Pelco PMM12A Computer Monitor User Manual
Contents
1. LED POWER gt INDICATOR 2 B h J HORIZONTAL HOLD VERTICAL HOLD POWER ON OFF SWITCH BRIGHTNESS HINGED COVER CONTRAST Figure 3 Location of Controls PMM15A Shown Contrast Control This control adjusts the contrast between the black and white portions of the picture When properly adjusted you will be able to observe a fine gradation between blacks grays and whites Vertical Hold Control Except 20 This control permits adjustment of vertical stability If the picture rolls upward or downward as shown in Figure 4 turn the VERTICAL HOLD clockwise or counterclockwise until the picture stabilizes Horizontal Hold Control Except 20 This control permits adjustment of horizontal stability If the picture tears to the left or right as shown in Figure 5 turn the HORIZONTAL HOLD clockwise or counterclockwise until the picture stabilizes To operate a monitor 1 Make sure a standard 1 0 V peak to peak video signal is applied to the video input of the monitor 2 Press the power switch to turn on the power The power indicator LED will illuminate NG 3 Adjustthe brightness and contrast controls to obtain optimum picture quality Figure 5 Horizontal Tear 8 C2902M 10 02 MAINTENANCE The only maintenance required is to clean the cabinet and screen periodically Us2. 22 2222222222222222 2 2 2 2 24 2 8 4 Nella Oll aaa tU ten eer esce a tenta dde d eam dM d EE 8 5 Sajid 8 LIST OF TABLES Table Page Video Coaxial Cable Wiring 5 lt as sa KT a WE 7 2902 10 02 IMPORTANT SAFEGUARDS AND WARNINGS Before installing your equipment please read the following important safeguards as outlined by Underwriters Laboratories Inc Read Instructions All the safety and operating instructions should be read before the appliance is operated Retain Instructions The safety and operating instructions should be retained for future reference Heed Warnings All warnings on the appliance and in the operating instructions should be followed Follow Instructions All operating and use instructions should be followed Cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning Attachments Do not use attachments not recommended by Pelco as they may cause hazards Water and Moisture Do not use this CCTV product near water for example near a kitchen sink wash bowl bath tub sprinkler in a wet basement or near a swimming pool and the like unless it is specifically marked for use in wet locations Accessories Do not place this CCTV product on an unstable cart stand tripod bracket or table The CCTV product
3. Pelco will repair or replace without charge any merchandise proved defective in material or If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to workmanship for a period of one year after the date of shipment Exceptions to this warranty are obtain a Repair Authorization number RA and provide the following information as noted below 1 Model and serial number Five years on Pelco manufactured cameras 3500 3600 3700 and MC3500 MC3600 2 Date of shipment number Sales Order number or Pelco invoice number Series two years on all other cameras 3 Details of the defect or problem hree years on Genex Series multiplexers server and keyboard Wo years on cameras and all standard motorized or fixed focal length lenses If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions wo years on Legacy Camclosure Camera Systems 6700 6800 8500 9500 stated above please include a written explanation with the product when returned CM9740 CM9760 Matrix DF5 and DF8 Series Fixed Dome products wo years on Spectra Esprit and PS20 Scanners including when used in continuous Method of return shipment shall be the same or equal to the method by which the item was received by motion applications Pelco wo years on WW5700 series window wiper excluding wiper blades Eighteen months on DX Series digital video recorde
4. may fall causing serious injury to a child or adult and serious damage to the appliance Use only with a cart stand tripod bracket or table recom mended by Pelco or supplied by Pelco with the product When mounting the appliance follow Pelco s installation instructions and use only mounting accessories recommended by Pelco Cart amp Stand An appliance and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the appliance and cart combination to overturn Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the CCTV product and to protect it from overheating These openings must not be blocked or covered The openings should never be blocked by placing the CCTV product on furniture carpet or similar surfaces The CCTV product should never be placed near or over radiators or heat registers This CCTV product should not be placed in a built in installation such as a book case or rack unless proper ventilation is provided or Pelco s installation instructions are adhered to Power Sources This CCTV product should only be operated from the type of power source indicated on the marketing label If you are not sure of the type of power supply to your installation location consult your local electrical building official or power company Refer to the operating instructions for appliances intended to operate from battery or other power
5. INSTALLATION OPERATION PMM9A PMM12A PMM15A PMM20A Monochrome Monitors 4 LISTED C2902M 10 02 Section Page IMPORTANT SAFEGUARDS AND WARNINGS 2 2 222222 2 2 2 5 24 4 4 4 6 aps 6 6 MOUNINO ERE E ei 6 He pa 255 2222 6 SINGEE MONITOR INSTALLATION notre gard ERE Y EDIT ID der 6 MULTIPLE MONITOR INSTALLATION RR I e 22 2 7 8 MAINTENANCE pr es 9 SPEGIFIGATIONS 10 REGULATORY NOTICES 11 WARRANTY AND RETURN INFORMATION nnb eere Dr ete dee e dede deed adi 11 2 C2902M 10 02 LIST OF ILLUSTRATIONS Figure Page 1 Singe Monitor Installation PMM15A Shown 2 2 2 2 6 2 Multiple Monitor Installation PMM15A 2 2 2 2 2 2 2 7 3 Location of Controls PMM15A 5
6. e a damp cloth to clean the screen Use mild soap and water to clean the cabinet Some common household aerosol sprays cleaning agents solvents or polishes may damage the cabinet finish Dry the cabinet with a soft cloth C2902M 10 02 9 SPECIFICATIONS ELECTRICAL Input Voltage Power Consumption PMM12A 5 20 Input Signal Input Impedance Bandwidth Resolution Linearity Horizontal Vertical Operating System CCIR GENERAL Environment Construction Finish Dimensions PMM12A PMM15A PMM20A Picture Tube Dimension PMM12A PMM15A PMM20A Operating Temperature Storage Temperature Relative Humidity Weight PMMS9A PMM12A PMM15A 20 96 256 VAC 50 60 Hz auto ranging 28W 30W 35W 48W 0 5 to 2 0 Vp p composite video 75 ohms or high switchable 100 Hz to 10 MHz 1 000 lines 1096 maximum 1096 maximum Horizontal 15 750 Hz 3400 Hz Vertical 60 Hz Horizontal 15 625 Hz 3400 Hz Vertical 50 Hz Indoor Steel cabinet with black plastic front Black matte texture coat finish 9 3 H x 8 7 W x 9 9 D inches 23 5 x 22 0 x 25 2 cm 12 3 H x 12 2 W x 12 0 D inches 31 3 x 31 0 x 30 5 cm 12 8 H x 14 3 W x 13 1 D inches 32 6 x 36 2 x 33 2 cm 18 6 H x 19 3 W x 14 2 D inches 47 3 x 49 0 x 36 1 cm 9 inches 22 86 cm measured diagonally 12 inches 30 48 cm measured diago
7. een spilled or objects have fallen into the CCTV product c If the CCTV product is not marked Suitable for Wet Locations and it has been exposed to rain or water d If the CCTV product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and often will require extensive work by a qualified technician to restore the CCTV product to its normal operation e If the CCTV product has been dropped or the cabinet has been damaged When the CCTV product exhibits a distinct change in performance this indicates a need for service Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by Pelco or have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards Safety Checks Upon completion of any service or repairs to this CCTV product ask the service technician to perform safety checks to determine that the CCTV product is in proper operating condition WARNING This product has been evaluated for INDOOR USE ONLY unless it bears the marking FOR USE IN WET LOCATIONS WARNING To reduce the risk of electric shock hazard do not remove the cover of the unit This unit can not be serviced by the user and must be sent to a qualified service person for repair
8. fer to the instructions with the mount CONNECTIONS SINGLE MONITOR INSTALLATION Refer to Figure 1 and Table A for the following instructions 1 Set the impedance switch on the back of the monitor to LO 75 ohms 2 Connect a 75 ohm video cable from the video source such as a camera to the BNC connector labeled VIDEO IN or INPUT on the back of the monitor 3 Plug in the appropriate power cord OUTPUT 75 OHM S 2 TERMINATION REAR PANEL OF MONITOR SWITCH Figure 1 Singe Monitor Installation PMM15A Shown C2902M 10 02 MULTIPLE MONITOR INSTALLATION Refer to Figure 2 and Table A for the following instructions 1 Connect a 75 ohm video cable from the video source such as a camera to the BNC connector labeled VIDEO IN or INPUT on the back of the first monitor 2 Connect a 75 ohm video cable from the VIDEO OUT or OUTPUT connector on the back of the first monitor to the VIDEO IN or INPUT connector on the second monitor 3 Ifyou are using a third monitor connect a 75 ohm video cable from the VIDEO OUT or OUTPUT connector on the back of the second monitor to the VIDEO IN or INPUT connector on the third monitor NOTE multiple monitor installations a maximum of three monitors can be connected together 4 Set the impedance switch on the first monitor to HI If you are only using two monitors set the impedance switch on the second monitor to LO 75 ohms If you are using
9. nally 15 inches 38 10 cm measured diagonally 20 inches 50 80 cm measured diagonally 32 to 122 F 0 to 50 C 14 to 140 F 10 to 60 C 10 to 95 percent non condensing 10 45 Ib 4 75 kg 17 50 Ib 7 94 kg 24 15 Ib 10 94 kg 44 25 Ib 20 08 kg Design and product specifications subject to change without notice C2902M 10 02 REGULATORY NOTICES NOTE This equipment has been tested and found to comply with the limits of a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try and correct the interference by one or more of the following measures e the separation between the equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help WARRANTY AND RETURN INFORMATION WARRANTY
10. product liability relating 3500 Pelco Way to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no Clovis CA 93612 5699 event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of If you are located outside the continental U S Alaska Hawaii or Puerto Rico Pelco or otherwise Intermediate Consignee Ultimate Consignee American Overseas Air Freight Pelco The above warranty provides the Dealer with specific legal rights The Dealer may also have 320 Beach Road 3500 Pelco Way additional rights which are subject to variation from state to state Burlingame CA 94010 Clovis CA 93612 5699 USA USA REVISION HISTORY Manual Date Comments C2902M 10 02 Original version amp Pelco the Pelco logo Spectra Genex Legacy Esprit and Camclosure are registered trademarks of Pelco Copyright 2002 Pelco All rights reserved C2902M 10 02 11 PELCO World Headquarters 3500 Pelco Way Clovis California 933612 USA USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 www pelco com 1509001 Orangeburg New York Las Vegas Nevada Eindhoven The Netherlands Wokingham United Kingdom Montreal Canada
11. rs RETURNS One year except video heads on video cassette recorders VCRs Video heads will be In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 covered for a period of six months 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA Six months on all pan and tilts scanners or preset lenses used in continuous motion applica number if returned for repair tions that is preset scan tour and auto scan modes All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and California Repairs made necessary by reason of misuse alteration normal wear or accident freight should be prepaid Ship to the appropriate address below are not covered under this warranty If you are located within the continental U S Alaska Hawaii or Puerto Rico Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the Service Department specific use or application made of the Products Pelco s liability for any claim whether based on Pelco breach of contract negligence infringement of any rights of any party or
12. sources Grounding This CCTV product is equipped with a grounding type plug This plug will only fit into a grounding type power outlet This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the grounding type plug since it is provided to ensure your safety Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the appliance Overloading Do no overload wall outlets and extension cords as this can result in a risk of fire or electric shock 4 C2902M 10 02 C2902M 10 02 Object and Liquid Entry Never push objects of any kind into this CCTV product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the CCTV product Servicing Do not attempt to service this CCTV product yourself as opening or removing covers may expose you to dangerous voltages or other hazards Refer all servicing to qualified service personnel Damage Requiring Servicing Unplug this CCTV product from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the power supply cord or plug is damaged b If liquid has b
13. three monitors set the impedance switch on the second monitor to HI and on the third monitor to LO 75 ohms 5 Plug in the appropriate power cords for the monitors MONITOR 1 MONITOR 2 MONITOR 3 IMPEDANCE SWITCH SET IMPEDANCE SWITCH SET HI IMPEDANCE SWITCH SET FROM VIDEO SOURCE TO INPUT FROM OUTPUT TO INPUT FROM OUTPUT TO INPUT NOTE SET IMPEDANCE SWITCHES AS APPROPRIATE FOR THE NUMBER OF MONITORS IN YOUR CONFIGURATION 15 0HM TERMINATION SWITCH REAR PANEL OF MONITOR Figure 2 Multiple Monitor Installation PMM15A Shown Table A Video Coaxial Cable Requirements RG59 U 750 ft 229 m RG6 U 1 000 ft 305 m RG11 U 1 500 ft 457 m Minimum cable requirements 75 ohms impedance All copper center conductor All copper braided shield with 9596 braid coverage C2902M 10 02 OPERATION Controls are located on the front of the monitor On the PMM9A PMM12A and PMM15A some or all of the controls are behind a hinged cover Refer to Figure 3 Power On Off Switch This rocker switch turns the power on or off Push the side with the white line to turn on the power Push the side with the white circle to turn the power off LED Power Indicator The LED lights when power is turned on Brightness Control This control adjusts the overall picture brightness to compensate for differences in room lighting
14. when it fails to function The lightning flash with an arrow head symbol within an equilateral triangle means that if the enclosure is opened electrical circuitry is exposed which imposes an electric shock hazard to persons present The exclamation point within an equilateral triangle means the operating instructions contain important information on how to operate and maintain the appliance DESCRIPTION The PMM9A PMM12A PMM15A and 2 are high resolution black and white CCTV video monitors The cabinets are made of steel for ruggedness and with the exception of the picture tube the circuitry is all solid state for reliability MODELS PMM12A PMM15A PMM20A Black and white monitor 9 inch 22 86 cm picture display 96 256 VAC 50 60 Hz EIA CCIR auto sensing Same as PMMS9A except 12 inch 30 48 cm picture display Same as PMMS9A except 15 inch 38 10 cm picture display Same as PMMS9A except 20 inch 50 80 cm picture display INSTALLATION The following parts are supplied Monitor Two power cords 1 USA standard and 1 European standard MOUNTING The monitor has rubber feet and may be placed on any horizontal surface such as a desk or table The monitor also can be mounted to a wall or ceiling with an appropriate mount If you have a PMM9A PMM12A or PMM15A monitor it can be installed in a 19 inch equipment rack with a suitable rack mounting kit For mounting to a wall or ceiling or in a rack re
Download Pdf Manuals
Related Search