Planet Technology SW-504 Switch User Manual
Contents
1. Figure 2 2 SW 504 rear panel Figure 2 3 amp 2 4 show the front panel and rear panel of SW 804 Figure 2 3 SW 804 front panel 9 1 LOLOCXCOCALLACO Figure 2 4 SW 804 rear panel 2 1 3 LED Indicators LED Color Function Lights to indicate that the Switch is powered on PWR Green Lit indicate the link through that port is successfully established Blink indicate that the Switch is actively sending or receiving data over that port LNK ACT Green Power Notice 1 The device is a power required device it means it will not work till it is powered If your networks should active all the time please consider using UPS Uninterrupted Power Supply for your device It will prevent you from network data loss or network downtime 2 In some area installing a surge suppression device may also help to protect your Switch from being damaged by unregulated surge or current to the Switch or the power adapter 2 2 Installing the Switch This part describes how to install your Desktop Fast Ethernet Switch and make connections to it Please read the following topics and perform the procedures in the order being presented This Switch does not need software configuration 2 2 1 Desktop Instal2. 3412 The Ethernet Switch scans the destination address from the packet header searches the routing table provided for the incoming port and forwards the packet only if required The fast forwarding makes the switch attractive for connecting servers directly to the network thereby increasing throughput and availability However the switch is most commonly used to segment existing hubs which nearly always improves overall performance An Ethernet Switching can be easily configured in any Ethernet network environment to significantly boost bandwidth using conventional cabling and adapters Due to the learning function of the Ethernet switching the source address and corresponding port number of each incoming and outgoing packet are stored in a routing table This information is subsequently used to filter packets whose destination address is on the same segment as the source address This confines the network traffic to its respective domain reducing the overall load on the network The Switch performs Store and Forward therefore no error packets occur More reliably it reduces the re transmission rate No packet loss will occur 3 5 Auto Negotiation The STP ports on the Switch have built in Auto negotiation This technology automatically sets the best possible bandwidth when a connection is established with another network device usually at Power On or Reset This is done by detect the modes and speeds at the second
3. Brown Figure A 1 Straight Through and Crossover Cable Please make sure your connected cables are with same pin assignment and color as above picture before deploying the cables into your network
4. 10 100Mbps Desktop Fast Ethernet Switch SW 504 SW 804 User s Manual Trademarks Copyright PLANET Technology Corp 2007 Content subjects to revision without prior notice PLANET is a registered trademark of PLANET Technology Corp All other trademarks belong to their respective owners Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representation either implied or expressed with respect to the quality performance merchantability or fitness for a particular purpose PLANET has made every effort to ensure that this User s Manual is accurate PLANET disclaims liability for any inaccuracies or omissions that may have occurred Information in this User s Manual is subject to change without notice and does not represent a commitment on the part of PLANET PLANET assumes no responsibility for any inaccuracies that may be contained in this User s Manual PLANET makes no commitment to update or keep current the information in this User s Manual and reserves the right to make improvements to this User s Manual and or to the products described in this User s Manual at any time without notice If you find information in this manual that is incorrect misleading or incomplete we would appreciate your comments and suggestions FCC Warning This equipment has been tested and found to comply with the limits for a Class B digita
5. ca aaa 5 1 2 How to Use This Manual naaa rre rrt ueni rap eene 5 1 3 Product FeaLures eterne ere ras eps ona na raa va Ia eR a s Vs 6 1 4 Product Specifications enne eren enimvero aneian 7 VER cipue 8 2 T Product DescripHOn ooi eaiede cesses nera a ORE bates veda aaia 8 2 1 1 Product OVERVIEW wie coenae ren te doe arcu eh antec Vete d via 8 2 1 2 Switch Front Panell 5 5 e e unas ea neg ra aao spe nah a naa naa 9 2 1 3 LED lridiCatO s siet rare hen rhe o ERoA eR n aea se 10 2 2 Installing the Switch ccrte oerte nnde ka sean 10 2 24 Desktop Installation s ansann 11 3 SWITCH OPERATION icssceacsieccecanssaectacsnsctecsscetecveceadetecsiaenceaedenaes 12 Bid AGGEESS TAD em 12 3 2 MECAKMING iramane saan eE EEE AEREE 12 3 3 Forwarding amp Filtering 5 6 rentrer rrr rh 12 3 4 Store and Forward 4 rera ea riae rao a n epa ln aaa v 12 3 5 Auto NegotlatlOn cts cdecanaecacavancernventiansscavagancurenedstaoierane 13 45 TROUBLESHOOTING aia a ea pex vex Ore oae qu ande iga 14 Dio c 15 A 1 Switch s RJ 45 Pin Assignments ciconiidae pna 15 A 2 RJ 45 Plug Jack PiN UE iicet deeem rne eek t 15 1 INTRODUCTION 1 1 Package Contents Check the contents of your package for following parts e Desktop Fast Ethernet Switch x 1 e User s manual x 1 e Power adapter x 1 If any of these are missing or damaged please contact your dealer immediate
6. l device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the Instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at its own expense CE Mark Warning This is a Class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures WEEE Warning To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment end users of electrical and electronic equipment should understand the meaning of the crossed out wheeled bin symbol Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately Revision PLANET 5 8 Port Desktop Fast Ethernet Switch User s Manual FOR MODELS SW 504 SW 804 Rev 1 0 November 2007 Part No 2011 A33200 000 Table of Contents 1 INTRODUCTION jis ccccscsscseanced niensrdereeseaeeaesecd vance scuaaindsineancneieodens 5 1 1 Package Contents 2 eospexer eene peas E xa xoay rau
7. lation To install the Switch on desktop simply follow the next steps Stepi Attach the rubber feet to the recessed areas on the bottom of the Switch Step2 Place the Switch on desktop near a DC power source Step3 Keep enough ventilation space between the Switch and the surrounding objects When choosing a location please keep in mind the environmental restrictions discussed in Chapter 1 Section 1 4 Product Specification Step4 Connect your Switch to network devices A Connect one end of a standard network cable to the 10 100 RJ 45 ports on the Back of the Switch B Connect the other end of the cable to the network devices such as printer servers workstations or routers etc Connection to the Switch requires UTP Category 5 network cabling with RJ 45 tips For more information please see the Cabling Specification in Appendix A Step5 Supply power to the Switch A Connect one end of the power cable to the Switch B Connect the power plug of the power cable to a standard wall outlet When the Switch receives power the Power LED should remain solid Green 11 41 3 SWITCH OPERATION 3 1 Address Table The Switch is implemented with an address table This address table composed of many entries Each entry is used to store the address information of some node in network including MAC address port no etc This information comes from the learning process of Ethernet Swi
8. ly if possible retain the carton including the original packing material and use them against to repack the product in case there is a need to return it to us for repair 1 2 How to Use This Manual This Desktop Fast Ethernet Switch User Manual is structured as follows Chapter 2 Installation The chapter explains the feature functionality and the physical installation of the Switch Chapter 3 Switch operation The chapter explains the Switch transmit operation Chapter 4 Troubleshooting The chapter explains the troubleshooting of the Switch Appendix A This chapter contains cable information of the Switch In the following section the term Desktop Fast Ethernet Switch means the two Switch devices ie SW 504 and SW 804 term of switch can be any third switches 5 F 1 3 Product Features e Comply with IEEE 802 3 10Base T IEEE 802 3u 100Base TX e 5 8 Port 10 100Mbps Auto Negotiation ports 10 20Mbps Half duplex 100 200Mbps Full duplex Auto sensing e Compact size design for wall mount or desktop placement e High performance Store and Forward Switching Architecture e Runt and CRC filtering e Flow control Back Pressure supports in half duplex mode e 1K MAC Address Table automatically learning and aging e LED indicators array for easy diagnostic troubleshooting e Plug and Play Installation e Auto MDI MDIX on each port e FCC Part 15 Class B CE 1 4 Product Specifications Hardware S
9. of both device is connected and capable of both 10Base T and 100Base TX devices can connect with the port in either Half or Full Duplex mode If attached device is 100Base TX port will set to e 10Mbps no auto negotiation 10Mbps e 10Mbps with auto negotiation 10 20Mbps 10Base T Full Duplex e 100Mbps no auto negotiation 100Mbps 100 200Mbps 100Base TX Full Duplex e 100Mbps with auto negotiation 13 1 4 TROUBLESHOOTING This chapter contains information to help you solve issues If Desktop Fast Ethernet Switch is not functioning properly make sure the Desktop Fast Ethernet Switch was set up according to instructions in this manual Some stations cannot talk to other stations located on the other port Solution The address table may contain older information than of the address table of that node Please power down to refresh the address information Performance is bad Solution Check the speed duplex mode of the partner device If the partner is set to half duplex then the performance will be poor Why the Switch doesn t connect to the network Solution Check the LNK ACT LED on the Switch Try another port on the Switch Make sure the cable is installed properly Make sure the cable is the right type Turn off the power After a while turn on power again Appendix A A 1 Switch s RJ 45 Pin Assignments When connecting your Desktop Fast Ethernet Switch to another s
10. pecification Network Ports 5 10 100Base TX RJ 45 MDI MDI X ports 8 10 100Base TX RJ 45 MDI MDI X ports Requirement Switch Architecture Dimensions W x D x H 184 x 110 x 30mm Weight KG 0 17 KG Power External Power adapter DC 9V 700 mA Store and Forward Address Table 1K entries auto learning ageing Switch 74M 1 19M Throughput g PpS 9Mpps Switch Fabric 1Gbps 1 6Gbps Shared Buffer 384K 768K Flow Control IEEE 802 3x full duplex operating and flow control Packet Control Runt amp CRC filtering Broadcast storm control Network IEEE 802 3 Ethernet IEEE 802 3u Fast Ethernet Standards and IEEE 802 3x flow control Operation o 2 6 m 20 t Temperature 0 50 C operating 20 70 C storage Humidity 5 to 90 Non condensing Regulation FCC Part Class B CE Compliance 2 INSTALLATION This section describes the functionalities of the Desktop Fast Ethernet Switch s components and guides how to install it on the desktop Basic knowledge of networking is assumed Please read this chapter completely before continuing 2 1 Product Description With concepts of Easy to Install and use Compact sized design and Simple troubleshooting PLANET SW 504 SW 804 provides cost conscious business and home users with the foundation of an integrated system of small office home office networking The SW 504 SW 804 is the fanc
11. tch 3 2 Learning When one packet comes in from any port the Switch will record the source address port no And the other related information in address table This information will be used to decide either forwarding or filtering for future packets 3 3 Forwarding amp Filtering When one packet comes from some port of the Ethernet Switching it will also check the destination address besides the source address learning The Ethernet Switching will lookup the address table for the destination address If not found this packet will be forwarded to all the other ports except the port which this packet comes in And these ports will transmit this packet to the network it connected If found and the destination address is located at different port from this packet comes in the Ethernet Switching will forward this packet to the port where this destination address is located according to the information from address table But if the destination address is located at the same port with this packet comes in then this packet will be filtered Thereby increase the network throughput and availability 3 4 Store and Forward Store and Forward is one type of packet forwarding techniques A Store and Forward Ethernet Switching stores the incoming frame in an internal buffer do the complete error checking before transmission Therefore no error packets occurrence it is the best choice when a network needs efficiency and stability
12. witch a bridge or a hub a straight or crossover cable is necessary Each port of the Switch supports auto MDI MDI X detection That means you can directly connect the Switch to any Ethernet devices without making a crossover cable The following table and diagram show the standard RJ 45 receptacle connector and their pin assignments RJ 45 Connector pin assignment Contact met Te cun Media Dependant Interface Interface rece 1 Tx transmit RX receive 2 Tx transmit RX receive Rx receive TX transmit 4 5 Not used 6 RX receive TX transmit 7 8 Not used The standard cable RJ 45 pin assignment A 2 RJ 45 Plug Jack pin out The standard RJ 45 receptacle connector There are 8 wires on a standard UTP STP cable and each wire is color 15 1 coded The following shows the pin allocation and color of straight cable and crossover cable connection 12345678 SIDE 1 4 wWhite Orange 1 White Orange 2 Orange 2 0 3 White Green 3 White Green 4 Blue 4 Blue 5 White Biue 5 White Blue 1234567988DE2 6 Green 6 Green 7 White Brown 7 White Brown 8 Brown 8 Brown Cross Over Cable SIDE 1 SIDE 2 123456788SIDE1 1 White Orange 1 White Green 2 Orange 2 Green 3 White Green 3 White Orange 4 Blue 4 Blue 5 White Blue 5 White Blue 12346567 8SIDE2 6 Green 6 Orange 7 White Brown 7 White Brown 8 Brown 8
13. y shape plastic models and just right for your network of 10 to 50 users The SW 504 SW 804 Desktop Fast Ethernet Switch is a Simple and cost effective highly reliable network Switch And it is the ideal device for bridging Ethernet to Fast Ethernet workgroups or networks Therefore the Switches will be the fast being recognized as one of the most important building blocks for today networking technology To segment the network ease the network traffic the 5 8 Port 10 100Mbps are useful for the SOHO switched networks as the friendly network backbone Provides array LED indicators the network status can be monitored at a glance 2 1 1 Product Overview PLANET SW 504 SW 804 are Desktop Fast Ethernet Switches with 5 8 RJ 45 10 100Mbps ports for high speed network connectivity The Switches can also automatically identify and determine the correct transmission speed and half full duplex mode of the attached devices with its 5 8 ports This Desktop Fast Ethernet Switch also supports store and forward forwarding scheme to ensure low latency and high data integrity eliminates unnecessary traffic and relieves congestion on critical network paths With an intelligent address recognition algorithm the switches could recognize up to 1K different MAC address and enables filtering and forwarding at full wire speed 2 1 2 Switch Front Panel Figure 2 1 amp 2 2 show the front panel and rear panel of SW 504
Download Pdf Manuals
Related Search