Roadmaster VRCD220S Car Stereo System User Manual
Contents
1. 1 Turning the Unit On Off Press any button to turn the unit on WELCOME will be displayed on the LCD to indicate it is ready for use Press and hold the POWER button to turn the unit off 2 Mode Selection Press the MODE Button to cycle between AUX RADIO and CD modes 3 Volume Use the VOL Buttons to adjust the vol ume level The higher the VOL number the higher the volume level 4 Bass Press the SEL Button until the display shows BAS Use the VOL Buttons to adjust When DSP is ON the Bass control is not available 5 Treble Press SEL Button until the display shows TRE Use the VOL Buttons to adjust When DSP is ON the treble control is not available 6 Balance Press SEL Button until the display shows BAL then use the VOL Button to adjust the balance between the left amp right speakers 7 Fader Press SEL Button five times and the display shows FAD then use the VOL Button to adjust the balance between the front amp rear speakers 8 Clock 1 While listening to the radio press the CLK button until the clock is dis played 2 Press and hold the CLK button until the time starts to flash 3 Press the VOL Button to adjust the hour 4 Press the VOL button to adjust the minutes 5 Press the CLK button again or just leave the the unit idle for a few new set tings to take effect VRCD220S English PRO2. Seek Function Press and hold the gt gt Button for about 2 seconds and the radio will search forward for the next strongest frequency then stop 3 Press and hold the lt lt Button for about 2 seconds and the radio will search backward for the next strongest frequency then stop 3 Save Your Preset Stations VRCD220S English PROOF Manual indd 11 10 There are six numbered preset buttons which can store and recall stations for each band While listening to a radio station you would like to save as a pre set press and hold one of the buttons numbered 1 6 until you hear a beep The button you pressed is now the pre set button for that station 4 Automatic Store Preset Scan A Automatic Scan amp Store While listening to the Radio press and hold the F PS Button The receiver will automatically scan all of the frequencies of the band you are tuned to After scanning the frequencies it will auto matically store the strongest signals to the pre set buttons If there are any stations already saved to the pre set buttons they will be replaced by the Automatic Scan amp Store function B Scan Saved Stations Press the F PS button once to perform the scanning functions In FM mode press the F PS button and the stations in all 3 FM bands will be scanned press this but ton in AM mode and scan all 2 AM Band Stations RDS Operation Enhanced Other Networks EON This unit is equipped with the la
3. Skip Protection is ideal for driving on rough roads Electronic Skip Protection for MP3 amp WMA CDs is a default feature Please note that this feature sup ports CDs with Songs encoded by 96Kb s and 32000Hz For songs encoded in higher quality the anti shock duration will decrease propor tionally to the file size 1 Insert Eject CD Insert a disc with MP3 into the CD slot with label side up The disc will be automatically loaded into the unit even when it is off or in radio mode The word MP3 DISC will be displayed as the CD is loaded The first file in the root folder will be played As the file is playing ROOT will be displayed first then the if there is any ID3 information that will be displayed as the file is playing Press the EJECT Button to eject the disc from the slot If the disc is not removed from the slot within 5 seconds it will automatically be loaded into the slot again When the disc is ejected and removed the unit will automatically switch to radio mode 2 Selecting Tracks On the Head Unit press the gt gt Button to advance CD to the next track Track num bers will be shown on the display Press and hold the gt gt Button to fast forward The disc will play normally when the gt gt Button is released Press the lt lt Button to go to a previous track The track num bers will be shown on the display Press and hold the lt lt Button to fast r
4. TA TP is displayed and the alarm is turned off TP Traffic Program The TP Function is used to allow the user to find only those stations that regularly broadcast traffic bulletins PTY Program Type This PTY function allow you to select the type of program you wish to listen to and will search for a station broadcasting that type of program Press the PTY button once to show the music type Then press the 1 6 buttons to choose the different music types available Press the PTY button twice to show Talk Show programing you can search for then press a number button 1 6 to choose a different Talk Show type program Each number button can display 3 Talk Show programs for you to choose There are up to 31 pre defined program types that allows users to find programing by genre MASK DPI MASK ALL Press the SEL Button for 2 seconds the display will show TA SEEK Press the 11 sound select button again so that the unit will show MASK DPI Press the Buttons to toggle between MASK DPI and MASK ALL mode Then leave the unit idle for the new setting to take effect During MASK DPI mode the unit will mask only the AF which has differ ent PI this is the default mode during MASK ALL mode the unit will mask the AF which has different PI and no RDS sig nal with high field strength RETUNE S L SHORT LONG This function is to
5. the display will show TRK SCH Press the SEL Button so 10 15 08 11 34 19 AM LL _ S6W T j MP3 amp WMA Disc Operation that TRK will blink on the display Then use the VOL Button to choose your desired track and press the SEL Button again to confirm the selection The selected track will be searched for and then played 3 File Search Press the F PS Button twice and the display will show FILE SCH Press the SEL Button to enter the root folder of the disc Use the VOL Button to choose a folder in the root folder then press the SEL Button to confirm The selected folder will be opened 4 Character Search Press the F PS Button three times and the display will show CHAR SCH This is for files by file names Press the SEL Button and the first character will blink on the display Use the VOL Button to change the character Press the SEL but ton once to confirm the character entered and advance to the next character After you have input the name press and hold the SEL Button to confirm The song near est alphabetically to the name input will be found and then begin to play AUX IN amp RCA Output 1 Auxiliary Input The Auxiliary Input RCA Jacks are on the rear of the unit To use the AUX IN feature you must use a RCA to 3 5mm cable Insert the cable s RCA plugs into the Red amp White AUX IN jacks on the rear of the unit Route the end of the cable with the 3 5mm
6. 20KHz Channel Separations ienero ear reae ANN Ait nna end gt 50dB DPA COMVOMEN secs aces cosde cates voaseaaceedaescexaavecbensse Gesssseoxessexesaccecnadeenssaieereacsdeesiea ddssiiacaasdas 1 Bit FM TUNER Tuning Range ccceceeeseeeeeeeeeeees USA 87 5 107 9MHz Europe 87 5 108 MHz FMS6nSitiVitys aii ich nna naan hal Nal aac alin ave 12dBu Stereo Separation 1 KAZ sie ccscsigcavensce ch cenaseesdcactgastdacerasaneadeusd aa anar naaa ANAE Edi 35dB AM TUNER Tuning Range ceeeee USA 530 1710 KHz Europe 522 1620 KHz AM SOMSIUIVILY scetecivae evinces ies aa aaaea ee aver Witenes bird ania 30dBu VRCD220S English PROOF Manual indd 16 D 10 15 08 11 34 19 AM ZZ G a Ts Limited Warranty VIRTUAL REALITY SOUND LABS products are designed and manufactured to provide a high level of trouble free performance VIRTUAL REALITY SOUND LABS warrants to the original purchaser that its products are free from defects in material and workmanship for 30 days from the date of original purchase as part of our commitment to product excellence VIRTUAL REALITY SOUND LABS and or it s affiliates routinely improves the designs materials or production methods of its existing products Because it is impractical to publicize all changes in every product we reserve the right to make such changes without notice CONDITIONS OF WARRANTY If during the 30 day warranty period your new product is found to be defectiv
7. Asti VRCD220S CD MP3 WMaA Player AM FM Stereo Receiver with RDS Auxiliary Input and Detachable Face VRCD220S English PROOF Manual indd 1 D 10 15 08 11 34 09 AM Welcome Dear Customer CONGRATULATIONS The VRCD220S CD MP3 WMA Player AM FM Stereo Receiver with RDS Auxiliary Input Detachable Face and Speaker Kit when used as described will give you years of dependable service in your car truck RV or mini van We have taken numerous measures in quality con trol to ensure that your product arrives in top condition and will perform to your satisfaction In the rare event that your VRCD220S CD MP3 WMA Player AM FM Stereo Receiver with RDS Auxiliary Input Detachable Face and Speaker Kit contains a damaged or missing item does not perform as specified requires warranty service or you have an installation problem DO NOT RETURN THIS PRODUCT TO THE STORE PLEASE CALL OUR TOLL FREE NUMBER FROM THE U S A AND CANADA 1 800 445 1797 and ask to speak with a member of our technical service team or submit your ques tions by e mail to customerservice vr 3 com and a member of our technical service team will respond by e mail to your questions Our in house technical service team will expedite delivery of your part advise you on installation or help troubleshoot a problem with you If your product needs warranty ser vice our technical service team representative will help you obtain the fastest remedy possible under the wa
8. G18 or more automotive grade cable to avoid wire deterioration or damage to the wire coating e To prevent short circuit never put or leave any metallic object inside the unit If you smell or see smoke turn off the power immediately and consult your dealer e Insert the unit until it is firmly locked into mounting sleeve otherwise it may fall out e Be careful not to drop or shock the unit it may break or crack because it contains glass parts e The unit is only designed for use with 4 speakers Do not combine output for use with 2 speakers Do not ground negative speaker leads to the chassis ground e Do not open the top or bottom cover and do not install the unit in a place where it is exposed to direct sunlight including faceplate high heat humidity moisture or dust e The faceplate is a precision piece of equipment that contains sensitive electronic com ponents Do not subject it to excessive shock e When replacing the fuse s the replacement must be of the same amperage as shown on the fuse holder e Do not block vents or heater panels Blocking them will cause heat to build up inside and may result in fire e After completing the installation and before operating the unit reconnect the battery Then press the RES button with a pointed object such as a ball point pen to set the unit to its initial status e Do not touch the terminals of the faceplate or of the unit e If you have difficulty installing this unit in yo
9. OF Manual indd 10 9 DSP Preset Equalizer Function 1 Press and hold the SEL button until you hear a beep 2 Press the SEL button to cycle through the menu choices until you see DSP OFF 3 Press the buttons to cycle through the pre set EQ settings ie DSP OFF gt POP M gt ROCK M FLATM CLASS M al 4 Leave the unit idle for the new setting to take effect 10 Loudness 1 Press and hold the SEL Button until you hear a beep 2 Press the SEL Button until the display shows LOUD OFF 3 Use the Buttons to select LOUD ON Loudness effect ON or LOUD OFF Loudness effect OFF 4 Leave the unit idle for the new setting to take effect 11 Preset Beep Sound Off 1 Press and hold the SEL Button until you hear a beep 2 Press the SEL Button until the display shows BEEP ON 3 Use the Buttons to select BEEP ON beep sound on or BEEP OFF beep sound off 4 Leave the unit idle for the new setting to take effect 12 Preset Volume Level You can set the default volume level for the unit when it is turned ON 1 Press and hold the SEL Button until you hear a beep 2 Press the SEL Button until the display shows VOL LAST 3 Press the Buttons to enter VOL ADJ will be displayed 4 Press the SEL Button and A VOL 15 will be displayed The number after A VOL indicates the volume leve
10. arranty service we request that you adhere to the following procedure 1 Include a copy of your sales receipt or bill of sale with your unit when it is returned for warranty service D 2 If it is necessary to return your product for service please return it securely packed preferably in the original amp shipping carton and freight and insurance prepaid to the following address VIRTUAL REALITY SOUND LABS Service Department 41 James Way Eatontown New Jersey 07724 3 Please include a detailed explanation of the problem you are having 4 If your product is found by VIRTUAL REALITY SOUND LABS to have a defect in material or workmanship within the warranty period it will be repaired or replaced at no charge and returned to you prepaid Where permitted by law VIRTUAL REALITY SOUND LABS liability shall be limited to that set forth in this warranty This warranty shall be the exclusive remedy of the purchaser VIRTUAL REALITY SOUND LABS makes no other warranty of any kind expressed or implied and all implied warranties are hereby disclaimed by VIRTUAL REALITY SOUND LABS and excluded from this warranty VIR TUAL REALITY SOUND LABS and or its affiliates the manufacturer distributor and seller shall not be liable for any injury loss or damage incidental or consequential arising out of the use or intended use of the product VRCD220S English PROOF Manual indd 17 D 10 15 08 11 34 19 AM 2008 Intellectual Solutions Inc All rights reser
11. e VIRTUAL REALITY SOUND LABS will repair such defect or replace the product without charge for parts or labor subject to the following condi tions 1 All repairs must be performed by VIRTUAL REALITY SOUND LABS and or its affiliates in Eatontown New Jersey 2 The equipment must not have been altered or been damaged through negligence accident or improper opera tion 3 The replacement of parts are exempted from this warranty when replacement is necessary due to normal wear and tear 4 All warranty claims must be accompanied by a copy of the sales receipt or bill of sale 5 Repair or replacement parts supplied by VIRTUAL REALITY SOUND LABS under this warranty are protected only for the unexpired portion of the original warranty 6 In the case of car stereos this warranty does not extend to the elimination of car static or motor noise cor rection of antenna problems costs incurred for the removal or reinstallation of the product damage to tapes speakers accessories or car electrical systems 7 VIRTUAL REALITY SOUND LABS will not be responsible for any charge incurred for installation OWNER S RESPONSIBILITIES VIRTUAL REALITY SOUND LABS will make every effort to provide warranty service within a reasonable period of time SHOULD YOU HAVE ANY QUESTIONS ABOUT SERVICE RECEIVED OR IF YOU WOULD LIKE ASSISTANCE IN OBTAINING SERVICE PLEASE CALL TOLL FREE 1 800 445 1797 8 30am 4 30pm EST In order to provide you with the proper w
12. everse Disc will play normally when the lt lt Button is released On the Remote Control the lt lt or gt gt Buttons operate the same as on the Head Unit VRCD220S English PROOF Manual indd 14 13 4 Play Pause CD On the Head Unit press the No 1 Button to pause the CD Press this button again to resume playback 5 Scanning Tracks On the Head Unit press the No 2 INT Button to play the first 10 seconds of each track Press this button again to resume playback 6 Repeat On the Head Unit press the No 3 RPT Button to repeat the same track continu ously RPT ON will appear on the display Press this button again to stop repeating 7 Random On the Head Unit press the No 4 RDM Button to play all the tracks in random order RDM ON will appear on the dis play Press this button again to stop ran dom play 8 UP 10 Press the No 6 UP10 Button to advance 10 track at a time 9 DN 10 Press the No 5 DN10 Button to go back 10 track at a time Search Modes There are 4 search modes to help find your favorite MP3 tracks The search modes only works with MP3 CDs and do not work with any other type of CDs 1 Simple Track Search Press the SEEK lt lt or gt gt Button to go to the next track or previous track Press the Number 5 button to go back 10 tracks at once or press the Number 6 button to advance 10 tracks at once 2 Track Search Press the F PS Button and
13. jack to an area that is safe and convenient to the headphone jack of any external audio device such as walkman and disc man Press the Mode button to choose AUX Connect any portable audio device such as a DVD player or VCD player to the VRCD220S English PROOF Manual indd 15 14 AUX IN cable Use the volume control to adjust volume 2 RCA Output The RCA Output Jack is on the back of the unit Refer to Wiring Diagram This output is for connecting amplifier equalizer or other audio component that requires a pre amp out connection Red Right White Left Follow the manufacturers instructions for the audio component that you are con necting Maintenance Cleaning the Unit Do not use any liquids to clean this unit Do not use petroleum distillates to clean this unit Use a clean dry cloth to clean this unit Replacing the Fuse Make sure the amperage matches the specified value when replacing the fuse s If the fuse is bad check the power connec tion and replace the fuse with a new one If the same problem occurs this might indi cate a malfunction within the unit Warning When replacing a fuse do not use a fuse with a higher amperage rating than the fuse originally supplied to your unit other wise damage will result to your unit 10 15 08 11 34 19 AM ZAZA e a Ts Simple Troubleshooting Guide PROBLEM CAUSE SOLUTION No Power Check wiring connections Check and make sure the fuse is no
14. l indd 8 D Green White l E Left Front Brown Brown White Grey Grey White l Right Front Blue Blue White s Left Rear Right Rear Visit us on the WEB 1 800 445 1797 GIVE US A CALL WE LL HELP YOU INSTALL PLEASE DO NOT RETURN PRODUCT TO STORE www vr 3 com For Information and Technical Assistance Call Toll Free in U S A and Canada 10 15 08 11 34 15 AM MENEE O Oe Location of the Controls 21 20 1918 17 16 15 14 13 12 11 10 9 1 Clock Button 14 Pre set 5 Down 10 2 Mode Button 15 Pre set 4 Random 3 Volume Up Button 16 Pre set 3 Repeat 4 SEL Button 17 Pre set 2 Intro 5 PTY Button 18 Pre set 1 Pause Play 6 LCD for Track Number Time Radio 19 TA Button Frequency File Type ID3 RDS EQ 20 Volume Down Button 7 Open Faceplate Button 21 AF Button amp 8 Next Track Change Frequency Fast Forward 22 Eject button 9 Previous Track Change Frequency Fast Reverse 23 Reset button 10 Band Button 24 Americas Europe Switch 11 F PS Button 25 Disc Slot 12 Power Button 26 Red LED 13 Pre set 6 Up 10 22 23 24 25 26 To Remove the Faceplate 1 Press the Open Button to open the faceplate 2 Tilt the faceplate down about half way and push the faceplate to the left then pull the it towards you to remove it VRCD220S English PROOF Manual indd 9 D 10 15 08 11 34 16 AM Basic Operation
15. l the unit will default to the next time you turn the unit ON 10 15 08 11 34 18 AM LL __ d6 T j Radio Operation E 5 Press the Buttons to adjust the vol ume level 6 Leave the unit idle for the new setting to take effect The next time you turn the unit ON the volume will automatically be adjusted to the sound level you set here Radio Frequency Selection The default frequency setting is in your country mode However if you want to change the frequency to Europe or USA please follow the step below 1 Press the Open Button to open the faceplate 2 Tilt the faceplate down about half way and push the faceplate to the left 3 Pull the faceplate towards you to remove it 4 Below the faceplate you will see a switch with the letter A on the right side and the letter E on the left side 5 For use in the Americas slide the switch to the left or for use in Europe slide the switch to the right 1 Choose a Radio Band The unit comes with five bands for storing your favorite radio three FM Bands FM1 FM2 and FM3 and two AM Bands AM1 and AM2 selects Each of the five bands can store up to six preset stations for a total of 30 preset memory stations 18 FM Pre sets and 12 AM Pre sets 2 Manual Tune Seek Function Manual Tune Press the gt gt Button to adjust the radio to a higher frequency or press the lt lt Button to adjust the radio to a lower frequency
16. n the grooves on both sides The unit can be installed or removed from the dashboard using these keys Fig 3 D 10 15 08 11 34 14 AM MEENE e Oe Installation DIN REAR MOUNT Method B Installation using the screw holes on both sides of the unit 1 Screw holes on the side of the unit 2 Screws Use either truss screws 5 x 8mm or flush surface screws 4 x 8mm depending on the shape of the screw holes in the bracket 3 Vehicle s Factory Mounting Bracket 4 Dashboard or Console 5 Hook Remove this part Note The mounting sleeve outer trim amp ring and the mounting strap are not used for this method of installation PARTS 2 Keys 1 Hex Nut 2 Lock Washers 1 Sheet Metal Screw 1 Metal Support Strap 2 Flat Washers 1 Mounting Bolt 1 Faceplate Case 1 Faceplate not shown VRCD220S English PROOF Manual indd 7 D 10 15 08 11 34 14 AM Installation WIRING CONNECTIONS AUXIN RCA OUT Right Red Right Red ANTENNA Left White ie OCKET Left White Dashboard Light Dimmer Switch Amplifier Remote or Power Antenna 10 Amp Fuse Yellow memory Black ground 1 Amp Fuse Ignition Key Red 12V VRCD2208 English PROOF Manua
17. not removed from the slot within 5 seconds it will automatically be loaded into the slot again When the disc is ejected and removed the unit will automatically switch to radio mode 2 Selecting Tracks On the Head Unit press the SEEK gt gt Button to advance CD to the next track Track numbers will be shown on the dis play Press and hold SEEK gt gt to fast forward Press the SEEK lt lt Button to go to a previous track Track numbers will be shown on the display Press and hold the SEEK lt lt Button to fast reverse Disc will play normally when the SEEK gt gt or SEEK lt lt Button is released On the Remote Control use the lt lt or gt gt Buttons 3 Play Pause CD Press the No 1 Button to pause the CD VRCD220S English PROOF Manual indd 13 12 Press this button again to resume play back 4 Scanning Tracks Press the No 2 INT Button to play the first 10 seconds of each track Press this but ton again to resume playback 5 Repeat Press the No 3 RPT Button to repeat the same track continuously RPT ON will appear on the display Press this button again to stop repeating 6 Random Press the No 4 RDM Button to play all the tracks in random order RDM ON will appear on the display Press this button again to stop random play 10 15 08 11 34 18 AM MP3 amp WMA Disc Operation MP3 amp WMA Disc Operation Electronic Skip Protection 120 Seconds Electronic
18. rranty Contents PRECAUTIONS dcsxccsss cence foane aaae a ia sash coins aaah deen eens E E a 2 Notes oni Installationisecssi a det atin erent cee ees 3 Before You Install sic ivsezececcieds fue sgees stock aea enaa ae Eaire aaea 4 Installation DIN Front MOUND sorea a a ea E 5 Installation Vehicle s Brackets aissa iiaa e a aaa Eiaa 6 Wining CoOnNeCtiON Seseme ona a ao ae T Location Of Control Sis csicec ceiass daecedecasusete dh acdasasaegeestabdsesedechsthedeadchsadusneoessansastaed 8 Basic Operation sis tnana aa aa aeren 9 Radio Operations anar device n eN a N a 10 RDS Operaatio Nuera e a a aia a da aeeai Aa adele 10 11 CD Operation s asies necia oiana raare anie nerina anea aae ea asata N naiai iaae 12 AUX IN RCA QU wa sevecictes cence azsdeuts eoeaccdvahiacsieasavedes deans chadesladhaeelbeateivase cneseactels 14 Maint GM AN CEs aa eaaa aaaea ea dave nen iae a dana haa aaae aa ede eee 14 Simple Troubleshooting Guide ceecceeseeceseeeseeceseeeeeeteaeeseaeesaeeseaeeeseeeaes 15 SPSCIPICAL ONS i iae a aae dn che aaa a aa raa a a Aa e A Pa a EAA Eaa E aa 15 Warranty eao ae A a E ote 16 VRCD220S English PROOF Manual indd 2 D 10 15 08 11 34 12 AM M1 a Precautions This unit will only play the following discs Type of disc Label on the Disc Recorded Material MP3 WMA N A Audio only 12 cm e Do not attempt to modify the unit e Do not operate in extremely high or low tem e Modifying the unit will
19. set the initial duration of automatic TA Search Press and hold the SEL button until TA SEEK is shown on the LCD then Press the Buttons to cycle through the menu selec tions until RETUNE_S is shown use the VOL button to choose RETUNE_S or RETUNE_L The default is RETUNE_S 10 15 08 11 34 18 AM CD Operation Electronic Skip Protection 12 or 45 seconds Electronic Skip Protection is ideal for driv ing on rough roads Press the SEL Button until the display will show TA SEEK Then press the SEL Button to cycle through the menu until ESP12 is displayed indi cating that 12 seconds Electronic Skip Protection will be activated With ESP 12 on the display use the VOL Buttons to change the setting to ESP 45 indicating that 45 seconds Electronic Skip Protection is activated Leave the unit idle for the new setting to take effect 1 Insert Eject CD Insert a disc with MP3 into the CD slot with label side up The disc will be automatically loaded into the unit even when it is off or in radio mode The word MP3 DISC will be displayed as the CD is loaded The first file in the root folder will be played As the file is playing ROOT will be displayed first then the if there is any ID3 information that will be displayed as the file is playing Press the EJECT Button to eject the disc from the slot If the disc is
20. t blown Replace with the proper rating size fuse Some errors occur in the LCD or Press the RESET Button nothing functions when buttons are pressed Unable to receive stations Check and make sure the antenna is con nected properly Poor radio reception Check and make sure the antenna is the correct length Make sure the antenna is not broken If the antenna is broken replace it The antenna is poorly ground ed Check and make sure the antenna is grounded at mounting location CD s cannot be loaded ACD is already loaded in the player Eject CD Songs keep skipping The CD is dirty or damaged File information shows in LCD but Your file may be corrupt will not play D Specifications GENERAL Operating POW6is c snide 11 to 16 Volts DC Negative Ground Total Maximum POWer spesies ia aineenaan ana raana a aara araa eaaa aaia Fe AE Aa AEAN 140 Watts RMS POW Gl issia a eaaa 4x7 Watts at 4 Ohms lt 1 THD N Output WIPING sicicscecccccaceccstscduvencecasciaansvectennterechess Designed for using four speakers only RCA INE OU ranna fiver dain N low level outputs 1000MV Output IMPE daN Esineiden iadaaa ana Compatible 4 to 8 Ohm Speakers FUSES ae a a a EEE EE E ee At 1 amp and 10 amp Dimension Senise ewe aaa a a et hs 178mm W x 178mm D x 51mm H Weightman narn dR een ee ee ees 2 3 Kg CD PLAYER Signal NOISE RatiO is fetuaren ester eared gpa soa Geeta arate eee eae gt 60dB Frequency RESPONSE koroen eect ewes eed aaa aaa 20 Hz
21. test tech nology of EON control EON control allows the receiver to monitor other stations for traffic announcements while you are lis tening to the Radio or a CD If there are any travel announcements on a nearby local station then the receiver will tune to the station turn up the volume or inter rupt the playback of the CD for the dura tion of the announcement At the end of the announcement the radio will return to its previous state ready for the next announcement AF Alternative Frequencies Press the AF button and the unit will choose the strongest FM signal for the selected 10 15 08 11 34 18 AM VRCD220S English PROOF Manual indd 12 RDS Operation station This means you do not have to re tune the radio when driving between different transmitter coverage areas When AF is on it means RDS information is received when AF is flashing it means RDS information is not yet received TA Travel Announcements Press the TA button and the unit will be activated for reception of traffic announce ments from local radio stations To choose the TA mode press the SEL Button for 2 seconds the display will show TA SEEK Press the Buttons to choose between TA SEEK and TA ALARM after chooisng please leave the unit idle for the new mode setting to take effect In TA SEEK mode the unit will seek for traffic announcement program when TA is pressed in TA ALARM mode no
22. tly by checking Consult wiring diagram of existing head that the speaker wires are the same unit before disconnecting any wires Ifa at the head unit wiring diagram is not available contact 5 Repeat this procedure for all of the the manufacturer speakers 6 Mark the power ground and any 1 While the old unit is playing discon other wires also nect the wires from one speaker 2 Take a length of masking tape and fold it around the wire so it forms a flag 3 On the masking tape mark the polar ity of the speaker wires amp as VRCD220S English PROOF Manual indd 5 D 10 15 08 11 34 13 AM Installation DIN FRONT MOUNT Method A 1 Dashboard tosecurethe into the dashboard select tabs on Mounting Slee top bottom and sides then bend Ww Bend the tabs After inserting the Mounting Sleeve 2 Mounting Sleeve Follow the diagram in Fig 2 for in stalling the rear mounting strap to the head unit The rear mounting strap will help keep the head unit from moving around inside the dash board in the dashbo them to secure the mounting sleeve in the dash board Fig 1 1 6 7 ea ae 1 Dashboard 2 Nut 6mm 4 So 3 Spring washer ee 4 Screw 6 x e 25mm 3 w 5 Screw 6 Strap Fig 2 7 Plain washer Insert fingers into the groove in the front of frame to remove it a Fig 3 VRCD220S English PROOF Manual indd 6 Insert the keys supplied with the unit i
23. ur vehicle Please contact your dealer IMPORTANT Remove the half sleeve Remove the transport CD Stopper 2 screws before use VRCD220S English PROOF Manual indd 4 D 10 15 08 11 34 12 AM ZAZA G a Ts Before You Install Automotive audio equipment installations can be challenging at times even to the most experienced of installation technicians If you are not confident working with electrical wiring removing and reinstalling interior panels carpeting dashboards or other compo nents of your vehicle please call our toll free help line 1 800 445 1797 and our in house technical service team will answer your installation questions Contact the vehicle s manufacturer for vehicle specific instructions or consider having the VRCD220S profes sionally installed IMPORTANT Remove the two transport screws from the top of the unit before installing 1 Remove the Old Unit from the Dashboard A Remove the outer trim frame B Insert the keys supplied with the old unit into both sides of the unit as shown in figure below until they click Pull to re move the old unit from the dashboard 2 E DIN Front Mount DO NOT DISCONNECT WIRES AT THIS TIME 2 Mark Polarity of the Speaker Wires Marking the polarity of the speaker well as left or right and front or rear wires will make it easier to connect the 4 Double check that you marked the existing speakers to the VRCD220S first speaker correc
24. ved All designs logos and images are the exclusive property of Intellectual Solutions Inc and or its affiliates US and Foreign patents pending 072208 Printed in China 00000 VRCD220S English PROOF Manual indd 18 D 10 15 08 11 34 19 AM
25. void the warranty peratures The temperature inside the vehicle e Stop the vehicle before carrying out any oper should be between 32 F 0 C and 100 F ation that could interfere with your driving 37 C before turning on your unit Care of Discs e Do not use CDs with labels or stickers e Handle the disc by its edge to keep the disc attached The label may leave a sticky resi clean Do not touch the disc s surface due when it begins to peel ee Q t e Do not use a CD with paste or ink residue e Clean the discs with an optional cleaning on it cloth Wipe each disc from the center out VRCD220S English PROOF Manual indd 3 D 10 15 08 11 34 12 AM ZS G a T Notes on installation e Disconnect negative battery terminal before starting installation Consult the vehicle s owner s manual for proper instruction e The unit is designed for a 12 Volt DC negative ground operation system only Before installing the unit make sure your vehicle is a 12 Volt DC negative ground system e Mark the polarity of the existing speaker wires before disconnecting the old unit e Be sure to connect the color coded leads according to the diagram Incorrect connec tions may cause the unit to malfunction or damage the vehicle s electrical system e Make sure all the connections are completely correct before turning on your unit e When extending the ignition memory backup or ground cable use diameter of 0 75mm AW
Download Pdf Manuals
Related Search