Quatech ABDG-SE-IN5410 Server User Manual
Contents
1. CONNEGUT WIIN RELIABILITY Quick Start Guide AirborneDirect Industrial Serial Device Server ABDG SE IN5410 IN5420 Revision v2 1 February 2011 Document Number 100 8106 210 Kit Contents Upon receiving the kit please check that you received the following ABDG SE IN5410 or ABDG SE IN5420 Unit 2dBi 2 4Ghz 50 ohm omni directional antenna Quick Start Guide 5 VDC power supply optional included only if ordered as an accessory Airborne Direct software and documentation CD If any of the above contents are missing or appear damaged please contact Quatech Sales support directly at 800 553 1170 or support quatech com What you will need To evaluate the unit you will need the following components and facilities ABDG ET IN50X0 unit with included antenna attached Laptop or desktop system with an Ethernet port 5 36 VDC power for terminal block attachment or an AC power outlet for optional ABDG SE IN5410 IN5420 power supply 802 11b g network for testing the unit either AdHoc or Infrastructure Access Points mode The test network configuration must be known Required information will include O SSID Wireless network name O Security settings WEP WPA WPA2 etc o Security credentials passphrase key or certificates O Static IP address Subnet Mask and Gateway address if static IP addresses are used on the test network A web browser on the laptop top or desktop MS Explorer Firefox Opera and Chrome v4 0 a2. 8106 210 Airborne Device State Adapter is not powered Adapter is powered Adapter is not powered Adapter failed Power On Self Test POST and is not configured for wireless communication Adapter passed POST but is not configured for wireless network communication Adapter passed post and is configured for wireless communication Adapter is not powered Periodic Blinking Adapter is searching for a valid network Access Point that matches device s configuration IN l Adapter has successfully associated with an Access Point If Power LED is also Off then Adapter is not powered If Power LED is On then e No TCP session from WLAN or Ethernet interface has been established A TCP connection to the adapter has been established from the Wireless or Ethernet interfaces but no traffic has been detected 6 February 2011 Serial Port Pin Out Figure 2 DE 9 Connector Pin out Table 3 Serial Port Pin Definition No Connect RxD TxD No Connect GND No Connect RTS CTS No Connect Serial Port Defaults Settings BAUD Parity Stop Bits Data Bits Flow Control Serial Default Mode Input Buffer Size Bytes Serial Escape Mode Second Serial Port If you have purchased the ABDG SE IN5420 device it is possible to configure the second serial port using the web interface Repeat step 10 in the Getting Started section however select the Serial Port 2 Settings link and configure the a
3. Ethernet Settings WPA WPA2 Pre Shared Key PSK Wireless Routing Settings IP Address Parameters Ethernet Routing Settings WLAN DHCP Advanced Settings Ethernet DHCP U Confiquration File List Configuration Files Delete Configuration File Ethernet Subnet Mask Active Con tion Wireless LAN Security Type WPA PSK Enabled Disabled Ethernet Static IP Address 1921682100 255 255 255 0 User Contouration MC ration Factory C ration WPA Configuration QUATECH INC 1 330 655 9000 phone 1 800 553 1170 toli free 1 330 655 9070 sales fax Quatech l Contact us l Technical Support 2009 2011 Quatech Inc To configure the device for operation each field must be configured correctly The following steps should be taken to configure the device Note not all fields will be visible Table 1 Express Page Setup Navigation Bar Select Configuration Feature Link Select Express Setup Select Discovery OEM Device Name Select Radio Startup Mode 100 8106 210 You will see a group of fields under the banner of WLAN Parameters This step is optional If this is the first time the device has been configured this page will automatically be displayed This parameter allows you to name the device uniquely or group into a functional set When device discovery is used this name identifies the found device If you wanted to uniquely identify the device you could mark it
4. with a label e g Dev1 and then enter Dev1 in this field When the device is found it will identify itself as Dev1 Alternately you could indicate the type of equipment the device is attached to e g Haas TL 2 CNC Turning Center by giving the unit a name like Haas_TL_2 When discovered you can then identify the device you are accessing Enter the text string is you wish to change the default value This field is optional Select On from the drop down menu for the radio to operate 4 February 2011 AirborneDirect Serial Device Server Quick Start Guide Quatech Inc Step Description Select Wireless LAN Connection Type If you are using Access Points make sure this is set to Infrastructure from the drop down menu If you want to use AdHoc set this accordingly Additional settings may be required to fully configure for AdHoc mode Please refer to the User s Manual for details Select SSID Enter the name of the wireless network you wish to access This field is case sensitive Select Wireless LAN Security Type Select the security type the wireless network you wish to access is using Depending upon the option you choose you may have to enter additional information Once you have selected the security type the required inputs will be made accessible by un graying the fields that must be completed If the security type is not in the available selections more are available in the WLAN Security Settings page If you choose to use
5. ection TCP Connection COMM Off Green LINK Green Green POST Green Green POWER Blue Blue To use the adapter on the wireless network address all traffic to the IP address of the wireless interface of the ABDG SE IN5XXX This address is listed in the home page of the web interface 100 8106 210 3 February 2011 AirborneDirect Serial Device Server Quick Start Guide Quatech Inc Express Setup Configuration Page When the devices web interface is accessed for the first time an Express Setup page will be shown This page is designed to allow a quick device set up by presenting the most popular device configuration options in a single location For more advanced configurations the full set of options are available in the feature links left hand column The Express Setup web page will display the necessary fields based upon the selections made during configuration The Express Setup page looks like Figure 1 Figure 1 Express Setup Page CGUWATIEACIEI A DPAC TECHNOLOGIES COMPANY M Status MN Configuration Certificates A CONNECT WITH RELIABILITY 3 Network Y Maintenance Express Setup Current Values Express Setup Discovery OEM Device Name OEM Cfg1 WLAN Settings Radio Startup Mode Of WLAN Security Settings WLAN Parameters Network Settings Wireless LAN Connection Type Infrastructure v Serial Port Settings SSID Serial Port 2 Settings Connection Settings
6. ed as a serial device server Ethernet interface is in client mode this address is only used if the Ethernet DHCP is disabled or DHCP failed Default 192 168 2 100 Select Ethernet Subnet Mask This field defines the subnet mask used by the Ethernet interface When configured as a serial device server Ethernet interface is in client mode this mask is only used if the Ethernet DHCP is disabled or DHCP failed Default 255 255 255 0 Press Commit Button Saves changes to the device Optional Reloads the Express Settings page Select this is you have Press Reload Button further configuration options to change 100 8106 210 5 February 2011 AirborneDirect Serial Device Server Quick Start Guide Quatech Inc Optional Description Restarts the device After the device as rebooted it will attempt Press Restart Button to authenticate to the configured network As long as the network is in range the wireless interface will connect If the network is using DHCP then an IP address will be assigned to the WLAN interface and IP connectivity is possible over the WLAN network If the network is using static IP addresses it will be necessary to configure the network interface see the next step The web interface supports advanced configuration of the device through the additional pages available The following sections provide guidance on how to use these pages for specific configurations Table 2 LED Indicators 100
7. nagement State 2 Select Manage OEM Cfg1 3 Select Device OEM Cfg1 is Factory Default J Airborne Management Center The devices status will move to managed and the device will be displayed under the device type group it belongs too Right click the device and then 1 Select Connectivity Tools 2 Select Launch Web Browser for OEM Cfg1 J Airborne Management Center Locate CE Launch Web Browser for OEM Cfg1 Birk POST LED for OEM Opening web page shows adapter status Links to the available configuration options are identified in the left hand menu The top menu bar provides access to different operations that can be performed by the AirborneDirect device Please refer to the User s Manual for a full description of how to use the web interface Using Express Setup If this is the first time you have configured the device the Express Setup page will be displayed This page provides access to the critical configuration items needed to get the ABDG up and running quickly See Express Setup Configuration Page section for details on how to configure the device Please refer to the User s Manual for complete details on ABDG device configuration When the Reboot button is pressed the unit will restart and install new settings This may take 15 20 seconds Please refresh the web interface after the boot cycle has completed When configured correctly the LED pattern should match the following ABDG SE IN5XXX No TCP Conn
8. ppropriate parameters 9600 None 8 1 None Listen 1460 ON No Connect RxD TxD No Connect GND RxD No Connect No Connect TxD 9600 None 8 1 None Listen 1460 ON AirborneDirect Serial Device Server Quick Start Guide Quatech Inc T AUATECH CONNECT WITH RELLA BILITY 5675 Hudson Industrial Parkway Hudson OH 44236 Tel 330 655 9000 800 553 1170 support quatech com www quatech com 2010 2011 Quatech Inc All rights reserved 100 8106 110G 8 4 27 2010
9. re supported CAT5 Ethernet cable for connecting the Airborne device to the laptop or desktop Serial cable to connect Airborne device to host system AirborneDirect Serial Device Server Quick Start Guide Quatech Inc Getting Started 100 8106 210 Open the AirborneDirect packaging and locate the Install CD Place the CD in the CD DVD drive of the laptop or desktop you will be using to configure the AirborneDirect device Follow the on screen directions for installation of the appropriate device software and documentation Connect the Ethernet cable on ABDG to an Ethernet port on the laptop or desktop system Apply power to the ABDG SE IN5XXX The unit will boot and display one of the following LED patterns ABDG SE IN5XXX COMM Off LINK Off POST Orange POWER Blue Run the Airborne Management System application This was installed during the CD installation and a menu item will be found in the Airborne folder located in the programs directory of your system When the application opens the following dialog will be displayed bs Group Login Group Name users Group Password seee Ca ae Select Group Name manuf and enter Group Password dpac The AMC will load and discover the attached device J Airborne Management Center 2 February 2011 AirborneDirect Serial Device Server Quick Start Guide Quatech Inc Right Click the Unmanaged Device then 1 Select Change Ma
10. this page make sure you commit the changes you have already made before moving to the WLAN Security Settings page Select WLAN DHCP If your WLAN network uses DHCP to assign IP addresses to the wireless clients select Enabled from the drop down menu If you are using static IP addresses select disabled from the drop down menu WLAN Static IP and WLAN Subnet Mask will need to be entered Select Ethernet DHCP If the Ethernet network connected to the Ethernet port uses DHCP to assign IP addresses to the wired clients you should select Enabled from the drop down menu If you are using static IP addresses you should select Disabled from the drop down menu Ethernet Static IP and Ethernet Subnet Mask will need to be entered Important This field is only used if the Ethernet interface is set as a client default for Serial devices If set as a router the field is ignored See the User s Manual for a full description of configuring the unit as an Ethernet router Select WLAN Static IP This field defines the static IP address for the wireless interface This address is only used if the WLAN DHCP is disabled or DHCP failed Default 192 168 10 1 Select WLAN Subnet Mask This field defines the subnet mask used by the wireless interface This mask is only used if the WLAN DHCP is disabled or DHCP failed Default 255 255 255 0 Select Ethernet Static IP This field defines the static IP address for the Ethernet interface When configur
Download Pdf Manuals
Related Search