Polaris 800 X2 Offroad Vehicle User Manual
Contents
1. S Portsmith User Guide Portsmith Ethernet Cradle Model Numbers PS6PMSE PS6SPMSE 6 amp PS6HVE Copyright 2002 Portsmith Inc All rights reserved The information in this document is subject to change without notice Disclaimer Portsmith Inc assumes no responsibility for any damage or loss resulting from the use of this user guide Portsmith Inc assumes no responsibility for any loss or claims by third parties that may arise through the use of this product Portsmith Inc assumes no responsibility for any damage or loss caused by deletion of data as a result of malfunction dead battery or repairs Be sure to make backup copies of all important data on other media to protect against data loss First Edition June 2001 Rev 1 Version 1 5 PalmOS and HotSync are registered trademarks and Palm is a trademark of Palm Inc or its subsidiaries Third party products and brand names may be trademarks or registered trademarks of their respective owners Handspring Visor Visor Deluxe and Visor Platinum are registered trademarks of Handspring Inc Microsoft Windows Window ME and Windows NT are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries IBM is a registered trademark of IBM in the United States Intellisync is a trademark of Pumatech Inc that may be registered in some jurisdictions XTNDConnect is a registered trademark of Extended Systems DataViz2. DISBURSEMENTS ATS Regulatory Information FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio or television technician for help Portsmith Inc is not responsible for radio TV interference caused by using unauthorized cables or by making unauthorized changes to this equipment European Union Notice Products with CE marking comply with both the EMC Directive 89 336 EEC and the Low Voltage Directive 73 23 EEC issued by the Commission of the Eu
3. e MultiMail e AvantGo Client Chapter 3 Troubleshooting Use the table below to identify and correct problems you might encounter when setting up or using your Portsmith Ethernet Cradle Troubleshooting Matrix The amber LED remains dark Make sure the power supply is securely when the Ethernet cradle is plugged in The amber LED blinks continuously The amber LED is fully lit but no synchronization took place and the green LED did not blink The green LED remains dark connected and receiving power Make sure a DHCP server is configured and operational on the network to which the Ethernet cradle is connected Remove the PDA from the Ethernet cradle and reinsert it making sure it is gently but firmly seated in the Ethernet cradle Press the synchronization button Confirm that the Ethernet cable is a straight through or feed through cable Confirm that the Ethernet cable is properly connected to the cradle and to a functioning 10 or 10 100 Mbps auto sensing network device 10 Technical Support For additional information refer to the FAQ List in the Support Section at www portsmith com If you need additional assistance you can contact technical support via e mail at support portsmith com or directly by phone at 208 395 1300 Please provide the following information e Your name email address and e Portsmith Ethernet Cradle model phone number number e Portsmith Ethernet Cradle se
4. s Through our Ethernet Cradle users can download or synchronize with corporate network data server resident data or access a live Internet connection This user guide provides an overview of setting up and using the Portsmith Ethernet Cradle In addition to accessing data and the Internet the Portsmith Ethernet Cradle also provides recharging capabilities on applicable handheld models Minimum Requirements The following minimum requirements must be met for your network PDA and desktop computer Optional Dynamic host configuration protocol DHCP server configured and operational on the network 10 Mbps or 10 100 Mbps auto sensing network connection 10BaseT Ethernet cable PDA running the Palm Operating System Palm M500 or M505 if you have the PS6PM5E Cradle Handspring Visor Visor Deluxe Visor Platinum if you have the PS6HVE Cradle The AC power adaptor for Portsmith Ethernet Cradle Portsmith Ethernet Cradle A desktop computer with HotSync Manager installed and configured to use a local serial or USB synchronization cradle This computer must also have a web browser and Internet access HotSync Desktop installed on the user s networked desktop computer This is one method for the PDA to synchronize with the desktop computer over the network Other third party desktop synchronization software which supports network synchronization such as PumaTech Intellisync installed on both the PDA and the desktop computer These app
5. all the software on the desktop computer and the PDA 2 Make sure the synchronization software is set up for use on a network Make sure the appropriate user name is selected in the synchronization software 4 Place the PDA in the cradle attached to the local PC and press the synchronization button This operation records network information about the desktop computer on the PDA With this information the PDA can locate the computer when a synchronization operation is performed over the network U NOTE To perform any synchronization with the desktop computer using the Portsmith Ethernet Cradle the desktop computer must be on the desktop synchronization software must be running and the software must be set up for network use Installing Server based Network Synchronization Software To configure server synchronization follow the manufacturer s installation instructions to install the software on the server and the PDA s The Portsmith Ethernet Cradle is designed to support any software that uses standard TCP IP on the Palm Operating System The Cradle s function has been verified with the applications listed below For instructions on using and troubleshooting the software on your PDA or computer see the software manufacturer s installation documentation Server based Synchronization Software e HotSyncServer e XTNDConnect Server Network Synchronization Software e HotSync Manager e Intellisyne Network Software e PalmScape
6. application tries to communicate over TCP IP This behavior preserves battery life It is the default configuration of the driver Disabled The driver is disabled It will perform no activity while in this mode Automatic HotSync This mode is the same as the Enabled mode except the driver simulates the press of the cradle s HotSync button when the driver detects the PDA s presence in the Portsmith Ethernet cradle Automatic Connect This mode is the same as the Enabled mode except the driver opens the TCP IP connection upon cradle presence detection rather than waiting for an application to attempt to communicate over TCP IP Some applications require this behavior Note This mode can drain the batteries of Alkaline battery powered PDAs Configuration Panel This mode is the same as the Enabled mode except the driver will display its configuration form when the cradle is detected PDA Functionality Buttons Connect Establish a connection e Disconnect Disconnect the current connection HotSync Perform a HotSync If the connection isn t currently established it will establish a connection first Using the Portsmith Ethernet Cradle to HotSync Once the PDA has been docked with a Portsmith Ethernet Cradle there are three different ways that you can HotSync over the network 1 Pressing the button on the Portsmith Ethernet Cradle itself or i O 2 Tapping the HotSync Icon from the Palm Application Launch
7. atus and Configuration Screen The driver s status and configuration form may be viewed by selecting the PSCradle icon in the Palm Application Launcher Ol The following form will be displayed The items on this screen are described below Cradle Status Jani ERT This item shows if the Driver has detected the PDA s presence in a Portsmith Ethernet Cradle R e Docked The PDA is currently in a Portsmith Ethernet Portsmith Cradle l Undocked The PDA is not currently in a Portsmith i heti status Dorked onnect Status Inactive Ethernet Cradle Firmware Yer 0107180 Driver Ver 1 0 01 Connection Status Driver Mode w Enabled This item shows the status of the connection to the Portsmith Ethernet Cradle Active There is currently a connection established e Inactive The connection is not currently established Disconnecting The connection is being terminated A Firmware Ver If the PDA is in a Portsmith Ethernet Cradle this will show the current firmware version installed on the Portsmith Ethernet Cradle Driver Ver The current version of the Portsmith Cradle Driver on the PDA Driver Mode This item allows the user to configure the current mode of the Portsmith Cradle Driver Enabled The driver is enabled and will configure the TCP IP communication session when it detects the PDA s presence in a Portsmith Ethernet Cradle In this mode the driver does not actually open the TCP IP session until an
8. conditions of this License If you do not agree with these terms and conditions you should return the software and your money will be refunded License Agreement This license permits you to 1 Use this software in the conduct of business without limit when the software is used with the Portsmith Ethernet Cradle 2 Copy the software onto any PDA connected to a Portsmith Ethernet Cradle You are not permitted to 1 Make modifications to any portion of this software product 2 Merge this software product or any portion of it into another program or product 3 Decompile reverse engineer disassemble or otherwise reduce the software to a human perceivable form Warranties All warranties are governed by the Software Limited Warranty included in this document NOTE BY INSTALLING THE SOFTWARE YOU A CKNOWLEDGE THAT YOU HAVE READ THIS A GREEMENT UNDERSTAND ITAND AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS YOU FUR THER A GREE THAT IT IS THE COMPLETE AND EXCLUSIVE STATEMENT OF THE A GREEMENT BETWEEN US AND SUPERSEDES ANY PROPOSAL OR PRIOR A GREEMENT EITHER ORAL OR WRITTEN AND ANY OTHER COMMUNICATIONS BETWEEN US RELA TING TO THE SUBJECT MATTER OF THIS A GREEMENT YOU FURTHER A GREE THA TIF PORTSMITH INC IS REQUIRED TO ENGA GE INANYPROCEEDING LEGAL OR OTHERWISE TO ENFORCE ITS RIGHTS UNDER THIS A GREEMENT PORTSMITH INC SHALL BE ENTITLED TO RECOVER FROM LICENSEE IN ADDITION TO ANY OTHER SUMS DUE REASONABLE ATTORNEY FEES COSTS AND
9. er on the PDA or 3 Tapping the HotSync Button in the Portsmith Cradle Driver Using the Portsmith Ethernet Cradle for a Network Connection Once the PDA has been docked with a Portsmith Ethernet Cradle there are three different ways that you can utilize the network connection After the connection has been established you may use any application that requires a network connection ro nsona cation Tauncner A 1 Go into PSCradle from the Palm Application Launcher and tap the Connect button or 2 Go to the Network section of the Preference Panel gt from the Palm O Application Launcher and tap the Connect button or 3 Go into the application you wish to use most applications attempt to connect using the current settings The current settings have been set to work with the Portsmith Ethernet Cradle when it was inserted Install amp Configure Network Synchronization Software Before the Portsmith Ethernet Cradle can be used to perform a Network Synchronization third party synchronization software must be installed on both the desktop computer and the PDA that will be synchronizing with it The software locates the desktop computer on the network being accessed via the Portsmith Ethernet Cradle NOTE You might need the assistance of your network system administrator to install the software on your desktop To configure network synchronization 1 Follow the software manufacturer s installation instructions to inst
10. for a full refund of the purchase price If the purchaser wishes to upgrade or convert to another Portsmith Inc product within the thirty 30 day period purchaser has the right to return the product and apply the full purchase price toward the purchase of the other product Any other return will be subject to Portsmith Inc s existing restocking policy PORTSMITH INC WARRANTS THAT THIS PRODUCT IS NEW OR HAS BEEN REMANUFACTURED TO MEET NEW STANDARDS USING NEW OR SERVICEABLE USED PARTS PORTSMITH INC MAKES NO OTHER WARRANTY EITHER EXPRESSED OR IMPLIED WITH RESPECT TO THIS PRODUCT PORTSMITH INC SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Some states or provinces do not allow limitations on how long an implied warranty lasts so the above limitation or exclusion may not apply to you THE REMEDIES PROVIDED HEREIN ARE CUSTOMER S SOLE AND EXCLUSIVE REMEDIES IN NO EVENT SHALL PORTSMITH INC BE LIABLE FOR ANY LOST PROFITS DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES WHETHER BASED ON CONTRACT TORT OR ANY OTHER LEGAL THEORY 13 Software Warranty This warranty applies only to software products The warranty for hardware products is described elsewhere Portsmith Inc does not warrant that the operation of the program will meet your requirements or be error free The program is provided AS IS without warranty of any kind The entire risk as t
11. g the Portsmith Cradle Driver The Portsmith Cradle Driver is named PSCradle pre This driver may be downloaded from the Portsmith web site on the Internet with the following steps 1 2 P On a PC configured for HotSync Manager local synchronization through a serial or USB synchronization cradle open the web browser In the address bar of the web browser enter the following address http www portsmith com psdwnld When the web page appears select the appropriate model of cradle and PDA Select the link to download the Portsmith Cradle Driver PSCradle prc Your web browser should prompt you to either open or save the file Select the open option If HotSync Manager is configured for more than one PDA the HotSync Install Tool will prompt you to select where to install the file Select the identity associated with the PDA where you want to install the driver Install Tool 4 0 er x m Select a user and click OK Username m5000 Cancel If you wish to enable the PDA to synchronize over the network with this desktop machine you must enable network mode in HotSync Manager On a Windows computer this can be done by right clicking on the HotSync icon in the Windows system tray If the Network option is not checked Select it by clicking on Network in the menu Perform a local synchronization between the desktop computer and the PDA where you want to install the driver This is done by placing
12. is a trademark of DataViz Inc MultiMail is a registered trademark of Actual Software Corporation AvantGo is a trademark of AvantGo Incorporated All other registered trademarks trademarks service marks and or logos are the property of their respective companies Portsmith Inc 960 Broadway Suite 300 Boise ID 83706 USA Wwww portsmith com Contents Introduction About the Portsmith Ethernet Cradle Chapter 1 Chapter 2 Chapter 3 Appendix A Appendix B Minimum Requirements Optional Preparing to Use the Portsmith Ethernet Cradle Connect the Ethernet Cradle to a Network LED Indicators Using the Portsmith Ethernet Cradle Installing amp Using the Portsmith Cradle Driver Operation of the Portsmith Cradle Driver Status and Configuration Screen Using the Portsmith Ethernet Cradle to HotSync Using the Portsmith Ethernet Cradle for Network Connection Install and Configure Network Synchronization Software Install Server based Synchronization Software Optional Supported Software Troubleshooting Troubleshooting Matrix Technical Support Glossary of Terms Warranties and Other Product Information Hardware Warranty Software Warranty Software License Agreement Regulatory Information FCC Statement Nn O O O WANNA DAD 10 10 11 12 13 13 14 15 16 16 Introduction About the Portsmith Ethernet Cradle The Portsmith Ethernet Cradle is a network connectivity accessory for Palm OS PDA
13. lications provide alternate methods to synchronize the PDA with the desktop computer over the network Server based synchronization software such as XTNDConnect Server or HotSyncServer installed on both the network and the PDA Internet applications such as PalmScape MultiMail or AvantGo can be installed on the PDA and used to communicate through the Portsmith Ethernet Cradle to an Internet connected network Chapter 1 Preparing to Use the Portsmith Ethernet Cradle Installation Overview Before using the Portsmith Ethernet Cradle you and your network system administrator must properly configure your hardware and software Below is a summary of the steps required for proper configuration This chapter provides details about each step listed below e Connect the Ethernet cradle to the network e Install and configure the Portsmith Cradle Driver on your PDA e Install and configure network synchronization software or Internet communication software Connect the Ethernet Cradle to the Network To use the Ethernet cradle it must be connected to a 10Base T or 10 100Base T Ethernet network that is setup for TCP IP communication and DHCP configuration To connect the Ethernet cradle to the network 1 Connect one end of a 10Base T Ethernet cable to the RJ45 connector on the back of the Ethernet cradle 2 Connect the other end of the Ethernet cable to an active 10 100Base T Ethernet network connection 3 Connect the round plug of
14. o the quality and performance of the program is with the purchaser If the program proves defective or inadequate purchaser assumes the entire cost of servicing or repair Portsmith Inc makes no other warranty either expressed or implied with respect to this product Portsmith Inc specifically disclaims the implied warranties of merchantability and fitness for a particular purpose Some states or provinces do not allow limitations on how long an implied warranty lasts so the above limitation or exclusion may not apply to you However any implied warranty of merchantability or fitness is limited to the ninety 90 day duration of this written warranty Purchaser s exclusive remedy shall be the replacement of defective media which is returned to Portsmith Inc If Portsmith Inc is unable to replace the media within a reasonable amount of time the purchaser may terminate this agreement by returning the program and all copies documentation and proof of purchase for a refund of the purchase price THE REMEDIES PROVIDED HEREIN ARE CUSTOMER S SOLE AND EXCLUSIVE REMEDIES IN NO EVENT SHALL PORTSMITH INC BE LIABLE FOR ANY LOST PROFITS DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES WHETHER BASED ON CONTRACT TORT OR ANY OTHER LEGAL THEORY 14 Software License Agreement IMPORTANT Before installing the software please carefully read this License Agreement Installation indicates your acceptance of the terms and
15. rial e PC make model and operating number system e PDA make and model e Server software e Synchronization software e Detailed problem description name and version NOTE You can find the Portsmith Ethernet Cradle serial number on the label on the bottom of the Cradle 11 Appendix A Glossary of Terms Desktop Computer A PC or Laptop where information resides that you perform a HotSync with using a USB or serial cradle DHCP Server An acronym for Dynamic Host Configuration Protocol A server that assigns an IP Address to the Portsmith Ethernet Cradle so it can access the Internet and the network DNS Server Domain Naming System converts host names URL s into internet addresses Gateway IP Address IP address for the server that transfers data between networks IP Address Internet Protocol Address used to identify your Portsmith Ethernet Cradle from other devices on the network Local Synchronization A synchronization using a USB or Serial Cradle directly connected to a Desktop Computer Network Synchronization Synchronization with a Desktop Computer on the network PDA Personal Digital Assistant specifically Palm s m500 505 or Handspring s Visor Deluxe Platinum Portsmith Cradle Driver A utility to aid in configuring a PDA for use with the Portsmith Ethernet Cradle PSCradle pre The filename of the Portsmith Cradle Driver Server based Synchronization Synchronization with a server that is attached to
16. ropean Community Compliance with these directives implies conformity to the following European Norms in brackets are the equivalent international standards e EN55022 CISPR 22 Electromagnetic Interference e EN50082 1 IEC801 2 IEC801 3 IEC801 4 Electromagnetic Immunity e EN 60950 IEC60950 Product Safety 16 VCCI Notice This is a Class B product to be used in a domestic environment based on the Technical Requirement of the Voluntary Control Council for Interference from Information Technology Equipment VCCI If this is used near a radio or television receiver in a domestic environment it may cause radio interference Please install and use the equipment according to the instruction manual CORG 1 HHRLBRESERRESAEMHBRS VCCI OR CBSO TFAZABRRHRECT CORRE REM CERT 5 CBR MEESSROFCEPHVET TOBAGA AU AiR ET SBLIBKENSCEPHVET CAUTION Changes or modifications not covered in this user guide must be approved in writing by the manufacturer Regulatory Engineering Department Changes or modifications made without written approval may void the user authority to operate this equipment Portsmith Inc 960 Broadway Suite 300 Boise ID 83706 USA Telephone 888 293 1302 Toll Free in the U S or 208 395 1300 from outside the U S Fax 888 501 8086 Toll Free in the U S or 561 619 5810 from outside the U S 17
17. the AC adaptor cable into the AC adaptor connector jack on the back of the Ethernet Cradle then plug the AC adaptor into a standard electrical outlet NOTE DHCP services must be available to assign the Ethernet cradle an IP address a gateway IP address a subnet mask and a DNS server Once connected to a network and a power supply the Ethernet cradle continuously attempts to establish a link with the local DHCP server to collect network parameters and obtain an IP address You can monitor this querying process which continues until proper configuration is achieved by observing the operational indicator LEDs on the RJ45 Ethernet connector on the back of the Ethernet cradle See the table on the following page for a description of LED indicators LED Indicators LED color and behavior Amber at half brightness Amber blinking Querying the DHCP server to collect network parameters Amber at full brightness Network configuration data received Green at half brightness Network link established Green blinking Data being transmitted Chapter 2 Installing and Using the Portsmith Cradle Driver on Your PDA The Portsmith Cradle Driver must be installed and configured on the PDA before the PDA can communicate through the Ethernet cradle The Portsmith Cradle Driver automatically detects if the PDA is in the Portsmith Ethernet Cradle and automatically configures the PDA for TCP IP communication over the attached Ethernet network Installin
18. the PDA in the local HotSync cradle and pressing the HotSync button When the synchronization completes the driver will be installed on the PDA Tip You can also install the Portsmith Cradle Driver on a PDA by beaming it from another PDA on which it has already been installed v Local USB v Local Serial Modem v Network Setup Custom File Link View Log About Help Exit Operation of the Portsmith Cradle Driver The Portsmith Cradle Driver is designed to provide seamless TCP IP connectivity without user intervention The driver automatically provides the following functions Detection of the PDA s presence in a Portsmith Ethernet Cradle Configuration of the PDA to provide TCP IP communication over the attached Ethernet network This includes IP address subnet mask default gateway and DNS server e Session termination upon removal from the cradle Connection and docking status information and visual feedback f A p Setting up e Optional synchronization upon insertion into the cradle Pisara NERS Optional network connection establishment upon insertion into the cradle Preservation of modem communication settings if set Upon insertion into the Ethernet cradle the Driver will briefly display the splash screen shown below while it is configuring the communication session This is visual confirmation that the PDA is docking with the cradle The St
19. the network Subnet Mask Used by networked devices to determine whether any given IP address is on the local network or outside the local network TCP IP Transfer Control Protocol Internet Protocol a standardized method of data communication over the Internet 12 Appendix B Warranties and Other Product Information Hardware Warranty Portsmith Inc warrants this product against defects in materials and workmanship to the purchaser for a period of two 2 years from the date of shipment This warranty is limited to a repair or replacement of the product To obtain warranty service the purchaser must first call Portsmith Inc for an RMA number then return the product to Portsmith Inc for repair or replacement Purchaser shall prepay shipping charges for products returned to Portsmith Inc Portsmith Inc will pay for return of the products to purchaser except that purchaser shall pay all shipping charges duties and taxes for products returned to Portsmith Inc from a country other than the United States Portsmith Inc makes no other warranty of any kind with regard to this material Portsmith Inc shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this material Within thirty 30 days of receipt should the product fail for any reason other than damage due to customer negligence purchaser has the right to return the product
Download Pdf Manuals
Related Search