Outlaw Audio 7500 Stereo Amplifier User Manual
Contents
1. To determine if a cable TV connection is responsible for the hum first turn all components off Disconnect the cable TV feed to your system at the first place where it connects to your components Alternatively disconnect the cable TV wire where it is connected at the wall outlet Turn your system back on and listen if the hum has disappeared If removing the cable TV feed has eliminated the hum you will need to insert a Ground Loop Isolator before reconnecting the cable TV feed or contact your cable TV operator to see if they can better isolate your cable feed Suggestion 2 Turn off all components in your system and then disconnect the input cables at the amplifier Turn the amplifier back on and see if the hum is still present If the hum disappears the fault may be in the input cables used Try replacing them with cables that have better shielding and make certain that the input cables are not running on top of any AC power cords Change the cables one at a time to determine if one or all cables is responsive If the hum disappears when the input cables are disconnected but returns after the cables are changed and the system re connected the problem may be caused by your processor receiver or preamplifier Suggestion 3 Ground loop problems may also be caused by poor grounding of the electrical system in your home particularly when there are multiple components with three prong grounded power cords Try unplugging these comp2. at the impedance rating of your speakers Outlaw Audio is not responsible for damage to any speaker system or other component that is caused by using products whose power rating is lower than that of the amplifier Do Not Open The Cabinet There are no user serviceable components inside this product Opening the cabinet may present a shock hazard and any modification to the product will void your guarantee If water or any metal object such as a paper clip coin or a staple accidentally falls inside the unit disconnect it from the AC power source immediately and contact Outlaw Audio for further instructions IMPORTANT SAFETY NOTE Before connecting a new component such as power amplifier to your audio or home theater system it is always good practice to make certain that all components are turned off and preferably unplugged from their AC power source Many modern electronics products feature automatic turn on circuits that may be activated during an installation causing the potential for damage to electronic components and or speakers Such damage is not covered by product warranties and Outlaw Audio specifically disclaims responsibility for any such damage Es Outlaw Audio For Future Reference Record your amplifier s serial number and date of purchase here It is found on the back panel Model Number Serial Number Date of Purchase Table of Contents Please Read First Table of Contents Feature
3. that for your grounding connection Suggestion 5 If you have hum in your video display device bars that roll up through image at 12 14 second intervals this may be related to hum you also experience in your audio system The previous suggestion tips may help with this also If not try isolating the ground in the projectors video signal cable with a base band video isolation transformer such as the Jensen VB 1BB If the hum persists after all of the above suggestions have been tried contact the Outlaw Audio customer service department for assistance 60Hz AC Ground Loop Main House Grounding El Outlaw Audio AC Line AC Line AC Ground Owner s Manual Specifications Specifications Model 7500 Model 7700 Power Output 5 x 200 watts 8 ohms FTC 20 20kHz 0 03 THD 7 x 200 watts 8 ohms FTC 20 20kHz 0 03 THD All Channels Driven 5 x 300 watts 4 ohms All Channels Driven 7 x 300 watts 4 ohms FTC 20 20kHz 0 03 THD All Channels Driven FTC 20 20kHz 0 03 THD All Channels Driven Frequency Response 20Hz 20kHz 0 1dB at rated output 20Hz 20kHz 0 1dB at rated output Total Harmonic Distortion THD Less than 0 03 at rated output all frequencies less than 0 005 at 1kHz Less than 0 03 at rated output all frequencies less than 0 005 at 1 kHz Intermodulation Distortion IMD Less than 0 03 from 250mV to full rated
4. You may wish to have someone help you remove the unit from its carton and place it in the proper location Model 7700 7500 Multi Channel Power Amplifier Esa Owner s Manual Rear Panel Rear Panel _ INP ITS UNBALANCED UNBALANCED UNBALANCED UNBALANCED O BALACED BALF ICED BALL ICED BALA ICED UNBALANCED UNBALANCED UNBALANCED Q son MASTER POWER BALA ICED BALA ICED BALANCED CIRCUIT BREAKER 15 AMP e OUTPUTS CON CTIONS SEE OWNER S MANUAL BEFORE USING NE PAS OUVRIR Note tems in gray shaded area are found on Model 7700 amplifier only AVIS RISQUE DE CHOC ELECTRIGN 120 VAC 60Hz 1800W A Unbalanced Audio Inputs E Use the Unbalanced INPUT jacks to connect the RCA outputs of a surround processor preamplifier AV receiver with RCA preout connections DVD player with discrete five channel outputs or HDTV product with built in surround decoder see page 5 B Balanced Unbalanced Toggle switch G Use the toggle switch to select Balanced or Unbalanced Input for each amplifier channel see page 5 C Remote Trigger Input Use the REMOTE TRIGGER jack to connect to a compatible processor or other product with a 3 32 VDC output see page 8 D Balanced Audio Inputs Use the Balanced INPUT jacks to connect the XLR balanced outputs of a surround processor preamplifier or AV rece
5. and it is important to ensure a proper connection between the interconnect cable and the input jack Connections with XLR Balanced audio type plugs When making connections with XLR type plugs on balanced interconnect cables make certain to gently but firmly insert them into the jacks marked balanced input on the back of the Model 7700 7500 Set the input toggle in the Balanced position before attempting to operate Loose connections can cause intermittent sound and may damage your speakers IMPORTANT NOTE When releasing an XLR connector from an input Jack press the plate style tab on the input jack male end of cable and pull the interconnect straight out When releasing an XLR con nector from an output jack press the button style tab on the XLR connector female end of cable and pull the interconnect straight out Unlike turbine style RCA cables twisting the interconnect will damage the cable and input jack on your amplifier Speaker Connections To assure that the high quality signals produced by your Outlaw amplifier are carried to your speakers without loss of clarity or resolution we recommend that you use high quality speaker wire Many brands of wire are available the choice may be influenced by the distance between your speakers and the amplifier the type of speakers you use personal preferences or other factors Regardless of the brand or type of speaker wire selected we recomm
6. of your Outlaw power amplifier may require heavy power draw under full load conditions To insure proper performance and to avoid potential safety hazards we recommend that it be connected to a minimum 20 Amp capacity circuit Connecting multiple amplifiers to the same circuit or connecting it to a circuit used by other heavy power devices such as air conditioners may cause circuit breakers to trip NOTE t is always a good idea to avoid using any audio or video equipment on the same AC circuit as equipment with motors such as air conditioners or refrigerators This will lessen the possibility of power variation and electrical start up noise affect ing your sound system Extension Cords and Power Strips We do not recommend that extension cords be used with this product unless they are of sufficient gauge to pass the necessary current during full load conditions Most inexpensive extension cords are not capable of such high current loads Similarly should you use a power strip surge protector or any type of AC power line con ditioning equipment make certain that it is also able to handle the high current loads this product will produce Handle the AC Power Cord Gently When disconnecting the power cord from an AC outlet always pull the plug never pull the cord If you do not intend to use the amplifier for any considerable length of time discon nect the plug from the AC outlet If the power cord is replaced make certain that it is
7. FTC power Less than 0 03 from 250mV to full rated FTC power Power Bandwidth 5Hz gt 100kHz 0 3dB 5Hz gt 100kHz 0 3dB Damping Factor Greater than 400 from 10Hz to 400Hz Greater than 400 from 10Hz to 400Hz Crosstalk Greater than 100dB from 20Hz to 20Khz Greater than 100dB from 20Hz to 20Khz Gain Voltage gain of 34dB XLR Voltage gain of 34dB XLR Voltage gain of 28dB RCA Voltage gain of 28dB RCA Slew Rate 50v Microsecond 50v Microsecond Input Impedance Nominal 28k ohms Nominal 28k ohms Input Sensitivity 1 43 Volts for Full Rated Output 1 43 Volts for Full Rated Output Remote Trigger Voltage 3 32 Volts DC at 5 milliamperes or greater 3 32 Volts DC at 5 milliamperes or greater Dimensions HxWxD 7 75 x 17 2 x 18 HxWxD 7 75 x 17 2 x 18 Weight 80 Ibs 93 Ibs Power Requirements 1I5VAC 3 50Hz 60Hz 1800 watts maximum 1I5VAC 3 50Hz 60Hz 1800 watts maximum Model 7700 7500 Multi Channel Power Amplifier I Owner s Manual Outlaw Audio Limited Warranty The Outlaw Audio 30 Day Satisfaction Guarantee This product is guaranteed to satisfy all your needs for a high performance power amplifier If for any reason you are not completely satisfied with it please contact us at 866 OUTLAWS 688 5297 within 30 days of receipt of the unit and you will receive a return authorization Please save all of your packing material since the ampli
8. Model 7700 7 Channel Power Amplifier Model 7500 5 Channel Power Amplifier Presa Owner s Manual Owner s Manual Please Read First Please Read First CAUTION AN RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION To reduce the risk of electric shock do not remove the cover or back No user serviceable parts inside Refer to qualified personnel WARNING To reduce the risk of fire or electric shock do not expose this appliance to rain or moisture The lightning flash with arrowhead within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous volt age within the product s enclosure that may be of sufficient magnitude to constitute a risk of electrical shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating maintenance servicing instructions in the literature accompanying the appliance Precautions Verify The Line Voltage Your new power amplifier has been factory configured for 120 3 volt AC lines Connecting the amplifier to a line voltage other than that for which it is intended can create a safety and fire hazard and may damage the amplifier If you have any questions about the voltage requirements for your specific model or about the line voltage in your area contact Outlaw Audio before plugging the unit into a wall outlet Verify AC Circuit Capacity The high power output
9. available to verify the purchase date should you experience a problem covered by our warranty A Few Words About Hum and Noise Audible hum or a discernable low frequency noise is one of the most com mon problems in audio video systems This hum which may be present even when the volume is at a low level or when the power is off is usually caused by a problem known as ground loops A ground loop occurs when there is a difference in ground voltages between two or more components that are con nected electrically This in turn creates multiple current paths and causes the low level noise or hum The growing sophistication of home theater systems and the increased number of components used to create these systems has dramatically increased the potential for the possibility of ground loops While it is natural to suspect that the components in your system are the cause of the hum in many cases the cause may be due to other conditions In particular cable TV connections from outside the house have become a major source of hum In most cases one of the following suggestions should help you to solve a hum problem in your system Please try these steps in the sequence shown proceeding from one step to the next if the prior suggestion does not eliminate the problem Model 7700 7500 Multi Channel Power Amplifier 9 Owner s Manual A Few Words About Hum and Noise Potential Ground Loops in a Complex A V System Suggestion 1
10. ble fire hazard If the unit is to be enclosed in a cabinet or rack make certain there is adequate air cir culation Sufficient ventilation should be provided so that hot air may exit and cool air may enter the cabinet In some instances a small cooling fan may be required to insure adequate airflow through the cabinet If you are in doubt as to the ventilation require ments for your specific installation please contact us Also do not place the amplifier directly on a carpeted surface as this will inhibit airflow underneath as well as create a potential fire hazard Avoid installation in humid locations in extremely hot or cold locations or in areas that are exposed to direct sunlight or space heating equipment Loudspeaker Ratings Your Outlaw power amplifier has adequate power to drive most loudspeakers without producing any distortion Most modern speakers are rated at four to eight ohms nominal impedance but within some frequency ranges the impedance may drop to two ohms The Outlaw is designed with ample power reserves to protect you from experiencing any problems at these low impeadances unless you demand excessively high volume levels Due to the high power output capability of your power amplifier it is important that it not be used with speakers not capable of handling the amplifier s power output Before using the amplifier for the first time make certain that your speakers are capable of handling its rated power output
11. e determined by the earliest date of manufacture shown on the unit provided that the serial number label has not been altered in any manner or by our records relating to that serial number In the event that you wish to return your Outlaw amplifier back to us for any reason please call to arrange for a Return Authorization Number This will insure that your problem is discussed with a service technician who will determine if there is a quick solution to your problem Outlaw Audio shall not be liable for in any way responsible for any inci dental or consequential damages of any kind Some states do not allow limitations on how long an implied warranty lasts and or do not allow the exclusion of incidental or consequential damages therefore the limita tions and exclusions stated herein may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state THERE ARE NO WARRANTIES GIVEN BY OUTLAW AUDIO WHICH EXTEND BEYOND THE DESCRIPTION GIVEN HEREIN ANY IMPLIED WARRANTIES OF FITNESS FOR PURPOSE SOLD MERCHANTIABILITY DESCRIPTION QUALITY OR ANY OTHER MATTERS ARE LIMITED TO THE TERMS OF THE EXPRESSED LIMITED WARRANTY STATED HEREIN Products are sold on the basis of specifications applicable at the time of sales Outlaw Audio shall have no obligation to modify products once they have been sold This warranty is applicable only in the United States For applicability in
12. e made by simply inserting the jack affixed to your speaker wire into the hole provided on the rear of the colored screw caps on the binding posts Before using banana type jacks make certain that the plastic screw caps are firmly tightened down by turning them in a clockwise direction until they are snug against the chassis This will insure that the maximum surface area of the plug is in contact with the jack Be certain to observe proper polarity Run the cables to the speaker locations It is recommended that the length of wire connecting any pair of speakers be similar For example make certain that the wire length connecting the left and right front or the left and right rear surround speakers are similar in length even though one speaker may be physically closer to the amplifier than the other Do not coil any excess cable as this may become an inductor that creates frequency response variations in your system Finally connect the wires to the speakers again being certain to observe proper polarity Remember to connect your negative or black wire to the matching terminal on the speaker The positive or red wire should be connected to the matching terminal on the speaker NOTE While most speaker manufacturers adhere to an industry conven tion of using red terminals for positive connections and black terminals for negative some manufacturers may vary from this configuration To assure proper phase connections and optimal performa
13. end that you use a wire constructed of fine multi strand copper with a gauge of 14 or less Remember that in specifying wire the lower the number the thicker the cable Wire with a gauge of 16 may be used for short runs of less than ten feet We do not recommend that you use any wires with an AWG equivalent of 18 or higher due to the power loss and degradation in performance that will occur To connect the amplifier to your speakers a pair of binding posts is provided for each channel output These posts will accept bare wire spade lugs or banana type plugs when they are permitted by local safety agencies If bare wire is used for the connections strip approximately 1 2 inch to 3 4 inch 20mm of insulation from the end of each wire and carefully twist the Owner s Manual Connecting Your Amplifier strands of each conductor together Be careful not to cut the individual strands or twist them off For optimal performance all strands must be used Correct polarity connections are important to maintain proper speaker phasing When speaker phasing is correct all speakers move in and out at the same time preserving the imaging of the program material Out of phase connections mean that some speaker cones will be moving in while others move out This will cause indistinct or confused imaging and muddled and cloudy sounds To avoid incorrect phasing or polarity be certain to use cable that has distinct markings colors stripes wording or g
14. fier is heavy and can get damaged in shipping without proper protection We recommend that you keep the packing even after 30 days so that if you ever move the unit will be adequately protected If you decide to return the amplifier the only cost you will be responsible for is the shipping charge to return it to us When your amplifier arrives we will inspect it to insure that it was shipped back to us in original condition Upon satisfactory inspection we will issue a full credit for your original purchase price plus your original outbound freight cost Outlaw Audio Limited Warranty This warranty protects the owner of the Outlaw 7500 7700 Power Amplifier the PRODUCT for five 5 years from the date of purchase This warranty covers all defects in material and workmanship with the following specific exceptions These are Damage caused by improper installation or adjustment Damage caused by accident unreasonable use or neglect Damage from failure to follow instructions contained in this Owner s Manual Damage from the performance of repairs by someone not authorized by Outlaw Audio Any unit on which the serial number has been effaced modified or removed Damage occurring during shipment Units which have been altered or modified in design appearance or construction This warranty covers only the actual defects within the PRODUCT itself IT DOES NOT cover costs of installation in or removal from a fixed installa
15. iver with XLR preout connections see page 5 Outlaw Audio Product Serial Number Write this number in the space provided on page 2 for future reference Speaker Outputs Use the OUTPUT binding posts to connect the amplifier to your speakers see page 5 Master Power Switch Turns the current to the amplifier on or off see page 8 AC Input Use the included power cord to connect your amplifier to an AC power source see page 8 Connecting Your Amplifier When making connections between any source components and the ampli fier or when making connections to any speaker be certain that both the input devices and the amplifier are turned off To assure that there will be no unwanted signal transients that can damage equipment or speakers it is always best to unplug all equipment before making any connections Modern electronic products often have a standby mode that may be activated even though the product may appear to be turned off Audio Signal Connections Connections with RCA type plugs When making connections with the RCA type plugs on interconnect cables make certain to gently but firmly insert them into the jacks marked unbal anced input on the back of the Model 7700 7500 Place input toggle in the Unbalanced position before attempting to operate Loose connections can cause intermittent sound and may damage your speakers The barrel assembly of some high quality RCA plugs may be very tight
16. nce consult the identification plate on your speaker terminals or the speaker s manual to verify polarity If you do not know the polarity of your speaker consult the speaker s manufacturer for further information Model 7700 7500 Multi Channel Power Amplifier 5 Owner s Manual Model 7700 Rear Panel Connections Model 7700 Rear Panel Connections ar 7 1 Channel Preamp Processor or Receiver aer gt connection Do not use both ero _ 12V Trigger Cali pr OIG a I G T l Lo C l Irro i pp O i ilo lA ili ili H EH HT HT HI HT HI IH ili L i L 4 HE Way l Remember to led maintain the di proper polarity when connecting speakers to your amplifier 6 Outlaw Audio Owner s Manual Model 7500 Rear Panel Connections Model 7500 Rear Panel Connections I NI Remember to maintain the proper polarity when connecting the Model 2200 to your speaker Nar 1 Channel Preamp Processor or Receiver For each channel use either a balanced or unbalanced connection Do not use both Unbalanced 12V Trigger Outputs 1 oi l pil it ill ill ill ill ill ill ill ill Il O Ie a i i I gt Il I L lar OUTPUTS Model 7700 7500 Multi Channel Power Amplifier 7 Owne
17. nnections have been made you are ready for listening First turn on the source components and processor in your system It is always a good idea to turn on your amplifier LAST This avoids the possibility of any turn on pops or transients from other equipment being amplified and sent to your speakers where they may cause damage Always start with a low volume level on your controller or preamp to avoid damage to your speakers Manual On Simply press the front panel Power Standby button until the light is illuminated There will be a short pause from the time the power is turned on until power is applied to the speakers This is intentional and protects your speakers from damage while the amplifier stabilizes You may also hear a relay click during start up This is also normal To turn the unit off press the Power Standby button again The indicator light will go out Automatic On Make certain that the connection to the processor or other controlling device is correct as shown on pages 6 7 Whenever the controlling device is turned on the amplifier will automatically turn on after a short pause This pause is inten tional and it protects your speakers from damage while the amplifier stabilizes You may also hear a relay click as during start up This is also normal To turn off your amplifier simply turn off the unit that feeds the amplifier it s audio signals The amplifier will automatically go into a stand by mode in a few moment
18. of similar gauge As with all electrical devices do not run power cords under rugs or carpets or place heavy objects on them Damaged power cords should be replaced immediately with cords meeting factory specifications Wiring Cables that are run inside of walls should have the appropriate markings to indicate complaince with and listing by the UL CSA or other standards required by the UL CSA NEC or your local building Questions about cables inside of walls should be referred to a qualified customer installer or a licensed electrician or low voltage contractor Installation Location To assure proper operation and to avoid the potential for safety hazards place the unit on a firm and level surface capable of supporting 100 pounds or more When placing the amplifier on a shelf be certain that the shelf and any mounting hardware can support the weight of the amplifier and any additional items in the equipment rack or on the shelf When positioning the amplifier in its final location make certain that it has adequate ventilation on all sides as well as on the top and bottom In particular it is a good idea to provide at least two or three inches of room above the amplifier for air circulation DO NOT place CDs DVDs videotapes owner s manuals or other paper on top of or beneath the unit or in between multiple amplifiers in a stack This will block airflow causing heat build up degraded performance and may create a possi
19. onents one at atime and see if one or all of them is causing the problem The ultimate solu tion to this type of problem is to re wire your house with an isolated star type grounding configuration We recognize however that this may be impracti Set top Box Cable Feed cal and expensive In some cases the use of an approved AC Power Isolation Transformer of sufficient capacity may solve this problem Warning if you suspect that the grounding system in your home s electrical wiring is causing the hum problem it is important that you do not make any changes to the wiring yourself Only a licensed electrician should make any changes to household wiring and they must be made in full compliance with all local building safety and electrical codes Suggestion 4 Hum may also be caused by faulty earth grounds in your home s electrical system In the past cold water pipes were often used for the earth ground so it is important to make sure that your ground connection is still valid and has not become loose or corroded The cold water pipe method may no longer be valid in some locations due to requirements that the water meter be isolated from the water mains with a length of PVC pipe thus interrupting the ground circuit The safest and most reliable approach may be to provide your own ground This can be accomplished by having a licensed electrician drive at least five feet of copper jacketed steel grounding rod into the earth and using
20. other countries please call Outlaw Audio outlaw Outlaw Audio
21. r s Manual Amplifier Operation Power Control Connections Your Outlaw amplifier features a built in remote turn on system that will automatically switch the amplifier when another device in the system is switched on Remote Turn On Using Products Equipped With a 12 Volt Trigger Jack Press the front panel power switch on the amplifier so that it is in the ON posi tion Then using an accessory cable with a 3 5mm mono mini plug on each end connect the trigger output jack on the rear of the source device to the trigger input jack on the back panel of the amplifier When these connections are made the amplifier will automatically turn on whenever the triggering device is turned on Remote Turn on Using External AC to DC Power Converter If your processor or receiver does not have a dedicated trigger jack it is still possible to activate the unit for automatic turn on when a Switched Outlet is available on the rear of the source device To control the amplifier in this fashion you will need a small AC to DC power converter capable of delivering a6 to 12 volt DC signal The DC voltage should terminate in a standard 35mm type mini plug This type of converter may be obtained as a Power Adapter from many electronics retailers When installing press the Main Power Switch on the front panel of the amplifier in so that itis in the ON position Plug the AC adapter into a switched outlet that will be activated when you wish to have the amplifier t
22. rned off No power light LED Turn on Master Power Switch Amplifier will not turn on Remote trigger cable not properly connected Verify connection of trigger cable at both ends Amplifier turns on but no audio from one or more channels Input plugs not connected to proper jack or are loose Check input connections Confirm that the Unbalanced Balanced switch is in the correct position No audio from one or more channels Speakers not connected properly heck speaker connections at amp and speaker a Audio levels differ mproper settings or output levels from the processor or controller heck the settings on your preamp processor or controller A Audio plays then cuts off gt mplifier shorted heck speaker connections for short circuit at amp and speaker A Troubleshooting Your Outlaw Multi Channel Amplifier is designed for trouble free operation If you follow the instructions in this manual you should enjoy many years of high quality listening enjoyment However as with any sophisticated electronic device there may be occasional problems upon initial installation or during the life of the unit The items on this list are a brief guide to the minor prob lems that you may be able to correct yourself If these solutions do not rectify a problem or if the problem persists contact us for assistance Protection Circuitry Your Outlaw Audio Amplifier uses advanced protection circuitry
23. rooves on each side of the speaker cable When mak ing connections to the amp and speakers adhere to a consistent pattern of using one side of the wire to the red terminals and the other side to the black terminals When using cable with markings on one side only traditional convention is to consider the marked side of the wire as the red or positive connection and the non marked side as the black or negative connection Next loosen the knobs of the amplifier s speaker output terminals far enough so that the pass through hole is revealed Note that one conductor of the speaker cable should have no markings and the other should have a red line brand name markings a colored thread or some other positive indication Follow the proper connection instructions for your system with regard to which terminals are used Once the connections are made twist the cap back so that the con nection is secured but do not over tighten or use tools as this may break the delicate wire strands and decrease system performance If you are using spade lugs connect them to the speaker wire using the man ufacturer s instructions then loosen the caps on the speaker terminals Place lugs between the plastic cap and the back of the terminal Be sure to observe proper polarity using the appropriate speaker hook up icons for your system s configuration Using your fingers tighten to obtain a positive contact When using banana plugs connections may b
24. s Output Settings All volume and level adjustments are made at your preamp controller or sur round processor To assure proper sound field imaging it is always a good idea to re set the output levels of the channels on your processor when using the amplifier for the first time The circuitry in your new amplifier may be different from your previous one and by checking the output levels you will make certain that the processor amplifier and speakers are properly matched Care and Maintenance Cleaning When the unit becomes dirty wipe it with a clean soft dry cloth If necessary first wipe the surface with a soft cloth slightly dampened with mild soapy water then with a fresh cloth dampened with clean water Wipe dry immediately with a dry cloth NEVER use benzene thinner alcohol or any other volatile cleaning agent Do not use abrasive cleaners as they may damage the finish of the metal parts Avoid spraying insecticide waxes polishing agents or any aerosol product near the unit When You Are Away If you will not be using your home theater system for an extended period of time it is always a good idea to turn the unit off using the Power Switch on the rear panel of the amplifier This will prevent the automatic turn on circuits from accidentally turning the system on during your absence Owner s Manual Troubleshooting Troubleshooting Guide Problem Amplifier will not turn on Solutions Master Power Switch tu
25. s Unpacking Rear Panel Connecting Your Amplifier Audio Signal Connections Speaker Connections Model 7700 Rear Panel Connections Model 7500 Rear Panel Connections Power Control Connections Power Connection Amplifier Operation Manual On Automatic On Output Settings Care and Maintenance Cleaning When You Are Away Troubleshooting Protection Circuitry Outlaw Service Information A Few Words About Hum and Noise 10 Potential Ground Loops in a Complex A V System 0 0 o Oo auwneoninnaeoennaonrtiavrwniurt wt ww np 11 Specifications 12 The Outlaw Audio 30 Day Satisfaction Guarantee 12 Outlaw Audio Limited Warranty The contents of this manual are Copyright 2006 by Outlaw Audio LLC and may not be duplicated or reproduced by any means whether physical electronic or otherwise without prior written consent from Outlaw Audio Outlaw Audio and the Outlaw Audio logo are registered trademarks of Outlaw Audio LLC Specifications are those in effect at the time of printing Outlaw Audio reserves the right to change specifications or designs at any time without notice or obligation to modify existing units Owner s Manual Model 7700 7500 Multi Channel Power Amplifier Model 7700 Model 7500 Multi Channel Power Amplifier Congratulations As the owner of an Outlaw Audio Multi Channel Power Ampli fier you are in possession of a unique product Designed and manufactured in the United States it has been carefully designed to deliver the bes
26. t possible sonic performance This manual covers both the Model 7700 Seven Channel and Model 7500 Five Channel Fully Balanced Power Amplifiers We welcome you as a member of our Outlaw band and hope that your new amplifier brings many years of enjoyable listening to your music or home theater system In order to receive the maximum enjoyment from your new amplifier please take a few minutes to read this manual This important information will help you make certain that the amplifier is properly configured for operation with the rest of the equipment in your system This brief investment of time will provide major dividends by making certain that your amplifier is properly installed and optimized for the specifics of your installation Ifyou have any questions about this product its installation or operation please contact us via e mail at customerservice outlawaudio com or via telephone at 866 OUTLAWS 688 5297 Features Your new Outlaw Audio Fully Balanced Differential Multi Channel Amplifier is a state of the art high performance audio component It is built utilizing totally complementary circuitry from input to output The high current power supply is driven by a custom designed dual torrodial transformers with multiple windings for each channel Each output module has 12 discrete output devices 30 000 uF total filter capacitance and employs an advanced Opto coupled protection circuit Heat management is provided not by noisy fans b
27. that does not require fuses In the event that the amplifier senses a shorted speaker wire DC voltage on an input connection or thermal overload creates a condition that could potentially cause damage to the unit or to your speakers it will automatically shut down If this should happen first check all speaker wire connections both at the speakers themselves and at the speaker terminals on the back of the Model 7500 to make certain that none of the stands from any channel touch another channel and that none of the strands from a positive terminal touch those from a negative terminal Even a few stray wire strands can cause the unit to go into the protection mode After checking all speaker connections turn the unit back on If it continues to turn off check your speakers to verify that they are operating properly If all other potential sources of trouble check out properly contact Outlaw Audio for further assistance and information Outlaw Service Information Neither the Model 7500 nor Model 7700 contains any user serviceable parts If you suspect a problem that may require service assistance contact us at cus tomerservice outlawaudio com or by phone at 866 OUTLAWA 688 5292 It is important that any repairs be carried out only by an authorized service agent This will assure proper service and preserve the protection of your Limited Warranty Keep your sales slip or receipt in a safe place with this manual so that it will be
28. tion or normal set up claims based on any misrepresentation by the seller or performance variations resulting from installation related circumstances such as signal quality AC power or incompatibilities with speakers and or other system components During the warranty period Outlaw Audio will at its option either repair the defect or replace the defective product or the defective parts or com ponents thereof at no charge to the owner for parts and labor covered by this warranty If necessary repairs are not covered by this warranty or if a unit is examined which is not in need of repair you will be charged for the repairs and or the examination If non warranted repairs are needed we will notify you of the estimated cost and ask for your authorization to perform said repairs You must pay shipping charges incurred in getting your Product to the factory We will pay the return shipping charges if the repairs are covered by the warranty Please save the original shipping cartons as the unit MUST be returned in the original carton and packing Replacement cartons are available at a modest charge n Outlaw Audio If your product needs service please call Outlaw Audio at 866 OUTLAWS 688 5297 or 866 OUTLAWA 688 5292 You will need to present the original bill of sale to establish the date of purchase In the event that the proof of purchase cannot be established with the original receipt the warranty period shall b
29. urn on This may be the switched outlet at the rear of an AC receiver or other audio equipment Connect the 3 5mm mini plug from the adapter to the trigger input jack on the back panel of the amplifier The amplifier will now turn on and off automatically based on the status of the controlling device Power Connection Once all audio and system connections have been made connect the supplied power cord to the amplifier first and then connect it to an AC power source Please make certain that the amplifier is turned off and that the device con nected to the remote trigger input is off when connecting the power cord and plugging it into an AC outlet CAUTION Do not plug the amplifier directly into the Switched Acces sory outlet of another device These outlets are intended for use with low current draw products having a low current draw such as tuners CD players or cassette decks These cannot handle the high current draw of a power amplifier Using these outlets for a power amplifier is a significant safety hazard NOTE t is not recommended that you connect other power amplifiers or products with a high current draw to the same AC power circuit as the amplifier unless they are used with the remote power turn on and sequencing system The simultaneous turn on of multiple amplifiers on the same circuit may cause circuit breakers to trip due to the high current draw KI Outlaw Audio Amplifier Operation After all co
30. ut by custom designed heatsinks for each channel The 7700 7500 differential design virtually eliminates cross talk through a technology known as common mode rejection Compared to single ended designs the 7700 7500 requires half the rail voltage for a given power allowing for increased transient performance In addition with a slew rate nearly double that of a comparable single ended amp the utmost control over transients is maintained ensuring distortion free performance The result an amplifier that remains unequivocally true to the source material Unpacking The carton and packing materials used in shipping your new amplifier were specially designed to cushion it from the shocks and vibration of shipping We strongly suggest that you save the carton and packing materials to use if you move or if the unit ever needs to be shipped back to us for any reason To minimize the size of the carton in storage you may wish to flatten it by carefully opening the top and bottom flaps and folding the carton flat Other cardboard inserts may be stored in the same manner Packing materials that cannot be collapsed should be saved along with the carton in a plastic bag Your new amplifier has been engineered using heavy duty materials for high reliability and weighs a considerable amount 80 pounds for Model 7500 93 pounds for Model 7700 This substantial weight requires that you pay special attention to unpacking and installation of the unit
Download Pdf Manuals
Related Search