Home

Pelco FR8302A Marine Radio User Manual

1. UTP CABLE OR e Sm coava CABLE Figure 5 FR8302A Receiver Connections C1649M 1 06 13 Troubleshooting LED indicators on the front panel of the FR8302A receiver refer to Figure 2 allow you to monitor signal status and operating power Table A provides information about the front panel indicators and associated troubleshooting guidelines NOTE For troubleshooting information indicated by the LEDs on the associated FT8301A FT8301 transmitter refer to the manual supplied with the transmitter Table A Troubleshooting with Front Panel Indicators Indicator Color Possible Cause Corrective Action Power LED Pelco badge Blue Pelco logo lights Power is being applied to the module 0 action required Blue Pelco logo does not light Power is not being applied to the module Power connection is faulty Check power connection f module is rack mounted reseat module or power supply as necessary Power supply has failed Replace power supply Loss of power occurs due to tripped circuit breaker s blown fuse s or faulty electrical service Check circuit breaker s use s or electrical service as necessary Video Present LED Green Incoming video signal No action required is present on the channel Red Incoming video signal Optical signal is not
2. lt lt FLANGE 2 _ VERTICAL MOUNTING HOLE 2 S lt HORIZONTAL MOUNTING HOLE 2 4 LOWER SCREW PHILLIPS WALL CLIP FLANGE PAN HEAD WITH LOCK WASHER 2 amp Figure 4 Mounting the FR8302A Receiver to a Wall Using the Wall Clip C1649M 1 06 CONNECTIONS Connections to the FR8302A receiver are made on the rear panel of the module and consist of the following Power connection NOTES A12VDC or 24 VAC power supply can be used to power the receiver when used as a standalone module A 12 VDC power supply is provided If a 24 VAC power supply is used the power supply must be a Listed Direct Plug In Power Unit marked as Class 2 and rated as 24 VAC 200 mA minimum output extreme temperature conditions it is recommended that an industrial rated outdoor power supply such as the Pelco WCS1 4 power supply be used Fiber connection per channel Video output connection UTP or BNC per channel NOTE When connecting to the UTP connector it is recommended that solid UTP wire rather than stranded UTP wire be used If stranded UTP wire is used it is recommended that you tin the stranded wire Figure 5 illustrates FR8302A receiver connections POWER ALARM CONNECTION FOR RACK MOUNTED MODULE POWER CONNECTION lt Hi FOR STANDALONE MODULE FIBER OPTIC CABLE UTP CABLE OR BM coava ceu am FIBER OPTIC CABLE
3. Refer to the Optic Fault LED is not present onthe being received from troubleshooting section channel the transmitter Optic below Fault LED is also red Video source is not Check power connection to powered on the video source Video source is not Check BNC connections connected to the transmitter Coaxial cable Replace cable connected to the transmitter is defective Continued on next page 14 C1649M 1 06 Table A Troubleshooting with Front Panel Indicators Continued not being received from the transmitter C owered on Fiber optic cable is not onnected Indicator Color Meaning Possible Cause Corrective Action Optic Fault LED Green The optical signal is No action required being received from the transmitter Red The optical signal is Transmitter is not Check power connections Replace power supply if necessary Check fiber optic connections C Fiber optic cable onnectors are dirty or re damaged Clean polish or replace fiber optic cable connectors as necessary d iber optic cable is efective Replace cable b A problem exists with he optical power udget Verify that losses in fiber optic cable do not exceed the optical power budget specification of the fiber optic link If the losses do exceed the optical power budget contact Product Support C1649M 1 06 Specifications VIDEO Num
4. is required for operation in environments with relative humidity above 95 condensing No performance adjustments required 12 VDC or 24 VAC power supply LED indicators for monitoring of signal status and operating power The FR8302A receiver is a Class 1 laser product that complies with FDA radiation performance standard 21CFR Subchapter J and with IEC 60825 1 Edition 1 2 2001 08 C1649M 1 06 MODELS The FR8302A fiber receiver consists of the following series of models Multimode Models FR8302AMSTR 2 Two channel fiber optic video receiver multimode ST connector transmission distance up to 2 km compatible with FT8301AMSTR FT8301AMST and FT8301MST transmitters FR8302AMSTRE 2 Two channel fiber optic video receiver multimode ST connector transmission Single Mode Models FR8302ASSTR 2 FR8302ASFCR 2 distance up to 6 km extended distance compatible with FT8301 AMSTRE FT8301AMSTE and FT8301MSTE transmitters Two channel fiber optic video receiver single mode ST connector compatible with FT8301ASSTR FT8301ASST and FT8301SST transmitters Two channel fiber optic video receiver single mode FC connector compatible with FT8301ASFCR FT8301ASFC and FT8301SFC transmitters For conformal coated models replace the first letter F in the model number with the letter C The conformal coated version of FR8302AMSTR 2 for example is CR8302AMSTR 2 OPTIONAL ACCESSORIES The following optiona
5. 46 km 28 6 15 6 mW FT8301 ASST FT8301SST FR8302ASFCR 2 FT8301 ASFCR 1310 nm 28 dB 46 km 28 6 15 6 mW FT8301ASFC FT8301SFC The FR8302A receiver and compatible transmitters are classified by th When using 50 125 um multimode fiber subtract 3 d Maximum transmission distance is limited by fiber bandwidth transmission distance is based on attenuat and splice losses NOTES For conformal coated models replace the first let The conformal coated version of FR8302AMSTR 2 for example is CR8302AMSTR 2 B from the optical power budget For models with higher optical power budgets contact the factory e FDA as Class 1 laser products ion of 0 5 dB km plus a 5 dB buffer for connector er F in the model number with the letter C C1649M 1 06 gt lt This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002 96 EC of the European Union regarding the disposal of waste electrical and electronic equipment WEEE Contact your local dealer for procedures for recycling this equipment C1649M 1 06 PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below Five years on FT FR8000 Series fib
6. INSTALLATION FR8302A Fiber Receiver Two Channel Digitally Encoded Video C1649M 1 06 Contents Important Safety Instructions e ee 4 Regulatory NOTICES 2 22 0555s ee Mae ahead ok xb e eaa hiddan 6 Product QVervIgW LO Sur ee 7 DGSCHDUOR 7 Models nade cte ttem quere end an x 8 Optional ACCessories ev ee ect que RETINA 8 Erorib Patel Berens b REOR BER Re 9 Rear Parel ce a Re Pede sette HERO Rei 10 Installation s ios d tex eme OPES bg 11 Package Contents eere Re emm oneview dane oan 11 Mounting it eot BL buts ise a Cede citet 11 Mounting the FR8302A Receiver into a Rack 11 Mounting the FR8302A Receiver to a 11 GOMMECT OMS estt niunt Gua D aa erp iei m rS 13 ett t eee re Rn ADIRI RR RM yee 14 Specifications coeur S EPIS REM RE AM Oi ee ee eee 16 List of Illustrations 1 Two Channel Video Transmission Using FR8302A Receiver 7 2 Front Panel of FR8302A Receiver 9 3 Rear Panel of FR8302A 10 4 Mounting the FR8302A Receiver to a Wall Using the Wall Clip 12 5 FR8302A Receiver Conn
7. ack mount chassis which can be mounted into an industry standard 19 inch 48 26 cm equipment rack The RK5000 Series rack mount chassis includes the following models RK5000PS 3U and RK5000 3U Designed to accommodate fiber optic modules as follows RK5000PS 3U rack mount chassis provides 12 module slots and a power supply RK5000 3U rack mount chassis provides 14 module slots a power supply is not included Power to the modules can be supplied using the optional external power supply EPS5000 120 For additional information refer to the RK5000PS 3U RK5000 3U Fiber Rack Mount Chassis Installation manual RK5000PS 5U Designed to accommodate Endura modules but can also accommodate fiber optic modules with the use of the RK5001 1UEXP adapter kit The RK5001 1UEXP adapter kit is required for installation of the FR8302A receiver into the 5000 5 50 chassis For information about the RK5000PS 5U chassis refer to the RK5000PS 5U Rack Mount Chassis Installation manual MOUNTING THE FR8302A RECEIVER TO A WALL The FR8302A receiver can be mounted to a wall in the following ways Using the supplied wall clip for attachment of a single module to a wall For installation instructions refer to the Mounting the FR8302A Receiver Using the Wall Clip section below Using the optional WM5001 wall mount kits which are designed for mounting of single width fiber optic modules The WM5001 3U base kit allows mounting
8. ber of Channels Modulation Type Video Output Bandwidth Gain Differential Gain Differential Phase Tilt Signal to Noise Ratio GENERAL Operating Temperature Input Power Requirements LED Indicators Dimensions Unit Weight MECHANICAL Connectors Video Rack Power Alarm Standalone Power Fiber Optic 2 Pulse code modulation 8 bit resolution BNC 1 0 Vp p 75 ohms or UTP 100 ohms NTSC PAL and SECAM 6 5 MHz Unity lt 2 1 196 60 dB CCIR weighted 40 to 167 F 40 to 75 C 12 VDC or 24 VAC 270 mA Power Video Present per channel Optic Fault per channel 85 Dx 1 08 W x 4 81 22 23 x 2 74 x 12 22 cm 1 58 Ib 0 72 kg BNC per channel UTP 2 pin connector spring cage terminal per channel 4 pin connector 2 pin connector screw terminal ST for multimode fiber per channel ST or FC for single mode fiber per channel C1649M 1 06 OPTICAL POWER BUDGET TRANSMISSION DISTANCE AND LASER CLASS 1 LIMIT Optical Maximum Laser FR8302A Compatible Power Transmission Class 1 Receiver Transmitters Wavelength Budget Distance Limit Multimode 62 5 125 pm FR8302AMSTR 2 FT8301AMSTR 850 nm 20 dB 2 km 1 2 mi lt 0 78 mW FT8301AMST FT8301MST Multimode Extended Distance 62 5 125 pm FR8302AMSTRE 2 FT8301AMSTRE 1310 nm 26 dBt 6 km 3 7 mijit 15 6 mW FT8301AMSTE FT8301MSTE Single Mode 9 125 FR8302ASSTR 2 FT8301ASSTR 1310 nm 28 dB
9. ections 13 List of Tables A Troubleshooting with Front Panel Indicators 14 C1649M 1 06 3 Important Safety Instructions 20 m SO ema ges SIS Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has wo blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the points where they exit from the apparatus Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avo
10. er connection of standalone ing connector with screw terminals not shown FIBER OPTIC CONNECTOR per channel ST or FC dependent on FR8302A model ELDED TWISTED PAIR CONNECTOR per channel 100 ohm differential analog video output 2 pin connector removable mating connector with spring cage terminals not shown VIDEO OUT BNC CON ECTOR per channel 75 ohm analog video output NOTE For each channel the FR8302A receiver provides two video output connectors one UTP connector and one BNC connector For each channel only one of the video output connectors can be used at one time For additional information about rear panel connections refer to the nstallation section C1649M 1 06 Installation PACKAGE CONTENTS The following items are supplied 1 1 1 FR8302A receiver Regulated switching power supply with four plug adapters North American Australian U K and European configurations 100 240 VAC 50 60 Hz input 12 VDC output Wall clip with two 4 40 x 250 inch Phillips pan head screws with lock washers for attachment of single module to wall FR8302A Fiber Receiver Installation manual this manual MOUNTING The FR8302A receiver can be mounted into a rack or can be used as a standalone module As a standalone module the unit can be placed on a desktop or can be mounted to a wall MOUNTING THE FR8302A RECEIVER INTO A RACK The FR8302A receiver can be installed into an RK5000 Series r
11. er optic products Three years on Genex Series products multiplexers server and keyboard e Three years on Camclosure and fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H 2X camera models which have a five year warranty Three years on PMCL 200 300 400 Series LCD monitors Two years on standard motorized or fixed focal length lenses Two years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series fixed dome products Two years on Spectra Esprit ExSite and PS20 scanners including when used in continuous motion applications e Two years on Esprit and WW5700 Series window wiper excluding wiper blades Two years except lamp and color wheel on Digital Light Processing DLP displays The lamp and color wheel will be covered for a period of 90 days The air filter is not covered under warranty Eighteen months on DX Series digital video recorders NVR300 Series network video recorders Endura Series distributed network based video products and TW3000 Series twisted pair transmission products e One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months e months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipmen
12. explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are instructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER SERVICE send the goods to If the goods are to be sent by a FREIGHT FORWARDER send the goods to Pelco Pelco c o Expeditors 3500 Pelco Way 473 Eccles Avenue Clovis CA 93612 5699 USA South San Francisco CA 94080 USA Phone 650 737 1700 Fax 650 737 0933 REVISION HISTORY Manual Date Comments C1649M 1 06 Original version Pelco the Pelco logo Camclosure Esprit Genex Legacy and Spectra are registered trademarks of Pe
13. id injury from tip over Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on the apparatus WARNING To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture Installation should be done only by qualified personnel and conform to all local codes Unless the unit is specifically marked as a NEMA Type 3 35 4 4X 6 or 6P enclosure it is designed for indoor use only and it must not be installed where exposed to rain and moisture Use only installation methods and materials capable of supporting four times the maximum specified load A CCC approved power cord must be used to power this equipment when used in China CAUTION These servicing instructions are for use by qualified service personnel only To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so C1649M 1 06 The product and or manual may bear the following marks AN This symbol indicates that dangerous voltage cons
14. l accessories are available for the FR8302A receiver WM 5001 3U Wall mount base kit for single width module WM5001 3UEXP Wall mount expansion kit for single width module RK5000 3U 19 inch rack mount chassis for 14 slots no power 3 RUs RK5000PS 3U 19 inch rack mount chassis for 12 slots with power 3 RUs EPS5000 120 External rack power supply 1 RU dual 120 W power outputs RK5001B 3U Blank filler panel single width RK5002B 3U Blank filler panel double width RK5001 1UEXP Adapter kit that allows a 3 RU single width fiber module to be used in RK5000PS 5U rack mount chassis C1649M 1 06 FRONT PANEL The front panel of the FR8302A receiver provides LED indicators that allow you to monitor signal status and operating power refer to Figure 2 Figure 2 Front Panel of FR8302A Receiver o VIDEO PRESENT LED per channel 2 OPTIC FAULT LED per channel POWER LED Pelco badge For detailed information about the front panel indicators refer to the Troubleshooting section C1649M 1 06 REAR PANEL Connections to the FR8302A receiver are made to the rear panel of the module refer to Figure 3 Figure 3 Rear Panel of FR8302A Receiver RACK POWER ALARM mounted module STANDALONE POWER module removable ma VIDEO OUT UTP UNSH CONNECTOR 4 pin connector for power alarm connection of rack CONNECTOR 2 pin connector for pow
15. lco Endura and ExSite are trademarks of Pelco Copyright 2006 Pelco DLP is a registered trademark of Texas Instruments Inc All rights reserved PELCO Worldwide Headquarters 3500 Pelco Way Clovis California 93612 USA USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 www pelco com 1509001 United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East
16. mmission s rules This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme la norme NMB 003 du Canada C1649M 1 06 Product Overview DESCRIPTION The FR8302A fiber receiver provides the ability to accept two composite video channels over two optical fibers The FR8302A receiver is compatible with the FT8301A transmitter and is also backward compatible with the FT8301 transmitter Each of two transmitters can send a single independent video channel to one FR8302A receiver refer to Figure 1 ONE VIDEO sio FT8301A FT830 Two 1 1 FIBER TRANSMITTER VIDEO OUTPUTS FR8302A RECEIVER FT8301A FT8301 ONE ONE FIBER VIDEO INPUT Figure 1 Two Channel Video Transmission Using FR8302A Receiver Features of the FR8302A receiver include the following Accepts two 8 bit digitally encoded video channels over two fibers Multimode fiber support for distances up to 6 km 3 7 mi Single mode fiber support for distances up to 46 km 28 6 mi Exceeds all requirements for the RS 250C Medium Haul Transmission specification Compatible with NTSC PAL and SECAM video standards Designed to meet NEMA TS 2 and Caltrans traffic signal control equipment standards for ambient operating temperature mechanical shock and vibration humidity with condensation high line low line voltage conditions and transient voltage protection NOTE Conformal coating
17. of a single module to the wall The WM5001 3UEXP expansion kit allows mounting of an additional module It is recommended that a maximum of three expansion kits be used with the base kit allowing a maximum of four single width modules to be mounted to the wall C1649M 1 06 11 NOTE The WM5001 wall mount kits can be used with the WM5002 wall mount kits which are designed for mounting of double width fiber optic modules If mounting a mix of single width and double width modules is desired it is recommended that a maximum of two single width modules and one double width module be mounted in combination with one another For mounting instructions using the wall mount kits refer to the WM5000 Series Wall Mount Kit Installation manual Mounting the FR8302A Receiver Using the Wall Clip NOTE Before mounting the FR8302A receiver to a wall ensure that there is adequate space at both ends for viewing the front panel LEDs and for making the various rear panel cable connections To attach the FR8302A receiver to a wall using the supplied wall clip refer to Figure 4 and do the following 1 Using the two vertical or horizontal wall mounting holes attach the wall clip to a wall using two screws not provided 2 Slide the module into the clip until the two holes on the bottom of the module align with the two holes on the lower flange of the clip 3 Attach the module to the clip using the two Phillips pan head screws provided for the clip
18. t All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products hall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential amages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state Pa If a warranty repair is required the Dealer must contact Pelco at 800 p289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information Model and serial number 2 Date of shipment PO number Sales Order number or Pelco invoice number 3 Details of the defect or problem there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written
19. tituting a risk of electric shock is present CAUTION ee RISK OF ELECTRIC SHOCK A This symbol indicates that there are important DO NOT OPEN operating and maintenance instructions in the literature accompanying this unit C1649M 1 06 5 Regulatory Notices This devi ce complies wi conditions 1 this devic interfere nce received in h Part 15 of the FCC Rules Operation is subject to the following two e may not cause harmful interference and 2 this device must accept any cluding interference that may cause undesired operation RADIO AND TELEVISION INTERFERENCE This equi pursuant pment has bee n tested and found to comply with the limits of a Class A digital device to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipme accordance with the ins Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense nt generates uses and can radiate radio frequency energy and if not installed and used in ruction manual may cause harmful interference to radio communications Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Co

Pelco FR8302A Marine Radio User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents