Oricom SECURE 200 Baby Monitor User Manual
Contents
1. ETTIN 18 MM Set the first or next feed time 1 Press OK key Set Time is shown on the display 2 Press OK key then follow the procedures in the Set the time of Clock Setting to set the hour and minute Set the interval for following feeds 1 Press OK key and use A V keys to select Set Interval 2 Press OK key follow the procedures in the set the time of Clock Setting to set the hour and minute Set Alarm on or off 1 Press OK key and use A W keys to select Alarm 2 Press OK key On or Off is shown on the display press OK key to set the Alarm on or off Set Alarm Volume 1 Press OK key and use A W keys to select Alarm 2 Press OK key and use A V keys to select Volume 3 Press OK key and use A V keys to select the alarm volume there 5 volume levels 4 Press OK key to confirm and Saved is shown on the display Language Setting The displayed information can be set in different languages 1 Press key and use A V keys to scroll to Language The display is shown below 3n BEN L I L Lanausae 2 Press OK key and use A V keys to select desired language 3 Press OK key and Saved is shown on the display TROUBLESHOOTING 19 The red power lights do not turn on when you plug 1 Check if the units are properly connected to the power supply in the power 2 Check if the power is turned2. is shown on the display press OK key to select 12 hours or 24 hours clock format Time displayed in the 12 hour clock format will include a small a to denote AM and a small p for PM Feed Time Setting If your baby is in a routine of regular feeding intervals you may wish to set your Baby Monitor to alert you when your MEN za 17 baby s feeds are due You have the choice to either set an alert just for your baby s next feed time or for your baby s next feed time plus subsequent feeds based on the interval time between them Firstly you will need to ensure that you have set the date and time on your Parent Unit s inbuilt clock Once you have done this you can either 1 Set the Time of day or night 24hr clock at which your baby s next feed is due eg 10 30 and then if you wish 2 Set the Interval between your baby s following feed start times eg every 3hrs 30mins be sure to include the time it takes to feed your baby 3 Finally you will need to switch the Feed Alarm on Now when your baby s next feed is due your Parent Unit will start beeping and the Display will show Feed Alarm Pressing any button on the Parent Unit will silence the alert and you can feed your baby If you have set the interval the alert will sound again when the next feed is due Press key on the parent unit and use A V keys to select Feed Time the display is shown below my T AER L LR L Feed Time
3. keys to select Select New 2 Press OK key and use A V keys to select lullaby and Play All There are 5 lullabies 3 Press OK key and Saved is shown on the display Sensitivity Setting You can adjust the sensitivity on the Parent Unit to monitor the sound from the Baby Unit For example if your baby is a particularly quiet sleeper you can increase the sensitivity levels so that you are sure to hear if your baby is disturbed or becomes uncomfortable 1 Press key on the parent unit and use A V keys to select Sensitivity The display is shown below n x LLL Sensitivity 2 Press OK key and then use A V keys to select the sensitivity level There are 5 levels 3 Press OK key to confirm and Saved is shown on the display Sound Alert Setting You can set the sound alert of the parent unit on or off and also the volume of the sound alert Press key on the parent unit and use A keys to select Sound Alert The display is shown below WM e LLL Sound Alert MEN ETTIN 15 Set On or Off 1 Press OK key On or Off is shown on the display press OK key to select Sound Alert on or off and Saved will be displayed on the parent unit Adjust Volume 2 In the Sound Alert setting menu use A V keys to select Volume and press OK key 3 Use A V keys to select the volume level There are 5 volume levels 4 Press
4. location Never use a frayed or compromised cord Never use or place your Parent or Baby units in or near moisture or water e g near bath or pool Immersing in water can cause electric shock and even death Power requirements In Australia this product requires an electrical supply of 220 240 volts single phase alternating current Use only the mains power adaptors supplied with this equipment Incorrect adaptor polarity or voltage can seriously damage the unit and or cause physical harm and even death The adaptors may become warm during use please take care when handling AC Adaptor Baby unit Input 100 240V c 50 60Hz Output 6Vp 500mA AC Adaptor Parent unit Input 100 240V c 50 60Hz Output 7V5c 420mA If you plan to use your Baby monitor whilst travelling overseas make sure that the voltage shown on the mains power adaptor is the same as the local mains power before connecting to the power supply Do not use any voltage converter with the monitor Do not dispose of the battery in a fire as they can explode Do not open unscrew or tamper with any part of this product Should your product go faulty contact Oricom Support 1300 889 785 or 02 4574 8888 Released electrolyte from the battery is corrosive and can cause damage to the eyes or skin It can be toxic and fatal if swallowed When your Baby Monitor is not in use it is recom mended that you disconnect it from the mains supply and remove the ba
5. your Baby s room and scroll through the menu during setting 15 Power On Off Key Press to turn the parent unit ON Press and hold to turn OFF 16 Menu key OK key Press to adjust the features of your Baby Monitor Press key to enter the menu options use A V keys to scroll through the menu choices and OK key to select Press key to exit 17 Link Light Green light ON indicates Linked to Baby Unit Flashing light indicates Link is lost 18 Display Indicates the current settings of your Baby Monitor including Battery level Date and Time Temperature Lullaby on off Lullaby melody 19 Noise level indicators 20 Torch key Press and hold to emit a soft beam of light from the top of the Parent Unit 21 Talk key Press and hold to talk to your baby or partner in the baby s room via the Baby Unit Charger Pod 22 Charging Light When Parent unit is placed in the Charger Pod the red charger light comes ON to indicate the battery is charging Light will remain ON to ensure optimum charge is maintained Baby Unit 1 Battery level indicator 2 Numbers Characters indicator 3 Temperature indicator 4 Lullaby on off indicator Parent Unit N O Q o NN Sensitivity indicator Night light indicator Battery level indicator Numbers Characters indicator Temperature indicator Fee
6. OK key to confirm and Saved will be shown on the display Temperature Setting You can monitor the temperature in the baby s room on both the parent and baby unit You can select the baby room temperature alert range The lower limit can be set from 18 C to 25 C and the upper limit from 19 C to 26 C If selected an alert on the parent unit will sound and the display will flash if the room temperature falls outside the selected range Please note the baby monitor cannot manipulate the temperature in your baby s room it only provides a temperature reading ETTIN 16 Mz Press key on the parent unit and use A V keys to select Temperature The display is shown below Mi T ax LLL Temrarature Set desired baby room temperature range 1 Press OK key Set Range is shown on the display 2 Press OK key use A V keys to set the upper and lower temperature limits 3 Press OK key to confirm and Saved is shown on the display Set temperature alert You can turn on and off the temperature alert on the Parent Unit 1 Use A V keys to select Temp Alert and press OK key to set the temperature alert on or off Set temperature alert volume 2 Or use A V keys to select Volume There are 5 volume levels 3 Press OK key and use A YV keys to adjust volume level press OK key to confirm and Saved is shown on the display Set degree Centigrade or Fahrenhe
7. on If not Press to turn on the power 1 You may have moved out of range Move closer to the Baby Unit and wait 5 seconds for the Link to establish 2 You may need to re establish the Link between the two units Turn both units off by pressing and holding the 5 and then turn on again by pressing the n th Can t hear your baby on the Parent Unit but the Link light is still glowing steadily Check if the volume is turned up on the Parent Unit The battery icon on the Display is flashing on the Your re chargeable battery is running low Return the Parent Unit to the Charger Parent Unit Pod to recharge it 1 The battery in the parent unit is not fully charged Charge the parent unit for 14 hours before use 2 The power to the baby unit may be turned off or disconnected and or the Baby unit may be turned off Reconnect the AC power adaptor to the baby unit and or turn on the baby unit 3 You may have to re establish the link between the two units You will need to remove the battery from the parent unit and register the parent unit back to the baby unit by following the instructions below Two horizontal bars flash centre of the display on A Ensure battery is removed from the Parent unit and baby unit if fitted and the AC the parent unit and Not Linked is shown power plug is disconnected from the Baby unit Press and hold the 5 on the BABY unit then plug in the AC power plug after 2 seconds when the b
8. Cricom Baby Monitor Secure 200 77 ADVANCED Hz eID lb TECHNOLOGY 4 User Guide TABLE OE CONTENT WARNINGS AND SAFETY INFORMATION GETTING STARTED YOUR BABY MONITOR LCD DISPLAY OF BABY MONITOR BASIC OPERATION MENU SETTINGS TROUBLESHOOTING PRODUCT SPECIFICATIONS GUARANTEE 14 19 20 21 IMPORTANT Please read this user guide thoroughly before use Your ORICOM Baby Monitor is designed to be an aid and should not be used as a substitute for responsible and proper adult supervision of a child The Baby Monitor has been designed to provide some added reassurance in the form of sound transmission for those times when you are not in the same room as your baby provided you always stay within hearing range of the baby monitor during use Your Baby Monitor is not a medical device nor a device to prevent cases of Sudden Infant Death Syndrome SID S or cot death and you should not rely on it for your baby s wellbeing It is important that you regularly check on your baby personally Make sure the Baby unit Parent unit and mains adaptor cables are kept out of reach of your baby and other young children within the house at all times at least one metre away from the baby s cot Never place the baby unit inside your baby s cot bed or playpen Never cover the Parent or baby units with clothes towels or blankets or any other item Do not place the cord in a high wear and tear
9. Unit cannot be used without a battery pack even if it is placed in the charger pod Press and hold 5 key to turn on the baby unit The Baby Unit should be placed about 1 metre to 1 5 metres away from the baby s cot on a flat surface Never place the Baby Unit inside the cot bed or playpen Make sure the unit cords and mains adaptor are out of reach of the baby and other young children Never place either Unit on antique or polished surfaces as slippage or scuffing may For the Baby Unit occur The unit may cause harm if it falls onto baby 1 In event of a power failure your Baby Monitor can or other young children switch to battery power It is therefore recommended Note D that you insert non rechargeable batteries in the If you place the Parent and Baby units too close together Baby Unit you will hear a high pitched noise called feedback this is 2 Remove the battery cover on normal The units are designed to be located in separate the back of the Baby Unit by rooms pressing and sliding it down Insert 3 alkaline batteries of the type AA not provided as marked Do not Press Talk button when the Baby unit and Parent on the unit and close the cover unit are positioned in the same room Feedback will be again Do not use rechargeable generated if the talk button is pressed when the Baby unit batteries in the Baby Unit and Parent unit are within 3 metres of each other 3 Plug the power cord into the po
10. aby unit night lights flash release the d button B Press and hold the 5 on the PARENT unit then insert the battery after 2 seconds the parent unit will sound an alert and the level indication red LED s will flash then release the 5 button C After a few seconds the PARENT unit will give a confirmation tone and the units will be re linked and ready to use NOTE Steps A and B need to be performed within 50 secs A high pitched ear piercing noise will be heard i from the units feedback Check if the Parent and Baby Units are too close together Move them further apart The green Link light on the Parent Unit is flashing and cannot hear the sounds from your baby s room rene Scone Operating Frequency DECT 1 8 GHz Up to 300m under optimum conditions The range is Range reduced in buildings up to 50m as a result of walls doors etc Input 100 240 Vac 50 60Hz Power supply Baby Unit Output 6 Voc 500 mA Non rechargeable batteries baby unit Type AAA 1 5 V Alkaline not included in the package contents Transmitting power Average 10 mW Maximum 250 mW Input 100 240 V c 50 60Hz Power supply Parent Unit Output 7 Voc 420 mA Re ch ble batt k P t Unit idees U Type 2 4V 750mAh Ni MH included in the package contents Operating time with charged battery Approx up to 10 hours Warranty Information Australia Oricom makes no other warranties or conditions express or implied includ
11. ailure by you to adhere to the warnings and follow the instructions set out in this user guide for the proper installation and use of the product 2 negligence on your part or misuse by you of the product 3 an uncontrollable external cause which results in the product not functioning including but not limited to power failure lightning or over voltage and 4 modification to the product or services carried out on the production by anyone other than Oricom or Oricom s authorised service provider Oricom will not be liable for any damages caused by the product or the failure of the product to perform including any lost profits or savings or special incidental or consequential damages Oricom is not liable for any claim made by a third party or made by you on behalf of a third party This limitation of liability applies whether damages are sought or a claim made under this Warranty or as a tort claim including negligence and strict product liability a contract claim or any other claim However this limitation of liability will not apply to claims for personal injury Nothing in this Warranty excludes restricts or modifies any condition warranty right or remedy which pursuant to the Competition and Consumer Act 2010 applies to this Warranty and which may not be so excluded restricted or modified For warranties that cannot be excluded restricted or modified Oricom limits the remedies available to those specified in the relevant legislat
12. baby unit and the parent unit close to each other as feedback may be generated Adjusting Volume You can adjust the volume at which you hear your baby There are 5 volume levels on both units and an Off setting on the parent unit On the parent unit Press A to increase the volume and V to decrease the volume On the baby unit Press A to increase the volume and V to decrease the volume When adjusting the volume the volume level will be displayed on the both units LCD display Baby alert You can set your Parent Unit to give an extra warning beep when the noise levels in your baby s room is high and the red lights on the sound sensor are lit This is particularly useful if the volume of your Parent Unit is turned down and you are just using the sensor lights to monitor the noise levels in your baby s room Follow the Sound Alert setting on the menu setting section to set the Sound Alert on or off and adjust the alert volume Paging If the Parent Unit is misplaced you can use button on the Baby Unit to locate the Parent Unit e Press and hold for 2 seconds on the Baby Unit The Parent Unit will automatically reset to mid volume and the paging alert will sound To stop the Page alert press any button on the Parent Unit or press again on the Baby Unit Note If no button is pressed the paging tone will stop after 2 minutes If the Parent Unit volume i
13. d time Alarm indicator Lullaby on off indicator Once you have set up your Baby Monitor you will be able to hear the sounds in your baby s room through the Parent Unit And also see the green and red sensor lights around the top of the Parent Unit rise and fall with the sound levels Note gt If the connection between the Parent and Baby Units is broken at any time the green Link light on the Parent Unit will flash slowly the parent unit will beep to alter you that the link has been lost and the green and red sensor lights will cease to react to any sounds Move closer to the baby unit or follow the directions in Troubleshooting chapter to re establish the link Power On Off Once connected to the power supply Press 5 on each Unit to turn on the power To switch off press and hold the 5 Monitoring Position the baby unit accordingly It should be placed 1 metre to 1 5 metres away from the baby s cot on a flat surface Take the parent unit to monitor Audio picked up by the baby unit microphone is depicted on the 8 lights on the parent unit 5 green BASI QPERATION M 9 and 3 red The more audio is picked up the more lights will be lit When no audio is picked up all 8 lights will be off e f the volume of the Parent Unit is turned off an alert will sound when the audio reaches the second red led Note Do not position the
14. emainder of the Warranty Period of the Oricom branded product in which they are installed whichever is longer During the Warranty Period Oricom will where possible repair and if not replace the faulty product or part thereof All component parts removed under this Warranty become the property of Oricom In the unlikely event that your Oricom product has a re curring failure Oricom may subject to the Competition and Consumer Act 2010 at its discretion elect to provide you with a replacement product of its choosing that is at least equivalent to your product in performance Oricom does not warrant that the operation of the product will be uninterrupted or error free ARANTEE 21 Oricom is not responsible for damage that occurs as a result of your failure to follow the instructions that came with the product These terms and conditions together with any specific terms and conditions contained in the user guide to the product purchased constitute the complete and exclusive agreement between you and Oricom regarding the product No change to the conditions of this Warranty is valid unless it is made in writing and signed by an authorised representative of Oricom Oricom will not be in breach of a warranty expressly set out in this User Guide or under the Competition and Consumer Act 2010 and excludes any liability for damages or any other remedy arising under any other legislation or the common law if the damage occurs as a result of 1 f
15. ery to full will be longer when the unit is charged and used at the same time The Parent Unit can t be operated on the charging cradle without a battery BASI OQPERATION M 13 Running the rechargeable battery right down at least once a week will help it last as long as possible The charge capacity of a rechargeable battery will reduce with time as they age so reducing the performance time of the parent unit Eventually they will need to be replaced 14 BATS CRS Sa Note All Menu settings operations are only available on the Parent unit During setting press key to exit Night light Setting You can turn on or off the night light on the baby unit via the parent unit 1 Press key on the parent unit and use A V keys to select Night Light The display is shown below Tn LLLI LL L Misht Liaht 2 Press OK key to select night light on or off and Saved is shown on the display Lullaby Setting You can play lullabies on the baby unit via the parent unit Press key on the parent unit and use A V keys to select Lullaby The display is shown below Start playing Press OK key Play is shown press OK key to play the lullaby and Saved is shown on the display To stop lullaby press OK again Stop is shown and Press OK to stop lullaby and Saved is shown on the display Selecting lullaby 1 Press OK key and use A V
16. ing as to acceptable quality and fitness for a particular purpose except as stated in this Warranty Any implied warranties that may be imposed by law are limited in duration to the Warranty Period Oricom warrants that the product is free from defects in materials or workmanship during the Warranty Period This Warranty does not extend to any product from which the serial number has been removed or was purchased outside of Australia This warranty in no way affects your statutory warranty rights under the Competition and Consumer Act 2010 or any other similar legislation The Warranty Period will be 3 years from the date of purchase of the product evidenced by your dated sales receipt You are required to provide proof of purchase as a condition of receiving warranty services You are entitled to a replacement product or repair of the product according to the terms and conditions of this document if your product is found to be faulty within the Warranty Period This Warranty extends to the original purchaser only and is not transferable Batteries or Battery Packs if supplied with this product are covered under this warranty for a period of 90 days Products distributed by Oricom are manufactured using new materials or new and used materials equivalent to new in performance and reliability Spare parts may be new or equivalent to new Spare parts are warranted to be free from defects in material or workmanship for thirty 30 days or for the r
17. ion Customer Support If you have any problems setting up or using this product you will find use full tips and information in the Troubleshooting section of this user guide as well as Frequently Asked Questions on our website www oricom com au If you have further questions about using the product after reviewing the resources above or would like to purchase replacement parts or accessories please call our Customer Support Team Our dedicated local support team are more likely to be able to help you than the retailer where you made your purchase Please retain your purchase receipt and attach to the back page of this user guide as you will need to produce this if warranty service is required Take a few moments to register your product online www oricom com au Australia Australia Oricom International Pty Ltd Email support oricom com au Locked Bag 658 Phone 1300 889 785 South Windsor NSW 2756 Monday to Friday 8am to 6pm AEST Web www oricom com au Fax 02 4574 8898 Qiicom New Zealand Email support oricom co nz Phone 0800 674 266 Monday to Friday 10am to 8pm Australian NST Web www oricom co nz
18. it You can choose whether to view the temperature of your baby s room in degrees Centigrade or degrees Fahrenheit Your monitor is pre set to Centigrade but if you wish to change it follow the steps below 1 In the Temperature setting menu use A V keys to select Degree F or Degree C 2 Press OK key to confirm and Saved will be shown on the display Clock Setting You can set the current day and time on the Display of the Parent Unit If you have unplugged your Baby Monitor from the power supply you will need to reset the Clock the next time you use it 1 Press key on the parent unit and use A W keys to select Clock the display is shown below Set the time 2 Press OK key and Set time is shown on the display Press OK key 3 Year is shown on the display Use A W keys to select the correct year Press OK key 4 Month is shown on the display Use A V keys to select the correct month Press OK key 5 Day is shown on the display Use A WV keys to select the correct day Press OK key 6 Hour is shown on the display Use A V keys to select the correct hour using the 24 hour clock Press OK key 7 Minute is shown on the display Use A V keys to select the correct minute Press OK key and Saved is shown on the display Set the hour format Use A F keys to select Hour Format press OK key 12Hrs or 24Hrs
19. laby Use A V keys to scroll to your choice of tune or to Play All Press OK key 4 Lullaby is shown on the display Press OK key to play the lullaby 5 To stop playing press OK key and Stop is shown on the display and then press OK key again Clock You can set the Display of the Parent Unit to show the current day and time It can be shown as either the 24 or 12 hour clock 24 hour clock is the default You will need to set the clock if you wish to use Feed Timer feature If you have unplugged your Baby Monitor from the power supply you will need to reset the Clock the next time you use it Follow the Clock Setting on Menu Settings to set the time OPERATION 1 1 BASI Temperature It is very important for your baby s health to ensure that they are kept at a safe temperature This includes the room temperature baby s temperature baby clothing and bedding contact your local health authority to ensure you are aware of the current recommendations and guidelines Your Baby Monitor can show the current room temperature on the Baby Unit and the Parent Unit and can even be set to alert you if the temperature falls outside of a defined range Follow the Temperature setting on the Menu Setting section to set the temperature range temperature alert and change from Centigrade to Fahrenheit Time for a Feed If your baby is in a routine of regular feeding intervals you may wish to set y
20. our Baby Monitor to alert you when your baby s feeds are due You have the choice to either set an alert just for your baby s next feed time or for your baby s next feed time plus subsequent feeds based on the interval time between them Follow the Feed Time Setting on the Menu Setting section to set the first or next feed time the interval for following feeds and to turn the feed alarm on or off Talk to your Baby You can speak to your baby from the Parent Unit perhaps to reassure them that you are on your way Press and hold gt key and speak into the front of the Parent Unit e Please note that you will not be able to hear your baby while you are speaking to them until you release p key again Customize your Baby Monitor to your Baby Some babies are louder than others You can customize the sound sensitivity of your Baby Monitor to suit your baby Set the sensitivity High for a quiet sleeper with a soft cry and set to Low sensitivity if they tend to make noise when sleeping or can make quite loud noises before they are truly crying Follow the Sensitivity Setting on Menu Settings to set the sensitivity Out of Range When the baby and parent units have no link with each other eg Out of range parent unit or Baby unit is not powered on the green Link light flashes The link break alert will be heard from the Parent Unit every 30 seconds and no link will be shown on both units LCD display When
21. s off the Parent Unit volume will reset to mid volume Night light The Baby Unit has a night light which emits a soft starry glow providing comfort and reassurance for your baby and allowing you to see them in a darkened room On the baby unit Press key on the top of the baby unit A soft light will turn on gently Press again and the light will fade away On the parent unit Press key and use A W keys to select Night Light then press OK key to turn on or off the night light Lullaby Your baby can be soothed to sleep by a gentle lullaby from the Baby Unit There are 5 tunes to choose from The lullaby feature can be turned on and off from both the Baby Unit and the Parent Unit and is indicated on both by a musical note icon The icon and the lullaby title show on both Displays when the lullaby is playing The lullabies will play for 15 minutes We recommend that you use the lullaby setting at the lowest volume setting which comforts your baby On the Baby Unit 1 Press 71 key The lullaby is shown on the display 2 Press s1 key to scroll to the different lullabies or to select Play all 3 Press m key again to start or stop the lullaby On the Parent Unit 1 Press key then use A keys to scroll to Lullaby Press OK key 2 Play is shown on the display Use A V keys to scroll to Select New Press OK key 3 The Display shows the current lul
22. the units are linked the green Link light will be steadily lit Torch The Parent Unit has a useful Torch feature Press and hold the button on the parent unit a soft beam of light is emitted from the top of the Parent Unit It is helpful when peeping into a darkened room to check on your baby Low Battery Baby Unit When the battery power is low the battery icon on the display will flash Parent Unit When the battery is low the battery icon on the display will flash And also the low battery alert tone will sound The unit still can be used for 30 minutes You should put the parent unit on the charger pod to recharge the battery Note Low battery alert can be suppressed by pressing any button Charging the Battery Depending on the usage the Parent Unit will work for up to 10 hours with a fully charged battery If a battery low alert tone is heard and the battery icon on the Parent Unit s display is flashing you should put the parent unit on the Charger Pod to recharge the battery You can still use your Parent Unit from the Charger Pod When charging the red power light on the charger will light steadily When you switch on your Parent Unit the battery icon on the display will indicate the current charge level of the battery Note The parent unit can be used on or off the charger pod When on the charger pod the battery will be recharged at the same time However the time it takes to charge the batt
23. ttery The Ni MH battery supplied with this product may be recycled once it is unable to recharge during normal operation Always observe your local Council State regulations regarding the disposal of your packaging materials exhausted batteries and old equipment Always recycle where possible Do not use your baby monitor in an explosive hazard area such as where there is gas leaking As there is a slight chance that the product could be damaged by an electrical storm it is recommended that users unplug from the mains supply during an electrical storm Cleaning and care The surface of the case can be cleaned with a dry soft lint free cloth Never use cleaning agents particularly aggressive solvents Apart from occasional cleaning of the case no other care is necessary Thank you for choosing this monitor from Oricom Your Secure 200 Baby Monitor offers the best Digital Technology INTERFERENCE Gz FREE FREQUENCY w DECT Digital Enhanced Cordless Telecommunications is the most widely used worldwide digital cordless technology offering amazingly clear sound long range and maximum voice security DECT operates on the 1 8Ghz frequency which eliminates potential interference from other common wireless devices such as cordless telephones wireless networks Wi Fi Bluetooth and cordless computer devices Pack Contents Depending on the model you have purchased this pack should contain the following items If an
24. wer input at the side of the Baby Unit and plug the adaptor plug into a mains power socket To prevent feedback do not take the Parent unit into the nursery baby s room Baby unit Sender j Temperature Sensor Picks up the temperature in your baby s room Battery Cover For non rechargeable batteries not supplied Night light key Press to turn On the night light Press again to turn Off the light Power On Off Key Press to turn ON the Baby unit Press and hold to turn OFF Page key Press and hold for 2 seconds to Page the Parent Unit with an audible alert Useful to call for assistance or to locate a missing Parent Unit Display Indicates the current settings of your Baby Monitor including Battery level Date and Time Temperature Lullaby on off Lullaby melody Play Stop key Lullabies Press to start or stop the lullaby music Music key Lullabies Press to select the lullaby melody 9 Microphone Picks up the sounds from your baby s room 10 Volume Up Down Keys Volume Reduces the lullaby volume Volume Increases the lullaby volume zz g MAC SESyANS AANO Left view of baby unit 11 DC 6V input Connecting to Power Adaptor 11 5 Parent unit Receiver 12 Battery Cover Rechargeable battery pack 13 Belt Clip 14 Volume Up Down Keys Adjust the volume at which you hear the sounds in
25. y of these items are missing please contact Oricom directly po SC2o0 SC2002 Parent unit receiver Baby unit sender Mains adaptor with charger pod NiMH rechargeable battery pack 1 2 2 4V 750mAh Mains adaptor with power cord ETIIN IEEE S Installation For the Parent Unit 1 Remove the Belt Clip by lifting the clip at the top and sliding it downwards 2 Then remove the battery cover on the back of the Parent Unit by pressing and sliding it downwards Note Observe the correct polarity and direction of the battery pack when inserting The black lip of the battery pack must be facing downwards as illustrated The unit will not operate if the battery pack is inserted incorrectly 3 Insert the rechargeable battery pack supplied as illustrated and close the battery cover again I 4 Place the Parent Unit into the Charger Pod 5 Plug the mains adaptor into a mains power socket The red charger light on the charger pod will illuminate indicating that the Parent Unit is charging the light will remain on to ensure optimum charge is maintained 4 ETTING STARTED 6 Press 5 to turn the Parent Unit on Before first use or if it has been out of use for a long time the Parent Unit will need to be charged for 16 hours before use After this time the Parent Unit will operate from the Charger pod when switched on Note that the Parent
Download Pdf Manuals
Related Search