Pelco C1965M-C Car Video System User Manual
Contents
1. Prior to installation and use of this product the following WARNINGS should be observed 1 Installation and servicing should only be done by qualified service personnel and conform to all local codes 2 Unless the unit is specifically marked as NEMA Type 3 35 4 4X 6 or 6P enclosure it is designed for indoor use only and it must not be installed where exposed to rain and moisture 3 Only use replacement parts recommended by Pelco 4 Mfter replacement repair of this unit s electrical components conduct a resistance measurement between line and exposed parts to verify the exposed parts have not been connected to line circuitry The product and or manual may bear the following marks This symbol indicates that dangerous voltage constituting a risk of electric shock is present CAUTION within this unit RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit Please thoroughly familiarize yourself with the information in this manual prior to installation and operation Regulatory Notices This equipment has been tested and found to comply with the limits of a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency ene2. U S Alaska Hawaii or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are instructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER SERVICE send the goods to If the goods are to be sent by a FREIGHT FORWARDER send the goods to Pelco Pelco c o Expeditors 3500 Pelco Way 473 Eccles Avenue Clovis CA 93612 5699 USA South San Francisco CA 94080 USA Phone 650 737 1700 Fax 650 737 0933 Pelco the Pelco logo Camclosure Esprit Genex Legacy and Spectra are registered trademarks of Pelco Endura and ExSite are trademarks of Pelco Copyright 2001 Pelco All rights reserved REVISION HISTORY Manual Date Comments C1965M 6 01 Original version C1965M A 7 01 Modified format and specifications C1965M B 7 01 Revised Front Panel Controls section C1965M C 12 03 Changed specifications and illustrations for BNC connector updated icons 12 Pelco Manual C1965M C 12 03
3. PELLO Installation Operation PMCL15A TFT LCD Monitor C1965M C 12 03 Pelco 3500 Pelco Way Clovis CA 93612 5699 USA www pelco com In North America and Canada Tel 800 289 9100 FAX 800 289 9150 International Customers Tel 1 559 292 1981 FAX 1 559 348 1120 5 Section Page IMPORTANT SAFEGUARDS AND WARNINGS cecesccscescsseesessecseesssseesecsecsesseassassansancassarsaneaneaseaveseeass 3 REGULATORY NOTICES crier Eee etr eor eee e inert eee eee 3 DESCRIPTION INSTALLATION r Front Panel Controls OPERATION M 8 How To Adjust The entes Herten 8 VIGO 9 PE Modaram 10 MAINTENANCE SPECIFICATION 11 WARRANTY AND RETURN INFORMATION eese nennen 12 List of Illustrations Figure Page 1 PMCLISA Rear VIEW cio n cse etude 4 2 Looping Operation One monitor with External Video Equipment iun 3 Looping Operation Maximum of Three Monitors With external Video Equipment au 4 PMCLISA Front Panel Controls nasienia teeth dei eee 7 List of Tables Table Page A Video Coaxial Cable Requirements sse tentent tentent N 5 2 Pelco Manual C1965M C 12 03 IMPORTANT SAFEGUARDS AND WARNINGS
4. h French German Spanish or Italian Default setting is English Turn the camera title on or off select YES or NO Edit the camera title Select a camera and then press the Menu button to enter title editing submenu A title can be sixteen charac ters long Press the lt gt buttons to select a character location and press the AW buttons to change the character Press the Menu button to return to the submenu Reset all values to factory preset values Select to exit OSD menu Pelco Manual 1965 12 03 9 contrast it BRIGHTNESS D H POSITION O V POSITION plija PHASE CLOCK COLOR 8 ug TS Gs AUTO ADJUST VOLUME OSD H POSITION OSD V POSITION LANGUAGE COLOR TEMP RECALL MODE DATA exit EXIT 10 Pelco Manual C1965M C 12 03 Proper adjustment will allow maximum gradations between the darkest and lightest picture contrast Press the button to increase contrast and the lt button to decrease contrast Default setting is 85 Press the button to increase brightness and lt button to decrease brightness Default setting is 80 Adjust the horizontal position of the image on the screen Adjust the vertical position of the image on the screen Adjust the phase Press the lt gt buttons to set the clock Press the lt gt buttons to select a color Press the A V buttons to adjust the value of the selected color Automat
5. hen press the Menu button Pelco Manual C1965M C 12 03 Video Mode it BRIGHTNESS CONTRAST RGB COLOR SHARPNESS BS SEQUENCE TIME IB OSD H POSITION 1 amp ospvposition VOLUME LANGUAGE E TITLE ENABLE TITLE EDITING 43 RECALL EXIT EXIT Press the button to increase brightness and the lt button to decrease brightness Default setting is 8096 Proper adjustment will allow maximum gradations between the darkest and lightest picture contrast Press the button to increase contrast and the lt button to decrease contrast Default setting is 7090 Press the button to increase saturation level and the lt button to decrease color saturation level Default setting is 6296 Press the button to increase greenish tones in the picture Press the lt button to increase the reddish tones in the picture Default setting is 5096 Adjust the controls to obtain the clearest picture Default setting is 2 Set the sequencing time between channels Press the p button to increase the time Maximum setting is 24 second interval Press the lt button to decrease the time Minimum setting is 1 second inter val Default setting is 3 second interval Adjust the horizontal location of the OSD Adjust the vertical location of the OSD Press the button to increase volume and the lt button to decrease volume level Default setting is 50 Select the OSD language Englis
6. ically adjusts the H position V position phase and clock values Default position is ON Press the lt gt buttons for the desired audio level Adjust the horizontal location of the OSD Adjust the vertical location of the OSD Select the OSD language English French German Spanish or Italian Default setting is English Set the color temperature of the LCD monitor for the CIE coordinate 9300 k or 6500 k Recall the H position V position phase and clock values of the mode data Select to exit OSD menu MAINTENANCE If the quality of the picture is poor and cannot be improved by making adjustments on the front control panel inspect all system connections and cable runs To reduce the risk of electrical shock do not remove the cover or back of monitor No user serviceable parts are inside Refer servicing to qualified personnel or contact the Pelco Technical Support Depart ment for assistance Refer to the Warranty and Return Information section SPECIFICATIONS ELECTRICAL Input Voltage 100 240 VAC 50 60 Hz automatic switching Power Consumption Normal 35 watts maximum Standby 5 watts maximum Horizontal Resolution Visual Picture Size Sweep Linearity Speaker Output Connectors Video Input Output S VHS Input PC Input Audio Input Output AC Power Cord GENERAL Environment Construction Finish LCD Panel Type Colors Viewable Size Contrast Ratio Brightness Resolution Dimensio
7. matrix and DF5 DF8 Series fixed dome products Two years on Spectra Esprit ExSite and PS20 scanners including when used in continuous motion applications years on Esprit and WW5700 Series window wiper excluding wiper blades e Eighteen months on DX Series digital video recorders NVR300 Series network video recorders and Endura Series distributed network based video products year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months e Six months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight repaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s iability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages incl
8. ns LCD Panel Only LCD Panel with Base Unit Weight Shipping Weight ENVIRONMENTAL Operating Temperature Humidity 540 TV lines 15 inch diagonal 10 1 0 watt 3 dBV BNC 4 pin mini DIN 15 pin connector RCA 2 1 USA standard and 1 European standard Indoor Black plastic Black matte texture coat finish 15 inch 38 1 cm TFT color 16 7M colors 12 H x 9 V inches 30 48 x 22 86 cm 300 1 200 cd m 1024 x 768 pixels 12 0 Hx 154 Wx 2 78 D 80 48 x 39 05 x 7 11 cm 15 6 Hx 15 4 Wx 7 2 D 39 5 x 39 1 x 18 3 cm 11 2 lb 5 kg 16 Ib 7 26 kg 50 to 104 F 10 to 40 C 20 to 85 non condensing Design and product specifications subject to change without notice Pelco Manual 1965 12 03 11 PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below Five years on FT FR8000 Series fiber optic products Three years on Genex Series products multiplexers server and keyboard Three years on Camclosure and fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H 2X camera models which have a five year warranty Two years on standard motorized or fixed focal length lenses Two years on Legacy CM6700 CM6800 CM9700 Series
9. o Manual C1965M C 12 03 Front Panel Controls Refer to Figure 4 CHANNEL BUTTON Channel Select Press the Channel button once to display a camera view Auto Scan Press and hold the button for three seconds to sequence through composite video channels MENU BUTTON On screen display menu OSD BUTTONS Use to navigate through the OSD menus POWER LED Green Power ON Dark Power OFF Yellow Power saving mode POWER BUTTON Press the power button to turn the monitor ON OFF Figure 4 PMCL15A Front Panel Controls Pelco Manual 1965 12 03 7 1 2 3 4 Turn the monitor s main power switch ON The power switch is located on the base of the monitor refer to Figure 1 Push IN the power button located on the front of the monitor refer to Figure 4 The LED turns green Push the Channel button to select the input signal If required adjust the video using the front panel controls and the on screen display OSD How To Adjust The Video Use the front control panel to adjust the screen display 1 2 8 Press the Menu button to access the OSD Press the AW lt P buttons to move to an icon in the main menu Press the Menu button to select the icon submenu Press lt gt buttons to adjust the value in the submenu Press the Menu button to return to the main menu To exit the main menu press the lt gt to move to the EXIT icon and t
10. requirements Available inputs include the following BNC Connect the video cable to the BNC input labeled VIDEO IN 10n the back of the monitor If the installation requires a second video input connect a video cable to the BNC input labeled VIDEO IN 2 Looping Operation Only Connect a video cable to the BNC connector labeled VIDEO OUT 1 If the installation requires a second video output connect a video cable to the BNC output labeled VIDEO OUT 2 Refer to Figures 2 and 3 S VIDEO Connect the video cable to the input labeled S VHS IN PC BASED Connect the PC signal cable to the input labeled PC VIDEO IN 3 Plug the monitor power cord provided into the AC INLET connection on the back of the base Plug the other end of the cord into a power receptacle MAIN POWER SWITCH Figure 1 PMCL15A Rear View 4 Pelco Manual C1965M C 12 03 Table A Video Coaxial Cable Requirements Cable Type Maximum Distance RG59 U 750 ft 229 m RG6 U 1 000 ft 305 m RG11 U 1 500 ft 457 m Minimum cable requirements 75 ohms impedance All copper center conductor All copper braided shield with 95 braid coverage Figure 2 Looping Operation One Monitor with External Video Equipment Pelco Manual 1965 12 03 5 Figure 3 Looping Operation Maximum of Three Monitors With External Video Equipment 6 Pelc
11. rgy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try and correct the interfer ence by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Pelco Manual 1965 12 03 3 DESCRIPTION The PMCL15A is a high resolution 15 inch thin film transistor TFT LCD color monitor The unit produces a sharp picture with a resolution of 540 TV lines The monitor features multiple video inputs for S video and PC based imaging and supports circuitry for NTSC PAL formats with input voltages of 100 240 VAC INSTALLATION 1 The monitor can be placed on any flat surface desk or table 2 Refer to Figure 1 and connect the video signal to the monitor Refer to Table A for video coaxial cable
12. uding loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise he above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state f a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and rovide the following information 1 Model and serial number 2 Date of shipment P O number Sales Order number or Pelco invoice number 3 Details of the defect or problem f there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental
Download Pdf Manuals
Related Search