Polaroid ION Digital Camera User Manual
Contents
1. Do not ACAUTION petighiten strainer Ring lok during operation Do not ACAUTION pepsi pump with closed suction or discharge valve WATER CHEMISTRY Proper and consistent use of chemicals is necessary to manage a water system Chlorine is the most commonly used chemical to provide clean sanitary water Daily administration of dry or liquid chlorine calcium or sodium hypochlorite is essential IMPORTANT Maintain the correct level of acidity or alkalinity of the pool water Readings above pH 7 0 are alkaline A pH 7 0 is neutral Readings below pH 7 0 are acidic A desirable range is 7 2 to 7 4 WwWw waynepumps com WIP100 WIP150 I HAIR AND LINT STRAINER Do not Maintenance 1 Switch off the power ACAUTION retighten A DANGER X 2 Close the valves in the suction and strainer Ring Lok during operation Disconnect tag and lock return line WINTERIZING out power source before 3 Turn strainer Ring Lok counter Always protect system from freezing attempting to install service clockwise and remove stainer cover temperatures Drain the system if there relocate or perform any maintenance 4 Lift strainer basket away from the is a possibility of freezing To drain the 1 Motors are self lubricating no pump system additional lubrication is required 5 Clean and reposition the basket 1 Units with a filter 2 Clean pool pump strainer of hair into the pump Take care to seat the a Sand filte2. A Description Replacement Number 1 Cap and O ring 69010 001 1 2 Filter 28477 001 1 3 Tank 1 4 Motor 1 Limited Warranty For one year from the date of purchase WAYNE Water Systems WAYNE will repair or replace at its option for the original purchaser any part or parts of its Sump Pumps or Water Pumps Product found upon examination by WAYNE to be defective in materials or workmanship Please call WAYNE 800 237 0987 for instructions or see your dealer Be pre pared to provide the model number and the serial number when exercising this warranty All transportation charges on Products or parts submitted for repair or replacement must be paid by purchaser This Limited Warranty does not cover Products which have been damaged as a result of accident abuse misuse neglect improper installation improper maintenance or failure to operate in accordance with WAYNE S written instructions THERE IS NO OTHER EXPRESS WARRANTY IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO ONE YEAR FROM THE DATE OF PURCHASE THIS IS THE EXCLUSIVE REMEDY AND ANY LIABILITY FOR ANY AND ALL INDIRECT OR CONSEQUENTIAL DAMAGES OR EXPENSES WHATSOEVER IS EXCLUDED Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusions or limitations of incidental or consequential damages so the above limitations might not apply to you This limited war
3. areas where codes specify a primer must be used REMINDER Keep your dated proof of purchase for warranty purposes Attach it to this manual or file it for safekeeping 2010 WAYNE Pumps For parts product amp service information visit WWWw waynepumps com 320403 001 4 10 Operating Instructions and Parts Manual RECOMMENDED ADHESIVES PVC PVC Joint PVC ABS Joint Uni Weld Uni Weld Pool Tite 2000 Pool Tite 2000 Suregard Weld Suregard Flex 20 All No 5 IPS Weld On 705 IPS Weld On 794 These recommendations are examples only and are not intended to restrict brands Installation Continued Consider climatic conditions when applying adhesives Atmospheric conditions with high humidity will make the adhesive action of certain glues less effective Follow the manufacturer s instructions THREADED CONNECTIONS Use only Teflon tape or equivalent on threaded plumbing connections Other pipe compounds may damage threads Do not use silicone or petroleum based compounds Do not overtighten Hand tightening plus 1 2 turn is sufficient PUMP PLUMBING Suction pipe should be as large or larger than discharge pipe Avoid using a suction pipe smaller than pump connection 1 Keep the piping as straight and short as possible and of suitable size 2 Do not connect an elbow directly into the pump inlet A length of straight pipe will allow proper entry of the water to the pum
4. circuit breaker Be sure wire size is sufficient for pump HP and distance from power source Install a ground fault circuit interrupter Disconnect tag and lock out power source before for maximum safety A DANGER X wy attempting to install service relocate or perform any maintenance 1 Switch OFF power 2 Remove cover from back of motor 3 The motor is factory wired for 230 volts 4 Move Voltage Change Switch to 115 volts 5 Reinstall cover to back of motor Connections Voltage Change Switch 115 230 Volts Figure 1 Voltage Change Switch Operation Prime pump before attempting to operate To prime pumps located above water level remove strainer cover fill strainer body with water then replace cover If pump and all piping is located below water level the pump will self prime After pump has been primed energize motor and open all suction and discharge line valves If no flow is observed in five minutes stop the motor and reprime If the pump fails to operate check for air leaks Refer to troubleshooting section After about 10 minutes of operation check the return fittings for air bubbles A continuous flow of air indicates leaks in the suction line Locate and correct any leaks immediately CONTROLLING PUMP DISCHARGE Keep the gate valve in the suction line fully open during operation To control the discharge use a valve in the return line
5. ON 65 Thi AWARNING or its power cord may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm Wash hands after handling SAFETY GUIDELINES 1 Read these rules and instructions carefully Failure to follow these instructions could cause serious bodily injury and or property damage To reduce AWARNING __ 7o7eu of injury do not permit children to use this product unless they are closely supervised at all times This ACAUTION i is for use with permanently installed pools If specified the pump may be used with hot tubs and spas Do not use with storable pools A permanently installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage A storable pool is constructed so that it may be readily disassembled for storage and reassembled to it s original integrity AWARNING Pump only clear water Do not pump flammable or explosive fluids such as gasoline fuel oil kerosene etc Do not use in a flammable and or explosive atmosphere Personal injury andlor property damage could result AWARNING All wiring must be performed by a qualified electrician The pump must be installed in compliance with all local codes and the National Electrical Code a 2 Do not install within an outer enclosure or benea
6. Operating Instructions and Parts Manual WIP100 WIP150 Please read and save these instructions Read carefully before attempting to assemble install operate or maintain the product described Protect yourself and others by observing all safety information Failure to comply with instructions could result in personal injury and or property damage Retain instructions for future reference WAYNE Pool Pumps Description This swimming pool pump is designed for use with permanently installed pools only These pools can be either in ground or above ground Unpacking After unpacking the unit carefully inspect for any damage that may have occurred during transit Check for loose missing or damaged parts General Safety Information This manual contains information that is very important to know and understand This information is provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS To help recognize this information observe the following Danger A DANGER indicates an imminently hazardous situation which if not avoided WILL result in death or serious injury Warning AWARN l NG indicates a potentially hazardous situation which if not avoided COULD result in death or serious injury Caution ACAUTION Paiste a potentially minor or moderate injury Notice NOTICE indicates important information that if not followed may cause damage to equipment CALIFORNIA PROPOSITI
7. each full speed 2 Motor windings connected for wrong at shaft voltage on dual voltage model Motor overheats 1 Low voltage High pump pressure 1 Discharge valve or inlet fittings closed protector trips 2 Motor windings connected for wrong too much voltage on dual voltage model 2 Return lines too small 3 Inadequate ventilation 3 Dirty filter Pump does not 1 Pump is not primed Low pump pressure 1 Pump running at reduced speed see deliver water 2 Closed valve in suction or discharge previous line 2 Wrong rotation 3 Leakage or air into suction system 3 Discharge valve or inlet fittings open 4 Impeller clogged too wide Noisy pump and 1 Plugged basket in skimmer or hair in Air bubbles at inlet 1 Leakage of air into suction line at motor lint strainer fittings connections or valve stem 2 Worn motor bearings 2 Cover gasket around hair and lint 3 Valve in suction line partly closed strainer needs cleaning 4 Suction line partly plugged 3 Restriction in suction line 5 Vacuum hose plugged or too small 4 Low water level in pool 6 Pump not supported properly Www waynepumps com Operating Instructions and Parts Manual WIP100 WIP150 For Replacement Parts or technical assistance call 1 800 237 0987 Please provide following information Model number Serial number if any Part description and number as shown in parts list Address parts correspondence to WAYNE Pumps 101 Production Drive Harrison OH 45030 U S
8. p 3 Slope horizontal runs upward to the pump to prevent trapping air 4 Use independent piping supports to alleviate strain on the pump 5 Keep as much of the suction line as possible below the water level to reduce priming time 6 Install valves and unions in the pump suction and return lines to facilitate servicing Valves will throttle the pump discharge Valves are also essential for pump maintenance if the system is installed below deck level 7 Use a check valve in the suction pipe for inground pumps at or below the water level if the suction lift is more than 5 feet or the dry suction is more than 10 feet long Keep the valve in the suction line fully open during operation WIRING AWARNING 3 All wiring must be performed gt by a qualified electrician The pump must be installed in compliance with all local codes and the National Electrical Code When motor installation is within 5 ft 1 5 m of the pool s interior walls a solid copper bonding conductor minimum size No 8 AWG 8 4 mm should be connected from the accessible wire connector on the motor e to all metal parts of the swimming pool e to all electrical equipment e to metal conduit e to metal piping within 5 ft 1 5 m of the pool s interior walls IMPORTANT Use copper conductors only Refer to information on motor nameplate for electrical service data Install motors with a fused disconnect switch or dedicated
9. r Backwash for 3 to 5 and lint basket properly minutes and then set dial valve to 3 Visually inspect motor for blockage 6 Clean the o ring and relubricate winterize position of air vents on motor shell Remove with petroleum jelly if necessary b Cartridge filter Clean the filter any debris after shutting off breaker 7 Clean o ring seats on the cover and element and store in dry area 4 Replace worn shaft seals strainer 2 Drain system by loosening drain 8 Refit the cover and strainer Ring plug The drain plug does not Lok hand tighten only have to be completely removed Removing pipe caps will facilitate 9 Open the valves to return pump to draining also operation Troubleshooting Chart Symptom Possible Cause s Symptom LERENO Motor does not 1 Disconnect switch or circuit breaker in Low pump capacity 1 Valve in suction or discharge line start OFF position partly closed 2 Fuses blown or thermal overload open 2 Suction or discharge line partly plugged 3 Locked motor shaft 3 Suction or discharge line too small 4 Motor windings burned out 4 Pump running at reduced speed see 5 Defective starting switch inside previous single phase motor 5 Plugged basket in skimmer or hair 6 Disconnected or defective wiring and lint strainer 7 Low voltage 6 Dirty filter 7 Impeller clogged 8 Wrong rotation 3 phase only Motor does not 1 Low voltage Leakage of water Shaft seal requires replacement r
10. ranty gives you specific legal rights and you may also have other legal rights which vary from state to state In no event whether as a result of breach of contract warranty tort including negligence or otherwise shall WAYNE or its suppliers be liable for any special consequential incidental or penal damages including but not limited to loss of profit or revenues loss of use of the products or any associated equipment damage to associated equipment cost of capital cost of substitute products facilities services or replacement power downtime costs or claims of buyer s customers for such damages You MUST retain your purchase receipt along with this form In the event you need to exercise a warranty claim you MUST send a copy of the purchase receipt along with the material or correspondence Please call WAYNE 800 237 0987 for return authorization and instructions DO NOT MAIL THIS FORM TO WAYNE Use this form only to maintain your records MODEL NO SERIAL NO INSTALLATION DATE ATTACH YOUR RECEIPT HERE WWww waynepumps com
11. th the skirt of the hot tub or spa unless so marked READ amp FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS DO NOT DISCARD Installation LOCATION CETATE y Disconnect tag and lock out power source before attempting to install service relocate or perform any maintenance Locate pump as close to pool spa as possible Install the pump on a hard level surface that is dry well ventilated and away from direct sunlight The surrounding area should provide protection from the elements and ample room for maintenance and service Ensure the drainage will flow away from the pump Above ground pool pumps are not self priming If suction line valves are installed the pump may be located above water level Keep the vertical distance from the water level to a minimum Otherwise the pump must be located below filled water level to facilitate priming Inground pool pumps are self priming Mount pump below water level for easy priming If the pump must be located above the filled water level keep the vertical distance to a minimum GENERAL PLUMBING SOLVENT WELD CONNECTIONS Use rigid or flexible PVC pipe Ensure pipe ends are clean and free of any flash caused by the cutting operation Use the proper adhesive for the type of pipe specified See list of recommended adhesives on page 2 NOTE Use an adhesive primer to ensure adhesive joints are secure Suregard P 3000 has a purple tracer to qualify in
Download Pdf Manuals
Related Search