Paxar 9474 Printer User Manual
Contents
1. Equipment _ Monarch Manua TC9414PHX Rev AG 4 05 1999 Paxar Americas Inc All rights reserved Each product and program carries a respective written warranty the only warranty on which the customer can rely Paxar reserves the right to make changes in the product the programs and their availability at any time and without notice Although Paxar has made every effort to provide complete and accurate information in this manual Paxar shall not be liable for any omissions or inaccuracies Any update will be incorporated in a later edition of this manual 1999 Paxar Americas Inc All rights reserved No part of this publication may be reproduced transmitted stored in a retrieval system or translated into any language in any form by any means without the prior written permission of Paxar Americas Inc WARNING This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user2. ae Gee eae 2 4 Loading WAG Sa 2 5 Loading Labels for MRD and Dough Staging 2 5 Loading Labels for Hot Hold Items 2 9 Using the Keypad Terminal Buttons 2 11 Reading the Scan Sheet ceccnte 2 12 Processing the Product 2 13 Hot Hold Labeling 2 14 Inventory Labeling css 2 14 From Frozen to 2 16 Future DownloadS ii awa 2 17 Table of Contents i CARE AND 1 3 1 Clearing Label Jam 3 1 Cleaning the Printhead aa asad 3 2 Checking the Software Version eccere 3 2 Clearing 3 3 5 1 Table of Contents ii GETTING STARTED The MRD Made Ready Discard system is product freshness and inventory control labeling system that helps decrease product waste The system uses the Monarch 9414 printer with the keypad terminal and the Pizza Hut Application This chapter includes information about e unpacking the MRD system for new systems only setting up the MRD system reading the indicator light Unpacking the MRD System For new systems only After you unpack the MRD system you should have 9414 Prin
3. Scan the barcode from the Stage 2 label TEMPERED when the dough is ready for the next process 2 16 Using the Pizza Hut Application PRODUCT DOUGH PROCESS FROZEN UNOPENED RECEIVED ON 2 07 PM 1 23 03 Stage 1 Label PRODUCT DOUGH PROCESS TEMPERED MUST USE AFTER min Stage 2 Label Scan a quantity barcode from the scan sheet The Stage 3 label PROCESS RETARD prints with the new date time information Apply the Stage 3 label on top of the Stage 2 label Scan the barcode from the Stage 3 label PROCESS RETARD when the dough is ready for the next process Scan a quantity barcode from the scan sheet The Stage 4 label PRE TOP prints with the new date time information The PRE TOP label indicates the dough is ready to be topped If any errors occur when printing see Appendix A Troubleshooting for more information PRODUCT DOUGH PROCESS RETARD MUST USE AFTER 3 08 PM DISCARD BY END OF DAY 1 24 03 Stage 3 Label PRODUCT DOUGH PROCESS PRE TOP MUST USE BEFORE 6 08 PM IBIN Stage 4 Label Future Downloads Updates will be released by Pizza Hut Using the Pizza Hut Application 2 17 2 18 Using the Pizza Hut Application CARE AND MAINTENANCE EJ This chapter tells you how to clear label jams clean the printhead e check the software version e clear the buffer Clearing Label Jams When you are printing
4. Facing the front of the tray lay the serial cable part number 125802 behind the tray To keypad terminal To printer 5 Plug the three hole end of the printer s power supply cable into the three pronged outlet in the printer s power supply Power cable to Printer s Power Power cable to printer Supply wall outlet 6 Place the printer s power supply behind the tray with the printer s connector on the right side Getting Started 1 3 7 Place the keypad terminal s power supply into the tray under the shelf with the three pronged end facing the cut out in the back of the tray 8 Through the back of the tray plug the three hole end of the keypad terminal s cable into the three pronged outlet in the keypad terminal s power supply 18 24V Keypad Terminal s Power Supply Keypad Terminais power cable with L shaped connector 9 Lay the keypad terminal s cable with the L shaped connector on the shelf 10 Place the keypad terminal on the shelf but do not remove the tape from the Velcro at this point WARNING The printer s power supply uses different voltage than the keypad To connect the wrong power supply could permanently damage the keypad or the printer Straight Plug Plug is the power supply is the power supply for the printer for the keypad 1 4 Getting Started 11 12 13 The keypad terminal should not be operated in a location that has room temperat
5. go directly to a Stage 3 label scan Maketable from the process box on the top of the scan sheet and then scan the product 3 Go to Stage 3 Stage 3 1 When the product is ready for the next process Stage 3 scan the barcode from the Stage 2 label or scan Maketable from the process box on the top of the scan sheet and then scan the product The process is done all stages complete when a label prints without a barcode Scan a quantity barcode from the scan sheet The Stage 3 label prints with the new date and time information Apply the Stage 3 label on top of the Stage 2 label PIZZA CHEESE RECEIVED ON 12 56 PM 1 22 03 READY 12 56 PM 1 25 03 DISCARD 12 56 PM 2 01 03 Stage 2 Label PRODUCT PIZZA CHEESE ON MAKETABLE 12 56 PM 1 22 03 DISCARD 12 56 PM 1 23 03 Stage 3 Label Using the Pizza Hut Application 2 15 From Frozen to Pre Top This section explains how to take frozen dough to the pre top stage 1 When you receive frozen dough press the Dough Frozen Pan BDSTK Retard button on the keypad terminal The Stage 1 label prints with date and time information Apply the Stage 1 label to the product Scan the barcode from the Stage 1 label when the dough is ready for the next process Scan a quantity barcode from the scan sheet The Stage 2 label TEMPERED prints with new date time information Apply the Stage 2 label on top of the Stage 1 label
6. E NTIN 01 04 07 UT A IN 02 0 08 5 TN I I 03 06 09 The PRODUCT sections from the scan sheet are shown on the following page The scan sheet can be found posted near the MRD system 2 12 Using the Pizza Hut Application Processing the Product Use the Pizza Hut application to label the Hot Hold items and inventory products You can find the products either on the product quantity scan sheet or on the keypad terminal NOTE One side of the scan sheet is in English the other side is in Spanish PIZZA Scan to get a RECEIVED ON Label Bacon Pieces Buffalo Chicken Jala Penos Black Olives Meat Mix izza Cheese Italian Sausage OT ese apple Tomatoes Green Peppers Pre Cut Mush rooms Red Onions Pre Cut Pepperoni Pizza Sauce Concentrate WINGS Scan to get a RECEIVED ON Label SUBS Scan to get a RECEIVED ON Label Sandwich Meats Sandwich Cheese Sliced Dressings Tomatoes Lettuce precut Pre Set Subs BREAKFAST BAKED CINNAMON STICKS Scan to get a RECEIVED ON Label American Cheese Cinnamon Sugar BREADSTICKS Dough Bacon Strips Sausage Patty Scrambled Egg Square Hash Brown Rounds Baked Cinnamon Sticks Icing Dipping cups Scan to get a RECEIVED ON Label Butter oil Breadstick Sauce Using the
7. Paxar will not accept the printer for service under warranty Products received in unsuitable containers will be returned in Paxar approved packaging at the customer s expense Thermal Printhead Warranty The thermal printhead is covered by a prorated limited warranty of six 6 months or one million 1 000 000 inches of use whichever occurs first Physical damage to the printhead is not covered by the limited warranty Battery and Cable Warranty Batteries and cables are covered by a prorated limited warranty of three 3 months from the date of shipment Physical damage to the battery ies or cable s is are not covered by the limited warranty Troubleshooting A 3 Consumables The product limited warranty does not include or cover consumables or sundry items such as ribbons tags labels knives batteries cables or thermal printheads see above battery cable and thermal printhead warranty Use of Supplies Only genuine Paxar or Monarch supplies are recommended for use in Paxar products This limited warranty does not cover service required as a result of the use of non Paxar supplies Host Communication Service required to develop or correct on line host communications including the use of non Paxar communications cables is not covered by the product warranty Operating Instructions Proper operation of the product requires the user to read and follow the operating instructions The limited warranty does not co
8. a GROUNDED electrical outlet ALWAYS PLUG THE PRINTER INTO THE ELECTRICAL WALL OUTLET FIRST AND THEN TURN ON THE PRINTER Plug the keypad terminal s power cable into a GROUNDED electrical outlet WARNING The printer and power supply should never be operated in a location where either one can get wet Personal injury could result Press the power switch on the back of the printer to the ON position 1 to turn on the printer Getting Started 1 7 Reading the Indicator Light The indicator light monitors the printer s status Indicator Light around the Feed Button Feed Button Indicator Light Description GREEN Printer is on and ready to use RED Supply has run out or is not loaded Load supply See Chapter 2 Using the Pizza Hut Application for more information Or clear the buffer Follow the steps below ORANGE Error has occurred See Appendix A Troubleshooting for more information To clear the error press the FEED button Or clear the buffer Follow the steps below No light Printer is off Make sure the power supply is connected properly See Setting up the System earlier in this chapter 1 8 Getting Started Clearing the Buffer To clear the buffer 1 Turn off the printer 2 Load labels for non peel mode See Chapter 2 Using the Pizza Hut Application 3 Press and hold the FEED button while turning on the printer 4 Release the FEED button when the indi
9. and a jam occurs the indicator light turns ORANGE To clear the jam 1 MAKE SURE THE POWER IS OFF Press to turn off and 1 to turn on 2 Press the cover release buttons on both sides of the printer towards the front of the printer Lift open the cover 3 If necessary remove any supply that has been previously loaded by pushing out the supply holder tabs The supply should lift out of the printer 4 Remove the jammed labels Do not use sharp or pointed objects to remove labels or damage to the printhead may occur 5 Reload the supply Chapter 2 Using the Pizza Hut Application for more information Close the cover until the cover locks in place 7 Press the FEED button to clear the error The indicator light should turn GREEN Care and Maintenance 3 1 Cleaning the Printhead Clean the printhead every time you load a new label roll into the printer 1 MAKE SURE THE POWER IS OFF Press to turn off and 1 to turn on 2 Press the cover release buttons on both sides of the printer towards the front of the printer Lift open the cover 3 Gently rub the cleaning pen across the printhead 4 Allow the printhead to dry for one minute before closing the cover and resume printing Checking the Software Version Your keypad terminal displays the software version when it is turned off and then turned back on 3 2 Care and Maintenance Clearing the Buffer To clear the buffer 1
10. 2 MAKE SURE THE POWER IS OFF Load labels for non peel mode See Chapter 2 Using the Pizza Hut Application Press and hold the FEED button while turning on the printer Release the FEED button when the indicator light starts flashing red Several labels advance including the status label Press the FEED button Care and Maintenance 3 3 3 4 Care and Maintenance TROUBLESHOOTING ry Problem Action Indicator light is off Check the power connections from when the printer is the power supply to printer AC turned on outlet See Setting Up the System in Chapter 1 Indicator light is Check the interface cable GREEN but the connections from the computer to printer will not printer See Setting Up the System print in Chapter 1 Verify that the labels are the correct type thermal direct not thermal transfer and supply is loaded correctly See Chapter 2 Using the Pizza Hut Application Clean the printhead See Cleaning the Printhead in Chapter 3 Make sure the cover is closed Printing is faded or Verify that the labels are the correct poor quality type thermal direct not thermal transfer and supply is loaded correctly See Chapter 2 Using the Pizza Hut Application Clean the printhead with a cleaning pen See Cleaning the Printhead in Chapter 3 Adjust the print speed darkness See your System Administrator Label exits partially A label might be caugh
11. Mild Wings button Do not press Shift and a product button at the same time Press and release the Shift button then press a product button Print Quantity use the numeric buttons to enter quantity of labels that you want printed The numeric buttons should be pressed first before pressing a product button Hot Hold Items Other Products Dough Items gt Numeric Language Shift Button Button Using the Pizza Hut Application 2 11 Reading the Scan Sheet The scan sheet helps you quickly process your inventory by scanning the barcodes at various stages of food preparation There are three stages Stage 1 Creates a received on label Stage 2 Creates a thaw stage label Not all products require a thaw label For example black olives go from a received on label directly to the maketable Stage 3 Creates a maketable stage label You can by pass Stage 1 or Stage 2 labels x lt when you take a product directly from the distributor into the thaw stage or preparation stage maketable To by pass Stage 1 labels scan Thaw from the process box at the top of the scan sheet To by pass Stage 2 labels scan Maketable from the process box at the top of the scan sheet See Inventory Labeling for more information Below is the PROCESS box from the scan sheet PROCESS Only scan if you want to by pass a RECEIVED ON Label Below is the QUANTITY box from the scan sheet QUANTITY TO PRINT I
12. Pizza Hut Application 2 13 Hot Hold Labeling Wa 0 To print one label press a product button on the keypad terminal one time apd To print several Hot Hold Labels ASK FOR A FRESH PRODUCT AFTER 1 Press the numeric buttons to enter 1 03 PH a quantity The display prompts you for a per product BREADST I CKS Hot Hold Sample 2 Press a product button Inventory Labeling The inventory management process starts when the Stage 1 label prints with the date time information and is applied either to a product label or is applied somewhere on the product bag or box 1 Scan a product barcode from the scan sheet to print a Stage 1 label PIZZA CHEESE 2 Scan quantity barcode from the RECEIVED ON scan sheet The Stage 1 label 12 56 PM prints Stage 1 1 22 03 Sai SN To by pass a Stage 1 label and go directly to a Stage 2 label scan Thaw from the process box on the top of the scan sheet and then scan the product Stage 1 Label 3 Go to Stage 2 2 14 Using the Pizza Hut Application Stage 2 1 When the product is ready for the next process Stage 2 scan the barcode from the Stage 1 label or scan Thaw from the process box on the top of the scan sheet and then scan the product Scan a quantity barcode from the scan sheet The Stage 2 label prints with the new date time information Apply the Stage 2 label on top of the Stage 1 label xa To by pass a Stage 2 label and g
13. cator light starts flashing red Several labels advance including the status label 5 Press the FEED button Switching Print Modes To switch the printer to print labels for Hot Hold Items 1 Open the peel bar cover by pushing down 2 Change print modes to peel by switching the print mode switch to the 1 position 1 Peel Mode O Non peel Mode Print Mode Switch 3 Load supplies for Hot Hold Items See Chapter 2 Using the Pizza Hut Application for more information Getting Started 1 9 1 10 Getting Started USING THE PIZZA HUT APPLICATION This chapter describes how to set the date time hot hold time select a language load labels process the product Using the Pizza Hut Application 2 1 Setting the Date Time Hot Hold Time Keep this manual in a safe place otherwise changing the settings would require a service call To set the Date 1 Scan this barcode to start the program 2 The display shows the current date setting If this is correct press the Pizza Hut button To change the setting use the top row buttons on the keypad terminal Cheese button changes the month Supreme button changes the day Pepperoni button adds a year Meat Lover s button subtracts a year 3 Press the Pizza Hut button to exit 2 2 Using the Pizza Hut Application To set the Time 1 3 Scan this barcode to start the program The display shows the
14. current time setting If this is correct press the Pizza Hut button To change the setting use the top row buttons on the keypad terminal Cheese button changes the hours Supreme button changes the minutes Pepperoni button changes AM PM Press the Pizza Hut button to exit To set the Humidified Hot Hold Time 1 Scan this barcode to set the Humidified Hot Hold Time The display shows Set to Winston Bevilis or Henny Penny Hot Hold The time will be set depending on the product Using the Pizza Hut Application 2 3 To set the Dry Hot Hold Time 1 Scan this barcode to set the Dry Hot Hold time The display shows Set to Dry Hot Hold i e Hatco JR2000 The time will be set depending on the product Selecting a Language The language selection is only for hot hold freshness labels If Spanish is selected pressing a dough button prints a dough label in Spanish The keypad terminal display is always in English To select a language 1 Press the English Spanish button once The current language setting displays 2 Continue pressing the English Spanish button until you see the option you need English e Spanish English Spanish 3 Press the Pizza Hut button to save the setting 2 4 Using the Pizza Hut Application Loading Labels If run out of labels while printing do not turn off the printer when reloading the labels You may lose your data The printer resumes
15. he supply holder tabs Load the supply roll Press the supply under the supply guides and adjust the supply guides so they just touch the edges of the backing paper Open the peel bar cover by pushing down KX peel Bar Cover Print Mode Switch 77 Change print modes to peel by switching the print mode switch to the 1 position 1 Peel Mode O Non peel Mode Remove the first two labels from the backing paper Using the Pizza Hut Application 2 9 10 Feed the backing paper over the peel bar and under the peel roller 11 Press the supply under the supply guides and adjust the supply guides so they just touch the edges of the backing paper 12 Close the peel bar cover by pushing up until it locks 13 Close the cover until the cover locks in place 14 Press the FEED button The indicator light should be GREEN 2 10 Using the Pizza Hut Application Using the Keypad Terminal Buttons Hot Hold Items Red buttons Personal Pan Pizza Primo Breadsticks Wings and Breakfast items prints a label with the product name and the freshness time Dough Products prints labels with the time date for each preparation process For more information about dough products see From Frozen to Pre Top Shift Press Shift to get products listed at the top of certain buttons For Mild Wings press the Hot Wings Mild Wings button For Hot Wings press and release Shift then press the Hot Wings
16. nical support center 2 A Paxar technical support specialist will work with you to attempt to resolve the problem by telephone 3 If telephone resolution of your problem is unsuccessful the technical specialist will issue an incident for you to return your product prepaid for warranty repair subject to the terms of the limited warranty above Troubleshooting A 5 A 6 Troubleshooting For missing items parts a cleaning pen service or technical assistance call toll free 1 888 MON 9414 For more paper labels call one of the following PrimeSource 1 800 397 4737 item 85221 Wasserstrom 1 800 999 9277 item 374014 Unified Food Co op 1 800 444 4144 item 374014
17. printing when reloaded Loading Labels for MRD and Dough Staging 1 2 Remove and discard the tape from a new roll of labels Press the cover release levers on both sides of the printer towards the front of the printer to release the cover Lift open the cover Remember to clean the printhead every time you load a new label roll into the printer Turn the printer OFF to clean it See Cleaning the Printhead in Chapter 3 for more information Using the Pizza Hut Application 2 5 3 Adjust the supply guides to their widest position by turning the dial 4 Open the supply holders to their widest position by pushing out the supply holder tabs 2 6 Using the Pizza Hut Application 5 6 Load the supply roll ius Press the supply under the supply guides and adjust the supply guides so they just touch the edges of the backing paper ee Using the Pizza Hut Application 2 7 7 Close the cover until the cover locks in place 8 Press the FEED button The indicator light should be GREEN 2 8 Using the Pizza Hut Application Loading Labels for Hot Hold Items 1 2 Remove and discard the tape from a new roll of labels Press the cover release buttons on both sides of the printer towards the front of the printer Lift open the cover Adjust the supply guides to their widest position by turning the dial Open the supply holders to their widest position by pushing out t
18. t in the out of the printer or printer See Clearing Label Jams skips a label in Chapter 3 Load the supply correctly See Chapter 2 Using the Pizza Hut Application Check printer s memory configuration See your System Administrator Troubleshooting A 1 Problem Printing stops and indicator light turns ORANGE Action Adjust the label gap sensor 1 Turn off the printer 2 Load labels for non peel mode See Chapter 2 Using the Pizza Hut Application 3 Press and hold the FEED button while turning the printer on 4 Release the FEED button when the indicator light starts flashing red Several labels advance including the status label 5 Press the FEED button Problem with the supply Load different supply See Chapter 2 Using the Pizza Hut Application Clear label jam See Clearing Label Jams in Chapter 3 Software problem Check the printer memory configuration See your System Administrator The printer does not detect the gap between each label Adjust the label gap sensor 1 Turn off the printer 2 Load labels for non peel mode See Chapter 2 Using the Pizza Hut Application 3 Press and hold the FEED button while turning on the printer 4 Release the FEED button when the printer starts advancing lines Several labels advance including two Diagnostic labels 5 Press the FEED button The keypad terminal displays an error A 2 Troubleshoo
19. ter and power supply keypad terminal with rubber cover may already be on the keypad terminal and power supply e scanner communications cable Equipment Manual Keep this manual in a safe place Maintenance Quick Reference Sheet Job Aid and System Setup Sheet product quantity scan sheet Velcro strips four extra cable ties four bolts two and wood screws two Tray If you need help please call 1 888 666 9414 If you need more paper labels call one of the following Prime Source 800 397 4737 order item 85221 Wasserstrom 800 999 9277 order item 374014 Unified Food Co Op 800 444 4144 order item 374014 Getting Started 1 1 Keep all packaging material in case you need to move or return the MRD system Setting Up the System CAUTION Do not touch the electrical connectors while setting up the printer Electrostatic discharge can damage or destroy the printhead or electronic components 1 Remove the tray from its packaging Check inside the packaging for the adhesive feet Remove the feet from their adhesive backing and apply one to each corner 2 Place the tray on the cut table near an electrical outlet Adhesive Feet nes gt Tray design may vary from the one shown in this manual 3 Make sure the power on the printer is turned off before setting up any cables The power switch on the back of the printer should be in the OFF O position 1 2 Getting Started 4
20. ting Clear the error turn off the printer and then back on Paxar Barcode Product Limited Warranty Thank you for purchasing a Paxar or Monarch brand barcode product Paxar warrants that your product will be free from defects in material and workmanship for a period of one 1 year from the date of shipment by Paxar Please read this warranty very carefully THIS WARRANTY IS A LIMITED WARRANTY AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES EITHER EXPRESS OR IMPLIED INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Warranty Period The limited warranty starts on the day the product is shipped from Paxar and ends after a period of one 1 year or when the product s life has been exceeded whichever occurs first Parts and Labor Paxar will provide new or remanufactured parts and labor free of charge to correct defects in material and workmanship for the product s covered by the limited warranty during the warranty period This limited warranty is a depot warranty only Shipping The customer is responsible for inbound transportation charges and Paxar is responsible for return transportation charges via ground to correct defects in material and workmanship during the limited warranty period Packaging Products returned shall be packaged in the original packaging and shipping container or comparable container In the event the product is not packaged properly or if shipping damage is evident
21. ures above 158 F or below 4 F for extended periods of time This could permanently damage the display Plug the L shaped connector into the socket located on the top of the keypad terminal 12V Connect the serial cable to the top of the keypad terminal wz d P 1 Lt L shaped i ao Connector Serial Cable F i Place the printer in the tray The printer should never be operated while resting on its side or upside down ALWAYS PLUG THE PRINTER INTO THE ELECTRICAL WALL OUTLET FIRST AND THEN TURN ON THE PRINTER NEVER TURN ON THE PRINTER AND THEN PLUG IT INTO THE WALL OUTLET Getting Started 1 5 14 Plug the printer s power supply cable with the straight end into the socket on the back of the printer Power Cable Serial Cable 15 Connect the serial cable to the printer s serial port 16 f necessary adjust the cables Make sure all the cables move freely through the openings in the back of the tray Use a cable tie to secure them 17 Lift up the keypad terminal with one hand and feed the scanner cable connector through the notch as shown Scanner Cable 7 8 1 6 Getting Started 18 19 20 21 22 Plug the scanner cable connector into the socket and then turn the connector to lock the cable in place Remove the tape from the Velcro on the keypad terminal and put the keypad terminal onto the shelf Plug the printer s power supply cable into
22. ver service that is required as a result of operator error and or failure to read and follow the documentation included with the product Installation and Training Installation and training of the operators is a professional service that is available on a time and material basis Installation and training is not covered by the limited warranty Exclusions This limited warranty covers defects in material and workmanship only and does not cover damage to batteries and cables or caused by accident abuse violence acts of God or use of non Paxar or non Monarch supplies or those not meeting the Paxar specifications Paxar shall not be liable for direct indirect or consequential damages costs expenses lost profits or lost savings resulting from the use operation or malfunction of the verifier This limited warranty is valid only in the United States of America This limited warranty is the only warranty on which the customer can rely Paxar reserves the right to make changes in the products programs and their availability at any time and without notice This warranty is void if the product is altered or repaired by anyone except a Paxar service representative or contrary to the instructions provided by Paxar A 4 Troubleshooting To Initiate a Warranty Claim The customer must follow the steps below in order to make a warranty claim under the limited warranty 1 Call 800 543 6650 in order to report your problem to our tech
23. will be required to correct the interference at his own expense CANADIAN D O C WARNING This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la classe A prescrites dans le R glement sur le brouillage radio lectrique dicte par le minist re des Communications du Canada Trademarks 9414 and Monarch are trademarks of Paxar Americas Inc Paxar is a trademark of Paxar Corporation Pizza Hut is a registered trademark of Pizza Hut Inc Personal Pan Meat Lover s Panwich and Supreme are registered trademarks of Pizza Hut Inc Velcro is a registered trademark of Velcro Companies Paxar Americas Inc 170 Monarch Lane Miamisburg OH 35342 TABLE OF CONTENTS GETTING STARTED 1 1 Unpacking the MRD 1 1 Setting 1 2 Reading the Indicator 1 8 Clearing the 1 9 Switching Print 1 9 USING THE PIZZA HUT 2 1 Setting the Date Time Hot Hold 2 2 Selecting a Language
Download Pdf Manuals
Related Search