Home

Samsung SC-D352 Camcorder User Manual

1. Protect When you try to delete to protected image Cancel the protection of image Read error The Camcorder can not playback Format a Memory card or insert Memory card recorded on this Camcorder Write error The Camcorder can not record Format a Memory card or change to a new Memory card Not Formatted The Memory card needs to format Format a Memory card see page 101 Now deleted When progressing file delete Wait until delete has been finished Memory Card error If inserted Memory Card is not recognized by the Camcorder Eject and re insert the memory card Try another Memory Card Troubleshooting If these instructions do not solve your problem contact your nearest Samsung authorized service center Symptom Explanation Solution You cannot switch the Camcorder on Check the Battery pack or the AC Power adapter Start Stop button does not operate while recording Check the Power switch is set to CAMERA You have reached the end of the cassette Check the record protection tab on the cassette The Camcorder shuts off automatically You have left the Camcorder set to STBY for more than 5 minutes without using it The Battery pack is fully exhausted Charge runs out quickly The atmospheric temperature is too low The Battery pack has not been charged fully The Battery pack is completely dead and
2. f you want to transmit data to a PC you must install an IEEE 1394 add on card into the PC not supplied The frame rate for video capture is dependent on the capacity of the PC Notes m When you transmit data from the Camcorder to another DV device some functions may not work If this occurs please reconnect the DV cable or turn the power OFF and ON again When you transmit data from the Camcorder to PC PC function button is not available in M Player mode Do not use the Camcorder and IEEE1394 together as this will cause IEEE1394 to shut off Do not connect the Camcorder to a PC using both DV and USB cables It may not operate properly Operation is not guaranteed for all computer environments recommended above The IEEE1394 cable DV cable is sold separately Video Capture software is commercially available Most DV enabled PCs have a 6 pin socket In this case a 6pin 4pin cable is required for the connection Most DV enabled Notebooks and Laptops have a 4 pin socket Use a 4pin 4pin cable for the connection DIS and COLOR NITE SHUTTER are not available when in DV IEEE1394 mode If DV IEEE1394 mode is set DIS and COLOR NITE SHUTTER modes will be released IEEE 1394 Data Transfer System Requirements CPU faster Intel Pentium III 450MHz compatible Operating system Windows 98SE ME XP Mac OS 9 1 10 2 Main memory more than 64 MB RAM IEEE1394 add on card or built in IEEE1394 card Recording with a DV Connec
3. Notes and Safety Instructions Notes regarding the Rotation of the LCD Screen Please rotate the LCD screen carefully as illustrated Over rotation may cause damage to the inside of the hinge that connects the LCD screen to the Camcorder 1 LCD screen closed 2 Standard recording using the LCD screen Open the LCD screen with your finger 3 Recording when looking at the LCD screen from the top 4 Recording when looking at the LCD screen from the front 5 Recording when looking at the LCD screen from the left 6 Recording with the LCD screen closed Notes and Safety Instructions Notices regarding Copyright Television programs video tapes DVD titles films and other program materials may be copyrighted Unauthorized copying of copyrighted material may be against the law All the trade names and registered trademarks mentioned in this manual or other documentation provided with your Samsung product are trademarks or registered trademarks of their respective holders Notes regarding Moisture Condensation 1 Asudden rise in atmospheric temperature may cause condensation to form inside the Camcorder for example m When you move the Camcorder from a cold location to a warm location e g from outside to inside during winter When you move the Camcorder from a cool location to a hot location e g from inside to outside during the summer 2 If the L DEW protection feature is act
4. se 1 Set the Power switch to CAMERA 2 Set the Mode switch to TAPE SC D353 D354 D355 only 3 Press the COLOR NITE SHUTTER button 4 Each time you press the COLOR NITE SHUTTER button shutter speed is changed to gt Color N 1 30 Color N 1 15 and off SC D351 D353 only gt Color N 1 30 Color N 1 15 Color N 1 15 G and off SC D352 D354 D355 only Notes The COLOR NITE SHUTTER will not turn ON or OFF while you are recording When using COLOR NITE SHUTTER the image takes on a slow motion like effect When using the COLOR NITE SHUTTER function the focus adjusts slowly and the white dots may appear on the screen this is not a defect 4 E COLOR NITE SHUTTER is not available while DIS Photo image recording or EASY Q is in use z m Digital Zoom Photo image recording 16 9 Wide Emboss2 Pastel2 Mirror or Mosaic is not available in the COLOR NITE SHUTTER mode If DIS or EASY Q is set COLOR NITE SHUTTER mode will be released gt Color N 1 30 Basic Recording Using the Color Nite Shutter with LED Light SC D352 D354 D355 only COLOR NITE SHUTTER function works only in Camera mode The LED light enables you to record a subject in dark places without sacrificing color The LED light can be used with COLOR NITE SHUTTER function only Set the Power switch to CAMERA in Set the Mode switch to TAPE 3 Press the COLOR NITE LED LIGHT button until Color N 1 15 E4 appear
5. 1 Set the Power switch to PLAYER 2 Set the Mode switch to MEMORY CARD C gt DCIM 100 SSDVC DCAM 0001 DCAM 0002 101SSDVC a 2 lt Still image gt _ MSAMSUNG SSMOV 100SSMOV Ne J lt Moving image gt F B M Player 000 0000 File number Folder number AS A Digital Still Camera Mode SC D353 D354 D355 only Selecting the Built in Memory SC D354 D355 only Built in memory setting is available in the Player M Cam M Player modes SC D354 32MB SC D355 64MB Images can be stored and played back using the built in memory Hence set the memory type before storing and playing back images Set the Power switch to CAMERA or PLAYER Set the Mode switch to TAPE or MEMORY CARD Press the MENU button The menu list will appear Move the Menu selector to the left or right to select Memory then press the Menu selector Move the Menu selector to the left or right to select Memory Type then press the Menu selector Move the Menu selector to the left or right to select Int Memory or Memory card then press the Menu selector To exit press the MENU button Using Quick Menu Memory Type 1 2 3 4 A Press the Menu selector Move the Menu selector to left or right to select Memory Type then press the Menu selector Move the Menu selector to the left or right to select Int Memory or Memory card then press the Menu selector
6. Please rotate the LCD screen carefully as excessive rotation may cause damage to the inside of the hinge that connects the LCD screen to the Camcorder Basic Recording Making your First Recording 1 Connect a power source to the Camcorder see page 20 A Battery pack or a AC Power adapter Insert a cassette See page 36 2 Remove the Lens cover 3 Set the Power switch to CAMERA Open the LCD screen Set the Mode switch to TAPE SC D353 D354 D355 only Make sure that STBY is displayed If the write protection tab of the cassette is open set to save O STOP and Protection will be displayed 8 Release the write protection tab to record Make sure the image you want to record appears on the LCD screen or Viewfinder m Make sure the battery level indicates that there is enough remaining power for your expected recording time 4 To start recording press the Start Stop button REC e is displayed on the LCD screen To stop recording press the Start Stop button again STBY is displayed on the LCD screen Note Detach the Battery pack when you are finished recording to prevent unnecessary battery power consumption Basic Recording Using EASY Q Mode for Beginners Set the Power switch to CAMERA The EASY Q mode works only in Camera mode The EASY Q mode allows a beginner to easily make good recordings 2 Set the Mode switch to TAPE SC D353 D354 D355 only 3 By pres
7. USB Connection speed depending on the System High speed USB connection is supported by Microsoft Windows device drivers only _ zZ m Windows 98SE ME Full Speed USB Windows 2000 High speed USB on a system with Service Pack 4 or later installed m Windows XP High speed USB on a system with Service Pack 1 or later installed System Requirements Windows System Minimum Recommended CPU Intel Pentium III 600MHz Intel Pentium 4 2GHz OS Operating System Windows 98SE ME Windows 2000 XP Memory 128MB 512MB HDD capacity 1GB or more 2GB or more Resolution 1024 x 768 dots 1024 x 768 dots 24bit Color 24bit Color USB USB1 1 USB2 0 High Speed tis not available for Macintosh systems Notes USB 2 0 works only for removable disk functions m Ona slower PC than recommended movie playback may not be smooth or video editing may take a long time m Ona slower PC than recommended movie playback may skip frames or operate unexpectedly m Intel Pentium III or Pentium 4 is a trademark of the Intel Corporation m Windows is a registered trademark of the Microsoft Corporation All other brands and names are property of their respective owners m Operations are not guaranteed for all of the recommended computer environments mentioned above m Do not connect the Camcorder to a PC using both DV and USB cables It may not operate properly L In M Cam or M Player mode be sure
8. Using the Fade In and Out To Start Recording c cesses To Stop Recording use Fade In Fade Out Using Back Light Compensation Mode BLC Using the Color Nite Shutter Using the Color Nite Shutter with LED Light SC D352 D354 D355 only Nite Pix 0 lux recording SC D352 D354 D355 only Power Nite Pix SC D352 D354 D355 only AGVanced RECOFCING 2 oso on E R E E Er reteset AR R ERE N Use of various Functions Setting Menu Items 01 Function availability in eac Selecting the Record Mode Selecting Audio Mode Cutting Off Wind Noise Wind Cult Setting the Shutter Speed amp Exposure Recommended Shutter Speeds when Recording Auto Focus Manual Focus Auto Focusing Manual Focusing Setting the White Balance Using Quick Menu White Balance Setting the Digital Image Stabilizer DIS Using Quick Menu Digital Image Stab Programmed Automatic Exposure Modes Program AE Setting the Program AE cccseeseeee Using Quick Menu Program AE Contents Applying Digital Effects Selecting the Digital Effects Zooming In and Out with Digital Zoom Setting the Digital Zoom Photo Image Recording Searching fora Photolmage zearen renat aee T aeaa Eai EUA Kaana ENE ENAERE AA SE ENET oa ada VAa SANAA EEEE ADEI A NAANA EEEE EET 68 ba 09 Playing Back a Tape You ha
9. 4 STBY ae 60min m The Power Nite Pix function will not turn ON or OFF while you are recording The maximum recording distance using the infrared light is about 3 m about 10 feet gt m f you use the Power Nite Pix function in normal recording situations ex outdoors by day oS the recorded picture may contain unnatural colors Powar Nito Rix m Inthe Power Nite Pix mode certain functions are not available such as Exposure White Balance C Coor nans j A Program AE Digital Effect BLC Digital Zoom and Manual Focus Advanced Recording Use of various Functions Setting menu items Main Menu Sub Menu Functions Axalabie mode Page Camera Player M Cam MPlayer Camera Program AE Selecting the Program AE Function Vv 63 64 White Balance Setting White Balance Vv Vv 59 Digital Effect Setting the Digital special effect Vv 65 66 DIS Selecting the Digital Image Stabilizing Vv 61 Digital Zoom Selecting Digital Zoom Vv 67 Tape Photo Search Searching pictures recorded in Tape Vv 68 Photo Copy Copying still images from a cassette to Memory card Y 105 Audio Select Selecting the Audio playback channel Vv 78 Record Rec Mode Selecting the recording speed Vv Vv 54 Audio Mode Selecting Sound Quality for recording Vv Vv 55 Wind Cut Minimizing wind noise Vv Vv 56 AV In Out Selecting the AV input output Vv 76 Memory Memory Type Selecting t
10. Move the Menu selector to the left or right to select Record then press the Menu selector Move the Menu selector to the left or right to select Rec Mode then press the Menu selector Move the Menu selector to the left or right to select desired record mode SP or LP then press the Menu selector To exit press the MENU button The selected icon will be displayed D Notes A We recommend that you use this Camcorder to play back any tapes recorded on this Camcorder Playing back a tape recorded in other equipment may produce mosaic shaped distortion When you record a tape in SP and LP modes or LP mode only the playback picture may be distorted or the time code may not be written properly if there is a gap between scenes Record using SP mode for best picture and sound quality J Camera Mode Rec Mode PSP amp Audio Mode gt 12Bit Wind Cut Off C Move Select DEY Exit p J Camera Mode Audio Mode Wind Cut Move Select DEY Exit Gi STBY my 60min Advanced Recording Selecting Audio Mode The Audio Mode function works in both Camera and Player modes This Camcorder records sound in two ways 12Bit 16Bit 12Bit You can record two 12Bit stereo sound tracks The original stereo sound can be recorded onto the Main Sound1 track Additional stereo sound can be dubbed onto the Sub Sound2 track 16Bit You can record one high quality stereo sound using the 16
11. Tanguage The Demonstration will begin Demonstration 7 To quit the Demonstration press the MENU button Move PaSelect DEN Ext Notes enoma canore m The Demonstration mode is automatically activated when the Camcorder is left idle for more than 10 minutes after switching to the Camera mode no tape is inserted in the Camcorder f you press other buttons FADE BLC PHOTO EASY Q during the Demonstration mode the demonstration stops temporarily and resumes 10 minutes later if you do not operate any other Digital Camcorder SC D352 D354 D355 only a a While setting the NITE PIX to ON the Demonstration function does not work Display Menu Setting Adjusting the LCD Screen This function works in Camera Player M Cam M Player modes Your Camcorder is equipped with a 2 36 inch color Liquid Crystal Display LCD screen which enables you to view what you are recording or playing back directly Depending on the conditions under which you are using the Camcorder indoors or outdoors for example you can adjust LCD Bright LCD Color Set the Power switch to CAMERA or PLAYER Set the Mode switch to TAPE or MEMORY CARD SC D353 D354 D355 only Press the MENU button The menu list will appear Move the Menu selector to the left or right to select Display then press the Menu selector 4 Move the Menu selector to the left or right to select the item you want to adjus
12. The moving picture images on a Memory card are a smaller size and lower definition than images on tape MSAMSUNG The sound is recorded in mono T SSMOV The following functions are not allowed in M Cam Mode L 5 100ssmov DIS Digital Image Stabilizer Digital Zoom Fade Program AE Digital Effect Slow Shutter While recording on a Memory card don t insert or eject the tape as it may record noise lt Moving image gt While a Memory card don t eject the card or it may break the data on the Memory card or Memory card itself Turning the power off while accessing the memory card may damage the data stored on the memory card Digital Still Camera Mode SC D353 D354 D355 only MPEG Playback The MPEG Playback function works only in M Player mode You can play the moving picture images on the Memory card Stereo audio is played back at the same time Playing back on a PC shows better quality than on a TV 1 Set the Power switch to PLAYER 2 Set the Mode switch to MEMORY CARD 3 Press the MENU button The menu list will appear 4 Move the Menu selector to the left or right to select Memory then press the Menu selector 4 5 Move the Menu selector to the left or right to select M Play Select then press the Menu selector MPlay Select _ gt Photo 6 Move the Menu selector to the left or right to select Movie then press th
13. To exit press the MENU button M Cam Mode J Memory Type __ gt int Memory _ Photo Quality _ gt Fine Series Move Select DEY Exit S M Cam Mode v Int Memory amp Photo Quality Memory card f File No Move Select GQ Exit 60 E 2min a Memory Type Int Memory White Balance x Photo Quality Exposure Manual Focus I Exit Digital Still Camera Mode SC D353 D354 D355 only Selecting the Image Quality You can select the quality of a still images to be recorded Select the Image Quality 1 Set the Power switch to CAMERA 2 Set the Mode switch to MEMORY CARD 3 Press the MENU button The menu list will appear 4 Move the Menu selector to the left or right to select Memory then press the Menu selector z NS 5 Move the Menu selector to the left or right to select Photo Quality then press the Menu d 1 tare MEMORY CARD selector 6 Move the Menu selector to the left or right to select desired image quality Super Fine Fine Normal then press the Menu selector ON Wicam Mode 7 To exit press the MENU button The selected icon will be displayed J Photo Quality _ gt Super Fine Series Number of Images on the Memory Card QUALITY 8MB 16MB Move seee EE j Super Fine Approx 34 Approx 68 6 ve M Cam Mode Fine Approx 45 Approx 90 v Super Fine ef Fine Ey Normal ay Normal
14. To use it again press the Start Stop button or set the Power switch to Off and then back to CAMERA This auto power off feature is designed to save battery power Record Search REC SEARCH Note Mosaic shaped distortion may appear on the screen while in Record Search mode You can view a recording using the REC SEARCH function in STBY mode REC SEARCH enables you to play the recording backwards and REC SEARCH enables you to play it forwards for as long as you keep each button pressed down If you press the REC SEARCH button in STBY mode your Camcorder will play in reverse for 3 seconds and return to the original position automatically Basic Recording Setting the Zero Memory SC D354 D355 only The ZERO MEMORY function works in both Camera and Player modes You can mark a point on a tape that you want to return to following playback 1 Set the Power switch to CAMERA or PLAYER 2 Set the Mode switch to TAPE 3 Press the ZERO MEMORY button on the remote control before the recording or during playback at the point where you wish to return The time code is changed to a tape counter that is set to ZERO MEMORY with the gt 0 00 00 ZERO MEMORY indicator If you want to cancel the ZERO MEMORY function press the ZERO MEMORY button again 4 Finding the zero position When you have finished playback fast forward or rewind the tape in stop mode Ar 9 one The tape stops automatical
15. press the MENU button il eet O 2 46 N otes 800x600 When there is no stored picture on the Memory card the message No image will be displayed m f an erroneous image file is found on the Memory card the message Memory card error will be displayed ss 7 It may be caused by copying images from different digital devices Co wooo Formatting the Memory card will delete all the stored images see page 101 To protect important pictures from accidental deletion activate the image protection refer to page 97 Deleting all files using the Delete All menu may take a while To delete all files much faster format the memory card after backing up the files into other storage device Digital Still Camera Mode SC D353 D354 D355 only Formatting the Memory Card The Format function works only in M Player mode You can use the memory format functions to completely delete all images and options on the Memory card including protected images The format function restores the Memory card to its initial state The Memory card supplied with this Camcorder has been formatted already Attention If you execute the memory format function all images will be erased completely and erased images cannot be recovered Set the Power switch to PLAYER Set the Mode switch to MEMORY CARD Press the MENU button The menu list will appear Move the Menu selector to the left or right to select
16. 4 Negative mode This mode reverses the colors creating a negative image 5 Mirror mode This mode cuts the picture in half using a mirror effect 6 BLK amp WHT mode This mode changes the images to black and white 7 Emboss1 mode This mode creates a 3D effect embossing 8 Emboss2 mode This mode creates a 3D effect embossing on surrounding area of an image 9 Pastel mode This mode applies a pale pastel drawing effect to an image 10 Pastel2 mode This mode applies a pale pastel drawing effect to surrounding area of an image 11 16 9 Wide mode Select to record a picture to be played back on a 16 9 Wide TV Advanced Recording Selecting the Digital Effects 1 Set the Power switch to CAMERA 2 Set the Mode switch to TAPE SC D353 D354 D355 only 3 Press the MENU button The menu list will appear 4 Move the Menu selector to the left or right to select Camera then press the Menu selector 5 Move the Menu selector to the left or right to select Digital Effect then press the Menu selector 6 Move the Menu selector to the left or right to select the desired Digital Effect mode then press the Menu selector D AE m The display mode is set to the selected mode 7 To exit press the MENU button cece An Digital Effect gt Off Notes ee The Pastel2 Emboss2 16 9 Wide Mirror or Mosaic modes are not available while DIS or COLOR NITE SHUTTER is in use go EE ree m Digital Effect modes
17. ADV Frame advance X2 SLOW buttons are located on the remote control only SC D354 D355 only To prevent tape and head drum wear your Camcorder will automatically stop if it is left in still or slow modes for more than 3 minutes Playback Pause REC SEARCH FADE BLC Press the II PLAY STILL button during playback To resume playback press the II PLAY STILL button CJL JL Picture Search Forward Reverse Press the 44 gt gt REW FF buttons during playback or still mode To resume normal playback press the I PLAY STILL button m Keep pressing 44 gt gt REW FF buttons during playback or still mode To resume normal playback release the button PHOTO O O Slow Playback Forward Reverse SC D354 D355 only Forward Slow playback Press the SLOW button on the remote control during playback To resume normal playback press the II PLAY STILL button m Reverse Slow Playback Press the lt ll button during forward slow play back To resume forward slow playback press the l gt button To resume normal playback press the II PLAY STILL button lt SC D354 D355 only gt Playback Frame Advance To play back frame by frame SC D354 D355 only m Press the F ADV button on the remote control while in still mode r Video sequence advances frame by frame each time you press the F ADV button EE The F ADV function works in still mode only QQ anue Q
18. Mark Quick menu is used to access Camcorder functions by simply using the Menu selector Quick menu provides easier access to the frequently used menus without using the MENU button It can be set on the selected file only se 2 46 1 Press the Menu selector 800x600 2 Move the Menu selector to left or right to select Print Mark then press the Menu selector TEREN Delete 3 Move the Menu selector to the left or right to select the quantity then press the Menu selector esi I Exit 100 0002 4 To exit press the MENU button 3 a 2 46 800x600 Notes Ifthe Print Mark is set to This File you can set the number of copies from 0 to 999 WPlay Select m f the Print Mark is set to All Files you can set the number of copies to 0 or 1 Pelee __ The All Files option may require extended operation time depending on the number of stored images PAniMa E 002 DPOF supporting printers are commercially available EI exit 100 0002 m Use the USB cable provided with the Camcorder m 2460 800x600 A amp 002 100 0002 A Fon PictBridge SC D353 D354 D355 only Printing Your Pictures Using the PictBridge PictBridge function works only in M Player mode By connecting the Camcorder to printers with PictBridge support sold separately you can send images from the Memory card directly to the printer with a few simple operations With the PictBridge Support yo
19. Memory then press the Menu selector Move the Menu selector to the left or right to select Format then press the Menu selector Move the Menu selector to the left or right to select desired option Int Memory or Memory card then press the Menu selector SC D354 D355 only f you select Int Memory or Memory card a message All files are deleted Do you want to format appears 7 Move the Menu selector to the left or right to select Yes then press the Menu selector Complete appears when the format is completed 8 To exit press the MENU button oA on Notes m f you execute the Format function all still inages motion clips will be erased completely and erased still images motion clips cannot be recovered Formatting the Memory card using a different device will cause Memory card read errors Formatting the Memory card deletes all the stored data in the Memory card Do not turn the power off in the middle of the formatting A Memory Stick with the protection tab set to save will not be formatted see page 87 Do not format the Memory Card on a PC Not Formatted message may appear if a Memory Card formatted on a PC was inserted M Player Mode M Play Select Delete Delete All Protect gt of Print Mark Format Photo M Play Select Delete Delete All Protect Print Mark Move Select GQ Exit 2 46 800x600 All files are deleted Do you
20. Out Gradual disappearance Approx 4 seconds b Fade In Approx 4 seconds Gradual appearance b Fade In Release the FADE button a Basic Recording Using Back Light Compensation Mode BLC BLC works in both Camera and M Cam modes Back lighting exists when the subject is darker than the background The subject is in front of a window The person to be recorded is wearing white or shiny clothes and is placed against a bright background the person s face is too dark to distinguish his her features The subject is outdoors and the background is overcast The light sources are too bright lt BLC off gt lt BLC on gt The subject is against a snowy background 1 Set the Power switch to CAMERA 2 Set the Mode switch to TAPE or MEMORY CARD SC D353 D354 D355 only 3 Press the BLC button m BLC icon ge will be displayed 4 To exit BLC mode press the BLC button again 4 om sia Ja m Each press of the BLC button toggles Normal gt BLC gt Normal 60min Notes amp m When NITE PIX to set to ON the BLC function does not work SC D352 D354 D355 only m The BLC function will not operate in EASY Q mode Basic Recording Using the Color Nite Shutter COLOR NITE SHUTTER function works only in Camera mode Shutter speed can be controlled allowing you to record slow moving objects COLOR NITE SHUTTER function may produce a brighter image
21. S m 2 46 800x600 100 0002 i 2 La Digital Still Camera Mode SC D353 D354 D355 only Using Quick Menu Protect Quick menu is used to access Camcorder functions by simply using the Menu selector Quick menu provides easier access to the frequently used menus without using the MENU button Press the Menu selector a D Move the Menu selector to left or right to select Protect then press the Menu selector 3 Move the Menu selector to the left or right to select Off or On then press the Menu selector NS To exit press the MENU button a 2 46 800x600 Mpap Saec Photo Delete Protect Print Mark I Exit 100 0002 2 46 800x600 M Play Select Delete rN Protect On Print Mark hi Exit 100 0002 mm 2 460 800x600 A 100 0002 Digital Still Camera Mode SC D353 D354 D355 only Deleting Still Images and Moving Images The Delete function works only in M Player mode You can erase the still images and moving images recorded on the Memory card If you want to delete protected images you must first deactivate the image protection An image which has been deleted cannot be recovered se ge go op M Player Mode 1 Set the Power switch to PLAYER MpPlay Select Delete Delete All Protect gt ot Print Mark Format Photo 2 Set the Mode switch to MEMORY CARD 3 Using the lt 44 gt gt REV FWD buttons search for the s
22. S e 1 Lithium battery cover tii 2 Charging indicator 5 Tripod receptacle Lithium battery cover Charging indicator Memory card slot SC D353 D354 D355 only Memory Stick Battery release Memory Stick e a Memory Stick PRO Tripod receptacle p mmea Memory Stick PRO Memory Card Slot Usable Memory Card SC D353 D354 only SC D355 only 1 2 3 4 5 SD MMC Getting to Know Your Camcorder Remote Control SC D354 D355 only 1 PHOTO 18 DISPLAY 2 START STOP 3 SELF TIMER 4 ZERO MEMORY 5 PHOTO SEARCH 17 Zoom EE 16 X2 7 gt gt FF 15 DATE TIME 8 44 REW 14 I gt SLOW 9 PLAY 13 H STILL 12 W STOP 10 Direction 11 F ADV 1 PHOTO see page 68 10 Direction lt I gt see page 73 2 START STOP 11 F ADV see page 74 3 SELF TIMER see page 43 12 m STOP 4 ZERO MEMORY see page 42 13 1I STILL 5 PHOTO SEARCH 14 I gt SLOW 6 A DUB see page 77 15 DATE TIME 7 gt gt FF 16 X2 see page 74 8 lt lt REW 17 Zoom 9 b gt PLAY 18 DISPLAY Preparation Adjusting the Hand Strap It is very important to ensure that the Hand strap has been correctly adjusted before you begin your recording The Hand strap enables you to Hold the Camcorder in a stable comfortable position Press the ZOOM and Start Stop button without having to change the posit
23. Set the Power switch to PLAYER Set the Mode switch to TAPE SC D353 D354 D355 only Press the PB ZOOM button in playback mode or in still mode The image is magnified starting from the center of image You can zoom in from 1 2x to 8 0x by moving the Zoom lever Zoom ratio is not displayed on the screen To cancel the playback Zoom function press the PB ZOOM or m STOP button Notes The PB ZOOM function enlarges the center of the screen only You cannot apply the Playback Zoom function to pictures which are being input from an external video source The Playback Zoom image cannot be imported to your PC from the Camcorder s DV jack The PB ZOOM images cannot be exported to a PC OSD will not be displayed on the LCD screen while the PB ZOOM function is being operated To display OSD press the PB ZOOM button once to stop operating PB ZOOM function or press the mi STOP button to stop playback Playback AV In Out SC D355 only AV In Out function works only in Player mode AV in out setting enables you to record signal from external sources and display it on LCD screen Also you can direct your video or image to external devices to record or play back Connect the Camcorder to your VCR or TV with the Audio Video cable See pages 71 72 Set the Mode switch to TAPE Set the Power switch to PLAYER Turn on the VCR or TV Insert the blank tape with protection tab closed into the Camcorder f
24. Tel 1 800 SAMSUNG 1 800 726 7864 Samsung Electronics Internet Home Page http Avww samsung com AD68 00839B
25. To resume normal playback press the I PLAY STILL button OO cq Forward frame advance Press the F ADV button on the remote control in still mode 6 Ole ZERO DATED 5 re TIME Reverse frame advance Press the lt I button on the remote control to change the direction in FADV mode Press the F ADV button on the remote control om X2 Playback Forward Reverse SC D354 D355 only Forward X2 playback X J Press the X2 button on the remote control during playback mer Ras ND355 ane To resume normal playback press the H PLAY STILL button Reverse X2 playback Press the lt li button during forward X2 playback To resume normal playback press the II PLAY STILL button Reverse Playback SC D354 D355 only To playback in reverse at normal speed press the lt lll button during normal forward playback Press the II PLAY STILL or I gt button to return to normal forward playback Notes m Mosaic shaped distortion may appear on the screen while in some of the various playback modes Mosaic shaped distortion or noise may be experienced when you play back tapes recorded in LP which contain various playback functions m Sound will only be heard during normal SP or LP playback a Playback Zooming during Playback PB ZOOM 1 The Playback Zoom function works in Player mode The Playback Zoom function enables you to magnify the playback or still image
26. White Balance Program AE Digital Effect and BLC If focusing is difficult in the auto focus mode when using the Nite Pix function focus manually Do not cover the Infrared Light with your hand Do not set the NITE PIX to ON in bright lighting It might damage the CCD Charge Coupled Device sTBY gt Nite Pix 0 00 10 fi 60min Basic Recording Power Nite Pix SC D352 D354 D355 only The Power Nite Pix function works only in Camera mode The Power Nite Pix function can record a subject more brightly in darkness than the Nite Pix function When you work in Power Nite Pix mode the Power Nite Pix icon remains on the LCD screen Power Nite Pix is not available while taking a photo image or with EASY Q is in use 1 Set the Power switch to CAMERA 2 Set the Mode switch to TAPE SC D354 D355 only 3 Turn on the NITE PIX switch and then press the COLOR NITE LED LIGHT button 4 Press the COLOR NITE LED LIGHT button to set shutter speed When using Power Nite Pix the image takes on a slow motion like effect The slow shutter function enables you to record a subject more brightly 5 Each time you press the COLOR NITE LED LIGHT button the shutter speed changes to Color N 1 30 Color N 1 15 Color N 1 15 G and off in order 6 To cancel the Power Nite Pix function press the COLOR NITE LED LIGHT button to set to off and then turn off the NITE PIX switch Notes
27. are not available while EASY Q or NITE PIX is in use m Once DIS EASY Q or COLOR NITE SHUTTER is set 16 9 Wide Emboss2 Pastel2 Mirror or SiS Camera Mode Mosaic modes will be released Program AE Off m Digital Zoom is not available in the 16 9 Wide Emboss2 Pastel2 Mirror or Mosaic modes White Balance Zn Digital Effect modes other than 16 9 Wide Emboss2 Pastel2 Mirror or Mosaic are available while Eita E DIS is in use Digital Zoom CAA m Setting the NITE PIX while Digital Effect is in use releases the Digital Effect and releasing the Minor NITE PIX will set the Digital Effect to Off mode iil stl m Photo image recording is not available in the 16 9 Wide mode Advanced Recording Zooming In and Out with Digital Zoom Zoom works only in Camera mode Selecting the Digital Zoom Ca ka on T Notes Set the Power switch to CAMERA 2 Set the Mode switch to TAPE SC D353 D354 D355 only Press the MENU button Move the Menu selector to the left or right to select Camera then press the Menu selector Move the Menu selector to the left or right to select Digital Zoom then press the Menu Zooming more than 20x is achieved digitally up to 900x when combined with optical zoom The picture quality may deteriorate depending on how much you zoom in on the subject We recommend that you use the DIS feature with Digital Zoom for picture stability see page 61
28. cannot be recharged Use another Battery pack When you see a blue screen during playback The video heads may be dirty Clean the head with a cleaning tape A vertical strip appears on the screen when recording a dark background The contrast between the subject and the background is too great for the Camcorder to operate normally Make the background bright to reduce the contrast or use the BLC function while you are recording in bright Surroundings The image in the Viewfinder is blurred The Viewfinder lens has not been adjusted Adjust the Viewfinder control lever until the indicators displayed on the Viewfinder come into sharp focus Auto focus does not work Check the Manual Focus menu Auto focus does not work in the Manual Focus mode Play FF or REW button does not work Check the Power switch Set the Power switch to PLAYER You have reached the beginning or end of the cassette When you see a mosaic pattern during playback search This is normal operation and it is not a failure or defect The tape may be damaged Replace the tape Cleaning the video heads see page 113 Specifications Model Name SC D351 D352 D353 D354 D355 System Video signal Video recording system Audio recording system Usable cassette NTSC 2 rotary heads Helical scanning system Rotary heads PCM system Digital video tape 6 35mm width Mini DV cassette Tape
29. few seconds Taking another picture within this interval is not possible The indicator appears LCD screen during the time it takes to save the image Notes m Still images are saved in the Memory card in an 800x600 format The number of still images that can be stored depends on the quality of the image Digital Still Camera Mode SC D353 D354 D355 only Viewing Still Images This function works only in M Player mode You can playback and view still images recorded on the Memory card Be sure that the M Play Select is set to Photo in the Menu There are 3 ways to view recorded images Single To view an image frame by frame Slide show To view all images automatically and in consecutive order Multi display To view 6 images at once To view a Single Image 1 Set the Power switch to PLAYER 2 Set the Mode switch to MEMORY CARD The last recorded image appears f there are no recorded images on the Memory card No image will display on ans res the screen FWD S SHOW MULTI DISP 3 Using the lt 44 gt gt REV FWD buttons search for the desired still image To view the next image press the gt FWD button To view the previous image press the 44 REV button Pressing gt FWD when you are on the last image will take you to the first image and pressing lt 44 REV when you are on the first image will take you to the last image Keep pressing gt FWD or 44 REV
30. m PictBridge supporting printers are commercially available Use the USB cable provided with the Camcorder m Use the AC power adapter for your Camcorder during PictBridge Direct Printing Turning your Camcorder off during the printing might damage data on the Memory card Printing still images is supported Motion clips are not available for printing You can set various printing options depending on the printer Please refer to the user s manual of the printer Date Time ENGLISH Maintenance After Finishing a Recording At the end of a recording you must remove the power source When recording with a Lithium ion Battery pack leaving the pack on the Camcorder can reduce the life span of the battery The Battery pack should be release after recording is completed 1 Slide the TAPE EJECT switch in the direction of the arrow m Opening the cassette door ejects the tape automatically Please wait while the tape is completely ejected 2 After removing the tape close the door and store the Camcorder in a dust free environment Dust and other foreign materials can cause square shaped noise or jerky images 3 Set the Power switch to the Off 4 Disconnect the power source or remove the lithium ion Battery pack Press the BATTERY RELEASE button located on the bottom of the Camcorder and slide the Battery pack in the direction of the arrow ENGLISH Maintenance Cleaning
31. speed SP approx 18 81mm s LP approx 12 56mm s Tape recording time SP 60 minutes when using DVM 60 LP 90 minutes when using DVM 60 FF REW time Approx 150 sec using DVME60 tape Image device CCD Charge Coupled Device 680k pixels Lens F1 6 20x Optical 900x Digital Electronic zoom lens Filter diameter 930 LCD screen Viewfinder Size dot number 2 36inchs 112k LCD screen Method TFT LCD Viewfinder B W LCD SC D351 D352 D353 D354 only Color LCD SC D355 only Connectors Video output 1Vp p 750 terminated S video output Y 1Vp p 75Q C 0 286Vp p 750 Audio output 7 5dBs 6000 terminated DV input output 4pin special in out connector USB output Mini B type connector External mic 3 5 stereo General Power source Power source type Power consumption Recording Operating temperature Storage temperature External dimension Weight Internal MIC Remote control SC D354 D355 only DC 8 4V Lithium lon Battery Pack 7 4V Lithium lon Battery Pack Power supply 100V 240V 50 60Hz 4 3W LCD 4 0W Viewfinder 0 40 C 32 F 104 F 20 C 60 C 4 F 140 F Height 3 62inches 92mm Length 4 63inches 117 5mm Width 2 52inches 64mm 0 904lb 410g 14 460z Except for Lithium lon Battery Pack and tape Omni directional stereo microphone Indoors greater than 49ft 15m straight line Outdoors about 16 4ft 5m straight line f These technical specifications and design may be changed w
32. the Built in Memory SC D354 D355 only a Using Quick Menu Memory Type frase cova teria cnet ARREA EEEREN CNE NEREK ARENO ER GR RERA atten nec ttrstd 90 A Contents Selecting the Image Quality Select the Image Quality Number of Images on the Memory Card Using Quick Menu Photo Quality Memory File Number Taking Photos Viewing Still Images To view a Single Image To view a Slide Show To view the Multi Display Protection from accidental Erasure Using Quick Menu Protect Deleting Still Images and Moving Images Using Quick Menu Delete Formatting the Memory Card MPEG Recording Saving Moving Picture Files onto a Memory Card MPEG Playback simsan Using Quick Menu M Play Select Recording an Image from a Cassette as a Still Image Copying Still Images from a Cassette to Memory Card Copy to Copies Files from the Memory Card to the Built in Memory SC D354 D355 only Marking Images for Printing Using Quick Menu Print Mark PictBridge SG D353 D3Z54 D SSD OMY ereere e ee e LO MamntenaNC e neen e A AE AE E ae L2 After Finishing a Recording Cleaning and Maintaining the Camcorder Using Your Camcorder Abroad Troubleshooting we 115 IS DOGHIT CATIONS a ELS a LUD Warranty SEA users Only cscsstecortectssescssrsrtecesterserectesestee nes srases sees 20 A
33. the Menu selector to the left or right to select Audio Select then press the Menu selector 6 Move the Menu selector to the left or right to select the audio playback channel then press the Menu selector Sound 1 play the original sound Sound 2 play the dubbed sound MIX 1 2 play back sound and 2 equality mixed 7 To exit press the MENU button 8 Press the II PLAY STILL button to playback the dubbed tape Note When you playback added sound Sound 2 or MIX mode you may experience a loss of sound quality Player Mode _ Photo Search f Photo Copy lt J Audio Select gt Sound 1 Move Select GQ Exit S Player Mode Photo Search Photo Copy Audio Select wv Sound 1 Sound 2 MIX 1 2 Move Select DEY Exit gt 0 01 53 10 dd Sound 2 f 20min IEEE 1394 Data Transfer Transferring IEEE1394 i LINK DV Standard Data Connections Connecting to a DV Device DVD Recorder Camcorder etc m Connecting to other DV standard products A standard DV connection is quite simple If a product has a DV port you can transfer data by connecting to the DV port using the correct cable Il Please be careful since there are two types of DV ports 4pin 6pin This Camcorder has a 4pin terminal With a digital connection video and audio signals are transmitted in digital format allowing high quality images to be transferred Connecting to a PC
34. want to format Red No 100 0002 A Fon Digital Still Camera Mode SC D353 D354 D355 only MPEG Recording Saving Moving Picture Files onto a Memory Card 1 2 3 4 5 N A Wiss If it is not in the Camcorder insert it into the slot Sia AA Set the Power switch to CAMERA Press the Start Stop button the images are recorded on the Memory card in MPEG4 otes You can record moving picture images with audio on the Memory card The screen format of the moving picture to be recorded is 720x480 Check whether Memory card is inserted into the Camcorder 4 Set the Mode switch to MEMORY CARD PLAYER You can record a Camcorder still image on Memory card by pressing the PHOTO button instead of the Start Stop button Press the Start Stop button to stop the recording MENU button and Menu selector are not available while MPEG recording To use MENU button and Menu selector stop recording MPEG recording is not available when a menu or Quick menu is displayed on the screen To start recording press the MENU button to make it disappear Before using the MPEG REC function check whether the Memory card is inserted into the Camcorder Moving images that you recorded are saved in avi avi 1 0 file format on the Memory card The files that you recorded are saved in a following folder see illustration low right hand corner
35. you want to record from a connected VCR insert a recorded VHS tape into the VCR Press the MENU button The menu list will appear 7 Move the Menu selector to the left or right to select Record then press the Menu selector 8 Move the Menu selector to the left or right to select AV In Out then press the Menu selector 9 Move the Menu selector to the left or right to select In then press the Menu selector f you want to see the Camcorder picture with a TV set AV In Out menu to Out 10 To exit press the MENU button 11 Press the Start Stop button to set the Camcorder to REC PAUSE mode PAUSE appears on the LCD screen 12 Select the TV program or playback the VHS tape a 13 Press the Start Stop button to start recording f you want to pause recording for a while press the Start Stop button again 14 To stop recording press the W STOP button akON gt D Rec Mode gt SP Audio Mode gt 12Bit Wind Cut Off AVO Pout Note Nove B Seect DEY Exit When you record the images being played back on an analog VCR if they are not being played back at normal speed for example more than double speed or slow playback only a gray image appears on the Camcorder reN Playback Audio Dubbing SC D354 D355 only The Audio Dubbing function works only in Player Mode You can not dub sound on a pre recorded tape in LP or 16 bit mode You can add sound to the original sou
36. 1 Select EE Exit 7 _ Photo Search Ea Search S lt lt gt gt Bq 0 41 56 10 25min Cancel GE Bt _ Photo Search gt 0 44 38 03 25min Photo ne Ea Search Cancel GE ar Playback Playing Back a Tape You have recorded on the LCD Screen The playback function works only in Player mode You can monitor the playback picture on the LCD screen 1 Set the Power switch to PLAYER 2 Set the Mode switch to TAPE SC D353 D354 D355 only 3 Insert the tape you wish to view See page 36 4 Open the LCD screen Adjust the angle of the LCD screen and set the brightness or color if necessary 5 Press the lt 4 REW button to rewind the tape to the starting point To stop rewinding press the W STOP button The Camcorder stops automatically after rewinding is complete 6 Press the gt II PLAY STILL button to start playback You can view the picture you recorded on the LCD screen To stop the play operation press the W STOP button Adjusting the LCD Bright Color during Playback You can adjust the LCD Bright Color during playback The adjustment method is the same procedure as used in Camera mode See page 32 Notes m You can also view the picture on a TV screen after connecting the Camcorder to a TV or VCR see page 71 72 Various functions are available in Player mode see page 73 For searching and vi
37. 1 800 726 7864 Labor 90 days carry in Parts 1 year On carry in models transportation to and from the service center is the customer s responsibility The original dated sales receipt must be retained by the customer and is the only acceptable proof of purchase It must be presented to the authorized service center EXCLUSIONS WHAT IS NOT COVERED This warranty does not cover damage due to accident fire flood and or other acts of God misuse incorrect line voltage improper installation improper or unauthorized repairs commercial use or damage that occurs in shipping Exterior and interior finish lamps and glass are not covered under this warranty Customer adjustments which are explained in the instruction manual are not covered under the terms of this warranty This warranty will automatically be voided for any unit found with a missing or altered serial number This warranty is valid only on products purchased in the United States and Puerto Rico Some States do not allow the exclusions or limitations of incidental or consequential damages or allow limitations on how long an implied warranty lasts so the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from State to State ENGLISH Memo ENGLISH Memo ENGLISH Memo THIS CAMCORDER IS MANUFACTURED BY SERVICE DIVISION 400 Valley Road Suite 201 Mt Arlington N J 07856
38. AMCORDER has been dropped or the cabinet has been damaged f When the CAMCORDER exhibits a distinct change in performance this indicates a need for service REPLACEMENT PARTS When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer and having the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards SAFETY CHECK Upon completion of any service or repairs to this CAMCORDER ask the service technician to perform safety checks to determine that the CAMCORDER is in safe operating order Notices and Safety Instructions 22 To prevent damage which may result in fire or shock hazard do not expose this appliance to rain or moisture 23 If this power supply is used at 240V ac a suitable plug adapter should be used NOTE TO CATV SYSTEM INSTALLER This reminder is provided to call the CATV system installer s attention to Article 820 40 of the NEC that provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical USER INSTALLER CAUTION Your authority to operate this FCC certified equipment could be voided if you make changes or modifications not expressly approved by this party responsible for compliance to part 15 FCC rules NOTE LAMP S INSIDE THIS P
39. Approx 74 Approx 148 File No The actual number of images that you can record varies depending on the nature of the subject to be recorded Move Select DEY Exit Notes XN A The above approximation is based on a 8MB Memory Stick under normal recording conditions The number of pictures that can be stored on a memory card depends on various conditions A Digital Still Camera Mode SC D353 D354 D355 only Using Quick Menu Photo Quality Quick menu is used to access Camcorder functions by using the Menu selector Quick menu provides easier access to frequently used menus without using the MENU button 1 Press the Menu selector 2 Move the Menu selector to left or right to select Photo Quality then press the Menu selector 3 Move the Menu selector to the left or right to select desired image quality Super Fine Fine Normal then press the Menu selector 4 To exit press the MENU button 46 O timin White Balance Auto Photo Quality Exposure Manual Focus S Exit 46 O 1min White Balance a Photo Quality Super Fine g Exposure Y Manual Focus Exit Digital Still Camera Mode SC D353 D354 D355 only Memory File Number Set the Mode switch to MEMORY CARD File number setting works only in M Cam mode File numbers are given to images in the order they were recorded when they are stored on the Memory card Memory fil
40. Bit recording mode Audio dubbing is not possible when using this mode 1 Set the Power switch to CAMERA or PLAYER Camera Mode J Rec Mode gt SP amp Audio Mode 1 2Bit Wind Cut Off 2 Set the Mode switch to TAPE SC D353 D354 D355 only 3 Press the MENU button The menu list will appear W Move K Select ma 4 Move the Menu selector to the left or right to select Record then press the Menu selector Camera Mode 5 Move the Menu selector to the left or right to select Audio Mode then press Pay Rec Mode the Menu selector Audio Mode v12Bit Wind Cut 16Bit 6 Move the Menu selector to the left or right to select desired audio mode 12Bit or 16Bit then press the Menu selector ioe sen Ee 7 To exit press the MENU button F m sTBY 0010 f 60min 16Bit Note When 12Bit is selected no 12Bit indication will be displayed on the screen A Advanced Recording Cutting Off Wind Noise Wind Cut The Wind Cut function works in both Camera and Player Audio dubbing modes Use the Wind Cut when recording in windy places such as the beach or near buildings The Wind Cut function minimizes wind noise or other noise while recording When the wind cut is on some low pitched tones are eliminated along with the sound of the wind 1 Set the Power switch to CAMERA or PLAYER Camera Mode 2 Set the Mode switch to TAPE
41. D355 only Press the MENU button The menu list will appear Move the Menu selector to the left or right to select Tape then press the Menu selector Move the Menu selector to the left or right to select Photo Search then press the Menu selector Press the lt 4 gt REW FF buttons to select the photo The photo search process appears on LCD screen while you are searching After completing the search the Camcorder displays the still image 7 To exit press the W STOP or MENU button D AF WN Notes Pressing the PHOTO button while recording stops the recording and saves the still image captured at that moment It takes approx 6 7 seconds to save the image and then recording resumes m You can use the remote control to take a photo by using the PHOTO button on the remote control Pressing the PHOTO button on the remote control records the still image at once with automatic focusing SC D354 D355 only When there are no still images recorded on the tape it will be fully rewound or forwarded m Taking a photo image is not available while COLOR NITE SHUTTER or 16 9 Wide is in use DIS Digital Zoom COLOR NITE SHUTTER Digital Effect and Nite Pix are not available when take a photo image Taking a photo image while EASY Q DIS or Digital Zoom mode is in use will the mode i After a photo image is taken the mode will return automatically Move Photo Search Photo Copy Audio Select Sound
42. Digital Video Camcorder viy SC D351 D352 D353 D354 D355 AF Auto Focus CCD charge Coupled Device LCD Liquid Crystal Display Owner s Instruction Book Before operating the unit please read this Instruction Book thoroughly and retain it for future reference US PATENT 4415844 Notices and Safety Instructions Safety Instructions CAUTION RISK OF ELECTRIC HOCK Al AS DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL To prevent electric shock match wide blade of plug to wide slot and fully insert 1 READ INSTRUCTIONS _ All the safety and operating instructions should be read before the CAMCORDER is operated RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference HEED WARNINGS All warnings on the CAMCORDER and in the operating instructions should be adhered to FOLLOW INSTRUCTIONS All operating and maintenance instructions should be followed CLEANING Unplug this CAMCORDER from the wall outlet before cleaning Do not use liquid or aerosol cleaners Use a dry cloth used for dusting cabinets ATTACHMENTS Do not use attachments not recommended by the CAMCORDER product manufacturer as they may be hazardous 7 WATER AND MOISTURE This symbol is intended to alert the user to the presence of uninsulat
43. Eject the tape ae fault 2 Set to OFF 3 Detach the battery 4 Reattach the battery If unresolved contact your local samsung service center moisture condensation has formed in the Camcorder see below Moisture Condensation If the Camcorder is brought directly from a cold place to a warm place moisture may condense inside the Camcorder on the surface of the tape or on the lens In this condition the tape may stick to the head drum and be damaged or the unit may not operate correctly To prevent possible damage under these circumstances the Camcorder is fitted with a moisture sensor If there is moisture inside the Camcorder E amp DEW is displayed If this happens none of the functions except cassette ejection will work Open the cassette compartment and remove the battery Leave the Camcorder for at least two hours in a dry warm room Troubleshooting Self Diagnosis Display in M Cam M Player Modes SC D353 D354 D355 only Display Blinking Informs that Action No Memory Card slow There is no Memory card in he Camcorder Insert a Memory card Memory Full slow There is not enough memory to record Change to a new Memory card Erase recorded image No image slow There are no images recorded on the Memory card Record new images Write protect The Memory card is record protected Release the write protect tab on the Memory card
44. IDE SHOW STOP BLC MULTI DISP Getting to Know Your Camcorder Left Side View 1 DISPLAY 5 Focus adjustment knob 6 Viewfinder 2 MACRO PB ZOOM Le in 3 Speaker SC D351 D353 4 Mode switch mu only SC D353 D354 D355 only i 7 COLOR NITE LED LIGHT wees SC D352 D354 D355 only 1 DISPLAY see page 25 6 Viewfinder 2 MACRO PB ZOOM see page 44 see page 75 7 COLOR NITE SHUTTER see page 47 3 Speaker SC D351 D353 only 7 COLOR NITE LED LIGHT see page 48 4 Mode switch MEMORY CARD TAPE SC D353 D354 D355 only SC D352 D354 D355 only 5 Focus adjustment knob Getting to Know Your Camcorder Right amp Top View 1 NITE PIX switch SC D352 D354 D355 only 7 TAPE EJECT 2 Menu selector VOL MF 8 Zoomi lever IEEE1394 3 MENU button 9 PHOTO button USB 10 Jacks gt SC D352 D353 D354 D355 only 4 Start Stop button 11 Hand strap hook 5 Power switch 12 Jack cover AN 6 DC jack 13 Cassette door External MIC 1 NITE PIX switch 8 Zoom lever SC D352 D354 D355 only 9 PHOTO button 2 Menu selector VOL MF see page 68 3 MENU button 10 Jacks 4 Start Stop button 11 Hand strap hook 5 Power switch CAMERA or PLAYER 12 Jack cover 6 DC jack 13 Cassette door 7 TAPE EJECT Getting to Know Your Camcorder Rear amp Bottom View 3 Memory card slot SC D353 D354 D355 4 Battery release only e o o
45. NU button Player Mode La Gu Clock Set E Beep Sound gt on J Shutter Sound _ gt On USB Version USB 2 0 Language English Ei Move K sSeect DEY Exit J S Player Mode l Clock Set F Beep Sound O Shutter Sound Off USB Version vOn 2 Language a Move K Select ma System Menu Setting Viewing the Demonstration Before you begin Make Sure that there is no tape inserted in the Camcorder see page 36 Demonstration automatically shows you the major functions that are included with your Camcorder so that you may use them more easily The Demonstration function may only be used in the Camera mode without a tape inserted in the Camcorder The Demonstration operates repeatedly until the Demonstration mode switched Off 1 Set the Power switch to CAMERA Camera Mode gt System Clock Set Beep Sound gt On Language English Demonstration gt On 2 Set the Mode switch to TAPE SC D353 D354 D355 only 3 Press the MENU button a The menu list will appear 4 Move the Menu selector to the left or right to select System then press the Menu selector voe msa ee S 5 Move the Menu selector to the left or right to select Demonstration then press the a Menu selector Camera Mode Clock Set Beep Sound 6 Move the Menu selector to the left or right to select On then press the MENU button
46. RODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL STATE OR FEDERAL LAWS For details see lamprecycle org eiae org or call 1 800 Samsung NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help and for additional suggestions The user may find the following booklet prepared by the Federal Communications Commission helpful How to Identify and Resolve Radio TV Interference Problems This Booklet is available fro
47. SC D353 D354 D355 only If you want to use this unit as a Camcorder set the Mode switch to TAPE If you want to use this unit as a DSC Digital Still Camera Set the Mode switch to MEMORY CARD lt CAMERA mode gt lt PLAYER mode gt MEMORY CARD A Preparation Using the Lithium lon Battery Pack The amount of continuous recording time available depends on The type and capacity of the Battery pack you are using How often the zoom function is used It is recommended that you have several batteries available Charging the Lithium lon Battery Pack 1 Attach the Battery pack to the Camcorder 2 Connect the AC Power adapter to an AC Cord and connect the AC Cord to a wall socket 3 Connect the DC cable to the DC jack socket on the Camcorder 4 Turn the Power switch to Off and the charging indicator will start to flash showing that the battery is charging Blinking time Charging rate Once per second Less than 50 Twice per second 50 75 Three times per second 75 90 Blinking stops and stays on 90 100 On for a second and Error Reset the Battery pack and off for a second the DC cable 5 When the battery is fully charged disconnect the Battery pack and the AC Power adapter from the Camcorder Even with the Power switched Off the Battery pack will still discharge lt Charging indicator gt Notes m The Battery pack may be charged a little at the time of p
48. SC D353 D354 D355 only Press the MENU button The menu list will appear Move the Menu selector to the left or right to select System then press the Menu selector Move the Menu selector to the left or right to select Clock Set then press the Menu selector The year will highlight first Move the Menu selector to the left or right to set current Year then press the Menu selector The month will be highlighted You can set the month day hour and minute following the same procedure for setting the year Press the Menu selector after setting the minutes m The message Complete will be displayed To adjust the clock select the Year Month Day Hour or Min by pressing the Menu selector then move the Menu selector to the left or right to set respective values 9 To exit press the MENU button Notes After the Lithium battery loses its charge after about 6 months the date time appears on the screen as 12 00 AM JAN 1 2005 You can set the year up to 2037 If the Lithium battery is not installed any input data will not be backed up Camera Mode Clock Set Language Beep Sound Demonstration gt On English gt On Move Select EMU Exit J Camera Mode Language Y Beep Sound Demonstration JANEE 2005 12 00 AM Move jSelect DEY Exit S Camera Mode t Back Clock Set Language Beep Sound Demonstration Complet
49. SC D353 D354 D355 only Ca RecMode psp amp Audio Mode 1 2Bit Wind Cut Off 3 Press the MENU button m 4 Move the Menu selector to the left or right to select Record then press the Menu selector Wivove KSeect EEN Ext 5 Move the Menu selector to the left or right to select Wind Cut then press the Menu selector Rec Mode Audio Mode 6 To activate the Wind Cut function move the Menu selector to the left or right to select On then press the Menu selector 7 To exit press the MENU button Nove isee GEM Exit Wind Cut F1 icon will be displayed on the LCD screen when you turn the Wind Cut On ra i STBY 0 00 10 f 60min Note Make sure Wind Cut is set to off when you want the microphone to be as sensitive as possible RA amp Advanced Recording Setting the Shutter Speed amp Exposure You can set Shutter Speed only in Camera mode The Exposure function works in both Camera and M Cam modes Quick menu is used to access Camcorder functions by simply using the Menu selector cm STBY ooo 1 Set the Power switch to CAMERA 60min 2 Set the Mode switch to TAPE SC D353 D354 D355 only eee 3 Press the Menu selector Ute Balance Quick menu list will appear Exposure 4 Move the Menu selector to the left or right to select Shutter or Exposure then press the _ Menu selector oe J 5 Move the Menu selector to the left or right to select Manual then press the Men
50. TON Bak I y gt gt 0 44 38 03 E 25min Ne g 2 46 f 25min Photo Copy rll Now copying BY a Back Exit Digital Still Camera Mode SC D353 D354 D355 only Copy to Copies Files from the Memory Card to the Built in Memory SC D354 D355 only The Copy To function works only in M Player mode You can copy selected or all images stored in the Memory card to the built in memory Set the Power switch to PLAYER Set the Mode switch to MEMORY CARD Press the MENU button The menu list will appear Move the Menu selector to the left or right to select Memory then press the Menu selector Move the Menu selector to the left or right to select Copy to then press the Menu selector Move the Menu selector to the left or right to select options Back This File or All Files then press Menu selector To go back to the previous mode select Back f This File or All Files is selected Now copying is displayed on the screen and copying starts To exit press the MENU button Memory Type M Play Select Pint Memory Photo Off C A NMove K Select ma v Back This File All Files Digital Still Camera Mode SC D353 D354 D355 only Marking Images for Printing This Camcorder supports the DPOF Digital Print Order Format print format You can automatically print images recorded on a Me
51. The Lithium battery for the Camcorder lasts about 6 months under normal operation from the time of installation When the Lithium battery becomes weak or dead the date time indicator will display 12 00 AM JAN 1 2005 when you set the Date Time to on When this occurs replace the Lithium battery with CR2025 type terminal face up You need to insert or replace the Lithium battery when You purchase the Camcorder The remote control doesn t work Position the Lithium battery in the Lithium battery holder with the positive terminal face up Be careful not to reverse the polarity of the battery Should any battery be swallowed consult a doctor immediately Preparation Connecting a Power Source There are two types of power source that can be connected to your Camcorder The AC Power adapter and AC Cord used for indoor recording The Battery pack used for outdoor recording To use the AC Power Adapter and DC Cable 1 Connect the AC Power adapter to the AC Cord 2 Connect the AC Cord to a wall socket Notes m You must use an AA E8 TYPE AC Power adapter The plug and wall socket type may differ according to your resident country 3 Connect the DC cable to the DC jack socket of the Camcorder 4 Set the Camcorder to each mode by holding down the tab on the Power switch and turning it to the CAMERA or PLAYER mode To Select the Camcorder Mode
52. The menu list will appear selector Move the Menu selector to the left or right to select desired zoom mode Off 100x 200x 400x or 900x then press the Menu selector To exit press the MENU button Camera Mode _ Program AE Auto White Balance _ Auto Digital Effect Off DIS gt Off Digital Zoom Off Maximum zooming may result in lower picture quality Bove seet E j Digital Zoom is not available while DIS EASY Q taking a photo image COLOR NITE SHUTTER 16 9 Wide Emboss2 Pastel2 Mirror or Mosaic is in use s es Camera Mode Once taking a photo image COLOR NITE SHUTTER 16 9 Wide Emboss2 Pastel2 Mirror or t Back Mosaic is set Digital Zoom mode will be released The Digital Zoom mode will be backed up EAE WN Once DIS or EASY Q is set Digital Zoom mode will be released Digital Etfect KOA DIS 200x Digital Zoom 400x 900x C W nNMove Seet DEY Exit J La Advanced Recording Photo Image Recording Photo image recording works only in Camera mode Set the Power switch to CAMERA Set the Mode switch to TAPE SC D353 D354 D355 only Press the PHOTO button The still picture is recorded for about 6 7 seconds After the PHOTO has been recorded the Camcorder returns to its previous mode A gt N gt Searching for a Photo Image The Photo Search works only in Player mode e Set the Power switch to PLAYER Set the Mode switch to TAPE SC D353 D354
53. aie mode 29 lt 9 10 Oman see page 20 Remaining tape measured in minutes Preparation OSD On Screen Display in M Cam M Player Modes SC D353 D354 D355 only 1 Photo quality 2 CARD Memory Card indicator OSD in M Cam Mode 3 Image counter f H Total number of recordable still images SOn ko Image recording and loading indicator E 3min Erase protection indicator see page 97 g MoNeroycas A Print mark see page 108 1 5 i a KE Folder number file number see page 89 Nite Pix JPEG image size Slide show 12 00 AM JAN 1 2005 w IT Os O 0 CON gt Turning the OSD On Screen Display On Off Turning OSD on off OSD in M Player Mode Press the DISPLAY button on the left side control panel F Each press of the button toggles the OSD function on and off m she 2460 When you turn the OSD off 800xe00 7 8 In CAMERA Mode The STBY REC modes are always displayed on the OSD even when the OSD is turned off and the key input is displayed for 3 seconds then turned off 5s w In PLAYER Mode When you press any function button the function is displayed ai on the OSD for 3 seconds before it turns off Turning the Date Time on off To turn the Date Time on or off access the menu and change the Date Time mode see page 33 No Memory Card 12 00 AM JAN 1 2005 100 0002 7 System Menu Setting Selecting the OSD Language Th
54. aking or hand movement while holding the Camcorder within reasonable limits It provides more stable pictures when Recording with the zoom DIS is not available in Digital Zoom mode Recording a small object close up Recording and walking at the same time Recording through the window of a vehicle J Camera Mode _ Program AE gt Auto White Balance _ Auto Digital Effect Off DIS Off Digital Zoom Off Set the Power switch to CAMERA 2 Set the Mode switch to TAPE SC D353 D354 D355 only 3 Press the MENU button The menu list will appear ke AMove Ellselect PEW Exit J 4 Move the Menu selector to the left or right to select Camera then press the Menu selector 5 Move the Menu selector to the left or right to select DIS then press the Menu selector g y 6 To activate the DIS function move the Menu selector to the left or right to select On Si Camera Mode then press the Menu selector Program AE If you do not want to use the DIS function set the DIS menu to Off aoe 7 To exit press the MENU button DIS Off Digital Zoom vOn DIS 4f icon is displayed on the LCD screen Re E Move Pi Select ma S Notes O p STBY 0 00 10 Digital Zoom COLOR NITE SHUTTER 16 9 Wide Emboss2 Pastel2 Mirror or Mosaic is 60min not available in the DIS mode w When you press the PHOTO button while the DIS function is enabled the DIS will be released shortly and resume aut
55. and Maintaining the Camcorder Cleaning the Video Heads To ensure normal recording and clear pictures clean the video heads when the playback pictures display square block shaped noise or distortion or a blue screen appears blue screen Set the Power switch to PLAYER Set the Mode switch to TAPE SC D353 D354 D355 only Insert the cleaning tape Press the II PLAY STILL button Press the W STOP button after 10 seconds IRUN Notes m Check the quality of the picture using a videocassette If the picture quality has not improved repeat the operation m Clean the video heads with a dry type cassette cleaner Some cleaning cassette products stop automatically Refer to the cleaning cassette s instructions for detailed information If the problem continues after the cleaning consult your nearest Samsung dealer or Authorized Service Center ENGLISH Maintenance Using Your Camcorder Abroad Each country or region has its own electric and color systems Before using your Camcorder abroad check the following items Power sources m You can use your Camcorder in any country or area with the supplied AC Power adapter within 100V to 240V 50 60 Hz Use acommercially available AC jack adapter if necessary depending on the design of the local wall outlet Color system You can view your recording in the Viewfinder However to view it on a television or copy it to a videocassette recorder the televis
56. as the power source for the Camcorder Connecting to a TV which has Audio Video Input Jacks 1 Connect the Camcorder to your TV with the Audio Video cable The yellow jack Video The white jack Audio L mono The red jack Audio R If you connect to a monaural TV connect the yellow jack Video to the video input of the TV and the white jack Audio L to the audio input of the TV 2 Set the Power switch to PLAYER 3 Set the Mode switch to TAPE SC D353 D354 D355 only 4 Turn on the TV and set the TV VIDEO selector on the TV to Video Refer to the TV user s manual 5 Play the tape Notes S Video input j Video input Yellow Audio input left White OOH Audio input 9 right Red Audio Video S Video Camcorder m You may use an S Video optional cable to obtain better quality pictures if you have a S Video connector on your TV Even if you use an S Video optional cable you need to connect an audio cable If you connect the cable to the Audio Video jack you will not hear sound from the Camcorder s speakers If only a mono audio input is available on the TV set use the audio cable with the white jack Audio L Playback Connecting to a TV which has no Audio and Video Input Jacks 1 IRUN Playback eeN You can connect your Camcorder to a TV through a VCR Connect the Camcorder to your VCR with the Audio Video cable Vid
57. assette door until it clicks into place Be careful to keep the hand strap away from the cassette door when closing it Closing the cassette door with the hand strap inside may cause a damage to the set The cassette is loaded automatically Note When you have recorded something that you wish to keep you can protect it so that it will not be accidentally erased a Protecting a tape Push the safety tab on the cassette so that the hole is uncovered b Removing the tape protection If you no longer wish to keep the recording on the cassette push the safety tab back so that it covers the hole How to store a tape Avoid places with magnets or magnetic interference Avoid humidity and dust prone places Keep the tape in an upright position and avoid storing it in direct sunlight Avoid dropping or knocking your tapes oog p Basic Recording Hints for Stable Image Recording While recording it is very important to hold the Camcorder correctly Fix the lens cover firmly by clipping it to the hand strap see page 18 Recording with the LCD Screen 4 1 Hold the Camcorder firmly using the hand strap 2 3 Place your left hand under or beside the LCD screen to support and adjust it Place your right elbow against your side Do not touch the built in microphone Choose a comfortable stable position for the shots that you are taking You can lean against a wall or on a table f
58. ate Time will read 12 00 AM JAN 1 2005 in the following conditions During playback of a blank section of a tape If the tape was recorded before setting the Date Time in the Camcorder When the Lithium battery becomes weak or dead m Before you use the Date Time function you must set the clock See Setting the Clock on page 27 Date amp Time C A Move K Select ma A Display Menu Setting Setting the TV Display Set the Power switch to CAMERA or PLAYER Set the Mode switch to TAPE or MEMORY CARD SC D353 D354 D355 only The TV Display function works in Camera Player M Cam M Player modes You can select the output path of the OSD On Screen Display Off The OSD appears in the LCD screen and Viewfinder only On The OSD appears in the LCD screen Viewfinder and TV Use the DISPLAY button located at the left side of the Camcorder to turn the OSD on off on the LCD screen Niewfinder TV Press the MENU button The menu list will appear Move the Menu selector to the left or right to select Display then press the Menu selector Move the Menu selector to the left or right to select TV Display then press the Menu selector C LCD Bright LCD Color Date Time To activate TV Display function move the Menu selector to the left or right to select On or Off TV Display __ then press the Menu selector To exit press the MENU button LCD Bright LCD Color Date Time TV Dis
59. ay view mode use the Quick Menu by pressing the Menu Selector Digital Still Camera Mode SC D353 D354 D355 only Protection from accidental Erasure The protection function works only in M Player mode You can protect important images from accidental erasure If you execute format all images including protected images will be erased _ Set the Power switch to PLAYER 6 Set the Mode switch to MEMORY CARD The last recorded image appears lf there are no recorded images on the Memory card No image will display on the screen Using the lt 44 gt gt REV FWD buttons search for the still image that you want to protect Press the MENU button The menu list will appear Move the Menu selector to the left or right to select Memory then press the Menu selector Move the Menu selector to the left or right to select Protect then press the Menu selector Move the Menu selector to the left or right to select On then press the Menu selector To exit press the MENU button The protection icon will be displayed Notes Protected pictures will show the mark when they are displayed If the write protection tab on the Memory card is set to LOCK you cannot set image protection C M Player Mode M Play Select Delete Delete All Protect gt of Print Mark Format Photo S Delete All Protect Print Mark Format Move Select DEY Exit
60. better image quality than Memory Stick Fon Digital Still Camera Mode SC D353 D354 D355 only Using Quick Menu M Play Select Quick menu is used to access Camcorder functions by simply using the Menu selector Quick menu provides easier access to the frequently used menus without using the MENU button 1 Press the Menu selector 2 Move the Menu selector to the left or right to select M Play Select then press the Menu selector 3 Move the Menu selector to the left or right to select Photo or Movie then press the Menu selector 4 To exit press the MENU button 2 46 800x600 MIPIAVISEIECHI Photo Delete Protect Print Mark GG exit la 100 0002 J 2 46 800x600 a MiPiay selec Movie Delete z Protect Print Mark E Ext 100 0002 Digital Still Camera Mode SC D353 D354 D355 only Recording an Image from a Cassette as a Still Image This function works only in Player mode You can record still images from a cassette on a Memory card If you want to move recorded multiple still images from a cassette to a Memory card use the COPY function 1 Set the Power switch to PLAYER 2 Set the Mode switch to TAPE 3 Playback the cassette 4 Press the PHOTO button The still image is recorded on the Memory card During the time it takes to save an image the play back screen is paused and the OSD is displayed as illustrated in the lower right hand corner N
61. button The menu list will appear Move the Menu selector to the left or right to select System then press the Menu selector Move the Menu selector to the left or right to select Beep Sound then press the Menu selector Move the Menu selector to the left or right to select On or Off then press the Menu selector To exit press the MENU button Ne Clock Set Beep Sound gt On Language English Demonstration gt On Em Move Eselet DEY Exit J lt a S Camera Mode Clock Set Beep Sound Language Demonstration W Move Bisect PEM Exit J A System Menu Setting Setting the Shutter Sound SC D353 D354 D355 only The Shutter Sound function works in both Player and M Cam modes You can turn the Shutter Sound on or off when on with each press of the PHOTO button the Shutter will Sound 1 Set the Power switch to CAMERA or PLAYER 2 If the Power switch is set to CAMERA mode set the MODE switch to MEMORY CARD If the Power switch is set to PLAYER mode set the MODE switch to TAPE 3 Press the MENU button The menu list will appear 4 Move the Menu selector to the left or right to select System then press the Menu selector 5 Move the Menu selector to the left or right to select Shutter Sound then press the Menu selector 6 Move the Menu selector to the left or right to select On or Off then press the Menu selector 7 To exit press the ME
62. ch functions When using this camcorder for video conferencing such as NetMeeting voice communication may not be supported depending on the video conferencing software In this case connect an external microphone to the soundcard of the PC to enable voice communication Using the Camcorder with PC Net meeting program installed you can participate in video conference The PC CAMERA s screen size Transferred video frame rate for the PC Camera function is max 15 fps If PC is connected with the USB to the Camcorder only the Power Mode Zoom and NITE PIX switches can be operated SC D352 D354 D355 only Set the Power switch to CAMERA the USB connector on your computer USB Interface SC D352 D353 D354 D355 only Using the USB Streaming Function To use USB streaming the DV Driver Video Codec and DirectX 9 0 programs must be installed in the PC You can view Camcorder video on your PC using USB streaming You can also store it as a moving picture in the avi file format or as a still image in the jpg file format on a PC Set the Mode switch to TAPE SC D353 D354 D355 only set the Power switch to CAMERA or PLAYER Connect one end of the USB cable to the USB jack on the Camcorder and the other end to the USB port on your computer Setup and execute Windows Movie Maker or the Ulead VIDEO Studio Software application provided on the CD For detailed instructions for Ulead VIDEO Studio use refer to the program s Help fun
63. co purYetow The yellow jack Video e gg tet wne m The white jack Audio L Mono ODOC iign Rea m The red jack Audio R 5 i Connect a TV to the VCR Set the Power switch to PLAYER i Set the Mode switch to TAPE SC D353 D354 D355 only aomas _ Turn on both the TV and VCR g Set the input selector on the VCR to Line m Select the channel reserved for your VCR on the TV set Play the tape You can play the recorded tape in Player mode Connect a power source and set the Power switch to PLAYER Set the Mode switch to TAPE SC D353 D354 D355 only Insert the tape you wish to play back Using the lt 4 gt REW FF buttons find the first position you wish to play back Press the II PLAY STILL button The images you recorded will appear on the TV after a few seconds f atape reaches its end while being played back the tape will rewind automatically Notes PD The playback mode SP LP is selected automatically If the VCR has an S Video input terminal you may use S Video for better quality The S Video terminal transmits video only Connect audio cables for sound If only a mono audio input is available on the TV set use the audio cable with the white jack Audio L Playback Various Functions while in Player Mode This function works only in Player mode The PLAY STILL STOP FF REW buttons are located on the Camcorder and the remote control SC D354 D355 only The F
64. condition You may select the appropriate White Balance mode to obtain good quality image color Auto A This mode is generally used to control the White Balance automatically Hold This holds the current White Balance value Indoor 4 This controls the White Balance according to the indoor ambience Under halogen or studio video lighting Subject is of one dominant color Close up m Outdoor g This controls the White Balance according to the outdoor ambience In daylight especially for close up and where the subject is of one dominant color 1 Set the Power switch to CAMERA 2 Set the Mode switch to TAPE or MEMORY CARD SC D353 D354 D355 only 3 Press the MENU button The menu list will appear 4 Move the Menu selector to the left or right to select Camera then press the Menu selector 5 Move the Menu selector to the left or right to select White Balance then press the Menu selector 6 Move the Menu selector to the left or right to select desired mode Auto Hold Indoor or Outdoor then press the Menu selector 7 To exit press the MENU button When the Auto mode is selected no icon will be displayed on the screen Camera Mode _ Program AE gt Auto White Balance _ Auto Digital Effect Off DIS Off Digital Zoom Off Move Select EE Exit NX A T m STBY oaio j f 60min lt When the Outdoor option was selected gt Ad
65. corded picture in any way it maybe difficult to see the picture clearly If this occurs we recommend using the Viewfinder Direct sunlight can damage the LCD screen Notes regarding the Hand Strap To ensure a steady picture while filming check that the hand strap is properly adjusted Do not force your hand into the hand strap as you could damage it Notes and Safety Instructions Precaution regarding the Lithium Battery 1 The Lithium battery maintains the clock function and user settings even if the Battery pack or AC adapter is removed 2 The Lithium battery for the Camcorder lasts about 6 months under normal operation from time of installation 3 When the Lithium battery becomes weak or dead the date time indicator will display 12 00 AM JAN 1 2005 when you set the Date Time to on When this occurs replace the Lithium battery with a new one type CR2025 4 There is a danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type Warning Keep the Lithium battery out of reach of children Should a battery be swallowed consult a doctor immediately Servicing Do not attempt to service this Camcorder yourself Opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by t
66. ct the USB cable to a PC via a USB HUB or simultaneously connect the a USB cable along with other USB devices the Camcorder may not work properly If this occurs remove all USB devices from the PC and reconnect the Camcorder Digital Still Camera Mode SC D353 D354 D355 only Memory Stick Optional Accessory The Memory Stick stores and manages images recorded by the Camcorder Memory STICK Functions Recording still images and MPEG4 movies Viewing still images and MPEG4 movies 7 Single e Slide show Still images only Multi display Still images only 5 Protecting images against accidental erasure Deleting images recorded on a Memory Stick Print marking still images Formatting a Memory Stick Terminal Protection tab Notes You can use most of the Camcorder s functions when recording to the Memory Stick appears on the screen while recording to the Memory Stick While recording or loading an image do not eject or insert the Memory Stick Inserting or ejecting a Memory Stick while recording or loading an image can cause data damage If you want to save all images on the Memory Stick set the write protect tab on the Memory Stick to LOCK raja Memory STICK ru a Memory Stick and S are trademarks of Sony Corporation All other product names mentioned herein may be the trademarks or registered trademarks of their respec
67. ction Windows Movie Maker is used for WINDOWS ME and XP users C program files Movie maker moviemk exe Using the removable Disk Function SC D353 D354 D355 only You can easily transfer data from a Memory card to a PC without additional add on cards via a USB connection 1 Set the Mode switch to MEMORY CARD set the Power switch to CAMERA or PLAYER 2 Connect one end of the USB cable to the USB jack on the Camcorder and the other end to the USB port on your computer 3 To verify whether the removable disk has been properly recognized open Windows Explorer and locate the removable disk WN amp amp Connecting to a PC 1 Connect a USB cable to the USB port on the PC f a USB cable is connected to the Camcorder s USB port nothing is displayed on a TV 2 Connect the other end of the USB cable into the USB jack on the Camcorder USB jack f a PC is connected to the Camcorder with a USB cable only Zoom switch and NITE PIX SC D352 D354 D355 only operate Disconnecting the USB Cable After completing the data transmission you must disconnect the cable in the following way 1 Select the removable disc icon and click the right mouse button to select Eject 2 Select Confirm and disconnect the USB cable when the Windows Splash screen appears Notes m lf you oe the USB cable from the PC or the Camcorder while transferring the data transmission will stop and the data may e damaged m if xu conne
68. des 1 Battery level see page 23 21 Tape counter 2 Digital effects mode 22 Zero memory OSD in Camera Mode see page 65 SC D354 D355 only ae 3 EASY Q see page 40 see page 42 py yy 4 DIS see page 61 23 Record speed mode om b n p sry El E 0 00 11 21 5 Program AE see page 63 24 Operating mode aT fra 108ec 14min 20 6 White balance mode 25 Self timer SC D354 D355 only 4 9 hae eB 18 see page 59 26 Photo image ae No Tape a i 18 7 Shutter speed see page 57 27 Tele MACRO see page 44 7 8 1160 PE 8 Exposure see page 57 28 Audio playback aE PS Nite Px eo 9 Manual focus see page 58 29 Volume control see page 70 40 K 12 00 AM JAN 1 2005 Color N 1 25 13 10 Date Time see page 33 30 DV IN DV data transfer mode 1 a 11 Zoom position see page 44 see page 80 7 150 00 7 12 NITE PIX see page 49 31 AV IN SC D355 only 3 9p O 10 SC D352 D354 D355 only 32 Audio dubbing 13 Color Nite see page 47 SC D354 D355 only 14 USB see page 77 OSD in Player Mode SC D352 D353 D354 D355 only 33 DEW see page 7 15 Remote see page 28 34 Warning Indicator see page 115 SC D354 D355 only 35 Message line see page 115 m it gt E 0 00 00 10 16 Wind cut see page 56 28 Sound 2 ae 17 BLC Back Light Compensation 33 4 see page 46 ci D X 18 LED LIGHT Bo re e SC D352 D354 D355 only Ay p 31 see page 48 12 00 AM JAN 1 2005 DY 30 19 oi b
69. e C W nNMove B sSeect DEY Exit j S n System Menu Setting Setting the Wireless Remote Control Acceptance Remote SC D354 D355 only The Remote function works in Camera Player M Cam M Player modes The Remote option allows you to enable or disable the remote control for use with the Camcorder 1 Set the Power switch to CAMERA or PLAYER 2 Set the Mode switch to TAPE or MEMORY CARD 3 Press the MENU button The menu list will appear 4 Move the Menu selector to the left or right to select System then press the Menu selector J Camera Mode 5 Move the Menu selector to the left or right to select Remote then press the Menu selector ok Remote gt On 6 Move the Menu selector to the left or right to select On or Off then press the Menu selector UA EA Demonstration gt On 7 To exit press the MENU button ioe Se ee S Note my Camera Mode If you set the Remote to Off in the menu and try to use it the remote control icon 1 Clock Set will blink for 3 seconds on the LCD screen and then disappear 5 Tanguage D Move PiSelect DEY Exit System Menu Setting Setting the Beep Sound se The Beep Sound function works in Camera Player M Cam M Player modes You can turn the Beep Sound on or off when on each press of a button sounds a beep Set the Power switch to CAMERA or PLAYER Set the Mode switch to TAPE or MEMORY CARD SC D353 D354 D355 only Press the MENU
70. e Language function works in Camera Player M Cam M Player modes Select the appropriate OSD Language among English French Spanish German Italian Portuguese Polish and Dutch 1 Set the Power switch to CAMERA or PLAYER 2 Set the Mode switch to TAPE or MEMORY CARD SC D353 D354 355 only 3 Press the MENU button The menu list will appear 4 Move the Menu selector to the left or right to select System then press the Menu selector 5 Move the Menu selector to the left or right to select Language then press the Menu selector The available language options are listed 6 Move the Menu selector to the left or right to select desired OSD language then press the Menu selector The OSD language is refreshed in selected language 7 To exit press the MENU button Note The word Language in the menu is always indicated in English Camera Mode Clock Set Beep Sound gt On Language English Demonstration _ gt On Move Select DEN Exit K A g N J Camera Mode v English Clock Set Fran ais Beep Sound Espa ol Deutsch Demonstration MAR Portugu s v C Move Select HEY ty System Menu Setting Setting the Clock Ca Set the Power switch to CAMERA or PLAYER Clock setup works in Camera Player M Cam M Player modes The Date Time is automatically recorded onto a tape Before recording please set the Date Time Set the Mode switch to TAPE or MEMORY CARD
71. e MACRO button again Notes When recording in Tele Macro mode the focus speed may be slow A m When you operate the Zoom function in the Tele Macro mode the recording subject um y tey 0 39 40 may be out of focus 25min Use a tripod to prevent hand shake in the Tele Macro mode Avoid shadows when recording in the Tele Macro mode As the distance to the subject decreases focusing area narrows When you can not get proper focus use the Zoom lever Basic Recording Using the Fade In and Out The FADE function works only in Camera mode You can give your recording a professional look by using special effects 77 z ane such as fade in at the beginning of a sequence or fade out at the end of SS ies Onn a sequence To Start Recording 1 Set the Power switch to CAMERA 2 Set the Mode switch to TAPE SC D353 D354 D355 only 3 Before recording hold down the FADE button The picture and sound gradually disappear fade out 4 Press the Start Stop button and at the same time release the FADE button Recording starts and the picture and sound gradually appear fade in REC 0 00 25 60min To Stop Recording use Fade In Fade Out 5 When you wish to stop recording hold down the FADE button The picture and sound gradually disappear fade out 6 When the picture has disappeared press the Start Stop button to stop recording a Fade Out Hold down the FADE button a Fade
72. e Menu selector ee 7 To exit the menu push the MENU button Protector 8 Using the lt 4 gt REV FWD buttons search for the moving picture that you want to playback es 9 Press the gt II PLAY STILL button The moving pictures recorded on the Memory card will playback m You can control playback using the II PLAY STILL lt 44 gt gt REW FF m STOP buttons Notes Delete MENU button and Menu selector are not available while MPEG playback Delete Al To use MENU button and Menu selector stop playback ae MPEG playback is not available when a menu or Quick menu is displayed on the screen ae To start playback press the MENU button to make it disappear w Move Select DEY Exit J m There may be broken or mosaic pictures while playing the MPEGd moving picture images but it is not malfunction The moving picture images that you recorded on the Memory card may not play on other manufacturer s The MPEG4 file recorded by another Camcorder may not play on by this Camcorder m To playback MPEG4 moving pictures on a PC the Video Codec in the CD provided with the camcorder should be installed You need Microsoft Windows Media Player Version 9 or higher version in order to play MPEG4 file on the Memory card on your PC You can download the Microsoft Windows Media Player applied each languages on Microsoft Website http Awww microsoft com windows Mwindowsmedia download default asp m Memory Stick PRO provides
73. e numbers may be set as follows m Series When there are existing files the new image will be named as the next number in the sequence Reset When there are no files stored on the Memory card the file numbering starts from 0001 Set the Power switch to the CAMERA Press the MENU button The menu list will appear Move the Menu selector to the left or right to select Memory then press the Menu selector Move the Menu selector to the left or right to select File No then press the Menu selector 6 Move the Menu selector to the left or right to select desired option Series or Reset then press the Menu selector To exit press the MENU button f J Photo Quality _ gt Fine M Cam Mode Series ie S v Series Reset W Move PjSelect DEY Exit P Digital Still Camera Mode SC D353 D354 D355 only Taking Photos You may take still images while in M Cam mode and store the images on the Memory card This function is useful when you want to take a snapshot of a subject while you are using the Camcorder You can take photos using the remote control SC D354 D355 only Audio will not be recorded with a Still image on to the Memory Card 1 Set the Power switch to CAMERA 2 Set the Mode switch to MEMORY CARD 3 After framing your object to record fully press the PHOTO button to take the picture The picture is taken and saved into the Memory card within a
74. e taken to keep from touching such power lines or circuits as contact with them might be fatal OVERLOADING Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock OBJECTS AND LIQUIDS Never push objects of any kind into this CAMCORDER through openings as they may touch dangerous voltage points or short out a part that could result in a fire or electric shock Never spill liquids of any kind onto the CAMCORDER Should spillage occur unplug unit and have it checked by a technician before use SERVICING Do not attempt to service this CAMCORDER yourself Opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 19 20 21 DAMAGE REQUIRING SERVICE Unplug this CAMCORDER from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the power supply cord or plug is damaged b If any liquid has been spilled onto or objects have fallen into the CAMCORDER c If the CAMCORDER has been exposed to rain or water d If the CAMCORDER does not operate normally by following the operating instructions adjust only those controls that are covered by the operating instructions Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the CAMCORDER to its normal operation e If the C
75. ection against voltage surges and built up static charges Section 810 of the National Electrical Code ANSI NFPA No 70 1984 provides information with respect to proper grounding of the mast and supporting structure grounding of the lead in wire and supporting structure grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding to conductors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode See figure below _ ANTENNA LEAD IN WIRE GROUND _ ANTENNA DISCHAF NEC SECTION 810 20 Sa l 4 corn _ EQUIPMENT Z GROUNDING CONDUCTORS NEC SECTION B1021 POWER SERVICE GROUNDING ELECTRODE SYSTEM v NEC ART 250 PART H NEC NATIONAL ELECTRICAL CODE Notices and Safety Instructions 14 15 16 17 18 LIGHTNING For added protection of this CAMCORDER during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the CAMCORDER due to lightning and power line surges POWER LINES An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits where it can fall into such power lines or circuits When installing an outside antenna system extreme care should b
76. ed dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of fire or electric shock operating and maintenance instructions in the literature accompanying f This symbol is intended to alert the user to the presence of important this product Do not use this CAMCORDER near water for example near a bathtub wash bowl kitchen sink laundry tub in a wet basement near a swimming pool or lake ACCESSORIES Do not place this CAMCORDER on an unstable cart stand tripod bracket or table The CAMCORDER may fall causing serious injury to a child or adult and serious damage to the unit Use only with a cart stand tripod bracket or table recommended by the manufacturer or sold with the CAMCORDER Any mounting of the unit should follow the manufacturer s instructions and should use a mounting accessory recommended by the manufacturer A An appliance and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the appliance and cart combination to overturn PORTABLE CART WARNING Symbol provided by RETAC Notices and Safety Instructions 9 10 11 12 VENTILATION Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the CAMCORDER and to protect it from overheating These openings must not be blocked or covered Never place your CAMCORDER on a bed sofa rug or other simila
77. er communication between the camcorder and a PC please set the USB Version before connecting Remote Language Clock Set Beep Sound USB Version USB Connect Move Select DEY Exit gt On gt On USB 1 1 gt Computer English M Player Mode Ey jf Clock Set Beep Sound USB Version USB Connect Language Move Select GQ Exit USB 1 1 USB 2 0 USB Interface SC D352 D353 D354 D355 only Installing DV Media PRO 1 0 Program To play back MPEG moving pictures recorded by the camcorder or streaming data transferred through the USB connection on a PC the Video Codec program should be installed Do not connect the Camcorder to PC before installing the program If another Camcorder or scanner is connected please disconnect it in advance This explanation is based on Windows 98SE OS DV Media Pro User s Manual is included on the accompanying CD D help in Adobe s Portable Document Format PDF The user s manual can be viewed using Acrobat Reader software which is also included on the CD DASupport AcrobatReader AcroReader51_ENU_full exe The Acrobat Reader is a freeware product of AdobeSystems Inc DV Media Pro DV Media Pro User s Manual is in English Setup Program Install Drivers Install Applications Program Installation 1 Insert the software CD into the CD ROM drive of your computer Installation selection screen appears on the monitor 2 If the installa
78. even when it is fully recharged Do not put the Battery pack near any heat source i e fire or a heater Do not disassemble apply pressure to or heat the Battery pack m Do not allow the and terminals of the Battery pack to be short circuited It may cause leakage heat generation induce overheating or fire Use SB LSM80 or SB LSM160 Battery pack only It is recommended to use original battery pack that is available at SAMSUNG service center Preparation Battery Level Display The battery level display indicates the amount of power remaining in the Battery pack a Fully charged b 20 40 used 4 c 40 80 used E d 80 95 used e Completely used Blinking E The Camcorder will turn off soon change the battery as soon as possible C Notes Blinking m Please refer to the Table on page 22 for approximate continuous recording time m The recording time is affected by temperature and environmental conditions m The recording time shortens dramatically in a cold environment The continuous recording times in the operating instructions are measured using a fully charged Battery pack at 77 F 25 C As the environmental temperature and conditions vary The remaining battery time may differ from the approximate continuous recording times given in the instructions Preparation OSD On Screen Display in Camera Player Mo
79. ewing still images recorded onto tape see page 68 Playback Controlling Sound from the Speaker The Speaker works only in Player mode When you use the LCD screen for playback you can hear recorded sound from the built in Speaker Take the following steps to lower the volume or mute the sound while playing a tape on the Camcorder 1 Set the Power switch to PLAYER 2 Set the Mode switch to TAPE SC D353 D354 D355 only 3 Press the gt II PLAY STILL to play the tape 4 When you hear sounds once the tape is in play use the Menu selector to adjust the volume Avolume level display will appear on the LCD screen Levels may be adjusted from anywhere between 00 to 19 and you will not hear any sound when the volume is set on 00 If you close the LCD screen while playing you will not hear sound from the speaker Notes m When the AV cable is connected to the Camcorder you cannot hear sound from the Built In Speaker and cannot adjust the volume mm gt 0 46 00 11 m The sound will return when you remove the connected AV cable from the jack of your Camcorder eon 4 05 Q Playback Tape Playback The playback function works only in Player mode Playback on the LCD Screen Itis practical to view a tape using the LCD screen when in a car or outdoors Playback on a TV Monitor To play back a tape the television must be NTSC compatible see page 114 We recommend that you use the AC Power adapter
80. ftware CD SC D352 D353 D354 D355 only Lens Cover Lens Cover Strap Optional Accessories 12 13 aA S Video Cable Memory Stick SC D353 D354 D355 only 1 Lithium lon Battery Pack AD43 00136A 2 AC Power Adapter AA E8 TYPE LAA i 3 AD44 00090A 3 AC Cord AD39 00076A 4 Audio Video Cable AD39 00001A 5 Instruction Book L 6 Lithium Battery CR2025 S AD43 10130H A 7 Remote Control AD59 00085A 8 USB Cable K AD39 00073A 9 Software CD 10 Lens Cover AD97 07354B 11 Lens Cover Strap B AD72 00049A 12 S Video Cable AC39 42001Z 13 Memory Stick 7 1109 001221 Getting to Know Your Camcorder Front amp Left View 6 EASY Q button 1 Lens 7 Function buttons 2 LED light REC SEARCH FADE BLC SC D352 D354 D355 only CJA REV FWD S SHOW MULTI DISP 8 TFT LCD screen 3 Remote sensor SC D354 D355 only 4 S Video jack 9 IR Infrared light 5 Internal MIC SC D352 D354 D355 only 1 Lens 6 EASY Q button 8 TFT LCD screen 2 LED light see page 48 see page 40 9 IR Infrared light SC D352 D354 D355 only 7 Function buttons SC D352 D354 D355 only 3 Remote sensor PLAYER CAMERA M Player SC D353 D354 D355 only SC D354 D355 only EASY Q p 4 S Video jack REW REC SEARCH 5 Internal MIC FF REC SEARCH PLAY STILL FADE S SHOW SL
81. g shock to Memory card After pulling the Memory card out from the Camcorder please keep the Memory card in a soft case to prevent static shock The stored contents may be changed or lost as a result of misuse static electricity electric noise or repair Save important images separately Samsung is not responsible for data loss due to misuse Digital Still Camera Mode SC D353 D354 D355 only Structure of Folders and Files on the Memory Card The still images that you recorded are saved in JPEG file format on the Memory card The moving images that you recorded are saved in MPEG4 file format on the Memory card Each file has a file number and all files are assigned to a folder A file number from DCAMO0001 is sequentially assigned to each recorded image Each folder is numbered from 100SSDVC and recorded on the Memory card Image Format Still Image Images are compressed in JPEG Joint Photographic Experts Group format m The picture size is 800x600 Tape Capture 640x480 Moving Image Images are compressed in MPEG 4 Moving Picture Experts Group format The picture size is 720x480 Selecting the Camcorder Mode You can use this Camcorder as a Digital Still Camera DSC You have to set the Mode switch to Memory card to use this Camcorder as Digital Still Camera M Cam mode Memory record mode 1 Set the Power switch to CAMERA 2 Set the Mode switch to MEMORY CARD M Player mode Memory playback mode
82. ged When the battery reaches the end of its life please contact your local dealer The batteries have to be dealt with as chemical waste Notes regarding the Video Head Cleaning To ensure normal recording and a clear picture clean the video heads regularly If a square block shape distorts playback or only a blue screen is displayed the video heads may be dirty If this happens clean the video heads with a dry type cleaning cassette Do not use a wet type cleaning cassette It may damage the video heads Notes and Safety Instructions Note regarding the Lens Do not film with the camera lens pointing directly at the sun Direct sunlight can damage the CCD Charge Coupled Device Notes regarding electronic Viewfinder 1 2 3 Do not position the Camcorder such that the Viewfinder is pointing towards the sun Direct sunlight can damage the inside of the Viewfinder Be careful when placing the Camcorder under sunlight or near a window exposed to sunlight Do not pick up the Camcorder by holding the Viewfinder Applying excessive force to the Viewfinder may damage it Notes regarding Record or Playback Using the LCD Screen 1 3 When you use the LCD screen under direct sunlight or outdoors The LCD screen has been manufactured using high precision technology However there may be tiny dots red blue or green in color that appear on the LCD screen These dots are normal and do not affect the re
83. he manufacturer and having the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards Getting to Know Your Camcorder Features Multi OSD Language You can select the desired OSD language among English French Spanish German Italian Portuguese Polish and Dutch Digital Data Transfer Function with IEEE1394 By incorporating the IEEE 1394 i LINK i LINK is a serial data transfer protocol and interconnectivity system used to transmit DV data high speed data transport port both moving and still images can be transferred to a PC making it possible to produce or edit various images USB Interface for Digital Image Data Transfer SC D352 D353 D354 D355 only You can transfer images to a PC using the USB interface without an add on card PHOTO The photo function lets you capture an object as a still along with sound while in camera mode 900x Digital Zoom Allows you to magnify an image up to 900 times its original size Color TFT LCD A high resolution color TFT LCD gives you clean sharp images as well as the ability to review your recordings immediately Digital Image Stabilizer DIS The DIS compensates for any handshake reducing unstable images particularly at high magnification Various Digital Effects The digital effects allows you to give your films a special look by adding various special effects Back Light Compensation BLC The BLC function compensa
84. he memory type Vv Y Yv 90 Photo Quality Selecting Image Quality Vv 91 92 M Play Select Selecting Storage Media Photo Movie to playback v 103 104 Delete Deleting Files v 99 100 Delete All Deleting All files Vv 99 Protect Preventing Accidental Erasure Yv 97 98 Print Mark Print images recorded on a Memory Card Y 108 109 Copy To Copying the image of Memory card to int memory Yv 107 Format Formatting the Memory Card Vv 101 File No File Naming Options Y 93 SC D353 D354 D355 only SC D355 only SC D354 D355 only Advanced Recording Available mode Main Menu Sub Menu Functions Page Camera Player M Cam MPlayer Display LCD Bright Setting the Brightness tone of the LCD screen Y Y Vv v 32 LCD Color Setting the Color tones of the LCD screen Y Y Vv Yv 32 Date Time Setting the Date and Time Y Y Y Yv 33 TV Display Selecting OSD on off of TV Vv Vv Vv v 34 System Clock Set Setting the time Y Y Y Yv 27 Remote Using the remote control Y Y Y Yv 28 Beep Sound Setting the Beep sound Y Y Vv Yv 29 Shutter Sound Setting the Shutter sound Y Vv 30 USB Version Setting the USB Version Vv Yv 83 USB Connect Setting the USB Vv 82 Language Selecting the OSD language Y Y Y Y 26 Demonstration Demonstration Y 31 SC D353 D354 D355 only SC D354 D355 only SC D352 D353 D354 D355 only Advanced Recording Function avai
85. in conditions that make automatic focusing difficult and or unreliable Manual Focus can be set in the Quick Menu Auto Focusing If you are inexperienced in the use of Camcorders we recommend that you make use of Auto Focus Manual Focusing In the following situations you may obtain better results by adjusting the focus manually a Apicture containing several objects some close to the Camcorder others further away b Aperson enveloped in fog or surrounded by snow Very shiny or glossy surfaces like a car People or objects moving constantly or quickly like an athlete or a crowd 29 Set the Power switch to CAMERA Set the Mode switch to TAPE or MEMORY CARD SC D353 D354 D355 only Press the Menu selector Move the Menu selector to the left or right to select Manual Focus then press the Menu selector 5 Move the Menu selector to the left or right to select On then press the Menu selector a M Focus MF icon will blink 6 Move the Menu selector to the left or right until the object is in focus AON Note Manual Focus is not available in the EASY Q mode A Shutter White Balance Exposure 0 00 10 60min 0 00 10 fi 60min Advanced Recording Setting the White Balance The White Balance function works in both Camera and M Cam modes The White Balance is a recording function that preserves the unique image color of the object in any recording
86. ion of your hand Hand Strap 1 Insert the Hand strap into the Hand strap hook on the front side of the Camcorder and pull its end through the hook 2 Insert your hand into the hand strap and adjust its length for your convenience 3 Close the Hand strap When You carry Your Camcorder 1 Pull and open the Hand strap cover to release the Hand strap 2 Remove it from the ring and adjust its length 3 Put your hand through the Hand Strap and close the cover of Hand Strap Attaching the Lens Cover 1 Hook up the Lens cover with the Lens cover strap as illustrated 2 Hook up the Lens cover strap to the Hand strap and adjust it following the steps as described for the Hand strap 18 3 Close the Hand strap Preparation Lithium Battery Installation Battery Installation for the Internal Clock on Battery Installation for the Remote Control SC D354 D355 only Note The Lithium battery must be inserted in the correct direction Warning Keep the Lithium battery out of the reach of the children Remove the Lithium ion battery from the rear of the Camcorder Open the Lithium battery cover on the rear of the Camcorder Position the Lithium battery in the Lithium battery holder with the positive Close the Lithium battery cover The Lithium battery maintains the clock function and preset contents of the memory even if the Battery pack or AC Power adapter is removed
87. ion or VCR must be NTSC compatible and have the appropriate audio video jacks Otherwise you may need to use a transcoder PAL compatible Countries Regions Australia Austria Belgium Bulgaria China CIS Czech Republic Denmark Egypt Finland France Germany Greece Great Britain Holland Hong Kong Hungary India Iran Iraq Kuwait Libya Malaysia Mauritius Norway Romania Saudi Arabia Singapore Slovak Republic Spain Sweden Switzerland Syria Thailand Tunisia etc NTSC compatible Countries Regions Bahamas Canada Central America Japan Korea Mexico Philippines Taiwan United States of America etc Note You can make recordings with your Camcorder and view pictures on the LCD screen from anywhere in the world Troubleshooting Troubleshooting Before contacting a Samsung authorized service center perform the following simple checks They may save you the time and expense of an unnecessary call Self Diagnosis Display Display Blinking Informs that Action a slow the Battery pack is almost discharged Change to a charged one When the remaining time on the tape Tape end slow iS about 2 minutes Prepare a new one Tape end no the tape reached its end Change to a new one No Tape there is no tape in Camcorder Insert a tape If you want to record release Protection the tape is protected from recording the protection the Camcorder has some mechanical 1
88. ions are listed White Balance BS SEN Digital Effect Portrait DIS tlic 6 Move the Menu selector to the left or right to select desired program AE option then press the Digital Zoom a Menu selector C Move Select EN Exit J 7 To exit press the MENU button The icon of the selected mode will be displayed on the LCD screen mm sTBY 0 00 10 m When the Auto mode is selected no icon will be displayed on the screen 60min Program AE White Balance Shutter Using Quick Menu Program AE 1 Press the Menu selector Exposure Manual Focus mea J 2 Move the Menu selector to the left or right to select Program AE then press a the Menu selector sTBY a poe DIS a 3 Move the Menu selector to the left or right to select desired program AE option then press the Menu selector Shutter Exposure Manual Focus 4 To exit press the MENU button N Exit J Advanced Recording Applying Digital Effects The Digital Effect function works only in Camera mode The Digital Effects enable you to give a creative look to your recording Select the appropriate Digital Effect for the type of picture that you wish to record and the effect you wish to create There are 11 Digital Effect modes ART mode This mode gives the images a coarse effect 2 Mosaic mode This mode gives the images a mosaic effect 3 Sepia mode This mode gives the images a reddish brown pigment
89. ithout notice Index Accessories AFIMP 0000 Audio Dubbing Audio Mode Battery Pack BLC Cassette Cleaning Clock Set Connecting Date Time DC Cable Deleting Demonstration DIS EASY Q Mode Exposure Fade Formatting Frame advance Function buttons Hand Stree esc oh cect n A A i BEEN 394 Kiaat ii tiia i aE a Memory card Memory Stick MPEG Recording Boye OSD A ace NE Nea NY Re oan dog Ae loss Ni seca te 24 25 P Photo Copy 106 Photo Quality 91 PHO Sear eissecscecasacavensceceve otccceewsatecueceatitavests cuecehletiesuasces Ge fetavas nce aaee 68 Program AE Protection Rec Mode Rec Search Remote Remote control Shutter Speed Sound Speaker Still images Tele MACRO TV Display White Balance Wind Cut ZERO MEMORY Zoom Warranty SEA users only SAMSUNG LIMITED WARRANTY SAMSUNG Electronics America Inc SEA warrants that this product is free from defective material and workmanship SEA further warrants that if product fails to operate properly within the specified warranty period and the failure is due to improper workmanship or defective material SEA will repair or replace the product at it s option All warranty repairs must be performed by a SEA authorized service center The name and address of the location nearest you can be obtained by calling toll free 1 800 SAMSUNG
90. ivated leave the Camcorder for at least two hours in a dry warm room with the cassette compartment opened and the Battery pack removed Notes regarding Camcorder 1 Do not leave the Camcorder exposed to high temperatures above 60 C or 140 F For example in a parked car in the sun or exposed to direct sunlight 2 Do not let the Camcorder get wet Keep the Camcorder away from rain sea water and any other form of moisture If the Camcorder gets wet it may get damaged Sometimes a malfunction due to exposure to liquids cannot be repaired Notes and Safety Instructions Notes regarding the Battery Pack It is recommended to use original battery pack that is available at SAMSUNG service center Make sure that the Battery pack is fully charged before starting to record To preserve battery power keep your Camcorder turned off when you are not operating it If your Camcorder is in CAMERA mode and it is left in STBY mode without being operated for more than 5 minutes with a tape inserted it will automatically turn itself off to protect against unnecessary battery discharge Make sure that the Battery pack is fitted firmly into place Do not drop the Battery pack Dropping the Battery pack may damage it A brand new Battery pack is not charged Before using the Battery pack you need to charge it completely Fully discharging a Lithium lon battery damages the internal cells The Battery pack may be prone to leakage when fully dischar
91. lability in each Mode Requested Digital functions Digital Effects ok Operating Mode Ts ital Zoom PHOTO Color Nite 169 Emboss2 Pastel2 the other _ Nite Pix Mode 9 TAPE Shutter Wide Mirror Mosaic Digital Effect DIS x we x x x 0 0 Digital Zoom A X w we x O O PHOTO TAPE x x x x x x Color Nite Shutter A x x 0 O 16 9 Wide A A A Emboss2 Digital Pastel2 x Effects Mirror A o A A Mosaic the other Digital Effect O O O O A Nite Pix O O O O x x x O The requested mode will work in this operating mode X You can not change the requested mode A The requested mode will work yx The requested mode will work operating mode data will be backed up This Function works on models SC D352 D354 D355 only Note When you select an item that cannot be changed an error message will be displayed Advanced Recording Selecting the Record Mode The Record Mode function works in both Camera and Player DV IN modes This Camcorder records and plays back in SP standard play mode and in LP long play mode SP standard play This mode permits 60 minutes of recording time with a DVM60 tape LP long play This mode permits 90 minutes of recording time with a DVM60 tape Set the Power switch to CAMERA or PLAYER Set the Mode switch to TAPE SC D353 D354 D355 only Press the MENU button The menu list will appear
92. layer Mode Clock Set Remote Beep Sound USB Version USB Connect Language XN Move Select GQ Exit gt On gt On gt USB 1 1 Computer gt English C M Player Mode Clock Set Remote Beep Sound USB Version USB Connect Language Computer Move Select DEY Exit Printer M Player Mode Boops Num 002 Num 002 Date Time Ez Previous Next ad 100 0002 PictBridge SC D353 D354 D355 only Setting the Date Time Imprint Option 4 Move the Menu selector to the left or right to select Date Time then press the Menu selector 5 Move the Menu selector to the left or right to select the Date Time display type ou then press the Menu selector voi Date Time display type Off Date Time Date amp Time p Eu C KZ Previous Next OJ eames S M Player Mode Printing Images Move the Menu selector to the left or right to select Print then press the Menu selector and selected image files will be printed M Player Mode Notes m The Date Time Imprint Option may not supported by all printers Check with your printer manufacturer The DATE TIME Menu cannot be setup if the printer does not support this option i The PictBridge is a registered trademark of CIPA Camera amp Imaging Products Association an image ggpprevious Next E 100 0002 transfer standard developed by Canon Fuji HP Olympus Seiko Epson and Sony N S
93. ly when it reaches the zero position When you have finished recording set the Power switch to PLAYER and press the 44 REW button The tape stops automatically when it reaches the zero position MEMORY TIME 5 The tape counter with the gt ZERO MEMORY indicator disappears from the display and the tape counter is changed to the time code Notes In the following situations ZERO MEMORY mode may be canceled automatically At the end of the section marked with the ZERO MEMORY function When the tape is ejected When you remove the Battery pack or power supply The ZERO MEMORY may not function correctly where there is a break between recordings on the tape in Basic Recording Self Record using the Remote Control SC D354 D355 only The SELF TIMER function works only in Camera mode When you use the Self Timer function on the remote control the recording begins automatically in 10 seconds 1 Set the Power switch to CAMERA 2 Set the Mode switch to TAPE 3 Press the SELF TIMER button until the appropriate indicator is displayed in the LCD screen 4 Press the Start Stop button to start the timer Self Timer starts counting down from 10 with a beep sound In the last one second of the countdown the beep sound gets faster then recording starts automatically If you want to cancel the Self Timer function before recording press the SELF TIMER button SELF TIMER MEMORY TIME 5 Pres
94. m the U S Government Printing Office Washington D C 20402 Stock No 004 000 00345 4 FCC Warning The user is cautioned that changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment FCC ID ASLOS5DRAGON This device complies with Part 15 of FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Contents Notes and Safety MST UCUN reeeo aAA AEAEE RARA EA A A RA EA R REAO Getting to Know Your Camcorder ssossesssssssssssssssensseeeee FCA OS face ES ASENN EN EER E A E cubase E ANA AS A A E A E NA ON 11 Accessories Supplied with Camcorder 12 Front amp Left View AB Left Side View 14 Right amp Top View 15 Rear amp Bottom View 16 Remote Control SC D354 D355 Only Asang aai haven dud nadia A nda AEAEE sin hela unr ini AEEA EEE bent ca A AEE AEE 17 Preparation 18 Adjusting the Hand Strap ai siose iea E ATA AEE O I EAE EA N EAE TRA 18 Hand Strap 18 When You carry Your Camcorder Attaching the Lens Cover Lithium Battery Installation v Battery Installation for the Internal Clock 19 Battery Installation for the Remote Control Connecting a Power Source ce ccs ieee To use the AC P
95. mory card with a printer supporting DPOF There are 2 ways to make a Print Mark This File You can set a print mark on the photo image displayed on the LCD screen It can be set up to 999 All Files To print 1 copy each of all of the stored images 1 Set the Power switch to PLAYER S M Player Mode 2 Set the Mode switch to MEMORY CARD M Play Select I gt Photo The last recorded image appears ba Protect gt of 3 Using the lt 44 gt gt REV FWD buttons search for the still image that you want to mark Print Mark 4 Press the MENU button The menu list will appear D 5 Move the Menu selector to the left or right to select Memory then press the Menu selector Decenii A 6 Move the Menu selector to the left or right to select Print Mark then press the Menu selector Paea This Fi Print Mark VAII Files Format 7 Move the Menu selector to the left or right to select desired option All Off This File or All Files C KZ Previ Next DA then press the Menu selector He A A m r m 2 46 4 PA 8 If you select This File move the Menu selector to the left or right to select the quantity Man then press the Menu selector 9 To exit press the MENU button A B 002 Removing the Print Mark TT To remove all Print Marks select All Off to remove individual file s Print Mark select the file and set 4 This File to 000 Digital Still Camera Mode SC D353 D354 D355 only Using Quick Menu Print
96. nd on a pre recorded tape recorded in SP mode with 12bit sound Use the internal or an external microphone not supplied or other audio equipment The original sound will not be erased Dubbing Sound 1 Set the Power switch to PLAYER f you want to use an external microphone connect the microphone to the external MIC input jack on the Camcorder 2 Set the Mode switch to TAPE 3 Press the II PLAY STILL button and find the time frame of the scene to be dubbed 4 Press the II PLAY STILL button to pause the scene 5 Press the A DUB button on the remote control Audio Dubbing icon Q will be displayed on the LCD screen The Camcorder is ready for dubbing 6 Press the II PLAY STILL button to start dubbing Press the W STOP button to stop the dubbing Notes m You can not use the Audio Dubbing function while playing a write protected video tape To utilize an external MIC or sound source connect a microphone to the MIC jack or use the AV cable to connect external sound source input m To dub an external sound source set the AV In Out function to AV In SC D355 only see page 76 Playback Dubbed Audio Playback 1 Set the Power switch to PLAYER 2 Set the Mode switch to TAPE SC D353 D354 D355 only 3 Insert the dubbed tape and press the MENU button 4 Move the Menu selector to the left or right to select Tape then press the Menu selector 5 Move
97. ntr Menu selector ae ngis You can select Computer to use the Camcorder as a PC Camera USB Stream or removable disk 6 You can select Printer to use the Pictbridge feature see page 110 Clock Set Remote To exit press the MENU button Beep Sound _ USB Version USB Connect vComputer Language Printer C Move Select HE w USB Interface SC D352 D353 D354 D355 only Setting the USB Communication Speed SC D353 D354 D355 only the camcorder to a PC Itis available only in M Cam and M Player modes 1 Set the Power switch to CAMERA or PLAYER Set the Mode switch to MEMORY CARD Press the MENU button The menu list will appear Move the Menu selector to the left or right to select System then press the Menu selector 4 Move the Menu selector to the left or right to select USB Version then press the Menu selector m Set the USB Version to USB 2 0 when it is supported by both PC and its OS Operating System If either the PC or OS does not support USB 2 0 set the USB Version to USB 1 1 6 To exit press the MENU button Notes m When the USB Version is not set properly the USB connection may not be established USB 2 0 may not be supported by certain PCs depending on their specifications In this case choose the USB 1 1 for USB connection When selected USB 2 0 is not supported by the PC the USB 1 1 will be used for the USB connection automatically To ensure prop
98. omatically after the photo recording Advanced Recording Using Quick Menu Digital Image Stabilizer DIS Quick menu is used to access Camcorder functions by simply using the Menu selector Quick menu provides easier access to the frequently used menus without using the MENU button 1 Press the Menu selector twice D 2 Move the Menu selector to the left or right to select On or Off then press the Menu selector 3 To exit press the MENU button Notes It is recommended that you deactivate the DIS function when using a tripod m f you use the DIS function the picture quality may deteriorate m EASY Q mode automatically sets the DIS to On White Balance Shutter Exposure Manual Focus STBY 0 00 10 S E 60min Program AE White Balance Shutter Exposure Manual Focus STBY 0 00 10 x a amp 60min y Exit J gt STBY eid 60min K XX of Advanced Recording Programmed Automatic Exposure Modes Program AE The Program AE function works only in Camera mode The Program AE mode allows you to adjust shutter speeds and apertures to suit different recording conditions They give you creative control over the depth of field Auto mode A STBY E 0 00 10 Auto balance between the subject and the background 60min To be used in normal conditions The shutter speed automatically varies from 1 60 to 1 250 pe
99. or greater stability Do not forget to breathe gently Use the LCD frame as a guide to determine the horizontal plane Whenever possible use a tripod Recording with the Viewfinder oN QD 1 Hold the Camcorder firmly using the hand strap 2 3 Place your left hand under the Camcorder to support it Place your right eloow against your side Be sure not to touch the built in microphone Choose a comfortable stable position for the shots that you are taking You can lean against a wall or on a table for greater stability To view an object through the Viewfinder pull it out until you hear the click sound Excessive force may cause damage to the Viewfinder Place your eye firmly against the Viewfinder eyecup Use the Viewfinder frame as a guide to determine the horizontal plane Whenever possible use a tripod ENGLISH Basic Recording Various Recording Techniques In some situations different recording techniques may be required for more dramatic results 1 General recording 2 Downward recording Making a recording with a top view of the LCD screen 3 Upward recording Making a recording viewing the LCD screen from below 4 Self recording Making a recording viewing the LCD screen from the front 5 Recording with the Viewfinder In circumstances where it is difficult to use the LCD screen the Viewfinder can be used as a convenient alternative Note
100. otes m Still images copied from the cassette to the memory card are saved in a 640x480 format m Number of images you can save varies depending on the image resolution Pil 2 46 0 25min Now copying p Digital Still Camera Mode SC D353 D354 D355 only Copying Still Images from a Cassette to Memory Card The photo copy function works only in Player mode You can copy still images recorded with photo function on a cassette onto a Memory card Rewind the tape to the point which you wants 4 1 Set the Power switch to PLAYER 2 Set the Mode switch to TAPE 3 Press the MENU button The menu list will appear 6 4 Move the Menu selector to the left or right to select Tape then press the Menu selector 5 Move the Menu selector to the left or right to select Photo Copy then press the Menu selector All still images that recorded on a cassette will be copied into a Memory card 6 The Camcorder automatically performs the photo search to find still images and copy starts 7 Press the mi STOP button to stop copying Copy stops when the cassette is finished or Memory card is full Note Still images copied from the cassette to the memory card are saved in 640x480 format Player Mode Photo Search Photo Copy Audio Select gt Sound 1 Move Select GQ Exit S Player Mode Move Select DEY Exit Photo Copy Photo searching
101. ower Adapter and DC Cable 0 To select the Camcorder Mode SC D353 D354 D355 only Using the Lithium lon Battery Pack Charging the Lithium lon Battery Pack Table of continuous Recording Time based on Model and Battery Type Battery Level Display 0 c cccscesesseneseesse eens 23 OSD On Screen Display in Camera Player Modes OSD On Screen Display in M Cam M Player Modes SC D353 D354 D355 only Turning the OSD On Screen Display On Off eem Meni SUITS e e E ton cocerocece Sata e Cocoa E N E AAD Selecting the OSD Language Setting the Clock Setting the Wireless Remote Control Acceptance Setting the Beep Sound Setting the Shutter Sound SC D353 D354 D355 only Viewing the Demonstration Da Men e O Adjusting the LED Screens 2 ianiai aae A NEEE EEE AE E EANA EAEAN A REEERE EEEN KAET SKEA AEN 32 Displaying the Date Time Setting the TV Display A Contents Basie RCCOMGING reao EEA A E O RR ERA EE E OD Using the Viewfinder Adjusting the Focus Inserting and Ejecting a Cassette Hints for Stable Image Recording 37 Recording with the LCD Screen Recording with the Viewfinder Various Recording Techniques Making your First Recording Using EASY Q Mode for Beginners Record Search REC SEARCH Setting the Zero Memory SC D354 D355 only s s Self Record using the Remote Control SC D354 D355 only Zooming In and Out Using the Tele Macro
102. play S C W Move Wi Seect DEY Exit P Basic Recording Using the Viewfinder Inthe PLAYER mode the Viewfinder will work when the LCD screen is closed In the CAMERA mode the Viewfinder will work when the LCD screen is closed or rotated counterclockwise 180 Adjusting the Focus The focus adjustment knob of the Viewfinder enables individuals with vision problems to see clearer images 1 Close the LCD screen and pull out the Viewfinder 2 Use the focus adjustment knob of the Viewfinder to focus the picture Notes Viewing the sun or any strong light source through the Viewfinder for a prolonged period may be harmful or cause temporary impairment m The Viewfinder will work either in PLAYER mode with LCD screen closed or in CAMERA mode with LCD screen closed or facing the front Basic Recording Inserting and Ejecting a Cassette When inserting a tape or closing the cassette compartment do not apply excessive force As it may cause a malfunction Do not use any tape other than Mini DV cassettes 1 Connect a power source and slide the TAPE EJECT switch The cassette door opens automatically 2 Insert a tape into the cassette compartment with the tape window facing outward and the protection tab toward the top Inserting a Cassette m Remove the cassette tape which is automatically ejected by pulling the cassette out Ejecting a Cassette 3 Press the area marked PUSH on the c
103. r second depending on the scene B Sports mode 23 For recording people or objects moving quickly Portrait mode 4 For focusing on the background of the subject when the background is out of focus The Portrait mode is most effective when used outdoors The shutter speed automatically varies from 1 60 to 1 1000 per second Spotlight mode For recording correctly when there is only light on the subject and not the rest of the picture Sand Snow mode 22 For recording when people or objects are darker than the background because of reflected light from sand or snow High Speed High Shutter Speed mode amp For recording fast moving subjects such as players in golf or tennis games Notes While setting the NITE PIX to ON the Program AE function does not work SC D352 D354 D355 only The Program AE function will not operate in EASY Q mode Advanced Recording Setting the Program AE 1 Set the Power switch to CAMERA Camera Mode 2 Set the Mode switch to TAPE SC D353 D354 D355 only _ ProgamAE gt Auto White Balance _ Auto Digital Effect Off 3 Press the MENU button Doaz von a The menu list will appear IA NMove K Select ma 4 Move the Menu selector to the left or right to select Camera then press the Menu selector CH Camera Mode 5 Move the Menu selector to the left or right to select Program AE then press the Menu selector S AE E r The available opt
104. r surface on or near a radiator or heat register This CAMCORDER should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to POWER SOURCES The CAMCORDER should be operated only from the type of power source indicated on the label If you are not sure of the type of power supply at your home consult your appliance dealer or local power company A CAMCORDER is intended to be operated from battery power or other sources refer to the operating instructions GROUNDING OR POLARIZATION This CAMCORDER may be equipped with either a polarized 2 wire AC line plug a plug having one blade wider than the other or a 3 wire grounding type plug a plug having a third grounding pin If you are unable to insert the plug fully into the outlet try reversing the plug If the plug still fails to fit contact your electrician to replace your outlet Do not defeat the safety purpose of the polarized plug POWER CORD PROTECTION Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords or plugs convenient receptacles and the point where they exit from the unit 13 OUTDOOR ANTENNA GROUNDING If an outside antenna or cable system is connected to the CAMCORDER be sure the antenna or cable system is grounded to provide some prot
105. s on the display Notes The COLOR NITE LED LIGHT will not turn ON or OFF while you are recording The range of the LED light is limited up to 6 6ft 2m Danger The LED light can become extremely hot Do not touch it while in operation or soon after turning it off otherwise serious injury may result Do not place the Camcorder into the carrying case immediately after using the LED light since it remains extremely hot for some time Do not use near flammable or explosive materials i STBY 0 00 10 60min Ge Color N 1 15 Basic Recording Nite Pix 0 lux recording SC D352 D354 D355 only The Nite Pix function works in both Camera and M Cam modes 1 The Nite Pix function enables you to record a subject in darkness Set the Power switch to CAMERA 2 Set the Mode switch to TAPE or MEMORY CARD SC D354 D355 only 3 Slide the NITE PIX switch to ON m Nite Pix indicator appears on the LCD screen The infrared light is turned on automatically 4 To cancel the Nite Pix function slide the NITE PIX switch to OFF Notes The maximum recording distance using the infrared light is about 3 m about 10 feet If you use the Nite Pix function in normal recording situations ex outdoors by day the recorded picture may be tinted green Nite Pix is not available while taking a photo image In the Nite Pix mode certain functions are not available such as Exposure
106. s the Start Stop button again when you wish to stop recording Notes Do not obstruct the remote control sensor by putting obstacles between the remote control and Camcorder The remote control range is 4 5m 13 17 ft m The effective remote control angle is up to 30 degrees left right from the center line Using a tripod is recommended for delayed recording Basic Recording Zooming In and Out The Zoom function works in both Camera and M Cam modes Zooming is a recording technique that lets you change the size of the subject in a scene You can zoom using variable zoom speeds Use these features for different shots Please note that over use of the Zoom feature can lead to unprofessional looking results and a reduction of battery usage time Se fee 1 Move the Zoom lever slightly for a gradual zoom move it further for a high speed zoom Your zooming is monitored on the OSD 2 T Telephoto side Subject appears closer 3 W Wide angle side Subject appears farther away You can record a subject that is about 10mm about 0 5 inch away from the lens surface in the Wide position Using the Tele Macro Tele Macro Function works in both Camera and M Cam mode Effective focal distance in tele macro mode is 50 Cm 19 7 inches 100 Cm 39 4 inches 1 Press the MACRO button Tele Macro Icon 4 will be displayed 2 If you want to cancel the Tele Macro function press th
107. sing the EASY Q button all functions on the Camcorder will be set to off and the recording settings will be set to the following basic modes Battery level recording mode counter date time and DIS 4 will be displayed The word EASY Q will appear on the LCD screen at the same time However the Date Time will only be seen if it has been previously set see page 33 4 Press the Start Stop button to start recording Recording will begin using the basic automatic settings 5 Press the EASY Q button again in the STBY mode and then turn the EASY Q mode off The EASY Q function will not turn off while you are recording gt m The camcorder will return to the settings that were set prior to activating EASY Q mode pm A n EASY Q z f 60min w Notes In EASY Q mode certain functions are not available such as Menu BLC Manual focus If you want to use these functions you must first turn the EASY Q mode off The EASY Q mode settings are deleted when the Battery pack is removed from the Camcorder and must be reset when the Battery pack is replaced EASY Q mode will not turn off during a recording Taking a photo image using the PHOTO button while EASY Q is set releases DIS function Digital Zoom COLOR NITE SHUTTER or Digital Effect is not available in the EASY Q mode Basic Recording When a cassette is loaded and the Camcorder is left in the STBY mode for more than 5 minutes without being used it will switch off automatically
108. t TR LCD Bright or LCD Color then press the Menu selector Date Time gt ot TV Display gt On Move the Menu selector to the left or right to adjust the value of the selected item LCD Bright or LCD Color then press the Menu selector Nowe Aseet E j You can set values for LCD Bright and LCD Color between 0 35 ese Camera Mode D To exit press the MENU button aI LCD Bright amp LCD Color functions do not affect the brightness and color of the image LOD Coir to be recorded C Move seet MGM Exit J Display Menu Setting Displaying the Date Time The Date Time function works in Camera Player M Cam M Player modes The date and time are automatically recorded on a special data area of the tape 1 Set the Power switch to CAMERA or PLAYER 2 Set the Mode switch to TAPE or MEMORY CARD SC D353 D354 D355 only 3 Press the MENU button The menu list will appear 4 Move the Menu selector to the left or right to select Display then press the Menu selector ai 5 Move the Menu selector to the left or right to select Date Time then press the Menu selector LCD Bright LCD Color Date Time gt Off TV Display 6 Move the Menu selector to the left or right to select the display type of the Date Time then press the Menu selector m Display type of the Date Time Off Date Time Date amp Time 7 To exit press the MENU button LCD Bright Notes LCD Color m The D
109. tes for the bright background behind a subject you re recording Program AE The program AE enables you to alter the shutter speed and aperture to suit the type of scene action to be filmed NITE PIX SC D352 D354 D355 only The NITE PIX function enables you to record a subject in a dark place Digital Still Camera Function SC D353 D354 D355 only Using Memory card you can easily record and playback standard still images You can transfer standard still images on the Memory card to your PC using the USB interface MPEG Recording SC D353 D354 D355 only MPEG recording makes it possible to record video onto a Memory card Multi Memory Card Slot SC D355 only Multi Memory card slot is able to use Memory Stick Memory Stick PRO MMC and SD Built in Memory SC D354 D355 only You can use digital still camera functions without a separate external Memory card using the built in memory installed in your Camcorder SC D354 32MB SC D355 64MB Aa Getting to Know Your Camcorder Accessories Supplied with Camcorder Make sure that the following basic accessories are supplied with your digital video camera Basic Accessories 1 2 oar w 8 9 10 11 Lithium lon Battery Pack AC Power Adapter AA E8 TYPE AC Cord Audio Video Cable Instruction Book Lithium Battery for Remote Control SC D354 D355 only or Clock TYPE CR2025 Remote Control SC D354 D355 only USB Cable SC D352 D353 D354 D355 only So
110. that the Memory card is inserted into Camcorder before connecting USB cable If no Memory card or an unformatted Memory card is inserted PC will not recognize your Camcorder as a removable disk SC D353 D354 D355 only USB Streaming requires Video Codec DV Driver and DirectX 9 0 If you disconnect the USB cable from the PC or the Camcorder during the data transfer the data transfer will stop and the data may be damaged If you connect the USB cable to a PC using a USB HUB or with other devices at the same time it may cause conflict and may not work properly If this occurs remove all other USB devices and try the connection again USB Interface SC D352 D353 D354 D355 only Selecting the USB Device SC D353 D354 D355 only Set the Power switch to PLAYER USB Select function works only in M Player mode Using the USB cable you can connect your Camcorder to a computer to copy your movies and images from the Memory card or built in memory SC D354 D355 or to a printer to print your images Set the Mode switch to MEMORY CARD Press the MENU button The menu list will appear Move the Menu selector to the left or right to select System then press the Menu selector Move the Menu selector to the left or right to select USB Connect then press the ETT Menu selector Remote gt On Beep Sound gt On USB Version USB 1 1 Move the Menu selector to the left or right to select Computer or Printer then press the co
111. till image that you want to delete C Move Select ma S 4 Press the MENU button m The menu list will appear 6 M Player Mode M Play Select Delete All Protect Print Mark Format 5 Move the Menu selector to the left or right to select Memory then press the Menu selector 6 Move the Menu selector to the left or right to select Delete then press the Menu selector Amessage Do you want to delete appears W Move K Select ma 7 Move the Menu selector to the left or right to select Yes or No then press the 7 n Menu selector D 2460 800x600 8 To exit press the MENU button D Do you want to delete E M Deleting All images at once Move the Menu selector to the left or right to select Delete All then press the Menu selector A message Do you want to delete all appears KX Previous Next D 100 0002 A Digital Still Camera Mode SC D353 D354 D355 only Using Quick Menu Delete Quick menu is used to access Camcorder functions by simply using the Menu selector Quick menu provides easier access to the frequently used menus without using the MENU button 1 Press the Menu selector A a 2146 2 Move the Menu selector to left or right to select Delete then press the Menu selector ee 3 Move the Menu selector to the left or right to select Cancel or Delete then press the Seed Menu selector Prote Print Mark xi 00 0002 4 To exit
112. tion Cable 1 2 3 Set the Power switch to PLAYER Set the Mode switch to TAPE SC D353 D354 D355 only Connect the DV cable not supplied from the DV jack of the Camcorder to the DV jack of the other DV device Make sure that Dw is displayed on the LCD screen Press the Start Stop button to begin REC PAUSE mode PAUSE is displayed on the LCD screen Start playback on the other DV device while you monitor the picture Press the Start Stop button to start recording f you want to pause recording momentarily press the Start Stop button again To stop recording press the W STOP button Notes When using this Camcorder as a recorder the pictures that appear on a monitor may seem uneven Operation is not guaranteed for all the recommended computer environments mentioned above however recorded pictures will not be affected XX Beeoo USB Interface SC D352 D353 D354 D355 only Transferring a Digital Image through a USB Connection The camcorder supports both USB 1 1 and 2 0 standards Depends on the PC specification You can easily transfer a image from a Memory card to a PC without additional add on cards via a USB connection You can transfer a recorded file in memory card to a PC via a USB connection SC D353 D354 D355 only If you transfer data to a PC you need to install the software DV Driver Video Codec DirectX 9 0 supplied with the Camcorder
113. tion selection screen does not appear after inserting the CD click Run in the Windows Start menu and execute Autorun exe file to begin installation When CD ROM drive is set to D drive type D autorun exe and press Enter 3 Click the icons listed below to install the selected software DV Driver Click USB removable Disk Driver Windows 98SE only USB PC CAMERA amp STREAMING Driver CAPTURE DRIVER Connect a Camcorder to your PC to complete the DV Driver installation 1 Set the camcorder Power switch to CAMERA 2 Set the camcorder Mode switch to TAPE SC D353 D354 D355 only 3 Connect the camcorder to the PC using the USB cable 4 The SAMSUNG A V Capture driver installation begins on the PC DirectX 9 0 Click Video Codec Click The Video Codec needs to be installed in order to playback the MPEG4 Movies stored in the Memory Card on a PC or to use the USB Streaming PC Camera functions A USB Interface SC D352 D353 D354 D355 only Using the PC Camera Function Se fe ogo of Se fe of Set the Mode switch to TAPE SC D353 D354 D355 only Connect one end of the USB cable to the USB jack on the Camcorder and the other end to To use the PC Camera function the DV Driver Video Codec and DirectX 9 0 programs must be installed in the PC You can use this Camcorder as a PC CAMERA When you connect to a Web site that provides video chatting functions you can use your Camcorder for su
114. tive companies Furthermore and are not mentioned in each case in this manual Digital Still Camera Mode SC D353 D354 D355 only Inserting and Ejecting the Memory Card Inserting the Memory card 1 Set the Power switch to Off 2 Open the Memory card cover 3 Insert the Memory card in the direction of the arrow into the Memory card slot located on the bottom of the Camcorder A SC D353 D354 only Ejecting the Memory card 1 Set the Power switch to Off sity a saa 2 Open the Memory card cover Se 3 Push the Memory card then it comes out of the Camcorder automatically 4 Pull out the Memory card SC D355 only Do not attempt to pull the Memory card out without first pushing it in eLa Memory Stick Memory Stick PRO Notes m Memory Stick Duo type or RS MMC SC D355 only should be inserted by using the Adaptor not supplied SONS f you set the Camcorder to M Player mode the last recorded still image appears If there are no recorded images on the Memory card No image will display on the Usable Memory card screen While recording loading erasing or formatting do not turn off the power or change the mode Please turn the power off before you insert or eject the Memory card You could lose data on the Memory card Do not allow metal substances to come in contact with the terminals of the Memory card Do not bend drop or apply stron
115. to search for an image quickly To view a Slide Show 1 Set the Power switch to PLAYER 2 Set the Mode switch to MEMORY CARD The last recorded image appears 3 Press the gt II S SHOW button All images will be played back consecutively for 2 3 seconds each The Slide will be display on the LCD screen 4 To stop the slide show press the gt I1 S SHOW button again Notes m Loading time may vary depending on the image size The Slide Show will start from the current picture a m Any large sized image taken with another device will be displayed as a thumbnail image Digital Still Camera Mode SC D353 D354 D355 only To view the Multi Display 1 Set the Power switch to PLAYER 2 Set the Mode switch to MEMORY CARD The last recorded image appears 3 To view six stored images on single screen press the W MULTI DISP button A selection mark 44 gt appears under the image m Press 4 gt gt REV FWD button to select an image SEE 4 To return to single playback mode press the W MULTI DISP button again Selected picture is displayed in full screen mode CDD Notes WD S SHOW MULTI DISP To display the previous six images press and hold the 4 REV button for about 3 seconds To display the next six images press the gt FWD button for about 3 seconds In order to use Delete Protect or Print Mark functions in Multi Displ
116. u can control the printer directly through your Camcorder in order to print out stored pictures For direct printing of your stored pictures using the PictBridge function you must connect your Camcorder to a PictBridge printer using a USB cable Connecting To a Printer 1 Turn your printer power off Turn your Camcorder on by setting the Power switch to PLAYER Set the Mode switch to MEMORY CARD Press the MENU button The menu list will appear Move the Menu selector to the left or right to select System then press the Menu selector Move the Menu selector to the left or right to select USB Connect then press the Menu selector Move the Menu selector to the left or right to select Printer then press the Menu selector Computer Connect to a computer Printer Connect to a printer To use the PictBridge function connect to a printer Connect your Camcorder to the printer using the provided USB cable Turn your printer power on The PictBridge menu screen appears automatically after a short period The cursor highlights Printer Selecting Images 1 In the PictBridge settings menu press the lt 44 gt gt REV FWD buttons to select an image to print Setting the Number of Prints 2 Move the Menu selector to the left or right to select Copies then press the Menu selector 3 Move the Menu selector to the left or right to set the number of prints then press the Menu selector Fin M P
117. u selector 6 Move the Menu selector to the left or right to select desired shutter speed or exposure _ STBY 0 00 10 then press the Menu selector els Shutter speed can be set to 1 60 1 100 1 250 1 500 1 1000 1 2000 1 4000 or 1 10000 i _ Exposure value can be set between 00 and 29 7 To exit press the MENU button os Selected settings are displayed on the screen Et J Recommended Shutter Speeds when Recording Outdoor sports such as golf or tennis 1 2000 or 1 4000 Moving cars or trains or other rapidly moving vehicles such as roller coasters 1 1000 1 500 or SE o o 1 250 Indoor sports such as basketball 1 100 EE o o Notes Wi D m f you manually change the Shutter Speed and the Exposure value when Program AE option is selected manual changes are applied first m The image may not seem as smooth when a high Shutter Speed is set m The Camcorder returns to the auto shutter and auto exposure settings when you set the NITE PIX to ON or change to the EASY Q mode SC D352 D354 D355 only m When recording with a Shutter Speed of 1 1000 or higher make sure the sun is not shining into the lens Advanced Recording Auto Focus Manual Focus The Auto Focus Manual Focus function works in both Camera and M Cam modes In most situations it is better to use the automatic focus feature as it enables you to concentrate on the creative side of your recording Manual focusing may be necessary under certa
118. urchase m To prevent reduction in the life and capacity of the Battery pack always remove it from the Camcorder after it is fully charged The amount of continuous recording time available depends on The type and capacity of the Battery pack you are using How often the zoom is used Type of use Camcorder Camera With LCD screen etc Ambient temperature It is recommended to have additional battery packs available m Even when the Power switched Off the Battery pack will still discharge if it is left attached to the device A Preparation Table of continuous Recording Time based on Model and Battery Type If you close the LCD screen it switches off and the Viewfinder switches on automatically The continuous recording times given in the table below are approximations Actual recording time depends on usage Battery Charging time Continuous recording time LCD ON VIEWFINDER ON SB LSM80 SB LSM160 AD43 00148A Notes Approx Thr 20min Approx Thr 20min Approx 2hr 40min Approx Thr 30min The Battery pack should be recharged in an environment between 32 F 0 C and 104 F 40 C The Battery pack should never be charged in a room with a temperature that is below 32 F 0 C The life and capacity of the Battery pack will be reduced if it is used in temperatures below 32 F 0 C or left in temperatures above 104 F 40 C for a long period of time
119. vanced Recording Using Quick Menu White Balance Quick menu is used to access Camcorder functions by using the Menu selector Quick menu provides easier access to frequently used menus without using the MENU button Press the Menu selector Move the Menu selector to the left or right to select White Balance then press the Menu selector Move the Menu selector to the left or right to select desired mode Auto Hold Indoor or Outdoor then press the Menu selector To exit press the MENU button Notes When NITE PIX is set to ON the White Balance function does not work SC D352 D354 D355 only The White Balance function will not operate in EASY Q mode Turn the Digital Zoom off if necessary to set a more accurate white balance Reset the white balance if lighting conditions change During normal outdoor recording setting to Auto may provide better results S STBY 0 00 10 S 60min Program AE White Balance Shutter Exposure Manual Focus A Gi STBY 0 00 10 f 60min DIS Program AE a TE A Balance Auto v Shutter Exposure Manual Focus WI Exit m gt kJ S 0 00 10 60min STBY lt When the Outdoor option was selected gt Advanced Recording Setting the Digital Image Stabilizer DIS The DIS function works only in Camera mode DIS Digital Image Stabilizer is a function that compensates for any sh
120. ve recorded on the LCD Screen Adjusting the LCD Bright Color during Playback Controlling Sound from the Speaker Tape Playback utc Playback on the LCD Screen Playback on a TV Monitor Connecting to a TV which has Audio Video Input Jacks Connecting to a TV which has no Audio and Video Input Jacks Playback Various Function Playback Pause Picture Search Forward Reverse Slow Playback Forward Reverse SC D354 D355 only Frame Advance To play back frame by frame SC D354 D355 only X2 Playback Forward Reverse SC D354 D355 only uT4 Reverse Playback SC D354 D3655 only 74 Zooming during Playback PB ZOOM AV In Out SC D355 only eee Audio Dubbing SC D354 D355 only Dubbing Sound 0 Dubbed Audio Playback EEE 1394 Datastranistercciccts ncn oe ete ee a oY USB Interface SC D352 D353 D354 D355 OMY sssssssssssssssesssseessssssssssssssssssssessssssssessessnsssssesssssssssssscsesssssessesssees OL Digital Still Camera Mode SC D353 D354 D355 Only ssssessessssssssessnsesssssssesssensesssssessessssssesesssssssescssssssssseseseensees OF Memory Stick Optional Accessory rrean actin can ts endian canteen AOE REPRE A E EAE T O 87 Memory Stick Functions Inserting and Ejecting the Memory Card Structure of Folders and Files on the Memory Card Image Format ccc eeeeeseeseeseeeeeseeseeeeees Selecting the Camcorder Mode Selecting

Samsung SC-D352 Camcorder User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents