Numark Industries TT1910 Turntable User Manual
Contents
1. Numark Professional Disc Jockey Products TT1910 Direct Drive Turntable OWNER S MANUAL NUMARK INDUSTRIES 11 Helmsman Road North Kingstown RI 02852 http www numark com TT1910 Safety Information and Product Registration CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN AX A CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE ANY COVER NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the user to the presence of un insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying this appliance CAUTION FOR USA amp CANADIAN MODELS ONLY TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE SAFETY INSTRUCTIONS 1 Read Instructions All the safety and operating instructions should be read before this product is connected and used 2 Retain Instructions The saf2. FREIGHT PREPAID with Return Authorization number to NUMARK INDUSTRIES 11 Helmsman Road Telephone 1 401 295 9000 North Kingstown RI 02852 U S A Fax 1 401 295 5200 Attention Service Department E mail numark numark com
3. counterweight until the tonearm is approximately balanced horizontally floats freely L 5 Refasten the tonearm with the arm clamp NS 6 Hold the counterweight stationary with one hand and rotate only 8 the stylus pressure ring to bring the number O of the ring into alignment with the center line on the tonearm rear shaft 7 Rotate the counterweight with scale ring clockwise to the ey correct stylus pressure following the manufacture s recommendation t 8 Set the anti skating control knob to the same value as the stylus pressure unless your manufacturer specifies otherwise 11 Install the dust cover to the main unit This lid is not designed for continual removal fe If you need to remove the lid press both release tabs at the same time CONNECTIONS 1 Connect the power cord to the power outlet 2 Connect the unit s output terminals from the rear of the unit to the PHONO jack of your DJ mixer or home amplifier receiver Output terminals Phono input of mixer L White gt L Channel eNotes Be sure to connect the ground terminal R Red gt R Channel firmly to the amplifier or receiver If this GND Spade gt GND connection is not made or is loose a power source HUM may result Numark The Proven Leader in DJ Technology 1997 Numark Industries 6 http www numark com JPERATING INSTRUCTIONS Push the power button to turn on the power the s
4. whichever is applicable limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of Communications WARNING To reduce the risk of fire or electric shock do not expose this appliance to rain or moisture Electrical equipment should NEVER be kept or stored in damp environments Please record the serial number of your unit as shown on the back of the chassis as well as the name of the l dealer from whom you purchased the unit Retain this information for your records Please return the warranty card enclosed to register your mixer with us MODEL TT1910 PURCHASED FROM l SERIAL NUMBER DATE OF PURCHASE Numark The Proven Leader in DJ Technology 1997 Numark Industries 2 http www numark com TT1910 CONGRATULATIONS You have just purchased the Numark TT1910 Professional Direct Drive Turntable This unit has been design to provide years of reliable operation in an easy to use design Thank you for purchasing a Numark Product and enjoy the TABLE OF CONTENTS Safety Information Page 2 Product Registration Introduction Page 3 Diagram and Parts Description Page 4 Assembly Page 4 Operating Instructions Page 7 Specifications Page 7 Warranty and Service Page 8 Contents of this package l 1 Main Unit 2 Turntable platter 3 Turntable mat 4 Dust cover 5 45 rpm adaptor 6 Counterweight S
5. S ee ee ee ee ee I 7 Headshell cartridge attached on cetain models 8 Operating instructions 1 9 Registration Card 1 Numark The Proven Leader in DJ Technology 1997 Numark Industries 3 http www numark com TT1910 TT1910 DIAGRAM PARTS DESCRIPTION 1 45 rpm Adaptor 2 Anti static slip mat 3 Center Spindle 4 Stroboscope 5 Start Stop Button 6 Speed Select Button 7 Strobe Dots 8 Target light 9 Power Button 0 10 Headshell Pitch Control Slider Tonearm Arm Rest Cueing Lever 1 1 1 1 Anti skating Knob Counterweight 12V BNC Light Connector 18 Hinge For Dust Cover 11 12 13 14 15 16 17 18 Numark The Proven Leader in DJ Technology 1997 Numark Industries 4 http www numark c TT1910 ASSEMBLY 1 Remove the main unit with the packing from the box and take off the packing material DO NOT DISCARD ANY PACKING MATERIAL The headshell counterweight and other parts are contained within the packing material 2 Set the 45 rpm adaptor on the main unit 3 Set the voltage selector switch to the 110 127 or 220 240V position according to the voltage of power supply This unit has been preset for 110 127V AC 4 Insert the turntable platter onto the center spindle 6 Set the turntable mat on the platter 7 Installing the cartridge When installing a cartridge re
6. en subjected to misuse neglect accident incorrect wiring not our own improper installation or use in violation of instructions furnished by us nor extended to units which have been repaired or altered outside of our factory nor to cases where the serial number thereof has been removed defaced or changed nor to accessories used therewith not of our own manufacture Numark reserves the right to make changes or improvements in its products during subsequent production without incurring the obligation to install such changes or improvements on previously manufactured equipment To place this warranty into effect the enclosed WARRANTY REGISTRATION CARD must be returned to Numark Industries LLC within thirty 30 days after date of purchase This warranty gives you specific legal rights and you may also have other rights which vary from state to state bt of Mal l Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you EQUIPMENT TRANSPORT l A Return Authorization number should be obtained from Numark through the addresses or phone numbers below l _It is the customer s obligation when returning faulty cauipae to propery pack the Numark equipment in its original packaging Failure to do so may inadequately protect the equipment in transit and therefore orale the customer s warranty The defective Numark equipment should be sent
7. ety and operating instructions should be kept for future reference 3 Heed Warnings All warnings on this product and in these operating instructions should be followed 4 Follow Instructions All operating and other instructions should be followed 5 Water and Moisture This product should be kept away from direct contact with liquids 6 Heat Avoid placing this product too close to any high heat sources such as radiators 7 Power Sources This product should be connected to a power supply only of the type described in these operating instructions or as marked on the unit 8 Power Cord Protection Power supply cords should be routed so that they are not likely to be walked upon or pinched by items placed on or against them When removing the cord from a power outlet be sure to remove it by holding the plug attachment and not by pulling on the cord 9 Object and Liquid Entry Take care that objects do not fall into and that liquids are not spilled into the inside of the mixer 10 Damage Requiring Service This product should be serviced only by qualified personnel If you have any questions about service please contact Numark at the number s shown on the back cover of this manual 11 Grounding or Polarization Precautions should be taken so that the grounding or polarization means built into the mixer is not defeated NOTE This apparatus does not exceed the Class A Class B
8. fer to the operating instructions of that cartridge During installation attach the stylus protector to guard the stylus tip from damage If you have purchased a unit with the cartridge included then that cartridge is already installed on the headshell You may skip to line 8 1 Connect the lead wires to the cartridge terminals The terminals of most cartridges are color coded Connect each lead wire to the terminal of the same color White L Left channel Blue L Left channel Red R Right channel Green R Right channel 2 Install the cartridge to the headshell and tighten it with screws provided with the cartridge 8 Insert the headshell into the front end of the tonearm then turn the locking nut clockwise with the head shell firmly held horizontally Numark The Proven Leader in DJ Technology 1997 Numark Industries 5 http www numark com TT1910 9 Slide counterweight onto the rear of the tonearm _ Twist it lightly and it will screw onto the rear shaft of the tonearm ranean Counterweight 10 Adjustment of horizontal zero O balance with stylus pressure and anti skating 1 2 3 Remove the stylus protector do not touch the stylus tip during the adjustment Set the cueing lever to the lower position so it does not effect tone arm height Release the arm clamp and lift the tonearm from the arm rest so it moves freely lt x rer re wa 4 Rotate the
9. peed indicator and the strobe illuminator will light up Place a record on the turntable mat when playing a 45rpm record with alarge center hole place the 45 rpm adaptor on the center spindle Set the rotation speed 33 45 to match the record Remove the stylus protector release the arm clamp Set the cueing lever to the up position Press the Start Stop button the turntable platter will start to rotate Move the tonearm over the desired groove Set the cueing lever to the down position the tonearm will descend slowly onto the record and play begins To suspend play lift tone arm with cueing lever When play is finished raise the cueing lever move the tonearm to the arm rest secure the tonearm with the arm clamp 1 Press the Start Stop button to stop the platter rotating push the power button to turn off the power ARGET LIGHT iis unit is provided with a target light for illuminating the stylus tip during play Push the target light button the target light will be raised into position for illuminating the stylus tip When not in use keep the target light lowered through depression ITCH ADJUSTMENT 1e pitch control is variable in a range of 10 During play observe the strobe dots if the strobe dots appear to the right the pitch is slower than the rated speed if flow to the left the pitch is faster than the rated speed if the strobe dots appear stationary which means the platter is in normal
10. rpm more than 600g cm Electronic Brake Less than 0 20 55dB DIN B Universal s shaped tubular arm 220mm AC110 127V 220 240V 50 60Hz 20 Watts 450 x 350 x 148 mm 17 3 4 x 13 3 4 x 5 7 8 7 5Kgs 16lbs Specifications and design may be changed without notice for improvement Numark The Proven Leader in DJ Technology 1997 Numark Industries 7 http www numark com Numark Professional Disc Jockey Products Warranty and Service Information Numark Industries LLC and Numark International Inc hereafter Numark warrants each new product manufactured and or supplied by it to be free from defects in material or workmanship under conditions of normal use and service for 360 days beginning on the date of pure tase from an authorized Numark Dealer but not to exceed 2 years from date of shipment by umark The Numark obligation under this warranty is limited to repairing or replacing at its option the product or part s therein which upon examination by Numark shall appear to be defective or not up to anor specifications providing the Numark product is returned transportation prepaid to umark Numark shall not be liable for any damages consequential or otherwise resulting from the use and operation of this product and makes no other warranty s either express or implied on this product including any warranty of merchantability This warranty does not extend to any of our products which have be
11. turntable speed Move the pitch control slider up or down to adjust the speed PLACEMENT TT1910 Do not place the unit in a location where it will be exposed to direct sun light or near a heating appliance Do not place the unit ina location where there is high humidity or a lot of dust Cartridge may pick up slight sound pressure or vibrations of the speakers coming along the floor or through the air resulting in howling Find a location which is very stable and free vibration The legs have functions for adjusting the height of the unit itself Adjust the legs to stabilize the main body horizontally MAINTENANCE Clean the stylus periodically with a soft brush to prevent the accumulation of dust eWhen the sound becomes distorted or noisy check the stylus If worn out replace it with a new one From time to time the dust cover and turntable cabinet should be wiped with a soft dry cloth Any volatile materials as alcohol thinner benzine etc may remove the paint or damage the luster should not be used SPECIFICATIONS Turntable section Type Driving method Motor Turntable platter Turntable speed Starting torque Braking System Wow and flutter S N ratio Tonearm section Type Effective length General Power supply Power consumption Dimension WxDxH Weight 2 speed full manual Direct drive 8pole 2phase brushless DC motor Aluminum diecast 330mm dia 33 I 3 and 45
Download Pdf Manuals
Related Search