Pelco C528M-E Marine Radio User Manual
Contents
1. 1 PT COMMON 1 PT COMMON 3 LEFT 3 LEFT 4 AUTO 4 AUTO 5 DOWN TO SCANNER 5 DOWN I TO PAN TILT UP CONNECTOR 6 UP CONNECTOR 7 RIGHT 7 RIGHT 8 SAFTY GND 8 SAFTY GND 10 IRIS 10 IRIS 20900 TOLENS 700 TO LENS 11 FOCUS CONNECTOR 11 FOCUS CONNECTOR 13 LENS COM 13 LENS COM Figure 5 MPTAZ115DT MPTAZ220DT Wiring Figure 6 MPTAZ115DT MPTAZ220DT Wiring Diagram for Scanners and Lenses Diagram for Pan Tilts and Lenses C528M E 4 03 7 OPERATION To operate the MPTAZ Series Control use the push buttons to control the lens and move the joystick to control the pan tilt or scanner The MPTAZ Series Control has two modes of automatic pan tilt operation random scan and auto scan Random activation causes scanning between the limit stops in an unpredictable pattern To activate random mode press the SELECT switch until the LED next to RANDOM is lit Auto scan will operate the pan tilt between limits for 30 minutes After 30 minutes the control returns to the random scan mode To activate auto scan press the SELECT switch until the LED next to AUTO is lit To return to manual mode move the joystick to the left or right The control will also return to manual operation if power is lost and restored 8 C528M E 4 03 MAINTENANCE Under normal operating conditions and usage maintenance of this equipment is not necessary Howev2. 10 line loss in voltage at the lens motor 22 AWG 0 3 mm 1 062 ft 323 m 20 AWG 0 5 mm 1 688 ft 514 m 18 AWG 1 0 mm 2 686 ft 818 m MPTAZ24DT and MPTAZ24DT 220 Wire the connecting cable from the pan tilt or scanner to the control Refer to one of the following wiring diagrams Figure 2 scanners or Figure 3 pan tilts Proceed to step 3 NOTE When a relay box RB24 RB115 is used with a scanner the AUTO SCAN mode requires special connections consult factory for details PT COMM LEFT RIGHT TO SCANNER UP CONNECTOR DOWN AUTO Z00M dux L TO LENS IRIS CONNECTOR LENS COM SIS SISIS SISISI SG 12 3 4 5 6 7 8 9 10 CONTROLLER OUTPUT TERMINAL STRIP Figure 2 MPTAZ24DT MPTAZ24DT 220 Wiring Diagram for Scanners and Lenses PT COMM LEFT RIGHT TO PAN TILT UP CONNECTOR DOWN AUTO ZOOM TORUS I TOLENS IRIS CONNECTOR LENS COM SIS G S SS S SS 12 3 4 5 6 7 8 9 10 CONTROLLER OUTPUT TERMINAL STRIP Figure 3 MPTAZ24DT MPTAZ24DT 220 Wiring Diagram for Pan Tilts and Lenses C528M E 4 03 MPTAZ115DT or MAPTAZ220DT Assemble the mating connector Refer to Figure 4 and perform the following steps a Slide the connector clamp assembly over the conductor cable If the diameter of the conductor
3. cable is such that the rubber boot will slide over it easily slide the rubber boot onto the conductor cable at this time If not discard the rubber boot b Referto Detail A in Figure 4 Prepare the wires from the conductor cable as follows e Strip at least one inch 2 54 cm from the cable jacket to expose the wires You may need to strip more from the cable jacket if you have more wires e Strip 125 inch 3 mm from each wire e Use an AMP style crimper crimp the wires and their insulation to the connector pins NOTE Contacts cannot be removed from the connector without the use of the appropriate AMP extraction tool 71305183 which is available from Pelco c Slide the connector pins into the appropriate holes in the connector body until they snap into place Refer to detail in Figure 4 and to Figures 5 and 6 for the correct pin arrangement d Push the connector clamp assembly with boot if used toward the connector body Screw the clamp assembly onto the connector body being careful not to disturb the wires e complete the assembly attach the appropriate clamp with the screws provided and tighten f Wire the connecting cable from the pan tilt or scanner to the controller Refer to one of the following wiring diagrams Figure 5 scanners or Figure 6 pan tilts 3 Plug the control s power cord into an AC outlet The unit powers up in manual operation mode the MANUAL LED turns on
4. 3651H 2X MC3651H 2 and MC3651H 2X camera models which have a five year warranty wo years on standard motorized or fixed focal length lenses wo years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series ixed dome products wo years on Spectra Esprit ExSite and continuous motion applications PS20 scanners including when used in wo years on Esprit and WW5700 Series window wiper excluding wiper blades Eighteen months on DX Series digital video recorders NVR300 Series network video recorders and Endura Series distributed network based video products One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months Six months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product ia
5. INSTALLATION OPERATION MPTAZ Series Pan Tilt and Scanner Control 528 4 03 CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS sees tnnt tette ttc 3 DESCRIPTION MODELS om 5 OPERATION m 8 IAIN RENAN 9 SPECIFICATIONS H OUU U OI IeT 10 REGULATORY NOTICES ic cote tmt et een eti i et e n tem ate tace t 11 WARRANTY AND RETURN INEORMATIDN a cree pie te ie etra a ette ec cem ae HR RORIS 11 LIST OF ILLUSTRATIONS Figure Page 1 PC Board Configuration retentis 2 MPTAZ24DT MPTAZ24DT 220 Wiring Diagram for Scanners and Lenses 3 MPTAZ24DT MPTAZ24DT 220 Wiring Diagram for Pan Tilts and Lenses 4 Connector Assemb LI rM ee e 5 MPTAZ115DT MPTAZ220DT Wiring Diagram for Scanners and Lenses 6 MPTAZ115DT MPTAZ220DT Wiring Diagram for Pan Tilts and Lenses c ccccccccstesceseseseesessesessesseseesesssssstssssseesesesessssssssaveseessaeseaneseeseaneass 2 C528M E 4 03 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product the following WARNINGS should be observed 1 Installation and servicing should only be done by qualified service personnel and conform to all local codes 2 Unless the uni
6. bility relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise he above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment P O number Sales Order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing c
7. device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class A digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below Five years on FT FR8000 Series fiber optic products Three years on Genex Series products multiplexers server and keyboard Three years on Camclosure and fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC
8. er if maintenance is required contact a qualified service technician or return to the factory for repair C528M E 4 03 9 SPECIFICATIONS ELECTRICAL Input Voltage PTAZ115DT MPTAZ24DT PTAZ24DT 220 MPTAZ220DT Output Voltage PTAZ24DT MPTAZ24DT 220 PTAZ115DT PTAZ220DT Lens Voltage Fuse Protection PTAZ115DT MPTAZ24DT PTAZ24DT 220 722007 Power Cord Connectors MPTAZ115DT MPTAZ220DT PTAZ24DT MPTAZ24DT 220 Conductor Requirements GENERAL Construction Cover Chassis Panel Approximate Weight MPTAZ115DT MPTAZ220DT MPTAZ24DT MPTAZ24DT 220 120 VAC 50 60 Hz 230 VAC 50 60 Hz 24 VAC 120 VAC 230 VAC 0 12 VDC 1 ASB 0 5 ASB 3 wire grounded 418 AWG AMP CPC type 10 position terminal strip No additional conductors required for auto random scan operation 9 plus ground for MPTAZ115DT or MPTAZ220DT when used with pan tilt and lens 8 plus ground for MPTAZ115DT when used with scanner and lens 9 and no ground for MPTAZ24DT or MPTAZ24DT 220 when used with pan tilt and lens 8 and no ground for MPTAZ24DT or MPTAZ24DT 220 when used with scanner and lens Steel black polyester powder coat Steel zinc plated Aluminum black polyester powder coat with white silkscreen 5 17 Ib 2 34 kg 5 17 Ib 2 34 kg 6 48 Ib 2 94 kg 6 59 Ib 2 99 kg Design and product specifications subject to change without notice C528M E 4 03 REGULATORY NOTICES This
9. harge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are instructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER SERVICE send the goods to Pelco 3500 Pelco Way Clovis CA 93612 5699 USA If the goods are to be sent by a FREIGHT FORWARDER send the goods to Pelco c o Expeditors 473 Eccles Avenue South San Francisco CA 94080 USA Phone 650 737 1700 Fax 650 737 0933 REVISION HISTORY Manual Date Comments C528M 1992 Original version C528M A 10 92 Revised installation instructions added Figure 7 C528M B 10 93 Revised to include MPTAZ24DT 220 C528M C 8 95 Revised Figures 2 and 7 C528M D 11 99 Revised installation instructions Updated manual to new format C528M E 4 03 Revised operation instructions added FCC Class A statement Updated manual to new format Pelco the Pelco Logo Camclosure Esprit Genex Legacy and Spectra are registered trademarks of Pelco This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002 96 EC of the E
10. t meets NEMA Type 3 35 4 4X or 6P standards it is designed for indoor use only and it must not be installed where exposed to rain and moisture 3 Only use replacement parts recommended by Pelco 4 After replacement repair of this unit s electrical components conduct a resistance measurement between line and exposed parts to verify the exposed parts have not been connected to line circuitry The product and or manual may bear the following marks 2 This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit CAUTION RISK OF ELECTRIC SHOCK A This symbol indicates that there are important operating and mainte DO NOT OPEN nance instructions in the literature accompanying this unit Please thoroughly familiarize yourself with the information in this manual prior to installation and operation C528M E 4 03 3 DESCRIPTION The controls in the MPTAZ Series operate 120 VAC 230 VAC and 24 VAC pan tilts or scanners All models include auto random manual scan operation pan tilt operation with a joystick and lens control MODELS MPTAZ24DT MPTAZ24DT 220 MPTAZ115DT MPTAZ220DT Desktop joystick control module for 24 VAC pan tilts and scanners 120 VAC input FCC Class A Same as MPTAZ24DT except 230 VAC input CE Desktop joystick control module for 120 VAC pan tilts and scanners 120 VAC input FCC Class A Desktop joystick control module for 230 VAC pan til
11. ts 230 VAC input C528M E 4 03 INSTALLATION The MPTAZ Series Control is shipped from the factory for pan tilt operation If you are connecting the control to a pan tilt skip step 1 and proceed to step 2 Electrical Connections 1 To operate a scanner with the MPTAZ Series reset the control s jumper JP5 to the SCANNER position Jumper 5 is factory set in the P T position Refer to Figure 1 for the internal configuration of the PC board 10 2 C528M E 4 03 12072 39 EX R7 e R13 se 120 230V MADE IN USA IP Figure 1 PC Board Configuration 00000000 110 006060606 60200000 Ch 5 oec recs gt e z i Boge m m y Om 5 0200200000 e E 29000000 99990000 ule t OT m m 199999099909 eon IPG eovcccce 9 TEST 1 00000900 cH R4 ei e Electrical Connections Follow the correct instructions for your control model Cable Distances Pan Tilt or Scanner Refer to the installation manual for the specific scanner or pan tilt to be used with the control Lens The following lens distances are the approximate maximum recommended under the following conditions e Based on a 35 mA load 12 VDC e Single lens function activation
12. uropean Union regarding the disposal of waste electrical and electronic equipment WEEE Contact your local dealer for procedures for recycling this equipment Endura and ExSite are trademarks of Pelco C528M E 4 03 Copyright 2003 Pelco All rights reserved PELCO Worldwide Headquarters 3500 Pelco Way Clovis California 933612 USA USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 www pelco com 1509001 United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East
Download Pdf Manuals
Related Search