Philips 17PF9946/37 Flat Panel Television User Manual
Contents
1. AUDIO CABLES VIDEO CABLES RED WHITE Green Blue Red The CVI connection will be dominate over the AV1 in Video Input When a Component Video Device is con nected as described it is best not to have a video signal connected to the AV1 in Video Input jack ACCESSORY DEVICE EQUIPPED WITH COMPO NENT VIDEO OUTPUTS HELPFUL HINT The description for the component video connectors may differ depending on the DVD player or accessory digital source equipment used for example Y Pb Pr Y B Y R Y Y Cr Cb Refer to your DVD or dig ital accessory owner s manual for definitions and connection details HD HIGH DEFINITION INPUTS igs BOTTOM OF TY f your using a High Definition receiver that can transmit high definition programming the TV can except those signals through the HD Inputs located on the bottom of the TV For Digital Connection connect the HDMI connector of the HD Receiver or similar device to the HDMI Input jacks on the bottom of the TV OR For Analog Connection use Component Video cables to connect the Component Y Pb Pr Video Out jacks of the HD Receiver or similar device to the VGA adapter supplied with the TV Connect the other end of the adapter to the VGA Input jacks on the bottom of the TV Connect the red and white audio adapter to RCA type Audio Cables Connect the audio adapter to the PC HD Audio Input jack on the bottom of the TV 4 Turn the TV a2. SURF button you can quickly view the select channels HOOKING UP THE TELEVISION REMOTE CONTROL BATTERIES f 1o load the supplied batteries into the remote 1 2 3 Remove the battery compartment door on the back of the remote After removing the plastic isolation sheet from the battery place the battery 3V in the remote Be sure the and ends of the batteries line up correctly the inside of the case is marked Reattach the battery compartment door C ABLE IC ABLE Box TV Direct Cable Connection ye Cable TV input into your home may be a single 75 ohm cable or use a cable box decoder In either case the connec tion is very simple Follow the steps below to connect your cable signal to your new television Direct Cable Connections This connection will supply Stereo sound to the TV 1 Cable Box w RF In Outputs This connection will NOT supply Stereo sound to the TV The sound from the cable box will be mono 1 2 3 NOTE Be sure to set the OUTPUT CHANNEL SWITCH on the back of the cable box to CH 3 or 4 then tune the cable box on the TV to the corresponding channel Once tuned change channels at the cable box not the television Connect the open end of the round Cable Company sup plied cable to the 75Q input on the bottom of the TV Screw it down finger tight Connect the open end of the round Cable Company sup plied cable to the cable signal IN put plug on the back of the Cable
3. Box Using a separate round coaxial cable connect one end to the OUT put TO TV plug on the back of the Cable Box Connect the other end of the round coaxial cable to the 75Q input on the bottom of the television Screw it down fin ger tight Cable Box w Audio Video Outputs This connection will supply Stereo sound to the TV 1 2 3 Connect the open end of the round Cable Company sup plied cable to the cable signal IN put plug on the back of the Cable Box Using an RCA type Video Cable connect one end of the cable to the Video yellow or ANT your cable box may be labeled differently Out jack on the cable box and the other end to the Video end of the composite adapter included with the TV Using an RCA type Audio Left and Right Cable connect one end to the left and right Audio Out L amp R jacks red amp white on the cable box Connect the other ends to the Audio end of the composite adapter cable included with the TV Connect the adapter into the AV In jack on the bottom of the TV NOTE Use the AV button and the Number 1 button on the TV remote control to tune to the AV1 channel for the cable box signal Once tuned change channels at the cable box not the television Pressing the AV button repeatedly will scroll all the AV Input chan nels including the presently tuned channel Remote Control shown from the bottom Be sure to point the remote at the remote sensor window on the fron
4. PHILIPS CONTENTS Important Notice Warning 0 1 LCD Stand Assemble 0 1 Basic TV Operation 0 0 00 e eae 1 Remote Control Button Descriptions 1 Hooking up the Television Remote Battery Installation 2 Basic Cable Cable Box TV Connections 2 Basic Antenna TV Connections 2 AV1 Input Connections Component Video Input Connections High Definition Input Connections PC Monitor Connection AV2 Input Connections AV3 Input Connection Monitor Output Connections Quick Use and Hookup Guide IMPORTANT NOTE This owner s manual is used with several different television models Not all features and drawings discussed in this manual will necessarily wees 3 match those found with your television set This is diate 4 normal and does not require that you contact your ae 4 dealer or request service sani 4 WARNING TO PREVENT FIRE OR SHOCK 4 HAZARD DO NOT EXPOSE THIS UNIT TO RAIN OR EXCESSIVE MOISTURE yj om E e Dim BAO 15 7 Wale First assemble the LCD TV using the steps below LCD TELEVISION his LCD television has a set of controls located on the side of the cabinet for use when the remote control is not needed After you have connected the power cord to the TV and plugged the cord into a wall outlet press the POWER button on the front of the TV cabinet to turn the TV ON Press the VOLUME b
5. Sound control Choose from three factory set controls VOICE MUSIC and THEATRE and a PERSON AL to tailor the TV sound to enhance the particular type of program you are watching Number Buttons Press the number buttons for direct access to the TV channels For a 2 digit channel enter the 2nd digit before the dash disap pears For a 3 digit channel enter the first digit followed the next 2 digits AV Source Button Press AV button followed by the Number 1 2 or 3 Number allows you to select AV1 CVI Number 2 to select AV2 channel and Number 3 to select Rear channel fxr 000o CHANNEL 0 VOLUME C TV DVD AUX ACC SELECT SLEEP e DOOM m a gt gt D Ceo C p G FORMAT C cc PROGRAM LIST 3139 125 31933 ok Volume and Channel buttons are located on the side of the television cabinet PHILIPS TV DVD AUX ACC Select Button Press button repeatedly to select the required device mode to perform the activities for the selected device PIP Record Button When in TV mode you can call up a PIP window for the PC Likewise when in PC mode you can call up a PIP window for TV channels When in VCR mode press button to do recording Pixel Plus Pause Il Button When in TV mode this button has no funct
6. ideo inputs provide the highest possible color and picture resolution in the playback of digital signal source material such as with DVD players Connect the Component Y Pb Pr Video OUT jacks from the DVD player or similar device to the COMP onent VIDEO Input Y green Pb blue Pr red jacks on the bottom of the TV When using the Component Video Inputs it is best not to connect a signal to the AV1 in Video Jack Connect the red and white AUDIO CABLES to the Audio left and right output jacks on the rear of the acces sory device to the Audio Adapter supplied L and R Connect the adapter into the AV1 In Input Jacks on the TV Turn the TV and the DVD or digital accessory device ON Press the AV button and the Number 1 button on the remote control to select the CVI channel CVI will appear in the upper left corner of the TV screen Insert a DVD disc into the DVD player and press the PLAY gt button on the DVD Player Ul AW N NOTE When using additional accessories only one external source will be audible as there is only one AV1 Input jack UNE TO AV1 CHANNEL BOTTOM OF TV AUDIO IN RED WHITE VIDEO IN YELLOW mE 7 4 VCR or accessory device boo E avi 2 eo ue yan our EQUIPPED WITH VIDEO AND AUDIO OUTPUT JACKS BACK OF VCR or Accessory device D BOTTOM OF TV COMPONENT
7. ion When in VCR VCD DVD mode press button to do pause the programme you are watching Press button again to release pause mode HD High Definition Mode gt gt button Press to directly enter HD mode Also press to begin playback of a video tape or CD DVD disc CC Button Press to select Closed Captioning options within the menu FM Radio Mode gt button Press to directly enter Radio mode Also press to begin playback of a video tape or CD DVD disc Cursor Buttons Left Right Up Down Press these buttons to highlight select and adjust items on the TV s onscreen menu Program List OK Button When in TV mode press to display a list of channel numbers Each channel will appear as a selectable menu item When in Accessory mode it confirms selections or adjustments in Accessory device Channel or Buttons Press to access the next or previous chan nel Auto Picture Button Press to select an AutoPicture control Choose from four factory set controls MOVIES SPORTS WEAK SIGNAL and MULTI MEDIA and a PERSONAL control that you set according to your own preferences through the onscreen PICTURE menu The four factory set controls will tailor the TV picture so as to enhance the particular type of program you are watching or to improve the picture of a program that has a weak signal Surf Button Press to select previously viewed channels You can place up to 10 channels in memory Then by pressing the
8. nd right PC HD Input Jacks on the bottom of the TV 3 Turn the TV and the Computer ON Press the PC Mode button to set the TV into the HD 4 Mode and tune to the computer s signal Note Please contact your dealer or Philips at 800 531 0039 for information about purchasing the needed cables AUDIO ADAPTER DVI CABLE OR VGA CABLE eu eee ee Se 22S ee ee i bes are Audio Video Input Jacks located on bottom of the TV can also be used for extra accessory device connections for items such as cameras or gaming Stations Connect the VIDEO yellow adapter cable to the VIDEO AV2 in jack on the left rear of the TV Connect the other end of the VIDEO yellow cable to an RCA type VIDEO Cable Connect that cable to the VDEO OUT jack on the back of the accessory device being used Note An S Video cable can be used in place of the yellow Video cable if your device is equiped with an S Video Output S Video provides better video playback Connect the AUDIO red and white adapter cable to an RCA type Audio Cable Connect the other ends of the AUDIO red and white cables to the AUDIO left and right OUT jacks on the rear of the accessory device being used Turn the accessory device and the TV ON Press the AV button and the number 2 button on the remote control to select the AV2 channel for the accessory device AV2 will appear in the upper left corner on the TV screen when tu
9. nd the HD Receiver ON Press the HD Mode button to set the TV into the HD Mode and tune to the HD signal Note The Audio Video cables needed for this connection are not supplied with your TV Please contact your dealer or Philips at 800 531 0039 for information about purchasing the needed cables COMPONENT VIDEO CABLES Green Blue Red Digital Connection CABLES g uy a l 9 a an ye sv IN FROM ANT ag i m z Coxial Cable Lead in fom i Rear of HD Receiver Illustration is Cable Outlet Cable Converter ae for reference only Your HD Box or VHF UHF Antenna Receiver s jack panel may be labeled differently Coaxial cable Lead in from Satellite Dish or Antenna HD RECEIVER EQUIPPED WITH COMPONENT VIDEO OUTPUTS mw ole i em ane a BMA eo PC MONITOR eS his TV can be used as a PC Monitor Your computer will have to be equipped with a VGA type video output and VGA cable Connect one end of the VGA Video cable to the Monitor video output on the computer to the PC Input VGA jack on the bottom of the TV You can use the DVI cable if your computer has DVI capability Although audio connections are not required the TV can reproduce the computers audio out by an AUDIO ADAPTER to the Audio output jack on the computer if available while connecting the other ends of the Audio cables to the Audio In left a
10. ned properly With the accessory device ON press the PLAY button to acti vate the playback on the television Ul AW N ACCESSORY DEVICE Camera DVD VCR etc JACK PANEL BOTTOM OF TV VIDEO CABLE AUDIO CABLES Left and Right AUDIO ACCESSORY DEVICE RIGHT LEFT JACK PANEL AV3 SIDE INPUTS uch like the AV2 jacks the AV3 jacks allow for extra accessory device connections for items such as cameras or gaming stations The AV3 Input Jacks are located on the side of the TV 1 Connect the VIDEO yellow adapter cable to the VIDEO AV3 in jack on the left rear of the TV Connect the other end of the VIDEO yellow cable to an RCA type VIDEO Cable Connect that cable to the VIDEO OUT jack on the back of the accessory device being used Note An S Video cable can be used in place of the yellow Video cable if your device is equiped with an S Video Output S Video provides better video play back Connect the AUDIO red and white adapter cable to an RCA type Audio Cable Connect the other ends of the AUDIO red and white cables to the AUDIO left and right OUT jacks on the rear of the accessory device being used Turn the accessory device and the TV ON Press the AV button and the number 3 button on the remote control to select the AV3 channel for the accessory device REAR will appear in the upper left corner on the TV screen when tuned properly With the acce
11. ntenna wire is threaded screw it down finger tight 2 300 to 75 ohm Adapter Outdoor or Indoor Antenna Combination VHF UHF The combination antenna receives normal broadcast channels 2 13 VHF and 14 69 UHF Twin Lead Wire Round 1750 Coaxial Cable from Antenna Jack Panel Bottom of TV HOOKING UP THE TELEVISION AV I INPUTS he audio video input jacks on the bottom panel of the TV are for direct picture and sound connections between the TV and a VCR or similar device that has audio video output jacks Connect the AV1 In put cable to one end of an RCA 1 type VIDEO yellow cable to the supplied Audio Video adapter Connect the other end of the Adapter to the AV1 in jack on the bottom of the TV Connect the AV1 In put cable to one end of the RCA type AUDIO red and white cables to the supplied Audio Video adapter Turn the VCR or accessory device and the TV On Press the AV button and the number 1 button on the remote control to select the AV1 channel for the accessory device AV1 will appear in the upper left corner on the TV screen when tuned properly You can also press and hold the AV button to toggle through the various channels until AV 1 appears on the screen aa GJ Ro With the VCR or accessory device ON and a prerecorded tape CD DVD etc inserted press the PLAY button to view the tape on the television UT COMPONENT CVI INPUTS Yomponent V
12. ssory device ON press the PLAY button to acti vate the playback on the television Ul AW N MONITOR OUTPUTS S VIDEO JACK PANEL SIDE OF TV VIDEO CABLE Oe S VIDEO CABLE ACCESSORY DEVICE JACK PANEL ACCESSORY DEVICE Camera DVD VCR etc AN S VIDEO CABLE CAN BE USED IN PLACE OF THE YELLOW VIDEO CABLE IF DESIRED e Monitor Audio Video out jacks are great for recording with a VCR or used to connect an external audio system for better audio For Audio System Connection Connect one end of the R ight and L eft AUDIO Monitor Out jacks located on the right rear of the TV to the R and L audio input jacks on your sound system Turn the TV and audio system ON TV sound can be heard through the audio system AUDIO L eft and R ight Sa wall CO ZF DATA AUDIO CABLES Red amp White AUDIO SYSTEM with AUDIO INPUTS
13. t of the television when using the remote control to operate the television Lithium battery 3V Battery Compartment Door NOTE The plastic isolation sheet must be removed for the remote control to function Cable signal coming from Cable Company Round 75Q coaxial cable Jack Panel Bottom of TV Cable Box with RF Inputs and Outputs Connection Output Channel Switch Cable Signal IN from the Cable Company Jack Panel Back of Cable Box Round 75Q Coaxial Cable Cable Box with Audio Video Outputs Connection Cable Signal IN from the Cable Company Jack Panel Back of Cable Box with A V Outputs Audio Cables L amp R Red White Video E Yellow A Jack Panel Bottom of TV ANTENNA TV Antenna Connection A antenna receives normal broadcast chan nels VHF 2 13 and UHF 14 69 Your connection is easy because there is only one 75Q ohm antenna plug on the back of your TV and that s where the antenna goes 1 If your antenna has a round cable 75 ohm on the end then you re ready to connect it to the TV If your antenna has flat twin lead wire 300 ohm you first need to attach the antenna wires to the screws on a 300 to 75 ohm adapter Push the round end of the adapter or antenna onto the 75Q ohm plug on the bottom of the TV If the round end of the a
14. utton to increase the sound level or the VOLUME button to lower the sound level Pressing both buttons at the same time will display the onscreen menu After you are in the menu use these buttons to make adjustments or selections 3 Press the CHANNEL or button to select TV chan nels Use these buttons to make adjustments or selections in the onscreen menu REMOTE CONTROL BUTTONS Power Button Press to turn the TV ON and OFF Status Exit Button Press to see the current channel number on the TV screen Also press to clear the TV menu after control adjustments Sleep Button Press to set the TV to automatically turn itself OFF at a given amount of time Active Control Press to optimize the quality of the picture according to the quality of reception TV Mode 144 button Press to directly enter TV mode Also press to rewind a video tape or CD DVD disc during playback Format Button Press to toggle the different screen format options PC Mode m button Press to directly enter PC mode Also press to stop a video tape or CD DVD disc during playback Menu Button Press for the onscreen menu to appear Pressing the menu button after menu selections are made will exit the menu from the TV screen Mute Button Press to turn the TV sound OFF Press again to return the sound to its previous level Volume or Buttons Press to adjust the TV sound level Auto Sound Button Press to select an Auto
Download Pdf Manuals
Related Search