable supplied VIDEO Y and C Pb Cb or component S VIDEO INPUT JACK Refer to page 16 17 video outputs to VIDEO Y C Pb Cb and Connect S VIDEO output P Ref P12 13 r Cr Refer to 13 from video equipment to AUDIO INPUT JACKS RGB TERMINAL this jack Refer to P12 Connect audio output from computer or video equipment to Connect computer output to these jacks Refer to P12 13 this terminal Refer to P13 E ES a M a SS SERIAL PORT R C JACK R AUDIO L MONO INPUT 2 S g mv y S VIDEO R AUDIO L MONO VIDEO Y C Pb Cb Pr Cr INPUT 3 AUDIO OUT VIDEO Y Pb Cb Pr Cr R AUDIO L EXT SP 80 R AUDIO L VIDEO INPUT JACKS RESET BUTTON AUDIO OUTPUT JACKS Connect video output to these This projector uses a micro processor to Connect an external audio jacks control the unit Occasionally the micro amplifier to these jacks Connect composite video processor may malfunction and need to Refer to P12 13 output to VIDEO Y or connect be reset This can be done by pressing component video outputs to RESET button with a pen which will VIDEO Y Pb Cb and Pr Cr shut down and restart the unit Do not EXTERNAL SPEAKER JACK System to this jack Refer to P12 13 11 CONNECTIN
42. ock Latches Position and keystone distortion of the image can be adjusted using Menu Operation Refer to P 21 and 36 FEET LOCK LATCHES ADJUSTABLE FEET MOVING PROJECTOR Use Carry Handle when moving projector When moving projector replace Lens Cover and retract Adjustable Feet to prevent damage to Projection Lens and cabinet When this projector is not in use for an extended period put it into the case Dust Cover supplied with this projector N CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR Do not drop or bump projector otherwise damages or malfunctions may result When carrying projector use a suitable carrying case Do not transport projector by using a courier or transport service in an unsuitable transport case This may cause damage to projector To transport projector through a courier or transport service consult your dealer for best way 10 CONNECTING PROJECTOR TERMINALS OF PROJECTOR This projector has INPUT TERMINALS and OUTPUT TERMINALS on its side for connecting computers and video equipment Refer to the figure on pages 11 to 13 and connect properly qun BNC JACKS SERIAL PORT TERMINAL R C JACK INPUT OUTPUT ERR TERMINALS Connect computer or video output to When controlling this projector When using Remote Control Unit as these jacks by co
43. ojector automatically selects the correct input voltage It is designed to work with single phase power systems having a grounded neutral conductor To reduce the risk of electrical shock do not plug into any other type of power system Consult your authorized dealer or service station if you are not sure of the type of power supply being in use Connect projector with the peripheral equipment before turning projector on Refer to pages 11 13 for connection CAUTION For safety unplug the AC Power Cord when the appliance is not used cL cede MAIN ON OFF SWITCH Connect AC Power Cord supplied to projector The AC outlet must be near this equipment and must be easily accessible NOTE ON THE POWER CORD The AC Power Cord must meet the requirement of the country where you use the projector Confirm the AC plug type with the chart below and the proper AC Power Cord must be used If the supplied AC Power Cord does not match the AC outlet contact your sales dealer Projector side cel gx OR To the POWER CORD CONNECTOR on pro jector For the U S A and Canada Ground ae pe To the AC Outlet 120 V AC AC Outlet side For Continental Europe qu To the AC Outlet 200 240 V AC For the U K gt To AC Outlet w 200 240 V AC PREPARATION POSITIONING THE PROJECTOR This projector is designed to project on a flat projection s
44. play Press POINT LEFT RIGHT button to adjust value From 0 to 255 HI Total dots The number of total dots in one horizontal period Press POINT LEFT RIGHT button s and adjust number to match your PC image Horizontal Adjust horizontal picture position button s to adjust the position Adjust vertical picture position Press POINT LEFT RIGHT button s to adjust the position Press SELECT button to show the information of computer selected The number of the total horizontal lines Press POINT LEFT RIGHT button s and adjust number to match your PC image Adjusts clamp level adjustment Press POINT LEFT RIGHT When the image has a dark bar s try this PC ADJUST MENU 1 PC ADJUST Menu icon Move the red frame icon to the item and press SELECT button Oe Shows the status Stored Free of Mode Selected Mode Fine sync Modet J Stored 1 mf 01550 Press POINT LEFT RIGHT button to adjust the value Press SELECT button at this icon to adjust Total lines Clamp Display area Horiz scale or Vert scale Be 8 E 4 2 ul H Sync freq V Syncfreg 60 0 0000 KD 10242 L0 768 EID Press SELECT button at Current mode icon to show the information of computer connected See Ea eh eee MC e 25 COMPUTER MODE 26 Selects area displayed with this projector Select the resolution at the Displ
45. ppears for 5 minutes 2 When Projection Lamp turned off READY Indicator turns off Cooling Fans operate and Projection Lamp is turned off for 90 seconds During this Cooling Down period projector cannot be turned on 3 When Projection Lamp has cooled down READY Indicator flashes and Projection Lamp can be turned on again Power Management mode In this Power Management mode Projection Lamp is automatically turned on when the input signal connected or projector is operated with any button on the Top Control or on the Remote Control Unit When this function is On projector is automatically turned on just by switching MAIN ON OFF SWITCH on Note Be sure to turn projector off properly refer to the section TURNING OFF THE PROJECTOR on page 20 If projector is turned off in the wrong steps On Start function does not operate properly EJ Remote control This projector has two different remote control codes the factory set normal code Code 1 and the secondary code Code 2 This switching function prevents the remote control operation mixture jam when operating several projectors or video equipment together When operating projector in Code 2 both projector and Remote Control must be switched to Code 2 To change the code of Projector Set the Remote control in the SETTING MENU to Code 2 To change the code of the Remote Control Press both MENU and NORMAL buttons on the Remote Control
46. r Cr JACKS Projector automatically detects incoming Video signal and adjusts itself to optimize its performance COMPONENT VIDEO SIGNAL FORMAT If projector cannot reproduce proper video image it is necessary to select a specific component video signal format among 480i 575i 480p 575p 720p 1035i and 10801 AV SYSTEM MENU VIDEO OR S VIDEO se Eel SYSTEM Menu icon This box indicates the system being selected Move the pointer to the System and press SELECT button AV SYSTEM MENU COMPONENT VIDEO SYSTEM EJ Auto __ SYSTEM Menu icon This box indicates the system being selected Move the pointer to the System and press SELECT button VIDEO MODE PICTURE IMAGE ADJUSTMENTS IMAGE LEVEL SELECT DIRECT Select image level among Standard Cinema Image 1 Image 2 IMAGE button Image 3 and Image 4 by pressing IMAGE button on the Remote Standard Control Unit Normal picture level preset on this projector This normal picture level can also be selected by pressing NORMAL button Picture level adjusted for the picture with fine tone IMAGE 1 4 User preset picture adjustment in IMAGE ADJUST Menu P34 IMAGE LEVEL SELECT MENU 1 Press MENU button and ON SCREEN MENU will appear Press IMAGE SELECT MENU POINT LEFT RIGHT button to move a red frame pointer to fa IMAGE SELECT Menu icon 2 Press POINT DOWN button to move a red fr
47. r portability durability and ease of use The projector utilizes built in multimedia features a palette of 16 77 million colors and matrix liquid crystal display LCD technology Compatibility This projector widely accepts various video and computer input signals including 6 Color Systems NTSC PAL SECAM NTSC 4 43 PAL M or PAL N color system can be connected Component Video Component video signals such as a DVD player output high definition TV signals including 480i 480p 575i 575p 720p 1035i 1080i 50 or 10801 60 can be connected e S Video S Video signals such as a S VHS VCR output signals can be connected Computers IBM compatible and Macintosh computers up to 1280 x 1024 resolution High Resolution Image This projector provides 1366 x 768 dots resolution for computer input and 800 horizontal TV lines The resolution from computer between XGA 1024 x 768 and SXGA 1280 x 1024 is compressed into 1024 x 768 dots This projector cannot display image of over 1280 x 1024 dots When the resolution of your computer is over than 1280 x 1024 reset computer output for lower resolution Multi Scan System This projector has Multi Scan System to conform to almost all computer output signals quickly There is no need for complicated manual adjustment of frequency and other settings One Touch Auto PC Adjustment Incoming computer video signals are recognized and the best adjustment is
48. rce Adjust the audio source Press VOLUME button Press MUTE button 40 APPENDIX Problem Try these Solution Remote Control Unit Check the batteries does not work Make sure nothing is between the Remote Receiver and the Remote Control Unit Make sure you are not too far from projector when using the Remote Control Unit Maximum operating range is 16 4 5m Make sure the code of the Remote Control is set to conform to projector See SETTING section on page 36 37 WARNING High voltages are used to operate this projector Do not attempt to open the cabinet If the problem still persists after following all operating instructions contact the sales dealer where you purchased projector or the service center Give the model number and explain the difficulty We will advise you how to obtain service Laboratories Inc It is designed and manufactured to meet rigid U L safety standards C L US LISTED against risk of fire casualty and electrical hazards U This symbol on the nameplate means the product is Listed by Underwriters 41 APPENDIX TECHNICAL SPECIFICATIONS 42 Projector Type Multi media Projector Dimensions W x H x D 12 44 x 6 46 x 18 9 816mm x 164mm x 480mm Net Weight 20 3 Ibs 9 2 kg LCD Panel System 1 35 TFT Active Matrix type 3 panels Panel Resolution 1366 x 768 dots Number of Pixels 3 147 264 136
49. s to be built into a compartment or similarly enclosed the minimum distances must be maintained Do not cover the ventilation slot on the projector Heat build up can reduce the service life of your 50cm 50cm 50cm projector and can also be dangerous Do not put any flammable object or spray can near the projector hot air is exhausted from the ventilation holes If the projector is not to be used for an extended time unplug the projector from the power outlet READ AND KEEP THIS OWNER S MANUAL FOR LATER USE CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT REFER SERVICING TO QUALIFIED SERVICE PERSONNEL THIS SYMBOL INDICATES THAT DANGEROUS THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT VOLTAGE CONSTITUTING A RISK OF ELECTRIC OPERATING AND MAINTENANCE INSTRUCTIONS IN THE SHOCK IS PRESENT WITHIN THIS UNIT OWNER S MANUAL WITH THIS UNIT SAFETY INSTRUCTIONS All the safety and operating instructions should be read before the product is operated Read all of the instructions given here and retain them for later use Unplug this projector from AC power supply before cleaning Do not use liquid or aerosol cleaners Use a damp cloth for cleaning Follow all warnings and instructions marked on the projector For added protection to the projector during a lightning storm or when it
50. the Display area dialog box appears SRW ES E s BR To store the adjustment data This Mode has parameters being stored Vacant Mode Shows values of Fine sync Horizontal Vertical Display area H and Display area V Stored icon To clear the adjustment data Mode Free _ 2 O Which mode to free Close the dialog box Mode free icon 20 WE EWE we eo COMPUTER MODE COMPATIBLE COMPUTER SPECIFICATIONS Basically this projector can accept the signal from all computers with the V H Frequency mentioned below and less than 180 MHz of Dot Clock ON SCREEN H Freq V Freq ON SCREEN H Freq V Freq DISPLAY RESOLUTION Hz DISPLAY RESOLUTION Hz 1 640 x 480 31 47 5988 XGA11 1024x768 61 00 75 70 VGA 2 720 x 400 31 47 70 09 12 1024x768 35 522 Wto VGA 3 640 x 400 31 47 70 00 XGA13 1024x768 46 90 58 20 VGA 4 640 x 480 37 86 74 38 XGA14 1024x768 47 00 58 30 VGA 5 640 x 480 37 86 72 81 XGA15 1024 768 58 03 72 0 VGA 6 640 x 480 37 50 75 00 MAC 19 1024 768 60 24 75 08 VGA 7 640 x 480 43 209 85 00 21 1152x870 68 68 75 06 MACLC13 640x480 34 97 66 60 SXGA1 1152x864 64 20 70 40 13 640 x 480 35 00 66 67 SXGA2 1280x1024 62 50 58 60 RGB 15 625 SXGA3 1280x1024 63 90 60 00 RGB 15 734 SXGA4 1280x1024 63 34 59 98 SVGA1 800x600 35 156 56 25 S
51. the lamp assembly 1 Turn off projector and disconnect AC plug Allow projector to cool for at least 45 minutes Remove a screw with a screwdriver and remove Lamp Cover Handle Replace Lamp Assembly with a new one and tighten 2 screws Make sure that Lamp Assembly is set properly Replace Lamp Cover and tighten a screw 3 Remove 2 screws and pull out Lamp Assembly by grasping LAMP ASSEMBLY 5 Connect AC Power Cord to projector and turn on projector 6 Reset Lamp Replace Counter refer to the section Lamp Replace Counter below NOTE Do not reset Lamp Replace Counter when Projection Lamp is not replaced ORDER REPLACEMENT LAMP Replacement Lamp can be ordered through your dealer When ordering the Lamp give the following information to the dealer Model No of your projector PLV 60 Replacement Lamp Type No POA LMP28 Service Parts No 610 285 4824 LAMP REPLACE COUNTER Be sure to reset Lamp Replace Counter when Lamp Assembly is replaced When Lamp Replace Counter is reset LAMP REPLACE Indicator stops lighting 1 Turn projector on press MENU button and ON SCREEN MENU will appear Press POINT LEFT RIGHT button s to move a red frame pointer to SETTING Menu icon refer to page 36 37 2 Press POINT DOWN button to move a red frame pointer to Lamp counter reset and then press SELECT button The message Lamp replace counter reset is displayed Move the pointer to Yes and then press SELEC
52. tilation is provided Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the projector This projector should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supplied consult your authorized dealer or local power company Do not overload wall outlets and extension cords as this can result in fire or electric shock Do not allow anything to rest on the power cord Do not locate this projector where the cord may be damaged by persons walking on it Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions a When the power cord or plug is damaged or frayed b If liquid has been spilled into the projector c If the projector has been exposed to rain or water d If the projector does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore th
53. ton to increase volume and button decreasing MUTE SETTING Press MUTE button on Remote Control Unit to cut off sound To restore sound to its previous level press MUTE button again or press Volume button s Indicates the roughly level of volume A Volume amp Mute Press MUTE button to set Mute function On or Off The display disappears after 4 seconds COMPUTER MODE SELECTING INPUT SOURCE DIRECT OPERATION INPUT button Choose either Input 1 or Input 2 by pressing INPUT button on Top Control or on Remote Control Unit MENU OPERATION 1 Press MENU button and ON SCREEN MENU will appear Press INPUT MENU POINT LEFT RIGHT button to move a red frame pointer to INPUT Menu icon Press POINT DOWN button to move a red arrow pointer to either Input 1 or Input 2 that you want to choose and then press SELECT button When choosing Input 2 Source Select Menu will appear Move POINTER to RGB and then press SELECT button Input 2 p accepts R G B H V and V computer signals P 13 g Y PbiCbPriCr INPUT Menu icon Move POINTER red arrow to Input 1 or 2 and press SELECT button Source Select Menu Input 2 Move POINTER to RGB and press SELECT button SELECTING COMPUTER SYSTEM This projector automatically tunes to most different types of computers based on VGA SVGA XGA or SXGA refer to COMPATIBLE COMPUTER SPECIFICATION on page 27 When selecting Computer this
54. tortion to correct P21 36 keystone POINT BUTTONS Used to move Pointer or to adjust the item on On Screen MENU And it is also used to pan image in Digital Zoom mode P30 NORMAL BUTTON Used to reset to normal picture adjustments preset by the factory or to reset screen adjustment in True mode Digital Zoom mode or Keystone mode P21 28 30 33 Point Remote Control toward projector Remote Receiver whenever pressing the buttons Maximum operating range for Remote Control is about 16 4 bm and 60 in front and rear of projector 609 3 16 4 5 m 609 16 4 5 m BEFORE OPERATION WIRED REMOTE CONTROL OPERATION When using this Remote Control Unit as Wired Remote Control Connect Remote Control Unit to R C JACK with Remote Control Cable supplied Batteries installation is required when using as Wired Remote Control Unit Remote Control Cable supplied REMOTE CONTROL BATTERIES INSTALLATION 1 Remove the battery 2 Slide 2 batteries into 3 Replace the compartment compartment lid the compartment lid Slide the lid upward Press the lid downward and slide it Two AA size batteries For correct polarity and be sure the battery terminals are in contact with pins in the compartment Use 2 AA or R06 type alkal
55. urface and it can be focused from 4 43 1 35m 45 9 14 0m Refer to the figure below to adjust the screen size RECOMMENDATION Brightness in the room has a great influence on picture quality It is recommended to limit ambient lighting in order to provide the best image 45 9 14 0m 34 1 10 4m Zoom 400 ____ 300 22 9 7 0m 11 5 3 5m 1443 1 35m Width x Height 886 x 498 mm 2215 x 1245 mm 4430 x 2490 mm 6644 x 3736 mm 8860 x 4980 mm LENS SHIFT ADJUSTMENT Projection Lens can be moved up and down with Motor driven Lens Shift function This function makes it easy to provide the projected image where you want Refer to P 21 for operation n fe p Highest Lens Shift Lowest Lens Shift H1 H2 10 9 1 H3 H4 1 3 9 4 NS A NOTE Screen size and lens shift ratio on the above charts are standard values and they may change by positioning conditions PREPARATION ADJUSTABLE FEET Picture tilt and projection angle can be adjusted by rotating Adjustable Feet Projection angle can be adjusted to 9 0 degrees 1 Lift the front of projector and pull Feet Lock Latches on both sides of projector 2 Release Feet Lock Latches to lock Adjustable Feet and rotate Adjustable Feet to fine tune position and tilt 3 To shorten Adjustable Feet lift the front of projector and pull and undo Feet L
56. ut2 If projector cannot reproduce proper video source select correct input source through MENU OPERATION see below Ens MENU OPERATION I Press MENU button and ON SCREEN MENU will appear Press INPUT MENU POINT LEFT RIGHT button to move a red frame pointer to om grs INPUT Menu icon Move the arrow to the Input source and press SELECT button Press POINT DOWN button to move a red arrow pointer to either Input 2 or Input 3 that you want to choose and then press SELECT button Source Select Menu appear 3 Move the pointer to the source that you want to select and then press SELECT button Source Select Menu Input 2 3 Move the arrow to the source and press SELECT button 31 VIDEO MODE SELECTING VIDEO SYSTEM 32 1 Press MENU button and ON SCREEN MENU will appear Press POINT LEFT RIGHT buttons to move a red frame pointer to SYSTEM Menu icon 2 Press POINT DOWN button to move a red arrow pointer to the system that you want to select and then press SELECT button VIDEO JACK Y C JACKS OR S VIDEO JACK _ Projector automatically detects incoming Video system and adjusts itself to optimize its performance When Video System is PAL M or PAL N select system manually PAL SECAM NTSC NTSC4 43 PAL M PAL N If projector cannot reproduce proper video image it is necessary to select a specific broadcast signal format among PAL SECAM NTSC NTSC 4 43 PAL M and PAL N Y Pb Cb P

Sanyo PLV-60 Projector User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents