Q-See QSDB8209C Baby Monitor User Manual
Contents
1. 77 998 3440 Q See Tech Support in U S A Mon Fri 9 am 5 pm PST TEL 1 877 998 3440 x 539 E mail ts dpsi usa com Website www q see com2. User s Manual See MODEL QSDB8209C Digital LCD Baby Monitor and Wireless Camera Visit Us on the Web at http www q see com Rev 072208 Contents 1 Packing List 2 Diagram 3 Structure 4 Installation 5 Specifications 6 FCC and EU 1 Packing List 1 2 4GHz Wireless Camera x 1 2 2 4GHz Wireless Receiver x 1 3 Earphone x 1 4 Power Adapter for camera x 1 5 Power Adapter for receiver x 1 Note AA Batteries are not included 2 Diagram 3 Structure 3 1 Layout of Camera Antenna IR LEDs Alarm Switch _ Power Sense l On Off Learning Switch Battery Cover Power Channel Socket Switch 3 2 Layout of Receiver Battery Antenna Cover Earphone Power Socket g TFT LCD Channel Indicator 1 Slee Button A Channel Volume Button Switch Eliminate i Power Alarm ka On Off Button 4 Installation 4 1 Setting Up the Camera 1 Setup the camera in the desired location 2 Connect the camera to the adapter and then slide the power switch to the ON position Note This camera can also use dry batteries as a power source by loading 4 AA batteries into the battery compartment on the back of the camera with their polarities in the correct position The AC adapter will work instead of batteries after it is plugged in If the camera is not going to be used for a long period of time please unplug the adapter and r
3. emove the batteries The camera can run off of batteries for up to 5 hours IR OFF 3 Rotate the rounded head of the camera to the desired angle for surveillance 4 1 1 Camera Learning Setup If there is interference from another wireless device the Learning Switch can program the unit to avoid it Push the Learning Switch on the back of the camera from OFF to ON then press the Eliminate button on the receiver for 3 seconds The picture will become clearer on the screen Learning 4 1 2 Camera Alarm Setup 1 The camera provides a Sound Detection alarm Alarm 1 Press within 2 minutes when alarm sounds to put into snooze mode to ot next alarm event gt Qo _ Sta rr OFF VOX Sound Alarm Setup To set up the sound alarm slide the alarm switch to the VOX position The system will enter standby mode until a sound triggers the alarm When sound is detected the alarm sounds for two minutes or until the Eliminate Alarm button is pressed which will put the system into snooze mode for 35 seconds After the 35 seconds is up the alarm will go back into standby mode until triggered by the next sound alarm event Turn Off Alarm To turn off the alarm slide the alarm setting switch to the Off position The alarm function will be disabled Note The Sound alarm will be turned off automatically if the Eliminate Alarm button is not pressed within 2 minutes after the alarm sounds If both the bat
4. se undesired operation Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment CAUTIONS Do not expose the device to water or other liquids Turn off the Camera Receiver when the system is not in use Make sure the power adapter is easily accessible Only remove the Camera Receiver from the main power line by unplugging the adapter Do not cut the DC power cable of the device to fit with another power source Make sure batteries are disposed of properly EU Environmental Protection Electrical waste products discharged batteries should not be disposed of with household waste Please recycle where facilities exist Check with your Local Authority or retailer for recycling advice TRADEMARKS All brand names and products are registered trademarks of their respective Companies DISCLAIMER The information in this document is subject to change without notice The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaim any implied warranties of selling or functionality for any particular purpose LEGAL DISCLAIMER Warning Your security camera is a quality digital product You have to take utmost care while handling this product in order to ensure its reliability amp durability Digital Peripheral Solutions Inc 8015 E Crystal Drive Anaheim CA 92807 1 8
5. tery and A C adapter are in use and the alarm setup failed to trigger turn the camera and the receiver off and then back on to re activate the alarm 4 2 Setting Up the Receiver 1 Connect the receiver to the adapter and then slide the power switch to the ON position f LA Note This receiver can also use dry batteries as a power source by loading 4 AA batteries into the battery compartment at the back of the camera with their polarities in the correct position The AC adapter will work instead of batteries after it is plugged in If the camera is not going to be used for a long period of time please unplug the adapter and remove the batteries a fC m 1 es The camera can run off of batteries for up to 5 hours 2 Adjust the volume control to the desired level 3 Set the channel of the receiver to the same channel as the camera by pressing the channel button continuously the pictures will display on the screen when the channels match Note The receiver supports up to 4 cameras working at the same time If there are 2 3 or 4 cameras working you can press and hold the channel button about 3 seconds to enter auto switch browse mode and the channels will by displayed one by one for 6 seconds at a time 5 Specifications Item Value GENERAL Transmission Frequency ISM 2 400 2 483 MHz Transmission Power 10mW CE 2mW FCC Operating Frequenc
6. y 2414MHz 2432MHz 2450MHz 2468MHz Unobstructed Effective 100m 328ft Min Range Eee N Mode FHSS GFSK Operating Temperature 10 50 Degree C 14 122 Degree F Operating Humidity lt 85 RH Imaging Sensor Type CMOS Picture Total Pixels Ue EA Horizontal Resolution 380 TV Lines iew Angle 55 inimum Illumination OLux IR ON Image Resolution 320x240 10fps CAMERA Night Vision Range 5m Battery Working Time 5 hours IR OFF otion Detection Distance 5m 16ft Sound Control Sensitivity gt 65dB Consumption Current 280mA Max Power Supply DC 8V Dimensions WxDxH 86 48 135 mm 3 5 2 5 5 in Weight 146 g 5 2 oz LCD Screen Type 2 36 inches TFT LCD Effective Pixels 480x234 Receiving Sensitivity lt 85dBm Battery Working Time 5 hours MONITOR Consumption Current 200mA Max Power Supply IDC 8V Dimensions WxDxH 86 54 143 mm 3 5 2 25 5 75 in Weight 130 g 4 6 oz Actual transmission range may vary according to weather Location interference and building construction All the specifications are subject to minor change without prior notice 6 FCC information This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cau
Download Pdf Manuals
Related Search