RoadPro D3209 Security Camera User Manual
Contents
1. operate correctly You ve tried the suggestions but the 1 Contact your installer or dealer system is still not working 2 If they are unable to fix the problem contact RoadPro _ P a _ _ wa 30cm Sat d l sira Spot beam C m a x O m O Astra 2 north D Astra 2 south J Eutelsat 28A amp Astra 1N European beam 2 This map is for guidance only and is neither a represen tation of satellite footprints nor a guarantee of satellite reception It is based on information en 140cm Sat dome O Astra 2 north y D Astra 2 south Eutelsat 28A amp Astra 1N uropean beam 2 ED D aN x 4 7 f f K all gt ae Kg cf i is p E Auto skew will significantly improve the chances of receiving a good signal in areas away from the centre of the footprint areas shown Distributed in the U K by RoadPro Ltd Unit 7 Stephenson Close Daventry Northants NN11 8RF Tel 01327 312233 E mail sales roadpro co uk www roadpro co uk Practical Products on the Move 4 Powered by Wi WOrIC 3 ROADPRO a amp Powered by Wi wo rie om ROADPRO n Wiwork Installation and instruction manual for static RoadPro sat domes D3201 2 30 40cm static sat dome D3205 6 30 40cm static sat dome with twin LNB D3209 10 30 40cm static sat dome with auto skew D3211 12 30 40cm static sat dome with twin LNB auto skew Thank you f2. connected to the receiver and is switched to the appropriate source To switch the system on Press the red button on the left of the controller The system will immediately begin searching for the selected satellite the one with a corresponding red LED illuminated It may find a different satellite first and then after calculating its position move to the chosen satellite and lock on This can take between 10 60 seconds depending on how far the system is from where it was when it was last used Fine tuning will then be carried out and shortly afterwards a picture will appear on the TV or monitor When the satellite has been found and you can see a picture on the screen you can turn the controller off using the red button The dish will remain in position until the next time you turn the controller on To select a different satellite The controller enables you to select a number of satellites Astra 2 Astra 1 Hotbird Sirius 4 8 Astra 4 Hispasat and Atlantic Bird 3 To select a different satellite from the one currently selected tap the white button on the controller This will cause the illuminated LED to move along the row of marked satellites When the satellite you want is illuminated stop tapping The system will now search for that satellite and will return to the same satellite the next time you turn the system on after you have turned it off Make sure you ve selected the same satellite on your rece
3. controller and the short cable supplied to the connector marked RECEIVER Connect the other end of that cable to your satellite receiver The installation is now complete and you can connect a TV to the receiver turn everything on and use your sat dome for the first time Very important Please read this It is essential that your sat dome is installed using the cables supplied and that these cables are not cut or modified in any way If any other cables or connectors are used or if the cables are cut the system will not work correctly This applies to both original and secondary installations 2 BASIC OPERATION The RoadPro sat dome controller has a red on off switch and a white satellite selector button These control all operational functions of the sat dome Three LEDs show the status of the sat dome and a ROADPRO seven other LEDs show which satellite is being on mewn T T searched for or has been located The controller is re set for Astra 2 south when it is first delivered and other satellites can be chosen as required Astra 2 is the satellite which carries all TV and radio channels intended for viewing and listening in the U K Before attempting to operate the system make sure that the controller is connected to a 12V 24V power supply and that a suitable receiver is also connected Make sure that the receiver is set to work with the same satellite that you want the sat dome to find and that a TV or monitor is
4. If something seems to be not working properly uN ROADPRO n Wiworke aN ROADPRO 2 Wiwork If the red satellite indicator lights chase along the If the POWER LNB amp LOCK lights come on row the selected satellite cannot be found together POWER amp LOCK will blink check the Check for obstructions such as trees amp buildings cable between controller amp sat dome Symptom What you should do The control box does not power up 1 Check the power supply 2 Switch the control unit off and on again The system seems to operate 1 Make sure that the dish has a clear view of the satellite correctly but no satellite is found avoid trees buildings pylons etc 2 Check cables and connections 3 Switch the control unit off and on again A satellite is found but there s no 1 Check that you have selected the correct satellite and that picture on your TV your receiver is set for the same one 2 Check that cables and connectors between the sat dome controller the receiver and the TV are all secure You can see a picture onthe TVbut 1 Check that there are no obstructions between the dish and itis breaking up the satellite If you are near the edge of the 2 Check all cables and connectors satellite s transmission area footprint this can happen The TV has sound but no picture 1 Check that you have not selected radio on your receiver instead of TV 2 Check that the power to your TV is sufficient for it to
5. iver What the LEDs mean ON ROADPRO j F Wiiware f POWE on ROA DPRO F wy Wiiware I System set to search for Astra 2 south System has found a satellite and will now move to Astra 2 south LNB on ROADPRO Di L PN 7 Powers ty Wivvoric 7 POWER r ROA DPRO Wiworic T System has confirmed that the selected satellite Astra 2 south has been found and has locked on Turn off power switch Astra 2 south LED blinks once the selected satellite has been found 3
6. or buying a RoadPro sat dome To enable us to provide the best after sales service please make a note of the unit s serial number which you will find above the external cable connecting socket DELIVERY RoadPro sat domes come with the following parts in the box Sat dome Control box incl power supply 1 HQ co ax cable 10m with F plugs 2 cables are supplied with twin LNB models Installation and usage instructions 1 HQ co ax cable 1m 1 Cable entry box 12 screws 3 in dome cover 9 in bag INSTALLATION We strongly recommend getting the sat dome fitted to your vehicle or boat by a professional installer Preparation 1 2 10 11 12 Ensure that the roof of your vehicle is able to carry the sat dome If you are not sure check with your dealer or the vehicle s manufacturer Check that you have all the parts that are listed above Find a suitable place on the roof of your vehicle to mount the sat dome The sat dome s external cable connector must face towards the rear of the vehicle The mounting place must be level and even Mark the outline of the sat dome s feet with a pencil Ensure that the underside of the mounting feet and the area of the roof where they will sit is clean and dry If necessary clean with a suitable cleaning agent Methylated spirits works well on most surfaces and with many adhesive sealants If in doubt test the surface first and consult the manufacture
7. r of the sealant adhesive It may be necessary to roughen the underside of the feet and the fixing area on the roof follow the instructions that came with the adhesive sealant and then apply it evenly to the underside of the mounting feet The minimum thickness of the adhesive layer must be at least 2mm Within 5 minutes of applying the adhesive replace the sat dome on the roof in the pre selected position Press the feet onto the roof and trim off any excess adhesive It is essential that you give the adhesive enough time to harden completely The time this takes will vary according to the adhesive used and the ambient temperature and humidity Always follow the instructions that come with the adhesive sealant and if you are in any doubt as to how it should be applied seek professional advice We strongly advise screwing the mounting feet to the roof after the adhesive has been applied At this point you should remove the cover of the dome cut the cable tie and remove all packaging Replace the cover with the screws supplied Use the cable entry box supplied to take the 10M cable from the sat dome through the roof to the controller Ensure that the cable is secure and cannot be caught by obstacles Install the controller in a convenient position inside the vehicle and using the power cable supplied connect to a reliable 12V or 24V power source Connect the cable from the sat dome to the connector marked ANTENNA on the back of the
Download Pdf Manuals
Related Search